Professional Documents
Culture Documents
325b Tassi Modify Wiring in Order To Allow Activation of The Medium Pressure-1
325b Tassi Modify Wiring in Order To Allow Activation of The Medium Pressure-1
Page 1 of 4
Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 325B LN EXCAVATOR 8FN01822
Configuration: 325B & 325B LN Excavators 8FN00001-UP (MACHINE) POWERED BY 3116 Engine
Special Instruction
Modify Wiring in order to Allow Activation of the Medium Pressure
Circuit When the Auxiliary Hydraulic Circuit is in the One-Way Mode
{5734}
Media Number -REHS0557-00Publication Date -01/11/1999Date Updated -09/10/2001
i01223981
Excavator:
320B (PIN: 1XS1)
320B L (PIN: 7JR1; 9WS1; 6LW1)
320B L N (PIN: 3YZ1)
320B N (PIN: 2AS1)
320B S (PIN: 5MS1)
322B L (PIN: 2ES1)
322B L N (PIN: 1ZS1)
325B L (PIN: 6DN1; 4DS1; 5BS1)
325B L N (PIN: 8FN1)
330B L (PIN: 3YR1; 5LR1; 4RS1)
330B L N (PIN: 5LS1)
Introduction
This Special Instruction provides the information that is needed in order to bypass the
auxiliary hydraulic controller which will then allow the switches on the left hand
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/... 8/16/2023
325B & 325B LN Excavators 8FN00001-UP (MACHINE) POWERED B... Page 2 of 4
joystick to directly control the medium pressure circuit when the auxiliary hydraulic
circuit is switched in the one-way mode.
The current configuration of the auxiliary hydraulic circuit that is in the 300B series of
hydraulic excavators does not allow the medium pressure circuit to be used when the
auxiliary hydraulic circuit is switched in the one-way mode. One of the switches on the
left hand joystick that is used to activate the medium pressure circuit is reserved for the
second speed of the hydraulic hammer when the auxiliary hydraulic circuit is switched
in the one-way mode.
Do not perform any rework procedures until you have read the information in this
publication.
Refer to the appropriate Parts Manual for the location of the hardware.
Note: As a result of modifying the circuit, the second speed of the hydraulic hammer
will be disabled when the auxiliary hydraulic circuit is switched in the one-way mode.
The switches on the left hand joystick will now be used for the medium pressure
circuit. The circuit modification will also allow higher current to flow through the
switches. Over a period of time, the sensitivity of the switches to lower currents will be
reduced. It will then be difficult to return to applications that require lower currents.
After modifying the circuit, the 134-5298 Film inside the cab must be replaced by the
179-0898 Film .
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/... 8/16/2023
325B & 325B LN Excavators 8FN00001-UP (MACHINE) POWERED B... Page 3 of 4
Illustration 1 g00654819
The auxiliary hydraulic controller is bypassed in order to allow the switches on the left
hand joystick to directly control the medium pressure circuit. This is accomplished by
performing the following steps.
2. Disconnect the switches of the left hand joystick and the medium pressure
solenoid "MEDIUM PRESSURE SOL R1/R2" from the auxiliary controller.
3. For the switches of the joystick, disconnect the orange wire "547" and the blue
wire "546" from the controller.
4. For the medium pressure solenoid, disconnect the pink wire "A848" and the
yellow wire "A847" from the controller.
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/... 8/16/2023
325B & 325B LN Excavators 8FN00001-UP (MACHINE) POWERED B... Page 4 of 4
Copyright 1993 - 2023 Caterpillar Inc. Wed Aug 16 07:13:33 UTC+0300 2023
All Rights Reserved.
Private Network For SIS Licensees.
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/... 8/16/2023