Professional Documents
Culture Documents
NAME:________________________________________________________SECTION:________
I. Multiple Choice: Read each statement carefully. Then, Write the letter of the
correct answer on the space provided. Use capital letter only and no erasures.
_____ 8. If the voltage is constant or the same in each component. What kind of circuit is
this?
A. Parallel Circuit B. Series Circuit
C. Complex Circuit D. Simple Circuit
_ 9. What will happen if L1 and L2 is in contact without passing any load?
A. It will cause an explosion B. Nothing happens
C. The line will spark only D. It will produce more voltage
_ 10. Mark switch on the switch in his room to turn on the light but the light does not
light up. What do you think happen?
A. The circuit is grounded B. The circuit is open
C. The circuit is open D. The circuit is overloaded
_11. What will be the best tools to use, if you want to mount junction box in a
wooden wall?
A. Screwdriver B. Hammer C. Pliers D. Gimlet
_12. To remove the insulator of the TW #18 AWG solid cu. wire, what is the best
tool to use?
A. Pliers B. Wire stripper C. Blade cutter D. Hickey
_13. This is tools used in driving or pounding and pulling out nails.
A. Ballpeen hammers B. Claw hammer
C. Mallet (rubber head) D. Stubby screwdriver
_14. A small drilling machine with a chuck capacity of ¼‖ to 3/8‖. It is used in
making holes on metal sheets and concrete walls.
A. Electric power drill B. Portable electric drill
C. Power saw D. Portable grinder
_15. Johnny wants to bend a plastic pipe in 90degree. What is the best power tools
to use?
A. Electric stove B. Heat gun
C. Lighter D. Gas stove
_16. This is a metal box where all circuit breaker place.
A. Junction box B. Square box
C. Utility box D. Panel board
_17. An electrical material used as the passage of wires for protection and insulation?
A. Connectors B. Clamps
C. Conduits D. Male plug
_18. It is used to attach metallic or non-metallic conduit to the junction or utility
boxes.
A. Connectors B. Clamps
C. Conduits D. Male plug
_19. This is a protective device used to automatically in trip position when trouble in
the circuit such as short circuit or overload occurs.
A. Circuit breaker B. Fuse
C. Electrical tape D. Bulb
_20. It is an octagonal shaped electrical material where the connections or joints of
wires are being done? It is also where the flush type lamp holder is attached.
A. Junction box B. Square box
C. Utility box D. Panel board
II.Directions: Read the statement carefully and identify what is being described or defined. Choose
your answer from the words inside the box.
_________1. This is used for griping, holding, cutting electrical wires and cables and even small
nails. Usually used by linemen in doing heavy tasks.
_________2. Used for cutting and holding fine wires. This can reach tight space or small opening
where other pliers cannot reach and also used in making terminal loops of copper wires.
_________3. This has a cross tip resembling a positive (+) sign. It is used to drive screws with cross
slot heads.
_________4. This is tools used in driving or pounding and pulling out nails.
_________5. A tool used for removing insulation of medium sized wires ranging from gauge #10
to gauge #16.
_________6. A small drilling machine with a chuck capacity of ¼‖ to 3/8‖. It is used in making holes
on metal sheets and concrete walls.
_________7. Comes in either Standard or Philips screw driver with short shank or blade and shorted
handle used to turn screws in tight space where standard screw driver cannot be used.
__________8. Used by linemen to remove insulation of wire and cables in low and high
voltage transmission lines.
__________10. This is a circuit protective device that automatically blows and cut the
current when an over load or short circuit happens.
__________12. Are electrical materials used as the passage of wires for protection and
Insulation.
__________13. Are used to attach metallic or non-metallic conduit to the junction or utility
boxes.
__________14. This is a protective device used to automatically cut off the current when
trouble in the circuit such as short circuit or over load occurs.
III.SOLVE THE FOLLOWING PROBLEMS AND SHOW YOUR SOLUTIONS: (5 PTS. EACH)
Problem (1): An alarm clock draws 0.5 A of current when connected to a 120 V circuit. Find its
resistance.
Problem (2): How much current is drawn from a circuit with a resistor of 1000 ohms if powered by a
battery with 1.5 volts?
Problem (3): An electric heater has a coiled metal wire that draws a current of 100 A. The resistance of
the wire is 1.1 ohms. Calculate the voltage that must be established for it.
Prepared by:
I. Multiple Choice:
1. C
2. C
3. D
4. B
5. C
6. A
7. B
8. A
9. A
10. B
11. A
12. B
13. B
14. B
15. B
16. D
17. C
18. C
19. A
20. A
II. Identification
1. Combination Pliers
2. Long Nose Pliers
3. Philips Screw driver
4. Claw Hammer
5. Wire Stripper
6. Portable electric drill
7. Stubby screw driver
8. Electrician’s knife
9. Male plug
10. Fuse
11. Utility box
12. Conduits
13. Connectors
14. Circuit Breaker
15. Junction box
1.
2.
3.