Professional Documents
Culture Documents
Iso 4950 2 1995
Iso 4950 2 1995
STANDARD
Second edition
1995-08-I 5
Part 2:
Products supplied in the normalized or controlled
rolled condition
iTeh STANDARD PREVIEW
(standards.iteh.ai)
Produits plats en acier ;i hau te limite d Was ticit
Part 2: Produits livr& ;i Mat normal& ou de laminage contrM
ISO 4950-2:1995
https://standards.iteh.ai/catalog/standards/sist/4f70db80-e1c3-4432-98b1-
9c2b9dc8b4b8/iso-4950-2-1995
Reference number
IS0 4950-2: 1995(E)
IS0 4950-2: 1995(E)
Foreword
IS0 (the International Organization for Standardization) is a worldwide
federation of national standards bodies (IS0 member bodies). The work of
preparing International Standards is normally carried out through IS0
technical committees. Each member body interested in a subject for which
a technical committee has been established has the right to be
represented on that committee. International organizations, governmental
and non-governmental, in liaison with ISO, also take part in the work. IS0
collaborates closely with the International Electrotechnical Commission
(IEC) on all matters of electrotechnical standardization.
This second edition cancels and replaces the first edition (IS0 4950-2:
1981), which has been technically revised.
ISO 4950-2:1995
https://standards.iteh.ai/catalog/standards/sist/4f70db80-e1c3-4432-98b1-
9c2b9dc8b4b8/iso-4950-2-1995
IS0 4950 consists of the following parts, under the general title High yield
strength flat steel products:
0 IS0 1995
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced
or utilized in any form or by any means, electronic or mechanical, including photocopying and
microfilm, without permission in writing from the publisher.
International Organi zation for Standardiza tion
Case postale 56 l CH-12 11 Geneve 20 0 Swi tzerland
Printed in Switzerland
INTERNATIONAL STANDARD o Is0 IS0 4950-2:1995( E)
1) Plates produced by controlled rolling may be subject to deterioration of their properties if they are subsequently hot formed.
1
IS0 4950-2: 1995(E) 0 IS0
DD 0,18 0,9to 1,6 0,50 0,030 0,030 0,015to 0,060 0,02 to 0,lO 0,020 0,02to 0,20 0,25 0,30 0,lO 0,35
E355 E 0,18 0,9to 1,6 0,50 0,025 0,025 0,015 to 0,060 0,02 to 0,lO 0,020 0,02 to 0,20 0,25 0,30 0,lO 0,35
cc 0,20 1,Oto 1,7 0,50 0,040 0,040 0,015to 0,060 0,02 to 0,20 0,020 o,o*to 0,20 0,70 I,0 0,40 0,70
E460 DD 0,20 1,oto 1,7 0,50 0,030 0,030 0,015to 0,060 0,02to 0,20 0,020 o,o*to 0,20 0,70 1,o 0,40 0,70
E 0,20 1,oto 1,7 0,50 0,025 0,025 0,015to 0,060 0,02 to 0,20 0,020 o,o*to 0,20 0,70 1,o 0,40 0,70
1) As the chemical composition influences the welding characteristics, if the purchaser so requests, the producer shall, at the time of the
order being placed, indicate the type of steel which he will supply and the maximum values or the range of the alloying elements which
will be used in that steel.
2) For products of thickness up to and including 6 mm, the manganese content may be reduced by 0,2 % (m/m).
3) The steels shall contain, in the percentage indicated in the table, at least one of the grain-refining elements. If these elements are used
in combination, the content for at least one of them shall be not less than the specified minimum value.
4) By agreement at the time of ordering, the maximum copper content may be 0,30 % (m/m).
2
0 IS0 IS0 4950-Z: 1995(E)
Annex A
(informative)
The values given in table A.1 . apply to qualities DD Unless otherwise agreed, the impact energy values
and E (regardless of grade). shall be tested at
For plates and strip, the values in the longitudinal and - 20 “C for steel of quality DD,
transverse directions apply. For wide flats, only the
longitudinal direction values apply unless otherwise - 50 “C for steel of quality E.
agreed at the time of enquiry and order.
Table A.1 - Minimum values of impact energy for products of thickness 10 mm < e < 150 mm
Longitudinal
iTeh STANDARD PREVIEW
39 43 47 51 55
DD
Transverse
(standards.iteh.ai)
21 24 31 31 31
KS 77.140.50
Descriptors: i ron and steel products, structural stee Is, high yield strength steels, hot-rolled products, metal plates, wide strips, wide flats,
specifications, mecha nical proper-ties, chemical corn position, grades (quality), deli very condition.
Price based on 4 pages