Professional Documents
Culture Documents
Backhoe Bobcat Service Manual
Backhoe Bobcat Service Manual
SERVICE MANUAL
Safety Alert Symbol: This symbol with a warning statement, means: “Warning, be alert! Your safety is
involved!” Carefully read the message that follows.
CORRECT WRONG
Never service the Bobcat Loader or Backhoe Always lower the backhoe attachment to the
without instructions. See Operation & ground before lubricating or servicing.
Maintenance and Service Manual.
Avoid contact with leaking hydraulic fluid or
Check engine and hydraulic fluids daily. diesel fuel under pressure. It can penetrate skin
or eyes.
Cleaning and maintenance are required daily.
Stop, cool and clean engine of flammable
Never service or adjust loader/backhoe with materials before checking fluids.
the engine running unless instructed to do so
in manual. Keep body, loose objects are clothing away from
moving parts, electrical contacts, hot parts and
Safety glasses are needed for eye protection from electrical arcs,
battery acid, compresses springs, fluids under pressure and
flying debris or when tools are used. Use eye protection approved
for type of welding.
MSW31-0805
3 of 176
4 of 176
Dealer Copy -- Not for Resale
905B 923SA 923S 928S 907 908B 909 911 730S 725S 835S 607 709 811 8709 911B 911C 913 914 914B
440
5 of 176
450
X
453
543
553 X X X
630
645 X X X X X
643
730
743 X X X X X X X X X
751
753
753H X X X X X X X X
753L
763 X X X
7753
773 X X X
843 X X X
853
853H
863 X X X X
873 X X
943 X
953 X X
963
X X
2400 X X
NOTE: Refer to the sales handbook for Backhoe mounting kit part numbers and serial numbers.
HYDRAULIC
CYLINDERS
SPECIFICATIONS
Backhoe
7 of 176 i Service Manual
Dealer Copy -- Not for Resale
Backhoe
8 of 176 ii Service Manual
MAIN FRAME SERVICE MAIN
FRAME
SERVICE
Page
Number
BACKHOE MOUNTING FRAME
Removal and Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1–14
BOOM AND ARM
Removal and Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1–14
LOCKING MECHANISM
Removal and Installation (607, 709, 709FDS, 8709, & 811) . . . . . . 1–22
LUBRICATION
905B Backhoe . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1–4
907 Backhoe . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1–5
909 Backhoe . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1–5
911 Backhoe . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1–5
913 & 914B Backhoe . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1–6
607 & 709 Backhoe . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1–7
709FDS, & 8709 Backhoe . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1–6
811 Backhoe . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1–8
725S & 730S Backhoe . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1–9
Backhoe
9 of 176 –1–1– Service Manual
Dealer Copy -- Not for Resale
Backhoe
10 of 176 –1–2– Service Manual
TROUBLESHOOTING
* The loader hydraulic system must be working properly for the attachments to operate as designed.
** Bobcat Fluid (P/N 6563328). If fluid is not available, use 10W–30/10W–40 Class SE Motor Oil for temperature above 0°
F (–18° C), 5W–30 Motor Oil for temperatures below 0° F (–18° C).
Backhoe
11 of 176 –1–3– Service Manual
LUBRICATION
A
B–07023
B 3
5 8
7
AVOID INJURY OR DEATH
Backhoe
12 of 176 –1–4– Service Manual
LUBRICATION (Cont’d)
A
3
4
2
9 5
Backhoe
13 of 176 –1–5– Service Manual
LUBRICATION (Cont’d)
A 4 3
2
9
1
5
AVOID INJURY OR DEATH
8
Always lower the Backhoe attachment to the
ground before lubricating or servicing [A].
W–2178–0295 10
7 6
Use only a high grade, multi–purpose, lithium base 11
lubricating grease. Add grease to the fittings until the extra
grease shows. 12
913 & 914 Backhoe 14
15
Lubricate the backhoe every 8 hours of operation [A]. 13
B–08154
Item Description (# of Fittings)
1. Arm Cylinder Base End (1)
2.
3.
Arm Pivot Busing (1)
Arm Cylinder Rod End (1)
B 3 6 13
Backhoe
14 of 176 –1–6– Service Manual
LUBRICATION (Cont’d)
A 2
2
1
P–13619
D
12
10
12 11
P–13621
Backhoe
15 of 176 –1–7– Service Manual
LUBRICATION (Cont’d)
A 12
3
2
AVOID INJURY OR DEATH CD–12812
Always lower the Backhoe attachment to the
ground before lubricating or servicing [A]. 4
W–2178–0295 6
Use only a high grade, multi–purpose, lithium base
lubricating grease. Add grease to the fittings until the extra
grease shows.
811 Backhoe
Lubricate the backhoe every 8 hours of operation [A] & [B]. 5
1
Item Description (# of Fittings) 7
1. Bucket Cylinder Rod End (3)
2. Bucket Cylinder Base End (1)
3. Arm Cylinder Rod End (1) 8
15
14
CD–11233 CD–12811
Backhoe
16 of 176 –1–8– Service Manual
LUBRICATION (Cont’d)
725S & 730S Backhoe
A 2
1
2
P–09847
D 12
12
9
13 12
11
10 11
P–09846
Backhoe
17 of 176 –1–9– Service Manual
LUBRICATION (Cont’d)
835S Backhoe
A WRONG
3
CD–12021
7
4
CD–12022
10
CD–12023
Backhoe
18 of 176 –1–10– Service Manual
LUBRICATION (Cont’d)
A 12
8
9
CD–07259
Backhoe
19 of 176 –1–11– Service Manual
SWING CHAIN (905)
Adjustment
A
Move the boom and arm to the center position. Lower the
bucket to the ground and stop the engine.
2
1
Loosen the jam nut (Item 1) [A] and loosen the adjustment
nut (Item 2) [A].
Tighten the adjustment nut (Item 2) [A] hand tight then one
full turn tighter.
Repeat the procedure to adjust the other chain.
Swing the backhoe boom both ways to check adjustment.
P–13518
If the boom swings further ony way, loosen the adjustment
nut on the side it swings the farthest and tighten the
adjustment nut an equal amount on the side that swings
shortest. B 3
Removal and Installation 1
P–13520
P–13519
P–13522
Backhoe
20 of 176 –1–12– Service Manual
SWING CHAIN (905) (Cont’d)
Removal and Installation (Cont’d)
A
Installation: Use the chain link tool MEL1037 (Item 1) [A] 1
and v–block MEL1037–60 (Item 2) [A] to press the
connector plate over the connector link.
NOTE: The force required for compression is 2
approximately 75 ft.–lbs. (102 Nm) torque. A
bench vise may be needed for compression.
P–13524
Rubber Stops
Hold the nuts located inside the rubber stops (Item 1) [C]
C
while removing the bolts (Item 1) [D] from the frame.
Tighten the nuts to 25–28 ft.–lbs. (34–38 Nm) torque. 1
P–13526
1 1
P–13525
Backhoe
21 of 176 –1–13– Service Manual
BOOM AND ARM
Removal And Installation
A
Backhoe must be securely attached to the loader to do
the following:
Move the boom, arm and bucket to the horizontal position
shown [A]. Block the boom and bucket as shown [A].
NOTE: The boom must be secure when removed from
the main frame.
BLOCK HERE
P–13581
Remove the pin (Item 2) [B] from the boom and the swing
frame.
C
NOTE: The mounting pins may be different on some
backhoes. The backhoe shown is 725S.
NOTE: It may be necessary to connect a chain hoist to
the boom to aid in pin removal.
Enter the loader, lower the seat bar and fasten the seat belt.
Drive the loader back slowly to disconnect the swing frame
from the boom, arm, and bucket assembly.
BACKHOE MOUNTING FRAME
Removal and Installation
CD–11225
Hook Mounted Backhoe: (607, 709, 709FDS, 8709, & 811)
NOTE: When the backhoe mounting frame is attached
to the loader, the swing frame can be removed. D
Release the backhoe frame locking levers to release the
backhoe main frame from the loader [C].
Disconnect the auxiliary couplers from the loader.
From the loader seat, raise the lift arms slightly to remove
the backhoe main frame weight from the loader mounting
hooks [D].
Tilt the Bob–Tach backward completely and raise the lift
arms until the backhoe frame pins are above the mounting
hooks [D].
P–09682
Backhoe
22 of 176 –1–14– Service Manual
BACKHOE MOUNTING FRAME (Cont’d)
Removal And Installation (Cont’d)
A
Hook Mounted Backhoe: (Cont’d)
Tilt the Bob–Tach forward and lower the lift arms until the
main frame rests on the ground [A].
P–09681
Tilt the Bob–Tach forward, lower the lift arms and back the
loader from the backhoe main frame.
Reverse the procedure to install the backhoe mounting
frame.
Backhoe
23 of 176 –1–15– Service Manual
BACKHOE MOUNTING FRAME (Cont’d)
Removal and Installation (Cont’d)
A 2
Ball Mounted Backhoe: (907, 909, 911, 725S, 730S, 835S,
923S, & 923SA) 1
Push down on the hand wheel lock (Item 1) [A] and loosen
the hand wheel (Item 2) [A].
P–09834
Raise the lift arms until the mounting couplers are away
from the mounting balls [B].
B
Disconnect the auxiliary couplers (Item 1) [B] from the
loader quick couplers.
Stop the engine, release the seat belt, and raise the seat
bar.
Move the pedals to check that both pedals lock. Engage the
parking brake.
P–09836
Release the Bob–Tach levers [C].
Enter the cab, lower the seat bar and fasten the seat belt.
Start the engine and release the parking brake. C
Place blocks on the ground and tilt the Bob–Tach forward
and lower the lift arms until the mounting frame rests on the
blocks.
Tilt the Bob–Tach forward, lower the lift arms and back the
loader from the backhoe main frame.
Stop the engine, release the seat belt, and raise the seat
bar.
Move the pedals to check that both pedals lock. Engage the
parking brake.
CD–10381
Reverse the procedure to install the backhoe mounting
frame.
Backhoe
24 of 176 –1–16– Service Manual
SWING FRAME
Removal (905B)
A
Remove the boom and arm assembly. (See Page 1–16.) 3
Installation
Use a chain hoist to position the swing frame in the bottom
D–01312
Backhoe
25 of 176 –1–17– Service Manual
SWING FRAME (Cont’d)
Removal (913, 911, 911B, 911C, 811, 607, 709, & 8709)
A
1
Remove the boom and arm assembly. (See Page 1–16.)
Position the backhoe mounting frame on the floor so the
2
swing is up. Use wooden blocks to support the frame.
3
Remove the cap (Item 1) [A], bolts (Item 2) [A], and
washers (Item 3) [A].
Support the swing frame (Item 4) [A] with the chain hoist.
5
Use a hammer and punch to remove the pivot pin (Item 5)
[A].
Remove the swing frame.
Replace worn or damaged parts as needed.
Installation
Use a chain hoist to position the swing frame (Item 4) [A]
for pivot pin installation.
Install the pivot pin (Item 5) [A], the washers (Item 3) [A],
and bolts (Item 2) [A].
2 E–02034
Backhoe
26 of 176 –1–18– Service Manual
SWING FRAME (Cont’d)
Removal (907 & 909)
A
Remove the boom and arm assembly. (See Page 1–16.) 1
Position the backhoe mounting frame on the floor so the
2
swing is up. Use wooden blocks to support the frame. 3
8
9
E–01316
Backhoe
27 of 176 –1–19– Service Manual
SWING FRAME (Cont’d)
Removal (914B)
A
Remove the boom and arm assembly. (See Page 1–16.)
1
Position the backhoe mounting frame on the floor so the 2
swing frame is up. Use wooden blocks to support the
mounting frame. 3
Remove the cap (Item 1) [A], bolts (Item 2) [A], and
washers (Item 3) [A].
Support the swing frame (Item 4) [A] with the chain hoist. 5
Use a hammer and punch to remove the pivot pin (Item 5)
[A].
Remove the swing frame (Item 4) [A].
Remove the upper bearing (Item 6) [A] and the lower
bearing (Item 7) [A].
Replace worn or damaged parts as needed.
Installation (914B)
reverse the procedure to install the swing frame.
3
2
E–01854
Backhoe
28 of 176 –1–20– Service Manual
SWING FRAME (Cont’d)
Side Shift Frame Removal
A
Remove the boom and arm assembly. (See Page 1–16.)
2
Position the backhoe mounting frame on the floor so the
side shift frame and swing frame are up. Use wooden
blocks to support the assembly.
Use a hoist for support, if needed during repair. 3
Installation 6
E–02063
Backhoe
29 of 176 –1–21– Service Manual
LOCKING MECHANISM
Removal and Installation
A 2
(607, 709, 709FDS, 8709, & 811)
Remove the mounting bolt (Item 1) [A] and nut from the
handle (Item 2) [A] on the locking mechanism. 1
MC–01631
2 5
E–02050
Backhoe
30 of 176 –1–22– Service Manual
TENSION SPRING ASSEMBLY
Disassembly
A
1
Punch
5.625 inch
(143 mm)
Do not attempt to maintain or adjust unless
you are trained and have the correct
Backhoe
31 of 176 –1–23– Service Manual
TENSION SPRING ASSEMBLY (Cont’d)
Assembly (Cont’d)
A
When the handle of valve spring compression tool is fully 3
engaged, the spring assembly (Item 1) [A] must be
compressed in the holder (Item 2) [A] until the rod (Item 3) 1 2
[A] can be installed in the pivot and the rod extends from
the tool far enough to install the clevis and roll pin.
Vise
MC–01637
MC–01631
Backhoe
32 of 176 –1–24– Service Manual
SAFETY CHAIN
Inspection and Maintenance
A
(607, 709, 709FDS, 8709, & 811)
Check the chain, clip, pins, and hitch pin wire for wear [A].
Replace any worn, damaged, or missing parts. Check the
condition of the decal (Item 1) [A] and replace if damaged
or missing.
1
Check the condition of the Bob–Tach levers and see that
the levers contact the frame where shown when locked [B].
Check the decal (Item 1) [B]. Replace if damaged or
missing.
P–10205
BackhoeService Manual #6900622 – Contents & Main Frame Section Part 1 of 2
B
1
Lever
Will
P–10185
Backhoe
33 of 176 –1–25– Service Manual
TENSION SPRING ASSEMBLY (Cont’d)
Assembly (Cont’d)
A
When the handle of valve spring compression tool is fully 3
engaged, the spring assembly (Item 1) [A] must be
compressed in the holder (Item 2) [A] until the rod (Item 3) 1 2
[A] can be installed in the pivot and the rod extends from
the tool far enough to install the clevis and roll pin.
Vise
MC–01637
Adjustment
C
Measure the distance from the center of the clevis hole to
the center of the pivot hole [C]. 7.0 inch
(178 mm)
Place the tension spring assembly in a vise (clevis end in
the vise), and use a wrench to turn the pivot in or out to
adjust the distance to 7.0 inches (178 mm) [C].
NOTE: The adjustment length [C] is the same for the
following backhoes; 607, 709, 709FDS, 8709, &
811.
MC–01631
Backhoe
34 of 176 –1–26– Service Manual
SAFETY CHAIN
Inspection and Maintenance
A
(607, 709, 709FDS, 8709, & 811)
Check the chain, clip, pins, and hitch pin wire for wear [A].
Replace any worn, damaged, or missing parts. Check the
condition of the decal (Item 1) [A] and replace if damaged
or missing.
1
P–10205
Lever
Will
P–10185
Backhoe
35 of 176 –1–27– Service Manual
SAFETY CHAIN (Cont’d)
Safety chain must be installed on the following backhoes;
A
607, 709, 709FDS, 8709, & 811. (See Service Letter dated
9, October 1997 for serial numbers effected.)
Use the reference in drawing [A] and below to locate the
position to drill one 13/32 inch (10 mm) hole in the backhoe 1
mounting frame.
NOTE: The hole location is determined by model. Use
the correct location for each model. 2
Model Model 607, 709,
Ref. 811 709FDS, 8709
1 1.5 inch (38 mm) 1.75 inch (44 mm)
2 5.0 inch (127 mm) 2.50 inch (64 mm) B–14988
Warning Decal
B–14987
Warning
Decal
B–14989
Backhoe
36 of 176 –1–28– Service Manual
SAFETY CHAIN (Cont’d)
A
Install a bolt (P/N 1C612) and nut (P/N 85D6) in the new
Backhoe
37 of 176 –1–29– Service Manual
BackhoeService Manual #6900622 – Contents & Main Frame Section Part 2 of 2
Backhoe
38 of 176 –1–30– Service Manual
HYDRAULIC CONTROL VALVE
Page
Number
CONTROL VALVE
Checking The Main Relief Valve On The Backhoe . . . . . . . . . . . . . . . 2–3
Checking The Port Relief Valve on the Backhoe . . . . . . . . . . . . . . . . . 2–4
Description (Cessna–907, 909, & 911) . . . . . . . . . . . . . . . . . . . . . . . . . 2–24
Parts Identification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2–24
Disassembly And Assembly (Not Available At Printing)
HYDRAULIC
Description (Husco–907, 909, & 911) . . . . . . . . . . . . . . . . . . . . . . . . . . 2–25 CONTROL VALVE
Parts Identification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2–25
Disassembly And Assembly (Not Available At Printing)
Description (Danfoss–Dukes–607, 709, 709FDS & 8709) . . . . . . . . . 2–6
Centering Mechanism . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2–8
Disassembly And Assembly
(Danfoss–Dukes–607, 709, 709 FDS & 8709) . . . . . . . . . . . . . . . . . 2–7
Parts Identification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2–6
Description (Danfoss–Dukes–811) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2–12
Backhoe
39 of 176 –2–1– Service Manual
Dealer Copy -- Not for Resale
Backhoe
40 of 176 –2–2– Service Manual
HYDRAULIC SYSTEM INFORMATION
41 of 176
HYDRAULIC SYSTEM INFORMATION (Cont’d)
42 of 176
HYDRAULIC SYSTEM INFORMATION (Cont’d)
43 of 176
44 of 176
Dealer Copy -- Not for Resale
45 of 176
Dealer Copy -- Not for Resale
46 of 176
Dealer Copy -- Not for Resale
47 of 176
Dealer Copy -- Not for Resale
48 of 176
Dealer Copy -- Not for Resale
49 of 176
Dealer Copy -- Not for Resale
50 of 176
Dealer Copy -- Not for Resale
51 of 176
Dealer Copy -- Not for Resale
52 of 176
Dealer Copy -- Not for Resale
53 of 176
Dealer Copy -- Not for Resale
54 of 176
Dealer Copy -- Not for Resale
55 of 176
Dealer Copy -- Not for Resale
56 of 176
Dealer Copy -- Not for Resale
57 of 176
Dealer Copy -- Not for Resale
58 of 176
Dealer Copy -- Not for Resale
59 of 176
Dealer Copy -- Not for Resale
60 of 176
Dealer Copy -- Not for Resale
CONTROL VALVE
Checking The Main Relief Valve On The Backhoe
A
NOTE: Verify that the loader hydraulic pressure and
flow meet specifications before attempting the
backhoe pressure checks.
