Professional Documents
Culture Documents
CRIMP SPECIFICATIONS
Fitting
Insertion Crimp Dial Setting
Hose Ferrule Length Die Length Crimp Diameter Approx. Actual
mm mm in
NOTE: Die and dial settings are approximate recommendations. Ferrules should be crimped with
IT01 00 the largest diameter die set available to make the ridges on the finished crimp as small as
possible. All crimp dimensions must be verified with a calibrated measuring device.
Printed: 24-Feb-23
CRIMP SPECIFICATIONS
Crimper Hose Coupling Crimp Instructions CHART NUMBER 183 REV 00
Finn-Power 110 4200 One-piece Mark the hose at a distance from the end of the hose equal to the "Insertion Length". Install the
fitting on the hose so that the mark is even with the end of the ferrule. Crimp the entire length of
32 Series the ferrule to the Crimp Diameter given in the table. Tolerance +0.1mm/- 0.2mm or + 0.004/-0.008
inches.
Fitting
Insertion Crimp Dial Setting
Hose Ferrule Length Die Length Crimp Diameter Approx. Actual
mm mm in
NOTE: Die and dial settings are approximate recommendations. Ferrules should be crimped with
IT69 00 the largest diameter die set available to make the ridges on the finished crimp as small as
possible. All crimp dimensions must be verified with a calibrated measuring device.
Printed: 24-Feb-23
CRIMP SPECIFICATIONS
Crimper Hose Coupling Crimp Instructions CHART NUMBER 179 REV 00
Finn-Power 111 P4300 One-piece Mark the hose at a distance from the end of the hose equal to the "Insertion Length". Install the
fitting on the hose so that the mark is even with the end of the ferrule. Crimp the entire length of
32 Series the ferrule to the Crimp Diameter given in the table. Tolerance +0.1mm/- 0.2mm or + 0.004/-0.008
inches.
Fitting
Insertion Crimp Dial Setting
Hose Ferrule Length Die Length Crimp Diameter Approx. Actual
mm mm in
NOTE: Die and dial settings are approximate recommendations. Ferrules should be crimped with
PUL 111 00 the largest diameter die set available to make the ridges on the finished crimp as small as
possible. All crimp dimensions must be verified with a calibrated measuring device.
Printed: 24-Feb-23
CRIMP SPECIFICATIONS
Crimper Hose Coupling Crimp Instructions CHART NUMBER 86 REV 00
Finn-Power 112 4200 One-piece Mark the hose at a distance from the end of the hose equal to the "Insertion Length". Install the
fitting on the hose so that the mark is even with the end of the ferrule. Crimp the entire length of
32 Series the ferrule to the Crimp Diameter given in the table. Tolerance +0.1mm/- 0.2mm or + 0.004/-0.008
inches.
Fitting
Insertion Crimp Dial Setting
Hose Ferrule Length Die Length Crimp Diameter Approx. Actual
mm mm in
NOTE: Die and dial settings are approximate recommendations. Ferrules should be crimped with
IT04 00 the largest diameter die set available to make the ridges on the finished crimp as small as
possible. All crimp dimensions must be verified with a calibrated measuring device.
Printed: 24-Feb-23
CRIMP SPECIFICATIONS
Crimper Hose Coupling Crimp Instructions CHART NUMBER 84 REV 01
Finn-Power 122 4200 One-piece Mark the hose at a distance from the end of the hose equal to the "Insertion Length". Install the
fitting on the hose so that the mark is even with the end of the ferrule. Crimp the entire length of
32 Series the ferrule to the Crimp Diameter given in the table. Tolerance +0.1mm/- 0.2mm or + 0.004/-0.008
inches.
Fitting
Insertion Crimp Dial Setting
Hose Ferrule Length Die Length Crimp Diameter Approx. Actual
mm mm in
NOTE: Die and dial settings are approximate recommendations. Ferrules should be crimped with
IT02 01 the largest diameter die set available to make the ridges on the finished crimp as small as
possible. All crimp dimensions must be verified with a calibrated measuring device.
Printed: 24-Feb-23
CRIMP SPECIFICATIONS
Crimper Hose Coupling Crimp Instructions CHART NUMBER 180 REV 00
Finn-Power 122 P4300 One-piece Mark the hose at a distance from the end of the hose equal to the "Insertion Length". Install the
fitting on the hose so that the mark is even with the end of the ferrule. Crimp the entire length of
32 Series the ferrule to the Crimp Diameter given in the table. Tolerance +0.1mm/- 0.2mm or + 0.004/-0.008
inches.
Fitting
Insertion Crimp Dial Setting
Hose Ferrule Length Die Length Crimp Diameter Approx. Actual
mm mm in
NOTE: Die and dial settings are approximate recommendations. Ferrules should be crimped with
PUL 122 00 the largest diameter die set available to make the ridges on the finished crimp as small as
possible. All crimp dimensions must be verified with a calibrated measuring device.
Printed: 24-Feb-23
CRIMP SPECIFICATIONS
Crimper Hose Coupling Crimp Instructions CHART NUMBER 124 REV 00
Finn-Power 114 4200 One-piece Mark the hose at a distance from the end of the hose equal to the "Insertion Length". Install the
fitting on the hose so that the mark is even with the end of the ferrule. Crimp the entire length of
32 Series the ferrule to the Crimp Diameter given in the table. Tolerance +0.1mm/- 0.2mm or + 0.004/-0.008
inches.
Fitting
Insertion Crimp Dial Setting
Hose Ferrule Length Die Length Crimp Diameter Approx. Actual
mm mm in
NOTE: Die and dial settings are approximate recommendations. Ferrules should be crimped with
IT34 00 the largest diameter die set available to make the ridges on the finished crimp as small as
possible. All crimp dimensions must be verified with a calibrated measuring device.
Printed: 24-Feb-23
CRIMP SPECIFICATIONS
Crimper Hose Coupling Crimp Instructions CHART NUMBER 178 REV 00
Finn-Power 114 P4300 One-piece Mark the hose at a distance from the end of the hose equal to the "Insertion Length". Install the
fitting on the hose so that the mark is even with the end of the ferrule. Crimp the entire length of
32 Series the ferrule to the Crimp Diameter given in the table. Tolerance +0.1mm/- 0.2mm or + 0.004/-0.008
inches.
Fitting
Insertion Crimp Dial Setting
Hose Ferrule Length Die Length Crimp Diameter Approx. Actual
mm mm in
NOTE: Die and dial settings are approximate recommendations. Ferrules should be crimped with
PUL 114 00 the largest diameter die set available to make the ridges on the finished crimp as small as
possible. All crimp dimensions must be verified with a calibrated measuring device.
Printed: 24-Feb-23
CRIMP SPECIFICATIONS
Crimper Hose Coupling Crimp Instructions CHART NUMBER 151 REV 02
Finn-Power 124 4400 One-piece Mark the hose at a distance from the end of the hose equal to the "Insertion Length". Install the
fitting on the hose so that the mark is even with the end of the ferrule. Crimp the entire length of
32 Series
PLUS the ferrule to the Crimp Diameter given in the table. Tolerance +0.1mm/- 0.2mm or + 0.004/-0.008
inches.
Fitting
Insertion Crimp Dial Setting
Hose Ferrule Length Die Length Crimp Diameter Approx. Actual
mm mm in
124 PLUS -06 4400 25 32-22 Full 24.0 0.945 2.0
124 PLUS -08 4400 31 32-26 Full 26.4 1.039 0.4
124 PLUS -10 4400 31 32-30 Full 32.6 1.283 2.6
124 PLUS -12 4400 34 32-34 Full 34.3 1.350 0.3
124 PLUS -16 4400 47 32-39 Full 42.7 1.681 3.7
124 PLUS -20 4400 54 32-45 Full 49.6 1.953 4.6
124 PLUS -24 4400 56 32-57 Full 60.3 2.374 3.3
124 PLUS -32 4400 70 32-74 Full 74.8 2.945 0.8
NOTE: Die and dial settings are approximate recommendations. Ferrules should be crimped with
IT53 02 the largest diameter die set available to make the ridges on the finished crimp as small as
possible. All crimp dimensions must be verified with a calibrated measuring device.
Printed: 24-Feb-23
CRIMP SPECIFICATIONS
Crimper Hose Coupling Crimp Instructions CHART NUMBER 91 REV 01
Finn-Power 124 4400 One-piece Mark the hose at a distance from the end of the hose equal to the "Insertion Length". Install the
fitting on the hose so that the mark is even with the end of the ferrule. Crimp the entire length of
32 Series the ferrule to the Crimp Diameter given in the table. Tolerance +0.1mm/- 0.2mm or + 0.004/-0.008
inches.
Fitting
Insertion Crimp Dial Setting
Hose Ferrule Length Die Length Crimp Diameter Approx. Actual
mm mm in
NOTE: Die and dial settings are approximate recommendations. Ferrules should be crimped with
IT09 01 the largest diameter die set available to make the ridges on the finished crimp as small as
possible. All crimp dimensions must be verified with a calibrated measuring device.
Printed: 24-Feb-23
CRIMP SPECIFICATIONS
Crimper Hose Coupling Crimp Instructions CHART NUMBER 192 REV 01
Finn-Power 124 XTC 4400 One-piece Mark the hose at a distance from the end of the hose equal to the "Insertion Length". Install the
fitting on the hose so that the mark is even with the end of the ferrule. Crimp the entire length of
32 Series the ferrule to the Crimp Diameter given in the table. Tolerance +0.1mm/- 0.2mm or + 0.004/-0.008
inches.
Fitting
Insertion Crimp Dial Setting
Hose Ferrule Length Die Length Crimp Diameter Approx. Actual
mm mm in
NOTE: Die and dial settings are approximate recommendations. Ferrules should be crimped with
IT76 01 the largest diameter die set available to make the ridges on the finished crimp as small as
possible. All crimp dimensions must be verified with a calibrated measuring device.
