Professional Documents
Culture Documents
I. PILING ................................................................................................................ 13
I. PILING
A. TIMBER PILES
1. Bakau Piles
Supply and drive bakau pile
a) 75mm diameter ne 5.00m long No 19.50
b) 75mm diameter 5.00 - 10.00m long, including mild steel
pipe sleeves No 26.15
2. Mattress Piles
Supply and lay bakau roller
a) 75mm diameter m 4.05
B. CONCRETE PILES
C. STEEL PILES
1. Isolated Piles
Supply and drive steel 'H' piles complying with BS EN 10029, with corrosion protection
including extension by weld jointing
a) size 203 x 203mm x 53.57 kg/m m 164.55
b) size 254 x 254mm x 62.50 kg/m m 191.70
c) size 305 x 305mm x 78.87 kg/m m 233.65
d) size 330 x 330mm x 108.63 kg/m m 316.15
e) size 356 x 356mm x 132.44 kg/m m 373.90
D. BORED PILES
3. Steel Casing
a) Supply and drive steel casing to be left in for bored piles kg 3.40
E. MICROPILES
1. Bored Micropiles
Supply and install micropiles
a) 150mm diameter m 259.90
b) 200mm diameter m 295.15
c) 250mm diameter m 321.85
Cutting of pile to the required level including welding of the bearing plate
d) generally No 270.15
2. Driven Micropiles
Supply and drive steel micropiles complete with cement grouting to centre void
a) 114mm diameter (with working capacity of 20 ton each) m 110.50
Cutting of pile to the required level including welding of the bearing plate
b) Generally No 118.55
F. SUNDRIES
1. Pile Tests
Test loading of piles with the Kentledge reaction system including casting and
subsequent removal of temporary pile cap
a) generally t 90.30
II. EXCAVATION
A. SITE CLEARANCE
2. Remove Trees
Cut tree including grubbing up roots, filling voids and disposal of materials off site
a) 600 - 1000mm girth No 347.70
b) 1000 - 1500mm girth No 585.30
c) 1500 - 2000mm girth No 911.65
d) 2000 - 2500mm girth No 1,136.95
B. GENERAL EXCAVATION
1. Pit/Trench Excavation
Excavate to form trench, commencing from reduced level
a) ne 1.00m deep and cross sectional area ne 0.50m 2 m 12.35
Excavate to form pit or trench, commencing from reduced level
b) ne 2.00m deep m3 30.60
c) 2.00 - 4.00m deep m3 36.40
d) 4.00 - 5.00m deep m3 40.95
2. Basement Excavation
Excavate to form basement, commencing from reduced level
a) ne 2.00m deep m3 27.20
b) 2.00 - 4.00m deep m3 32.25
3. Cutting
Excavate to form embankment, commencing from reduced level
a) generally m3 21.10
4. Break Up Obstructions
Extra over excavation for breaking up obstruction using mechanical means
a) brickwork and blockwork m3 42.65
b) mass concrete m3 75.65
c) reinforced concrete m3 96.10
d) rock m3 140.20
5. Break Up Surface Obstructions
Break up surface pavement
a) tarmacadam surface m3 32.00
b) mass concrete m3 52.10
c) reinforced concrete m3 100.70
d) brickwork and blockwork m3 48.45
C. FILLING
1. Backfilling
Backfilling around trench, column base, pile cap, foundation beam and pier hole
a) excavated material obtained within the site m3 8.00
b) earthfilling obtained from contractor's own source m3 18.80
D. DISPOSAL
1. Excavated Material
Remove excavated material off site
a) for suitable excavated material m3 22.50
b) for unsuitable excavated material m3 42.50
1. Lean/Mass Concrete
Lean or Mass concrete complying with BS EN 1992-1-1
a) grade 10 m3 158.35
b) grade 15 m3 160.75
c) grade 20 m3 166.50
3. Waterproofed Concrete
Waterproofed concrete complying with BSEN 1992-1-1 with approved waterproofing
compound
a) grade 30 m3 217.95
b) grade 35 m3 227.50
B. REINFORCEMENT
1. Bar Reinforcement
Mild steel bar reinforcement complying with SS 560
a) 6mm diameter kg 1.90
b) 10mm diameter kg 1.90
c) 13mm diameter kg 1.90
d) 16mm diameter kg 1.85
e) 20mm diameter kg 1.85