1
NOTE: Determine if the main relief valve being
checked is adjustable.
NOTE: When using the following procedure, the main
relief valve on the backhoe must have a lower
pressure setting than the main relief valve on
the loader.
Backhoe
61 of 176 –2–3– Service Manual
CONTROL VALVE (Cont’d)
Checking The Port Relief Valve on the Backhoe
A
3
NOTE: Verify that the loader hydraulic pressure and
flow meet specifications before attempting the
backhoe pressure checks.
NOTE: Determine if the port relief valve being
checked is adjustable.
NOTE: A port–a–power and gauge will be used to 1
check the port relief valves. 4
2
P–13532
B
Hydraulic fluid escaping under pressure can
have sufficient force to enter a person’s body
by penetrating the skin. This can cause serious
injury and possibly death if proper medical
treatment by a physician familiar with this
injury is not received immediately.
W–2145–0290
Backhoe
62 of 176 –2–4– Service Manual
CONTROL VALVE (Cont’d)
Removal
A
Use the following procedure to remove the hydraulic
control valve.
Lower the bucket, arm, and boom to the ground and
support them with blocks [A].
Stop the engine. Engage the parking brake.
Move the backhoe hydraulic control levers to release the
hydraulic pressure.
Clean the area around the control valve. Mark all the
tubelines and/or hoses for correct installation. BLOCK HERE
P–13581
Installation
Use the reverse procedure to install the control valve on the
backhoe mounting panel.
NOTE: During installation, use four mounting bolts to
install the control valve on the 905B mounting
panel.
NOTE: During installation, use only three mounting
bolts to install the control valve on the
backhoe mounting panel.
Tighten the following mounting bolts to the torque shown:
Bolt Diameter Torque
.250 inch (1/4) 80 in.–lbs. (9 Nm)
.3125 inch (5/16) 180 in.–lbs. (21 Nm)
.500 inch (1/2) 65 ft.–lbs. (88 Nm)
.625 inch (5/8) 125 ft.–lbs. (170 Nm)
Backhoe
63 of 176 –2–5– Service Manual
CONTROL VALVE (Cont’d)
Description (Danfoss–Dukes – 607, 709, 709FDS &
8709)
The control valve has two sections. Each section can be
repaired individually.
All parts are replaceable in the control valve. The spool and
valve body are replaced as a unit.
The boom, arm, and swing sections have relief valves that
can be removed for repair or replacement without
disassembling the control valve. DO NOT interchange
relief valves.
Parts Identification
D E
B
F
E C
D G
D
F
B A – Valve Sections
B – Main Relief Valve
2300–2400 PSI (15856–16546 kPa)
@ 0.75 GPM (2,8 L/m)
C – Port Relief Valve
E 2800–2900 PSI (19303–19953 kPa)
@ 0.75 GPM (2,8 L/m)
D D – Anti–Cavitation/Port Relief Valve
2200–2300 PSI (15169–15856 kPa)
@ 0.75 GPM (2,8 L/m)
E – Port Relief Valve
A 3000–3100 PSI (20682–21374 kPa)
@ 0.75 GPM (2,8 L/m)
G
F – Port Relief Valve
2300–2400 PSI (15856–16546 kPa)
@ 0.75 GPM (2,8 L/m)
C
G – Plug
D–02111
Backhoe
64 of 176 –2–6– Service Manual
CONTROL VALVE (Cont’d)
Disassembly And Assembly
A 2
3 2
(Danfoss–Dukes 607, 709, 709FDS & 8709)
2
Always use new O–rings and back–up washers. Lubricate
the O–rings and back–up washers with hydraulic oil during
assembly.
Mark the relief valve locations before disassembly. 2
Mark the valve sections before disassembly.
Remove the main relief valve (Item 1) [A].
1 2
Installation: Tighten the main relief valve to 30–35 ft.–lbs.
(41–47 Nm) torque. P–13410
P–13415
1
2
1
P–13414
Remove the load checks (Item 3) [A].
Installation: Tighten the load check to 180–240 in.–lbs.
(20–27 Nm) torque.
D 3
Check the condition of the spacer (Item 1) [D] and the
spring (Item 2) [D]. Replace the O–ring (Item 3) [D].
2
Replace the spacer and spring as needed.
1
Install the spacer (Item 1) [D] with the champhered edge
toward the spring.
P–13423
Backhoe
65 of 176 –2–7– Service Manual
CONTROL VALVE (Cont’d)
Disassembly And Assembly (Cont’d)
A
(Danfoss–Dukes 607, 709, 709FDS & 8709) (Cont’d)
Remove the screws (Item 1) [A] and the centering spring
cover (Item 2) [A].
Remove the spool and centering spring assembly (Item 3)
[A]. 2
3
Installation: Tighten the screws to 24–36 in.–lbs. (3–4
Nm) torque.
1
P–13421
Centering Mechanism
CAREFULLY remove the centering spring bolt (Item 1) [B], B
there is spring pressure.
Backhoe
66 of 176 –2–8– Service Manual
CONTROL VALVE (Cont’d)
Disassembly And Assembly (Cont’d)
A
(Danfoss–Dukes 607, 709, 709FDS & 8709) (Cont’d)
Remove the O–ring (Item 1) [A] from the spool bore on the
centering spring end of the control valve section.
P–13418
Remove the wiper (Item 1) [B] from the spool bore on the
linkage end of the control valve.
B
P–13422
Remove the O–ring (Item 1) [C] from the spool bore on the
linkage end of the control valve.
C
P–13417
Backhoe
67 of 176 –2–9– Service Manual
CONTROL VALVE (Cont’d)
Disassembly And Assembly (Cont’d)
A
(Danfoss–Dukes 607, 709, 709FDS & 8709) (Cont’d)
1
Lubricate the new O–rings and wipers during installation.
Install the O–ring (Item 1) [A] in the spool bore groove at
the control linkage end of the control valve.
Install the wiper (Item 2) [A] in the spool bore groove at the
control linkage end of the control valve.
1
Lubricate the spool with hydraulic oil. Install the spool in the
control valve, linkage end first [A].
Slowly push while turning the spool through the O–ring and TS–01668
wiper [A].
Push the spool past the O–ring and wiper far enough to
install the O–ring (Item 1) [B] in the opposite groove in the B
spool bore.
1
Slowly push while turning the spool back into the spool bore
past the O–ring until the end of the spool is even with the C
machined surface of the control valve [C].
TS–01670
Refer to page 2–8 Fig. [B] for the correct assembly of the
centering mechanism. D
Installation: Apply a small amount of liquid adhesive
(LOCTITE #242) on the centering mechanism screw.
Hold the linkage end of the spool [allen wrench (Item 1) [D]
can be used] while tightening the centering mechanism
screw.
Tighten the screw to 90–100 in.–lbs. (10–11 Nm) torque. 1
N–16819
Backhoe
68 of 176 –2–10– Service Manual
CONTROL VALVE (Cont’d)
Disassembly And Assembly (Cont’d)
A 1
(Danfoss–Dukes 607, 709, 709FDS & 8709) (Cont’d)
Remove the nuts (Item 1) [A] and bolts holding the two
valve sections together.
Installation: Tighten the nuts to 20–23 ft.–lbs. (27–31 Nm)
torque.
P–13410
P–13416
1
P–13413
Backhoe
69 of 176 –2–11– Service Manual
CONTROL VALVE (Cont’d)
Description (Danfoss–Dukes – 811)
All parts are replaceable in the control valve. The spool and
valve body are replaced as a unit.
The control valve has separate sections for each function
of the backhoe. Each section can be repaired individually.
The boom, arm, and swing sections have relief valves that
can be removed for repair or replacement without
disassembling the control valve. DO NOT interchange
relief valves.
Parts Identification
D C C G F
E B
I I
A A A A A A
E C
D
A A Boom Stabs. Arm
A Swing Bucket
F D
A – Valve Sections
C
B – Main Relief Valve
2300–2400 PSI (15856–16546 kPa)
@ .75 GPM (2,8 L/m)
C – Pilot Operated Check Valves
D – Anti–Cavitation/Port Relief Valve
2200–2300 PSI (15167–15856 kPa)
@ .75 GPM (2,8 L/m)
E – Port Relief Valve
C 2300–2400 PSI (15856–16546 kPa)
A G @ .75 GPM (2,8 L/m)
F
A A F – Port Relief Valve
B 3000–3100PSI (20682–21371 kPa)
H @ .75 GPM (2,8 L/m)
C
G – Plugs
G
H – Port Relief Valve
2800–2900 PSI (19303–19993 kPa)
@ .75 GPM (2,8 L/m)
I – Orifices E–02070
Backhoe
70 of 176 –2–12– Service Manual
CONTROL VALVE (Cont’d)
Disassembly And Assembly
A 2
(Danfoss–Dukes 811)
Always use new O–rings and back–up washers. Lubricate
the O–rings and back–up washers with hydraulic oil during
assembly.
Mark the control valve sections and the relief valve
locations before disassembly.
3
NOTE: Tighten all relief valves to 25–30 ft.–lbs. (34–41
Nm) torque. 2
Remove the main relief valve (Item 1) [A].
1
P–13424
P–13415
1
2
1
P–13425
Backhoe
71 of 176 –2–13– Service Manual
CONTROL VALVE (Cont’d)
Disassembly And Assembly (Cont’d)
A 1
(Danfoss–Dukes 811) (Cont’d)
Remove the port relief valves (Item 1) [A].
P–13426
P–13428
2 1
1
P–13427
Backhoe
72 of 176 –2–14– Service Manual
CONTROL VALVE (Cont’d)
Disassembly And Assembly (Cont’d)
A
(Danfoss–Dukes 811) (Cont’d)
Remove the screws (Item 1) [A] and the centering spring
cover (Item 2) [A].
Installation: Tighten the screws to 24–36 in.–lbs. (3–4 3
Nm) torque.
2
Remove the spool and centering spring assembly (Item 3)
[A].
1
P–13429
Centering Mechanism
B
CAREFULLY remove the centering spring bolt (Item 1) [B],
there is spring pressure.
P–13431
Backhoe
73 of 176 –2–15– Service Manual
CONTROL VALVE (Cont’d)
Disassembly And Assembly (Cont’d)
A
(Danfoss–Dukes 811) (Cont’d)
Remove the O–ring (Item 1) [A] from the spool bore on the
centering spring end of the control valve section.
P–13432
Remove the wiper (Item 1) [B] from the spool bore on the
linkage end of the control valve.
B
P–13434
Remove the O–ring (Item 1) [C] from the spool bore on the
linkage end of the control valve.
C
P–13433
Backhoe
74 of 176 –2–16– Service Manual
CONTROL VALVE (Cont’d)
Disassembly And Assembly (Cont’d)
A
(Danfoss–Dukes 811) (Cont’d) 1
Lubricate the new O–rings and wipers during installation.
Install the O–ring (Item 1) [A] in the spool bore groove at
the control linkage end of the control valve.
Install the wiper (Item 2) [A] in the spool bore groove at the
control linkage end of the control valve.
2
Lubricate the spool with hydraulic oil. Install the spool in the
control valve, linkage end first [A].
Slowly push while turning the spool through the O–ring and TS–01668
wiper.
Push the spool past the O–ring and wiper far enough to
install the O–ring (Item 1) [B] in the opposite groove in the B
spool bore.
1
Slowly push while turning the spool back in the spool bore
past the O–ring until the spool end is even with the C
machined surface of the control valve [C].
TS–01670
Refer to page 2–15 Fig. [B] for the correct assembly of the
centering mechanism. D
Installation: Apply a small amount of liquid adhesive
(LOCTITE #242) on the centering mechanism screw.
Hold the linkage end of the spool [allen wrench (Item 1) [D]
can be used] while tightening the centering mechanism
screw.
Tighten the screw to 90–100 in.–lbs. (10–11 Nm) torque.
1
N–16817
Backhoe
75 of 176 –2–17– Service Manual
CONTROL VALVE (Cont’d)
Disassembly And Assembly (Cont’d)
A
(Danfoss–Dukes 811) (Cont’d)
Remove the nuts (Item 1) [A] from the three tie rods.
1
P–13433
P–13435
Backhoe
76 of 176 –2–18– Service Manual
CONTROL VALVE (Cont’d)
Description (Husco–725S, 730S, 835S, 923S, 923SA, &
928S)
All parts are replaceable in the control valve. The spool and
valve body are replaced as a unit.
The control valve has separate sections for each function
of the backhoe. Each section can be repaired individually.
The boom, arm, and bucket sections have relief valves that
can be removed for repair or replacement without
disassembling the control valve. DO NOT interchange
relief valves.
Parts Identification
D
G
A A
A
C
G E
D B
F
A A A A A A
G E H
F
Backhoe
77 of 176 –2–19– Service Manual
CONTROL VALVE (Cont’d)
Disassembly And Assembly
A 2
3
Remove the O–ring (Item 1) [B] from the main relief valve.
Remove the relief valve (Item 3) [A].
Installation: Tighten the relief valves (Item 3) [A] to 35
P–13436
P–13438
The boom cylinder orifice [D] is located in the rod end port
(Item 4) [A] of the control valve. D
P–13466
Backhoe
78 of 176 –2–20– Service Manual
CONTROL VALVE (Cont’d)
Disassembly And Assembly (Cont’d)
A
(Husco–725S, 730S, 835S, 923S, 923SA, & 928S)
(Cont’d)
Remove the bolts (Item 1) [A] and the centering spring
cover (Item 2) [A].
Installation: Tighten the bolts to 84 in.–lbs. (9,5 Nm)
3
torque. 2
Remove the spool and centering spring assembly (Item 3)
[A].
1
P–13442
Centering Mechanism B
CAREFULLY remove the centering spring bolt (Item 1) [B],
there is spring pressure.
1
Remove the wiper (Item 2) [B], washer (Item 3) [B], and
O–ring (Item 4) [B].
1
P–13439
Backhoe
79 of 176 –2–21– Service Manual
CONTROL VALVE (Cont’d)
Disassembly And Assembly (Cont’d)
A
(Husco–725S, 730S, 835S, 923S, 923SA, & 928S) 1
(Cont’d)
Lubricate the new O–rings and wipers during installation.
Install the O–ring (Item 1) [A] in the spool bore groove at
the control linkage end of the control valve.
Install the wiper (Item 2) [A] in the spool bore groove at the
control linkage end of the control valve. 2
Lubricate the spool with hydraulic oil. Install the spool in the
control valve, linkage end first [A].
TS–01663
Slowly push while turning the spool through the O–ring and
wiper.
Push the spool past the O–ring and wiper far enough to B
install the O–ring (Item 1) [B] and wiper (Item 2) [B] in the
opposite grooves in the spool bore. 1
TS–01664
Slowly push while turning the spool back in the spool bore
past the O–ring and wiper until the spool end is even with C
the machined surface of the control valve [C].
TS–01665
Refer to page 2–21 Fig. [B] for the correct assembly of the
centering mechanism. D
Installation: Apply a small amount of liquid adhesive
(LOCTITE #242) on the centering mechanism screw.
Hold the linkage end of the spool [allen wrench (Item 1) [D]
can be used] while tightening the centering mechanism
screw.
Tighten the screw to 84 in.–lbs. (9.5 Nm) torque.
N–16818
Backhoe
80 of 176 –2–22– Service Manual
CONTROL VALVE (Cont’d)
Disassembly And Assembly (Cont’d)
A
(Husco–725S, 730S, 835S, 923S, 923SA, & 928S)
(Cont’d)
Remove the nuts (Item 1 & 2) [A] from the three tie rods.
1
2
P–13441
Remove the end cap (Item 1) [B] and the O–ring (Item 2)
[B].
B
Remove the spring (Item 3) [B] and poppet (Item 4) [B].
Check the condition of the spring and poppet, replace if 1
needed.
3 4
P–13443
Backhoe
81 of 176 –2–23– Service Manual
CONTROL VALVE (Cont’d)
Description (Cessna–907 (S/N 1425 & Below), 909 (S/N 2030 & Below), & 911 (S/N 361 & Below)
All parts are replaceable in the control valve. The spool and valve body are replaced as a unit.
The control valve has separate sections for each function of the backhoe. Each section can be repaired individually.
The boom, arm, and bucket sections have relief valves that can be removed for repair or replacement without disassembling
the control valve. DO NOT interchange relief valves.
Parts Identification
E
D
1 A A
C A
D
E B
C
A A A A A A
D
C
A – Valve Sections B
C
B – Main Relief Valve
2100–2200 PSI (14479–15169 kPa)
@ 15 GPM (57 L/m)
C – Port Relief Valve
Cessna: 907–1425 & Below A
909–2036 & Below A
911–361 & Below A
2750 PSI (18961 kPa)
@ 0.5 GPM (1,9 L/m)
D – Plugs
D
E – Port Relief/Anticavitation Valve
Cessna: 907–1425 & Below
909–2036 & Below
911–361 & Below
3000 PSI (20682 kPa)
@ 0.5 GPM (1,9 L/m)
Tighten the three tie rod nuts (Item 1) to 20–25
ft.–lbs. (27–34 Nm) torque.
Tighten the relief valves to 27–30 ft.–lbs. (36–40
Nm) torque.
