Professional Documents
Culture Documents
CRT3688
DEH-P9800BT/XN/EW5
DEH-P9800BT /XN/EW5
This service manual should be used together with the following manual(s):
Model No. Order No. Mech.Module Remarks
CX-3164 CRT3583 S10.5COMP1 CD Mech. Module : Circuit Descriptions, Mech. Descriptions, Disassembly
SAFETY INFORMATION
A This service manual is intended for qualified service technicians; it is not meant for the casual do-it-yourselfer.
Qualified technicians have the necessary test equipment and tools, and have been trained to properly and safely
repair complex products such as those covered by this manual.
Improperly performed repairs can adversely affect the safety and reliability of the product and may void the warranty.
If you are not qualified to perform the repair of this product properly and safely, you should not risk trying to do so
and refer the repair to a qualified service technician.
CAUTION:
USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF PROCEDURES OTHER THAN THOSE
SPECIFIED HEREIN MAY RESULT IN HAZARDOUS RADIATION EXPOSURE.
CLASS 1
D
LASER PRODUCT
WARNING!
The AEL (accessible emission level )of the laser power output is less than CLASS 1
but the laser component is capable of emitting radiation exceeding the limit for
CLASS 1.
A specially instructed person should do servicing operation of the apparatus.
E
Laser diode characteristics
Wave length : 785 to 814 nm
Maximum output : 1 190 µW(Emitting period : unlimited)
DEH-P9800BT/XN/EW5
2
1 2 3 4
5 6 7 8
CAUTION
Danger of explosion if battery is incorrectly replaced. A
Replaced only with the same or equivalent type recommended by the manufacture.
Discord used batteries according to the manufacture's instructions.
- Service Precaution
1. You should conform to the regulations governing
the product (safety, radio and noise, and other
regulations), and should keep the safety during
servicing by following the safety instructions
B
described in this manual.
2. Before disassembling the unit, be sure to turn off
the power. Unplugging and plugging the connectors
during power-on mode may damage the ICs inside
the unit.
3. To protect the pickup unit from electrostatic discharge
during servicing, take an appropriate treatment
(shorting-solder) by referring to "the DISASSEMBLY".
4. After replacing the pickup unit, be sure to check the
grating.
5. Be careful in handling ICs. Some ICs such as MOS
type are so fragile that they can be damaged by C
electrostatic induction.
DEH-P9800BT/XN/EW5
5 6 7 8
3
1 2 3 4
Please follow the specified safety methods when modification(addition/change of parts) is required due to interferences such as
radio/TV interference and foreign noise.
When you solder while repairing, please be sure that there are no cold solder and other debris.
Soldering should be finished with the proper quantity. (Refer to the example)
Please be sure that all screws are fastened, and that there are no loose screws.
Please be sure that all connectors are inserted, and that there are no imperfect insertion.
6 Make sure the wiring cables are set to their original state.
Please replace the wiring and cables to the original state after repairs.
C In addition, be sure that there are no pinched wires, etc.
7 Make sure screws and soldering scraps do not remain inside the product.
Please check that neither solder debris nor screws remain inside the product.
8 There should be no semi-broken wires, scratches, melting, etc. on the coating of the power cord.
Damaged power cords may lead to fire accidents, so please be sure that there are no damages.
If you find a damaged power cord, please exchange it with a suitable one.
When spark traces or similar marks are found on the power supply plug, please check the connection and advise on secure
connections and suitable usage. Please exchange the power cord if necessary.
When you perform repairs, please pay attention to static electricity, furniture, household articles, etc. in order to prevent injuries.
Please pay attention to your surroundings and repair safely.
2. Adjustments
To keep the original performance of the products, optimum adjustments and confirmation of characteristics within specification.
Adjustments should be performed in accordance with the procedures/instructions described in this manual.
4. Cleaning
For parts that require cleaning, such as optical pickups, tape deck heads, lenses and mirrors used in projection monitors, proper
cleaning should be performed to restore their performances.