f) 22mm diameter kg 1.85
g) 25mm diameter kg 1.85
h) 28mm diameter kg 1.85
i) 32mm diameter kg 1.85
High tensile steel bar reinforcement complying with SS 560
j) 10mm diameter kg 1.75
k) 13mm diameter kg 1.75
l) 16mm diameter kg 1.75
m) 20mm diameter kg 1.75
n) 22mm diameter kg 1.75
2. Fabric Reinforcement
Welded steel fabric reinforcement complying with SS 561 and well lapped (measured
nett)
a) Reference No A5 m2 7.35
b) Reference No A6 m2 8.95
c) Reference No A7 m2 10.00
d) Reference No A8 m2 11.30
e) Reference No A9 m2 13.30
f) Reference No A10 m2 14.40
g) Reference No B5 m2 10.55
h) Reference No B6 m2 11.70
i) Reference No B7 m2 12.65
j) Reference No B8 m2 14.65
k) Reference No B9 m2 16.70
l) Reference No B10 m2 18.05
m) Reference No B11 m2 20.55
n) Reference No B12 m2 22.85
o) Reference No B13 m2 26.10
p) Reference No D6 m2 11.05
q) Reference No D7 m2 13.65
r) Reference No D8 m2 17.25
s) Reference No D9 m2 21.20
t) Reference No D10 m2 24.30
u) Reference No D11 m2 29.20
v) Reference No D12 m2 33.60
C. PRECAST CONCRETE
1. Kerb or Divider
Precast concrete kerb or divider in Grade 25 concrete including laying in alignment
and finishing fair on all exposed surfaces
a) 125 x 250mm Type K2A Kerb m 17.00
b) 125 x 275mm Type K2B Kerb m 17.25
c) 150 x 300mm Type D1 Divider m 16.45
Extra over Type K2A/B Kerb with slot hole
d) generally No 4.30
2. Cover Slab
Precast concrete Grade 30 cover slab all as detailed in SDRE – Drains & Culverts
a) 640 x 270 x 75mm No 11.45
D. FORMWORK
1. Sawn Formwork
Sawn formwork to in-situ concrete including strutting not exceeding 3.5m high
a) curved surface m2 51.50
b) plain surface m2 43.95
2. Wrought Formwork
Wrought formwork to in-situ concrete including strutting not exceeding 3.5m high
a) curved surface m2 59.40
b) plain surface m2 53.70
3. Strutting
Extra over for strutting exceeding 3.50m high
a) Every 1.50m high m2 5.45
F. SUNDRIES
1. Expansion Joints
75mm high bitumen impregnated fibreboard joint filler
a) 12mm thick m 3.15
b) 20mm thick m 3.70
c) 25mm thick m 4.45
Polyethylene bond breaking strip to joint
d) 10mm diameter m 3.05
e) 15mm diameter m 3.40
f) 25mm diameter m 3.75
25mm wide polysulphide sealer to joint
g) 15mm deep m 18.15
h) 25mm deep m 29.30
15mm wide x 50mm deep heavy duty approved sealant
i) generally m 16.50
15mm wide x 175mm deep impregnated flexcell board
j) generally m 12.00
15mm wide x 300mm deep white rigid polyvinylchloride
crack inducer
k) generally m 18.00
Drilling of 16mm diameter holes and fill with epoxy resin
l) not exceeding 100mm length per hole 15.00
m) not exceeding 150mm length per hole 20.00
2. Trowelling
Labour trowel top surface of concrete to a smooth finish including additional cement
a) generally m2 12.00
IV. BRICKWORK
A. CLAY BRICKS
A. STRUCTURAL STEELWORK
B. METALWORK
Hot dip galvanised brace support (on one side) including post, spacer, brace with mild
steel plates welded, set in and including concrete foundation, all necessary excavation,
disposal of excavated material as per SDRE – Guardrails
c) 150 × 150 × 6mm SHS Set 453.40
D. RAILING
E. GRATING
1. Pedestrian Grating
Fabricate, supply and install standard hot dip galvanised m.s pedestrian hinged grating
and frame including 3 mm thick chequered plate (spot welded) to flush with footpath
level as detailed in SDRE - Gratings & Manhole Covers (removal of existing grating to
be measured separately)
a) Size 700mm x 850mm No. 209.10
b) Size 850mm x 1000mm No. 299.20
c) Other sizes m2 347.65
3. Vehicular Grating
Fabricate,supply & install standard hot dip galvanised m.s vehicular hinged grating
and framed as detailed in SDRE-Gratings & Manhole Covers (removal of existing
grating to be measured separately).
