Professional Documents
Culture Documents
(Alternative Form for Single Chamber, Completely Shop or Field Fabricated Vessels Only)
Shop Order Number
As Required by the Provisions of the ASME Boiler and Pressure Vessel Code Rules, Section VIII, Division 1 Page 1 of 2
1. Manufactured and certified by Svifflug, S. de R.L. de C.V., Huehuetoca Plant, Calzada de Marisoles Lote 1, Ex-Hacienda de Jalpa, Huehuetoca,
Estado de Mexico, C.P. 54683, Mexico
(Name and address of Manufacturer)
2. Manufactured for Svifflug S de RL de CV, Monte Pelvoux No. 111, 7° Piso, Lomas de Chapultepec, México, CDMX.
(Name and address of Purchaser)
3. Location of Installation NOT KNOWN
(Name and address)
Min Hub
Type ID OD Flange Thk Material How Attached
Bolting
Thk
Location Num & Size Bolting Material
Washer (OD,
Washer Material
ID, thk)
(a) N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A
11. Supports: Skirt NO Lugs 2 Legs 4 Other NO Attached WELDED TO SHELL AND HEADS
(Yes or no) (Number) (Number) (Describe) (Where and how)
12. Remarks: Manufacturer's Partial Data Reports properly identified and signed by Commissioned Inspectors, have been furnished for the following items of the report:
N/A
(Name of part, item number, Manufacturer's name and identifying stamp)
HORIZONTAL PRESSURE VESSEL, 500 WG AG DOMESTIC TANK TO BE USED FOR NON-CORROSIVE SERVICE.
CONSTRUCTED UNDER THE PROVISIONS OF UG-90 (C)(2)
IMPACT TESTING EXEMPTED PER UG-20(f).
JOINT EFFICIENCY IS 0.80 BETWEEN HEADS/SHELL ACCORDING TO TABLE UW-12 FOR THE DESIGN
CALCULATION.
SPOT PER UW-11(b) BETWEEN HEADS/SHELL (LONG SEAM) RT4.
JOINT CONNECTING HEMISPHERICAL HEADS TO SHELL ACCORDING TO FIG. UW-9-3.
OVER PRESSURE PROTECTION BY OTHERS.
Additional Remarks - See Attached U-4...
FORM U-1A Page 2 of 2
Manufactured by Svifflug, S. de R.L. de C.V., Huehuetoca Plant, Calzada de Marisoles Lote 1, Ex-Hacienda de Jalpa, Huehuetoca, Estado
de Mexico, C.P. 54683, Mexico
Manufacturer's Serial No. H2301476 thru H2301491 CRN N/A National Board No. H2301476-H2301491
Vessel constructed by Svifflug, S. de R.L. de C.V., Huehuetoca Plant at de Mexico, C.P. 54683, Mexico
I, the undersigned, holding a valid commission issued by The National Board of Boiler and Pressure Vessel Inspectors and employed by
Bureau Veritas Inspection and Insurance Company, of Lynn, MA
have inspected the component described in this Manufacturer's Data Report on February 11, 2023 ,
and state that, to the best of my knowledge and belief, the Manufacturer has constructed this pressure vessel in accordance with ASME BOILER
AND PRESSURE VESSEL CODE, Section VIII, Division 1. By signing this certificate neither the Inspector nor his/her employer makes any
warranty, expressed or implied, concerning the pressure vessel described in this Manufacturer's Data Report. Furthermore, neither the Inspector
nor his/her employer shall be liable in any manner for any personal injury or property damage or a loss of any kind arising from or connected with
this inspection.
1. Manufactured and certified by Svifflug, S. de R.L. de C.V., Huehuetoca Plant, Calzada de Marisoles Lote 1, Ex-Hacienda de Jalpa, Huehuetoca,
Estado de Mexico, C.P. 54683, Mexico
(Name and address of Manufacturer)
2. Manufactured for Svifflug S de RL de CV, Monte Pelvoux No. 111, 7° Piso, Lomas de Chapultepec, México, CDMX.
(Name and address of Purchaser)
Additional Remarks:
PRESSURE VESSEL DESIGN MANUAL-4TH EDITION BY DENNIS R.MOSS AND MICHAEL BASIC, WAS USED FOR THE
CALCULATION OF LEGS AND LUGS.
SHOP ORDER: 157136
Certificate of Authorization: Type "U" No. 21957 Expires September 13, 2025