Printed: 24-Feb-23
CRIMP SPECIFICATIONS
Crimper Hose Coupling Crimp Instructions CHART NUMBER 193 REV 01
Finn-Power 124 XTC 5000 Two-piece Tolerance + 0.1/-0.2mm or + 0.004/-0.008 inches .
32 Series
NOTE: Die and dial settings are approximate recommendations. Ferrules should be crimped with
IT77 01 the largest diameter die set available to make the ridges on the finished crimp as small as
possible. All crimp dimensions must be verified with a calibrated measuring device.
Printed: 24-Feb-23
CRIMP SPECIFICATIONS
Crimper Hose Coupling Crimp Instructions CHART NUMBER 92 REV 03
Finn-Power 136 4400 One-piece Mark the hose at a distance from the end of the hose equal to the "Insertion Length". Install the
fitting on the hose so that the mark is even with the end of the ferrule. Crimp the entire length of
32 Series the ferrule to the Crimp Diameter given in the table. Tolerance +0.1mm/- 0.2mm or + 0.004/-0.008
inches.
Fitting
Insertion Crimp Dial Setting
Hose Ferrule Length Die Length Crimp Diameter Approx. Actual
mm mm in
NOTE: Die and dial settings are approximate recommendations. Ferrules should be crimped with
IT10 03 the largest diameter die set available to make the ridges on the finished crimp as small as
possible. All crimp dimensions must be verified with a calibrated measuring device.
Printed: 24-Feb-23
CRIMP SPECIFICATIONS
Crimper Hose Coupling Crimp Instructions CHART NUMBER 159 REV 00
Finn-Power 136 4600 One-piece Mark the hose at a distance from the end of the hose equal to the "Insertion Length". Install the
fitting on the hose so that the mark is even with the end of the ferrule. Crimp the entire length of
32 Series the ferrule to the Crimp Diameter given in the table. Tolerance +0.1mm/- 0.2mm or + 0.004/-0.008
inches.
Fitting
Insertion Crimp Dial Setting
Hose Ferrule Die Length Crimp Diameter Approx. Actual
mm in
NOTE: Die and dial settings are approximate recommendations. Ferrules should be crimped with
IT58 00 the largest diameter die set available to make the ridges on the finished crimp as small as
possible. All crimp dimensions must be verified with a calibrated measuring device.
Printed: 24-Feb-23
CRIMP SPECIFICATIONS
Crimper Hose Coupling Crimp Instructions CHART NUMBER 160 REV 00
Finn-Power 156 44/4600 One-piece Mark the hose at a distance from the end of the hose equal to the "Insertion Length". Install the
fitting on the hose so that the mark is even with the end of the ferrule. Crimp the entire length of
32 Series
PLUS the ferrule to the Crimp Diameter given in the table. Tolerance +0.1mm/- 0.2mm or + 0.004/-0.008
inches.
Fitting
Insertion Crimp Dial Setting
Hose Ferrule Die Length Crimp Diameter Approx. Actual
mm in
156 PLUS -12 4400 34 32-34 Full 35.1 1.382 1.1
156 PLUS -16 4400 47 32-39 Full 42.0 1.654 3.0
156 PLUS -20 4600 60 32-57 Full 57.0 2.244 0.0
156 PLUS -24 4600 61 32-63 Full 63.7 2.508 0.7
156 PLUS -32 4600 97 32-78 Full 78.2 3.079 0.2
NOTE: Die and dial settings are approximate recommendations. Ferrules should be crimped with
IT59 00 the largest diameter die set available to make the ridges on the finished crimp as small as
possible. All crimp dimensions must be verified with a calibrated measuring device.
Printed: 24-Feb-23
CRIMP SPECIFICATIONS
Crimper Hose Coupling Crimp Instructions CHART NUMBER 185 REV 00
Finn-Power 124 4600 One-piece Mark the hose at a distance from the end of the hose equal to the "Insertion Length". Install the
fitting on the hose so that the mark is even with the end of the ferrule. Crimp the entire length of
32 Series
PLUS the ferrule to the Crimp Diameter given in the table. Tolerance +0.1mm/- 0.2mm or + 0.004/-0.008
inches.
Fitting
Insertion Crimp Dial Setting
Hose Ferrule Die Length Crimp Diameter Approx. Actual
mm in
124 PLUS -20 4600 60 32-51 Full 53.5 2.106 2.5
124 PLUS -24 4600 61 32-57 Full 61.2 2.409 4.2
124 PLUS -32 4600 97 32-74 Full 75.5 2.972 1.5
NOTE: Die and dial settings are approximate recommendations. Ferrules should be crimped with
IT71 00 the largest diameter die set available to make the ridges on the finished crimp as small as
possible. All crimp dimensions must be verified with a calibrated measuring device.
Printed: 24-Feb-23
CRIMP SPECIFICATIONS
Crimper Hose Coupling Crimp Instructions CHART NUMBER 186 REV 00
Finn-Power 124 4200 One-piece Mark the hose at a distance from the end of the hose equal to the "Insertion Length". Install the
fitting on the hose so that the mark is even with the end of the ferrule. Crimp the entire length of
32 Series the ferrule to the Crimp Diameter given in the table. Tolerance +0.1mm/- 0.2mm or + 0.004/-0.008
inches.
Fitting
Insertion Crimp Dial Setting
Hose Ferrule Length Die Length Crimp Diameter Approx. Actual
mm mm in
NOTE: Die and dial settings are approximate recommendations. Ferrules should be crimped with
IT72 00 the largest diameter die set available to make the ridges on the finished crimp as small as
possible. All crimp dimensions must be verified with a calibrated measuring device.
Printed: 24-Feb-23
CRIMP SPECIFICATIONS
Crimper Hose Coupling Crimp Instructions CHART NUMBER 95 REV 02
Finn-Power 151 4500 One-piece Mark the hose at a distance from the end of the hose equal to the "Insertion Length". Install the
fitting on the hose so that the mark is even with the end of the ferrule. Crimp the entire length of
32 Series the ferrule to the Crimp Diameter given in the table. Tolerance +0.1mm/- 0.2mm or + 0.004/-0.008
inches.
NOTE: Die and dial settings are approximate recommendations. Ferrules should be crimped with
IT12 02 the largest diameter die set available to make the ridges on the finished crimp as small as
possible. All crimp dimensions must be verified with a calibrated measuring device.
Printed: 24-Feb-23
CRIMP SPECIFICATIONS
Crimper Hose Coupling Crimp Instructions CHART NUMBER 176 REV 00
Finn-Power 151 42/4400 One-piece Mark the hose at a distance from the end of the hose equal to the "Insertion Length". Install the
fitting on the hose so that the mark is even with the end of the ferrule. Crimp the entire length of
32 Series the ferrule to the Crimp Diameter given in the table. Tolerance +0.1mm/- 0.2mm or + 0.004/-0.008
inches.
Fitting
Insertion Crimp Dial Setting
Hose Ferrule Die Length Crimp Diameter Approx. Actual
mm in
4200-04
151 -05 23 32-16 Full 18.1 0.713 2.1
4200-06
151 -08 25 32-22 Full 22.9 0.902 0.9
4400-08
151 -10 31 32-26 Full 28.2 1.110 2.2
4400-10
151 -12 31 32-30 Full 30.8 1.213 0.8
NOTE: Die and dial settings are approximate recommendations. Ferrules should be crimped with
IT67 00 the largest diameter die set available to make the ridges on the finished crimp as small as
possible. All crimp dimensions must be verified with a calibrated measuring device.
Printed: 24-Feb-23
CRIMP SPECIFICATIONS
Crimper Hose Coupling Crimp Instructions CHART NUMBER 177 REV 00
Finn-Power 151 5000 Two-piece Tolerance + 0.1/-0.2mm or + 0.004/-0.008 inches .
32 Series
NOTE: Die and dial settings are approximate recommendations. Ferrules should be crimped with
IT68 00 the largest diameter die set available to make the ridges on the finished crimp as small as
possible. All crimp dimensions must be verified with a calibrated measuring device.
Printed: 24-Feb-23
CRIMP SPECIFICATIONS
Crimper Hose Coupling Crimp Instructions CHART NUMBER 87 REV 01
Finn-Power 141 4200 One-piece Mark the hose at a distance from the end of the hose equal to the "Insertion Length". Install the
fitting on the hose so that the mark is even with the end of the ferrule. Crimp the entire length of
32 Series the ferrule to the Crimp Diameter given in the table. Tolerance +0.1mm/- 0.2mm or + 0.004/-0.008
inches.
Fitting
Insertion Crimp Dial Setting
Hose Ferrule Length Die Length Crimp Diameter Approx. Actual
mm mm in
NOTE: Die and dial settings are approximate recommendations. Ferrules should be crimped with
IT05 01 the largest diameter die set available to make the ridges on the finished crimp as small as
possible. All crimp dimensions must be verified with a calibrated measuring device.
Printed: 24-Feb-23
CRIMP SPECIFICATIONS
Crimper Hose Coupling Crimp Instructions CHART NUMBER 122 REV 00
Finn-Power 119 4200 Skive Mark the hose at a distance from the end of the hose equal to the "Insertion Length". Install the
fitting on the hose so that the mark is even with the end of the ferrule. Crimp the entire length of
32 Series the ferrule to the Crimp Diameter given in the table. Tolerance +0.1mm/- 0.2mm or + 0.004/-0.008
inches.
Cover
Skive Crimp Dial Setting
Hose Ferrule Length Die Length Crimp Diameter Approx. Actual
mm mm in
NOTE: Die and dial settings are approximate recommendations. Ferrules should be crimped with
IT33 00 the largest diameter die set available to make the ridges on the finished crimp as small as
possible. All crimp dimensions must be verified with a calibrated measuring device.
Printed: 24-Feb-23
CRIMP SPECIFICATIONS
Crimper Hose Coupling Crimp Instructions CHART NUMBER 146 REV 01
Finn-Power 129G 5000 Skive Tolerance + 0.1/-0.2mm or + 0.004/-0.008 inches .
