Professional Documents
Culture Documents
CRT4231
DEH-1100MP/XN/UC
CD RECEIVER
DEH-1100MP /XN/UC
DEH-1150MPG/XN/ES
DEH-1150MP/XN/ES
DEH-1150MPG/XN/ES1
DEH-1150MP/X1N/EC
DEH-1190MP/XN/ID
This service manual should be used together with the following manual(s):
Model No. Order No. Mech.Module Remarks
CX-3195 CRT3815 S10.5COMP2 CD Mech. Module : Circuit Descriptions, Mech. Descriptions, Disassembly
SAFETY INFORMATION
CAUTION
A This service manual is intended for qualified service technicians; it is not meant for the casual do-it-yourselfer.
Qualified technicians have the necessary test equipment and tools, and have been trained to properly and safety repair
complex products such as those covered by this manual.
Improperly performed repairs can adversely affect the safety and reliability of the product and may void the warranty.
If you are not qualified to perform the repair of this product properly and safety, you should not risk trying to do so
and refer the repair to a qualified service technician.
WARNING
This product contains certain electrical parts contain chemicals which are known to the State of
California to cause cancer, birth defects or other reproductive harm.
Health & Safety Code Section 25249.6 - Proposition 65
B
Where in a manufacturer’s service documentation, for example in circuit diagrams or lists
of components, a symbol is used to indicate that a specific component shall be replaced only
by the component specified in that documentation for safety reasons, the following symbol shall
be used:
Caution:
1. During repair or tests, minimum distance of 13 cm from the focus lens must be kept.
2. During repair or tests, do not view laser beam for 10 seconds or longer.
CAUTION:
USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF PROCEDURES OTHER THAN THOSE
SPECIFIED HEREIN MAY RESULT IN HAZARDOUS RADIATION EXPOSURE.
D CAUTION
CLASS 1M INVISIBLE LASER RADIATION WHEN OPEN. DO NOT VIEW DIRECTLY WITH OPTICAL INSTRUMENTS
WARNING!
The AEL (accessible emission level )of the laser power output is less than CLASS 1
but the laser component is capable of emitting radiation exceeding the limit for
CLASS 1.
A specially instructed person should do servicing operation of the apparatus.
E
DEH-1100MP/XN/UC
2
1 2 3 4
5 6 7 8
CAUTION
A
Danger of explosion if battery is incorrectly replaced.
Replaced only with the same or equivalent type recommended by the manufacture.
Discord used batteries according to the manufacture's instructions.
DEH-1100MP/XN/UC
5 6 7 8
3
1 2 3 4
Please follow the specified safety methods when modification(addition/change of parts) is required due to interferences such as
radio/TV interference and foreign noise.
When you solder while repairing, please be sure that there are no cold solder and other debris.
Soldering should be finished with the proper quantity. (Refer to the example)
Please be sure that all screws are fastened, and that there are no loose screws.
Please be sure that all connectors are inserted, and that there are no imperfect insertion.
6 Make sure the wiring cables are set to their original state.
Please replace the wiring and cables to the original state after repairs.
C In addition, be sure that there are no pinched wires, etc.
7 Make sure screws and soldering scraps do not remain inside the product.
Please check that neither solder debris nor screws remain inside the product.
8 There should be no semi-broken wires, scratches, melting, etc. on the coating of the power cord.
Damaged power cords may lead to fire accidents, so please be sure that there are no damages.
If you find a damaged power cord, please exchange it with a suitable one.
When spark traces or similar marks are found on the power supply plug, please check the connection and advise on secure
connections and suitable usage. Please exchange the power cord if necessary.
D a Safe environment should be secured during servicing.
When you perform repairs, please pay attention to static electricity, furniture, household articles, etc. in order to prevent injuries.
Please pay attention to your surroundings and repair safely.
2. Adjustments
To keep the original performance of the products, optimum adjustments and confirmation of characteristics within specification.
Adjustments should be performed in accordance with the procedures/instructions described in this manual.
4. Cleaning
For parts that require cleaning, such as optical pickups, tape deck heads, lenses and mirrors used in projection monitors, proper
cleaning should be performed to restore their performances.
DEH-1100MP/XN/UC
4
1 2 3 4
5 6 7 8
CONTENTS
SAFETY INFORMATION .....................................................................................................................................2
1. SERVICE PRECAUTIONS................................................................................................................................6
1.1 SERVICE PRECAUTIONS .........................................................................................................................6 A
1.2 NOTES ON SOLDERING ...........................................................................................................................6
2. SPECIFICATIONS.............................................................................................................................................7
2.1 SPECIFICATIONS ......................................................................................................................................7
2.2 DISC/CONTENT FORMAT .........................................................................................................................9
2.3 PANEL FACILITIES.....................................................................................................................................9
2.4 CONNECTION DIAGRAM........................................................................................................................11
3. BASIC ITEMS FOR SERVICE ........................................................................................................................12
3.1 CHECK POINTS AFTER SERVICING .....................................................................................................12
3.2 PCB LOCATIONS .....................................................................................................................................13
3.3 JIGS LIST .................................................................................................................................................14
3.4 CLEANING ...............................................................................................................................................14
4. BLOCK DIAGRAM ..........................................................................................................................................16 B
5. DIAGNOSIS ....................................................................................................................................................19
5.1 OPERATIONAL FLOWCHART .................................................................................................................19
5.2 ERROR CODE LIST.................................................................................................................................20
5.3 CONNECTOR FUNCTION DESCRIPTION .............................................................................................21
6. SERVICE MODE.............................................................................................................................................22
6.1 DISPLAY TEST MODE .............................................................................................................................22
6.2 CD TEST MODE.......................................................................................................................................23
7. DISASSEMBLY ...............................................................................................................................................24
8. EACH SETTING AND ADJUSTMENT ............................................................................................................27
8.1 CD ADJUSTMENT ...................................................................................................................................27
8.2 CHECKING THE GRATING AFTER CHANGING THE PICKUP UNIT ....................................................28
C
9. EXPLODED VIEWS AND PARTS LIST ..........................................................................................................30
9.1 PACKING ..................................................................................................................................................30
9.2 EXTERIOR(1) ...........................................................................................................................................32
9.3 EXTERIOR(2) ...........................................................................................................................................34
9.4 CD MECHANISM MODULE .....................................................................................................................36
10. SCHEMATIC DIAGRAM................................................................................................................................38
10.1 TUNER AMP UNIT(GUIDE PAGE) .........................................................................................................38
10.2 KEYBOARD UNIT ..................................................................................................................................44
10.3 CD MECHANISM MODULE(GUIDE PAGE) ...........................................................................................46
10.4 WAVEFORMS.........................................................................................................................................52
11. PCB CONNECTION DIAGRAM ....................................................................................................................54
11.1 TUNER AMP UNIT .................................................................................................................................54 D
11.2 KEYBOARD UNIT ..................................................................................................................................58
11.3 CD CORE UNIT(S10.5COMP2) .............................................................................................................60
12. ELECTRICAL PARTS LIST ...........................................................................................................................62
DEH-1100MP/XN/UC
5 6 7 8
5
1 2 3 4
1. SERVICE PRECAUTIONS
1.1 SERVICE PRECAUTIONS
A
For environmental protection, lead-free solder is used on the printed circuit boards mounted in this unit.
