Professional Documents
Culture Documents
Maytag
MDB8750AW
16022783
January 2004
Important Information
Important Notices for Servicers and Consumers
Maytag will not be responsible for personal injury or property damage from improper service procedures. Pride and
workmanship go into every product to provide our customers with quality products. It is possible, however, that
during its lifetime a product may require service. Products should be serviced only by a qualified service technician
who is familiar with the safety procedures required in the repair and who is equipped with the proper tools, parts,
testing instruments and the appropriate service information. IT IS THE TECHNICIANS RESPONSIBLITY TO
REVIEW ALL APPROPRIATE SERVICE INFORMATION BEFORE BEGINNING REPAIRS.
! WARNING
To avoid risk of severe personal injury or death, disconnect power before working/servicing on appliance to avoid
electrical shock.
To locate an authorized servicer, please consult your telephone book or the dealer from whom you purchased this
product. For further assistance, please contact:
CAIR Center
Web Site Telephone Number
WWW.AMANA.COM ............................................... 1-800-843-0304
WWW.JENNAIR.COM ............................................ 1-800-536-6247
WWW.MAYTAG.COM ............................................. 1-800-688-9900
! DANGER
DANGER—Immediate hazards which WILL result in severe personal injury or death.
! WARNING
WARNING—Hazards or unsafe practices which COULD result in severe personal injury or death.
! CAUTION
CAUTION—Hazards or unsafe practices which COULD result in minor personal injury, product or property
damage.
PRECAUCIÓN:
Desconecte la
energía eléctrica
antes de darie
servicio.
ATENCIÓN:
Solamente use
conductores de
cobre. Use cables de
suministro adecuados
para 75° (167°F).
! WARNING
To avoid risk of personal injury or death due to
electrical shock:
Generally, these checks will consist of taking readings 1. Motor Current - the reading can be taken at the
at the wall receptacle in order to determine the leads on the motor start relay or at the male connec-
availability of voltage to the product. Voltage checks on tor.
individual components of a product are not
recommended due to the possibility of electrical shock. 2. Heating Element Current - The reading can be
Component part testing is best accomplished through taken using either lead to the element.
continuity checks with an Appliance Test Meter.
NOTE: Use of the meter on voltage higher than the Motor Test Cord
indicated range may cause permanent damage to the
meter. To prevent damage, first select highest range and
then lower the range for readings which fall within the ! DANGER
lower scale. To avoid risk of personal injury or death due to
electrical shock:
Clamp-On Ammeter
can be used to detect shorts. • Disconnect electrical power to dishwasher before
Overloads on the circuit breaker servicing.
or fuse can be traced • Always plug test cord into a properly grounded
to either the appliance receptacle.
or circuit breaker by • Always make connection to components before
checking the current plugging test cord into receptacle.
draw.
A motor test cord may be used to electrically check
operation of the various electrical components without
removing them from the unit. Testing in this manner
merely determines whether or not the part will function
independently of other electrical components. In order to
make accurate tests, proper connection of the motor test
cord is important. With the aid of the drawings under
Each circuit in an appliance has a "Normal" current Drive Motor Test, installation of the motor test cord may
draw, which is an indication of the performance of that be done quickly and accurately.
circuit. Current draw levels of less than or more than
normal give clues to possible malfunctions. The clamp-
on ammeter measures these circuits without breaking
the circuit by measuring the strength of the magnetic
field developed around each conductor. Current is read
by separating the conductors and clamping the jaws of
the ammeter around each conductor on which current is
read. Low amperage readings indicate problems, such Grounding and Polarity
as damaged heating elements, etc. High amperage
readings indicate the unit being tested is operating under
an increased mechanical or electrical load.
! DANGER
To avoid risk of personal injury or death due to
NOTE: Overloads on a circuit breaker or fuse can be electrical shock:
traced to the product being tested or the circuit breaker
(or fuse) by checking the products current draw. If the • Do not cut or remove the grounding prong from any
amperage reading is less than the breaker reading, the plug.
breaker or fuse box is at fault.
The receptacle used for all Maytag products operating on
120 VAC must be properly grounded and polarized.
! WARNING
To avoid risk of personal injury or death due to
electrical shock:
Washing
Qui etSer i es 300
Cycles Drying Heating Delay Options
Clean Sanitized
Heavy Extra
Wash Normal Tough Rinse
Light Rinse Auto START/ DELAY Heated
Wash 3 Sanitize Scrub
Wash Only Clean Cancel 1-9 Dry
Cycles Options
Clean
Auto Heavy Normal Light Rinse Quick Heated Extra Tough 160°
Clean Wash Wash Wash Only Wash
3 Dry Sanitize Scrub Wash Sanitized
Rinse Plus
MDB9750 Only
Cycle Description
Auto Clean Designed to auto select the number of fills and length of wash time based on soil level
of the dish load. Water usage ranges from 3 to 8 gallons.
