Professional Documents
Culture Documents
WD-ACQUIRE
Manual
(August 2017)
2
Js0114.01 WD-ACQUIRE Product Description
Product Description
Device Type: In terms of electric hazard protective ability, the product is an ordinary
stationary device of B type of Category I.
Working system : Intermittent load continuous operation with signal input and output
and without application.
Operating conditions:
Power Requirements:
Power supply voltage: single phase 220V ± 22V, 50Hz ± 1Hz, sine wave
Input power: 1.0KVA.
Manufacturer's responsibility
Note
Provided the following conditions, the manufacturer is liable for the equipment safety,
reliability and performance:
1. Only authorized personnel can handle the installation, operation, adjustments, and
repairs;
3. Facilities are strictly used in accordance with the requirements of the manual.
Foreword
Thank you for purchasing our medical products.
Be sure to read the following precautions for your proper use.
Safety Precautions:
○Please read carefully Safety Precautions prior to use.
○ be sure to follow the details documented in Safety Precautions.
○ Graphic marks
2
Js0114.01 WD-ACQUIRE Foreword
Note
For danger prevention and safety, great attention should be paid to the
following:
Note
4
Js0114.01 WD-ACQUIRE Table of Contents
Table of Contents
1. OVERVIEW..........................................................................................................................................8
1.2 System Hardware.........................................................................................................................8
1.3 Routine Preventive Maintenance.................................................................................................9
1.4 Cleaning......................................................................................................................................9
CHAPTER II PREPARATIONS..........................................................................................................10
1. START APPLICATION.........................................................................................................................11
2. APPLICATION OVERVIEW..................................................................................................................12
3. QUIT APPLICATION...........................................................................................................................12
4. SOLUTION TO NO RESPONSE............................................................................................................13
CHAPTER IV.........................................................................................................................................20
CHAPTER V..........................................................................................................................................27
1. DR IMAGE ACQUISITION..................................................................................................................28
1.1 APR Setting................................................................................................................................28
1.2 Generator Control.....................................................................................................................29
1.3 Ionization Room Control...........................................................................................................29
1.4 Simulation Graph Control.........................................................................................................29
1.5 Image Acceptance......................................................................................................................31
2. DR IMAGE PROCESSING...................................................................................................................31
2.1 Marking and Measuring............................................................................................................31
2.2 Image Processing.......................................................................................................................32
2.3 Print / Report Image..................................................................................................................34
2. FEATURES.........................................................................................................................................40
3. INSTRUCTIONS FOR USE...................................................................................................................40
3.1 Select Image to Report...............................................................................................................40
3.2 Diagnostic Report Interface......................................................................................................41
1. PREFERENCES INTERFACE................................................................................................................45
2. PREFERENCES FUNCTIONS................................................................................................................45
2.1 MWL\WPPS MWL \ WPPS........................................................................................................45
2.2 Save \ Confirm...........................................................................................................................48
2.4 Configuration of System Info Display.......................................................................................52
2.4.1 Font Setting......................................................................................................................................52
2.4.2 Configure Image Info.......................................................................................................................53
2.4.3 Information around image, measurement, special font settings..................................................54
2.4.4 Set up of label..................................................................................................................................55
2.5 Playback Setting........................................................................................................................56
2.6 User Management.....................................................................................................................56
2.6.1 User Group Management..................................................................................................................57
2.6.2 User Management.............................................................................................................................58
2.7 DR APR Configuration..............................................................................................................58
2.7.1 Exam Program..................................................................................................................................58
2.7.2 Exam Sub-program...........................................................................................................................61
2.8 IP CONFIGURATION........................................................................................................................63
APPENDIX A.........................................................................................................................................65
1. PRODUCT NAMEPLATE.....................................................................................................................66
2. EXPLANATION OF GRAPHICAL SYMBOLS.........................................................................................66
6
Js0114.01 WD-ACQUIRE System Introduction
1. Overview
The system, mated with high-voltage generator, multi-function filming device, and
other accessories, is for radiography and diagnosis for medical institutions. By use of
digital imaging and capturing devices, the system completes the acquisition of
continuous fluoroscopy, pulse fluoroscopy (optional), spot imaging, DR image, and
DSA image (optional).