Be sure to use lead-free solder and a soldering iron that can meet specifications for use with lead-free solders for repairs
accompanied by reworking of soldering.
Compared with conventional eutectic solders, lead-free solders have higher melting points, by approximately 40 C.
D Therefore, for lead-free soldering, the tip temperature of a soldering iron must be set to around 373 C in general, although
the temperature depends on the heat capacity of the PC board on which reworking is required and the weight of the tip of
the soldering iron.
Compared with eutectic solders, lead-free solders have higher bond strengths but slower wetting times and higher melting
temperatures (hard to melt/easy to harden).
DEH-1100MP/XN/UC
6
1 2 3 4
5 6 7 8
2. SPECIFICATIONS
2.1 SPECIFICATIONS
A
DEH-1100MP/XN/UC
General FM tuner
Power source..........................14.4 V DC (10.8 V to 15.1 V Frequency range................... 87.9 MHz to 107.9 MHz
allowable) Usable sensitivity.................. 11 dBf (0.7 μV/75 , mono,
Grounding system.................Negative type S/N: 30 dB)
Max. current consumption Signal-to-noise ratio............. 72 dB (IHF-A network)
...............................................10.0 A
Backup current ....................... 2 mA or less AM tuner B
Frequency range................... 530 kHz to 1 710 kHz
Dimensions (W × H × D): Usable sensitivity.................. 25 μV (S/N: 20 dB)
DIN Signal-to-noise ratio............. 62 dB (IHF-A network)
Chassis .................. 178 mm × 50 mm × 162
mm CEA2006 Specifications
(7 in. × 2 in. × 6-3/8 in.)
Nose ....................... 188 mm × 58 mm × 15 mm
(7-3/8 in.× 2-1/4 in.× 5/8 in.)
D
Chassis .................. 178 mm × 50 mm × 162
mm
(7 in.× 2 in.× 6-3/8 in.) C
Power output ......................... 14 W RMS × 4 Channels (4
Nose ....................... 170 mm × 48 mm × 15 mm and 1 % THD+N)
(6-3/4 in.× 1-7/8 in.× 5/8 in.) S/N ratio .................................. 91 dBA (reference: 1 W into
Weight .................................... 1.3 kg (2.9 lbs) 4 )
Audio
Note
Maximum power output ....... 50 W × 4
Continuous power output ... 22 W × 4 (50 Hz to 15 000 Specifications and the design are subject to mod-
Hz, 5% THD, 4 load, both ifications without notice due to improvements.
channels driven)
Load impedance .................... 4 (4 to 8 allowable)
Preout max output level ....... 2.0 V D
Tone controls:
Bass
Frequency.............. 100 Hz
Gain .........................±13 dB
Mid
Frequency............... 1 kHz
Gain .......................... ±12 dB
Treble
Frequency............... 10 kHz
Gain ........................... ±12 dB
E
CD player
System ..................................... Compact disc audio system
Usable discs .......................... Compact disc
Signal-to-noise ratio............ 94 dB (1 kHz) (IHF-A net-
work)
Number of channels ............ 2 (stereo)
WMA decoding format ....... Ver. 7, 7.1, 8, 9, 10, 11 (2ch
audio)
(Windows Media Player)
MP3 decoding format ..........MPEG-1 & 2 Audio Layer 3
WAV signal format ................ Linear PCM & MS ADPCM
F
DEH-1100MP/XN/UC
5 6 7 8
7
1 2 3 4
CD player
System ..................................... Compact disc audio system
Usable discs .......................... Compact disc
Signal-to-noise ratio............ 94 dB (1 kHz) (IEC-A net-
work)
Number of channels ............ 2 (stereo)
E WMA decoding format ....... Ver. 7, 7.1, 8, 9, 10, 11 (2ch
audio)
(Windows Media Player)
MP3 decoding format ..........MPEG-1 & 2 Audio Layer 3
WAV signal format ................ Linear PCM & MS ADPCM
FM tuner
Frequency range................... 87.5 MHz to 108.0 MHz
Usable sensitivity.................. 11 dBf (0.7 μV/75 , mono,
S/N: 30 dB)
DEH-1100MP/XN/UC
8
1 2 3 4
5 6 7 8
c EQ button
Press to select various equalizer curves.
dc b a 98 7 Press and hold to turn loudness on or off.
1 FUNCTION button d BAND button
Press to recall the function menu when op- Press to select among three FM bands and
erating a source. one AM band and to cancel control modes C
DEH-1100MP/XN/UC
5 6 7 8
9
1 2 3 4
B
Display indication
1 2 Screw
DEH-1150MPG/XN/ES
3 4 5 67
DEH-1150MP/XN/ES CXX2204
C
1 Main display section DEH-1150MPG/XN/ES1 (Service)
Shows the various information such as DEH-1190MP/XN/ID
band, play time, and other setting.
• Tuner
Band and frequency are displayed.
• Built-in CD Player
Elapsed playback time and literal infor-
mation are displayed.