32 Series
Cover
Skive Crimp Dial Setting
Hose Ferrule Length Die Length Crimp Diameter Approx. Actual
mm mm in
NOTE: Die and dial settings are approximate recommendations. Ferrules should be crimped with
IT49 01 the largest diameter die set available to make the ridges on the finished crimp as small as
possible. All crimp dimensions must be verified with a calibrated measuring device.
Printed: 24-Feb-23
CRIMP SPECIFICATIONS
Crimper Hose Coupling Crimp Instructions CHART NUMBER 164 REV 00
Finn-Power 120J 4200 One-piece Mark the hose at a distance from the end of the hose equal to the "Insertion Length". Install the
fitting on the hose so that the mark is even with the end of the ferrule. Crimp the entire length of
32 Series the ferrule to the Crimp Diameter given in the table. Tolerance +0.1mm/- 0.2mm or + 0.004/-0.008
inches.
Fitting
Insertion Crimp Dial Setting
Hose Ferrule Length Die Length Crimp Diameter Approx. Actual
mm mm in
NOTE: Die and dial settings are approximate recommendations. Ferrules should be crimped with
IT63 00 the largest diameter die set available to make the ridges on the finished crimp as small as
possible. All crimp dimensions must be verified with a calibrated measuring device.
Printed: 24-Feb-23
CRIMP SPECIFICATIONS
Crimper Hose Coupling Crimp Instructions CHART NUMBER 195 REV H
Finn-Power 158 4000 Non Skive Tolerance +/- 0.1mm or +/- 0.004 inches .
32 Series
NOTE: Die and dial settings are approximate recommendations. Ferrules should be crimped with
TFS-100 H the largest diameter die set available to make the ridges on the finished crimp as small as
possible. All crimp dimensions must be verified with a calibrated measuring device.
Printed: 24-Feb-23
CRIMP SPECIFICATIONS
Crimper Hose Coupling Crimp Instructions CHART NUMBER 190 REV 01
Finn-Power 158 4700 One-piece Mark the hose at a distance from the end of the hose equal to the "Insertion Length". Install the
fitting on the hose so that the mark is even with the end of the ferrule. Crimp the entire length of
32 Series the ferrule to the Crimp Diameter given in the table. Tolerance +0.0mm/- 0.2mm or + 0.004/-0.008
inches.
Fitting
Insertion Crimp Dial Setting
Hose Ferrule Die Length Crimp Diameter Approx. Actual
mm in
NOTE: Die and dial settings are approximate recommendations. Ferrules should be crimped with
IT74 01 the largest diameter die set available to make the ridges on the finished crimp as small as
possible. All crimp dimensions must be verified with a calibrated measuring device.
Printed: 24-Feb-23
CRIMP SPECIFICATIONS
Crimper Hose Coupling Crimp Instructions CHART NUMBER 191 REV 01
Finn-Power 158 5000 One-piece Tolerance + 0.1/-0.2mm or + 0.004/-0.008 inches .
32 Series
Fitting
Insertion Crimp Dial Setting
Hose Ferrule Die Length Crimp Diameter Approx. Actual
mm in
NOTE: Die and dial settings are approximate recommendations. Ferrules should be crimped with
IT75 01 the largest diameter die set available to make the ridges on the finished crimp as small as
possible. All crimp dimensions must be verified with a calibrated measuring device.
Printed: 24-Feb-23
CRIMP SPECIFICATIONS
Crimper Hose Coupling Crimp Instructions CHART NUMBER 157 REV 00
Finn-Power 172 4700 Non-Skive Mark the hose at a distance from the end of the hose equal to the "Insertion Length". Install the
fitting on the hose so that the mark is even with the end of the ferrule. Crimp the entire length of
32 Series the ferrule to the Crimp Diameter given in the table. Tolerance +0.0mm/- 0.2mm or + 0.004/-0.008
inches.
Fitting
Insertion Crimp Dial Setting
Hose Ferrule Die Length Crimp Diameter Approx. Actual
mm in
NOTE: Die and dial settings are approximate recommendations. Ferrules should be crimped with
IT57 00 the largest diameter die set available to make the ridges on the finished crimp as small as
possible. All crimp dimensions must be verified with a calibrated measuring device.
Printed: 24-Feb-23
CRIMP SPECIFICATIONS
Crimper Hose Coupling Crimp Instructions CHART NUMBER 175 REV 00
Finn-Power 182 4700 Non-Skive Mark the hose at a distance from the end of the hose equal to the "Insertion Length". Install the
fitting on the hose so that the mark is even with the end of the ferrule. Crimp the entire length of
32 Series the ferrule to the Crimp Diameter given in the table. Tolerance +0.0mm/- 0.2mm or + 0.004/-0.008
inches.
Fitting
Insertion Crimp Dial Setting
Hose Ferrule Die Length Crimp Diameter Approx. Actual
mm in
NOTE: Die and dial settings are approximate recommendations. Ferrules should be crimped with
IT66 00 the largest diameter die set available to make the ridges on the finished crimp as small as
possible. All crimp dimensions must be verified with a calibrated measuring device.
Printed: 24-Feb-23
CRIMP SPECIFICATIONS
Crimper Hose Coupling Crimp Instructions CHART NUMBER 189 REV 00
Finn-Power 173 4700 One-piece Mark the hose at a distance from the end of the hose equal to the "Insertion Length". Install the
fitting on the hose so that the mark is even with the end of the ferrule. Crimp the entire length of
32 Series the ferrule to the Crimp Diameter given in the table. Tolerance +0.0mm/- 0.2mm or + 0.004/-0.008
inches.
Fitting
Insertion Crimp Dial Setting
Hose Ferrule Die Length Crimp Diameter Approx. Actual
mm in
NOTE: Die and dial settings are approximate recommendations. Ferrules should be crimped with
PUL 173 00 the largest diameter die set available to make the ridges on the finished crimp as small as
possible. All crimp dimensions must be verified with a calibrated measuring device.
Printed: 24-Feb-23
CRIMP SPECIFICATIONS
Crimper Hose Coupling Crimp Instructions CHART NUMBER 96 REV 00
Finn-Power 109 5000 Two-piece Tolerance + 0.1/-0.2mm or + 0.004/-0.008 inches .
32 Series
Cover Fitting
Skive Insertion Crimp Dial Setting
Hose Ferrule Length Length Die Length Crimp Diameter Approx. Actual
mm mm mm in
NOTE: Die and dial settings are approximate recommendations. Ferrules should be crimped with
IT13 00 the largest diameter die set available to make the ridges on the finished crimp as small as
possible. All crimp dimensions must be verified with a calibrated measuring device.
Printed: 24-Feb-23
CRIMP SPECIFICATIONS
Crimper Hose Coupling Crimp Instructions CHART NUMBER 184 REV 00
Finn-Power 110 5000 Two-piece Tolerance + 0.1/-0.2mm or + 0.004/-0.008 inches .
32 Series
Fitting
Insertion Crimp Dial Setting
Hose Ferrule Length Die Length Crimp Diameter Approx. Actual
mm mm in
NOTE: Die and dial settings are approximate recommendations. Ferrules should be crimped with
IT70 00 the largest diameter die set available to make the ridges on the finished crimp as small as
possible. All crimp dimensions must be verified with a calibrated measuring device.
Printed: 24-Feb-23
CRIMP SPECIFICATIONS
Crimper Hose Coupling Crimp Instructions CHART NUMBER 116 REV 00
Finn-Power 112 5000 Skive Tolerance + 0.1/-0.2mm or + 0.004/-0.008 inches .
32 Series
Cover
Skive Crimp Dial Setting
Hose Ferrule Length Die Length Crimp Diameter Approx. Actual
mm mm in
NOTE: Die and dial settings are approximate recommendations. Ferrules should be crimped with
IT30 00 the largest diameter die set available to make the ridges on the finished crimp as small as
possible. All crimp dimensions must be verified with a calibrated measuring device.
Printed: 24-Feb-23
CRIMP SPECIFICATIONS
Crimper Hose Coupling Crimp Instructions CHART NUMBER 113 REV 00
Finn-Power 111 5000 Skive Tolerance + 0.1/-0.2mm or + 0.004/-0.008 inches .
32 Series
Cover
Skive Crimp Dial Setting
Hose Ferrule Length Die Length Crimp Diameter Approx. Actual
mm mm in
NOTE: Die and dial settings are approximate recommendations. Ferrules should be crimped with
IT27 00 the largest diameter die set available to make the ridges on the finished crimp as small as
possible. All crimp dimensions must be verified with a calibrated measuring device.
Printed: 24-Feb-23
CRIMP SPECIFICATIONS
Crimper Hose Coupling Crimp Instructions CHART NUMBER 111 REV 00
Finn-Power 122 5000 Skive Tolerance + 0.1/-0.2mm or + 0.004/-0.008 inches .
32 Series
Cover
Skive Crimp Dial Setting
Hose Ferrule Length Die Length Crimp Diameter Approx. Actual
mm mm in
NOTE: Die and dial settings are approximate recommendations. Ferrules should be crimped with
IT26 00 the largest diameter die set available to make the ridges on the finished crimp as small as
possible. All crimp dimensions must be verified with a calibrated measuring device.
Printed: 24-Feb-23
CRIMP SPECIFICATIONS
Crimper Hose Coupling Crimp Instructions CHART NUMBER 150 REV 01
Finn-Power 124 5000 Two-piece Tolerance + 0.1/-0.2mm or + 0.004/-0.008 inches .