The system incorporates image acquisition, display, processing, and storage and
network transmission as a whole. The application performs the patient image storage
and management, image data acquisition, display, processing and storage, and
generator parameter selection and related information display, as well as Dicom
Worklist, Dicom Export / Import, and Dicom Print functions. And it has the following
advantages:
The system can be connected, through network hub, to other devices on the network,
such as PACS service, laser camera, Worklist workstation, the network interface of
which must support IEEE802.3, IEEE802.3u, IEEE802.3x standards. The port uses
RJ45 connector and meets the DICOM3.0 protocol.
8
Js0114.01 WD-ACQUIRE System Introduction
1.4 Cleaning
There is no strict cleaning rule for digital imaging system. In case of original dusty components, it
is best to follow these steps:
Keep all system components from water and corrosive
Note cleaner.
Computer:
Wipe out the dust outside the computer case by a clean, soft cloth.
Image display:
Cleanse the monitor screen with normal glasses cloth. First make sure power-off,
spray the cleaner on a soft cloth in fear that the liquid leak to the display's internal
components. Vacuum the dust residing in the upper part of the display. Leave no
left scraps of paper behind; the blockage of vent may cause the monitor
overheating and spontaneous combustion. Wipe the monitor screen by anti-static
cloth regularly.
Keyboard:
Blow away the dust and scraps of paper gathered inside the keyboard. A vacuum
cleaner can be used, but ensure the keyboard is not loosen to avoid being sucked
into the vacuum cleaner.
Chapter II Preparations
10
Js0114.01 WD-ACQUIRE Preparations
1. Start Application
Follow these steps to start the application:
Enter the user name and password and click OK to the main interface.
Each user has his or her name and password to get access.
Note
2. Application Overview
Overview of the Application is shown as Figure 2.2. The interface is divided into four
areas:
The right corner is the Functional Switch Bar. You can go to Cases to be examed,
Historical images, gastrointestinal images, DR images, Diagnostic reports, System
configuration, or Exit;
In the Infobar at the top, you can enter patient name, patient ID, and other information
for query.
Infobar displays the version of the application, printer connection status, PACS server
connection status, generator connection status, machining center status, medicine ball
heat capacity, and total fluoroscopy time. Other important system info also appears in
the Infobar.
3. Quit Application
12
Js0114.01 WD-ACQUIRE Preparations
Click Exit on the right side of the interface, and then the prompt is given
in Figure 2.3.
4. Solution to No Response
The application rarely makes any response. Use the following method to
eliminate it if failure occurs.
Select the application from the running programs and click End Task.
14
Js0114.01 WD-ACQUIRE Cases to be
Examed
Query fields include: patient name, patient ID, medical record number, requesting
program ID, and pre-exam date. Users fill out one or more query fields to query.
When patient name and patient ID duplicates the information on the server, the two
pieces of information will be combined into one in the acquisition interface.
For the query of current cases to be examed, the entire data retrieval will be done
according to the information filled out.
Figure 3.3 Drop-down box of pre-exam date Figure 3.4 Specified date
After clicking the drop-down box of pre-exam date, the options are shown as Figure
3.3. Click specified date to pop up a new dialog box of Day settings in Figure 3.4.
3. Query
Click Query to list the matching records from worklist service and local database in
Cases to be examed. If worklist service is not configured, then only the query of local
database will be done.
4. Refresh
Worklist is refreshed in the background in a certain time interval to copy the matching
records to the local database. Specific interval and conditions can be set in mwl of the
configuration interface. Refer to System settings for details.
16
Js0114.01 WD-ACQUIRE Cases to be
Examed
Select Cases to be examined from the list, double-click or click to enter the
corresponding acquisition interface based on the device type of current patients.
In the event of emergency case, click the button to go directly to the default
acquisition interface.
6. Register
Click Register. The dialog box as shown in Figure 3.6 appears, of which the
information marked with * is required.
Fill out new patient's name, sex, age, and exam sub-class and other information in the
Infobar, and patient name and number are necessary.
The corresponding relations of exam sub-class and exam class can be set via the
configuration interface.
Add
After entering, click and the patient's basic info will be saved and added
to Cases to be examed.
Edit
The display of list is configurable. Click the right mouse button to pop up a dialog box
in Figure 3.7.
18
Js0114.01 WD-ACQUIRE DR Image Acquisition and Processing
Chapter IV
Management of Historical Cases
Query
Query a case examed. See details as Chapter III.
Edit
Click Edit to modify the existing case in the pop-up dialog box.