3 MP3/WMA indicator
Shows the type of the currently playing disc.
4 RPT indicator
Shows when repeat play is turned on.
E 5 LOUD indicator
Appears when loudness is on.
6 (stereo) indicator
Appears when the selected frequency is
being broadcast in stereo.
7 LOC indicator
Appears when local seek tuning is on.
DEH-1100MP/XN/UC
10
1 2 3 4
5 6 7 8
Power amp
This product (sold separately)
White Gray
Front speaker Front speaker
White/black Gray/black
Left Right
Green Violet
Rear speaker Rear speaker
Green/black Violet/black E
DEH-1100MP/XN/UC
5 6 7 8
11
1 2 3 4
See the table below for the items to be checked regarding audio:
DEH-1100MP/XN/UC
12
1 2 3 4
5 6 7 8
B Keyboard Unit
A:DEH-1100MP/XN/UC C
B:DEH-1150MP/XN/ES
C:DEH-1150MPG/XN/ES
D:DEH-1150MPG/XN/ES1
E:DEH-1150MP/X1N/EC
F:DEH-1190MP/XN/ID
Unit Number : QWM3033(A)
Unit Number : QWM3034(B,C,D,F)
Unit Number : QWM3053(E)
Unit Name : Tuner Amp Unit
Unit Number : (A,C,D,F)
Unit Name : Keyboard Unit
D
Unit Number : (B)
Unit Name : Keyboard Unit
Unit Number : (E)
Unit Name : Keyboard Unit
Unit Number : CWX3514
Unit Name : CD Core Unit(S10.5COMP2)
DEH-1100MP/XN/UC
5 6 7 8
13
1 2 3 4
A - Jigs List
Name Jig No. Remarks
Test Disc TCD-782 Checking the grating
L.P.F. Checking the grating (Two pieces)
- Grease List
B Name Grease No. Remarks
Grease GEM1024 CD Mechanism Module
Grease GEM1045 CD Mechanism Module
3.4 CLEANING
C
DEH-1100MP/XN/UC
14
1 2 3 4
5 6 7 8
DEH-1100MP/XN/UC
5 6 7 8
15
1 2 3 4
4. BLOCK DIAGRAM
A TUNER AMP UNIT
A
SYS+B SWVDD
ANTENNA CN401
LDET
REFB
REFA
CE1
1
IFB
IFA
CE2
DO
CK
DI
SL-IN
SLOUT
AM_ANT
2
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20
IFOUTA
SLOUT
CE1
RFGND1
RFGND2
RFGND3
RFGND4
VDD
DO
IFOUTB
CE2
LDET
VCC
DI
DGND
REFINA
REFINB
ANT
CK
SLIN
IC2
EEPROM SL-IN
IFA
IFB
REFA
REFB
LDET
DI
CK
B CE1
DO
VCO LFP CE2
SLOUT
ATT
ATT TANK
IC1
MIX / IF / PLL
ATT RF LFP
ELEC
CF SOU
FM/AM TUNER UNIT
TUNL
1
IN1_L
C
CDL
2
IN2_L
SYSPW
SYSTEM M
COMPUT
IC 601(2
REGULATOR IC PN5017
DEH-1100MP/XN/UC
16
1 2 3 4
5 6 7 8
CN871
SYSTEM MICRO
COMPUTER 129
KEYD 2
IC 601(1/2)
141
W.REM
PN5017A KEYAD 3
SL-IN 62
SL
IFA 77 IF_INA
CN351
IFB 78 IF_INB RL 2
REFA 96
FREF_A
REFB 97 FREF_B Q351
LDET 99 LOCK
DI 100
DI
CK 101 CK
CE1 102
B
CE
DO 103
DO
CE2 109 VST
SLOUT 136 ADIN7 CN901
ACC SENSE 16
Q931 B.UP
BACK UP
59 35 ASENS ACC
L_OUT ASENS 14
ACC
GND
15
ELECTRONIC VOLUME/
SOURCE SELECTOR
FL 23 FL
7
7 12 AMP 21 FL
TUNL Rear_L RLIn IC 301 FL FL
1 5
IN1_L PAL007C 3 RL FL
RL 8
Front_L
6 14
FLIn RL
5 RL RL C
6
RL
IC 151
CDL
2
PML014A 22 25 B.REMOTE
IN2_L IN4+_L 4 AUX-L MUTE BREM 11
5 AUX-G 6 B.REM
IN4-_L VCC B.UP
4
STBY VCC 20
TEL
9
VCK, VDT, VST
SYSPW
MUTE
Q201(2/2)
SYSTEM MICRO
COMPUTER
IC 601(2/2) MUTE
PN5017A Q201(1/2)
47 44
POWEROFF MUTE
36
BSENS
15
TOP41 D
1
SWVDD
B.UP Q851
26
TELIN
SWVDD
85 DREG 82
XOUT
X601
81 74.1MHz
9 XIN
REGC(M)
55
57
PLL_VDD
DVDD3
AUX IN
1 2
B KEYBOARD UNIT
CN831 CN1801
AUX G
AUX L
94 CN1802
DVDD2
121
DVDD4
AUX-G AUX G
6 6
AUX-L AUX L
7 7
16
CDRESET
34 DSENS DSENS
E
DSENS 14 14
ILMPW
Q821
ILM+B ILL+B
B.UP 9 9
B.UP Q822
2
ILMPW
SWD5V SWVDD
3 3 SWVDD
126
S1801(1/2) KEY MATRIX
PDL3 33 SOURCE SRC
SRC 4 4
SOURCE
S1801(2/2)
111 ROT1 ROT1 1
ROT1 10 10
DEH-1100MP/XN/UC
5 6 7 8
17
1 2 3 4
LCD (CAW1927)
A
E
SEGMENT
COMMON
DEH-1100MP/XN/UC
18
1 2 3 4
5 6 7 8
5. DIAGNOSIS
5.1 OPERATIONAL FLOWCHART
A
Power ON
VDD = 5 V
Pin 8
BSENS
Pin 36
BSENS = L B
ASENS
Pin 35
ASENS = L
Starts
communication
with Grille
microcomputer.