32 Series
PLUS
Cover
Skive Crimp Dial Setting
Hose Ferrule Length Die Length Crimp Diameter Approx. Actual
mm mm in
124 PLUS -06 5420 25 32-22 Full 23.0 0.906 1.0
124 PLUS -08 5420 27 32-26 Full 26.2 1.031 0.2
124 PLUS -10 5420 30 32-26 Full 29.0 1.142 3.0
124 PLUS -12 5420 32 32-30 Full 33.4 1.315 3.4
124 PLUS -16 5420 43 32-39 Full 41.7 1.642 2.7
124 PLUS -20 5420 44 32-45 Full 47.5 1.870 2.5
124 PLUS -24 5420 57 32-51 Full 56.0 2.205 5.0
124 PLUS -32 5420 72 32-69 Full 71.6 2.819 2.6
NOTE: Die and dial settings are approximate recommendations. Ferrules should be crimped with
IT52 01 the largest diameter die set available to make the ridges on the finished crimp as small as
possible. All crimp dimensions must be verified with a calibrated measuring device.
Printed: 24-Feb-23
CRIMP SPECIFICATIONS
Crimper Hose Coupling Crimp Instructions CHART NUMBER 156 REV 00
Finn-Power 124 5000 Two-piece Tolerance + 0.1/-0.2mm or + 0.004/-0.008 inches .
32 Series
PLUS
NOTE: Die and dial settings are approximate recommendations. Ferrules should be crimped with
IT56 00 the largest diameter die set available to make the ridges on the finished crimp as small as
possible. All crimp dimensions must be verified with a calibrated measuring device.
Printed: 24-Feb-23
CRIMP SPECIFICATIONS
Crimper Hose Coupling Crimp Instructions CHART NUMBER 172 REV 00
Finn-Power 156 5000 Two-piece Tolerance + 0.1/-0.2mm or + 0.004/-0.008 inches .
32 Series
PLUS
Cover
Skive Crimp Dial Setting
Hose Ferrule Length Die Length Crimp Diameter Approx. Actual
mm mm in
156 PLUS -12 5420 32 32-30 Full 33.9 1.335 3.9
156 PLUS -16 5420 43 32-39 Full 40.8 1.606 1.8
NOTE: Die and dial settings are approximate recommendations. Ferrules should be crimped with
IT64 00 the largest diameter die set available to make the ridges on the finished crimp as small as
possible. All crimp dimensions must be verified with a calibrated measuring device.
Printed: 24-Feb-23
CRIMP SPECIFICATIONS
Crimper Hose Coupling Crimp Instructions CHART NUMBER 173 REV 01
Finn-Power 156 5000 Two-piece Tolerance + 0.1/-0.2mm or + 0.004/-0.008 inches .
32 Series
PLUS
NOTE: Die and dial settings are approximate recommendations. Ferrules should be crimped with
IT65 01 the largest diameter die set available to make the ridges on the finished crimp as small as
possible. All crimp dimensions must be verified with a calibrated measuring device.
Printed: 24-Feb-23
CRIMP SPECIFICATIONS
Crimper Hose Coupling Crimp Instructions CHART NUMBER 112 REV 00
Finn-Power G102 5000 Non Skive Tolerance + 0.1/-0.2mm or + 0.004/-0.008 inches .
32 Series
Fitting
Insertion Crimp Dial Setting
Hose Ferrule Length Die Length Crimp Diameter Approx. Actual
mm mm in
NOTE: Die and dial settings are approximate recommendations. Ferrules should be crimped with
PUL 102 00 the largest diameter die set available to make the ridges on the finished crimp as small as
possible. All crimp dimensions must be verified with a calibrated measuring device.
Printed: 24-Feb-23
CRIMP SPECIFICATIONS
Crimper Hose Coupling Crimp Instructions CHART NUMBER 196 REV 00
Finn-Power G103 5000 Non Skive Tolerance + 0.1/-0.2mm or + 0.004/-0.008 inches .
32 Series
Fitting
Insertion Crimp Dial Setting
Hose Ferrule Length Die Length Crimp Diameter Approx. Actual
mm mm in
NOTE: Die and dial settings are approximate recommendations. Ferrules should be crimped with
PUL G103 00 the largest diameter die set available to make the ridges on the finished crimp as small as
possible. All crimp dimensions must be verified with a calibrated measuring device.
Printed: 24-Feb-23
CRIMP SPECIFICATIONS
Crimper Hose Coupling Crimp Instructions CHART NUMBER 153 REV 00
Finn-Power 114 5000 Two-piece Tolerance + 0.1/-0.2mm or + 0.004/-0.008 inches .
32 Series
Cover
Skive Crimp Dial Setting
Hose Ferrule Length Die Length Crimp Diameter Approx. Actual
mm mm in
NOTE: Die and dial settings are approximate recommendations. Ferrules should be crimped with
IT55 00 the largest diameter die set available to make the ridges on the finished crimp as small as
possible. All crimp dimensions must be verified with a calibrated measuring device.
Printed: 24-Feb-23
CRIMP SPECIFICATIONS
Crimper Hose Coupling Crimp Instructions CHART NUMBER 100 REV 00
Finn-Power 111 5000 Non-Skive Tolerance + 0.1/-0.2mm or + 0.004/-0.008 inches .
32 Series
Fitting
Insertion Crimp Dial Setting
Hose Ferrule Length Die Length Crimp Diameter Approx. Actual
mm mm in
NOTE: Die and dial settings are approximate recommendations. Ferrules should be crimped with
IT15 00 the largest diameter die set available to make the ridges on the finished crimp as small as
possible. All crimp dimensions must be verified with a calibrated measuring device.
Printed: 24-Feb-23
CRIMP SPECIFICATIONS
Crimper Hose Coupling Crimp Instructions CHART NUMBER 130 REV 00
Finn-Power 114 5000 Two-piece Tolerance + 0.1/-0.2mm or + 0.004/-0.008 inches .
32 Series
Fitting
Insertion Crimp Dial Setting
Hose Ferrule Length Die Length Crimp Diameter Approx. Actual
mm mm in
NOTE: Die and dial settings are approximate recommendations. Ferrules should be crimped with
IT40 00 the largest diameter die set available to make the ridges on the finished crimp as small as
possible. All crimp dimensions must be verified with a calibrated measuring device.
Printed: 24-Feb-23
CRIMP SPECIFICATIONS
Crimper Hose Coupling Crimp Instructions CHART NUMBER 102 REV 00
Finn-Power 112 5000 Non-Skive Tolerance + 0.1/-0.2mm or + 0.004/-0.008 inches .
32 Series
Fitting
Insertion Crimp Dial Setting
Hose Ferrule Length Die Length Crimp Diameter Approx. Actual
mm mm in
NOTE: Die and dial settings are approximate recommendations. Ferrules should be crimped with
IT17 00 the largest diameter die set available to make the ridges on the finished crimp as small as
possible. All crimp dimensions must be verified with a calibrated measuring device.
Printed: 24-Feb-23
CRIMP SPECIFICATIONS
Crimper Hose Coupling Crimp Instructions CHART NUMBER 101 REV 00
Finn-Power 122 5000 Non-Skive Tolerance + 0.1/-0.2mm or + 0.004/-0.008 inches .
32 Series
Fitting
Insertion Crimp Dial Setting
Hose Ferrule Length Die Length Crimp Diameter Approx. Actual
mm mm in
NOTE: Die and dial settings are approximate recommendations. Ferrules should be crimped with
IT16 00 the largest diameter die set available to make the ridges on the finished crimp as small as
possible. All crimp dimensions must be verified with a calibrated measuring device.
Printed: 24-Feb-23
CRIMP SPECIFICATIONS
Crimper Hose Coupling Crimp Instructions CHART NUMBER 105 REV 00
Finn-Power 122 5000 Skive Tolerance + 0.1/-0.2mm or + 0.004/-0.008 inches .
32 Series
Cover
Skive Crimp Dial Setting
Hose Ferrule Length Die Length Crimp Diameter Approx. Actual
mm mm in
NOTE: Die and dial settings are approximate recommendations. Ferrules should be crimped with
IT20 00 the largest diameter die set available to make the ridges on the finished crimp as small as
possible. All crimp dimensions must be verified with a calibrated measuring device.
Printed: 24-Feb-23
CRIMP SPECIFICATIONS
Crimper Hose Coupling Crimp Instructions CHART NUMBER 103 REV 02
Finn-Power 124 5000 Two-piece Tolerance + 0.1/-0.2mm or + 0.004/-0.008 inches .
32 Series
NOTE: Die and dial settings are approximate recommendations. Ferrules should be crimped with
IT18 02 the largest diameter die set available to make the ridges on the finished crimp as small as
possible. All crimp dimensions must be verified with a calibrated measuring device.
Printed: 24-Feb-23
CRIMP SPECIFICATIONS
Crimper Hose Coupling Crimp Instructions CHART NUMBER 106 REV 00
Finn-Power 124 5000 Skive Tolerance + 0.1/-0.2mm or + 0.004/-0.008 inches .
32 Series
Cover
Skive Crimp Dial Setting
Hose Ferrule Length Die Length Crimp Diameter Approx. Actual
mm mm in
NOTE: Die and dial settings are approximate recommendations. Ferrules should be crimped with
IT21 00 the largest diameter die set available to make the ridges on the finished crimp as small as
possible. All crimp dimensions must be verified with a calibrated measuring device.
Printed: 24-Feb-23
CRIMP SPECIFICATIONS
Crimper Hose Coupling Crimp Instructions CHART NUMBER 108 REV 00
Finn-Power 136 5000 Skive Tolerance + 0.1/-0.2mm or + 0.004/-0.008 inches .
32 Series
Cover
Skive Crimp Dial Setting
Hose Ferrule Length Die Length Crimp Diameter Approx. Actual
mm mm in
NOTE: Die and dial settings are approximate recommendations. Ferrules should be crimped with
IT23 00 the largest diameter die set available to make the ridges on the finished crimp as small as
possible. All crimp dimensions must be verified with a calibrated measuring device.
Printed: 24-Feb-23
CRIMP SPECIFICATIONS
Crimper Hose Coupling Crimp Instructions CHART NUMBER 110 REV 01
Finn-Power 141 5000 Non-Skive Tolerance + 0.1/-0.2mm or + 0.004/-0.008 inches .