DEH-P9800BT/XN/EW5
4
1 2 3 4
5 6 7 8
CONTENTS
SAFETY INFORMATION......................................................................................................................................2
1. SPECIFICATIONS .............................................................................................................................................6
2. EXPLODED VIEWS AND PARTS LIST.............................................................................................................8 A
2.1 PACKING ....................................................................................................................................................8
2.2 EXTERIOR(1) ...........................................................................................................................................10
2.3 EXTERIOR(2) ...........................................................................................................................................12
2.4 CD MECHANISM MODULE .....................................................................................................................14
3. BLOCK DIAGRAM AND SCHEMATIC DIAGRAM ..........................................................................................16
3.1 BLOCK DIAGRAM....................................................................................................................................16
3.2 OVERALL CONNECTION DIAGRAM(GUIDE PAGE) ..............................................................................20
3.3 TUNER AMP UNIT(DSP)..........................................................................................................................26
3.4 KEYBOARD UNIT ....................................................................................................................................28
3.5 CD CORE UNIT(COMP1D)(GUIDE PAGE)..............................................................................................30
3.6 BLUETOOTH UNIT, ANTENNA UNIT ......................................................................................................40
4. PCB CONNECTION DIAGRAM ......................................................................................................................42 B
4.1 TUNER AMP UNIT ...................................................................................................................................42
4.2 KEYBOARD UNIT ....................................................................................................................................46
4.3 CD CORE UNIT(COMP1D) ......................................................................................................................48
4.4 BLUETOOTH UNIT...................................................................................................................................50
4.5 ANTENNA UNIT .......................................................................................................................................52
4.6 SWITCH UNIT ..........................................................................................................................................53
5. ELECTRICAL PARTS LIST .............................................................................................................................54
6. ADJUSTMENT ................................................................................................................................................65
6.1 DISPLAY TEST MODE .............................................................................................................................65
6.2 CD ADJUSTMENT ...................................................................................................................................66
6.3 CHECKING THE GRATING AFTER CHANGING THE PICKUP UNIT.....................................................68
6.4 ERROR MODE .........................................................................................................................................70 C
6.5 SYSTEM MICROCOMPUTER TEST PROGRAM ....................................................................................71
6.6 HOW TO CHECK THE REVOLUTION NUMBER DETECTION CIRCUIT................................................71
6.7 E.VOL IC OSCILLATING FREQUENCY ADJUSTMENT..........................................................................72
6.8 BLUETOOTH TEST MODE ......................................................................................................................73
7. GENERAL INFORMATION .............................................................................................................................78
7.1 DIAGNOSIS..............................................................................................................................................78
7.1.1 DISASSEMBLY......................................................................................................................................78
7.1.2 CONNECTOR FUNCTION DESCRIPTION ..........................................................................................83
7.2 IC ..............................................................................................................................................................84
7.3 OPERATIONAL FLOW CHART ..............................................................................................................104
8. OPERATIONS ...............................................................................................................................................105
D
DEH-P9800BT/XN/EW5
5 6 7 8
5
1 2 3 4
1. SPECIFICATIONS
DEH-P9800BT/XN/EW5
6
1 2 3 4
5 6 7 8
DEH-P9800BT/XN/EW5
5 6 7 8
7
1 2 3 4
26
B
24
2 27 16
23
8 12
C 11 17
9 28
11
4
10 5
15
9 7 28 28
6 13
13 14
19
3
20
D
22 18
19
21
20
DEH-P9800BT/XN/EW5
8
1 2 3 4
5 6 7 8
PACKING SECTION PARTS LIST
Mark No. Description Part No. Mark No. Description Part No.
CRB2178 Russian
DEH-P9800BT/XN/EW5
5 6 7 8
9
1 2 3 4
2.2 EXTERIOR(1)
27
A
24
26
25 27
27
5
4
3
5
2 1
B
4
9
11
9
20 9
13 29 18
15
9
B
C
12 17
10 30
19 16
21
14
23
22
8
31
6
28
DEH-P9800BT/XN/EW5
10
1 2 3 4
5 6 7 8
EXTERIOR(1) SECTION PARTS LIST
Mark No. Description Part No.