a) generally for drains m2 1,284.35
b) generally for manholes m2 1,256.60
4. Aluminium Rung
300 x 230mm aluminium rung as per SDRE – Drains & Culverts fixed to concrete wall
in drain including drilling and grouting with cement mortar (1:3)
a) 25mm diameter No 22.75
F. SURFACE TREATMENT
2. Plain Paving
Cement and sand (1:3) paving including trowelling smooth
a) average 20mm thick m2 16.80
b) average 25mm thick m2 18.00
c) average 32mm thick m2 20.00
20mm thick cement and sand (1:3) skirting with splayed or rounded top edge and
coved bottom including trowelling smooth
d) 100mm high m 7.00
e) 150mm high m 7.75
3. Hardened Paving
25mm thick cement and sand (1:3) paving mixed with hardener including trowelling
smooth
a) light duty non-metallic hardener (3kg per m2) m2 30.65
b) heavy duty non-metallic hardener (7kg per m2) m2 40.75
4. Granolithic Paving
Granolithic aggregate paving consisting of cement, sand and granite chippings of 5mm
gauge (2:1:5) set out in panels with 15 x 15mm deep recessed joints laterally at 1.20m
centres including scrubbing to produce exposed aggregate finish
a) 25mm thick m2 38.20
b) 32mm thick m2 39.50
c) 40mm thick m2 42.15
VII. PAINTING
A. PAINTING
3. Metal Surfaces
Painting metal surface
a) one coat anti-rust paint, one undercoat and two coats of
aluminium paint m2 15.45
b) one coat of zinc chromate primer, one undercoat and
two finishing coats of synthetic enamel paint m2 15.25
4. Road Marking
One coat of 1.5mm thick thermoplastic paint on road pavement as per SDRE – Road
Markings & Signs
a) 100mm wide line m 2.45
b) 150mm wide line m 3.85
c) 200mm wide line m 5.25
d) 300mm wide line m 6.10
e) exceeding 300mm wide line m2 36.00
One coat of 3.00mm thick thermoplastic paint on road pavement as per SDRE –
Cycling Path
l) footprint logo of size 600mm x 720mm no. 89.50
m) bicycle logo of size 850mm x 650mm no. 166.40
A. DRAINAGE WORK
1. Drain Excavation
Excavate trench minimum 340mm wide for 100mm diameter pipe, not exceeding
2.00m deep including backfilling and disposal of surplus excavated material
a) average 600mm deep m 17.05
b) average 1000mm deep m 24.25
c) average 1500mm deep m 50.70
Excavate trench minimum 490mm wide for 150mm diameter pipe including temporary
supports, backfilling and disposal of surplus excavated material
d) ne 2.00m deep, average 1.50m deep m 57.95
e) 2.00 - 4.00m deep, average 3.00m deep m 92.60
2. Benchings & Haunchings
125mm thick concrete (Grade 35) bed under 250mm UPVC scupper pipe including
haunching to half height of pipe carried up and splayed tangentially and all necessary
formwork, reinforcement and lean concrete
a) 450mm wide, under 250mm diameter scupper pipe m 51.40
1. UPVC Pipes
Heavy duty unplasticised polyvinyl chloride Class C subsoil pipes 3/4 perforated
a) 100mm diameter m 31.85
b) 150mm diameter m 52.15
2. Filling Materials
a) Graded stone 20mm size m3 126.00
3. Drainage Layer
a) Geocomposite drainage layer as per SDRE – Drains &
Culverts m2 10.65
1. Pipe Culverts
Precast concrete pipe culverts Class 'L' complying with SS 183 butt jointed with
cement and sand (1:1) mortar
a) 300mm diameter m 81.70
b) 450mm diameter m 120.00
c) 600mm diameter m 175.45
d) 750mm diameter m 268.90
e) 900mm diameter m 352.90
f) 1,050mm diameter m 406.10
g) 1,200mm diameter m 487.90
h) 1,350mm diameter m 552.60
i) 1,500mm diameter m 692.65
Precast concrete pipe culverts Class 'M' complying with SS 183 butt jointed with
cement and sand (1:1) mortar
j) 300mm diameter m 92.90
k) 450mm diameter m 156.60
l) 600mm diameter m 232.00
m) 750mm diameter m 299.00
n) 900mm diameter m 407.50
o) 1,050mm diameter m 476.75
p) 1,200mm diameter m 566.90
q) 1,350mm diameter m 657.90
2. Composite Channels
Precast concrete composite channel or block drains laid to even falls and jointed in
cement and sand (1:3) mortar
a) Type C1 m 10.30
b) Type C2 m 11.15
c) Type C3 m 12.80
d) Type C4 m 13.55
e) Type C5 m 15.45
f) Type C5A m 14.70
g) Type C6 m 16.70
h) Type C7R m 36.15
i) Type C7R1 m 38.30
j) Type C7A m 37.65
k) Type C7B m 35.35
l) Type C8 m 63.75
m) Type C8A m 47.85
n) Type C8B m 75.30
o) Type B1 m 37.30
p) Type B2 m 42.60
q) Type B3 m 84.75
Precast concrete channel laid in precast 'U' drain base sections or precast concrete