E–01622
Backhoe
82 of 176 –2–24– Service Manual
CONTROL VALVE (Cont’d)
Description (Husco–907 (S/N 1426 & Above), 909 (S/N 2037 & Above, & 911 (S/N 362 & Above)
All parts are replaceable in the control valve. The spool and valve body are replaced as a unit.
The control valve has separate sections for each function of the backhoe. Each section can be repaired individually.
The boom, arm, and bucket sections have relief valves that can be removed for repair or replacement without disassembling
the control valve. DO NOT interchange relief valves.
Parts Identification
2 D
1
C A A
A
D B
E
A A A A A A
Backhoe
83 of 176 –2–25– Service Manual
CONTROL VALVE (Cont’d)
Description (Gresen – 911C & 913)
All parts are replaceable in the control valve. The spool and
valve body are replaced as a unit.
The control valve has separate sections for each function
of the backhoe. Each section can be repaired individually.
The boom, arm, bucket, and swing sections have relief
valves that can be removed for repair or replacement
without disassembling the control valve. DO NOT
interchange relief valves.
Parts Identification
A A A A A A
C C B B
D
D
A
A
A 1
B
B
B–15146
Backhoe
84 of 176 –2–26– Service Manual
CONTROL VALVE (Cont’d)
Description (Gresen – 911B & 914B)
All parts are replaceable in the control valve. The spool and
valve body are replaced as a unit.
The control valve has separate sections for each function
of the backhoe. Each section can be repaired individually.
The boom, arm, and swing sections have relief valves that
can be removed for repair or replacement without
disassembling the control valve. DO NOT interchange
relief valves.
Parts Identification
G
E G
A
A A 1
D B
B–15145
Backhoe
85 of 176 –2–27– Service Manual
CONTROL VALVE (Cont’d)
Description (Eaton–905)
All parts are replaceable in the control valve. The spool and
valve body are replaced as a unit.
Parts Identification
B–09303
Backhoe
86 of 176 –2–28– Service Manual
CONTROL VALVE (Cont’d)
Disassembly And Assembly
A
(Eaton–905)
Always use new O–rings.
Lubricate the O–rings with hydraulic oil during assembly.
Loosen the main relief valve cap (Item 1) [A].
1
P–13446
Remove the cap (Item 1) [B], the shim (Item 2) [B], the
spring (Item 3) [B], and the poppet (Item 4) [B]. B
NOTE: The seat is threaded into the valve body with
LOCTITE. Do not remove the seat.
Installation: Tighten the cap (Item 1) [B] to 20–24 ft.–lbs.
(27–33 Nm) torque.
Remove the plug (Item 1) [C], the spring (Item 2) [C], and
the plunger (Item 3) [C]. C
Check the condition of the spring and plunger. Replace as
needed.
Installation: Tighten the plug (Item 1) [B] to 180 in.–lbs.
(20 Nm) torque.
3
2
1
P–13450
Backhoe
87 of 176 –2–29– Service Manual
CONTROL VALVE (Cont’d)
Disassembly And Assembly (Cont’d)
A
(Eaton–905) (Cont’d)
Remove the centering spring cap (Item 1) [A].
Installation: Tighten the cap to 20–25 ft.–lbs. ( 27–34 Nm)
torque.
P–13451
Centering Mechanism
Use a plier to CAREFULLY compress the centering spring B
(Item 1) [B] and remove the snap ring (Item 2) [B].
Remove the centering spring assembly.
Remove the O–ring (Item 3) [B].
1
P–13452
Remove the O–ring (Item 1) [C] from the spool bore on the
linkage end of the control valve. C
P–13447
Backhoe
88 of 176 –2–30– Service Manual
CONTROL VALVE (Cont’d)
Disassembly And Assembly (Cont’d)
A
(Eaton–905) (Cont’d)
5
Using the following procedure, assemble the centering
mechanism on the spool before installing it in the control
valve.
4
Lubricate the new O–rings during installation.
Clamp the linkage end of the spool in a vise [A]. 3
2
Install the O–ring (Item 1) [A] and the O–ring retainer (Item 1
2) [A] on the centering spring end of the spool.
Install the washer (Item 3) [A], the spring (Item 4) [A], and
the spring bushing (Item 5) [A].
P–13646
Backhoe
89 of 176 –2–31– Service Manual
CONTROL VALVE (Cont’d)
Disassembly And Assembly (Cont’d)
A 2
1
(Eaton–905) (Cont’d)
There are restrictors for the boom and swing circuits
located in ports (Item 1 & 2) [A] on the control valve.
P–13446
The restrictor [B] fits into the boom cylinder port (Item 1)
[A] with the legs up.
B
The restrictor [C] fits into the swing cylinder port (Item 2)
[A] with the crown up.
C
BackhoeService Manual #6900622 – Hydraulic Control Valve Section Part 2 of 2
P–13445
Backhoe
90 of 176 –2–32– Service Manual
HYDRAULIC CYLINDERS
Page
Number
HYDRAULIC CYLINDERS
905B Backhoe Cylinders . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3–3
923S & 923SA Backhoe Cylinders . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3–4
928S Backhoe Cylinders . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3–6
907 Backhoe Cylinders . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3–7
909 Backhoe Cylinders . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3–8
911 Backhoe Cylinders . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3–9 HYDRAULIC
730S Backhoe Cylinders . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3–10 CYLINDERS
725S Backhoe Cylinders . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3–11
835S Backhoe Cylinders . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3–13
607 Backhoe Cylinders . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3–15
709 Backhoe Cylinders . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3–17
811 Backhoe Cylinders . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3–18
8709 Backhoe Cylinders . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3–20
911C Backhoe Cylinders . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3–21
911B Backhoe Cylinders . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3–23
913 Backhoe Cylinders . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3–25
914B Backhoe Cylinders . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3–26
Backhoe
91 of 176 –3–1– Service Manual
Dealer Copy -- Not for Resale
Backhoe
92 of 176 –3–2– Service Manual
HYDRAULIC CYLINDERS
Removing Air From The Swing Cylinder
A 1
2
Swing Cylinder
Backhoe
93 of 176 –3–3– Service Manual
HYDRAULIC CYLINDERS (Cont’d) 4 Arm & Bucket
923S & 923SA Backhoe Cylinders
A Cylinder
C–02660
10
C–02686
C–03101
Backhoe
94 of 176 –3–4– Service Manual
HYDRAULIC CYLINDERS (Cont’d) Arm Cylinder 14
923S & 923SA Backhoe Cylinders (Cont’d)
A 13
Backhoe
95 of 176 –3–5– Service Manual
HYDRAULIC CYLINDERS (Cont’d) Arm & Boom
928S Backhoe Cylinders
A Cylinder
5 3
6
Arm & Boom Cylinder [A]:
9 8 7
1
1. Housing 7. O–ring
2. Nut 8. Back–Up Ring 2
3. Slipper Ring 9. Head 4
4. O–ring 10. Rod 7 3
5. Piston 11. Wiper 11
6. Sleeve 12. Seal
10
12
D–01583
Bucket Cylinder
Bucket Cylinder [B]: B
1. Housing 7. Back–Up Ring
2. Nut 8. Head
3. Piston 9. Seal 1
4. Slipper Ring 10. Wiper
5. O–ring 11. Rod
6. O–ring 6 3 2
8 7
6 4
D–01579
Swing Cylinder [C]:
1. Housing 8. O–ring Swing Cylinder
2. Nut 9. Head C 11 12
3. Piston 10. Seal 13
4. Seal 11. Wiper
5. O–ring 12. Rod
6. O–ring 13. Bearing
7. Back–Up Washer 10
6 7 8 9
Date
1 Code 2 3 4 5
C–03101
Backhoe
96 of 176 –3–6– Service Manual
HYDRAULIC CYLINDERS (Cont’d) Swing Cylinder
907 Backhoe Cylinders
A
Swing Cylinder [A]: 1
3 8
1. End Housing 5. Relief Valve 43
2. O–ring 6. O–ring 6 5 1
3. Back–Up Washer 7. Relief Valve
4. Dust Seal 8. Piston Assembly
24
2
6
7
B–13712
10
C–02686
11 8 76
10 9
C–02660
Backhoe
97 of 176 –3–7– Service Manual
HYDRAULIC CYLINDERS (Cont’d) Swing Cylinder
909 Backhoe Cylinders
A
8 6 4 2
Swing Cylinder [A]: 1
1. Piston 7. Head 2 4 6 8
2. Relief Valve 8. Ball
3. O–ring 9. Housing 7 5 3
4. Pin 10. Seal
5. Back–Up Washer 11. Wiper 3
5 7
6. O–ring 9
9 10 11
11 10 C–02592
12
D–01583
6 4
D–01579
Stabilizer Cylinder [D]:
Stabilizer Cylinder 6
1. Housing 8. Back–Up Washer D
2. Back–Up Washer 9. O–ring 4
3. O–ring 10. Rod
4. Outer Barrel 11. Head 2 898
5. Nut 12. O–ring 5 7
6. O–ring 13. Seal 1
7. Piston 14. Wiper
12
NOTE: See Page 3–28 for Hydraulic Cylinder Repair. 3
See Parts Microfiche for Repair Kits for you 3
Model backhoe cylinders.
10 14
13
11
2
C–01203
Backhoe
98 of 176 –3–8– Service Manual
HYDRAULIC CYLINDERS (Cont’d) Swing Cylinder
911 Backhoe Cylinders
A
12 12
Swing Cylinder [A]: 9 87 5 3
1 7
1. Housing 7. Back–Up Washer 2 4 8 10 13
2. Nut 8. Head 12
3. Seal 9. Seal 13 10
6 4 2
4. O–ring 10. Wiper
5. Piston 11. Cap 3 56 9
11
6. O–ring 12. Rod
14 16
15 16 14 15
15
D–01570
D–01594
6 4
D–01579
D–01765
Backhoe
99 of 176 –3–9– Service Manual
HYDRAULIC CYLINDERS (Cont’d) Arm & Boom
A Cylinder
730S Backhoe Cylinders 12
Arm & Boom Cylinder [A]: 11 10
5
1. Rod 7. Piston Ring 9
2. Wiper 8. Piston 7 5 8
3. Seal 9. Bolt
4. Head 10. Housing
5. O–ring 11. Plug
6. Back–Up Washer 12. Tube
1
5
4 5 6
2 3 C–03347
Stabilizer Cylinder 10
Stabilizer Cylinder [C]:
C
6
1. Rod 8. Piston 11
2. Wiper 9. Nut 5
3. Seal 10. Housing
4. Head 11. Tube 13
5. Back–Up Washer 12. Plug 12 4
6. O–ring 13. O–ring 3
7. Seal 8
7 2
6
9
1
C–03388
Backhoe
100 of 176 –3–10– Service Manual
HYDRAULIC CYLINDERS (Cont’d) Arm Cylinder
A 13
725S Backhoe Cylinders
Arm Cylinder [A]:
1. Rod 8. Seal 12
2. Wiper 9. O–ring 11
9 10
3. Seal 10. Piston
5 6 7 8
4. Head 11. Bolt 3 4
5. O–ring 12. Housing 2
6. Back–Up Washer 13. Tube 1
7. O–ring
C–03228
C–03236
9 1
10
2
11
3
4
5 B–14190
Backhoe
101 of 176 –3–11– Service Manual
HYDRAULIC CYLINDERS (Cont’d) Stabilizer Cylinder
725S Backhoe Cylinders (Cont’d)
A
6
11
Stabilizer Cylinder [A]: 5
1. Rod 8. Piston 13
2. Wiper 9. Nut 12 4
3. Seal 10. Housing 3
4. Head 11. Tube 8
5. Back–Up Washer 12. Plug 7 2
6. O–ring 13. O–ring 6
7. Seal 9
NOTE: See Page 3–28 for Hydraulic Cylinder Repair. 1
See Parts Microfiche for Repair Kits for you
Model backhoe cylinders. C–03388
Backhoe
102 of 176 –3–12– Service Manual
HYDRAULIC CYLINDERS (Cont’d) Arm & Boom15 14
835S Backhoe Cylinders
A Cylinder 13
12
Arm & Boom Cylinder [A]:
11
10
1. Rod 9. O–ring 9
2. Wiper 10. Piston 8
3. Seal 11. Bolt 6 7
5
4. Head 12. Housing 4
5. O–ring 13. O–ring 3
6. Back–Up Washer 14. Plug 2
7. O–ring 15. Tube 1
8. Seal
C–03247
C–03101
Backhoe
103 of 176 –3–13– Service Manual
HYDRAULIC CYLINDERS (Cont’d) Stabilizer 14
835S Backhoe Cylinders (Cont’d)
A Cylinder 13
Backhoe
104 of 176 –3–14– Service Manual
HYDRAULIC CYLINDERS (Cont’d) Swing Cylinder
607 Backhoe Cylinders
A
Swing Cylinder [A]:
12 9 7 5 3
1. Housing 8. O–ring 2 4 6 8 10 12
2. Nut 9. Head
3. O–ring 10. Seal 13 10 8 6
4. Seal 11. Wiper 4 2
1 3 5 7 9 11
5. Piston 12. Cap
6. O–ring 13. Rod
7. Back–Up Washer
13
13
D–02085
C–03236
C–03388
Backhoe
105 of 176 –3–15– Service Manual
HYDRAULIC CYLINDERS (Cont’d) Arm Cylinder
607 Backhoe Cylinders (Cont’d)
A 15
14
Arm Cylinder [A]: 13
1. Rod 9. O–ring
2. Wiper 10. Piston 10
3. Seal 11. Bolt 6 8
4. Head 12. Housing 5 12
5. O–ring 13. O–ring 3
6. Back–Up Washer 14. Plug 11
7. O–ring 15. Tube 1 9
8. Seal 7
NOTE: See Page 3–28 for Hydraulic Cylinder Repair. 4
See Parts Microfiche for Repair Kits for you 2
B–14390
Model backhoe cylinders.
Backhoe
106 of 176 –3–16– Service Manual
HYDRAULIC CYLINDERS (Cont’d) Swing Cylinder
709 Backhoe Cylinders
A
Swing Cylinder [A]:
11 9 7 5 3
1. Housing 8. O–ring 2 4 6 8 10 12
2. Nut 9. Head
3. O–ring 10. Seal 12 10 8 6
4. Seal 11. Wiper 4 2
1 3 5 7 9 11
5. Piston 12. Cap
6. O–ring 13. Rod
7. Back–Up Washer
13
13
D–02085
C–03228
C–03236
C–03388
Backhoe
107 of 176 –3–17– Service Manual
HYDRAULIC CYLINDERS (Cont’d) Swing Cylinder
A
811 Backhoe Cylinders
Swing Cylinder [A]: 11 9
6 6 4 2 1
1. Housing 7. Back–Up Washer 2 4 6 6
2. Bolt 8. Head 9 11
3. O–ring 9. Seal 10 8 7
4. Seal 10. Wiper 5 3
5. Piston 11. Cap 3 5 7 8 10
6. O–ring 12. Rod
12
12
D–02116
C–03247
C–03236
Stabilizer Cylinder [D]:
1.
2.
Rod
Wiper
9.
10.
Piston
Bolt
D 14 12
13
3. Seal 11. O–ring Stabilizer Cylinder
4. Head 12. Plug 15
5. O–ring 13. Housing 8
6. Back–Up Washer 14. Elbow 6 11
7. O–ring 15. Tube
8. Piston Seal 4 10
2 7 9
7
1 5
3
C–03320
Backhoe
108 of 176 –3–18– Service Manual
HYDRAULIC CYLINDERS (Cont’d)
811 Backhoe Cylinders (Cont’d)
A Stabilizer Cylinder
15 14
Backhoe
109 of 176 –3–19– Service Manual
HYDRAULIC CYLINDERS (Cont’d) Swing Cylinder
8709 Backhoe Cylinders
A
Swing Cylinder [A]:
11 9 7 5 3
1. Housing 8. O–ring 2 4 6 8 10 12
2. Nut 9. Head
3. Seal 10. Seal 12 10 8 6
4. O–ring 11. Wiper 4 2
1 3 5 7 9 11
5. Piston 12. Cap
6. O–ring 13. Rod
7. Back–Up Washer
13
13
D–02085
C–03236
C–03381
Backhoe
110 of 176 –3–20– Service Manual
HYDRAULIC CYLINDERS (Cont’d) Boom & Arm 14
A Cylinder 15 13
911C Backhoe Cylinders
12
Arm & Boom Cylinder [A]:
11
10
1. Rod 9. O–ring 9
2. Wiper 10. Piston 8
3. Seal 11. Bolt 6 7
5
4. Head 12. Housing 4
5. O–ring 13. O–ring 3
2
6. Back–Up Washer 14. Plug
7. O–ring 15. Tube 1
8. Seal
C–03247
12
D–01713
C–03253
Backhoe
111 of 176 –3–21– Service Manual
HYDRAULIC CYLINDERS (Cont’d) Lock Cylinder
911C Backhoe Cylinders
A 10 12
11
Lock Cylinder [A]: 8 9
6 7
1. Rod 7. O–ring 4 5
2. Wiper 8. Slipper Ring
3. Seal 9. Sleeve 2 3
4. Head 10. Piston
5. Back–Up Washer 11. Nut
6. O–ring 12. Housing 1
NOTE: See Page 3–28 for Hydraulic Cylinder Repair.
See Parts Microfiche for Repair Kits for you
Model backhoe cylinders.