1 Cord Assy CDE6562
> 2 Fuse(10 A) CEK1136 A
3 Cap CKX-003
4 Cap CNS1472
5 Resistor RS1/2PMF102J
11 Cover CNS8491 B
12 Holder CNV8834
13 Lighting Conductor CNV9010
14 Lighting Conductor CNV9011
15 Lighting Conductor CNV9013
16 Cable CDE8057
17 Connector(CN1931) CKS5090
18 Connector(CN1701) CKS5662
19 Sheet CNM8658
20 Cushion CNM9946
C
21 OEL Module MXK8230
22 Grille Unit CXC5600
23 Knob Unit(MULTI-CONTROL) CXC5674
24 Remote Control Unit CXC5715
25 Cover CZN5357
31 Cushion CNN1405
DEH-P9800BT/XN/EW5
5 6 7 8
11
1 2 3 4
2.3 EXTERIOR(2)
50
49
A 7
2 52
54 53 51
84 F 93
48
81 A
79 48
78 83
C
77 82
B
77
85
80 81 2 86
78 79 87 14
B
5
20
1 1
1 71
1
43 42 28
40 19
E 18
39 17 1
47
4 17
41 D
C 45
16 36 75
35 31 21 34 18 12
1 29 76 26
15
30 E 10
6 32 22
15 21
73
21 7615 46
27 23
33 12
B
37
D F
A
38 10
25
24
21 72
57 63 11
D
65 56 8
44
57 57
64 56
E 3 74
(1)
70
A 9 13
68 58 F
56 1
60
3 90 62 (1)
(3) 59 89 D
74 (1)
91 61
(1)
74 (1)
(1) E
88
55 92
(1) 69
67
69 74
F C
(1) : GEM1024 56
(1) 66 56
(3) : GEM1069
74 3 56
3
DEH-P9800BT/XN/EW5
12
1 2 3 4
5 6 7 8
EXTERIOR(2) SECTION PARTS LIST
Mark No. Description Part No. Mark No. Description Part No.
DEH-P9800BT/XN/EW5
5 6 7 8
13
1 2 3 4
DEH-P9800BT/XN/EW5
14
1 2 3 4
5 6 7 8
CD MECHANISM MODULE SECTION PARTS LIST
Mark No. Description Part No. Mark No. Description Part No.
31 Arm CND2586
32 Bracket CND2587
33 Arm CND2588
34 Lever CND2589
35 Holder CNV7201
36 Gear CNV7207
37 Gear CNV7208
38 Gear CNV7209 E
39 Gear CNV7210
40 Gear CNV7211
41 Gear CNV7212
42 Rack CNV7214
43 Arm CNV7216
44 Roller CNV7218
45 Gear CNV7219
46 Guide CNV7361
47 Gear CNV7595 F
48 Guide CNV7799
49 Arm CNV7805
DEH-P9800BT/XN/EW5
5 6 7 8
15
1 2 3 4
TUNPCE2
TUNPDO
TUNPCE1
TUNPDI
TUNPCK
LDET
NJM45
SL
OUT 3
MICROPHONE MIC
2
7 6 13 5 10 9 8 11 14 18 19 20 21 V
FM/AM TUNER UNIT
NC
CE2
ROM_VDD
SL
DI
CK
CE1
LDET
DO
RDS_CK
RDS_DATA
RDS_LOCK
RDS_HSLK
IC 3 EEPROM IC 5
5.0V 5V 3.3V
OSC LPF
B ANTENNA CN401
DSP
AM ANT FMRF
1 IC201
1 ATT
AK7732
Rch
2,3 24 43
XTI
IC 2
1 CK_
2.5V 42
2 FM ANT IC 1 XTO S_
3.3V X201
3 ATT Lch 16.9344MHz INIT
23
CN402 FMRF MIXER, IF AMP DET, FM MPX, 16
RDS DECODER CLK02
RF adj
ANT adj
CDDT 22 SDIN5A/JX0 R
