Professional Documents
Culture Documents
STAINLESS STEEL
HIGH PRESSURE 37°
TUBE FITTINGS
1/8’’ TO 2’’
MEETS SAE STANDARD J514
If required, see SAE Standard J514 for a TUBING DATA FOR 37° TUBE HANDLING
complete list of dimensions. FLARE THREE-PIECE TUBE Scratches on the tube might cause leaks.
NPT Tapered Pipe Threads meet the ASSEMBLY It is, therefore, important to handle the
A requirements of ASME/ANSI B.I.20.1. tube carefully to reduce the risk of leaks.
In order to ensure maximum fitting
reliability and performance, please take 1. Tubes must not be dragged on the
great care when selecting the tube for floor.
All 37° Flared tube fittings 3-piece each application. 2. Tubes must not be dragged out of a
tube assembly can be used with Tubing should be fully annealed, tubing rack, especially in cases
metric tube by using a metric 37° seamless and drawn, suitable for of large OD tubes.
sleeve, instead of an inch sleeve. bending and flaring, according to
B standard ASTM-269, TUBE CUTTING
Each dimension table shows which
A.I.S.I. 316 or 304. Two different methods can be used to
metric sleeve should be used for cut tubes:
every size. 1. Tube cutter
QUALITY 2. Hacksaw
Lengths of finished tubing should be
ASSEMBLY INSTRUCTIONS reasonably straight and have smooth Tube cutter
ends, free from burrs. Tubing should be To attain a leakfree connection,
C free from scale and injurious defects, the tubing must be cut squarely.
1. Cut the tube to the proper length.
2. Slide the nut and sleeve onto the tube. and it should have a workmanlike finish. A good quality tube cutter with an
(see Fig.1). Surface imperfections such as handling appropriate blade for tubing material is
3. With a special flaring tool, form the marks, die marks, or shallow pits will recommended.
flare to 37° dimension according to SAE not be considered injurious defects Do not try to reduce the time of cutting
STD. J533. (see Fig.2 page 91). provided the imperfections are within by taking deep cuts with each turn of
4. Screw the nut onto the body until the tolerances specified for diameter the cutter.
D finger tight. and wall thickness. The removal of such The end of the tube must be deburred to
5. From this position, tighten the nut with imperfections is not required. (Quality avoid damage to the fitting and to ensure
a wrench 1/4” turn in order to make a SAE J524). that the tube reaches the bottom of the
leakproof metal-to-metal connection. fitting.
Hacksaw cutting
In order to cut the tube with a hacksaw
E and to attain square ends, the tube must
be cut with guide blocks. This method
of cutting requires deburring of the tube
ends.
WARNING
Do not hold the tube in a vise in the place
where it will be inserted into the fitting.
F The vise will leave a mark on the tube
that may cause leaks and might cause
ovality.
Figure 2
TABLE 1: FLARING
Nominal A R S DEBURRING PRIOR
Tube O.D Single flare diameter A
TO FLARING
inch mm inch mm inch mm
Max Min Max Min ±0.02 ±0.5 Max Min
1/8 0.20 0.18 5.08 4.58 0.03 0.8 0.035 0.88 To ensure satisfactory flare
production, tube end deburring
3/16 0.28 0.26 7.11 6.61 0.03 0.8 0.035 0.88 might be required prior to flaring.
1/4 0.36 0.34 9.14 8.64 0.03 0.8 0.065 1.65 It is usually necessary to break
5/16 0.43 0.40 10.92 10.16 0.03 0.8 0.065 1.65 the inside corner smoothly before
single flaring. In addition, some B
3/8 0.49 0.46 12.44 11.69 0.04 1.0 0.065 1.65 non-ferrous tubing is normally
1/2 0.66 0.63 16.76 16.01 0.06 1.5 0.083 2.1 required to eliminate the cutoff
burr, which might otherwise create
5/8 0.79 0.76 20.06 19.31 0.06 1.5 0.095 2.41
leakage paths across a substantial
3/4 0.95 0.92 24.13 23.37 0.08 2.0 0.109 2.76 portion of the flare. Smoothly
7/8 1.07 1.04 27.17 26.42 0.08 2.0 0.109 2.76 breaking the outside corner prior
to single flaring, or both the outside
1 1.20 1.17 30.48 29.72 0.09 2.3 0.12 3.04 C
and inside corners prior to double
1 1/8 1.38 1.35 35.05 34.29 0.09 2.3 0.12 3.04 flaring, is acceptable for any tube
1 1/4 1.51 1.48 38.35 37.60 0.09 2.3 0.12 3.04 material to minimize splitting.
