Professional Documents
Culture Documents
Hardware System
1.Component
Locator
System
Control
Main
2.Safety Range(800mm) Machine
3.Technical instruction of 3 Players
200rpm;
Function Introduction
Press down left-hand button ,wireless mouse connected
1. Start operation the hosts. Press down right-hand button ,connected
control host .
Emergency light switch
Mouse or keyboard
Power supply main switch
change button
power reset
button button
Emergency switch
VGA display
interface
USB connector
Host/ranked
connector
glasses
1.The control panel's power supply and device power plug in the 220V connection
Power
2.Turn on the power switch, on power-up will be red .
power supply
3.Open the power button ,the light will be light up.There are two power button
power switch
on the console. There is a corresponding number of glasses
101/102/103/104/105 power button on the device,must press the power
button. Glasses
power
connection
4.The device will run the emergency stop button clockwise ,or platform does not
rotate.
2. Usage for keyboard and mouse
3. Displayer switch
Switch screen
2.Screen for control
with left buttons.
PC(common)
Or press buttons
on the remote
3 and 4 are backup PC,
controller. Mini remote
Play
If only play some of the machine. We still need to choose the 101.
1.Sub-computers On the
main-computer’s media player
interface, choose one of the
sub-computers addressed 101 /102
/103 /104 /105 and enter the device
management interface, then click
the shutdown button (note: you can
only choose and shut down one
sub-computer very operation).
2.Main-computer
shutdown operation.
2.1 Switch to the operation interface 2
on the main-computer.
2.1
2.2 Switch the mouse and keyboard
to 2
2.3 Shut down the main-computer
just like a normal computer.
2.3
2.2
1. The height of locater is 2.1M and flatwise;The distance between 2 locaters about
5M-6M(can be adjusted according to actual condition).There are 2 locators putting
face to face and connecting by a data line.One is A mode,other is B mode.Once
complete two locators are green or white light that mean the connection is finish.
Green light
Mode A
Data
line
Mode change
button
Power
Power
line
Locater Locater
mode A mode B
Main
Equipments
Connect
Entry the IP address of correspond
extension, click Connect
admin
Entry password admin
2
1 in accordance with the above 2.click on stand up only
steps, open SteamVR, click on the
inverted triangle, and click on the
running room settings.
。
1.Running
room setting
2.Just standing
4.Glass
3 4
3.At right, to rise to the highest bracket ,put away
the glasses, when display “Head-mounted display”If
do not show it all the time .Then put the glasses
from another angle .then slowly back .Such as the
right place .
7
7.Finish
Note:If you press
the Power button
in the games,the
store interface will
10. Matched controller pop up. You need
to press again the
Power button
1 Store interface. 2
System key
Power Charging
button/Applying key port
Indicator light
1.If the machine don’t be used for a long time, the indicator light will not light up. In this case, you should press the
power button to restart.
2.If the indicator light is flashing red, it representatives the battery doesn’t have enough power, needing to be charged.
Flashing white means the battery are fully charged.
3.If the machine is connected, the light will flash green or white.4.Flashing blue means is matching, not connecting yet.
3 4
5
5.The controller has been
successfully matched.
11. Fixed bracket
safety belt
Lift button
12.Attention:
12.1 If the controller is full of power, can be used continuously for about 8 hours,
please charge in time.
12.2 Only the first game has ranked, second game doesn't support ranking.
12.3 Before playing the game, please adjust the height of the fixed bracket, and
fasten the safety belt.
12.4 If the game stops in midway, you need to reset the platform position, otherwise
it will be a large rotation when restarting
12.5 Locator can not be exposed to strong light.Should better change the strong light
into weak light.
12.6 Locator can not be hided
12.7 Once the location of the locator is determined, please do not move. Otherwise
need to reset the room size (see Step 9).
12.8 When the machine is on, please keep distance with it.