C
300 ms
SWVDD <- H
Pin 1
300 ms
In case of the above signal, the communication
Source keys
with Grille microcomputer may fail.
operative
If the time interval is not 300 msec, the oscillator
may be defective.
Source ON
SYSPW <- H
Pin 15
DEH-1100MP/XN/UC
5 6 7 8
19
1 2 3 4
DEH-1100MP/XN/UC
20
1 2 3 4
5 6 7 8
REAR
A
OUTPUT
1 FR+ 9 MUTE
2 RR+ 10 NC C
3 FR- 11 B.REM
4 RR- 12 NC
5 FL+ 13 A.ANT
6 RL+ 14 ACC
7 FL- 15 GND
8 RL- 16 B.UP
DEH-1100MP/XN/UC
5 6 7 8
21
1 2 3 4
6. SERVICE MODE
6.1 DISPLAY TEST MODE
A
3. Operation method
B
Change display as follows by pushing the 1 and the 3 buttons together.
DEH-1100MP/XN/UC
22
1 2 3 4
5 6 7 8
[CD] or [SOURCE]
Source On
[BAND] [2]
Power Off Tracking Open
DEH-1100MP/XN/UC
5 6 7 8
23
1 2 3 4
7. DISASSEMBLY
While the photograph shown is slightly different from this model in shape, the disassembly procedure is the same.
A
B
2
2 Remove the four screws.
2
Disconnect the connector and then remove the
CD Mechanism Module.
2 2
C
1 1
5
5
F
Tuner Amp Unit
Fig.2
DEH-1100MP/XN/UC
24
1 2 3 4
5 6 7 8
B
B
A
Damper
D
Damper
A
Carriage Mechanism Lower Frame
DEH-1100MP/XN/UC
5 6 7 8
25
1 2 3 4
Screw
B
CD Core Unit
Solder
Planet Gear
Pickup Rack
Chassis
Pickup
DEH-1100MP/XN/UC
26
1 2 3 4
5 6 7 8
DEH-1100MP/XN/UC
5 6 7 8
27
1 2 3 4
Note :
The grating angle of the PU unit cannot be adjusted after the PU unit is changed. The PU unit in the CD mechanism
module is adjusted on the production line to match the CD mechanism module and is thus the best adjusted PU
unit for the CD mechanism module. Changing the PU unit is thus best considered as a last resort. However, if the
PU unit must be changed, the grating should be checked using the procedure below.
Purpose :
To check that the grating is within an acceptable range when the PU unit is changed.
B Symptoms of Mal-adjustment :
If the grating is off by a large amount symptoms such as being unable to close tracking, being unable to perform
track search operations, or taking a long time for track searching.
Method :
Measuring Equipment Oscilloscope, Two L.P.F.
Measuring Points E, F, REFO1
Disc TCD-782
Mode TEST MODE
CD CORE UNIT(S10.5COMP2)
C
REFO1
E F L.P.F.
Xch Ych
E 100 kohm
Oscilloscope
VREF 390 pF
F 100 kohm
VREF 390 pF
D L.P.F.
Checking Procedure
1. In test mode, load the disc and switch the 3 V regulator on.
2. Using the -> and <- buttons, move the PU unit to the innermost track.
3. Press key 3 to close focus, the display should read "91". Press key 2 to implement the tracking balance
adjustment the display should now read "81". Press key 3. The display will change, returning to "81" on the
fourth press.
E 4. As shown in the diagram above, monitor the LPF outputs using the oscilloscope and check that the phase
difference is within 75 degrees. Refer to the photographs supplied to determine the phase angle.
5. If the phase difference is determined to be greater than 75 degrees try changing the PU unit to see if there is any
improvement. If, after trying this a number of times, the grating angle does not become less than 75 degrees then the
mechanism should be judged to be at fault.
Note
Because of eccentricity in the disc and a slight misalignment of the clamping center the grating waveform may be
seen to "wobble" ( the phase difference changes as the disc rotates). The angle specified above indicates the
average angle.
Hint
Reloading the disc changes the clamp position and may decrease the "wobble".
DEH-1100MP/XN/UC
28
1 2 3 4
5 6 7 8
0 degrees 30 degrees
45 degrees 60 degrees
75 degrees 90 degrees
DEH-1100MP/XN/UC
5 6 7 8
29
1 2 3 4
B
DEH-1100MP/XN/UC
DEH-1100MP/XN/UC
DEH-1150MPG/XN/ES
DEH-1150MP/XN/ES
DEH-1150MPG/XN/ES1
DEH-1190MP/XN/ID
DEH-1150MPG/XN/ES
DEH-1150MP/XN/ES
DEH-1150MPG/XN/ES1
DEH-1190MP/XN/ID DEH-1100MP/XN/UC
DEH-1150MPG/XN/ES
DEH-1150MP/XN/ES
DEH-1150MPG/XN/ES1
F DEH-1190MP/XN/ID
DEH-1100MP/XN/UC
30
1 2 3 4
5 6 7 8
16 Remote Control Assy CXC5719 CXC5719 CXC5719 CXC5719 Not used CXC5719
17 Unit Box QHG3019 QHG3020 QHG3021 QHG3022 Not used QHG3023