Heavy Wash Designed to provide a longer cycle for washing items with heavy
food soils. Water usage is 8 gallons.
Normal Wash Designed to wash loads containing dishes with normal amounts of food soils.
Water usage ranges from 3 to 6 gallons.
Light Wash Designed to wash loads containing dishes that are lightly soiled. Water usage is 5
gallons.
Quick Wash Designed for light food soils. The cycle ends with a rinse and does not include drying.
Water usage is 4 gallons.
Rinse Only Rinses dishes being held until the dishwasher is full, and another
cycle is selected. This cycle helps reduce the potential for development of odors.
Water usage is 2 gallons.
Washing
Qui etSer i es 300
Cycles Drying Heating Delay Options
Clean Sanitized
Heavy Extra
Wash Normal Tough Rinse
Light Rinse Auto START/ DELAY Heated
Wash 3 Sanitize Scrub
Wash Only Clean Cancel 1-9 Dry
Cycles Options
Clean
Auto Heavy Normal Light Rinse Quick Heated Extra Tough 160°
Clean Wash Wash Wash Only Wash
3 Dry Sanitize Scrub Wash Sanitized
Rinse Plus
MDB9750 Only
Option Description
Tough Scrub™ This option adds fills, heat and/or wash time to the
Tough Scrub Plus™ wash cycle.
Extra Rinse This option adds an extra rinse to the cycle which helps in hard water situations.
160° Wash This option raises temperature in the final rinse to 160° F.
Heated Dry This option improves drying results by turning the heating element on and off during
the dry portion of the cycle.
Control Lock Lock's the control touch pads from unwanted usage. This option does not lock the
door.
Heavy Extra
Wash Normal Tough Rinse
Light Rinse Auto START/ DELAY Heated
Wash 3 Sanitize Scrub
Wash Only Clean Cancel 1-9 Dry
Cycles Options
Clean
Auto Heavy Normal Light Rinse Quick Heated Extra Tough 160°
Clean Wash Wash Wash Only Wash
3 Dry Sanitize Scrub Wash Sanitized
Rinse Plus
START/ DELAY
Cancel 1-9
MDB9750 Only
Display Description
Clean The "Clean" light illuminates at the end of the cycle and remains on until the door has
been open continuously for 30 seconds.
Washing The "Wash" light illuminates through all the rinse and wash portions of the cycle.
Heating Delay The "Heating Delay" light illuminates when the cycle is being extended to heat the
water.
Clean/Sanitized These two lights illuminate from the end of cycle until the next cycle is selected,
or the door has been open continuously for 30 seconds.
Delay The "Delay" light will illuminate whenever a delay count down is in progress, or until
the "Delay" pad is pressed again.
JDB1060
Washing
Qui etSer i es 200
Cycles Drying Heating Delay Options
Clean Sanitized
Heavy Extra
Wash Normal Tough Rinse
Light Rinse Auto START/ DELAY Heated Scrub
Wash 3 Sanitize
Wash Only Clean Cancel 1-9 Dry Plus
MDB8750
Cycles Options
Clean
Auto Heavy Normal Light Rinse Quick Heated Extra Tough 160°
Clean Wash Wash Wash Only Wash
3 Dry Sanitize
Rinse
Scrub Wash Sanitized
Plus
START/ DELAY
Cancel 1-9
MDB9750
! WARNING
To avoid risk of electrical shock, personal injury, or death, disconnect electrical power source to unit and discharge
capacitor through a 10,000 ohm resistor before attempting to service, unless test procedures require power to be
connected. Ensure all ground wires are connected before certifying unit as repaired and/or operational.
! CAUTION
Units covered in this manual are polarized. Reversing polarity of a unit or any of its components will cause
damage. To avoid reversing polarity, any wires disconnected or removed during service must be reconnected to the
same location. To ensure wires are reconnected to the proper location, tag or otherwise mark the wires before
disconnecting or removing.
Will Not Fill NOTE: Low water pressure can result in failure of the
Water Valve to close properly.
Wiring/Electrical Connections
Check for loose or frayed wire terminal connections.
Check for broken wire within harness. Repair or replace
as necessary.