32 Series
Fitting
Insertion Crimp Dial Setting
Hose Ferrule Length Die Length Crimp Diameter Approx. Actual
mm mm in
NOTE: Die and dial settings are approximate recommendations. Ferrules should be crimped with
IT25 01 the largest diameter die set available to make the ridges on the finished crimp as small as
possible. All crimp dimensions must be verified with a calibrated measuring device.
Printed: 24-Feb-23
CRIMP SPECIFICATIONS
Crimper Hose Coupling Crimp Instructions CHART NUMBER 109 REV 00
Finn-Power 156 5000 Skive Tolerance + 0.1/-0.2mm or + 0.004/-0.008 inches .
32 Series
Cover
Skive Crimp Dial Setting
Hose Ferrule Length Die Length Crimp Diameter Approx. Actual
mm mm in
NOTE: Die and dial settings are approximate recommendations. Ferrules should be crimped with
IT24 00 the largest diameter die set available to make the ridges on the finished crimp as small as
possible. All crimp dimensions must be verified with a calibrated measuring device.
Printed: 24-Feb-23
CRIMP SPECIFICATIONS
Crimper Hose Coupling Crimp Instructions CHART NUMBER 187 REV 00
Finn-Power T101 T1000F Two-piece
32 Series
Fitting
Insertion Crimp Dial Setting
Hose Ferrule Length Die Length Crimp Diameter Approx. Actual
mm mm in
NOTE: Die and dial settings are approximate recommendations. Ferrules should be crimped with
IT73 00 the largest diameter die set available to make the ridges on the finished crimp as small as
possible. All crimp dimensions must be verified with a calibrated measuring device.
Printed: 24-Feb-23
CRIMP SPECIFICATIONS
Crimper Hose Coupling Crimp Instructions CHART NUMBER 132 REV 00
Finn-Power 172 5000 Non-Skive Tolerance + 0.1/-0.2mm or + 0.004/-0.008 inches .
32 Series
Fitting
Insertion Crimp Dial Setting
Hose Ferrule Length Die Length Crimp Diameter Approx. Actual
mm mm in
NOTE: Die and dial settings are approximate recommendations. Ferrules should be crimped with
TO1 00 the largest diameter die set available to make the ridges on the finished crimp as small as
possible. All crimp dimensions must be verified with a calibrated measuring device.
Printed: 24-Feb-23
CRIMP SPECIFICATIONS
Crimper Hose Coupling Crimp Instructions CHART NUMBER 194 REV 01
Finn-Power 119MS 42/44/50 Non Skive
32 Series
NOTE: Die and dial settings are approximate recommendations. Ferrules should be crimped with
IT78 01 the largest diameter die set available to make the ridges on the finished crimp as small as
possible. All crimp dimensions must be verified with a calibrated measuring device.
Printed: 24-Feb-23
CRIMP SPECIFICATIONS
Crimper Hose Coupling Crimp Instructions CHART NUMBER 165 REV 00
Finn-Power 186SC 9800 One-piece Mark the hose at a distance from the end of the hose equal to the "Insertion Length". Install the
fitting on the hose so that the mark is even with the end of the ferrule. Crimp the entire length of
32 Series the ferrule to the Crimp Diameter given in the table. Tolerance +0.1mm/- 0.2mm or + 0.004/-0.008
inches.
Insertion
Depth Crimp Dial Setting
Hose Ferrule Die Length Crimp Diameter Approx. Actual
mm in
NOTE: Die and dial settings are approximate recommendations. Ferrules should be crimped with
PIR1 00 the largest diameter die set available to make the ridges on the finished crimp as small as
possible. All crimp dimensions must be verified with a calibrated measuring device.
Printed: 24-Feb-23
CRIMP SPECIFICATIONS
Crimper Hose Coupling Crimp Instructions CHART NUMBER 166 REV 00
Finn-Power 185SC 9800 One-piece Mark the hose at a distance from the end of the hose equal to the "Insertion Length". Install the
fitting on the hose so that the mark is even with the end of the ferrule. Crimp the entire length of
32 Series the ferrule to the Crimp Diameter given in the table. Tolerance +0.1mm/- 0.2mm or + 0.004/-0.008
inches.
Insertion
Depth Crimp Dial Setting
Hose Ferrule Die Length Crimp Diameter Approx. Actual
mm in
NOTE: Die and dial settings are approximate recommendations. Ferrules should be crimped with
PIR2 00 the largest diameter die set available to make the ridges on the finished crimp as small as
possible. All crimp dimensions must be verified with a calibrated measuring device.
Printed: 24-Feb-23
CRIMP SPECIFICATIONS
Crimper Hose Coupling Crimp Instructions CHART NUMBER 167 REV 00
Finn-Power 184SC 9800 One-piece Mark the hose at a distance from the end of the hose equal to the "Insertion Length". Install the
fitting on the hose so that the mark is even with the end of the ferrule. Crimp the entire length of
32 Series the ferrule to the Crimp Diameter given in the table. Tolerance +0.1mm/- 0.2mm or + 0.004/-0.008
inches.
Insertion
Depth Crimp Dial Setting
Hose Ferrule Die Length Crimp Diameter Approx. Actual
mm in
NOTE: Die and dial settings are approximate recommendations. Ferrules should be crimped with
PIR3 00 the largest diameter die set available to make the ridges on the finished crimp as small as
possible. All crimp dimensions must be verified with a calibrated measuring device.
Printed: 24-Feb-23
CRIMP SPECIFICATIONS
Crimper Hose Coupling Crimp Instructions CHART NUMBER 170 REV 00
Finn-Power 186SC 4700 One-piece Mark the hose at a distance from the end of the hose equal to the "Insertion Length". Install the
fitting on the hose so that the mark is even with the end of the ferrule. Crimp the entire length of
32 Series the ferrule to the Crimp Diameter given in the table. Tolerance +0.0mm/- 0.2mm or + 0.004/-0.008
inches.
Insertion
Depth Crimp Dial Setting
Hose Ferrule Die Length Crimp Diameter Approx. Actual
mm in
NOTE: Die and dial settings are approximate recommendations. Ferrules should be crimped with
PIR4 00 the largest diameter die set available to make the ridges on the finished crimp as small as
possible. All crimp dimensions must be verified with a calibrated measuring device.
Printed: 24-Feb-23
CRIMP SPECIFICATIONS
Crimper Hose Coupling Crimp Instructions CHART NUMBER 134 REV 0
Finn-Power 173 5000 Non-Skive Tolerance + 0.1/-0.2mm or + 0.004/-0.008 inches .
32 Series
NOTE: Die and dial settings are approximate recommendations. Ferrules should be crimped with
TO3 0 the largest diameter die set available to make the ridges on the finished crimp as small as
possible. All crimp dimensions must be verified with a calibrated measuring device.
Printed: 24-Feb-23
CRIMP SPECIFICATIONS
Crimper Hose Coupling Crimp Instructions CHART NUMBER 133 REV 0
Finn-Power 182 5000 Non-Skive Tolerance + 0.1/-0.2mm or + 0.004/-0.008 inches .
32 Series
NOTE: Die and dial settings are approximate recommendations. Ferrules should be crimped with
TO2 0 the largest diameter die set available to make the ridges on the finished crimp as small as
possible. All crimp dimensions must be verified with a calibrated measuring device.
Printed: 24-Feb-23
CRIMP SPECIFICATIONS
Crimper Hose Coupling Crimp Instructions CHART NUMBER 181 REV 0
Finn-Power 111 4500 One-piece Mark the hose at a distance from the end of the hose equal to the "Insertion Length". Install the
fitting on the hose so that the mark is even with the end of the ferrule. Crimp the entire length of
32 Series the ferrule to the Crimp Diameter given in the table. Tolerance +0.1mm/- 0.2mm or + 0.004/-0.008
inches.
Crimp Fitting
Insert Insertion Crimp Dial Setting
Hose Ferrule Size Die Length Crimp Diameter Approx. Actual
mm in
NOTE: Die and dial settings are approximate recommendations. Ferrules should be crimped with
PUL 111 0 the largest diameter die set available to make the ridges on the finished crimp as small as
possible. All crimp dimensions must be verified with a calibrated measuring device.
Printed: 24-Feb-23
CRIMP SPECIFICATIONS
Crimper Hose Coupling Crimp Instructions CHART NUMBER 52 REV 0
Finn-Power 111 9000SB Skive Tolerance +/- 0.1mm or +/- 0.004 inches .
32 Series
Cover Fitting
Skive Insertion Crimp Dial Setting
Hose Ferrule Length Length Die Length Crimp Diameter Approx. Actual
mm mm mm in
NOTE: Die and dial settings are approximate recommendations. Ferrules should be crimped with
PUL Grease 0 the largest diameter die set available to make the ridges on the finished crimp as small as
possible. All crimp dimensions must be verified with a calibrated measuring device.
Printed: 24-Feb-23
CRIMP SPECIFICATIONS
Crimper Hose Coupling Crimp Instructions CHART NUMBER 88 REV 00
Finn-Power 111 4400 One-piece Mark the hose at a distance from the end of the hose equal to the "Insertion Length". Install the
fitting on the hose so that the mark is even with the end of the ferrule. Crimp the entire length of
32 Series the ferrule to the Crimp Diameter given in the table. Tolerance +0.1mm/- 0.2mm or + 0.004/-0.008
inches.
Fitting
Insertion Crimp Dial Setting
Hose Ferrule Length Die Length Crimp Diameter Approx. Actual
mm mm in
NOTE: Die and dial settings are approximate recommendations. Ferrules should be crimped with
IT06 00 the largest diameter die set available to make the ridges on the finished crimp as small as
possible. All crimp dimensions must be verified with a calibrated measuring device.
