Professional Documents
Culture Documents
Window
12" Afghan
Square
© Heather C Gibbs 2015.
Materials:
Yarn: Weight #4
Gauge:
Size: 12 inch x 12 inch / 30.5cm x 30.5cm
7 tr/dc = 2 inches / 5 cm
Rnd 9: With a sl st attach YARN A to any ch 2 Rnd 12: With a sl st attach YARN D to any ch 2 sp
corner; ch 2 (counts as first htr/hdc), 1 htr/hdc in corner; ch 1, 1 dc/sc in same sp, ch 2, 1 dc/sc in
same ch 2 corner, ch 2, 2 htr/hdc in the same ch 2 same sp, * 1 dc/sc in the next 9 sts, ** 1 htr/hdc in
corner * miss next st, 1 htr/hdc in the next 26 sts, [2 the next st, 1 dc/sc in the next st ** repeat from **
htr/hdc, ch 2, 2 htr/hdc in the next ch 2 corner], * to ** 10 times, 1 dc/sc in the next 8 sts, [1 dc/sc, ch
repeat from * to * twice, miss next st, 1 htr/hdc in 2, 1 dc/sc in the next ch 2 sp] * repeat from * to *
the next 26 sts, then finish off with an invisible join to twice, then 1 dc/sc in the next 9 sts, next repeat
top of 1st ch 2 to join and weave in ends. (120 sts ** to ** 10 times, 1 dc/sc in the remaining 8 sts,
+ (4x) ch 2 sps). finish off with an invisible join to top of 1st dc/sc to
join and weave in ends. (156 sts).
Rnd 10: With a sl st attach YARN D to any ch 2
corner; ch 3 (counts as first tr/dc), 1 tr/dc in same ch This square will need blocking to pull it into the
2 corner, ch 2, 2 tr/dc in the same ch 2 corner * skip 12 inch x 12 inch square;
the first st, 1 tr/dc in the next 4 sts, ** ch 1, skip
next st, 1 tr/dc in next st ** repeat from ** to ** 10 Blocking afghan squares:
times, 1 tr/dc in the next 3 sts, then [2 tr/dc, ch 2, 2
tr/dc in the next sp], * repeat from * to * twice, then To steam block an afghan square pin the square
skip the first st, 1 tr/dc in the next 4 sts, next repeat evenly on a flat surface. Set your steam iron (or hand
** to ** eleven times, 1 tr/dc in the remaining 3 sts, held steamer) on the lowest setting that will produce
then finish off with an invisible join to top of 1st ch 3 steam. Once you have a good steam going, hold the
to join and weave in ends. to join. (88 sts + (44x) iron or steamer close to the crochet and work in a
ch 1 sps and (4x) ch 2 sps). circular motion over the entire piece until every inch
is evenly dampened. DO NOT touch the iron on the
Rnd 11: With a sl st attach YARN A to any ch 2 yarn! If you find that you must lightly press the
corner; ch 3 (counts as first tr/dc), 1 tr/dc in same ch square cover it with a cloth first to protect the yarn
2 corner, ch 2, 2 tr/dc in the same ch 2 corner * 1 tr/ from the hot metal plate. Allow the pieces to dry
thoroughly before unpinning.
© Keep Calm and Crochet On U.K. 2014
3
Invisible join
The last st of your work (where relevant) should be finished off using the invisible join method:
After the last stitch is completed do not join; cut your yarn and pull the tail all the way through
the stitch
Then using a hook or a yarn needle thread insert under the loops of the stitch you wish to join
to. Pull yarn through gently.
Then, insert your hook or needle into the centre of the last stitch. Pull yarn through gently and
weave in ends as usual.