20
Js0114.01 WD-ACQUIRE DR Image Acquisition and Processing
Click Edit to modify the existing case in the pop-up dialog box. You can edit the
patient's name, medical record number, gender, age, date of birth, height, weight,
phone, patient number, exam class, attending physician, referring physician, and
applying department, and click Ok.
Delete
Click the left mouse button, select the Cases to delete, and click to delete
Cases and images (you can use Ctrl or Shift key for selection of multiple cases).
Lock
Click to lock and unlock Cases. The cases locked will be displayed as TRUE
in the Lock / Unlock column, and can’t be deleted and edited at that time, and only be
unlocked by the locker or staff with high-level permission. The cases unlocked will be
shown as FALSE in the Lock / Unlock column.
Thumbnail View
Click one case, and the thumbnails of all the current exam sequences in the thumbnail
list will be displayed. Move the mouse to the thumbnails and such information as
shooting time, Device type, Print, and Send will be shown as the figure:
Figure 4.3
Right-click the thumbnail to send, edit image name, or delete.
Send: Send current image by PACS to main server.
Edit image name: Add and edit the name of current image.
Delete: Delete current image.
3. Send
On the condition of connecting with the specified server, select the Cases, click
to send all data to the server. On the lower right of the interface a prompt pops
up, showing Sent successfully. If the connection to server is incorrect, a failure notice
appears.
DICOM Export
Write cases data in the DICOM-DIR format to VCD or DVD. Before that the system
sends the data to cache.
DICOM Import
Import cases data in the DICOM-DIR format from VCD or DVD.
DICOM Send
Send cases data to the DICOM file server.
22
Js0114.01 WD-ACQUIRE DR Image Acquisition and Processing
The left is cases tree graph, showing the current case history available on the
computer. It is categorized into Local (Today) and Local (All). Case history is saved
in the computer's hard disk, recorded in the current database and can be exported. The
case history can be read, play backed, and exported from the system.
The edit box on the up right is display area of case history. When a user selects an
item of the left tree graph, the relevant information will be displayed in the area of
case history.
The case history browse area is on the right. When a user selects an item of the left
tree graph, the sub-items of the current item will be displayed in the case history
browse area. One or more items can be selected once.
Click on the right side to search all case history on the current
computer and display on the left case history tree graph. Find the case history from
the tree graph and click it for DICOM send. All sub-items of the currently selected
item are displayed in the case history browse area, and relevant information, in the
case history information display area.
Select one or more items in the browse area, and server name in the function area, and
click . The specified case history will be sent to the specified computer.
In the process, the speed is shown on the progress bar on the right side of function
area. And sent successfully, failed to send, and total amount are also displayed below.
If the user switches to the image acquisition interface and press hand brake or foot
brake to start image acquisition, the case history sending will be suspended
automatically to ensure the quality and efficiency of image acquisition, and resumed
after the end of image acquisition.
Click to show the case history on the current computer on the left tree
graph (as described above).
Find the case history available to export from the tree graph and click it for DICOM
Write. All sub-items of the currently selected item are displayed in the case history
browse area, and relevant information, in the case history display area.
Select one or more items in the case history browse area, click to pop
up the dialog box asking Empty the cache. Select yes to empty and then the specified
case history is buffered in the cache. Select No to pop up another asking Add the
images on the cache, click Yes to add, and No to go to the interface as shown in
Figure 4.5.
In the process of image cache, the space used and space available of the current cache
will be present on the progress bar on the left side of function area.
24
Js0114.01 WD-ACQUIRE DR Image Acquisition and Processing
Select the writing equipment and speed in parameter setting and click Write to start.
Click Close the window after writing to exit.
Chapter V
DR Image Acquisition & Processing
26
Js0114.01 WD-ACQUIRE DR Image Acquisition and Processing
1. DR Image Acquisition
Fill in patient info in the interface Cases to be examed. Enter DR image interface after
confirming the exam device of DR, and click Acquire on the top right to go to the DR
image acquisition interface, as shown in Figure 5.1.
The top of the interface shows the info of the patient currently collected; APR setting
area is on the left, the simulation area of selected exam sub-class, at the bottom, the
shooting guide area, at the middle black zone, and generator control area and
ionization chamber control area, on the right from top to bottom.
, Is to set Kv, mA, ms, and mAs. When setting Kv value, press the left
mouse button to quickly add or subtract.
After AEC exposure, the display bar shows the actual exposure time. If an error
occurs in the generator, the error message and code are displayed in the display bar.