1 1/2 1.73 1.70 43.94 43.18 0.11 2.8 0.12 3.04
Dimensions are for reference only, and subject to change without notice.
D
TABLE 2: ALLOWABLE WORKING PRESSURE RATINGS
(CAPABLE OF 4’’ TO 1’’ MIN. BURST)
Nom. SAE Nom. Tube O.D 37° Flare Nom. Pipe SAE St.Threads Fittings with NOTE:
Dash Size Inches Straight Thread Size Union and Pipe Threads
Bulkhead
E
2 1/8 5/16" - 24 1/8" 5000 5000
As many factors influence the
3 3/16 3/8" - 24 1/8" 5000 5000 pressure at which a system will
4 1/4 7/16" - 20 1/8" 5000 5000 or will not perform satisfactorily,
5 5/16 1/2" - 20 1/8" 5000 5000 values shown in Table 2 should
not be construed as guaranteed
6 3/8 9/16" - 18 1/4" 5000 5000 minimum.
8 1/2 3/4" - 16 3/8" 4500 4000 F
10 5/8 7/8" - 14 1/2" 3500 3000
12 3/4 1 1/16" - 12 3/4" 3500 3000
14 7/8 1 3/16" - 12 3/4" 3000 2500
16 1 1 5/16" - 12 1" 3000 2000
20 1 1/4 1 5/8" - 12 1 1/4" 2500 1150
24 1 1/2 1 7/8" - 12 1 1/2" 2000 1000 G
32 2 2 1/2" - 12 2" 1500 1000
SLEEVE______________________ 123 FEMALE CONNECTOR ____ 128 FEMALE RUN TEE _____________ 135
For 3-piece tube assembly S.A.E. 070103 S.A.E. 070426
S.A.E. 070115 746HF 771HFL
A 740HF
NUT__________________________ 123 MALE CONNECTOR _______ 129 FEMALE BRANCH TEE ________ 136
For 3-piece tube assembly S.A.E. 070102 S.A.E. 070427
S.A.E. 070110 748HF 772HFL
B 741HF
REDUCING ADAPTER______ 124 MALE CONNECTOR _______ 130 BULKHEAD UNION ____________ 137
S.A.E. 070123 S.A.E. 0701120 S.A.E. 070601
741HFL 748HOB 774HFL
C
UNION _______________________ 125 MALE ELBOW ______________ 131 BULKHEAD LOCKNUT ________ 137
S.A.E. 070101 S.A.E. 070202 S.A.E. 070118
742HF 749HF 774HFLN
D
LARGE HEX UNION_________ 125 FEMALE ELBOW ___________ 132 CROSS __________________________ 138
S.A.E. 070119 S.A.E. 070203 S.A.E. 070501
742HFL 750HF 7102HFL
E
UNION TEE__________________ 126 MALE RUN TEE ____________ 133 TUBE PLUG ____________________ 139
S.A.E. 070401 S.A.E. 070424 S.A.E. 070109
744HF 751HF 7639HF
MALE BRANCH TEE________ 127 UNION ELBOW _____________ 134 CAP______________________________ 139
S.A.E. 070425 S.A.E. 070201 S.A.E. 070112
745HF 755HF 7640HF
All 37° Flared tube fittings 3-piece tube assembly can be used with metric tube by using a metric 37° sleeve, instead of an inch sleeve. Each dimension table
shows which metric sleeve should be used for every size.
D
741 HF
NUT FOR 3-PIECE
TUBE ASSEMBLY
S.A.E. 070110
E
“D” Dimension is minimum opening. Dimensions are for reference only, and are subject to change without notice.