Overflows
Wiring/Electrical Connections
Poor Washability Check for loose or frayed wire terminal connections.
Check for broken wire within harness. Repair or replace
as necessary.
Spray Arms
Check all Spray Arms for blockage of water ports or
cracks. Check for proper rack loading to avoid interference Continues To Drain
with Spray Arms during wash action. Check for proper
sealing, fastening, and movement of Spray Arms. Repair
Control Board
as necessary.
Check Control Board for proper operation.
Filters
Check for blockage of Strainer, Primary Filter, and Filter Poor Drying
Support. Repair as necessary.
Thermostat
Check mating surface of the High Limit Thermostat face Noise
to surface of tub enclosure. Contact area must be flat.
Adjust the thermostat placement if necessary. See
Banging
Technical Sheet, located behind Toe Panel for thermostat
Check for loose Spray Arms. Check for dishes interfering
data. with Spray Arm rotation. See loading information in the
User's Guide at the end of this manual.
Water Leaks Hammering/Chattering
Check Water Valve for, noise, low voltage, or high valve
coil resistance. Replace Water Valve if needed. Also,
Installation
check incoming water supply line for proper size and
Check Dishwasher for proper leveling and squareness in
pressure. Make sure the supply line is secured.
cabinet.
Grinding
Door Alignment
Check for objects in Pump Assembly. If objects are
Check proper alignment of Door Liner to Door Gasket.
found, inspect Pump Assembly for damage. Repair as
needed.
Door Gasket
Check for torn or damaged Door Gasket. Repair or
Vibration
replace as necessary.
Check components for source of vibration. Adjust and/or
tighten as needed.
Hoses
Check for loose hose clamps or hoses that leak. Tighten Will Not Start Or Program
hose clamps or replace hoses as needed.
Wash Motor
Check Wash Motor circuit. See data listed on the
Technical Sheet, located behind toe panel.
Drain Motor
Check Drain Motor circuit. See data listed on the
Technical Sheet, located behind Toe Panel.
Vent Assembly
Check Vent Assembly for proper operation.
Heating Element
Check Heating Element circuit. See data listed on the
Technical Sheet, located behind Toe Panel.
Does the cycle start Starting Problem Fill Problem Drain Problem
Yes Yes Yes No No
when the start/ Does it drain
Does it fill properly? Are there any leaks? Is it noisy?
cancel key is properly?
pressed?
No No No Yes Yes
Go to
Go to Leak
Repair or Noise
Is the water turned No Turn water Are the drain line Issues flow
No reconfigure Issues flow
Are any of the Go to No on to the unit? on and air break chart
drain chart
indicator lights for Yes Fuction operating correctly?
cycle and options flow chart system
illuminat ed?
Yes Yes
Go to No
Verify wiring
Is the power turned is connected
on to the unit at the No correctly at
breaker panel or junction box
fuse box? and turn on
Appearance Problem
power Does it look correct Yes
Complete
in the installation?
Yes
No
16022783 Rev. 0
Is there 105VAC No Correct
Troubleshooting Flow Chart
(minimum) at home It is
junction box? wiring issue No extremely
Is the unit level left
important to
to right and front
to back? LEVEL the
unit
Yes
Yes
Go to No
Fuction Adjust to
flow chart No touch f loor
Do all 4 levelling
and
legs touch the floor?
recheck
levelness
Yes
Yes
18
Yes
Complete
19
Check
for leaks
after each
manual
operation
below
Yes
No
16022783 Rev. 0
Troubleshooting Flow Chart
No
Is the rectangular
foam seal correctly No Install new
installed between
foam seal
vent and control
panel?
Yes
Complete
16022783 Rev. 0
Complete
Troubleshooting Flow Chart
No
Yes
Remove
and
Is the air/water inlet
reinstall air/
leaking at the tub
water inlet
connection?
with new o-
ring
Yes
No No Yes Yes
Complete Remove
and Replace Replace
20
reinstall the heater unit
heater nuts
Troubleshooting Flow Chart
Cycle Selection
Problem
Replace
drain pump
Yes Yes Yes
Verify the door is on
both hinges, both
See Wash Will the door clo se door springs Are both sides Adjust to
Is there food soil at No No
Yes Performance and latch are attached adjusted to same same
front of tub or door Flow Chart correctly,
completely? height? height
bottom? and installation
is correct
Yes
Yes Yes
No
No No Yes
Yes
No Yes Yes
16022783 Rev. 0
Yes Is food trapped in Yes Remove
Troubleshooting Flow Chart
No Yes No
Yes Bend back
Is rack warped
If the unit won't if possible
causing it to bind
start after or replace
pressing the start/ Repair
No
Is the unit level? Level unit cancel key installation
multiple times problem
No
then replace
control
22
replace-
See "A" in flow chart rack
ment part
Wash
Performance
flow chart
23
Go to No
Yes Are there staining No Function
Is the wash Important 1st
issues with parts of flow chart
performance good?