Printed: 24-Feb-23
CRIMP SPECIFICATIONS
Crimper Hose Coupling Crimp Instructions CHART NUMBER 90 REV 01
Finn-Power 112 4400 One-piece Mark the hose at a distance from the end of the hose equal to the "Insertion Length". Install the
fitting on the hose so that the mark is even with the end of the ferrule. Crimp the entire length of
32 Series the ferrule to the Crimp Diameter given in the table. Tolerance +0.1mm/- 0.2mm or + 0.004/-0.008
inches.
Fitting
Insertion Crimp Dial Setting
Hose Ferrule Length Die Length Crimp Diameter Approx. Actual
mm mm in
NOTE: Die and dial settings are approximate recommendations. Ferrules should be crimped with
IT08 01 the largest diameter die set available to make the ridges on the finished crimp as small as
possible. All crimp dimensions must be verified with a calibrated measuring device.
Printed: 24-Feb-23
CRIMP SPECIFICATIONS
Crimper Hose Coupling Crimp Instructions CHART NUMBER 131 REV 00
Finn-Power 114 4400 One-piece Mark the hose at a distance from the end of the hose equal to the "Insertion Length". Install the
fitting on the hose so that the mark is even with the end of the ferrule. Crimp the entire length of
32 Series the ferrule to the Crimp Diameter given in the table. Tolerance +0.1mm/- 0.2mm or + 0.004/-0.008
inches.
Fitting
Insertion Crimp Dial Setting
Hose Ferrule Length Die Length Crimp Diameter Approx. Actual
mm mm in
NOTE: Die and dial settings are approximate recommendations. Ferrules should be crimped with
IT41 00 the largest diameter die set available to make the ridges on the finished crimp as small as
possible. All crimp dimensions must be verified with a calibrated measuring device.
Printed: 24-Feb-23
CRIMP SPECIFICATIONS
Crimper Hose Coupling Crimp Instructions CHART NUMBER 89 REV 00
Finn-Power 122 4400 One-piece Mark the hose at a distance from the end of the hose equal to the "Insertion Length". Install the
fitting on the hose so that the mark is even with the end of the ferrule. Crimp the entire length of
32 Series the ferrule to the Crimp Diameter given in the table. Tolerance +0.1mm/- 0.2mm or + 0.004/-0.008
inches.
Fitting
Insertion Crimp Dial Setting
Hose Ferrule Length Die Length Crimp Diameter Approx. Actual
mm mm in
NOTE: Die and dial settings are approximate recommendations. Ferrules should be crimped with
IT07 00 the largest diameter die set available to make the ridges on the finished crimp as small as
possible. All crimp dimensions must be verified with a calibrated measuring device.
Printed: 24-Feb-23
CRIMP SPECIFICATIONS
Crimper Hose Coupling Crimp Instructions CHART NUMBER 114 REV 00
Finn-Power 119 5000 Skive Tolerance + 0.1/-0.2mm or + 0.004/-0.008 inches .
32 Series
Cover
Skive Crimp Dial Setting
Hose Ferrule Length Die Length Crimp Diameter Approx. Actual
mm mm in
NOTE: Die and dial settings are approximate recommendations. Ferrules should be crimped with
IT28 00 the largest diameter die set available to make the ridges on the finished crimp as small as
possible. All crimp dimensions must be verified with a calibrated measuring device.
Printed: 24-Feb-23
CRIMP SPECIFICATIONS
Crimper Hose Coupling Crimp Instructions CHART NUMBER 148 REV 00
Finn-Power 124 9600 One-piece Cover must be removed before the fittings can be attached. Leave a section of ferrule nearest
thread end of fitting uncrimped,crimp only to the position described in "Crimp Length". Crimp
32 Series
PLUS diameter tolerance +/- 0.1mm.
Cover
Skive Crimp Dial Setting
Hose Ferrule Length Die Length Crimp Diameter Approx. Actual
mm mm in
124 PLUS -12 9600 46 32-30 Knurl 32.2 1.268 2.2
124 PLUS -16 9600 50 32-39 Knurl 40.1 1.579 1.1
124 PLUS -20 9600 54 32-45 Knurl 48.0 1.890 3.0
124 PLUS -24 9600 56 32-51 Knurl 56.0 2.205 5.0
124 PLUS -32 9600 82 32-69 Knurl 71.2 2.803 2.2
NOTE: Die and dial settings are approximate recommendations. Ferrules should be crimped with
IT50 00 the largest diameter die set available to make the ridges on the finished crimp as small as
possible. All crimp dimensions must be verified with a calibrated measuring device.
Printed: 24-Feb-23
CRIMP SPECIFICATIONS
Crimper Hose Coupling Crimp Instructions CHART NUMBER 135 REV 00
Finn-Power 124 9600 One-piece Cover must be removed before the fittings can be attached. Leave a section of ferrule nearest
thread end of fitting uncrimped,crimp only to the position described in "Crimp Length". Crimp
32 Series diameter tolerance +/- 0.1mm.
Cover
Skive Crimp Dial Setting
Hose Ferrule Length Die Length Crimp Diameter Approx. Actual
mm mm in
NOTE: Die and dial settings are approximate recommendations. Ferrules should be crimped with
IT42 00 the largest diameter die set available to make the ridges on the finished crimp as small as
possible. All crimp dimensions must be verified with a calibrated measuring device.
Printed: 24-Feb-23
CRIMP SPECIFICATIONS
Crimper Hose Coupling Crimp Instructions CHART NUMBER 149 REV 00
Finn-Power 124 8000 Interlock Tolerance +0.1mm/- 0.2mm or + 0.004/-0.008 inches .
32 Series
PLUS
Cover Tube
Skive Skive Crimp Dial Setting
Hose Ferrule Length Length Die Length Crimp Diameter Approx. Actual
mm mm mm in
124 PLUS -12 8640 52 15 32-30 Full 33.8 1.331 3.8
124 PLUS -16 8640 65 17 32-39 Full 40.9 1.610 1.9
124 PLUS -20 8640 74 21.5 32-45 Full 50.2 1.976 5.2
124 PLUS -24 8640 81 22 32-57 Full 58.0 2.283 1.0
124 PLUS -32 8640 85 29 32-69 Full 73.3 2.886 4.3
NOTE: Die and dial settings are approximate recommendations. Ferrules should be crimped with
IT51 00 the largest diameter die set available to make the ridges on the finished crimp as small as
possible. All crimp dimensions must be verified with a calibrated measuring device.
Printed: 24-Feb-23
CRIMP SPECIFICATIONS
Crimper Hose Coupling Crimp Instructions CHART NUMBER 162 REV 00
Finn-Power 156 9600 One-piece Cover must be removed before the fittings can be attached. Leave a section of ferrule nearest
thread end of fitting uncrimped,crimp only to the position described in "Crimp Length". Crimp
32 Series
PLUS diameter tolerance +/- 0.1mm.
Cover
Skive Crimp Dial Setting
Hose Ferrule Length Die Length Crimp Diameter Approx. Actual
mm mm in
156 PLUS -12 9600 46 32-30 Knurl 32.2 1.268 2.2
156 PLUS -16 9600 50 32-39 Knurl 40.5 1.594 1.5
156 PLUS -20 9600 54 32-51 Knurl 52.0 2.047 1.0
156 PLUS -24 9600 56 32-57 Knurl 58.4 2.299 1.4
NOTE: Die and dial settings are approximate recommendations. Ferrules should be crimped with
IT61 00 the largest diameter die set available to make the ridges on the finished crimp as small as
possible. All crimp dimensions must be verified with a calibrated measuring device.
Printed: 24-Feb-23
CRIMP SPECIFICATIONS
Crimper Hose Coupling Crimp Instructions CHART NUMBER 137 REV 00
Finn-Power 156 9600 One-piece Cover must be removed before the fittings can be attached. Leave a section of ferrule nearest
thread end of fitting uncrimped,crimp only to the position described in "Crimp Length". Crimp
32 Series diameter tolerance +/- 0.1mm.
Cover
Skive Crimp Dial Setting
Hose Ferrule Length Die Length Crimp Diameter Approx. Actual
mm mm in
NOTE: Die and dial settings are approximate recommendations. Ferrules should be crimped with
IT44 00 the largest diameter die set available to make the ridges on the finished crimp as small as
possible. All crimp dimensions must be verified with a calibrated measuring device.
Printed: 24-Feb-23
CRIMP SPECIFICATIONS
Crimper Hose Coupling Crimp Instructions CHART NUMBER 129 REV 00
Finn-Power 156 8600 Interlock Tolerance +0.1mm/- 0.2mm or + 0.004/-0.008 inches .
32 Series
Cover Tube
Skive Skive Crimp Dial Setting
Hose Ferrule Length Length Die Length Crimp Diameter Approx. Actual
mm mm mm in
NOTE: Die and dial settings are approximate recommendations. Ferrules should be crimped with
IT39 00 the largest diameter die set available to make the ridges on the finished crimp as small as
possible. All crimp dimensions must be verified with a calibrated measuring device.
Printed: 24-Feb-23
CRIMP SPECIFICATIONS
Crimper Hose Coupling Crimp Instructions CHART NUMBER 136 REV 00
Finn-Power 136 9600 One-piece Cover must be removed before the fittings can be attached. Leave a section of ferrule nearest
thread end of fitting uncrimped,crimp only to the position described in "Crimp Length". Crimp
32 Series diameter tolerance +/- 0.1mm.
Cover
Skive Crimp Dial Setting
Hose Ferrule Length Die Length Crimp Diameter Approx. Actual
mm mm in
NOTE: Die and dial settings are approximate recommendations. Ferrules should be crimped with
IT43 00 the largest diameter die set available to make the ridges on the finished crimp as small as
possible. All crimp dimensions must be verified with a calibrated measuring device.
Printed: 24-Feb-23
CRIMP SPECIFICATIONS
Crimper Hose Coupling Crimp Instructions CHART NUMBER 128 REV 00
Finn-Power 136 8600 Interlock Tolerance +0.1mm/- 0.2mm or + 0.004/-0.008 inches .