The generator can be reset (only for the error when it can be reset).
If any one of the three views of the ionization chamber is selected, then the generator
is in the way of AEC exposure. All or either two views can be selected, and once
selected, the corresponding exposure time of the views can not be manually adjusted.
There is no limit for other parameters.
Select the corresponding body of human body model according to the actual exam
sub-class and click right. A drop-down list of exam sub-class appears as shown in
Figure 5.2.
28
Js0114.01 WD-ACQUIRE DR Image Acquisition and Processing
Users can view the number of exam class in the list. Select the exam sub-class,
double-click the left mouse button. The mimic diagram appears in the bottom of the
interface, as shown in Figure 5.3.
Select the exam sub-class according to needs, and the corresponding mimic diagram is
displayed in the bottom. Click to delete the diagram. When the guide map
is taken, click to delete the original image, and then click to delete
the mimic diagram.
When the captured image is accepted, the system returns to the interface “DR image
acquisition” and the guide image becomes a thumbnail. Select the next guide image
and set the corresponding APR parameters; if the captured image is rejected, the
system also returns to the interface, but the current guide image remains unchanged
and users can start the new acquisition of current exam sub-class.
2. DR Image Processing
After DR image acquisition, or during browsing the historical images of DR device,
the interface DR image playback processing is accessible, as shown in Figure 5.4:
The current patient info is shown at the top, thumbnail, on the left, image display area,
in the middle, and tool area, on the right.
Calibrate : Select Calibrate, drag the mouse on the object in known length
to draw a line, choose calibration unit and length. In general, a straight line is
automatically calculated according to image, and can be adjusted as calibration line;
30
Js0114.01 WD-ACQUIRE DR Image Acquisition and Processing
Measure area and calculate histogram : Select Measure area, draw a box
on the image to measure area.
Measure angle : Select Measure angle. Draw the first line on the image, and
the second line starting from the end of the first line to measure angle;
Image mark : Select an image and click this button in the toolbar to display
all marks on the image.
Add Left and Right :Click the buttons and Left and Right words
appear on the image, press the left mouse button on the words, and drag to the
appropriate location.
Add arrow mark : Select Arrow mark, press the left mouse button on the
image, drag to draw an arrow from the start position, and release the left mouse button
till completed. Click right to cancel;
Add text mark : Select text mark, click the mouse in the image display area,
enter text in the pop-up text box, and click OK. The text entered is displayed in the
specified location.
Delete mark : Select Delete mark on the toolbar, press the left mouse button
on the image, and click the mark to delete. Click the right mouse button to cancel;
Set the default window width / level for acquisition. See details as Preferences;
Change window width / level in time of acquisition. See details as Image acquisition;
Change window width / level in time of playback. See details as Image playback;
Adjust the window width and level: move your mouse over to screen of image
display, press the right mouse button and hold it till it turns into the state . Slide
on the screen, repeat this action, observe the image on the screen until you get the
satisfied window width and level. The values will be displayed in the W and L text
boxes in the playback area, and also in the four corners of image display screen. The
specific location of information display relates to the set image location;
Rotate left and right : click the button Rotate left or right for image
rotation.
Rotate up or down : Click the button Rotate up or down for image rotation.
Image rotation : Click Rotate to rotate the image 90 degrees to the right.
ROI (Region Of Interest) : Select ROI, click the left mouse button in the
image ROI area, drag the mouse to the appropriate location, left click again. A
regional frame appears on the image, and the suitable window width and level will be
calculated. Click the right mouse button to cancel;
Image zoom and roam , : Select Zoom, and the mouse becomes .
Scroll up the mouse wheel in the image display area to zoom out current image. Or
scroll down to zoom in. Press the left mouse button in the image display area to turn
the mouse to . Drag the image on the screen to realize image roam. Click the
right mouse button to cancel. Or select Roam on the toolbar;
Cut : Select Cut (same as ROI). After it appears, the image outside the
regional frame is cut. Click the right mouse button to cancel;
Recover image :Recover image to the original size, position, and grayscale
image.
32
Js0114.01 WD-ACQUIRE DR Image Acquisition and Processing
Click the button to pop up the dialog box Image processing, as shown:
Figure 5.5
Processing tool area is to deal with the current image, such as window width, window
level, rotation, negative image, and enhancement.
Select image processing at the top of interface: After shooting, some images of exam
programs can be dealt with in multiple ways.
