Professional Documents
Culture Documents
Capacity 175
Staging 18
Dia 8.05
Height 4.05
Gross Volume(KL) 206.13
Eff. Volume (KL) 175.23
Free Board Height (min)(m) 0.44
Eff. Ht 3.44
Dead Ht 0.162
Dead Load 3
Live Load 178
SBC 8
GONAHA
DIH
GONHAT
AL
SURVEY, DESIGN, PREPARATION OF DPR, CONSTRUCTION
COMMISSIONING AND O & M FOR 10 YEARS FOR VARIOUS
Project RURAL WATER SUPPLY PROJECT IN THE STATE OF UTTAR
PRADESH FOR DIVISION-SIDDHARTHA NAGAR
Staging Height = 18 m
2 PERMISSIBLE STRESSES:
Allowable stress as per IS:3370 relating to resistance to cracking
Ref Table 1 of Allowable direct tensile stress in concrete sat = 1.5 N/mm2
IS:3370 (Part-
2) Allowable bending tensile stress in concrete σbt = 2.0 N/mm2
Ref Table 4 of Allowable stress in steel under direct tension, bending & shear = s st = 130 N/mm2
IS:3370 (Part-
2) Allowable stress in steel under direct compression = s st = 140 N/mm2
Ref Table 2 of Allowable direct compressive stress in concrete σcc = 8.0 N/mm2
IS:3370 (Part-
2) Allowable bending compressive stress in concrete σcbc = 10.0 N/mm2
3 DIMENSIONS OF TANK
Internal diameter of the tank, D = 8.05 m
No of Levels of Bracing = 4
4 VOLUME CALCULATION:
The Volume of the Intze Tank is given by the following components:
Ly/Lx 2.000
Design of Slab
4025 mm
Shorter span (clear dimension)
4025 mm
Longer span (clear dimension)
42.65 kN/m2
Live load
400 mm
Width of support
30 N/mm2
Grade of concrete (fck)
500 N/mm2
Grade of steel (fy)
Xumax/d 0.456
bd2
1.Thickness of slab:
Span/depth 26
Span/depth ~ 31 31.2
20 mm
Clear cover
130 mm
Required effective depth
180 mm
Adopt thickness of slab is
160 mm
Effective depth of slab (d)
2.Effective span:
Least of followig
4425 mm
C/C of support
4185 mm
Clear span + d
4185 mm
For shorter span (lx)
9.00 kN/m2
Design dead load (W)/Sqm
42.65 kN/m2
Design Live load (W)/Sqm
∞x +ve 0.049
∞x +ve 0.024
For shorter span For Longer span
Sl.No Design moments (KN.m)
7.Reinforcements:
240 mm2
ForLonger span
fs value 46.3
< 0
The slab is uncracked section
107 mm
Distance of point from surface of bar (acr)
Load Calculation:
Using Coefficient of bending and torsional moment (Table-3, IS4995 (Part - 2))
Shear Force at section of max. torsion at an angle 9.53 deg from column support =
Depth Check OK
Clear cover = 25 mm
Reinf. Check OK
Design at Mid-Span
Depth Check OK
Reinf. Check OK
Depth Check OK
15 STABILITY CHECK:
Vertical Load due to Container = 30.0 kN
Overturning Check-
FOS = 7.2
OK
Sliding Check-
Stabilizing Force (Dead Weight of Empty Tank * Friction Coefficient * 0.9) = 1204.6 kN
FOS = 0.62
CHECK
WIND ANALYSIS
Calculation of Wind Load
Basic Wind Speed considered (Vb) = 47 m/s
Design Wind Speed is given by Vz = K1xK2xK3xVb
Risk Coefficient (K1) = 1.07
Terrain, Height and structure size Coefficient (K 2) = 1.070
(for Terrain Catergory = 2, Class-B and Height = 1.07m)
Topography Factor (K3) = 1
Importance Factor for cyclonic Region (K4) = 1