32 Series
Cover Tube
Skive Skive Crimp Dial Setting
Hose Ferrule Length Length Die Length Crimp Diameter Approx. Actual
mm mm mm in
NOTE: Die and dial settings are approximate recommendations. Ferrules should be crimped with
IT38 00 the largest diameter die set available to make the ridges on the finished crimp as small as
possible. All crimp dimensions must be verified with a calibrated measuring device.
Printed: 24-Feb-23
CRIMP SPECIFICATIONS
Crimper Hose Coupling Crimp Instructions CHART NUMBER 154 REV 00
Finn-Power 663 4400 One Piece Mark the hose at a distance from the end of the hose equal to the "Insertion Length". Install the
fitting on the hose so that the mark is even with the end of the ferrule. Crimp the entire length of
32 Series the ferrule to the Crimp Diameter given in the table. Tolerance +0.1mm/- 0.2mm or + 0.004/-0.008
inches.
Fitting
Insertion Crimp Dial Setting
Hose Ferrule Length Die Length Crimp Diameter Approx. Actual
mm mm in
NOTE: Die and dial settings are approximate recommendations. Ferrules should be crimped with
PUL633/4400 00 the largest diameter die set available to make the ridges on the finished crimp as small as
possible. All crimp dimensions must be verified with a calibrated measuring device.
Printed: 24-Feb-23
CRIMP SPECIFICATIONS
Crimper Hose Coupling Crimp Instructions CHART NUMBER 168 REV 00
Finn-Power 663 9600 One-piece Cover must be removed before the fittings can be attached. Leave a section of ferrule nearest
thread end of fitting uncrimped,crimp only to the position described in "Crimp Length". Crimp
32 Series diameter tolerance +/- 0.1mm.
Cover
Skive Crimp Dial Setting
Hose Ferrule Length Die Length Crimp Diameter Approx. Actual
mm mm in
NOTE: Die and dial settings are approximate recommendations. Ferrules should be crimped with
PUL663/9600 00 the largest diameter die set available to make the ridges on the finished crimp as small as
possible. All crimp dimensions must be verified with a calibrated measuring device.
Printed: 24-Feb-23
CRIMP SPECIFICATIONS
Crimper Hose Coupling Crimp Instructions CHART NUMBER 155 REV 00
Finn-Power 665 4400 One Piece Mark the hose at a distance from the end of the hose equal to the "Insertion Length". Install the
fitting on the hose so that the mark is even with the end of the ferrule. Crimp the entire length of
32 Series the ferrule to the Crimp Diameter given in the table. Tolerance +0.1mm/- 0.2mm or + 0.004/-0.008
inches.
Cover
Skive Crimp Dial Setting
Hose Ferrule Length Die Length Crimp Diameter Approx. Actual
mm mm in
NOTE: Die and dial settings are approximate recommendations. Ferrules should be crimped with
PUL665/4400 00 the largest diameter die set available to make the ridges on the finished crimp as small as
possible. All crimp dimensions must be verified with a calibrated measuring device.
Printed: 24-Feb-23
CRIMP SPECIFICATIONS
Crimper Hose Coupling Crimp Instructions CHART NUMBER 169 REV 00
Finn-Power 665 9600 One Piece Cover must be removed before the fittings can be attached. Leave a section of ferrule nearest
thread end of fitting uncrimped,crimp only to the position described in "Crimp Length". Crimp
32 Series diameter tolerance +/- 0.1mm.
Cover
Skive Crimp Dial Setting
Hose Ferrule Length Die Length Crimp Diameter Approx. Actual
mm mm in
NOTE: Die and dial settings are approximate recommendations. Ferrules should be crimped with
PUL665/9600 00 the largest diameter die set available to make the ridges on the finished crimp as small as
possible. All crimp dimensions must be verified with a calibrated measuring device.
Printed: 24-Feb-23
CRIMP SPECIFICATIONS
Crimper Hose Coupling Crimp Instructions CHART NUMBER 140 REV 1
Finn-Power 663 8000 Interlock Tolerance +0.1mm/- 0.2mm or + 0.004/-0.008 inches .
32 Series
Cover Tube
Skive Skive Crimp Dial Setting
Hose Ferrule Length Length Die Length Crimp Diameter Approx. Actual
mm mm mm in
NOTE: Die and dial settings are approximate recommendations. Ferrules should be crimped with
IT633 1 the largest diameter die set available to make the ridges on the finished crimp as small as
possible. All crimp dimensions must be verified with a calibrated measuring device.
Printed: 24-Feb-23
CRIMP SPECIFICATIONS
Crimper Hose Coupling Crimp Instructions CHART NUMBER 141 REV 1
Finn-Power 665 8000 Interlock Tolerance +0.1mm/- 0.2mm or + 0.004/-0.008 inches .
32 Series
Cover Tube
Skive Skive Crimp Dial Setting
Hose Ferrule Length Length Die Length Crimp Diameter Approx. Actual
mm mm mm in
NOTE: Die and dial settings are approximate recommendations. Ferrules should be crimped with
IT665 1 the largest diameter die set available to make the ridges on the finished crimp as small as
possible. All crimp dimensions must be verified with a calibrated measuring device.
Printed: 24-Feb-23
CRIMP SPECIFICATIONS
Crimper Hose Coupling Crimp Instructions CHART NUMBER 142 REV 00
Finn-Power 153 8400 Interlock Tolerance +/- 0.1mm or +/- 0.004 inches .
32 Series
Cover Tube
Skive Skive Crimp Dial Setting
Hose Ferrule length Length Die Length Crimp Diameter Approx. Actual
mm mm mm in
NOTE: Die and dial settings are approximate recommendations. Ferrules should be crimped with
PUL 153 00 the largest diameter die set available to make the ridges on the finished crimp as small as
possible. All crimp dimensions must be verified with a calibrated measuring device.
Printed: 24-Feb-23
CRIMP SPECIFICATIONS
Crimper Hose Coupling Crimp Instructions CHART NUMBER 80 REV 00
Finn-Power 154 8400 Interlock Tolerance +/- 0.1mm or +/- 0.004 inches .
32 Series
Cover Tube
Skive Skive Crimp Dial Setting
Hose Ferrule length Length Die Length Crimp Diameter Approx. Actual
mm mm mm in
NOTE: Die and dial settings are approximate recommendations. Ferrules should be crimped with
PUL 154 00 the largest diameter die set available to make the ridges on the finished crimp as small as
possible. All crimp dimensions must be verified with a calibrated measuring device.
Printed: 24-Feb-23
CRIMP SPECIFICATIONS
Crimper Hose Coupling Crimp Instructions CHART NUMBER 143 REV 00
Finn-Power 155 8500 Interlock Tolerance +/- 0.1mm or +/- 0.004 inches .
32 Series
Cover Tube
Skive Skive Crimp Dial Setting
Hose Ferrule length Length Die Length Crimp Diameter Approx. Actual
mm mm mm in
NOTE: Die and dial settings are approximate recommendations. Ferrules should be crimped with
PUL 155 00 the largest diameter die set available to make the ridges on the finished crimp as small as
possible. All crimp dimensions must be verified with a calibrated measuring device.
Printed: 24-Feb-23
CRIMP SPECIFICATIONS
Crimper Hose Coupling Crimp Instructions CHART NUMBER 152 REV 00
Finn-Power 653 4400 One-piece Mark the hose at a distance from the end of the hose equal to the "Insertion Length". Install the
fitting on the hose so that the mark is even with the end of the ferrule. Crimp the entire length of
32 Series the ferrule to the Crimp Diameter given in the table. Tolerance +0.1mm/- 0.2mm or + 0.004/-0.008
inches.
Cover Over
Skive Ferrule Crimp Dial Setting
Hose Ferrule Length Crimp Die Length Crimp Diameter Approx. Actual
mm mm in
653 -06 4400 26 34 32-22 Full 22.8 0.898 0.8
653 -08 4400 33 36 32-22 Full 24.9 0.980 2.9
653 -12 4400 38 43 32-34 Full 34.1 1.343 0.1
653 -16 4400 49 52 32-39 Full 42.3 1.665 3.3
NOTE: Die and dial settings are approximate recommendations. Ferrules should be crimped with
IT54 00 the largest diameter die set available to make the ridges on the finished crimp as small as
possible. All crimp dimensions must be verified with a calibrated measuring device.
Printed: 24-Feb-23
CRIMP SPECIFICATIONS
Crimper Hose Coupling Crimp Instructions CHART NUMBER 127 REV 00
Finn-Power 115 8600 Interlock Tolerance +0.1mm/- 0.2mm or + 0.004/-0.008 inches .
32 Series
Cover Tube
Skive Skive Crimp Dial Setting
Hose Ferrule Length Length Die Length Crimp Diameter Approx. Actual
mm mm mm in
NOTE: Die and dial settings are approximate recommendations. Ferrules should be crimped with
IT37 00 the largest diameter die set available to make the ridges on the finished crimp as small as
possible. All crimp dimensions must be verified with a calibrated measuring device.
Printed: 24-Feb-23
CRIMP SPECIFICATIONS
Crimper Hose Coupling Crimp Instructions CHART NUMBER 138 REV 00
Finn-Power 115 9600 One-piece Cover must be removed before the fittings can be attached. Leave a section of ferrule nearest
thread end of fitting uncrimped,crimp only to the position described in "Crimp Length". Crimp
32 Series diameter tolerance +/- 0.1mm.
Cover
Skive Crimp Dial Setting
Hose Ferrule Length Die Length Crimp Diameter Approx. Actual
mm mm in
NOTE: Die and dial settings are approximate recommendations. Ferrules should be crimped with
IT45 00 the largest diameter die set available to make the ridges on the finished crimp as small as
possible. All crimp dimensions must be verified with a calibrated measuring device.
Printed: 24-Feb-23
CRIMP SPECIFICATIONS
Crimper Hose Coupling Crimp Instructions CHART NUMBER 104 REV 00
Finn-Power 115 5000 Non-Skive Tolerance + 0.1/-0.2mm or + 0.004/-0.008 inches .