18 Contain Box QHL3019 QHL3020 QHL3021 QHL3022 Not used QHL3023
19-1 Owner's Manual QRD3016 QRD3017 QRD3017 QRD3017 Not used QRB3010
19-2 Caution Card CRP1387 CRP1387 CRP1387 CRP1387 Not used CRP1387
* 19-3 Warranty Card CRY1276 Not used Not used CRY1250 Not used Not used
* 19-4 Service Network Not used Not used Not used CRY1251 Not used Not used
20 Case Assy Not used YXB5009 YXB5009 YXB5009 YXB5009 YXB5009 C
QRB3010 English
DEH-1100MP/XN/UC
5 6 7 8
31
1 2 3 4
9.2 EXTERIOR(1)
DEH-1190MP/XN/ID
A
B
C
A
B
C B
DEH-1150MP/X1N/EC
DEH-1150MP/X1N/EC
DEH-1100MP/XN/UC
32
1 2 3 4
5 6 7 8
1 Screw See Contrast table (2) 23 Holder See Contrast table (2)
2 Screw BSZ26P060FTC 24 Heat Sink CNR1668
A
3 Screw BSZ26P100FTC 25 FM/AM Tuner Unit CWE2025
4 Screw BSZ26P180FTC
5 Earth Plate See Contrast table (2) 26 Holder CND3466
27 Holder QNC3010
6 Cushion See Contrast table (2) 28 Terminal(CN402) VNF1084
7 Holder See Contrast table (2) 29 Terminal(CN601) VNF1084
8 Chassis Unit CXC7391 > 30 Fuse(10 A) YEK5001
9 CD Mechanism Module(S10.5) CXK5763
10 Screw ISS26P055FTC 31 Button CAC4836
32 Spring CBH2367
11 Cable QDE3003 33 Spring(Silver) CBH2961 B
12 Insulator QNM3015 34 Spring(Black) CBH2962
13 Tuner Amp Unit See Contrast table (2) 35 Cover CNN1665
14 Screw BPZ26P080FTC
15 Screw BSZ26P060FTC 36 Arm CNV9311
37 Arm CNV9312
16 Screw BSZ26P160FTC 38 Panel QNS3023
17 Pin Jack(CN351) CKB1057 39 Transistor(Q991) 2SD2396
18 Plug(CN901) CKM1376 40 IC(IC301) PAL007C
19 Connector(CN651) CKS3829
20 Connector(CN831) CKS5664 41 IC(IC911) BA49181-V12
42 Sheet See Contrast table (2) C
DEH-1100MP/XN/UC
5 6 7 8
33
1 2 3 4
9.3 EXTERIOR(2)
F
64
DEH-1100MP/XN/UC
34
1 2 3 4
5 6 7 8
24 Remote Control Assy CXC5719 CXC5719 CXC5719 CXC5719 Not used CXC5719
25 Cover CNS7068 CNS7068 CNS7068 CNS7068 Not used CNS7068
DEH-1100MP/XN/UC
5 6 7 8
35
1 2 3 4
DEH-1100MP/XN/UC
36
1 2 3 4
5 6 7 8
31 Arm CND2586
32 Bracket CND2587
33 Arm CND2588
34 Lever CND2589
35 Holder CNV9522
36 Gear CNV7207
37 Gear CNV9513
38 Gear CNV7209 E
39 Gear CNV9514
40 Gear CNV9515
41 Gear CNV9516
42 Rack CNV9517
43 Arm CNV7216
44 Roller CNV8189
45 Gear CNV9518
46 Guide CNV9519
F
47 Gear CNV7595
48 Guide CNV9520
49 Arm CNV7805
DEH-1100MP/XN/UC
5 6 7 8
37
1 2 3 4
A-a A-b
Large size
SCH diagram
A-a
C CN701
C
FM/AM TUNER UNIT
B,C,D,E,F
B,C,D,E,F
B,C,D,E,F
B,C,D,E,F
For resistors and capacitors in the circuit diagrams, their resistance values or
capacitance values are expressed in codes:
Ex. *Resistors
Code Practical value
123 12k ohms
103 10k ohms B
*Capacitors CN1801
Code Practical value
103 0.01uF
101/10 100uF/10V
A
DEH-1100MP/XN/UC
38
1 2 3 4
5 6 7 8
A-b
01 A : DEH-1100MP/XN/UC
B : DEH-1150MP/XN/ES A TUNER AMP UNIT
C : DEH-1150MPG/XN/ES
D : DEH-1150MPG/XN/ES1
E : DEH-1150MP/X1N/EC
F : DEH-1190MP/XN/ID
>
C
B,C,D,E,F
B,C,D,E,F
D
BACKUP
GND
ACC
B.REM
A RL-
FL-
RL+
FL+
RR-
FR-
RR+
FR+
A
DEH-1100MP/XN/UC
5 6 7 8
39
F
E
B
A
D
C
40
A-a A-b
A-b
A : DEH-1100MP/XN/UC TUNER AMP UNIT
B : DEH-1150MP/XN/ES A
1
1
C : DEH-1150MPG/XN/ES
D : DEH-1150MPG/XN/ES1
E : DEH-1150MP/X1N/EC
F : DEH-1190MP/XN/ID
2
2
>
DEH-1100MP/XN/UC
3
3
B,C,D,E,F
4
4
B,C,D,E,F
5
5
BACKUP
GND
ACC
B.REM
A RL-
FL-
RL+
FL+
RR-
FR-
6
6
RR+
FR+
DEH-1100MP/XN/UC
7
7
8
8
E
A-a A-b
A-b
41
E
A
D
C
F
B
1 2 3 4
A-b
A
CN701
C
C
A-a A-b
B,C,D,E,F
E
B,C,D,E,F
F
FM/AM TUNER UNIT
A-a
DEH-1100MP/XN/UC
42
1 2 3 4
5
5
A
B,C,D,E,F
6
6
B,C,D,E,F
DEH-1100MP/XN/UC
For resistors and capacitors in the circuit diagrams, their resistance values or
7
7
identical designation.
8
A-a A-b
A-a
A-b
43
E
A
D
C
F
B
1 2 3 4
CLOCK
B
DEH-1100MP/XN/UC
44
1 2 3 4
5 6 7 8
B KEYBOARD UNIT A
B
PWR/VOL
A
CN831
ILL SELECT
B
DEH-1100MP/XN/UC
5 6 7 8
45
1 2 3 4
A
C-a
PICKUP UNIT(P10.5)(SERVICE)
F
%
T
F
T
F PE56
F
T F F
F F
T T T
T T
C #
SWITCHES:
CD CORE UNIT(S10.5COMP2)
S901:HOME SWITCH..........ON-OFF
S903:DSCSNS SWITCH......ON-OFF
S904:12EJ SWITCH.............ON-OFF
S905:8EJ SWITCH...............ON-OFF
The underlined indicates the switch position.