TUBE (INCH)
Ordering Tube O.D. B L
A Information UN
inch inch mm
741HFL SS 3/8'' X 1/4'' 3/8 to 1/4 7/16 - 20 0.97 24.6
741HFL SS 1/2'' X 1/4'' 1/2 to 1/4 7/16 - 20 1.00 25.4
741HFL SS 1/2'' X 3/8'' 1/2 to 3/8 9/16 - 18 1.00 25.4
741HFL SS 5/8'' X 1/4'' 5/8 to 1/4 7/16 - 20 1.03 26.2
741HFL SS 5/8'' X 3/8'' 5/8 to 3/8 9/16 - 18 1.03 26.2
B 741HFL SS 3/4'' X 1/4'' 3/4 to 1/4 7/16 - 20 1.09 27.7
741HFL SS 3/4'' X 3/8'' 3/4 to 3/8 9/16 - 18 1.09 27.7
741HFL SS 3/4'' X 1/2'' 3/4 to 1/2 3/4 - 16 1.19 30.2
741HFL SS 3/4'' X 5/8'' 3/4 to 5/8 7/8 - 14 1.66 42.1
741HFL SS 7/8'' X 3/8'' 7/8 to 3/8 9/16 - 18 1.13 28.7
741HFL SS 7/8'' X 5/8'' 7/8 to 5/8 7/8 - 14 1.33 33.7
C
741HFL SS 7/8'' X 3/4'' 7/8 to 3/4 1 1/16 - 12 1.84 46.7
741HFL SS 1'' X 3/4'' 1 to 3/4 1 1/16 - 12 1.47 37.3
741HFL SS 1'' X 7/8'' 1 to 7/8 1 3/16 - 12 1.91 48.5
741HFL SS 1 1/4'' X 3/4'' 1 1/4 to 3/4 1 1/16 - 12 1.53 38.8
741HFL SS 1 1/4'' X 1'' 1 1/4 to 1 1 5/16 - 12 1.59 40.3
D 741HFL SS 1 1/2'' X 1 1/4'' 1 1/2 to 1 1/4 1 5/8 - 12 1.69 42.9
TUBE (MM)
Ordering Tube O.D. B L
Information UN
inch to mm inch mm
E 741HFL SS 3/8'' X 6MM 3/8 to 6 7/16 - 20 0.97 24.6
741HFL SS 1/2'' X 6MM 1/2 to 6 7/16 - 20 1.00 25.4
741HFL SS 1/2'' X 10MM 1/2 to 10 9/16 - 18 1.00 25.4
741HFL SS 5/8'' X 6MM 5/8 to 6 7/16 - 20 1.03 26.2
741HFL SS 5/8'' X 10MM 5/8 to 10 9/16 - 18 1.03 26.2
741HFL SS 5/8'' X 12MM 5/8 to 12 3/4 - 16 1.44 36.5
F 741HFL SS 3/4'' X 6MM 3/4 to 6 7/16 - 20 1.09 27.7
741HFL SS 3/4'' X 10MM 3/4 to 10 9/16 - 18 1.09 27.7
741HFL SS 3/4'' X 12MM 3/4 to 12 3/4 - 16 1.19 30.2
741HFL SS 3/4'' X 16MM 3/4 to 16 7/8 - 14 1.66 42.1
741HFL SS 7/8'' X 10MM 7/8 to 10 9/16 - 18 1.13 28.7
741HFL SS 7/8'' X 16MM 7/8 to 16 7/8 - 14 1.33 33.7
G 741HFL SS 7/8'' X 18MM 7/8 to 18 1 1/16 - 12 1.84 46.7
741HFL SS 1'' X 18MM 1 to 18 1 1/16 - 12 1.47 37.3
741HFL SS 1'' X 20MM 1 to 20 1 3/16 - 12 1.91 48.5
741HFL SS 1 1/4'' X 18MM 1 1/4 to 18 1 1/16 - 12 1.53 38.8
741HFL SS 1 1/4'' X 25MM 1 1/4 to 25 1 5/16 - 12 1.59 40.3
741HFL SS 1 1/2'' X 32MM 1 1/2 to 32 1 5/8 - 12 1.69 42.9
H
“D” Dimension is minimum opening. Dimensions are for reference only, and are subject to change without notice.
D
742 HFL
LARGE HEX UNION
S.A.E. 070119
“D” Dimension is minimum opening. Dimensions are for reference only, and are subject to change without notice.
“D” Dimension is minimum opening. Dimensions are for reference only, and are subject to change without notice.
“D” Dimension is minimum opening. Dimensions are for reference only, and are subject to change without notice.
“D” Dimension is minimum opening. Dimensions are for reference only, and are subject to change without notice.
“D” Dimension is minimum opening. Dimensions are for reference only, and are subject to change without notice.
Dimensions are for reference only, and are subject to change without notice.
Dimensions are for reference only, and are subject to change without notice.
“D” Dimension is minimum opening. Dimensions are for reference only, and are subject to change without notice.
“D” Dimension is minimum opening. Dimensions are for reference only, and are subject to change without notice.
“D” Dimension is minimum opening. Dimensions are for reference only, and are subject to change without notice.
“D” Dimension is minimum opening. Dimensions are for reference only, and are subject to change without notice.
“D” Dimension is minimum opening. Dimensions are for reference only, and are subject to change without notice.
774 HFLN
BULKHEAD LOCKNUT D
S.A.E. 070118
“D” Dimension is minimum opening. Dimensions are for reference only, and are subject to change without notice.
“D” Dimension is minimum opening. Dimensions are for reference only, and are subject to change without notice.
7640 HF
D
CAP B
S.A.E. 070112
“D” Dimension is minimum opening. Dimensions are for reference only, and are subject to change without notice.
Dimensions are for reference only, and are subject to change without notice.