C–02895
Backhoe
112 of 176 –3–22– Service Manual
HYDRAULIC CYLINDERS (Cont’d) Swing Cylinder
911B Backhoe Cylinders
A
Swing Cylinder [A]: 1110 8
6 4 2
1. Housing 7. Back–Up Washer 1
2 4 6
2. Nut 8. Head 8 1011
3. Seal 9. Seal 9
4. O–ring 10. Wiper 7 5 3
5. Piston 11. Cap 3
6. O–ring 12. Rod 5 7 9
12
12
D–01713
D–01594
7 9
D–01579
Stabilizer Cylinder [D]:
Stabilizer Cylinder
1. Rod 8. Seal D
2. Wiper 9. Piston
14
3. Seal 10. Nut
4. Head 11. Housing 12
5. O–ring 12. O–ring 13
6. Back–Up Washer 13. Plug 8
6
7. O–ring 14. Tube 4
2 3
1 11
9 10
5 7
D–01765
Backhoe
113 of 176 –3–23– Service Manual
HYDRAULIC CYLINDERS (Cont’d) 7
911B Backhoe Cylinders (Cont’d)
A Tilt Cylinder 6
5
Tilt Cylinder [A]: 4
1. Plug 7. O–ring 3
2. O–ring 8. O–ring
3. Housing 9. Back–Up Washer 1 13
4. Nut 10. Head 2
5. Piston 11. Seal
6. Ring 12. Wiper 12
13. Rod 11
10
8
8 9 B–14043
C–02895
Backhoe
114 of 176 –3–24– Service Manual
HYDRAULIC CYLINDERS (Cont’d) Swing Cylinder
913 Backhoe Cylinders
A
Swing Cylinder [A]: 1110 8
6 4 2
1
1. Housing 7. Back–Up Washer 2 4 6
2. Nut 8. Head 8 1011
3. Seal 9. Seal 9 7 5 3
4. O–ring 10. Wiper
5. Piston 11. Cap 3 5 9
7
6. O–ring 12. Rod
12
12
D–01713
C–02891
C–02892
C–02890
Backhoe
115 of 176 –3–25– Service Manual
HYDRAULIC CYLINDERS (Cont’d) Swing Cylinder
914B Backhoe Cylinders
A
Swing Cylinder [A]: 1110 8
6 4 2
1
1. Housing 7. Back–Up Washer 2 4 6
2. Nut 8. Head 8 1011
3. Seal 9. Seal 9 7 5 3
4. O–ring 10. Wiper
5. Piston 11. Cap 3 5 9
7
6. O–ring 12. Rod
12
12
D–01713
C–02895
C–02890
Backhoe
116 of 176 –3–26– Service Manual
HYDRAULIC CYLINDERS (Cont’d) Arm & Boom
A Cylinder
16 18
914B Backhoe Cylinders (Cont’d)
Arm & Boom Cylinder [A]: 17
15 14
1. Rod 10. Seal 14
6
2. Wiper 11. Washer 4 5
3. Seal 12. Bolt 2 10
4. Head 13. Housing 1
5. Back–Up Washer 14. O–ring 13
6. O–ring 15. Plug
7. Spacer (Arm) 16. Tube 3
8. Piston 17. Elbow 11 12
9. O–ring 18. Nut 9
7 8
D–03043
C–02892
15
16 17
22 18 20
19
21
23
B–12456
Backhoe
117 of 176 –3–27– Service Manual
HYDRAULIC CYLINDER (Cont’d)
Use the following tools to disassemble and assemble the
A
hydraulic cylinder:
MEL1074 O–Ring Seal Hook
MEL1396 Seal Installation Tool
MEL1032 or MEL1033 Rod Seal Installation Tool
MEL1075 Adjustable Gland Nut Wrench
MEL1076 Cylinder Wrench
MEL1526 Torque Multiplier
Disassembly
NOTE: The drawings may not show the cylinder
exactly as it appears, but the procedure is
similar for all the cylinders. B–07000
Put the base end of the hydraulic cylinder in a drain pan.
Move the rod slowly in and out to remove the fluid from the
cylinder and into the drain pan. B
Put the base end of the cylinder in a vise.
Use a adjustable gland nut wrench to loosen the head [A].
Remove the rod assembly from the cylinder case [B].
Remove the cylinder case from the vise
B–07001
Remove the nut from the piston end of the rod [C]. C
B–07002
Pull the piston (Item 1) [D] off the rod. If the cylinder has a
cushion sleeve (Item 2) [D], pull it off the rod. Pull the head
D
(Item 3) [D] off the rod.
3
2
B–07003
Backhoe
118 of 176 –3–28– Service Manual
HYDRAULIC CYLINDER (Cont’d)
Disassembly (Cont’d)
A
If the head has a seal, remove the seal from the head [A].
B–07004
B–07005
B–07006
Backhoe
119 of 176 –3–29– Service Manual
HYDRAULIC CYLINDER (Cont’d)
Disassembly (Cont’d)
A
Remove the piston seal from the piston [A].
B–03639
Remove the O–ring from the piston [B]. Wash the cylinder
parts in clean solvent and air dry them. B
NOTE: While servicing the cylinder do not damage
the parts. Inspect for nicks, scratches or
otherwise damaged or bent parts before
assembling the cylinder. Replace parts that
appear damaged in any way. The cylinder may
not function correctly if there is damage to any
of the parts.
Assembly
Always use new o–rings and seals during assembly.
C
Install the O–ring on the piston [C].
NOTE: Do not overstretch the seal.
B–12812
Install the seal on the tool and stretch it until it fits the piston
[D]. D
Allow the O–ring to stretch for 30 seconds before removing
it from the tool.
B–12809
Backhoe
120 of 176 –3–30– Service Manual
HYDRAULIC CYLINDER (Cont’d)
Assembly (Cont’d)
A
Install the seal on the piston [A].
B–12813
B–03702
B–03671
Backhoe
121 of 176 –3–31– Service Manual
HYDRAULIC CYLINDER (Cont’d)
Assembly (Cont’d)
A
Install the wiper seal with the lip toward the outside of the
head [A].
B–03682
B–07200
B–07007
Backhoe
122 of 176 –3–32– Service Manual
HYDRAULIC CYLINDER (Cont’d)
Assembly (Cont’d)
A
If a seal was removed from the head, use the following
procedure to install a new seal.
Install the guide with a pilot and an adapter, on the head (if
needed) [A].
Install the seal on the head using the guide [A].
NOTE: Do not turn (roll) the seal as you install it.
Damage to the seal may result.
B–07009
B–07011
B–07198
Backhoe
123 of 176 –3–33– Service Manual
HYDRAULIC CYLINDER (Cont’d)
Assembly (Cont’d)
A
Install the stop (if so equipped) and piston on the rod [A].
B–03853
B–07013
B–07012
Backhoe
124 of 176 –3–34– Service Manual
HYDRAULIC CYLINDER (Cont’d)
Assembly (Cont’d)
A
Install the rod assembly in the cylinder case [A].
B–07001
Put oil on the seals and on the threads of the head [B].
B
B–07000
Replace the seal on the rod end (If so equipped) if it shows
signs of wear or damage [D].
D
B–07015
Backhoe
125 of 176 –3–35– Service Manual
HYDRAULIC CYLINDER (Cont’d)
914B Extendable Cylinder Disassembly
A
Spanner
Wrench
Drain the hydraulic oil from the cylinder.
Use soft jaws in a vise when holding the cylinder.
Remove the set screw that secures the head.
Use a spanner wrench to remove the head [A].
CD–15293
Put the rod end in the vise and remove the housing [B].
NOTE: A slight tap on the housing may be needed to B
free the head.
Check the bearing on the rod for excessive play. the
bearing inside diameter should be no more than .008 inch
(0,203 mm) larger then the rod diameter. Replace bearing
if worn. Replace the piston if worn.
CD–15294
Remove the roll pin and nut from the rod [C].
Remove the piston, cushion, and head.
C Disassembly: Assembly:
Install
Remove
Roll Pin New
Remove all seals from the piston, head and rod [C]. First Roll Pin
Wash all parts with cleaning solvent and air dry.
CD–15296
Backhoe
126 of 176 –3–36– Service Manual
HYDRAULIC CYLINDER (Cont’d)
914B Extendable Cylinder Assembly
A
Install
Install O–rings, seals, and all other parts in the reverse Cushion
order. First
Coat
Inside
CD–15297
Use
Protectors
When
Cylinder
Is In
Vise CD–15298
CAUTION
Assembly
When installing the cylinder assembly into the Install
extension, be sure that the return line tube is on Lock
the bottom, i.e., toward the ground. If the Screw
cylinder is installed upside down, it will be
damaged during operation.
C–0004–1097
CD–15299
Backhoe
127 of 176 –3–37– Service Manual
PISTON NUT TORQUE PROCEDURE
Always clean and dry the threads on the cylinder rod. Do
not oil the threads. Apply LOCTITE 242 adhesive on the
threads. Apply a thin amount of grease to both sides of the
piston, where the nut and rod will make contact, before
tightening the nut.
When servicing an older cylinder that uses a pre–torque nut
(example 86D–18), clean the threads and use red Loctite,
number 262 thread locker.
Tighten the nut to the torque shown in the chart below.
Aluminum
92D10 0.625 15/16 1.000/1.250 Iron/Steel 90 122
Aluminum
92D12 0.750 1–1/8 1.000 Iron/Steel 105 142
Aluminum
92D12 0.750 1–1/8 1.250/1.500 Iron/Steel 180 244
92D14 0.875 1–5/16 1.250 Iron/Steel 300 407
92D14 0.875 1–5/16 1.375 Aluminum 250 339
1.375/1.500
P–10450 P–10456
Backhoe
128 of 176 –3–38– Service Manual
SPECIFICATIONS
Page
Number
BACKHOE SPECIFICATIONS
905B (440, 443, 453) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4–3
905B (540, 543, 553) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4–5
907 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4–7
909 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4–9
911 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4–11
913 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4–13
607 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4–15
709 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4–17
8709 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4–19
811 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4–21
911B . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4–23
914B . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4–25 SPECIFICATIONS
914B Extendable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4–27
725S . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4–29
730S (730 & 740 Series) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4–31
730S (753L, 763, 7753, & 773) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4–33
923S . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4–35
BUCKET SPECIFICATIONS
905B . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4–46
907 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4–46
909 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4–46
911 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4–45
913 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4–45
607 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4–47
709 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4–47
8709 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4–47
811 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4–47
Backhoe
129 of 176 –4–1– Service Manual
Dealer Copy -- Not for Resale
Backhoe
130 of 176 –4–2– Service Manual
BACKHOE SPECIFICATIONS 905B • Dimensions are given for loader equipped with standard tires and dirt bucket.
Dimensions may vary with other types. All dimensions are shown in inches. Respective
metric dimensions are given in millimeters enclosed by parentheses.
• Where applicable, specifications conform to SAE or ISO standards and are subject to
change without notice.
A E
48.00
(1219)
72.00
(1829) C–02811
36.00 12.00 0 24.00 48.00 72.00 96.00
(914) (305) (610) (1219) (1829) (2438)
84
(2134)
90°
90°
84
(2134) B–06608
Backhoe
131 of 176 –4–3– Service Manual
BACKHOE SPECIFICATIONS 905B (Cont’d)
440, 443, 453
HYDRAULIC SPECIFICATIONS
Operating Hydraulic Pressure (Loader) . . . . . 1350 PSI (9308 kPa)
Relief Valve Setting (Backhoe) . . . . . . . . . . . . 1000 PSI (6895 kPA)
Pump Capacity . . . . . . . . . . . . . . . . . . . . . . . . . . 6.8 GPM (25,7 L/min) @ 3200 RPM
Digging Force Using Bucket Cylinder . . . . . . . 2064 lbs. (937 kg)
Digging Force Using Arm Cylinder . . . . . . . . . 605 lbs. (275 kg)
Hydraulic Lift Capacity – Boom . . . . . . . . . . . . 450 lbs. (204 kg)
– Arm . . . . . . . . . . . . . 690 lbs. (313 kg)
Cylinders . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Doubleacting
TRANSPORT
A Transport Height . . . . . . . . . . . . . . . . . . . . . . 71.85 (1825)
Stabilizer Spread (Transport) . . . . . . . . . . . 52.00 (1321)
OPERATIONAL
C Digging Depth Maximum . . . . . . . . . . . . . . . 69.00 (1753)
D Digging Depth 2 ft. (0,6 m) Flat Bottom . . 66.00 (1676)
E Overall Operating Height Fully Raised . . . 72.00 (1829)
F Loading Height Standard Bucket . . . . . . . . 43.00 (1092)
G Loading Reach Standard Bucket . . . . . . . . 39.00 (991)
H Reach from Swing Pivot . . . . . . . . . . . . . . . 84.00 (2134)
Reach from CL to Front Axle . . . . . . . . . . . 108.31 (2751)
Controls:
Boom, Arm, Bucket & Swing . . . . . . . . . . . . Two Hand Levers
Stabilizer . . . . . . . . . . . . . . . . . . . . . . . . . . . . Mechanical Adjustment
WEIGHT
Weight Distribution:
Weight Front . . . . . . . . . . . . . . . . . . . . . . . . . 1630 lbs (740 kg)
Rear . . . . . . . . . . . . . . . . . . . . . . . . . . 1120 lbs (508 kg)
Operating Weight . . . . . . . . . . . . . . . . . . . . . 2750 lbs (1249 kg)
Shipping Weight . . . . . . . . . . . . . . . . . . . . . . 550 lbs (250 kg)
Backhoe
132 of 176 –4–4– Service Manual
BACKHOE SPECIFICATIONS 905B (Cont’d) • Dimensions are given for loader equipped with standard tires and dirt bucket.
Dimensions may vary with other types. All dimensions are shown in inches. Respective
metric dimensions are given in millimeters enclosed by parentheses.
• Where applicable, specifications conform to SAE or ISO standards and are subject to
change without notice.
B
G
E
A
F
24.00
72.00
(1829)
0
36.00 12.00 24.00 48.00 72.00 96.00
(914) (305) (610) (1219) (1829) (2438)
C–02608
84
(2134)
90°
90°
84
(2134)
D–01408
Backhoe
133 of 176 –4–5– Service Manual
BACKHOE SPECIFICATIONS 905B (Cont’d)
540, 543, 553
HYDRAULIC SPECIFICATIONS
Operating Hydraulic Pressure (Loader) . . . . . 1575 PSI (10860 kPa)
Relief Valve Setting (Backhoe) . . . . . . . . . . . . 1000 PSI (6895 kPa)
Pump Capacity . . . . . . . . . . . . . . . . . . . . . . . . . . 8.50 GPM (32,2 L/min.) @ 3200 RPM (540)
8.00 GPM (30,3 L/min.) @ 3000 RPM (543)
Digging Force Using Bucket Cylinder . . . . . . . 2064 lbs. (937 kg)
Digging Force Using Arm Cylinder . . . . . . . . . 605 lbs. (275 kg)
Hydraulic Lift Capacity – Boom . . . . . . . . . . . . 470 lbs. (214 kg)
– Arm . . . . . . . . . . . . . 740 lbs. (336 kg)
Cylinders . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Doubleacting
TRANSPORT
A Transport Height . . . . . . . . . . . . . . . . . . . . . . 69.25 (1759)
OPERATIONAL
C Digging Depth Maximum . . . . . . . . . . . . . . . 69.00 (1753)
D Digging Depth 2 ft. (0,6 m) Flat Bottom . . 66.00 (1676)
E Overall Operating Height Fully Raised . . . 72.00 (1829)
F Loading Height Standard Bucket . . . . . . . . 43.00 (1092)
G Loading Reach Standard Bucket . . . . . . . . 39.00 (991)
H Reach from Swing Pivot . . . . . . . . . . . . . . . 84.00 (2134)
Reach from CL to Front Axle . . . . . . . . . . . 112.0 (2845)
Controls:
Boom, Arm, Bucket & Swing . . . . . . . . . . . . Two Hand Levers
Stabilizer . . . . . . . . . . . . . . . . . . . . . . . . . . . . Mechanical Adjustment
WEIGHT
Weight Distribution:
Weight Front . . . . . . . . . . . . . . . . . . . . . . . . . 1790 lbs. (813 kg)
Rear . . . . . . . . . . . . . . . . . . . . . . . . . 1860 lbs. (844 kg)
Operating Weight . . . . . . . . . . . . . . . . . . . . . . . . 3650 lbs. (1657 kg)
Shipping Weight . . . . . . . . . . . . . . . . . . . . . . . . . 550 lbs. (250 kg)
Backhoe
134 of 176 –4–6– Service Manual
BACKHOE SPECIFICATIONS 907 • Dimensions are given for loader equipped with standard tires and dirt bucket.
Dimensions may vary with other types. All dimensions are shown in inches. Respective
metric dimensions are given in millimeters enclosed by parentheses.
• Where applicable, specifications conform to SAE or ISO standards and are subject to
change without notice.