CDBCK 25 SC
BITCLK_I
CDLRCK 26
LRCLK_I SD
T51 CF52
F 37 SDOUT1
R 36 SDOUT2
SW 35 SDOUT3
MCK1 32
CLKO1
LRCK0 39
AUDIOGND
LRCLK_0
IC 4
OSCGND
BCK0 38
VDD_3.3
BITCLK_0
RFGND
VCC
NC
C 2 12 15 22 16 4 17
TUN3V REGULATOR
TUN3V IC421
3 NJM2885DL1-33 1
TUN8V D/A CONVERTER
IC221
PCM1606EG NJ
AUX AMP F 1 5
IC441 DATA1 FL 10
NJM4558MD R 2
DATA2 12 3
CN441 2 3 SW 3 RL
1 AUXL DATA3
AUX 3 2 MCK1 20
SCKI
1 LRCK0 18
IC271 LRCK
BCK0 19 NJ
CN702 TC7SH08FUS1 BCK
2 MCK2 8 5
CDMCKO 4 SWL
1 1
CDRX
3
CDTX MCK SW
4
CN101 TUN
7 BUSL+ BUSL+ BUS
11 BUSL- BUSL- BUS
5 AUBT
IP-BUS 1
8
IP-BUS DRIVER
D BUS- 1 TX 37
PICKUP UNIT
(P10.5)(SERVICE)
C CD CORE UNIT(COMP1D) 1 3 4
6
IC101
BUS+5 HA12241FP 2 RX
8
36
TX
RX
AU
CN902 IPPW 64
IPPW
V3R3D
Q101
LASER CN101 34 CN901 CN701 F
DIODE LD- 142 B.UP
15 15 LD 50 XTAL LRCK LRCK CDLRCK
LRCK 16 5
MD Q101
143
49 IC201 65
5 5 PD LRCKIN
UPD63763CGJ DOUT ASENBO
REFO 46 DATA CDDT
VREF 8 133 DOUT 14 7
8 REFOUT 45
AC,BD RF-AMP,CD DECODER, DIN
BCK AUX SELECT A
HOLOGRAM MP3 , WMA, DECODER, 48 BCLK CDBCK IC122
SCKO 15 6
UNIT DIGITAL SERVO / DATA PROCESSOR SCKIN 47 TC4066BFT
F,E
FOM FOM 8
3 3
LOCK/RFOK 9,10
FOP FOP BTAVL 11
FOCUS ACT. 2 2 56 A
XRST,XASTB,ADO,XCK,
MONITOR TOP
1 TOP
XSO,XSI,WAIT,XINT
DEH-P9800BT/XN/EW5
16
1 2 3 4
5 6 7 8
CN431
ASL MIC 3
AUTO EQ IC431
MIC IN
IC161(1/2) IC161(2/2) IC162(1/2) IC162(2/2) TC4066BFT MICCS
MIC161 2
NJM4558MD NJM4558MD NJM4558MD NJM4558MD Q181 3 1,4 CN561
OUT 3 1 5 7 ASLIN 139 AEQMIC 2 BTPW2 BTPW2
CROPHONE MIC ASLIN B 6
5 7 3 1 SYSTEM 8 RST
9,10 AEQHFO 4
2 CONTROLLER AEQO 11 BOOTE
VR161 5
IC601(1/2) TX
PEG259A Q182 5,6 12,13 2
RX
TUNPCE2 35 VDD SYS+B 1
TUNPCE2
TUNPCE1 34 CN551(1/2)
TUNPCE1 RX
TUNPDI 49 Q431 40
TUNPDI Q183 TX
TUNPDO 50 66 39
TUNPDO MICSEN BOOTE
TUNPCK 51 36
TUNPCK BTHF_AEQ 78 TELOUT
SL 141 15
SL 96 BTMIC
Q402 LDET 26 BTMUTE 17
LDET Q531 BTRST
94
RDS_CK 25 BTRST 6
RCK 116 DACDT
DACDT 33
RDS_LOCK 48
RDSLK DACCK
115
114
DACCK
DACCS 35
34 E
DACCS CN76
Q401
DSP RDS_DATA 33
RDT 95 BTTEST
B
BTTEST 5
IC201 46 BTRTS3
RDS_HSLK 30 RTSO 4
AK7732VT RDS57K 44 BTTX3
BTTX 2
43 31 77 3V 5V BTAVL BTAVL
XTI CKM[2]
28 72
SMODE
47 6 4
A BTCTS3
24
CK_RESET CKRST BTCTS 3