the machine? Steps
Yes
No
Use a Technician
Are the items getting No Are there staining Yes Accessories
detergent
wet? issues with the tub or will discolor Only Task
with
door? over time
bleach
Yes No
Yes
16022783 Rev. 0
No
Troubleshooting Flow Chart
Sanitize Issues
Heavy
Sanitize
Incoming water temp
must be 120°F
or grater (at sink)
Tub or door
Soil left on bottom
Only
Tub/Door No Yes
load
Issues What items are not Are they spotting, Is it only tall glasses short
getting clean? filming, or etching? in the corners? items in
Normal operation the
try heavy cycle Glasses corners
Yes No Spotting, Filming,
16022783 Rev. 0
inspect filter mesh. Is
filter
Troubleshooting Flow Chart
it torn?
Yes No
No Yes Unclog
No Is the carry over Is the drain pump
No Is there something drain
blocking the volume correct? clogged?
pump
Yes
dispenser door?
Yes
Clear
Is the sample port
sample Remove
clogged? No
port Replace obstruction Yes No
Is the heater
heater or
working?
thermostat
No
No Level
Is the unit level?
unit
Yes
No Install
Is the filter flapper
filter No Yes
present? Are you using
flapper Refer to
automatic D/W
U&C
detergent? Yes
Is the drain outlet Replace
Yes check valve stuck valve
Yes open?
24
inserted into the drain flapper water R/A & Detergent
port opening? ears hardness? recommendations Complete
Yes
25
IMPORTANT
This flow
chart
assumes all
wire
connections
have been
checked
16022783 Rev. 0
Troubleshooting Flow Chart
Instruct to
Instruct to raise water
Is incoming water No
Is anything blocking move items temp for
Yes temp at least 120F?
the vent openings in away from Vent better
the control panel? vent performance
openings Water Temp
Yes
No
Instruct that
Is the consumer only
Instruct to these items
Is Rinse Aid being No having problems Yes
use Rinse will not get
used? with plastic or Teflon
Aid Rinse Aid dry in any
items?
machine
Yes No Op Normal
Yes
16022783 Rev. 0
operation R/A operation
Troubleshooting Flow Chart
Dispenser
Yes Vent Yes
Run Field
Repair or Has the operation of No Service test
Is the vent flapper No
replace as the Turidity Sensor and verify
operating correctly? been verified? correct
necessary
Turbidity operation
Yes Yes
Sensor
Complete
26
27
C From Page 2
16022783 Rev. 0
Thumping distribution system? from back
Troubleshooting Flow Chart
No operation
wall into
and
back of tub
Rearrange placement
Instruct customer No
Are items moving load and to use less Rinse
Install a Yes
around and hitting secure Aid. See U&C for
Complete water
each other? items in recommended Remove
hammer
racks detergent items and
suppressor Are there objects
to eliminate amounts based Yes instruct
between chopper
on water customer to
No Complete and chopper plate?
Instruct hardness scrape hard
customer to objects
rearrange
Is the upper spray Yes load to No
arm hitting the tub? block jets No
coming Disassemble,
from lower look for parts
Verify
wash arm Yes Is there an No Are seals or that have
Rinse Aid Yes
No excessive amount of mechanical parts rubbed
tank is not
foaming in unit? rubbing together? together and
leaking
realign or
Is the lower spray Adjust, replace
arm hitting the Yes realign, or
heater element or replace
filter cover? parts
No
Grinding/
No Buzzing Look for hard Remove items
Does it sound like Yes and instruct
Single Yes objects between customer
Is the lower spray Instruct an intense grinding
Thump chopper and too scrape
arm hitting customer or buzzing?