M1 CXC7134
SPINDLE MOTOR
S
C
$
C
M2 CXC4026
LOADING/CARRIAGE MOTOR T S
9 7
F C
0 8 4
E 5
CD DRIVER
C
DEH-1100MP/XN/UC
46
1 2 3 4
5 6 7 8
A
C-b
C CD CORE UNIT(S10.5COMP2)
!
B
SIGNAL LINE
F
FOCUS SERVO LINE
T
TRACKING SERVO LINE
C
CARRIAGE SERVO LINE
S
SPINDLE SERVO LINE
PE5668A
A
CN651
^ &
C
DEH-1100MP/XN/UC
5 6 7 8
47
F
E
B
A
D
C
48
C-a C-b
C-b
1
1
C CD CORE UNIT(S10.5COMP2)
2
2
SIGNAL LINE
F
FOCUS SERVO LINE
T
TRACKING SERVO LINE
C
CARRIAGE SERVO LINE
S
DEH-1100MP/XN/UC
SPINDLE SERVO LINE
3
3
PE5668A
4
4
5 6 7 8
CN651
A
A
6
B
&
^
C
C-a C-b
D
2 3 C-b
DEH-1100MP/XN/UC
5 6 7 8
49
F
E
B
A
D
C
50
C-a C-b
C-a
C-b
1
1
PICKUP UNIT(P10.5)(SERVICE)
2
2
F
%
DEH-1100MP/XN/UC
T
F
3
3
T
F
P
F
T F F
F F
T T T
T T
4
4
SWITCHES:
CD CORE UNIT(S10.5COMP2)
S901:HOME SWITCH..........ON-OFF
S903:DSCSNS SWITCH......ON-OFF
S904:12EJ SWITCH.............ON-OFF
S905:8EJ SWITCH ON-OFF
SWITCHES:
CD CORE UNIT(S10.5COMP2)
S901:HOME SWITCH..........ON-OFF
S903:DSCSNS SWITCH......ON-OFF
S904:12EJ SWITCH.............ON-OFF
S905:8EJ SWITCH...............ON-OFF
The underlined indicates the switch position.
5
5
M1 CXC7134
SPINDLE MOTOR
2
C
$
C
M2 CXC4026
T
6
6
LOADING/CARRIAGE MOTOR S
9 7
F C
0 8 4
DEH-1100MP/XN/UC
2
7
7
CD DRIVER
3
8
8
C-a c-b
C-a
C-b
51
E
A
D
C
F
B
1 2 3 4
10.4 WAVEFORMS
- CD CORE UNIT Note : 1. The encircled numbers denote measuring points in the circuit diagram.
A
2. Reference voltage REFO1(1.65 V)
1 DSCSNS 5 V/div 500 ms/div 1 DSCSNS 5 V/div 500 ms/div 1 DSCSNS 5 V/div 500 ms/div
2 8SNS 5 V/div 5 CLCONT 5 V/div 2 8SNS 5 V/div
3 12SNS 5 V/div 4 LOEJ 5 V/div 3 12SNS 5 V/div
4 LOEJ 5 V/div 6 VD 10 V/div 4 LOEJ 5 V/div
12 cm CD Loading operation 12 cm CD Loading operation 8 cm CD Loading operation
7 SIN 1 V/div 1 s/div 0 FIN 200 mV/div 500 ms/div @ TE 500 mV/div 200 ms/div
8 CIN 500 mV/div ! RFOK(MONI_2) 2 V/div # FE 500 mV/div
9 TIN 1 V/div 7 SIN 2 V/div
12 cm CD-DA setup operation after loading 12 cm CD-DA Source On setup operation Source On setup operation
# FE 500 mV/div 20 ms/div $ MDX 2 V/div 200 ms/div $ MDX 2 V/div 5 µs/div
0 FIN 500 mV/div 7 SIN 500 mV/div 7 SIN 500 mV/div
@ TE 500 mV/div
D 9 TIN 500 mV/div
CD-DA Play operation Spindle waveform during play operation Spindle waveform during play operation
(Wider)
E
0 FIN 500 mV/div 200 ms/div @ TE 500 mV/div 2 ms/div % RFAGC 1 V/div 500 µs/div
# FE 500 mV/div % RFAGC 500 mV/div @ TE 500 mV/div
9 TIN 500 mV/div
DEH-1100MP/XN/UC
52
1 2 3 4
5 6 7 8
A
% RFAGC 1 V/div 500 µs/div % RFAGC 1 V/div 500 µs/div % RFAGC 1 V/div 2 ms/div
@ TE 500 mV/div @ TE 500 mV/div @ TE 500 mV/div
9 TIN 500 mV/div 9 TIN 500 mV/div 9 TIN 500 mV/div
% RFAGC 1 V/div 200 ms/div ^ LOUT 1 V/div 200 µs/div 1 DSCSNS 5 V/div 500 ms/div
@ TE 1 V/div & ROUT 1 V/div 2 8SNS 5 V/div
8 CIN 1 V/div 3 12SNS 5 V/div
7 SIN 2 V/div 4 LOEJ 5 V/div
Search operation(Outter to Inner) Analog audio waveform 12 cm CD Eject operation
1 DSCSNS 5 V/div 500 ms/div 1 DSCSNS 5 V/div 500 ms/div % RFAGC 1 V/div 500 µs/div
5 CLCONT 5 V/div 2 8SNS 5 V/div 9 TIN 1 V/div
4 LOEJ 5 V/div 3 12SNS 5 V/div @ TE 1 V/div
4 LOEJ 5 V/div 0 FIN 1 V/div
12 cm CD Eject operation 8 cm CD Eject operation Black dot(800 μm) during play D
DEH-1100MP/XN/UC
5 6 7 8
53
1 2 3 4
SIDE B
P.C.Board Chip Part
C CN701
B CN1801
A
DEH-1100MP/XN/UC
54
1 2 3 4
5 6 7 8
SIDE A
ASSY
RCA
2
1
ANTENNA B
F
FRONT
A
DEH-1100MP/XN/UC
5 6 7 8
55
1 2 3 4
A
DEH-1100MP/XN/UC
56
1 2 3 4
5 6 7 8
SIDE B
A
DEH-1100MP/XN/UC
5 6 7 8
57
F
E
B
A
D
C
58
B
B
1
1
KEYBOARD UNIT
11.2 KEYBOARD UNIT
D1824
2
2