Design Wind Speed is given by Vz = 47x1.07x1.07x1 53.81 m/s
Design Wind Pressure, Pz = 0.6x53.81^2 1.74 kN/m2
For all circular members in plan consider shape factor as 0.7 0.7
Height upto top = 22.04 m
Outer diameter of tank (D) = 8.05 m
Diameter of staging (D1) = 8.05 m
Cylindrical container + top dome container height= 4.04 m
Container height (H) = 4.04 m
Uplift Force on Roof & Bottom Per Sqm
As per IS 875 Part-3 (Table No. 20 Cl. No. 7.3.3.8)
H= 4.04 m
Z= 22.04 m
(Z/H-1)= 4.46
Cpe for bottom = -0.6
Cpi = 0
Uplift force on roof = (Cpe-Cpi) x A x pz ABS((-0.75-0)x3.14/4x8.05^2x1.737) 66.30 kN
Moment due to eccentricity = 0.1*D = 0.1x8.05x66.3 53 kN-m
Uplift force on bottom=(Cpe-Cpi) x A x pz ABS((-0.6-0)x3.14/4x8.05x8.05x1.737) 53.04 kN
Moment due to eccentricity = 0.1*D = 0.1x8.05x53.04 43 kN-m
Horizontal Force on Tank
H/D = 4.042/8.05 0.5
Vz x D (Refer table 25 of IS 875 part 3) = 8.05x53.81 433.1705
Vz x D > 6
Exposed area of Top Dome & Cylindrical Portion, Ae = D x H 8.05x4.042 32.54 m2
Cf (Ref table 25 IS 875 part 3) = 0.7
Wind load on Top slab & Cylindrical Portion = 0.7x32.54x1.737 39.57 kN
Wind Load For Staging
Refer cl. No 6.3, 6.3.3, 6.3.3.3 and Table 28 of IS 875 part 3
Risk Coefficient (K1) = 1.07
Terrain, Height and structure size Coefficient (K 2) =
k2 for different height (m)
up to 10 m 1
10 to 15 m 1.05
15 to 20 m 1.07
20 to 30 m 1.12
Topography Factor (K3) = 1.00
Importance Factor for cyclonic Region (K4) = 1.00
Design wind speed Vb =V xk1xk2xk3
up to 10 m 47x1.07x1x1x1 50.29 m/s
10 to 15 m 47x1.07x1.05x1x1 52.80 m/s
15 to 20 m 47x1.07x1.07x1x1 53.81 m/s
20 to 30 m 47x1.07x1.12x1x1 56.32 m/s
Intensity of wind pressure (pd) =0.6 x Vb 2
up to 10 m 0.6*50.29^2/1000 1.52 kN/m2
10 to 15 m 0.6*52.8^2/1000 1.67 kN/m2
15 to 20 m 0.6*53.81^2/1000 1.74 kN/m2
20 to 30 m 0.6*56.32^2/1000 1.90 kN/m2
Due to Container
Force Height From Bottom of Raft to C.G. Of Body Moment
39.57 kN 19.72 m 780.32 kN-m
Due to Column
Length of
Load on Column No of Columns Force Distance from Raft Moment
Column
0.44 kN/m 8 10 35.20 kN 8 281.60 kN-m
0.48 kN/m 8 5 19.20 kN 15.5 297.60 kN-m
Total Bending
Total Force = 66.40 kN 813.20 kN-m
Moment =
Due to Bracing
Hydrodynamic Pressure:
Convective Mode:
Time period of convective mode, T c = 2π√(mc/Kc) = 3.05 sec
For Medium Soil and 5% Damping, Corresponding (Sa/g) = 0.45
Design Horizontal Seismic Coefficient, (A h)c = 0.0320
Lateral Force:
Total Base Shear, V = (Vi2 + Vc2)0.5 = 128.52 KN
Total Moment, M = (Mi + Mc ) =
2 2 0.5 2880.15 kN-m
Hydrodynamic Pressure:
This maximum hydrodynamic pressure is about 8.56% of hydrostatic pressure under working condition at base (ρgh =
33.7464 kN/m2). Container of tank is designed for hydrotest condition. When earthquake forces are considered,
permissible stresses are increased by 33%. Hence, hydrodynamic pressure in this case does not affect container
design.