Yes chopper plate. hard bjects
something that has and
This is the fallen through the rearrange No No
detergent racks? item
Does it sound like a Yes cup lid Ringing
single thump during hitting the This is
No Disassemble,
final rinse? door and is Does it sound like a caused by
No Are pump rotating Yes look for parts
normal ringing noise in Yes water
No Vibrating Popping
Are the wash arms Yes Is wash arm This is
Reroute stopped or rotating blocked or Readjust detergent
Is the drain hose drain hose slow, blocked, or Does it occur one
hitting rack? Yes insulation Does it sound like a YesYes cup lid
Yes Does it sound like a time only after a
16022783 Rev. 0
Is the door or other wash arm interfere with the Yes
replace as
Troubleshooting Flow Chart
part of the machine Yes Repair seam? Grinding hinge in the lower
neccessary
forced against installation corners?
cabinet? No
Remove
Does it sound like a Yes hard object No
grindingnoise? from drain
No pump
Tighten or
Is there a large leak Yes
replace No
at a wash arm hub?
wash arm
Does it sound like a Yes Is the door installed No
Install door
on the hinges
Consistently Loud grindingnoise? on hinges
properly?
No Instruct
Is the overall
Yes
Loud Are all 3 trim strips, customer
2 parts of kick plate,
consistentsound Does thenoise get Yes this is
& 2 foam pieces No
too loud? Are there objects louderafter water is normal Yes
installed correctly? Remove
No stuck between Yes fully drained? operation
Complete stationary and objects Grinding
No rotating parts of the Are the springs or
Yes wash arm hub? cables rubbing Yes Adjust or
No
against the cabinet replace
or the machine?
Are there large gaps Instruct to
between the Yes change Is there a leak at the Yes
Complete wash arm weld Replace
No machine and the installation No
cabinet/wall? or add seam? wash arm Complete
fillers
Yes Place cable
No Are the cables off
Complete back on
the pulleys?
Squeaking pulley
Replace
Does it sound like a
seal or Yes Tighten or
sqeakingsound as Yes Is there a large leak No
instruct as replace
machine coasts to a at a wash arm hub?
normal wash arm
stop?
operation Complete
No
28
No
Service and Disassembly Procedures
! WARNING
To avoid risk of electrical shock, personal injury, or death, disconnect electrical power source to unit and discharge
capacitor through a 10,000 ohm resistor before attempting to service, unless test procedures require power to be
connected. Ensure all ground wires are connected before certifying unit as repaired and/or operational.
! WARNING
To avoid risk of personal injury or death due to
electrical shock, ground wires and wires colored like
ground wires are NOT to be used as current carrying
conductors. The standard accepted color coding for
ground wires is green or green with a yellow
stripe. Electrical components such as the water valve
and motor are grounded through an individual wire
attached to the electrical component. Ground wires
should not be removed from individual components
while servicing, unless the component is to be
removed and replaced. It is extremely important to
replace all removed ground wires before completing
service.
Removal
1. Disconnect power to the machine. 2. Remove the Inner Door Panel. (See paragraph Inner
Door Panel removal).
2. Open the Dishwasher door.
3. Snap the Detergent Door shut.
3. Remove the 11 Torx™ screws along the sides and
top of the Inner Door Panel. 4. Gently lift the lever of the dispenser mechanism until
a click is herd. The Detergent Door releases. Re-
4. Separate the Inner Door Panel from the Outer Door. lease the lever.
5. Disconnect wires from the Dispenser Wax Motors 5. Lift the lever again. Now the actuator will lift the Rinse
before pulling the Inner Door Panel away from the Aid Plunger.
Dishwasher.
Removal
Removal
Switch Removal
2. Remove the Inner Door Panel. (See paragraph Inner Timing Sequence Chart
Door Panel removal).
Load Readings
3. To access PC Board, remove 1/4" screw on PC
Component Specifications
Board Housing Cover.
Manual Function Test
4. To remove PC Board, loosen (2) 1/4" screws
securing PC Board Base to Control Panel. Field Service Test
Electrical Schematic
5. Remove pin and ribbon connectors from PC Board.
Removal
Removal
DOOR GASKET
Removal
1. Open Door.
Replacement
Door Spring
NOTE: Always point spring hooks toward the Dishwasher. The purpose of the Over Pressure Filter is to filter
sediment missed by the lower filter rather than circulating
1. Disconnect power to the machine. it back through the wash.
4. Attach Cable to Cable Link. 2. Rotate filter down and remove from manifold.
7. Place large hook end of Spring into Spring Adjustment 1. Spread locking tabs and remove Wash Arm Retainer.
Bracket in proper location.
Water is supplied to the Top and Center Wash Arms The purpose of the Docking Station is to seal the water
through this tube via the Pump Assembly. The Manifold flow to the upper rack Wash Arm.
attaches to the Pump Assembly and runs vertically up the
rear and along the top of the Dishwasher Tub. The Removal
Manifold is attached to the Tub with a clip.
1. Slide Upper Rack forward to gain access to Docking
Removal Station.