40 D1807
S1820 S1812
S1809 EJECT
S1817 S1816
D1834
FUNC D1825
D1817
40 35 30 25 20 15 10 5 1
30 AUDIO LCD1801 DISP
S1802
S1821 S1811 D1808
D1837
D1820
D1806
PWR
/VOL D1826
20 D1818 S1801
D1816 S1808
D1835 IC1802
D1833 CLOCK D1809
S1822 S1810 1
DEH-1100MP/XN/UC
D1838
D1821
EQ 5 6
S1815 1 2 3 4
BAND S1818 S1813 S1803 S1804 S1819 S1814
D1831
D1815
D1832
D1827
D1812
D1829
D1813
D1830
D1810
D1814
D1828
D1811
10 S1805
S1807 S1806 AUX
3
3
D1819
D1836
Y CN1802
0
10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160
X
4
4
SIDE A
B
F
C
D
A
59
B
SIDE B
8
8
A CN831
40
7
7
DEH-1100MP/XN/UC
50
30
R1808
R1803
55 45 S1833
R1835 40
60 R1812
R1811
R1806
R1832 R1809 35
R1804
R1813
1 R1807
C1803 R1834
R1836 IC1801
R1839
R1840 1 20
D1803
D1805
R1810
R1805
R1837
5 30
C1810
C1811 R1838
D1804
10 25 5 1
R1833 C1801
20
X1801
15 R1814
R1831
D1802
D1801 CN1801 10
R1802
R1801 10
Y
6
6
0
160 150 140 130 120 110 100 90 80 70 60 50 40 30 20 10
X
KEYBOARD UNIT
5
5
B
1 2 3 4
E
M2
LOADING
/CARRIAGE
MOTOR
M1
SPINDLE
MOTOR
C
DEH-1100MP/XN/UC
60
1 2 3 4
5 6 7 8
C
DEH-1100MP/XN/UC
5 6 7 8
61
1 2 3 4
DEH-1100MP/XN/UC
5 6 7 8
63
1 2 3 4
Circuit Symbol and No. Part No. Circuit Symbol and No. Part No.
C 164 (A,120,113) CEJQ100M16 C 642 (B,109,103) CKSRYB182K50
C
602
603
(B,121,30)
(B,123,28)
CKSRYB103K50
CKSRYB103K50
B
Unit Number : (A,C,D,F)
C 605 (B,108,74) CKSRYB104K16
C 606 (B,105,56) CKSRYB103K50
Unit Name : Keyboard Unit
C 607 (B,118,55) CKSRYB103K50
C 608 (B,95,80) CKSRYB103K50 MISCELLANEOUS
CAPACITORS
B
Unit Number : (B)
IC 1801
IC 1802
(B,103,21)
(A,159,22)
IC
Remote IC
PD6340A
GP1UXC14RK
D 1803 (B,150,19) Diode MALS068X
Unit Name : Keyboard Unit D 1804 (B,152,17) Diode MALS068X
D 1805 (B,146,19) Diode MALS068X
MISCELLANEOUS
D 1806 (A,60,22) White LED NESW505C-5273 C
IC 1801 (B,103,21) IC PD6340A D 1807 (A,145,40) LED CL-195PG-CD
IC 1802 (A,159,22) Remote IC GP1UXC14RK D 1808 (A,148,29) LED CL-195PG-CD
D 1803 (B,150,19) Diode MALS068X D 1809 (A,148,19) LED CL-195PG-CD
D 1804 (B,152,17) Diode MALS068X D 1810 (A,107,8) LED CL-195PG-CD
D 1805 (B,146,19) Diode MALS068X
D 1811 (A,120,8) LED CL-195PG-CD
D 1806 (A,60,22) White LED NESW505C-5273 D 1812 (A,133,8) LED CL-195PG-CD
D 1807 (A,145,40) LED CL-195SR-CD D 1813 (A,68,8) LED CL-195PG-CD
D 1808 (A,148,29) LED CL-195SR-CD D 1814 (A,81,8) LED CL-195PG-CD
D 1809 (A,148,19) LED CL-195SR-CD D 1815 (A,94,8) LED CL-195PG-CD
D 1810 (A,107,8) LED CL-195SR-CD
D 1816 (A,52,19) LED CL-195PG-CD
D 1811 (A,120,8) LED CL-195SR-CD D 1817 (A,37,32) LED CL-195PG-CD D
D 1812 (A,133,8) LED CL-195SR-CD D 1818 (A,25,19) LED CL-195PG-CD
D 1813 (A,68,8) LED CL-195SR-CD D 1819 (A,37,5) LED CL-195PG-CD
D 1814 (A,81,8) LED CL-195SR-CD D 1820 (A,11,30) LED CL-195PG-CD
D 1815 (A,94,8) LED CL-195SR-CD
D 1821 (A,11,12) LED CL-195PG-CD
D 1816 (A,52,19) LED CL-195SR-CD D 1824 (A,148,40) LED CL-195D-CD
D 1817 (A,37,32) LED CL-195SR-CD D 1825 (A,149,30) LED CL-195D-CD
D 1818 (A,25,19) LED CL-195SR-CD D 1826 (A,149,20) LED CL-195D-CD
D 1819 (A,37,5) LED CL-195SR-CD D 1827 (A,108,8) LED CL-195D-CD
D 1820 (A,11,30) LED CL-195SR-CD
D 1828 (A,121,8) LED CL-195D-CD
D 1821 (A,11,12) LED CL-195SR-CD D 1829 (A,134,8) LED CL-195D-CD
E
X 1801 (B,95,13) Ceramic Resonator 5.00 MHz CSS1731 D 1830 (A,69,8) LED CL-195D-CD
S 1801 (A,38,18) Rotary Switch(PWR/VOL) YSD5019 D 1831 (A,82,8) LED CL-195D-CD
LCD1801 (A,135,31) LCD CAW1927 D 1832 (A,95,8) LED CL-195D-CD
DEH-1100MP/XN/UC
5 6 7 8
65
1 2 3 4
Circuit Symbol and No. Part No. Circuit Symbol and No. Part No.