77.11 kN
Lateral Force, V = Ah ms g =
Calculations of tangential and radial moments have been done as per the procedure explained in IS
11089 - 1984 Practice for Design and Construction of Ring Foundation
Design at Mid-Span
Maximum positive B.M. at Mid-Span section ( M ) = 125.12 kN-m
Tortional Moment = 0.00 kN-m
Bending Moment due to Tortional Moment = 0.00 kN-m
Total Maximum Positive BM at Mid-Span = 125.12 kN-m
Depth required from B.M. consideration = 237.6 mm
Depth Check OK
Area of Steel required = 364 mm2
Minimum Percentage of steel required= 0.24%
Area of mimimum steel required = 520 mm2
Diameter of bar to be considered= 16 mm
No of 16 mm dia bars 3 Nos
Diameter of bar to be considered= 16 mm
No of 16 mm dia bars 2 Nos
Area of steel provided= 1005 mm2
Reinf. Check OK
Provide 3 bars of 16mm dia & 2 bars of 16 mm dia at Top
Landing 1= 0.45 m
Going = 2.556 m
Landing 2 = 0.45 m
Riser = 180 mm
Tread = 250 mm
16.77
12 12.000 m
0.16
a L1 = 0.45 m L2 = 2.556 m L3 = 0.45 m b
Ra Rb
Ra = 92.73/(0.45+2.556+0.45) 26.83 KN
Reaction at b = (12x0.45+16.77x2.556+12x0.45)-26.83 26.83 KN
Maximum BM Occurs at the point 'x' where SF is Zero or Changes its sign.
Point of Maximum Moment = 1.73 m
OK
Fs = 271.4 N/mm2
OK
100 Ast
Percentage of Steel provided bd
0.42%
Permisible Shear stress in concrete for the provided % of steel tc = 0.35 N/mm2
OK
100 Ast
Percentage of Steel provided bd
0.58%
Permisible Shear stress in concrete for the provided % of steel tc = 0.35 N/mm2
Design of Column
Top Reinforcement
Requrment area of steel at support as per Staad = = 695.00 mm2
Provide dia of bar = 16 mm
Provide no of Bar = 3 Nos
Extra Reinforcement L/4 From support 12 mm
1 Nos
Provide area of steel = 715.92 mm2
Bottom Reinforcement
Requrment area of steel at middle span as per Staad = = 622.00 mm2
Provide dia of bar = 16 mm
Provide no of Bar = 2 Nos
Extra Reinforcement after L/6 From support 12 mm
2 Nos
Provide area of steel = 628.00 mm2
Provide #8@175c/c
Bracing B-2
Top Reinforcement
Requrment area of steel at support as per Staad = = 513.00 mm2
Provide dia of bar = 16 mm
Provide no of Bar = 2 Nos
Provide dia of bar = 12 mm
Provide no of Bar = 1 Nos
Provide area of steel = 514.96 mm2
Bottom Reinforcement
Requrment area of steel at middle span as per Staad = = 435.00 mm2
Provide dia of bar = 16 mm
Provide no of Bar = 2 Nos
Provide dia of bar = 12 mm
Provide no of Bar = 1 Nos
Provide area of steel = 514.96 mm2
Provide #8@170c/c
Plinth level beam
Top Reinforcement
Requrment area of steel at support as per Staad = = 680.00 mm2
Provide dia of bar = 16 mm
Provide no of Bar = 2 Nos
Provide dia of bar = 12 mm
Provide no of Bar = 2 Nos