Save the current image processing parameters: Apply the current image processing
parameters to “Current exam program” or “Any exam program” or “All exam
programs of current exam sub-class”.
Apply image: Apply the current image processing parameters to current image.
Restore initial value of the type: Restore the initial image processing parameters.
34
Js0114.01 WD-ACQUIRE DR Image Acquisition and Processing
Multiple printers can be set, but only one can be used for printing. Relevant
configuration items are described below.
Printer preferences:
Printer name: identify the current parameter configuration group. It can be named at
will, but not empty and can not be the same as others;
Local AE Title: Indicates the name of local application entity;
Remote AE Title: Indicates the printer name. Note that local and remote AE Titles
must be provided by the printer.
IP Address: that of printer host;
Port: that of printer;
Print mode parameter configuration:
Print copies: default film print copies.
Camera configuration info: Provided by the camera. Mainly refer to parameters ID of
printers, or some specific parameters, which is separated by backslash \ \.
Smooth type: depends on the type of amplification. When it is CUBIC, this set is
valid, and otherwise invalid. The contents are provided by the camera.
Film direction: Film print direction. PORTRAIT means vertical, and LANDSCAPE,
horizontal.
Film Size: Click the button to pop up a dialog box as shown in Figure 8.8, where the
film type can be added, edited, and deleted.
Print priority: HIGH: high priority; MED: medium priority; and LOW: low priority.
Film media: Clear Film, Blue Film, and Paper.
Zoom type: CUBIC amplification method; in this case, the smooth type is valid;
BILINER bilinear interpolation method; REPLICATE pixel replication method (least
effective); NONE: no method is used.
Film session label: available for camera node, to identify which node with the print
request.
Min density: recommended not enabled, min print gray of the current camera;
Max density: recommended not enabled, max print grayscale of the current camera.
Null means default camera setting;
36
Js0114.01 WD-ACQUIRE DR Image Acquisition and Processing
Print pixel bits: 8bit or 12bit. The current version does not support 12bit.
38
Js0114.01 WD-ACQUIRE Diagnostic Report
2. Features
Functions of diagnostic report include:
1 WYSIWYG report writing mode. Font, color, and size are adjustable.
2 A wealth of diagnosis lexicon to minimize the report writing time.
3 Customizable report style.
4 Integrated report of graphics and text.
5 Report printing.
3 Click the up and down arrow buttons for paging; click left to select an image (the
currently selected image is framed in red). Click Delete to delete the selected
image to select.
Click the main navigation bar button on the right to enter the interface
Diagnostic report.
In the Diagnostic report interface, the image selected is shown on the report, as shown
below.
Report content
Report content is shown here. For the editable entry, the content is allowed to edit
(such as diagnostic description). If the entry isn’t editable, then it isn’t allowed to edit
(such as patient name).
40
Js0114.01 WD-ACQUIRE Diagnostic Report
LANDSCAPE.
④ Empty report. Empty the image and editable entry in the current
report.
⑥ Zoom in and out. Zoom in and out the image in the report. In the report
image area, hold down the left mouse button and drag left to reduce the image and
drag right to enlarge.
⑦ Roam. In the report image area, hold down the left mouse button for
image roaming.
⑿ Help.
42
Js0114.01 WD-ACQUIRE Preferences
1. Preferences Interface
In the main interface, click System Configuration to switch to the system
configuration page, where preferences can be set, including MWL \ MPPS, save \
confirm (PACS), print, system info display, user management, playback setting and
Apr edit.
1) Worklist configuration
As shown in Figure 8.1, only one group Worklist service can be set; service name
should be different. Items marked with * are required in the configuration.
In setting interface, terms are as follows,
44
Js0114.01 WD-ACQUIRE Preferences
2) Default interface
Load data table. The first line of data table is selected by default. Name, local AET,
remote AET, and IP data of the selected row are displayed. Add, Edit, Delete, and
Verify are available, Save and Cancel are unavailable, and name, local AET, remote
AET, IP, etc. are in a non-editable state.
If there is no data in the data table, then name, local AET, remote AET, IP, etc. are
empty.
3) New
1 Fill in the configuration according to a variety of meanings of the above
configuration, click New, and then name, local AET, remote AET, and IP are
empty, Add, Edit, and Delete are unavailable, and Save, Cancel, and Verify are
available,
2 Enter name, local AET, remote AET, IP and other data.
3 Click Save, and name, local AET, remote AET, and IP are not editable. Add a row
of data to data table and select the row, then Add, Edit, Delete, and Verify are
available, Save and Cancel are unavailable.