H
G
A F
24.00
D
48.00 C
(1219)
72.00
(1829)
96.0
(2438)
0 48.0 72.00 96.00 120.0 D–01575
24.0 24.0
(1219) (1829) (2438) (3048)
(610) (610)
115.2
(2926)
90°
90°
115.2
(2926) C–02485
Backhoe
135 of 176 –4–7– Service Manual
BACKHOE SPECIFICATIONS 907 (Cont’d)
630 & 640 Series 730 ,740 Series, 751, 753 & 753H
HYDRAULIC SPECIFICATIONS
Operating Hydraulic Pressure (Loader) . . . . . 1750 PSI (12066 kPa) 2150 PSI (14824 kPa)
Boom Relief Valve Setting:
At Piston Side of Cylinder . . . . . . . . . . . . . . . 2800 PSI (19306 kPa)
At Rod Side of Cylinder . . . . . . . . . . . . . . . . . 3000 PSI (20685 kPa)
Arm Relief Valve Setting:
At Piston Side of Cylinder . . . . . . . . . . . . . . . 2800 PSI (19306 kPa)
Swing Cylinder Relief Setting . . . . . . . . . . . . . 2025 PSI (13962 kPa)
Pump Capacity . . . . . . . . . . . . . . . . . . . . . . . . . . 9.5 GPM (36,0 L/min.) @ 2200 RPM 11 GPM (41,6 L/min. @ 2850 RPM)
& 1900 PSI (13101 kPa) & 2125 PSI (14652 kPa)
Digging Force Using Bucket Cylinder . . . . . . . 4292 lbs. (1949 kg) 5273 lbs (2394 kg)
Digging Force Using Arm Cylinder . . . . . . . . . 2075 lbs. (942 kg) 2549 lbs. (1157 kg)
Hydraulic Lift Capacity, Boom . . . . . . . . . . . . . 565 lbs. (257 kg) 700 lbs. (318 kg)
Hydraulic Lift Capacity, Arm . . . . . . . . . . . . . . . 985 lbs. (447 kg)
Cylinder . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Doubleacting
Bore Dia. Rod Dia. Stroke
Boom Cylinder . . . . . . . . . . . . . . . . . . . . . . . . . 3.00 (76) 1.50 (38) 15.0 (381)
Arm Cylinder . . . . . . . . . . . . . . . . . . . . . . . . . . 3.00 (76) 1.50 (38) 15.0 (381)
Bucket Cylinder . . . . . . . . . . . . . . . . . . . . . . . . 3.00 (76) 1.50 (38) 15.0 (381)
Swing Cylinder . . . . . . . . . . . . . . . . . . . . . . . . . 2.75 (70) 2.75 (70) 8.0 (203)
Stabilizer Cylinder . . . . . . . . . . . . . . . . . . . . . . 1.75 (44) 1.00 (25) 12.0 (305)
Fluid Lines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Standard SAE tubelines, hoses & fittings
TRANSPORT
A Transport Height . . . . . . . . . . . . . . . . . . . . . . 65 (1651)
Stabilizer Spread (Transport) . . . . . . . . . . . 53.2 (1351)
Ground Clearance . . . . . . . . . . . . . . . . . . . . 3.6 (91,4)
Angle of Approach . . . . . . . . . . . . . . . . . . . . 9.5°
OPERATIONAL
C Digging Depth Maximum . . . . . . . . . . . . . . . 94.52 (2401)
D Digging Depth 2 ft. (0,6 m) Flat Bottom . . 93.24 (2368)
Digging Depth 8 ft. (2,4 m) Flat Bottom . . 70.73 (1797)
E Overall Operating Height Fully Raised . . . 101.6 (2581)
F Loading Height Standard Bucket . . . . . . . . 46.1 (1171)
G Loading Reach Standard Bucket . . . . . . . . 52.6 (1336)
H Reach from Swing Pivot . . . . . . . . . . . . . . . 117.0 (2972)
Swing Pivot to Front Wheel . . . . . . . . . . . . . . . 36.7 (932) 36.6 (930)
Weight Distribution:
Front . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3290 Lbs (1494 kg) 3445 lbs. (1564 kg)
Rear . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1900 lbs. (863 kg) 2325 lbs. (1056 kg)
Operating Weight (W/20’’ Bucket) . . . . . . . . . . 5190 lbs (2357 kg) 5770 lbs. (2620 kg)
Backhoe
136 of 176 –4–8– Service Manual
BACKHOE SPECIFICATIONS 909 • Dimensions are given for loader equipped with standard tires and dirt bucket.
Dimensions may vary with other types. All dimensions are shown in inches. Respective
metric dimensions are given in millimeters enclosed by parentheses.
• Where applicable, specifications conform to SAE or ISO standards and are subject to
change without notice.
H
G
B
F
A
24.00
(610)
72.00
(1829)
96.0
(2438)
120.0
(3048)
72.00 96.00 120.0 144.0
24.0 0 24.0 48.0
(1829) (2438) (3048) (3658) PI–02569
(610) (610) (1219)
146.9
(3731)
90°
90°
146.9
(3731)
C–02485
Backhoe
137 of 176 –4–9– Service Manual
BACKHOE SPECIFICATIONS 909 (Cont’d) 730 ,740 Series, 751, 753 & 753H
HYDRAULIC SPECIFICATIONS
Operating Hydraulic Pressure . . . . . . . . . . . . . 2150 PSI (14824 kPa)
Boom Relief Valve Setting:
At Piston Side of Cylinder . . . . . . . . . . . . . . . 2750 PSI (18961 kPa)
At Rod Side of Cylinder . . . . . . . . . . . . . . . . . 3000 PSI (20684 kPa)
Arm Relief Valve Setting:
At Piston Side of Cylinder . . . . . . . . . . . . . . . 2750 PSI (18961 kPa)
At Piston Side of Rod . . . . . . . . . . . . . . . . . . . 3000 PSI (20684 kPa)
Swing Cylinder Relief Setting . . . . . . . . . . . . . 2125 PSI (14652 kPa)
Pump Capacity . . . . . . . . . . . . . . . . . . . . . . . . . . 11 GPM (41,6 L/min.) @ 2850 RPM
Digging Force Using Bucket Cylinder . . . . . . . 4708 lbs. (2140 kg)
Digging Force Using Arm Cylinder . . . . . . . . . 2521 lbs. (1146 kg)
Hydraulic Lift Capacity Boom: (Over End) . . . 500 lbs. (227 kg)
(Swing Arc) . . 490 lbs (223 kg)
Hydraulic Lift Capacity Arm: (Over End) . . . . 1150 lbs. (523 kg)
(Swing Arc) . . . . 720 lbs (327 kg)
Cylinders . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Doubleacting
TRANSPORT
A Transport Height . . . . . . . . . . . . . . . . . . . . . . 78.8 (2002)
Stabilizer Spread (Transport) . . . . . . . . . . . 53.2 (1351)
Ground Clearance . . . . . . . . . . . . . . . . . . . . 3.6 (91)
Angle of Approach . . . . . . . . . . . . . . . . . . . . 8.5°
B Overall Length . . . . . . . . . . . . . . . . . . . . . . . . 173.8 (4413)
Overall Width:
Standard Tires . . . . . . . . . . . . . . . . . . . . . 53.2 (1321)
Flotation Tires . . . . . . . . . . . . . . . . . . . . . . 59.5 (1511)
OPERATIONAL
C Digging Depth Maximum . . . . . . . . . . . . . . . 115.9 (2944)
D Digging Depth 2 ft. (0,6 m) Flat Bottom . . 114.9 (2918)
Digging Depth 8 ft. (2,4 m) Flat Bottom . . 97.6 (2479)
E Overall Operating Height Fully Raised . . . 120.1 (3051)
F Loading Height Standard Bucket Position 69.6 (1768)
G Loading Reach Standard Bucket Position 52.9 (1344)
H Reach from Swing Pivot . . . . . . . . . . . . . . . 146.9 (3731)
Swing Pivot to Front Wheels . . . . . . . . . . . . 37.5 (953)
Bucket Rotation . . . . . . . . . . . . . . . . . . . . . . . . . 153°
Swing Arc . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 180°
Stabilizer Spread (Operating) . . . . . . . . . . . . . 40.4 (1026)
Leveling Angle . . . . . . . . . . . . . . . . . . . . . . . . . . 10°
Controls:
Boom, Arm, Bucket & Swing . . . . . . . . . . . . Two Hand Levers
Stabilizer . . . . . . . . . . . . . . . . . . . . . . . . . . . . Two Hand Levers
Weight Distribution:
Front . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3839 lbs. (1743 kg)
Rear . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2187 lbs. (993 kg)
Backhoe Weight (W/O Bucket) . . . . . . . . . . . . 1350 lbs. (612 kg)
Operating Weight (W/20’’ Bucket) . . . . . . . . . . 6026 lbs. (2736 kg)
Backhoe
138 of 176 –4–10– Service Manual
BACKHOE SPECIFICATIONS 911 • Dimensions are given for loader equipped with standard tires and dirt bucket.
Dimensions may vary with other types. All dimensions are shown in inches. Respective
metric dimensions are given in millimeters enclosed by parentheses.
• Where applicable, specifications conform to SAE or ISO standards and are subject to
change without notice.
H
G
A F
B
24.00
(610)
48.00
96.0
(2438)
120.0
(3048)
144.0
(3658)
157.8
(4008)
90°
90°
157.8
(4008) C–02485
Backhoe
139 of 176 –4–11– Service Manual
BACKHOE SPECIFICATIONS 911
(Cont’d) 843, 853, 853H & 863
HYDRAULIC SPECIFICATIONS
Operating Hydraulic Pressure . . . . . . . . . . 2150 PSI (14824 kPa)
Boom Relief Valve Setting:
At Piston Side of Cylinder . . . . . . . . . . . . 2800 PSI (19303 kPa)
At Rod Side of Cylinder . . . . . . . . . . . . . . 3000 PSI (20684 kPa)
Arm Relief Valve Setting:
At Piston Side of Cylinder . . . . . . . . . . . . 2800 PSI (19303 kPa)
At Piston Side of Rod . . . . . . . . . . . . . . . . 3000 PSI (20684 kPa)
Swing Cylinder Relief Setting . . . . . . . . . . 2125 PSI (14651 kPa)
Pump Capacity . . . . . . . . . . . . . . . . . . . . . . . 16.1 GPM (60,9 L/min.) @ 2700 RPM
Digging Force Using Bucket Cylinder . . . . 4708 lbs. (2140 kg)
Digging Force Using Arm Cylinder . . . . . . 3252 lbs. (1478 kg)
Hydraulic Lift Capacity Boom: (Swing Arc) 913 lbs (414 kg)
Hydraulic Lift Capacity Arm: (Swing Arc) . 1117 lbs (507 kg)
Cylinders . . . . . . . . . . . . . . . . . . . . . . . . . . . . Doubleacting
OPERATIONAL:
C Digging Depth–Maximum . . . . . . . . . . . 135.9 (3452)
D Digging Depth 2 ft. (0,6 m) Flat Bottom 134.9 (3427)
Digging Depth 8 ft. (2,4 m) Flat Bottom 118.2 (3001)
E Overall Operating Height Fully Raised 134.4 (3414)
F Loading Height Standard Bucket Position 82.8 (2103)
G Loading Reach Standard Bucket Position 64.1 (1628)
H Reach From Swing Pivot . . . . . . . . . . . . 157.7 (4005)
Swing Pivot to Front Wheels . . . . . . . . . 41.5 (1054)
Bucket Rotation . . . . . . . . . . . . . . . . . . . . . . 153°
Swing Arc . . . . . . . . . . . . . . . . . . . . . . . . . . . 180°
Stabilizer Spread (Operating) . . . . . . . . . . 75.7 (1923)
Leveling Angle . . . . . . . . . . . . . . . . . . . . . . . 11°
Controls
Boom, Arm, Bucket & Swing . . . . . . . . . . Two Hand Levers
Stabilizers . . . . . . . . . . . . . . . . . . . . . . . . . . Two Hand Levers
Weight Distribution:
Front . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6270 lbs. (2844 kg)
Rear . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1840 lbs. (835 kg)
Backhoe Weight (W/O Bucket) . . . . . . . . . 1760 lbs. (798 kg)
Operting Weight W/20’’ Bucket . . . . . . . . . 8110 lbs. (3679 kg)
Backhoe
140 of 176 –4–12– Service Manual
BACKHOE SPECIFICATIONS 913 • Dimensions are given for loader equipped with standard tires and dirt bucket.
Dimensions may vary with other types. All dimensions are shown in inches. Respective
metric dimensions are given in millimeters enclosed by parentheses.
• Where applicable, specifications conform to SAE or ISO standards and are subject to
change without notice.
H
G
A
F
24.00
199.7
(5072)
90°
127.1
(3228)
90°
199.7
(5072) PI–02684
Backhoe
141 of 176 –4–13– Service Manual
BACKHOE SPECIFICATIONS 913
(Cont’d) 943 & 953
HYDRAULIC SPECIFICATIONS
Operating Hydraulic Pressure . . . . . . . . . . 2400 PSI (16548 kPa)
Boom Relief Valve Setting:
At Piston Side of Cylinder . . . . . . . . . . . . 2500 PSI (17238 kPa)
At Rod Side of Cylinder . . . . . . . . . . . . . . 3500 PSI (24133 kPa)
Arm Relief Valve Setting:
At Piston Side of Cylinder . . . . . . . . . . . . 3000 PSI (20685 kPa)
At Rod Side of Cylinder . . . . . . . . . . . . . . 3000 PSI (20685 kPa)
Swing Cylinder Relief Setting . . . . . . . . . . 2150 PSI (14824 kPa)
Pump Capacity . . . . . . . . . . . . . . . . . . . . . . . 24 GPM (90,8 L/min.) @ 2000 RPM
Digging Force Using Bucket Cylinder . . . . 8500 lbs. (3856 kg)
Digging Force Using Arm Cylinder . . . . . . 4560 lbs. (2068 kg)
Hydraulic Lift Capacity Boom: (Swing Arc) 1325 lbs (601 kg)
Hydraulic Lift Capacity Arm: (Swing Arc) . 2065 lbs (937 kg)
Cylinders . . . . . . . . . . . . . . . . . . . . . . . . . . . . Doubleacting
OPERATIONAL:
C Digging Depth–Maximum . . . . . . . . . . . 163.1 (4143)
D Digging Depth 2 ft. (0,6 m) Flat Bottom 162.3 (4122)
Digging Depth 8 ft. (2,4 m) Flat Bottom 149.6 (3800)
E Overall Operating Height Fully Raised 192.4 (4887)
F Loading Height Standard Bucket Position 112.6 (2860)
G Loading Reach Standard Bucket Position 71.5 (1816)
H Reach From Swing Pivot . . . . . . . . . . . . 199.8 (5072)
Swing Pivot to Front Wheels . . . . . . . . . 42.1 (1069)
Bucket Rotation . . . . . . . . . . . . . . . . . . . . . . 200°
Swing Arc . . . . . . . . . . . . . . . . . . . . . . . . . . . 180°
Stabilizer Spread (Operating) . . . . . . . . . . 127.1 (3228)
Leveling Angle . . . . . . . . . . . . . . . . . . . . . . . 10.6°
Controls
Boom, Arm, Bucket & Swing . . . . . . . . . . Two Hand Levers
Stabilizers . . . . . . . . . . . . . . . . . . . . . . . . . . Two Hand Levers
Backhoe
142 of 176 –4–14– Service Manual
BACKHOE SPECIFICATIONS 607 • Dimensions are given for loader equipped with standard tires and dirt bucket.
Dimensions may vary with other types. All dimensions are shown in inches. Respective
metric dimensions are given in millimeters enclosed by parentheses.
• Where applicable, specifications conform to SAE or ISO standards and are subject to
change without notice.
H
G
A F
24.0 (610)
48.0 (1219)
D C
96.0 (2438)
145.33
90o (3691)
90o
145.33
(3691)
MC–01394
Backhoe
143 of 176 –4–15– Service Manual
BACKHOE SPECIFICATIONS 607 (Cont’d)
640, 740, 750, 760 & 770’S
HYDRAULIC SPECIFICATIONS
Operating Hydraulic Pressure . . . . . . . . . . 2300 PSI (15859 kPa)
Boom Relief Valve Setting:
At Piston Side of Cylinder . . . . . . . . . . . . 2350 PSI (16203 kPa)
At Rod Side of Cylinder . . . . . . . . . . . . . . 3050 PSI (21030 kPa)
Arm Relief Valve Setting:
At Piston Side of Cylinder . . . . . . . . . . . . 3050 PSI (21030 kPa)
At Rod Side of Cylinder . . . . . . . . . . . . . . 2850 PSI (19651 kPa)
Swing Cylinder Relief Setting . . . . . . . . . . 2250 PSI (15514 kPa)
Cylinders . . . . . . . . . . . . . . . . . . . . . . . . . . . . Doubleacting
Bore Dia. Rod Dia. Stroke
Boom Cylinder . . . . . . . . . . . . . . . . . . . . . . . 3.00 (76) 1.50 (38) 19.30 (490)
Arm Cylinder . . . . . . . . . . . . . . . . . . . . . . . . . 3.00 (76 1.50 (38) 17.50 (445)
Bucket Cylinder . . . . . . . . . . . . . . . . . . . . . . 2.75 (70) 2.00 (51) 18.36 (466)
Swing Cylinder . . . . . . . . . . . . . . . . . . . . . . . 2.50 (64) 1.25 (32) 10.35 (263)
Stabilizer Cylinder . . . . . . . . . . . . . . . . . . . . 2.00 (51) 1.00 (25) 20.26 (515)
Fluid Lines . . . . . . . . . . . . . . . . . . . . . . . . . . Standard SAE tubelines, hoses & fittings
Valve . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Four way, 3 position, 6 spool valve
TRANSPORT:
OPERATIONAL:
C Digging Depth–Maximum . . . . . . . . . . . 95.11 (2416)
D Digging Depth 2 ft. (0,6 m) Flat Bottom 93.93 (2386)
Digging Depth 8 ft. (2,4 m) Flat Bottom 72.91 (1852)
E Overall Operating Height Fully Raised 123.13 (3128)
F Loading Height Standard Bucket Position 72.34 (1837)
G Loading Reach Standard Bucket Position 42.56 (1081)
H Reach From Swing Pivot . . . . . . . . . . . . 123.15 (3128)
Swing Pivot to Front Wheels . . . . . . . . . 37.82 (961)
Bucket Rotation . . . . . . . . . . . . . . . . . . . . . . 185°
Swing Arc . . . . . . . . . . . . . . . . . . . . . . . . . . . 180°
Stabilizer Spread (Operating) . . . . . . . . . . 41.29 (1049)
Leveling Angle . . . . . . . . . . . . . . . . . . . . . . . 10.9°
Controls
Boom, Arm, Bucket & Swing . . . . . . . . . . Two Hand Levers
Stabilizers . . . . . . . . . . . . . . . . . . . . . . . . . . Two Hand Levers
Weight Distribution:
Backhoe Weight (W/O Bucket) . . . . . . . . N/A
Backhoe
144 of 176 –4–16– Service Manual
BACKHOE SPECIFICATIONS 709 • Dimensions are given for loader equipped with standard tires and dirt bucket.
Dimensions may vary with other types. All dimensions are shown in inches. Respective
metric dimensions are given in millimeters enclosed by parentheses.
• Where applicable, specifications conform to SAE or ISO standards and are subject to
change without notice.