1. Disconnect power to the machine. 2. Spread sides of Docking Station and remove from
Manifold.
2. Remove Racks, Stops, and Rack Assemblies.
Removal
Removal
Float
Heating Element
Wattage Checks
Removal
Two types of thermostats are used in the Dishwasher. A The valve is located behind the Support and Toe Panel,
Thermistor and a Limit Thermostat. mounted to the left side of the Tub Support. Inlet water
supply to the valve is directly below the valve.
The Thermistor is used to sense water temperature when
certain cycles or options are selected (Refer to Cycles & NOTE: Turn off water supply to the Dishwasher before
Options section). The Thermistor is part of the sensor servicing this component.
mounted in the Tub.
The valve is designed to operate at water pressures of 15 -
The other thermostat is a Limit Thermostat and is used as 120 psi.
a protective device to sense overheating of the Heating
Element. It is located behind the Front Support and Toe
NOTE: Low water pressure will affect the ability of the
Panel. The limit is mounted to the tub bottom. This
Water Valve to properly fill Tub in the required
thermostat has ¼" terminals and has a normally CLOSED
amount of time.
position.
NOTE: Refer to section labeled Technical Data for Incoming water temperature should be a minimum of 120
specifications on thermostat. degrees F. However, a higher water temperature will
enhance washing and drying results.
Removal
Removal
1. Disconnect power to the machine.
1. Disconnect power to the machine.
2. Remove Front Support and Toe Panel. (See paragraph
Front Support and Toe Panel removal). 2. Turn off water supply to the Dishwasher.
3. Press down on spring clip to release from Tub and 3. Remove Support and Toe Panels. (See paragraph
Front Support and Toe Panel removal).
rotate till clip unlocks.
4. Remove wires from Valve Solenoid.
4. Remove wires from thermostat.
5. Remove 2 1/4" screws securing Water Valve to Water
NOTE: When reinstalling, proper location and wiring of Valve Bracket.
thermostat(s) is critical.
6. Disconnect injector hose at valve outlet.
No Fill
Alternate Test: Use Motor Test Cord hooked directly to Air Water Inlet and Vent
the Valve Solenoid. Turn water supply on
and plug in test cord. If NO water is The Air Water Inlet is located on the left side of the Tub,
present, replace Water Valve. and mounted to the exterior of Tub. Removal of the Air
Water Inlet and Vent requires the removal of the
Dishwasher from under the counter. Vent only operates if
Overfill
cabinet becomes pressurized and will open flap on top of
Air Water inlet.
If Water Valve allows water to flow without power to Valve Removal
Solenoid, replace the Water Valve.
1. Disconnect power to the machine.
NOTE: The Water Valve is a non-repairable component.
The only servicing required is to clean the Inlet 2. Remove the Air Water Inlet Cover located on the left
Screen if needed. inside wall of Tub. Pull cover straight out to remove.
Inlet Screen 3. Carefully pull back insulation from the left side of the
Tub.
Sediment on the Inlet Screen can hinder water flow 4. Remove rubber hose from channel in Tub, or slip off of
through the Water Valve. fitting on inlet.
5. Grasp upper portion of the Air/Water Inlet. Pull and
Cleaning rotate the Air/Water Inlet clockwise to release it from
the Tub.
1. Disconnect power to the machine.
4. Clean screen.
1. Examine the Air Water Inlet Seal for damage. To remove, unlatch rear Rack Stop. Slide track out of
Dishwasher. Remove tub wheel shaft with Torx™ driver.
2. Align Air Water Inlet tabs with notches in Tub, and
rotate counterclockwise into position. NOTE: Tub wheel shaft contains a small steel washer.
Removal
The Drain Pump will drain water from the Dishwasher in 5. Remove Spray Arm.
various cycles. If a failure is suspected, the entire Pump
Assembly needs to be replaced. 6. Remove 3 Torx™ screws securing Filter Guard.
2. Remove Support and Toe Panel. (See paragraph Front 9. Disconnect wiring harness from Wash Motor
Support and Toe Panel removal). Assembly.
3. Disconnect lead wire from Pump Assembly. 10. Remove 6 Torx™ screws securing Discharge
Housing.