Provide area of steel = 628.00 mm2
Bottom Reinforcement
Requrment area of steel at middle span as per Staad = = 605.00 mm2
Provide dia of bar = 16 mm
Provide no of Bar = 2 Nos
Provide dia of bar = 12 mm
Provide no of Bar = 2 Nos
Provide area of steel = 628.00 mm2
Provide #8@170c/c
STAAD SPACE
START JOB INFORMATION
ENGINEER DATE 25/06/2023
JOB NAME BANSI 175 KL Radius Angle Number of column
END JOB INFORMATION 4.025 45.00 8
INPUT WIDTH 79
UNIT METER KN Column Node at Footing
JOINT COORDINATES Node X Y Z
1 4.025 -3 0 1 4.025 -3 0
2 2.846 -3 -2.846 2 2.846 -3 -2.846
3 0 -3 -4.025 3 0.000 -3 -4.025
4 -2.846 -3 -2.846 4 -2.846 -3 -2.846
5 -4.025 -3 0 5 -4.025 -3 0
6 -2.846 -3 2.846 6 -2.846 -3 2.846
7 0 -3 4.025 7 0.000 -3 4.025
8 2.846 -3 2.846 8 2.846 -3 2.846
***** 0 -3 0 ***** 0.000 -3 0
***** 0 -3 0 ***** 0.000 -3 0
Column Node Footing to plinth beam
9 4.025 -0.225 0 9 4.025 -0.225 0.000
10 2.846 -0.225 -2.846 10 2.846 -0.225 -2.846
11 0 -0.225 -4.025 11 0.000 -0.225 -4.025
12 -2.846 -0.225 -2.846 12 -2.846 -0.225 -2.846
13 -4.025 -0.225 0 13 -4.025 -0.225 0.000
14 -2.846 -0.225 2.846 14 -2.846 -0.225 2.846
15 0 -0.225 4.025 15 0.000 -0.225 4.025
16 2.846 -0.225 2.846 16 2.846 -0.225 2.846
**** 0 -0.225 0 **** 0.000 -0.225 0.000
**** 0 -0.225 0 **** 0.000 -0.225 0.000
Column Node Plinth beam to first bracing bracing
17 4.025 2.725 0 17 4.025 2.725 0.000
18 2.846 2.725 -2.846 18 2.846 2.725 -2.846
19 0 2.725 -4.025 19 0.000 2.725 -4.025
20 -2.846 2.725 -2.846 20 -2.846 2.725 -2.846
21 -4.025 2.725 0 21 -4.025 2.725 0.000
22 -2.846 2.725 2.846 22 -2.846 2.725 2.846
23 0 2.725 4.025 23 0.000 2.725 4.025
24 2.846 2.725 2.846 24 2.846 2.725 2.846
**** 0 2.725 0 **** 0.000 2.725 0.000
**** 0 2.725 0 **** 0.000 2.725 0.000
Column Node First bracing to Second Bracing
25 4.025 6.4 0 25 4.025 6.4 0.000
26 2.846 6.4 -2.846 26 2.846 6.4 -2.846
27 0 6.4 -4.025 27 0.000 6.4 -4.025
28 -2.846 6.4 -2.846 28 -2.846 6.4 -2.846
29 -4.025 6.4 0 29 -4.025 6.4 0.000
30 -2.846 6.4 2.846 30 -2.846 6.4 2.846
31 0 6.4 4.025 31 0.000 6.4 4.025
32 2.846 6.4 2.846 32 2.846 6.4 2.846
**** 0 6.4 0 **** 0.000 6.4 0.000
**** 0 6.4 0 **** 0.000 6.4 0.000
Column Node Second bracing toThird Bracing
33 4.025 10.075 0 33 4.025 10.075 0.000
34 2.846 10.075 -2.846 34 2.846 10.075 -2.846
35 0 10.075 -4.025 35 0.000 10.075 -4.025
36 -2.846 10.075 -2.846 36 -2.846 10.075 -2.846
37 -4.025 10.075 0 37 -4.025 10.075 0.000
38 -2.846 10.075 2.846 38 -2.846 10.075 2.846
39 0 10.075 4.025 39 0.000 10.075 4.025
40 2.846 10.075 2.846 40 2.846 10.075 2.846
**** 0 10.075 0 **** 0.000 10.075 0.000
**** 0 10.075 0 **** 0.000 10.075 0.000
Column Node Third bracing to top ring beam