H
G
A F
24.0 (610)
48.0 (1219)
D C
96.0 (2438)
145.33
90o (3691)
90o
145.33
(3691)
MC–01394
Backhoe
145 of 176 –4–17– Service Manual
BACKHOE SPECIFICATIONS 709 (Cont’d) 740, 750, 760, 770, 850 & 863
HYDRAULIC SPECIFICATIONS
Operating Hydraulic Pressure . . . . . . . . . . . . . 2300 PSI (15859 kPa)
Boom Relief Valve Setting:
At Piston Side of Cylinder . . . . . . . . . . . . . . . 2350 PSI (16203 kPa)
At Rod Side of Cylinder . . . . . . . . . . . . . . . . . 3050 PSI (21030 kPa)
Dipper Relief Valve Setting:
At Piston Side of Cylinder . . . . . . . . . . . . . . . 3050 PSI (21030 kPa)
At Rod Side of Cylinder . . . . . . . . . . . . . . . . . 2850 PSI (19651 kPa)
Swing Cylinder Relief Setting . . . . . . . . . . . . . 2250 PSI (15514 kPa)
Cylinder . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Doubleacting
Bore Dia. Rod Dia. Stroke
Boom Cylinder . . . . . . . . . . . . . . . . . . . . . . . . . 3.00 (76) 1.50 (38) 19.30 (490)
Arm Cylinder . . . . . . . . . . . . . . . . . . . . . . . . . . 3.00 (76 1.50 (38) 17.50 (445)
Bucket Cylinder . . . . . . . . . . . . . . . . . . . . . . . . 2.75 (70) 2.00 (51) 18.36 (466)
Swing Cylinder . . . . . . . . . . . . . . . . . . . . . . . . . 2.50 (64) 1.25 (32) 10.35 (263)
Stabilizer Cylinder . . . . . . . . . . . . . . . . . . . . . . 2.00 (51) 1.00 (25) 20.26 (515)
Fluid Lines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Standard SAE tubelines, hoses & fittings
Valve . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Four way, 3 position, 6 spool valve
OPERATIONAL:
C Digging Depth–Maximum . . . . . . . . . . . . . . 116.63 (2662)
D Digging Depth 2 ft. (0,6 m) Flat Bottom . . 115.64 (2937)
Digging Depth 8 ft. (2,4 m) Flat Bottom . . 98.29 (2497)
E Overall Operating Height Fully Raised . . . 142.97 (3631)
F Loading Height Standard Bucket Position 83.28 (2115)
G Loading Reach Standard Bucket Position 48.63 (1235)
H Reach From Swing Pivot . . . . . . . . . . . . . . . 145.33 (3691)
Swing Pivot to Front Wheels . . . . . . . . . . . . . . 37.23 (946)
Bucket Rotation . . . . . . . . . . . . . . . . . . . . . . . . . 200o
Swing Arc . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 180o
Stabilizer Spread (Operating) (Telescopic) . . 41.37 (1051)
Controls:
Boom, Arm, Bucket & Swing . . . . . . . . . . . . Two Hand Levers
Stabilizers . . . . . . . . . . . . . . . . . . . . . . . . . . . Two Hand Levers
Weight Distribution:
Backhoe Weight (W/O Bucket) . . . . . . . . . . . . 1522 lbs. (690 kg)
Backhoe
146 of 176 –4–18– Service Manual
8709 BACKHOE SPECIFICATIONS • All dimensions are shown in inches. Respective metric dimensions are given in
millimeters enclosed by parentheses.
• Where applicable, specifications conform to SAE or ISO standards and are subject to
change without notice.
F
A
G
24.0 (610)
96.0 (2438)
120.0 (3048)
48.0 96.0 144.0
0 (1219) (2438) (3658)
24.0 24.0 72.0 120.0 MC–02148
(610) (610) (1829) (3658)
146
90o (3695)
90o
146
(3695) MC–01394
Backhoe
147 of 176 –4–19– Service Manual
8709 BACKHOE SPECIFICATIONS (Cont’d) 873
HYDRAULIC SPECIFICATIONS
Operating Hydraulic Pressure . . . . . . . . . . . . . 2300 PSI (15859 kPa)
Boom Relief Valve Setting:
At Piston Side of Cylinder . . . . . . . . . . . . . . . 2350 PSI (16203 kPa)
At Rod Side of Cylinder . . . . . . . . . . . . . . . . . 3050 PSI (21030 kPa)
Arm Relief Valve Setting:
At Piston Side of Cylinder . . . . . . . . . . . . . . . 3050 PSI (21030 kPa)
At Rod Side of Cylinder . . . . . . . . . . . . . . . . . 2850 PSI (19651 kPa)
Swing Cylinder Relief Setting . . . . . . . . . . . . . 2250 PSI (15514 kPa)
Cylinder . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Doubleacting
Bore Dia. Rod Dia. Stroke
Boom Cylinder . . . . . . . . . . . . . . . . . . . . . . . . . 3.25 (83) 1.50 (38) 21.44 (545)
Arm Cylinder . . . . . . . . . . . . . . . . . . . . . . . . . . 3.25 (83) 1.50 (38) 21.44 (545)
Bucket Cylinder . . . . . . . . . . . . . . . . . . . . . . . . 2.75 (70) 2.00 (51) 23.05 (586)
Swing Cylinder . . . . . . . . . . . . . . . . . . . . . . . . . 3.00 (76) 1.25 (32) 10.47 (266)
Stabilizer Cylinder . . . . . . . . . . . . . . . . . . . . . . 2.75 (70) 1.75 (45) 14.00 (356)
Fluid Lines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Standard SAE tubelines, hoses & fittings
Valve . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Four way, 3 position, 6 spool valve
TRANSPORT
OPERATIONAL
C Digging Depth–Maximum . . . . . . . . . . . . . . 118 (2999)
D Digging Depth 2 ft. (0,6 m) Flat Bottom . . 117 (2974)
E Digging Depth 8 ft. (2,4 m) Flat Bottom . . 100 (2533)
F Overall Operating Height Fully Raised . . . 142 (3595)
G Loading Height Standard Bucket Position 82 (2079)
Loading Reach Standard Bucket Position 48.63 (1235)
J Reach From Swing Pivot . . . . . . . . . . . . . . . 146 (3695)
Swing Pivot to Front Wheels . . . . . . . . . . . . . . 38 (953)
Bucket Rotating . . . . . . . . . . . . . . . . . . . . . . . . . 200o
Swing Arc . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 180o
Stabilizer Spread (Operating Position) . . . . . . 100 (2549)
Controls:
Boom, Arm, Bucket & Swing . . . . . . . . . . . . Two Hand Levers
Stabilizers . . . . . . . . . . . . . . . . . . . . . . . . . . . Two Hand Levers
Weight Distribution:
Backhoe Weight (W/O Bucket) . . . . . . . . . . . . 1640 lbs. (744 kg)
* STABILITY IS LIMITED
Backhoe
148 of 176 –4–20– Service Manual
BACKHOE SPECIFICATIONS 811 • Dimensions are given for loader equipped with standard tires and dirt bucket.
Dimensions may vary with other types. All dimensions are shown in inches. Respective
metric dimensions are given in millimeters enclosed by parentheses.
• Where applicable, specifications conform to SAE or ISO standards and are subject to
change without notice.
I
H
A G
24.0 (610)
48.0 (1219)
96.0 (2438)
120.0 (3048)
144 (3658)
24.0 24.0 72.0 120.0 168
(610) (610) (1829) (3048) (4267)
48.0 0 48.0 96.0 144.0 MC–01446
(1219) (1219) (2438) (3658)
166.0
(4216)
90o
90o
166.0
(4216)
MC–01445
Backhoe
149 of 176 –4–21– Service Manual
BACKHOE SPECIFICATIONS 811 843, 853, 853H, 863 & 963
(Cont’d)
HYDRAULIC SPECIFICATIONS
Operating Hydraulic Pressure . . . . . . . . . . 2300 PSI (15859 kPa)
Cylinder . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Doubleacting
Bore Dia. Rod Dia. Stroke
Boom Cylinder . . . . . . . . . . . . . . . . . . . . . . 3.50 (89) 1.50 (38) 25.7 (654)
Arm Cylinder . . . . . . . . . . . . . . . . . . . . . . . 3.50 (89) 1.75 (44) 25.7 (654)
Bucket Cylinder . . . . . . . . . . . . . . . . . . . . . 3.00 (76) 2.00 (51) 23.05 (586)
Swing Cylinder . . . . . . . . . . . . . . . . . . . . . . 3.75 (95) 1.50 (38) 10.47 (266)
Stabilizer Cylinder . . . . . . . . . . . . . . . . . . . 3.00 (76) 1.50 (38) 14.25 (362)
Fluid Lines . . . . . . . . . . . . . . . . . . . . . . . . . .
TRANSPORT
A Transport Height . . . . . . . . . . . . . . . . . . . 106.9 (2715)
Stabilizer Spread (transport) . . . . . . . . . 70.3 (1786)
Ground Clearance . . . . . . . . . . . . . . . . . 6.9 (175)
Angle of Approach . . . . . . . . . . . . . . . . . 12.3o
B Overall Length . . . . . . . . . . . . . . . . . . . . . 177.5 (4509)
Overall Width:
Standard Tires . . . . . . . . . . . . . . . . . . . . 81.98 (2082)
Flotation Tires . . . . . . . . . . . . . . . . . . . . 81.98 (2082)
OPERATIONAL
C Digging Depth–Maximum . . . . . . . . . . . 135.7 (3447)
D Digging Depth 2 ft. (0,6 m) Flat Bottom 134.8 (3424)
E Digging Depth 8 ft. (2,4 m) Flat Bottom 119.3 (3030)
F Overall Operating Height Fully Raised 161.0 (4089)
G Loading Height Standard Bucket Position 100.0 (2540
H Loading Reach Standard Bucket Position 59.2 (1504)
I Reach From Swing Pivot . . . . . . . . . . . . 166.0 (4216)
Swing Pivot to Front Wheels . . . . . . . . . . . 39.9 (1014)
Bucket Rotation . . . . . . . . . . . . . . . . . . . . . . 200o
Swing Arc . . . . . . . . . . . . . . . . . . . . . . . . . . . 180o
Stabilizer Spread (Operating) . . . . . . . . . . 130.1 (3310)
Leveling Angle . . . . . . . . . . . . . . . . . . . . . . . 11.7o
Controls:
Boom, Arm, Bucket & Swing . . . . . . . . . Two Hand Levers
Stabilizers . . . . . . . . . . . . . . . . . . . . . . . . Two Hand Levers
Weight Distribution:
Backhoe Weight (W/O Bucket) . . . . . . . 2012 lbs. (913 kg)
Backhoe
150 of 176 –4–22– Service Manual
BACKHOE SPECIFICATIONS 911B • Dimensions are given for loader equipped with standard tires and dirt bucket.
Dimensions may vary with other types. All dimensions are shown in inches. Respective
metric dimensions are given in millimeters enclosed by parentheses.
• Where applicable, specifications conform to SAE or ISO standards and are subject to
change without notice.
157.8
(4008) H
90o
G
77.4
(19.66)
90o
F E
MC–01148
157.8
(4008)
24.0 (610)
48.0 (1219)
96.0 (2438)
120.0 (3048)
144 (3658)
74.9 0 48.0 96.0 144.0
48.0
(1902) (1219) (2438) (3658)
(1219)
24.0 24.0 72.0 120.0 168
(610) (610) (1829) (3048) (4267)
MC–01245
10° A
77.4
(1966)
125.7
(3193)
MC–01152
MC–01246
Backhoe
151 of 176 –4–23– Service Manual
BACKHOE SPECIFICATIONS 911B 2400 & 2410
(Cont’d)
OPERATION & PERFORMANCE
Weights
*Operating Weight . . . . . . . . . . . . . . . . . . . N/A
911B Backhoe . . . . . . . . . . . . . . . . . . . . . . N/A
Lifting Capaicty – Loader . . . . . . . . . . . . . 4000 lbs. (1816 kg)
HYDRAULIC SYSTEMS
Operating Hydraulic Pressure . . . . . . . . . . 2500 PSI (17238 kPa)
Boom Relief Valve Setting:
At Piston Side of Cylinder . . . . . . . . . . . . 2500 PSI (17238 kPa)
At Rod Side of Cylinder . . . . . . . . . . . . . . 3500 PSI (24133 kPa)
Arm Relief Valve Setting:
At Piston Side of Cylinder . . . . . . . . . . . . 3000 PSI (20685 kPa)
At Rod Side of Cylinder . . . . . . . . . . . . . . 3000 PSI (20685 kPa)
Swing Cylinder Relief Setting . . . . . . . . . . 2150 PSI (14824 kPa)
Bucket Relief Valve Setting:
At Piston Side of Cylinder . . . . . . . . . . . . 3000 PSI (20685 kPa)
At Rod Side of Cylinder . . . . . . . . . . . . . . 3500 PSI (24133 kPa)
Cylinders . . . . . . . . . . . . . . . . . . . . . . . . . . . . Doubleacting
TRANSPORT
A Transport Height . . . . . . . . . . . . . . . . . . . 125.0 (3175)
Stabilizer Spread (Transport) W/Pads . 74.9 (1902)
Ground Clearance . . . . . . . . . . . . . . . . . 14.4 (366)
Angle of Approach . . . . . . . . . . . . . . . . . 21.5°
B Overall Length (Transport) . . . . . . . . . . 216.1 (5489)
Overall Width:
Standard Pads . . . . . . . . . . . . . . . . . . . 74.9 (1902)
Loader Bucket . . . . . . . . . . . . . . . . . . . . 77.4 (1966)
OPERATIONAL
C Digging Depth–Maximum . . . . . . . . . . . 133.0 (3378)
D Digging Depth 2 ft. (0,6 m) Flat Bottom 132.0 (3353)
Digging Depth 8 ft. (2,4 m) Flat Bottom 115.2 (2926)
E Overall Operating Height Fully Raised
F Loading Height . . . . . . . . . . . . . . . . . . . . 85.7 (2177)
G Loading Reach . . . . . . . . . . . . . . . . . . . . 66.1 (1679)
H Reach From Swing Pivot . . . . . . . . . . . . 159.9 (4061)
Swing Pivot to Front Wheels . . . . . . . . . 41.8 (1062)
Bucket Rotation . . . . . . . . . . . . . . . . . . . . . . 172°
Swing Arc . . . . . . . . . . . . . . . . . . . . . . . . . . . 180°
Stabilizer Spread (Operating) . . . . . . . . . . 125.7 (3193)
Leveling Angle . . . . . . . . . . . . . . . . . . . . . . . 10°
Controls:
Boom, Arm, Bucket & Swing . . . . . . . . . Two Hand Levers
Stabilizers . . . . . . . . . . . . . . . . . . . . . . . . Two Hand Levers
* Machine equipped with 14x17.5 tires, 77’’ Dirt Bucket, ROPS, 911B Backhoe, 24’’ Bucket, full fuel and 175 lbs.
(79 kg) operator.
Backhoe
152 of 176 –4–24– Service Manual
BACKHOE SPECIFICATIONS 914B
BackhoeServiceManual#6900622– SpecificationsSectionPart1of2
• Dimensions are given for loader equipped with standard tires and dirt bucket.
Dimensions may vary with other types. All dimensions are shown in inches. Respective
metric dimensions are given in millimeters enclosed by parentheses.
• Where applicable, specifications conform to SAE or ISO standards and are subject to
change without notice.
206.4
(5243) H
90o G
90o
E
F
MC–01148
206.4
(5243)
24.0 (610)
48.0 (1219)
10°
21.5°
77.4
(1966)
125.7
(3193)
14.4
MC–01152 (366)
B
MC–01150
Backhoe
153 of 176 –4–25– Service Manual
BACKHOE SPECIFICATIONS 914B 2400 & 2410
(Cont’d)
OPERATION & PERFORMANCE
Weights
*Operating Weight . . . . . . . . . . . . . . . . . . . 12158 lbs (5520 kg)
914B Backhoe . . . . . . . . . . . . . . . . . . . . . . 2650 lbs (1189 kg)
Lifting Capaicty – Loader . . . . . . . . . . . . . 4000 lbs. (1816 kg)
HYDRAULIC SYSTEMS
Operating Hydraulic Pressure . . . . . . . . . . 2500 PSI (17238 kPa)
Boom Relief Valve Setting:
At Piston Side of Cylinder . . . . . . . . . . . . 2500 PSI (17238 kPa)
At Rod Side of Cylinder . . . . . . . . . . . . . . 3500 PSI (24133 kPa)
Arm Relief Valve Setting:
At Piston Side of Cylinder . . . . . . . . . . . . 3000 PSI (20685 kPa)
At Rod Side of Cylinder . . . . . . . . . . . . . . 3000 PSI (20685 kPa)
Swing Cylinder Relief Setting . . . . . . . . . . 2150 PSI (14824 kPa)
Bucket Relief Valve Setting:
At Piston Side of Cylinder . . . . . . . . . . . . 3000 PSI (20685 kPa)
At Rod Side of Cylinder . . . . . . . . . . . . . . 3500 PSI (24133 kPa)
TRANSPORT
A Transport Height . . . . . . . . . . . . . . . . . . . 141.1 (3584)
Stabilizer Spread (Transport) W/Pads . 74.9 (1902)
Ground Clearance . . . . . . . . . . . . . . . . . 14.4 (366)
Angle of Approach . . . . . . . . . . . . . . . . . 21.5°
B Overall Length (Transport) . . . . . . . . . . 215.5 (5474)
Overall Width:
Standard Pads . . . . . . . . . . . . . . . . . . . 74.9 (1902)
Loader Bucket . . . . . . . . . . . . . . . . . . . . 77.4 (1966)
OPERATIONAL
C Digging Depth–Maximum . . . . . . . . . . . 172.5 (4382)
D Digging Depth 2 ft. (0,6 m) Flat Bottom 171.8 (4364)
Digging Depth 8 ft. (2,4 m) Flat Bottom 159.9 (4061)
E Overall Operating Height Fully Raised 195.0 (4953)
F Loading Height . . . . . . . . . . . . . . . . . . . . 105.0 (2667)
G Loading Reach . . . . . . . . . . . . . . . . . . . . 68.3 (1735)
H Reach From Swing Pivot . . . . . . . . . . . . 206.4 (5232)
Swing Pivot to Front Wheels . . . . . . . . . 41.8 (1062)
Bucket Rotation . . . . . . . . . . . . . . . . . . . . . . 200°
Swing Arc . . . . . . . . . . . . . . . . . . . . . . . . . . . 180°
Stabilizer Spread (Operating) . . . . . . . . . . 125.7 (3193)
Leveling Angle . . . . . . . . . . . . . . . . . . . . . . . 10°
Controls:
Boom, Arm, Bucket & Swing . . . . . . . . . Two Hand Levers
Stabilizers . . . . . . . . . . . . . . . . . . . . . . . . Two Hand Levers
* Machine equipped with 14x17.5 tires, 77’’ Dirt Bucket, ROPS, 914B Backhoe, High Capcity Bucket (P/N 6648081),
full fuel and 175 lbs. (79 kg) operator.
