Q1:which command to assign manualy IP to EX series using CLI
****X command set network IPV4 address:**** ****X configuration network address Ethernet0:**** ****X configuration network IPV4 address NIC0:**** ****X configuration network IPV4 address:**** this is my answer Q2:how to initiate a cisco Telepresence 1310-65 camera calibration ****Troubleshoot>Hardware setup>setup>show focus target**** this is my answer ****Troubleshoot>Hardware setup>camera>show camera target**** ****Harware setup>start>camera>setup>show focus target**** ****Troubleshoot>Hardware setup>camera>setup>calibrate**** Q3:which two standard supported for streaming live video on cisco telepresence content server (choose two) ****H265**** ****H263****this is my answer ****H270**** ****H261****this is my answer ****H262**** Q4:when an engineer try to pull log from an cisco EX90 codec for call setup issue using �log ctx sip packet debug 9� nothing happen, how to enable this debug ****collect log from webinterface**** ****enter log ctx sippacket debug all**** ****ssh into the codec to view the log**** ****enter the logoutput on command**** this is my answer Q5:how to enable existing remote jabber to register to cucm without VPN ****expressway with jabber guest**** ****vcs with jabber guest**** ****expressway with MRA**** this is my answer ****vcs with MRA**** Q6:end user is on a cisco telepresence session with remote participant and can control the camera at the remote endpoint. which feature is underlying ****FECC**** this is my answer ****DTMF**** ****FEC**** ****PIP**** Q7:which two actions take place for proper operation when using Advanced Networking on VCS (choose two) ****automatic routing must be enabled**** ****manual route must be added using x command routeadd**** ****network interface must reside in the same subnet**** ****NAT reflection must be enabled on the firewall**** this is my answer ****Network interface must reside in separate subnet**** this is my answer ------------------------- I have some remark: Q2:how to initiate a cisco Telepresence 1310-65 camera calibration ****Troubleshoot>Hardware setup>setup>show focus target**** this is my answer ****Troubleshoot>Hardware setup>camera>show camera target**** ****Harware setup>start>camera>setup>show focus target**** ****Troubleshoot>Hardware setup>camera>setup>calibrate**** I believe that correct answer is Troubleshoot>Hardware setup>camera>show camera target**** please check this link (Page 3-16): http://www.cisco.com/c/en/us/td/docs/telepresence/cts_1300/cts_1310/assembly/ guide/1310_assembly_guide.pdf For Q7 Q7:which two actions take place for proper operation when using Advanced Networking on VCS (choose two) ****automatic routing must be enabled**** ****manual route must be added using x command routeadd**** ****network interface must reside in the same subnet**** ****NAT reflection must be enabled on the firewall**** this is my answer ****Network interface must reside in separate subnet**** this is my answer I believe correct answers are: ****NAT reflection must be enabled on the firewall**** ****manual route must be added using x command routeadd**** Please check this link http://www.cisco.com/c/en/us/support/docs/unified-communications/expressway/118992- configure-nat-00.pdf Moh August 7th, 2016 --------------------------- Q1:which command to assign manualy IP to EX series using CLI Xcommand set network IPV4 address: configuration network address Ethernet0: Xconfiguration network IPV4 address NIC0: Xconfiguration network IPV4 address: � correct Q :how to initiate a cisco Telepresence 1310-65 camera calibration Troubleshoot>Hardware setup>setup>show focus target Troubleshoot>Hardware setup>camera>show camera target � correct Harware setup>start>camera>setup>show focus target Troubleshoot>Hardware setup>camera>setup>calibrate Q3:which two standard supported for streaming live video on cisco telepresence content server (choose two) H265 H263 � correct H270 H261 � correct H262 Q4:when an engineer try to pull log from an cisco EX90 codec for call setup issue using �log ctx sip packet debug 9� nothing happen, how to enable this debug collect log from webinterface enter log ctx sippacket debug all ssh into the codec to view the log enter the logoutput on command � correct Q5:how to enable existing remote jabber to register to cucm without VPN expressway with jabber guest vcs with jabber guest expressway with MRA � correct vcs with MRA Q6:end user is on a cisco telepresence session with remote participant and can control the camera at the remote endpoint. which feature is underlying FECC � correct DTMF FEC PIP Q7:which two actions take place for proper operation when using Advanced Networking on VCS (choose two) automatic routing must be enabled manual route must be added using x command routeadd � correct network interface must reside in the same subnet NAT reflection must be enabled on the firewall Network interface must reside in separate subnet � correct