culverts including concrete grade 20 benching
r) Type C3 m 20.00
4. Weepholes
Supply and fix UPVC pipe to SS141 as weephole
a) 65mm diameter ne 300mm long No 3.80
b) 65mm diameter exc 300mm long m 5.80
c) 75mm diameter ne 300mm long No 4.10
d) 75mm diameter exc 300mm long m 6.70
E. SUNDRIES
2. Sump
Precast concrete sump for sub-soil drain including proper connections, concrete
benching and precast concrete cover slabs, internal size
a) 550 x 550 x 1300mm No 523.25
A. PAVEMENT
1. Sub-base
Supply and lay Sub-base material
a) generally m3 51.00
2. Base Course
Supply and lay Coarse granite aggregate (crusher-run) base course and blinded with
fine aggregate
a) generally m3 137.80
3. Asphalt Concrete
Supply and lay hot-mix asphalt concrete base, binder or wearing course including
soluble bitumen
a) mix-specification type B1 ton 116.25
b) mix-specification type B1G ton 121.25
c) mix-specification type W1 ton 112.20
d) mix-specification type W3 ton 112.20
e) mix-specification type W3B ton 112.20
f) mix-specification type Open-graded ton 141.20
Supply and lay hot-mix asphalt concrete binder course mix type B1 including soluble
bitumen
g) 50mm (consolidated) thick m2 14.30
h) 75mm (consolidated) thick m2 21.20
i) 90mm (consolidated) thick m2 25.15
j) 120mm (consolidated) thick m2 33.40
Supply and lay hot-mix asphalt concrete binder course mix type B1G including soluble
bitumen
k) 75mm (consolidated) thick m2 19.75
l) 90mm (consolidated) thick m2 23.65
m) 120mm (consolidated) thick m2 31.60
Supply and lay hot-mix asphalt concrete wearing course mix type W3B including
soluble bitumen
n) 25mm (consolidated) thick m2 7.35
o) 40mm (consolidated) thick m2 11.70
p) 50mm (consolidated) thick m2 14.30
Supply and lay hot-mix open graded asphalt concrete special road mix including
modified binder
q) 25mm (consolidated) thick m2 8.00
r) 40mm (consolidated) thick m2 12.25
s) 50mm (consolidated) thick m2 15.30
A. STREET FURNITURE
1. Directional Signs
Single-face directional signs comprising aluminium sheeting 14SWG laminated with
approved reflective sheeting including all the required size of letters, numbers, logo(s)
and all necessary backings, welding and other types of connections as per SDRE –
Supports for Road Signs (supports to be measured separately)
a) Micro Prismatic Reflective Grade (Type IX) m2 703.00
Supports including foundation, excavation and disposal as per SDRE – Supports for
Road Signs
b) 89 x 3.2mm thk CHS cantilever support (Type A) No 882.10
c) a pair of 120 x 120 x 6mm SHS supports (Type B) No 3,997.00
d) a pair of 150 x 150 x 8mm SHS supports (Type C) No 5,426.00
e) a pair of 180 x 180 x 8mm SHS supports (Type D) No 7,186.00
f) a pair of 200 x 200 x 8mm SHS supports (Type E) No. 8,986.00
2. Traffic Signs
Single-faced silk screen traffic signs as regulatory signs, warning signs and informative
signs comprising 2mm thick aluminium sheets, approved Micro Prismatic Grade
reflective sheetings including appropriate diagrams, alphabets and numerals
(supports to be measured separately)
a) size 600 x 450mm No 156.80
b) size 600 x 600mm No 183.10
c) size 900 x 900mm No 270.90
d) other sizes m2 505.45
Supports including foundation, excavation and disposal as per SDRE – Supports for
Road Signs
e) SHS 50 x 50 x 2.3mm thick hot dipped galvanised single
post support No 351.00
Curved alignment marker comprising of 2mm thick aluminium sheets and approved
Mirco Prismatic Fluorescent Yellow reflective sheetings as per SDRE – Road Markings
and Signs
a) size 600 x 750mm (for arterial road) No 276.80
b) size 750 x 900mm (for expressway) No 394.90
B. SUNDRIES
1. Turfing
Turfing consisting of grass, size 300 x 300mm not less than 50mm thick, including
50mm thick topsoil and sludge (3:1) top dressing
a) spot turf on horizontal surface m2 8.30
b) close turf on embankment exceeding 15º from the
horizontal m2 9.90
5. Paving Slabs
Precast concrete (grade 20) paving slab jointed and pointed in cement and sand (1:3)
including 50mm thick sand bed
a) size 300 x 300 x 50mm thick m2 55.65
6. Aeration Slabs
Precast concrete aeration slab of any pattern with top soil and turfing in voids including
50mm thick sand bed
a) 65mm thick m2 46.50
b) 100mm thick m2 52.05