4. Disconnect drain hose from Pump Assembly.
11. Remove Torx™ screw securing Wash Impeller . See
5. Remove Torx™ screw through bushing in Pump bottom side of motor for access hole to lock motor
Mounting Plate. rotation while removing Torx™ screw. Insert screw
6. Rotate Pump Assembly to unlock from Tub. driver tip into access hole while removing screw.
E L E C T R I C A L R E Q U I R E M E N T S
This dishwasher is designed for operation WARNING
on an individual 120 VAC, 60 Hz grounded To prevent accidental contact with electrical connections,
electrical circuit. Use required fuse (15 amp) built-in dishwasher models must not be connected to a power
or comparable circuit breaker. Two wire source unless the dishwasher is completely enclosed, with
with ground service to the dishwasher is front panels in place. If the back or either side of the dish-
washer is exposed, a panel must be used to complete this
recommended for connection at the terminal
enclosure. Failure to follow this warning could result in death
box and for grounding. or serious injury.
G R O U N D I N G I N S T R U C T I O N S
This appliance must be connected to a WARNING
grounded metal, permanent wiring system;
To prevent the possibility of electrical shock, this dish-
or an equipment-grounding conductor must washer, as other electrical appliances, must be adequate-
be run with the circuit conductors and ly grounded. It is the responsibility of the installer at the
connected to the equipment-grounding point of installation, taking into consideration local condi-
terminal or lead on the appliance. tions and requirements. Failure to follow this warning
could result in death or serious injury
P L U M B I N G R E Q U I R E M E N T S
CHECK LOCAL PLUMBING CODES WARNING
FOR APPROVED PLUMBING
PROCEDURES AND ACCESSORIES. Disconnect electrical power to dish-
ALL PLUMBING SHOULD BE DONE washer before you start! Failure to
IN ACCORDANCE WITH NATIONAL
follow this warning could result in
death or serious injury.
AND LOCAL CODES.
Lavavajillas Empotrado
Instrucciones de Instalación
Deje las instrucciones de instalación y la guía del usuario con
el propietario.
R E Q U I S I T O S E L É C T R I C O S
Este lavavajillas ha sido diseñado para ADVERTENCIA
funcionar en un circuito eléctrico individual Para evitar un contacto accidental con las conexiones
aprobado de 120 VCA, 60 Hz debidamente eléctricas, los modelos de lavavajillas empotrados no deben
conectado a tierra. Use el fusible requerido ser conectados a una fuente de corriente eléctrica, a menos
que el lavavajillas esté totalmente encerrado, con los paneles
(15 amperios) o un disyuntor comparable. Se delanteros colocados en su lugar. Si la parte posterior o
recomienda una conexión de dos alambres con lateral del lavavajillas queda expuesta, se deberá usar un
servicio a tierra al lavavajillas para conectarlo panel para completar el encerramiento. Si se hace caso
omiso de esta advertencia, existe el riesgo de muerte o
a la caja de conexiones y a tierra. lesiones graves.
I N S T R U C C I O N E S PA R A L A P U E S TA A T I E R R A
Este aparato se debe conectar a un sistema ADVERTENCIA
de cableado permanente, metálico y puesto a Para evitar la posibilidad de choque eléctrico, este
tierra, o se deberá colocar un conductor para lavavajillas, al igual que otros aparatos eléctricos, debe ser
conectar equipos a tierra con los conductores puesto a tierra en forma adecuada. El instalador tiene la
del circuito y deberá conectarse a la terminal responsabilidad al respecto en el sitio de instalación,
de puesta a tierra del equipo o al conductor debiendo tomar en cuenta las condiciones y los requisitos
principal en el aparato. locales. Si se hace caso omiso de esta advertencia, existe el
riesgo de muerte o lesiones graves.
R E Q U I S T O S D E P L O M E R Í A
VERIFIQUE LOS PROCEDIMIENTOS ADVERTENCIA
Y ACCESORIOS DE PLOMERÍA
¡Desconecte la corriente eléctrica al
APROBADOS EN LOS CÓDIGOS
lavavajillas antes de comenzar! Si se
LOCALES DE PLOMERÍA. TODA LA
hace caso omiso de esta advertencia,
PLOMERÍA SE DEBERÁ REALIZAR existe el riesgo de muerte o lesiones
CONFORME A LOS CÓDIGOS graves.
NACIONALES Y LOCALES.