Backhoe
154 of 176 –4–26– Service Manual
BACKHOE SPECIFICATIONS 914B • Dimensions are given for loader equipped with standard tires and dirt bucket.
EXTENDABLE Dimensions may vary with other types. All dimensions are shown in inches. Respective
metric dimensions are given in millimeters enclosed by parentheses.
74.9
(1902) • Where applicable, specifications conform to SAE or ISO standards and are subject to
change without notice.
H
G
10°
F E
77.4
(1966)
125.7
(3193)
MC–01268
24.0 (610)
48.0 (1219)
245.8
(6243)
90°
77.4
(1966)
90°
245.8 21.5°
(6243)
15.1
(384)
MC–01267
MC–01269
Backhoe
155 of 176 –4–27– Service Manual
BACKHOE SPECIFICATIONS 914B 2400 & 2410
EXTENDABLE (Cont’d)
OPERATION & PERFORMANCE
Weights
*Operating Weight . . . . . . . . . . . . . . . . . . . N/A
914B Extendable Backhoe . . . . . . . . . . . N/A
Lifting Capaicty – Loader . . . . . . . . . . . . . 4000 lbs. (1816 kg)
HYDRAULIC SYSTEMS
Operating Hydraulic Pressure . . . . . . . . . . 2500 PSI (17238 kPa)
Boom Relief Valve Setting:
At Piston Side of Cylinder . . . . . . . . . . . . 2500 PSI (17238 kPa)
At Rod Side of Cylinder . . . . . . . . . . . . . . 3500 PSI (24133 kPa)
Arm Relief Valve Setting:
At Piston Side of Cylinder . . . . . . . . . . . . 3000 PSI (20685 kPa)
At Rod Side of Cylinder . . . . . . . . . . . . . . 3000 PSI (20685 kPa)
Swing Cylinder Relief Setting . . . . . . . . . . 2150 PSI (14824 kPa)
Bucket Relief Valve Setting:
At Piston Side of Cylinder . . . . . . . . . . . . 3000 PSI (20685 kPa)
At Rod Side of Cylinder . . . . . . . . . . . . . . 3500 PSI (24133 kPa)
TRANSPORT
A Transport Height . . . . . . . . . . . . . . . . . . . 150.1 (3813)
Stabilizer Spread (Transport) W/Pads . 74.9 (1902)
Ground Clearance . . . . . . . . . . . . . . . . . 14.4 (366)
Angle of Approach . . . . . . . . . . . . . . . . . 21.5°
B Overall Length (Transport) . . . . . . . . . . 214.5 (5448)
Overall Width:
Stabilizer Pads . . . . . . . . . . . . . . . . . . . 74.9 (1902)
Loader Bucket . . . . . . . . . . . . . . . . . . . . 77.4 (1966)
OPERATIONAL
C Digging Depth–Maximum . . . . . . . . . . . 213.8 (5431)
D Digging Depth 2 ft. (0,6 m) Flat Bottom 213.8 (5431)
Digging Depth 8 ft. (2,4 m) Flat Bottom 204.0 (5182)
Straight Wall Digging Dept–Tooth . . . . 192.4 (4887)
Cutting Edge . . . . 186.7 (4742)
E Overall Operating Height Fully Raised 221.3 (5621)
F Loading Height . . . . . . . . . . . . . . . . . . . . 130.6 (3317)
G Loading Reach . . . . . . . . . . . . . . . . . . . . 114.2 (2901)
H Reach From Swing Pivot . . . . . . . . . . . . 245.8 (6234)
Swing Pivot to Front Wheels . . . . . . . . . 41.8 (1062)
Bucket Rotation . . . . . . . . . . . . . . . . . . . . . . 200°
Swing Arc . . . . . . . . . . . . . . . . . . . . . . . . . . . 180°
Stabilizer Spread (Operating) . . . . . . . . . . 125.7 (3193)
Leveling Angle . . . . . . . . . . . . . . . . . . . . . . . 10°
Controls:
Boom, Arm, Bucket & Swing . . . . . . . . . Two Hand Levers
Stabilizers . . . . . . . . . . . . . . . . . . . . . . . . Two Hand Levers
* Machine equipped with 14x17.5 tires, 77’’ Dirt Bucket, ROPS, 937S Backhoe, High Capcity Bucket (P/N 6648081),
full fuel and 175 lbs. (79 kg) operator and fromt counterweight.
Backhoe
156 of 176 –4–28– Service Manual
BACKHOE SPECIFICATIONS 725S • Dimensions are given for loader equipped with standard tires and dirt bucket.
Dimensions may vary with other types. All dimensions are shown in inches. Respective
metric dimensions are given in millimeters enclosed by parentheses.
• Where applicable, specifications conform to SAE or ISO standards and are subject to
change without notice.
H
G
B
E
A F
24 (610)
48 (1219) D C
96 (2438)
24 24 72 120 MC–01173
(610) (610) (1829) (3048)
0 48 96
(1219) (2438)
124
(3161)
J
90 °
47 (1199)
48 (1217)
90 °
124
(3161)
MC–01174
Backhoe
157 of 176 –4–29– Service Manual
BACKHOE SPECIFICATIONS 725S (Cont’d) 540 SERIES, 600 SERIES, 730, 740 SERIES, 751, 753 & 753H
HYDRAULIC SPECIFICATIONS
Operating Hydraulic Pressure . . . . . . . . . . . . . . . 1575 PSI (10860 kPa)
Cylinder . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Doubleacting
Bore Dia. Rod Dia. Stroke
Boom Cylinder . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.99 (76) 1.50 (38) 19.3 (490)
Arm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.99 (76) 1.50 (38) 17.5 (444)
Bucket Cylinder . . . . . . . . . . . . . . . . . . . . . . . . . . 2.76 (70) 2.00 (51) 18.3 (466)
Swing Cylinder . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.52 (64) 1.50 (38) 8.27 (210)
Stabilizer Cylinder . . . . . . . . . . . . . . . . . . . . . . . . 2.00 (51) 0.98 (25) 19.7 (500)
Fluid Lines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Standard SAE tubelines, hoses & fittings
Valve . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Six section, four way, stack type
OPERATIONAL:
C Digging Depth–Maximum . . . . . . . . . . . . . . . . 98.5 (2503)
D Digging Depth 2 ft. (0,6 m) Flat Bottom . . . . 97.3 (2472)
Digging Depth 8 ft. (2,4 m) Flat Bottom . . . . 76.3 (1939)
E Overall Operating Height Fully Raised . . . . . 120 (3040)
F Loading Height Standard Bucket Position . . 69 (1750)
G Loading Reach Standard Bucket Position . . 44 (1114)
H Reach From Swing Pivot . . . . . . . . . . . . . . . . . 124 (3161)
Swing Pivot to Front Wheels . . . . . . . . . . . . . . . . 37 (932)
Bucket Rotation . . . . . . . . . . . . . . . . . . . . . . . . . . . 185°
Swing Arc . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 180°
Stabilizer Spread (Operating) . . . . . . . . . . . . . . . 48 (1222)
J Leveling Angle . . . . . . . . . . . . . . . . . . . . . . . . . . 18.9°
Controls:
Boom, Arm, Bucket & Swing . . . . . . . . . . . . . . Two Hand Levers
Stabilizers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Two Hand Levers
Weight Distribution:
Front . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . N/A
Rear . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . N/A
Backhoe
158 of 176 –4–30– Service Manual
BACKHOE SPECIFICATIONS 730S • Dimensions are given for loader equipped with standard tires and dirt bucket.
Dimensions may vary with other types. All dimensions are shown in inches. Respective
metric dimensions are given in millimeters enclosed by parentheses.
• Where applicable, specifications conform to SAE or ISO standards and are subject to
change without notice.
E
G
A F
24.0
90 °
90 °
146.8
(3729)
J
48.23
(1225)
60.98
(1549) MC–01538
MC–01174
Backhoe
159 of 176 –4–31– Service Manual
BACKHOE SPECIFICATIONS 730S (Cont’d)
730, 740 SERIES
HYDRAULIC SPECIFICATIONS
Operating Hydraulic Pressure . . . . . . . . . . . . . 2150 PSI (14824 kPa)
Cylinder . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Doubleacting
Bore Dia. Rod Dia. Stroke
Boom Cylinder . . . . . . . . . . . . . . . . . . . . . . . . . 3.25 (83) 1.50 (38) 21.44 (545)
Arm Cylinder . . . . . . . . . . . . . . . . . . . . . . . . . . 3.25 (83) 1.50 (38) 21.44 (545)
Bucket Cylinder . . . . . . . . . . . . . . . . . . . . . . . . 2.75 (70) 2.00 (51) 23.05 (586)
Swing Cylinder . . . . . . . . . . . . . . . . . . . . . . . . . 3.00 (76) 1.50 (38) 8.27 (210)
TRANSPORT:
A Transport Height . . . . . . . . . . . . . . . . . . . . . . 91.45 (2323)
Stabilizer Spread (Transport) . . . . . . . . . . . 60.98 (1549)
Ground Clearance . . . . . . . . . . . . . . . . . . . . 3.5 (89)
Angle of Approach . . . . . . . . . . . . . . . . . . . . 9.8°
B Overall Length . . . . . . . . . . . . . . . . . . . . . . . . 166.3 (4223)
Overall Width:
Standard Tires . . . . . . . . . . . . . . . . . . . . . 60.98 (1549)
Flotation . . . . . . . . . . . . . . . . . . . . . . . . . . . 60.98 (1549)
OPERATIONAL:
Straight Wall Digging Depth 79.8 (2028)
C Digging Depth–Maximum . . . . . . . . . . . . . . 118.3 (3004)
D Digging Depth 2 ft. (0,6 m) Flat Bottom . . 117.24 (2978)
Digging Depth 8 ft. (2,4 m) Flat Bottom . . 99.9 (2538)
E Overall Operating Height Fully Raised . . . 141.4 (3591)
F Loading Height Standard Bucket Position 81.7 (2074)
G Loading Reach Standard Bucket Position 50.0 (1270)
H Reach From Swing Pivot . . . . . . . . . . . . . . . 146.8 (3729)
Swing Pivot to Front Wheels . . . . . . . . . . . . . . 22.97 (583)
Bucket Rotation . . . . . . . . . . . . . . . . . . . . . . . . . 200°
Swing Arc . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 180°
Stabilizer Spread (Operating) . . . . . . . . . . . . . 48.23 (1225)
J Leveling Angle . . . . . . . . . . . . . . . . . . . . . . . . 12°
Side Shift . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33.7 (856)
Controls:
Boom, Arm, Bucket, & Swing . . . . . . . . . . . Two Hand Levers
Stabilizers . . . . . . . . . . . . . . . . . . . . . . . . . . . Two Hand Levers
Weight Distribution:
Front . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . N/A
Rear . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . N/A
Backhoe
160 of 176 –4–32– Service Manual
BACKHOE SPECIFICATIONS 730S • Dimensions are given for loader equipped with standard tires and dirt bucket.
(Cont’d) Dimensions may vary with other types. All dimensions are shown in inches. Respective
metric dimensions are given in millimeters enclosed by parentheses.
• Where applicable, specifications conform to SAE or ISO standards and are subject to
change without notice.
E
G
A F
24.0 (610)
48.0 (1219) D
C
96.0 (2438)
120.0 (3048)
146.8
(3729)
90 °
90 ° 146.8 J
(3729) 48.23
(1225)
60.98
(1549)
MC–01174
MC–01538
Backhoe
161 of 176 –4–33– Service Manual
BACKHOE SPECIFICATIONS 730S (Cont’d)
753L, 763, 7753 & 773
HYDRAULIC SPECIFICATIONS
Operating Hydraulic Pressure . . . . . . . . . . . . . 2150 PSI (14824 kPa)
Cylinder . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Doubleacting
Bore Dia. Rod Dia. Stroke
Boom Cylinder . . . . . . . . . . . . . . . . . . . . . . . . . 3.25 (83) 1.50 (38) 21.44 (545)
Arm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.25 (83) 1.50 (38) 21.44 (545)
Bucket Cylinder . . . . . . . . . . . . . . . . . . . . . . . . 2.75 (70) 2.00 (51) 23.05 (586)
Swing Cylinder . . . . . . . . . . . . . . . . . . . . . . . . . 3.00 (76) 1.50 (38) 8.27 (210)
TRANSPORT:
A Transport Height . . . . . . . . . . . . . . . . . . . . . . 91.8 (2331)
Stabilizer Spread (Transport) . . . . . . . . . . . 60.98 (1549)
Ground Clearance . . . . . . . . . . . . . . . . . . . . 3.8 (97)
Angle of Approach . . . . . . . . . . . . . . . . . . . . 7.9°
B Overall Length . . . . . . . . . . . . . . . . . . . . . . . . 167.4 (4253)
Overall Width:
Standard Tires . . . . . . . . . . . . . . . . . . . . . 60.98 (1549)
Flotation . . . . . . . . . . . . . . . . . . . . . . . . . . . 60.98 (1549)
OPERATIONAL:
Straight Wall Digging Depth 79.5 (2020)
C Digging Depth–Maximum . . . . . . . . . . . . . . 117.9 (2995)
D Digging Depth 2 ft. (0,6 m) Flat Bottom . . 116.9 (2970)
Digging Depth 8 ft. (2,4 m) Flat Bottom . . 99.6 (2529)
E Overall Operating Height Fully Raised . . . 141.7 (3599)
F Loading Height Standard Bucket Position 82.0 (2083)
G Loading Reach Standard Bucket Position 50.0 (1270)
H Reach From Swing Pivot . . . . . . . . . . . . . . . 146.8 (3729)
Swing Pivot to Front Wheels . . . . . . . . . . . . . . 23.6 (600)
Bucket Rotation . . . . . . . . . . . . . . . . . . . . . . . . . 200°
Swing Arc . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 180°
Stabilizer Spread (Operating) . . . . . . . . . . . . . 48.23 (1225)
J Leveling Angle . . . . . . . . . . . . . . . . . . . . . . . . 12°
Side Shift . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33.7 (856)
Controls:
Boom, Arm, Bucket, & Swing . . . . . . . . . . . Two Hand Levers
Stabilizers . . . . . . . . . . . . . . . . . . . . . . . . . . . Two Hand Levers
Weight Distribution:
Front . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . N/A
Rear . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . N/A
Backhoe
162 of 176 –4–34– Service Manual
BACKHOE SPECIFICATIONS 923S • Dimensions are given for loader equipped with standard tires and dirt bucket.
Dimensions may vary with other types. All dimensions are shown in inches. Respective
metric dimensions are given in millimeters enclosed by parentheses.
• Where applicable, specifications conform to SAE or ISO standards and are subject to
change without notice.
H
G
B
A
F
24
(610)
48 D
(1219) C
90 °
41 J
(1051)
90
H 54
(1511)
MC–01202
MC–01174
Backhoe
163 of 176 –4–35– Service Manual
BACKHOE SPECIFICATIONS 923S (Cont’d) 630 & 640 Series 730, 743, 751, 753 & 753H
HYDRAULIC SPECIFICATIONS
Operating Hydraulic Pressure . . . . . . . . . . . . . . 1900 PSI (13100 kPa) 2124 PSI (14650 kPa)
Pump Capacity . . . . . . . . . . . . . . . . . . . . . . . . . . . 9.0 GPM (34,1 L/min.) @ 2500 RPM 10 GPM (38 L/min.) @ 2800 RPM
1750 PSI (12066 kPa) 2150 PSI (14824 kPa)
Digging Force Using Bucket Cylinder . . . . . . . . 4292 lbs. (1951 kg) 5273 lbs. (2397 kg)
Digging Force Using Arm Cylinder . . . . . . . . . . 2075 lbs. (943 kg) 2549 lbs. (1157 kg)
Hydraulic Lift Capacity, Boom . . . . . . . . . . . . . . 566 lbs. (257 kg) 761 lbs. (345 kg)
Hydraulic Lift Capacity, Arm . . . . . . . . . . . . . . . . 914 lbs. (415 kg) 1000 lbs. (454 kg)
Cylinder . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Doubleacting
Bore Dia. Rod Dia. Stroke
Boom Cylinder . . . . . . . . . . . . . . . . . . . . . . . . . . 3.0 (76) 1.5 (38) 15.0 (381)
Arm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.0 (76) 1.5 (38) 15.0 (381)
Bucket Cylinder . . . . . . . . . . . . . . . . . . . . . . . . . 3.0 (76) 1.5 (38) 15.0 (381)
Swing Cylinder . . . . . . . . . . . . . . . . . . . . . . . . . . 2.5 (64) 1.25 (32) 5.7 (145)
Stabilizer Cylinder . . . . . . . . . . . . . . . . . . . . . . . 2.0 (51) 1.0 (25) 19.7 (500)
Fluid Lines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Standard SAE tubelines, hoses & fittings
Valve . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Six section, four way, stack type
OPERATIONAL:
C Digging Depth–Maximum . . . . . . . . . . . . . . . 91 (2313)
D Digging Depth 2 ft. (0,6 m) Flat Bottom . . . 90 (2281)
Digging Depth 8 ft. (2,4 m) Flat Bottom . . . 67 (1709)
E Overall Operating Height Fully Raised . . . . 105 (2667)
F Loading Height Standard Bucket Position . 49.5 (1256)
G Loading Reach Standard Bucket Position . 52 (1321)
H Reach From Swing Pivot . . . . . . . . . . . . . . . . 116 (2945)
Swing Pivot to Front Wheels . . . . . . . . . . . . . . . 37 (946)
Controls:
Boom, Arm, Bucket & Swing . . . . . . . . . . . . . Two Hand Levers
Stabilizers . . . . . . . . . . . . . . . . . . . . . . . . . . . . Two Hand Levers
Weight Distribution:
Front . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3133 lbs. (1421 kg) 2952 lbs. (1339 kg)
Rear . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2101 lbs. (953 kg) 2814 lbs. (1276 kg)
Backhoe
164 of 176 –4–36– Service Manual
BACKHOE SPECIFICATIONS 923SA • Dimensions are given for loader equipped with standard tires and dirt bucket.