41 4.025 13.925 0 41 4.025 13.925 0.000
42 2.846 13.925 -2.846 42 2.846 13.925 -2.846
43 0 13.925 -4.025 43 0.000 13.925 -4.025
44 -2.846 13.925 -2.846 44 -2.846 13.925 -2.846
45 -4.025 13.925 0 45 -4.025 13.925 0.000
46 -2.846 13.925 2.846 46 -2.846 13.925 2.846
47 0 13.925 4.025 47 0.000 13.925 4.025
48 2.846 13.925 2.846 48 2.846 13.925 2.846
**** 0 13.925 0 **** 0.000 13.925 0.000
**** 0 13.925 0 **** 0.000 13.925 0.000
Node of stair
49 4.925 -0.225 0 49 4.925 -0.225 0
50 3.483 2 -3.483 50 3.483 2 -3.483
51 0 4 -4.925 51 0.000 4 -4.925
52 -3.483 6 -3.483 52 -3.483 6 -3.483
53 -4.925 8 0 53 -4.925 8 0
54 -3.483 10 3.483 54 -3.483 10 3.483
55 4.925 12 0 55 4.925 12 0
56 3.483 0 -3.483 56 3.483 0 -3.483
For (B2-Middle Ring Beam & Conical Dome) For (B3-Bottom Ring Beam & Bottom Spherical Dome)
radius of Beam at center = Err:509 m Width of ring beam = Err:509 m
Width of ring beam = Err:509 m Depth of ring beam = Err:509 m
Depth of ring beam = Err:509 m Thk of bottom dome = Err:508 m
Hoop tension at top of Conical wall = 0.00 kN Radius of bottom dome R0= Err:509 m
Hoop tension at bottom Conical wall = 0.00 kN Central rise of dome = Err:509 m
Dia of conical wall at top = Err:509 m Theta θ = Err:509
Thk of conical wall = Err:509 m cos theta = Err:509
Dia of conical wall at bottom = Err:509 m sin theta = Err:509
Total vertical load on middle ring beam = Err:509 kN/m Net force = Err:509 kN/m
angle Φ = Err:509 degree
Vertical load on conical wall at bottom = Err:509 kN/m
inclined length of conical wall = 0.00 m
(1) Effects of Continuity at the Junction of Top Dome, B1-Top Ring Beam & Cylindrical Wall:
(a) Membrane deformations and stiffnesses:
Solve Eq 1 and 2
ψ = net rotation = Err:509
δ = net displacement = Err:509
Member M (kN-m)
Top Dome Err:509 Err:509
Beam B1 Err:509 Err:509
Cylindrical Wall Err:509 Err:509
Sum Err:509 Err:509
Member H (kN)
Top slab Err:509 Err:509
Beam B1 Err:509 Err:509
Cylindrical Wall Err:509 Err:509
Sum Err:509 Err:509
Member Net hoop tension(kN/m)
Top slab Err:509 Err:509
Beam B1 Err:509 Err:509
Cylindrical Wall Err:509 Err:509
(2) Effects of Continuity at the Junction of Cylindrical Wall, B2-Middle Ring Beam & Conical Dome:
(a) Membrane Deformations and Stiffnesses
(i) B2-Middle Ring Beam
Width (m) = Err:509
Depth (m) = Err:509
Radial thrust to cause unit outward deflection, H(kN/m) = Err:509 H = Ebd/R2
Radial moment to cause unit rotation of beam, M (kN-m/m) = Err:509 M = Ebd3/12R2
(ii) Conical Dome:
Hoop tension,top,T2(kN) = 0.00
Hoop tension,bottom,T20(kN) = 0.00
Outward defln δ,top(m) = Err:509 =(T2 X Dtop)/(E X t X 2)
Outward defln δ0,bottom(m)= Err:509 =(T20 X Dbott)/(E X t X 2)