Lave-vaisselle encastré
Instructions d’installation
Laisser les instructions d’installation et le mode d’emploi au
propriétaire
I N S T A L L A T I O N É L E C T R I Q U E
Ce lave-vaisselle est conçu pour fonctionner
sur un circuit électrique séparé de 120 volts en
AVERTISSEMENT
courant alternatif et de 60 Hz. Ce circuit doit Pour empêcher tout contact accidentel avec les connexions
électriques, un lave-vaisselle encastré ne doit pas être
être protégé par un fusible de 15 ampères ou branché sur le courant électrique tant qu’il n’est pas
un disjoncteur de même calibre. Pour brancher complètement encastré et tant que le panneau avant n’a pas
le lave-vaisselle sur la boîte de connexions et été remis en place. Si l’arrière ou un des côtés du lave-
sur la mise à la terre, il est recommandé vaisselle est exposé, un panneau devra être posé pour
d’utiliser une connexion bifilaire. fermer cette ouverture. Ne pas respecter cet avertissement
risque de causer la mort ou de graves blessures.
R A C C O R D E M E N T S U R L’ A L I M E N T A T I O N D ’ E A U
CONSULTER LES CODES DE LA PLOMBERIE AVERTISSEMENT
DE LA MUNICIPALITÉ POUR CONNAÎTRE LES
PROCÉDURES ET LES ACCESSOIRES Couper le courant électrique alimentant
APPROUVÉS EN VIGUEUR. TOUTE LA le lave-vaisselle avant de commencer. Ne
PLOMBERIE DOIT ÊTRE EXÉCUTÉE pas respecter cet avertissement risque
CONFORMÉMENT AU CODE CANADIEN DE de causer la mort ou de graves
LA PLOMBERIE ET AUX CODES DE LA blessures.
MUNICIPALITÉ EN VIGUEUR.
2 Mounting Strips
(installed on unit)
2 Cintas de Montaje
(instaladas en la unidad)
Sound Seals 2 bandes de fixation
(select models only) (installées sur l’appareil)
Selladores de ruido
(ciertos modelos solamente)
Joints antibruit
(modèles sélectionnés seulement) Toe Panel Seal
(select models only)
Sello del Rodapiés
(ciertos modelos solamente)
Joint du socle
(modèles sélectionnés seulement)
1 2
5 6
237⁄8"to 2 3
4 ⁄8"
X= Adjusted Foot Height / Altura Ajustada de la Pata / Réglage de la hauteur du pied with no top strip / sin tira de adorno superior /
Mesure sans la tringle de finissage
7 8
1"
2"
H : X H : X H : X H : X H : X
331/2" : 1/4" 337/8" : 5/8" 341/4" : 1" 345/8" :13/8" 35" : 13/4"
335/8" : 3/8" 34" : 3/4" 343/8" : 1/8" 343/4" :11/2" 343/4": 11/2"
333/4" : 1/2" 341/8" : 7/8" 341/2" :11/4" 347/8" :15/8" 347/8": 15/8"
H= Opening Height / H = Altura de apertura / H = Hauteur d’ouverture
9
11 12 Installation may vary / Su instalación puede ser diferente
/ Votre propre installation peut varier
Refer to local codes / Consulte los códigos locales / Reportez-vous aux codes locaux
13 13A
14
13A
IMPORTANT /
13B 14 IMPORTANTE
15 IMPORTANT/IMPORTANTE 16
Never route cord or hoses under motor / Nunca coloque el cordón eléctrico ni las mangueras
por debajo del motor / Ne jamais faire passer câbles ou tuyaux flexibles sous le moteur.
17 18
OFF / APAGADO /
ARRÊT
19 20
GROUND/ PUESTA A TIERRA/ MISE À LA TERRE
1 2
GROUND
21 PUESTA A TIERRA
MISE À LA TERRE
22
BLACK TO BLACK (L1)
NEGRO CON NEGRO (L1)
FIL NOIR À BORNE
WHITE TO WHITE
NOIRE (L1) (NEUTRAL)
BLANCO CON BLANCO
(NEUTRO)
FIL BLANC À BORNE BLANCHE
(NEUTRE)
23 24
25 IMPORTANT/IMPORTANTE 26 IMPORTANT/IMPORTANTE
3/16"
3/16"
27 28
29 30
1/8
31 IMPORTANT/IMPORTANTE 32 IMPORTANT/IMPORTANTE
1/8"
33 34
1
3
2
Turn on water, power and machine / Abra la llave de agua, conecte la corriente y encien-
da el aparato / Ouvrir le robinet d’eau, l’alimentation et mettre en marche
35 36
Check for leaks, turn off machine / Verifique si hay fugas, apague el aparato / Vérifier
l’absence de fuites, mettre à l’arrêt
37 38
38A
Select models only
Ciertos modelos solamente 39
Modèles sélectionnés seulement
z z
z z
39A
Select models only
Ciertos modelos solamente 40 IMPORTANT/IMPORTANTE
Modèles sélectionnés seulement
z z
z z