RESISTORS R 225 (A,49,49) RS1/16SS103J
R 226 (A,49,50) RS1/16SS393J
R 1801 (B,75,6) RS1/16S222J R 227 (B,45,51) RS1/16SS562J
R 1802 (B,79,8) RS1/16S222J R 228 (B,42,53) RS1/16SS122J
A
R 1803 (B,144,28) RS1/4SA561J R 229 (B,44,53) RS1/16SS472J
R 1804 (B,134,23) RS1/4SA561J
R 1805 (B,73,20) RS1/4SA561J R 230 (B,21,28) RS1/16SS0R0J
R 232 (B,43,51) RS1/16SS122J
R 1806 (B,50,24) RS1/4SA391J R 233 (B,29,52) RS1/16SS103J
R 1807 (B,19,22) RS1/4SA751J R 234 (B,30,61) RS1/16SS473J
R 1808 (B,147,28) RS1/4SA681J R 235 (A,25,63) RS1/16SS473J
R 1809 (B,139,23) RS1/4SA681J
R 1810 (B,76,20) RS1/4SA681J R 239 (B,26,48) RS1/16SS473J
R 240 (B,10,31) RS1/16SS473J
R 1811 (B,25,24) RS1/4SA471J R 241 (B,9,32) RS1/16SS103J
R 1812 (B,19,25) RS1/4SA821J R 244 (A,20,52) RS1/16SS473J
B R 1813 (B,55,23) RS1/4SA821J R 255 (A,27,63) RAB4CQ104J
R 1832 (B,155,24) RS1/16S2R2J
R 1834 (B,154,22) RS1/16S101J R 307 (A,34,19) RS1/16SS183J
R 308 (A,38,20) RS1/16SS183J
R 1835 (B,158,25) RS1/16S103J R 309 (A,35,21) RS1/16SS183J
R 1836 (B,136,20) RS1/16S101J R 310 (A,38,21) RS1/16SS183J
R 1837 (B,144,17) RS1/16S101J R 601 (B,28,38) RS1/16SS0R0J
R 1839 (B,51,20) RS1/16S473J
R 602 (B,27,41) RS1/16SS0R0J
CAPACITORS R 606 (B,23,41) RS1/16SS0R0J
R 701 (B,16,35) RS1/16SS221J
C 1801 (B,112,14) CKSRYB105K10 R 702 (A,23,55) RS1/16SS221J
C 1803 (B,159,24) CKSYF106Z10
C C 1810 (B,143,16) CKSRYB472K50 CAPACITORS
C 1811 (B,136,19) CKSRYB472K50
C 106 (B,56,69) CKSQYB475K6R3
C
C 202 (A,27,57) CKSSYB104K10
C 204 (A,24,63) CKSSYB103K16
Unit Number : CWX3514 C 205 (B,23,43) CKSQYB475K6R3
C 206 (A,22,39) CKSSYB104K10
Unit Name : CD Core Unit(S10.5COMP2)
C 207 (A,24,37) CKSRYB104K16
MISCELLANEOUS C 209 (B,33,40) CEVW220M6R3
C 210 (B,29,42) CKSSYB104K10
IC 201 (A,34,46) IC PE5668A C 211 (A,27,34) CKSSYB104K10
IC 301 (A,27,14) IC BA5839FP C 212 (B,29,32) CKSRYB104K16
D
Q 101 (B,56,72) Transistor 2SA1577
Q 102 (B,47,57) Chip Transistor 2SB1689 C 213 (A,44,37) CKSSYB104K10
X 201 (A,23,35) Ceramic Resonator 16.934 MHz CSS1603 C 214 (A,28,33) CKSSYB104K10
C 216 (A,50,51) CKSSYB332K50
S 901 (A,53,37) Switch(HOME) CSN1067 C 217 (A,46,51) CKSSYB104K10
S 903 (B,19,58) Switch(DSCSNS) CSN1067 C 218 (A,49,51) CKSSYB473K10
S 904 (B,38,67) Switch(12EJ) CSN1068
S 905 (B,24,68) Switch(8EJ) CSN1068 C 219 (A,45,53) CKSSYB104K10
C 220 (A,46,53) CKSSYB182K50
RESISTORS C 221 (A,44,53) CKSSYB104K10
C 222 (B,43,53) CCSSCH560J50
R 101 (B,60,73) RS1/10SR2R4J C 223 (B,45,53) CCSSCH4R0C50
E R 102 (B,59,71) RS1/10SR2R4J
R 103 (B,60,71) RS1/10SR2R7J C 224 (A,43,55) CKSSYB104K10
R 104 (B,52,69) RS1/16SS222J C 226 (A,40,58) CCSSCH680J50
R 105 (B,41,57) RS1/16SS102J C 227 (A,40,60) CCSSCH470J50
C 228 (A,39,62) CKSSYB103K16
R 107 (B,41,59) RS1/16SS105J C 229 (B,49,59) CKSSYB104K10
R 202 (B,32,62) RS1/16SS473J
R 203 (B,42,45) RS1/16S473J C 236 (A,42,61) CKSSYB104K10
R 204 (A,25,61) RS1/16SS221J C 239 (B,44,51) CCSSCH220J50
R 206 (B,26,53) RS1/16SS104J C 240 (A,35,61) CKSSYB104K10
C 250 (B,36,30) CKSSYB102K50
R 210 (B,13,32) RS1/16SS102J C 251 (B,33,29) CKSSYB102K50
R 214 (B,36,34) RS1/16SS472J
F R 216 (B,47,49) RS1/16SS472J C 303 (A,35,19) CKSSYB472K25
R 221 (B,36,32) RS1/16SS103J C 304 (A,34,21) CKSSYB223K16
R 222 (B,35,32) RS1/16SS103J C 307 (B,25,9) CKSRYB104K16
C 308 (B,10,27) CKSRYB105K10
DEH-1100MP/XN/UC
66
1 2 3 4
5 6 7 8
Circuit Symbol and No. Part No.
C 703 (B,11,37) CCSSCH101J50
DEH-1100MP/XN/UC
5 6 7 8
67