Dimensions may vary with other types. All dimensions are shown in inches. Respective
metric dimensions are given in millimeters enclosed by parentheses.
• Where applicable, specifications conform to SAE or ISO standards and are subject to
change without notice.
H
G
B
E
A F
24
(610)
48 D C
90 °
35 J
(895)
90 °
H 47.5
(1207)
MC–01202
MC–01174
Backhoe
165 of 176 –4–37– Service Manual
BACKHOE SPECIFICATIONS 923SA (Cont’d)
530, 543, & 553
HYDRAULIC SPECIFICATIONS
Operating Hydraulic Pressure . . . . . . . . . . . . . . . 1575 PSI (10860 kPa)
Cylinder . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Doubleacting
Bore Dia. Rod Dia. Stroke
Boom Cylinder . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.0 (76) 1.5 (38) 15.0 (381)
Arm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.0 (76) 1.5 (38) 15.0 (381)
Bucket Cylinder . . . . . . . . . . . . . . . . . . . . . . . . . . 3.0 (76) 1.5 (38) 15.0 (381)
Swing Cylinder . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.5 (64) 1.25 (32) 5.7 (145)
Stabilizer Cylinder . . . . . . . . . . . . . . . . . . . . . . . . 2.0 (51) 1.0 (25) 19.7 (500)
Fluid Lines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Standard SAE tubelines, hoses & fittings
Valve . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Six section, four way, stack type
OPERATIONAL:
C Digging Depth–Maximum . . . . . . . . . . . . . . . . 93 (2357)
D Digging Depth 2 ft. (0,6 m) Flat Bottom . . . . 92 (2327)
Digging Depth 8 ft. (2,4 m) Flat Bottom . . . . 69 (1752)
E Overall Operating Height Fully Raised . . . . . 103 (2624)
F Loading Height Standard Bucket Position . . 48 (1213)
G Loading Reach Standard Bucket Position . . 52 (1322)
H Reach From Swing Pivot . . . . . . . . . . . . . . . . . 116 (2947)
Swing Pivot to Front Wheels . . . . . . . . . . . . . . . . 93 (917)
Bucket Rotating . . . . . . . . . . . . . . . . . . . . . . . . . . . 140°
Swing Arc . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 180°
Stabilizer Spread (Operating) . . . . . . . . . . . . . . . 35 (895)
J Leveling Angle . . . . . . . . . . . . . . . . . . . . . . . . . . 18.9°
Controls:
Boom, Arm, Bucket & Swing . . . . . . . . . . . . . . Two Hand Levers
Stabilizers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Two Hand Levers
Weight Distribution:
Front . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3094 lbs. (1403 kg)
Rear . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1442 lbs. (654 kg)
Backhoe
166 of 176 –4–38– Service Manual
BACKHOE SPECIFICATIONS 835S • Dimensions are given for loader equipped with standard tires and dirt bucket.
Dimensions may vary with other types. All dimensions are shown in inches. Respective
metric dimensions are given in millimeters enclosed by parentheses.
• Where applicable, specifications conform to SAE or ISO standards and are subject to
change without notice.
E
G
A F
610
1219
D
2438
3048
1829 3048
610 610 MC–01537
0
1219 2438 3658
90 °
90 °
H J
53
(1351)
66
(1674.5)
MC–01174 MC–01538
Backhoe
167 of 176 –4–39– Service Manual
BACKHOE SPECIFICATIONS 835S (Cont’d) 843
HYDRAULIC SPECIFICATIONS
Operating Hydraulic Pressure . . . . . . . . . . . . . 2150 PSI (14824 kPa)
Boom Relief Valve Setting:
At Piston Side of Cylinder . . . . . . . . . . . . . . . 2300 PSI (15858 kPa)
At Rod Side of Cylinder . . . . . . . . . . . . . . . . . 3000 PSI (20684 kPa)
Arm Relief Valve Setting:
At Piston Side of Cylinder . . . . . . . . . . . . . . . 2800 PSI (19306 kPa)
At Rod Side of Cylinder . . . . . . . . . . . . . . . . . 3000 PSI (20685 kPa)
Swing Cylinder Relief Setting . . . . . . . . . . . . . 2150 PSI (14824 kPa)
Cylinder . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Doubleacting
Bore Dia. Rod Dia. Stroke
Boom Cylinder . . . . . . . . . . . . . . . . . . . . . . . . . 3.5 (89) 1.5 (38) 25.7 (653.5)
Arm Cylinder . . . . . . . . . . . . . . . . . . . . . . . . . . 3.5 (89) 1.75 (44.5) 25.7 (653.5)
Bucket Cylinder . . . . . . . . . . . . . . . . . . . . . . . . 3.0 (76) 2.0 (51) 23 (586)
Swing Cylinder . . . . . . . . . . . . . . . . . . . . . . . . . 3.0 (76) 1.5 (38) 8.27 (210)
Stabilizer Cylinder . . . . . . . . . . . . . . . . . . . . . . 2.0 (51) 1.0 (25) 25.4 (500)
TRANSPORT
A Transport Height . . . . . . . . . . . . . . . . . . . . . . 107.5 (2724.5)
Stabilizer Spread (Transport) . . . . . . . . . . . 65 (1674.5)
Ground Clearance . . . . . . . . . . . . . . . . . . . . 3.3 (89.7)
Angle of Approach . . . . . . . . . . . . . . . . . . . . 9.2°
B Overall Length . . . . . . . . . . . . . . . . . . . . . . . . 184 (4674)
Overall Width:
Standard Tires . . . . . . . . . . . . . . . . . . . . . 66 (1674.5)
Flotation . . . . . . . . . . . . . . . . . . . . . . . . . . . 66 (1674.5)
OPERATIONAL
Straight Wall Digging Depth . . . . . . . . . . . . . . . 92 (2328)
C Digging Depth–Maximum . . . . . . . . . . . . . . 135 (3430)
D Digging Depth 2 ft. (0,6 m) Flat Bottom . . 134 (3406)
Digging Depth 8 ft. (2,4 m) Flat Bottom . . 118 (3013)
E Overall Operating Height Fully Raised . . . 162 (4108)
F Loading Height Standard Bucket Position 100 (2557)
G Loading Reach Standard Bucket Position 60 (1532.6)
H Reach From Swing Pivot . . . . . . . . . . . . . . . 167 (4244.8)
Swing Pivot to Front Wheels . . . . . . . . . . . . . . 42 (1064.8)
Bucket Rotation . . . . . . . . . . . . . . . . . . . . . . . . . 200°
Swing Arc . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 180°
Stabilizer Spread (Operating) . . . . . . . . . . . . . 53 (1350.6)
J Leveling Angle . . . . . . . . . . . . . . . . . . . . . . . . 9.2°
Side Shift . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 (486)
Controls:
Boom, Arm, Bucket & Swing . . . . . . . . . . . . Two Hand Levers
Stabilizers . . . . . . . . . . . . . . . . . . . . . . . . . . . Two Hand Levers
WEIGHT
Weight Distribution:
Front . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . N/A
Rear . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . N/A
Backhoe
168 of 176 –4–40– Service Manual
BACKHOE SPECIFICATIONS 835S • Dimensions are given for loader equipped with standard tires and dirt bucket.
(Cont’d) Dimensions may vary with other types. All dimensions are shown in inches. Respective
metric dimensions are given in millimeters enclosed by parentheses.
• Where applicable, specifications conform to SAE or ISO standards and are subject to
change without notice.
E
A G F
610
3048
MC–01572
610 0 610 1829 3048
1219 2438 3658
90 °
90 °
H J
53
(1350)
66 MC–01538
MC–01174 (1674.5)
Backhoe
169 of 176 –4–41– Service Manual
BACKHOE SPECIFICATIONS 835S (Cont’d)
853, 853H, 863 & 873
HYDRAULIC SPECIFICATIONS
Operating Hydraulic Pressure . . . . . . . . . . . . . 2150 PSI (14824 kPa)
Cylinder . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Doubleacting
Bore Dia. Rod Dia. Stroke
Boom Cylinder . . . . . . . . . . . . . . . . . . . . . . . . . 3.5 (89) 1.5 (38) 25.7 (653.5)
Arm Cylinder . . . . . . . . . . . . . . . . . . . . . . . . . . 3.5 (89) 1.75 (44) 25.7 (653.5)
Bucket Cylinder . . . . . . . . . . . . . . . . . . . . . . . . 3.0 (76) 2.0 (51) 23 (586)
Swing Cylinder . . . . . . . . . . . . . . . . . . . . . . . . . 3.0 (76) 1.5 (38) 8.27 (210)
Stabilizer Cylinder . . . . . . . . . . . . . . . . . . . . . . 2.0 (51) 1.0 (25) 25.4 (500)
TRANSPORT
A Transport Height . . . . . . . . . . . . . . . . . . . . . . 108 (2740.3)
Stabilizer Spread (Transport) . . . . . . . . . . . 66 (1674.5)
Ground Clearance . . . . . . . . . . . . . . . . . . . . 4 (103.1)
Angle of Approach . . . . . . . . . . . . . . . . . . . . 10.7°
B Overall Length . . . . . . . . . . . . . . . . . . . . . . . . 182 (4602.2)
Overall Width:
Standard Tires . . . . . . . . . . . . . . . . . . . . . 66 (1674.5)
Flotation . . . . . . . . . . . . . . . . . . . . . . . . . . . 66 (1674.5)
OPERATIONAL
Straight Wall Digging Depth . . . . . . . . . . . . . . . 91 (2320.2)
C Digging Depth–Maximum . . . . . . . . . . . . . . 135 (3421.1)
D Digging Depth 2 ft. (0,6 m) Flat Bottom . . 134 (3398.4)
Digging Depth 8 ft. (2,4 m) Flat Bottom . . 118 (3004.7)
E Overall Operating Height Fully Raised . . . 162 (4116.6)
F Loading Height Standard Bucket Position 100 (2565.0)
G Loading Reach Standard Bucket Position 60 (1532.6)
H Reach From Swing Pivot . . . . . . . . . . . . . . . 167 (4243.4)
Swing Pivot to Front Wheels . . . . . . . . . . . . . . 42 (1070.9)
Bucket Rotation . . . . . . . . . . . . . . . . . . . . . . . . . 200°
Swing Arc . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 180°
Stabilizer Spread (Operating) . . . . . . . . . . . . . 53 (1350.6)
J Leveling Angle . . . . . . . . . . . . . . . . . . . . . . . . 9.2°
Side Shift . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 (490.1)
Controls:
Boom, Arm, Bucket & Swing . . . . . . . . . . . . Two Hand Levers
Stabilizers . . . . . . . . . . . . . . . . . . . . . . . . . . . Two Hand Levers
WEIGHT
Weight Distribution:
Front . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . N/A
Rear . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . N/A
Backhoe
170 of 176 –4–42– Service Manual
BACKHOE SPECIFICATIONS 937S • Dimensions are given for loader equipped with standard tires and dirt bucket.
Dimensions may vary with other types. All dimensions are shown in inches. Respective
metric dimensions are given in millimeters enclosed by parentheses.
• Where applicable, specifications conform to SAE or ISO standards and are subject to
change without notice.
H
205.7
(5525) G
90°
77.4
(1966)
90°
E
205.7
F
(5525)
MC–01139
24.0 (610)
48.0 (1219)
A
11°
19.8 19.5
(503) (495)
22.5°
64.8 (1646)
15.1
78.6 (1996) (384)
87.8 (2230) B
MC–01153
MC–01151
Backhoe
171 of 176 –4–43– Service Manual
BACKHOE SPECIFICATIONS 937S 2400 & 2410
(Cont’d)
OPERATION & PERFORMANCE
Weights
*Operating Weight . . . . . . . . . . . . . . . . . . . 13840 lbs (6283 kg)
937S Backhoe . . . . . . . . . . . . . . . . . . . . . . 3490 lbs (1584 kg)
Lifting Capaicty – Loader . . . . . . . . . . . . . 4000 lbs. (1816 kg)
HYDRAULIC SYSTEMS
Operating Hydraulic Pressure . . . . . . . . . . 2500 PSI (17238 kPa)
Boom Relief Valve Setting:
At Piston Side of Cylinder . . . . . . . . . . . . 2500 PSI (17238 kPa)
At Rod Side of Cylinder . . . . . . . . . . . . . . 3500 PSI (24133 kPa)
Arm Relief Valve Setting:
At Piston Side of Cylinder . . . . . . . . . . . . 3000 PSI (20685 kPa)
At Rod Side of Cylinder . . . . . . . . . . . . . . 3000 PSI (20685 kPa)
Swing Cylinder Relief Setting . . . . . . . . . . 2150 PSI (14824 kPa)
Bucket Relief Valve Setting:
At Piston Side of Cylinder . . . . . . . . . . . . 3000 PSI (20685 kPa)
At Rod Side of Cylinder . . . . . . . . . . . . . . 3500 PSI (24133 kPa)
TRANSPORT
A Transport Height . . . . . . . . . . . . . . . . . . . 141.2 (3586)
Stabilizer Spread (Transport) W/Pads . 78.6 (1996)
Ground Clearance . . . . . . . . . . . . . . . . . 15.1 (384)
Angle of Approach . . . . . . . . . . . . . . . . . 22.5°
B Overall Length (Transport) . . . . . . . . . . 189.4 (4811)
Overall Width . . . . . . . . . . . . . . . . . . . . . . 87.8 (2230)
OPERATIONAL
C Digging Depth–Maximum . . . . . . . . . . . 147.3 (3741)
D Digging Depth 2 ft. (0,6 m) Flat Bottom 146.6 (3724)
Digging Depth 8 ft. (2,4 m) Flat Bottom 135.3 (3437)
E Overall Operating Height Fully Raised 221.0 (4613)
F Loading Height . . . . . . . . . . . . . . . . . . . . 125.4 (3185)
G Loading Reach . . . . . . . . . . . . . . . . . . . . 54.4 (1382)
H Reach From Swing Pivot . . . . . . . . . . . . 205.7 (5225)
Swing Pivot to Front Wheels . . . . . . . . . 50.2 (1275)
Bucket Rotation . . . . . . . . . . . . . . . . . . . . . . 200°
Swing Arc . . . . . . . . . . . . . . . . . . . . . . . . . . . 180°
Stabilizer Spread (Operating) . . . . . . . . . . 64.8 (1646)
Leveling Angle . . . . . . . . . . . . . . . . . . . . . . . 11°
Controls:
Boom, Arm, Bucket & Swing . . . . . . . . . Two Hand Levers
Stabilizers . . . . . . . . . . . . . . . . . . . . . . . . Two Hand Levers
* Machine equipped with 14x17.5 tires, 77’’ Dirt Bucket, ROPS, 937S Backhoe, High Capcity Bucket (P/N 6648081),
full fuel and 175 lbs. (79 kg) operator and fromt counterweight.
Backhoe
172 of 176 –4–44– Service Manual
BUCKET SPECIFICATIONS • All dimensions are shown in inches. Respective metric dimensions are given in
millimeters enclosed by parentheses.
• Where applicable, specifications conform to SAE or ISO standards and are subject to
change without notice.
911 BACKHOE
B–03931
Standard Bucket
913 BACKHOE
B–09032
Backhoe
173 of 176 –4–45– Service Manual
BUCKET SPECIFICATIONS (Cont’d) • All dimensions are shown in inches. Respective metric dimensions are given in
millimeters enclosed by parentheses.
• Where applicable, specifications conform to SAE or ISO standards and are subject to
change without notice.
B–03929
905B BACKHOE
B–03931
Backhoe
174 of 176 –4–46– Service Manual
BUCKET SPECIFICATIONS (Cont’d) • All dimensions are shown in inches. Respective metric dimensions are given in
millimeters enclosed by parentheses.
• Where applicable, specifications conform to SAE or ISO standards and are subject to
change without notice.
MC–01411
607 BACKHOE
709 BACKHOE
Bucket Size Capacity SAE Heaped Shipping Weight
12 in. (305) 1.52 cu. ft. (0,043 cu. m.) 129 lbs. (59 kg)
16 in. (406) 2.11 cu. ft. (0,060 cu. m.) 145 lbs. (66 kg)
20 in. (508) 2.81 cu. ft. (0,080 cu. m.) 160 lbs. (73 kg)
24 in. (610) 3.62 cu. ft. (0,103 cu. m.) 181 lbs. (82 kg)
30 in. (762) 4.60 cu. ft. (0,130 cu. m.) 227 lbs. (103 kg)
8709 BACKHOE
Bucket Size Capacity SAE Heaped Shipping Weight
12 in. (305) 1.52 cu. ft. (0,043 cu. m.) 130 lbs. (59 kg)
16 in. (406) 2.11 cu. ft. (0,060 cu. m.) 145 lbs. (66 kg)
20 in. (508) 2.81 cu. ft. (0,080 cu. m.) 160 lbs. (73 kg)
24 in. (610) 3.62 cu. ft. (0,103 cu. m.) 181 lbs. (82 kg)
30 in. (762) 4.60 cu. ft. (0,130 cu. m.) 227 lbs. (103 kg)
811 BACKHOE
Bucket Size Capacity SAE Heaped Shipping Weight
12 in. (305 mm) 1.52 cu. ft. (0,043 cu. m.) 129 lbs. (59 kg)
16 in. (406 mm) 2.11 cu. ft. (0,059 cu. m) 145 lbs. (66 kg)
20 in. (508 mm) 2.81 cu. ft. (0,078 cu. m.) 160 lbs. (73 kg)
24 in. (610 mm) 3.62 cu. ft. (0,101 cu. m.) 181 lbs. (82 kg)
30 in. (762 mm) 4.60 cu. ft. (0,128 cu. m.) 227 lbs. (103 kg)
36 in. (914 mm) 5.63 cu. ft. (0,159 cu. m.) 253 lbs. (115 kg)
Backhoe
175 of 176 –4–47– Service Manual