Professional Documents
Culture Documents
KETTLER
confidential document 21.9.2009 1 of 4
07884-000 MARATHON ST
SETUP MODE
Initial State
Stop+Slow
U16(Km) U10(Mile)
Stop
Initial State
Incline calibration
Initial State
OK
Stop+Fast Fast+Slow+Stop
KETTLER
confidential document 21.9.2009 2 of 4
07884-000 MARATHON ST
SERVICE MODE
When incline motor needs calibration:
1.When controller changed.
START / ENTER
2.When incline motor is changed.
CALIBRATION
3.Press the STOP and SPEED- buttons at the same SPEED - / + (SLOW/ FAST)
time, then the buttons STOP and SPEED+, then the
SPEED- button. The treadmill is in calibration mode. ELEVATION - / + (DOWN / UP)
Press the START button. The treadmill will run
calibration for the incline motor.
NOTE: If error 5 appears, it means the controller
remembers a different value, so we need to bypass
the controller to calibrate the incline motor. In that
case, we have to disconnect the incline sensor cable
to bypass the old memory (Please refer to WIRING
DIAGRAM – Section IV, page 7). Then calibration
can be done properly.
KETTLER
confidential document 21.9.2009 3 of 4
07884-000 MARATHON ST
ERROR CODE
Error Code Error category When it happens. Follow up and send the information to KETTLER
Safety key Check Safety key If it happens frequently.
Check safety key cable and switch. - Open the plastic and check.
Next check the signal cable between motor and console.
Change the console.
Er 01 Speed sensor Speed sensor is broken. Turn off and on the power.
Main power relay is broken(in the motor controller). Push Start key to test the treadmill.
Motor is broken or motor wire is badly connected. Warning : Do not step on the treadmill, it is very dangerous.
PWM circuit that is in console is broken. 1) Check if motor is running for short time.
Main cable is damaged. if NO.
Check motor wire connection, motor brush connection, motor itself.
Motor controller circuit or signal cable was broken.
PWM circuit that is in console was broken.
if YES
Speed sensor wire connection , or speed sensor was broken.
Speed sensor circuit that is in motor controller was broken.
Signal cable or console was broken.
Er 02 Over speed When treadmill runs faster than target speed. - Check Power circuit. Turn off and on the power.
When User kicks the treadmill belt faster intentionally. Start the treadmill and check if there are Error 41 or others.
Frequency is very low. Warning : Do not step on the treadmill, it is very dangerous.
It usually happens during workout(14Km/h to 16Km/H).
Er 06 Memory EEPROM of console error, eeprom problem or circuit problem. Turn off and on again. If it happens continually , you have to change the console.
Frequency is very low.
Er 08 Angle switch Angle switch broken. When Err 08 on the console, even if treadmill is not folded.
When the treadmill is folded. Check the cable connection first and then check the angle switch(motor control board).
Er 15 Under speed When treadmill runs slower than target speed. Turn off and on the power.
Motor is damaged. Push Start key to test the treadmill.
AC input is lower than normal value(lower than 210VAC), with heavy user. Warning : Do not step on the treadmill, it is very dangerous.
Deck and belt condition is not good.(Check silicone). During testing, if motor makes electric howling noise.
Check the motor condition and motor wires are tightly connected.
Check the condition of deck and belt, if deck and belt are damaged
you have to change the deck and belt , and lubricate it with silicone.
Er 05 Elevation Check incline sensor or motor. Turn off and on the power.
Er 51 Err 51,Err 52,Err 53 happen during self test or calibration. Calibrate the elevation motor again and check the console value.
Er 52 Push and hole 12%+ 6% keys together for 2seconds to calibrate the motor.
Er 53 Then treadmill goes up and goes down to the bottom, please check the value on the
it be more than 190 at the top, and it should be less than 40 at the bottom.
It should
Over acceleration
KETTLER
confidential document 21.9.2009 4 of 4