42 29 73 45 8 9 BTRX3
XTO S_RESET DSPRST BTRX 1
X201 27 71 6 3 1
16.9344MHz INIT_RESET DSPIRST MEMDI RCA OUT
CN321
5V 3V IC501 SWL MUTE SWL
16 IC262 9 SW L
CLK02 TC74VHC08FTS1 TC74VHCT08AFTS1
8 11 12 75
DSPRQ Q323
22 SDIN5A/JX0 RQ/CAD1 14 6 4 89 5V 3V 2 10
SCLK/SCL DSPCK SO FL FL
25 11 3 1 90 5 12 11 5 1 FRONT L
BITCLK_I SI/CAD0 DSPOUT MEMDO SI
26 7 9 8 6
LRCLK_I SDIN3/JX2 20 8 9 69
DSPRAMCLR MEMCK
SCK Q321 2
87 4 6 3
MEMWP W#
3V 5V 86 1 3 1 RL
37 MEMCS CS 5 REAR L
SDOUT1 IC261
36 TC74VHCT08AFTS1 FU321
SDOUT2 IC511 MEMORY Q322 6
9 4 6 70 TC74VHC08FTS1
35 SDOUT3 RDY DSPDRDY IC521
10 1 3 88 S99-50084 CN991
32 SO DSPIN BACKUP SENSE B.UP
CLKO1 104 BSENS B.UP FUSE BACKUP
39 BSENS 1
LRCLK_0 AINL+
64 INPUT ADC 10A
38 6 103 ASENS Q931 ACC
BITCLK_0 63 7 ASENS 5 ACC
AINL- 5 BUFFER 134 ACC SENSE
1,2 3 BATIND
IC240 SYS+B BATIND
Q941
NJM4558MD
IC241 ISENS
105 ISENS ILL
3 ILL C
NJM4558MD TEL IN
ILL SENSE Q951
D/A CONVERTER ELECTRONIC VOLUME/ 123 TELIN TEL
8 TEL
LPF SOURCE SELECTOR TELIN
IC221 IC281
PCM1606EG F V SYS+B
NJM4558MD 16 BRE
So1L IC752 4
1
DATA1 FL 10
5 7 19 44 NJM4151M INV. 5 AMP 8 Q793 AMP AMP B.REM
Vi1(FL) SCK
2 SDA 43 136 1 6 4 2 7 6 1 2 7 5
DATA2 22 GAUGE IO TB
3 12 3 1 45 60 EVOLCS
RL Vi3(RL) CS GND
DATA3 2
20 55 IC754 IC751 IC753(1/2) IC753(2/2)
18
SCKI LPF EX1+ C TC7S14FU NJM4558MD NJM4558MD NJM4558MD
LRCK IC282
19 NJM4558MD 33 SWL POWER AMP
BCK Q281 Vo5a 6,20
8 5 7 25 VCC B.UP
SWL Vi5(SWL) 29 FL 25
Vo1a B.REMOTE
FL-
IC121 Vo3a 31 RL FL- 3 FL2
10
IC351 5 FL1 FL+
Q291 PM9009A FL+ 12
PAL007B
TUNL 11 Vo1b 36 FL FL 12
FLIN RL- 23 RL2
9
RL-
MUTE
STBY
Si4L 38 RL RL 14 21 RL1
BUSL+ 1 Vo3b RLIN RL+ RL+
Si1L+ 11
9,10
BUSL- 2 Si1L- Si3L,Si3R
AUBTL 6 FCKSEL 46 22 4 FAN DRIVE
Si2L M972
B.UP CN971 FAN MOTOR
Q972
VER Q282 2 M
1 TX 37
TX
VDD B.UP
PRE-OUTMUTE
Q324
Q971
1 D
FP 2 RX 36
RX 67 CN551(2/2)
AUIMUTE Q391
VDD 8
PW 64 31 BUZZER
IPPW PEE BT3V 9
BZ681 FLAP ILM
B.UP
FLPILM 112
Q853 AMPMUTE BT5V
10
11
E
65
Q351
SYS+B 12 CN76
ASENBO 58
MUTE 13
SYS+B REGULATOR
92 AMPPW Q911
AMPPW
B.UP
Q912
SYSPW SYSPW1
97 BTPW SYS+B
BTPW
DSP3V REGULATOR
3 OELPW 3 IC871 1
OELPW D3V
111 ILMPW NJM2885DL1-33 TUN8V REGULATOR
SYS+B ILMPW