32 Series
Cover
Skive Crimp Dial Setting
Hose Ferrule Length Die Length Crimp Diameter Approx. Actual
mm mm in
NOTE: Die and dial settings are approximate recommendations. Ferrules should be crimped with
IT19 00 the largest diameter die set available to make the ridges on the finished crimp as small as
possible. All crimp dimensions must be verified with a calibrated measuring device.
Printed: 24-Feb-23
CRIMP SPECIFICATIONS
Crimper Hose Coupling Crimp Instructions CHART NUMBER 107 REV 00
Finn-Power 115 5000 Skive Tolerance + 0.1/-0.2mm or + 0.004/-0.008 inches .
32 Series
Cover
Skive Crimp Dial Setting
Hose Ferrule Length Die Length Crimp Diameter Approx. Actual
mm mm in
NOTE: Die and dial settings are approximate recommendations. Ferrules should be crimped with
IT22 00 the largest diameter die set available to make the ridges on the finished crimp as small as
possible. All crimp dimensions must be verified with a calibrated measuring device.
Printed: 24-Feb-23
CRIMP SPECIFICATIONS
Crimper Hose Coupling Crimp Instructions CHART NUMBER 93 REV 01
Finn-Power 115 4400 One-piece Mark the hose at a distance from the end of the hose equal to the "Insertion Length". Install the
fitting on the hose so that the mark is even with the end of the ferrule. Crimp the entire length of
32 Series the ferrule to the Crimp Diameter given in the table. Tolerance +0.1mm/- 0.2mm or + 0.004/-0.008
inches.
Fitting
Insertion Crimp Dial Setting
Hose Ferrule Length Die Length Crimp Diameter Approx. Actual
mm mm in
NOTE: Die and dial settings are approximate recommendations. Ferrules should be crimped with
IT11 01 the largest diameter die set available to make the ridges on the finished crimp as small as
possible. All crimp dimensions must be verified with a calibrated measuring device.
Printed: 24-Feb-23
CRIMP SPECIFICATIONS
Crimper Hose Coupling Crimp Instructions CHART NUMBER 94 REV 00
Finn-Power 115 4400 One-piece Mark the hose at a distance from the end of the hose equal to the "Insertion Length". Install the
fitting on the hose so that the mark is even with the end of the ferrule. Crimp the entire length of
32 Series the ferrule to the Crimp Diameter given in the table. Tolerance +0.1mm/- 0.2mm or + 0.004/-0.008
inches.
Cover
Skive Crimp Dial Setting
Hose Ferrule Length Die Length Crimp Diameter Approx. Actual
mm mm in
NOTE: Die and dial settings are approximate recommendations. Ferrules should be crimped with
IT11A 00 the largest diameter die set available to make the ridges on the finished crimp as small as
possible. All crimp dimensions must be verified with a calibrated measuring device.
Printed: 24-Feb-23
CRIMP SPECIFICATIONS
Crimper Hose Coupling Crimp Instructions CHART NUMBER 145 REV 01
Finn-Power 113 5000 Skive Tolerance + 0.1/-0.2mm or + 0.004/-0.008 inches .
32 Series
Cover
Skive Crimp Dial Setting
Hose Ferrule Length Die Length Crimp Diameter Approx. Actual
mm mm in
NOTE: Die and dial settings are approximate recommendations. Ferrules should be crimped with
IT48 01 the largest diameter die set available to make the ridges on the finished crimp as small as
possible. All crimp dimensions must be verified with a calibrated measuring device.
Printed: 24-Feb-23
CRIMP SPECIFICATIONS
Crimper Hose Coupling Crimp Instructions CHART NUMBER 68 REV 01
Finn-Power 132 5000 Non-Skive Tolerance + 0.1/-0.2mm or + 0.004/-0.008 inches .
32 Series
NOTE: Die and dial settings are approximate recommendations. Ferrules should be crimped with
5/G/U/TA/110 01 the largest diameter die set available to make the ridges on the finished crimp as small as
possible. All crimp dimensions must be verified with a calibrated measuring device.
Printed: 24-Feb-23
CRIMP SPECIFICATIONS
Crimper Hose Coupling Crimp Instructions CHART NUMBER 59 REV 07
Finn-Power 151 5000 Non-Skive Tolerance + 0.1/-0.2mm or + 0.004/-0.008 inches .
32 Series
Crimp
Insert Crimp Dial Setting
Hose Ferrule Size Die Length Crimp Diameter Approx. Actual
mm in
5503-03
151 -04 -03 32-14 Full 15.5 0.610 1.5
5503-04
151 -05 -04 32-16 Full 17.4 0.685 1.4
5503-05
151 -06 -05 32-19 Full 20.8 0.819 1.8
5503-06
151 -08 -06 32-19 Full 20.0 0.787 1.0
5503-08
151 -10 -08 32-22 Full 24.9 0.980 2.9
5503-10
151 -12 -10 32-30 Full 30.4 1.197 0.4
5503-12
151 -16 -14 32-34 Full 34.8 1.370 0.8
5503-16
151 -20 -18 32-39 Full 44.1 1.736 5.1
5503-20
151 -24 -22 32-45 Full 47.2 1.858 2.2
5901-32
151 -32 -29 32-57 Full 62.7 2.468 5.7
NOTE: Die and dial settings are approximate recommendations. Ferrules should be crimped with
5/G/U/TA/116 07 the largest diameter die set available to make the ridges on the finished crimp as small as
possible. All crimp dimensions must be verified with a calibrated measuring device.
Printed: 24-Feb-23
CRIMP SPECIFICATIONS
Crimper Hose Coupling Crimp Instructions CHART NUMBER 67 REV 02
Finn-Power 141 5000 Non-Skive Tolerance + 0.1/-0.2mm or + 0.004/-0.008 inches .
32 Series
NOTE: Die and dial settings are approximate recommendations. Ferrules should be crimped with
AG111 02 the largest diameter die set available to make the ridges on the finished crimp as small as
possible. All crimp dimensions must be verified with a calibrated measuring device.
Printed: 24-Feb-23
CRIMP SPECIFICATIONS
Crimper Hose Coupling Crimp Instructions CHART NUMBER 48 REV 00
Finn-Power 170 9700 Non-Skive Leave a section of ferrule nearest thread end of fitting uncrimped, crimp only to the position
described in "Crimp Length". Crimp diameter tolerance +/- 0.1mm.
32 Series
Fitting
Insertion Crimp Dial Setting
Hose Ferrule Length Die Length Crimp Diameter Approx. Actual
mm mm in
NOTE: Die and dial settings are approximate recommendations. Ferrules should be crimped with
PUL170 00 the largest diameter die set available to make the ridges on the finished crimp as small as
possible. All crimp dimensions must be verified with a calibrated measuring device.
Printed: 24-Feb-23
CRIMP SPECIFICATIONS
Crimper Hose Coupling Crimp Instructions CHART NUMBER 70 REV 03
Finn-Power 136 9500 One Piece Mark the hose at a distance from the end of the hose equal to the "Insertion Length". Install the
fitting on the hose so that the mark is even with the end of the ferrule. Crimp the entire length of
32 Series the ferrule to the Crimp Diameter given in the table. Tolerance +0.1mm/- 0.2mm or + 0.004/-0.008
inches
..
CAUTION: REVISED CRIMP SPECIFICATIONS FOR 9500-20 FITTINGS ONLY
Fitting
Insertion Crimp Dial Setting
Hose Ferrule Length Die Length Crimp Diameter Approx. Actual
mm mm in
NOTE: Die and dial settings are approximate recommendations. Ferrules should be crimped with
5/G/U/TA/127 03 the largest diameter die set available to make the ridges on the finished crimp as small as
possible. All crimp dimensions must be verified with a calibrated measuring device.
Printed: 24-Feb-23
CRIMP SPECIFICATIONS
Crimper Hose Coupling Crimp Instructions CHART NUMBER 71 REV 01
Finn-Power 115 9500 One-pieceN Mark the hose at a distance from the end of the hose equal to the "Insertion Length". Install the
fitting on the hose so that the mark is even with the end of the ferrule. Crimp the entire length of
32 Series the ferrule to the Crimp Diameter given in the table. Tolerance +0.1mm/- 0.2mm or + 0.004/-0.008
inches
..
CAUTION: REVISED CRIMP SPECIFICATIONS FOR 9500-20 FITTINGS ONLY
Fitting
Insertion Crimp Dial Setting
Hose Ferrule Length Die Length Crimp Diameter Approx. Actual
mm mm in
NOTE: Die and dial settings are approximate recommendations. Ferrules should be crimped with
5/G/U/TA/128 01 the largest diameter die set available to make the ridges on the finished crimp as small as
possible. All crimp dimensions must be verified with a calibrated measuring device.
Printed: 24-Feb-23
CRIMP SPECIFICATIONS
Crimper Hose Coupling Crimp Instructions CHART NUMBER 163 REV 00
Finn-Power 156 8600 Interlock Tolerance +0.1mm/- 0.2mm or + 0.004/-0.008 inches .
32 Series
PLUS
Cover Tube
Skive Skive Crimp Dial Setting
Hose Ferrule Length Length Die Length Crimp Diameter Approx. Actual
mm mm mm in
156 PLUS -12 8640 52 15 32-30 Full 33.7 1.327 3.7
156 PLUS -16 8640 65 17 32-39 Full 41.2 1.622 2.2
156 PLUS -20 8660 74 21.5 32-51 Full 53.5 2.106 2.5
156 PLUS -24 8660 81 22 32-57 Full 60.3 2.374 3.3
156 PLUS -32 8660 85 29 32-74 Full 77.9 3.067 3.9
NOTE: Die and dial settings are approximate recommendations. Ferrules should be crimped with
IT62 00 the largest diameter die set available to make the ridges on the finished crimp as small as
possible. All crimp dimensions must be verified with a calibrated measuring device.
Printed: 24-Feb-23