4 Click Cancel to restore the previous state of the selected row.
4) Delete
1 Select the row to edit, then name, local AET, remote AET, IP, etc. are non-
editable, Add, Edit, and Delete are available, and Save, Cancel, and Verify are
unavailable.
2 Click Delete to pop up a dialog box reading “Are you sure to delete?”. If yes,
delete the row of data. If no, restore the state.
5) Edit
1 Select the row to edit, click Edit, and then name, local AET, remote AET, IP, etc.
are editable, Add, Edit, and Delete are unavailable, and Save, Cancel, and Verify
are available.
2 Edit name, local AET, remote AET, IP and other data.
3 Click Save, and name, local AET, remote AET, IP, etc. are in a non-editable state.
The data of the selected row are updated, Add, Edit, Delete, and Verify are
available, and Save and Cancel are unavailable.
4 Click Cancel to restore the previous state of the selected row.
6) Verify
Select the configuration to verify, click Verify, and then the interface is pending. After
Figure 7.2 Connection Failed dialog box Figure 7.3 Successful connection dialog box
Query configuration:
Query interval:
Max records per query:
Requestor mapping: Since tags of requesting program of different servers are
inconsistent, the desired exam program is obtained by Tags. Where 0 stands for
“description of requesting program”, 1 for “pre-execution steps”, 2 for “encoding
value of requesting protocol”, and 3 for “encoding value of pre-execution”.
46
Js0114.01 WD-ACQUIRE Preferences
Query:
Pre-AE Title: is to filter the records only sent to the device, as the number of same
device in a hospital differs. For example, in hospital A, there are two DR devices: one
by Wandong and another by manufacturer B. For exams conducted by Wandong DR
device, pre-AE Title can be used for identification.
Exam device: To find out what kind of device from Worklist service. Separate
multiple devices by \ \. For example, if the device supports DR and gastrointestinal
examination, then fill in DX \ \ RF.
Fill in query interval, single query records, attempt frequency, request an application,
pre-AET and other information.
Click Save to save the information; Click Cancel to restore query interval, single
query records, attempt frequency, request an application, pre-AET and other
information, which are unavailable, Edit and Restore Default are available, and Save
and Cancel are unavailable.
Click Restore Defaults, and then query interval, single query records, attempt
frequency, request an application, pre-AET and other information are restored to the
original settings.
Dicom storage can be configured with multiple sets; but of different names. Items
marked with * are required. Relevant configuration items are described below.
Remote AE Title: indicates the name to provide Dicom storage service. Note that both
local and remote AE Titles must be provided by the service provider.
Timeout: means the time period after not receiving corresponding requests in local
connection, the server side disconnects the attempt;
2) Default interface
48
Js0114.01 WD-ACQUIRE Preferences
In the interface of sending server, load and display data table . The first line of data
table is selected by default. Name, local AET, remote AET, IP, port, character
encoding, priority, timeout, enable, main server, and other data are listed in the first
row, and in a non-editable state, Add, Edit, Delete, and Verify are available, and Save
and Cancel unavailable.
Default sending method: While configuring multiple servers, send to master server by
default, or to all servers enabled.
50
Js0114.01 WD-ACQUIRE Preferences
1) Default interface
Enter the interface; the display font setting is selected by default. Load data table, and
largest sub-grid, font, and pound are in the first row. Largest sub-grid, font name, font
size, and.. are unavailable, single-box largest font setting, film font setting, data table
and Edit and Default are available, Save and Cancel are unavailable.
Click Edit, largest sub-grid, font name, font size, and .. becomes available, Edit and
Restore default are in an unusable state, and Save and Cancel are available.
Select font size and other information.
Click Save to save; click Cancel to restore the previous state; largest sub-grid, font
name, font size, and .. are available, Edit and Restore default are available, and Save
and Cancel are unavailable.
1) Default interface
In the interface, load all the available information. Location and buttons >>, >, <, <<,
Up, and Down are unavailable, Edit and Restore Default are available, and Save and
Cancel are unavailable.
Click Edit, location and buttons >>, >, <, <<, Up, and Down are available, Edit and
Restore Default are unavailable, and Save and Cancel are available.