Meridional thrust,T1(kN) = Err:509 T2Top=W1 X sec Φ
Slope at top edges,ψ(rad.) = Err:509 Ψ = (-tanΦ/Et)*(2T2+T1)
Meridional thrust,T10(kN)= Err:509 T2Bot=W2 X secΦ
Slope,bottom edges,ψ= Err:509 Ψ = (-tanΦ/Et)*(2T2(bot)+T1(bot))
Inclined length of conical wall, l (m) = 0.00
L' (m) = Err:509 L' = RcosecΦ
L (m) = Err:509 L = l+L'
Δ= Err:509 Δ = (12*cot2Φ/t2)0.25
Solve Eq 3 and 4
ψ = net rotation = Err:509
δ = net displacement = Err:509
Member M (kN-m)
Wall Err:509 Err:509
Beam B3 Err:509 Err:509
Coni.dome Err:509 Err:509
Member H (kN)
Wall Err:509 Err:509
Beam B3 Err:509 Err:509
Coni.dome Err:509 Err:509
Member Net hoop tens(kN/m)
Wall Err:509 Err:509
Beam B3 Err:509 Err:509
Coni.dome Err:509 Err:509
(3) Effects of Continuity at the Junction of Conical Dome, B3-Bottom Ring Beam & Bottom Spherical Dome:
(a) Membrane Deformations and Stiffnesses
(i) B3-Bottom Ring Beam
b (m) = Err:509
d (m) = Err:509
Radius of shaft,R0 (m) = 4.03
Moment stiffness, M (N-m/radian) = Err:509
M = (bd3E)/(3R02)
Corresponding H (N/radian) = Err:509
H = (bd2E)/(2R02)
Thrust stiffness H (N/unit movement) = Err:509
H = (bdE)/(R02)
Corresponding M (N-m/unit movement) = Err:509
M = (bd2E)/(2R02)
(ii) Spherical Bottom Dome
Thickness t2 (m) = Err:508
Radius of Dome R0(m) = Err:509
UDL due to s.wt., p (kN/m2) = Err:508
UDL due to wt of water above crown level, p' (kN/m 2) = Err:509
Slope,ψ = Err:508
((2wR0Sinθ)/(Et2))-((wR02Sinθ)/(Et2)
δ= Err:509 ((pR2sinθ)/(Et2))((1/(1+cosθ))-cosθ)]-(p'R2sinθ)/(2Et2)+(wR3sinθ)/(6Et2(1+cosθ)))
α2 = Err:509 (2cosθ+cosθ-3)
(3(R0/t2))0.25
α22 = Err:509
α =
2
3
Err:509
K2 = Err:509 1-((1/2α2) cotθ)
Moment stiffness M (N-m/m/rad) = Err:509
((E R2 t)/(4 α23)) ((K2 + (1/K2))
Corresponding H (N/m/radian) = Err:509
(E t2)/((2 α22 K2 Sinθ
Thrust stiffness H/unit displacement = Err:509
(E t2)/((α2 R0 K2 Sin2θ)
Corresponding moment M (N-m/m unit displ.) = Err:509
(E t2)/((2 α2 R0 K2 Sinθ)
Solve Eq 5 and 6
ψ = net rotation = Err:509
δ = net displacement = Err:509
Member M (kN-m)
Conical dome Err:509 Err:509
Beam B3 Err:509 Err:509
Bottom dome Err:509 Err:509
Member H (kN)
Conical dome Err:509 Err:509
Beam B3 Err:509 Err:509
Bottom dome Err:509 Err:509
Member Net hoop tension(kN/m)
Conical dome Err:509 Err:509
Beam B3 Negligible
Bottom dome Err:509 Err:509
BZ STRUCTURE CONSULTANT
Landing 1= 0.45 m
Going = 2.556 m
Landing 2 = 0.45 m
Riser = 170 mm
Tread = 250 mm
15.99
11.625 11.625
Ra = 88.7/(0.45+2.556+0.45) 25.67 KN
Reaction at b = (11.625x0.45+15.99x2.556+11.625x0.45)-25.67 25.66 KN
Maximum BM Occurs at the point 'x' where SF is Zero or Changes its sign.
Point of Maximum Moment = 1.73 m
OK
Fs = 250.7 N/mm2
OK