Click Save to save; click Cancel to restore the previous state; location and buttons >>,
>, <, <<, Up, and Down are unavailable, Edit and Restore Default are available, and
Save and Cancel are unavailable.
52
Js0114.01 WD-ACQUIRE Preferences
① Click “Modify”;
② Select to ensure whether shows ruler, whether the ruler is hollow;
③ Modify ruler width, scale length and text position;
④ Set up scale calibration for RF and DX images;
⑤ Click “OK” to save current modification.
54
Js0114.01 WD-ACQUIRE Preferences
The whole operation process is divided into four levels by permission. (Permission
levels can be edited and added. See details as User group management): super
permission, management-level permission, operation-level permission, and browse-
level permission. System management group and system default group can not be
deleted.
All functions include Delete image, APR configuration, report, write to VCD or DVD,
user management, print film, camera configuration, and DICOM storage permission.
56
Js0114.01 WD-ACQUIRE Preferences
Figure 7.15 Relevant info of acquisition Figure 7.16 Relevant info of registration
interface interface
1) Default interface
Load the tree graph of exam sub-class, exam class, and program. The right are two
interfaces: one is exam class, and the other is display program. Select exam sub-class
by the selected node. Load the interface to display exam class, select exam class or
program to display the program interface.
The first node of the tree is selected by default. According to the first node (exam sub-
class), load the all exam classes to data table. The first row is selected by default.
Name, local description, exam class, exposure frequency, and whether to display
correspond to the first row of data, and in a non-editable state. Add, Edit, Delete are
available; and Save and Cancel is unavailable.
58
Js0114.01 WD-ACQUIRE Preferences
Enter name, local description, exam class, exam sub-class, and whether to display, and
default generator.
Click Save, name, local description, exam class, exam sub-class, and whether to
display, and default generator becomes non-editable. Add a row of data to data table
and select it, and add node in the tree. Add, Edit, Delete are available, and Save and
Cancel are unavailable.
Edit name, local description, exam class, exam sub-class, and whether to display, and
generator.
Click Save, and name, local description, exam class, exam sub-class, and whether to
display, and generator become non-editable. The data selected of data table are
updated, and the tree is also updated. Add, Edit, Delete are available, and Save and
Cancel are unavailable.
A body shape, body part, and projection method can be selected for an exam sub-
program, which exists in body shape table, body parts table, and projection method
table.
60
Js0114.01 WD-ACQUIRE Preferences
Click Edit in Preferences, and then Edit is unavailable. Save is available, and Left,
Right, Middle, as well as - and + of kv, MA, and MS adjustments are all available.
Adjust kv, MA, and MS parameters, and wait for approval of hardware.
Click Save in Preferences. Parameters are successfully saved in database. Edit is
available. Save is unavailable, and Left, Right, Middle, as well as - and + of kv, MA,
and MS adjustments are all unavailable.
4) Body parts
Refer to exam program to Add, Edit, and Delete body parts.
5) Projection method
Refer to exam program to Add, Edit, and Delete projection method.
6) Image processing
Refer to exam program to Add, Edit, and Delete image processing.
Image processing parameters
Gop:
int nWidth=3009,nHeight=3009;
unsigned short* Xlive = new unsigned short[nWidth*nHeight];
CLutGop * XBalance=new CLutGop();
BOOL result;
long rwnum;
if(flive!=NULL)
{
rwnum=fread(Xlive,nWidth*nHeight*sizeof(unsigned short),1,flive);
if(rwnum==-1)
return 0;
fclose(flive);
}
else
{
return 0;
XBalance->ParameterTrans(0.5,0.5,0.5,0.5,0.5);
result=XBalance->DoFlut(Xlive,nWidth,nHeight);
if(!result)return 0;
result=XBalance->DoGop(Xlive,nWidth,nHeight);
if(!result)return 0;
delete XBalance;
delete [] Xlive;
return 1;
For specific algorithm debugging, edit the curve in the DR playback interface.
2.8 IP Configuration
62
Js0114.01 WD-ACQUIRE Preferences
Appendix A
Explanation of Labels and Graphic
Symbols
64
Js0114.01 WD-ACQUIRE Explanation of Labels and Graphic Symbols
1. Product Nameplate
(Power) on
4
(Power) off
5
Small focal point
6
Large focal point
7
Wait
8
Protective grounding
10
N Neutral line
11
L Phase symbol
12
13 Wandong trademark