100 DSPPW DAC5V REGULATOR Q921
DSPPW
99 SYSPW 5 IC861 1,3 TUN8V RR RR
SYSPW DAC5V Q922 - +
98 DALMON NJM2872F05
110 DALMON BACK FR FR
BTAV_AUX UP - +
ILL B. FL FL
SYSPW SYSPW1 REM - +
GND ACC RL RL
83 RST2 BT8 - +
82 CN671 BT8V REGULATOR
LRCKOK 135 2 BT5V REGULATOR
ST,BRXEN,BSRQ
KEYAD
KEYD 107 3 WIRED 5 IC566 1,3
Q791 E
REMOTE BT5V
1 CONTROL NJM2872F05 Q792
ATA,BSCK SYSTEM
CONTROLLER BT3V REGULATOR
IC601(2/2) 3 IC561 1
CN811 BT3V
PEG259A NJM2885DL1-33
84 CDRX BTPW
MCKRQ 3
CDTX
4
OEL+B
OEL+B REGULATOR
OEL+B 15 BTPW2 Q841
24 55 9.0V B OEL+B
AUISCK 9.0V Q842
26 54
AUISDO
36 53
AUICS
42 52 61 OELPW
AUIWR FCKSEL
3
9
63
56
AUIBSY
AUIRST
ROT0 125
124
ROT0
ROT1
8 B ILM+B REGULATOR
ROT1 9 Q851
10 DPDT
1 DPDT
6
CN1701 ILM+B
FLPCLS 144 KYDT Q852
KYDT 7
9 SWVDD ILM+B
FLPOPN ILM+B 13
Q831
SWVDD ILMPW
VDD 10
11
12
FOPNSW 2 VDD REGULATOR
FCLSSW SWVDD Q901
13 VDD
Q902
F
FLPPW 137 Q832 DSENS
DSENS 2 Q601
22 RESET SYSPW2
XIN
X601 19 RESET 1 IC661 2
reset VDD DSPPW DSPPW
20MHz 20 XOUT S-80835CNUA-B8U
RST1 SYSPW SYSPW
Q661 5
DALMON DALMON
DEH-P9800BT/XN/EW5
5 6 7 8
17
1 2 3 4
B KEYBOARD UNIT
CN1701
ILM+B
12
OELX
10
B
MULTI-CONTROL
ROT0 Phase_B 10
7
ROT1 89
Phase_A 1 JOYST
8
KD0-2,KS0-2 KEY MATRIX
REMOTE CONTROL S1731,1732,
SENSOR S1734-1739
1 5
IC1801 REM
A OPT IN
GP1UX51RK
3
ILLUMINATION
D1732-1742
CN811
DPDT 30
5 DPDT
KYDT 29
6 KYDT 2
ROMDT
CDRX 34
2 CDRX
CDTX 33 ROMCK 4
3 CDTX
100
OELROMCS
14 DRIVE_CS 1
Vcc1
97
AVcc
14
OEL+B
9V 5V 3.3V 96 OEL CONTROL
Vref
C 3.3V REGULATOR IC1861
S1D13702F00A100
SWVDD5V 5,4 60 D0-15 PD0-5
9 IC1703 1 PDA0-5
Vcc2
S-818A33AUC-BGN
KEY/DISPLAY 22
A0 54 DCLK
1.8V REGULATOR CONTROLLER RS
3
IC1763 LP1A
DSENS 5,1 IC1702 4 4
1 1.8V PEG182A LP2A
NJM2870F18 5
46 CS1 53 GCLKRA
cs1 XCS 6
41 BCLK 45 GCLKGA
BCLK CLK 7
RESET 17 OELRESET 48 GCLKBA
OELRESET XRESET
39
GPSO
RST 9
4 DIS2A
ILLUMINATION
YD 10
47 CS2 OELINT 59
9 cs2 XINT
Q1731 BTLED 44 WRL WRL 56
wr XWR 3.3V
42 RD RD 55
13 rd XRD
Xin 18 FLRESET 5V
FLRESET
X1761
9V
8.0MHz 11 IC1831
Xout PD8161A
D0-15 D0-15
D DATA BUS
A0
A0-19 A0-19
ADDRESS BUS
5V 3V OELGND
IC1762
TC7WH34FU ROM
24 6 2 ROMBK0 13
ROMBK0 A20
23 1 7 ROMBK1 12
ROMBK1 A21
22 3 5 ROMBK2 36
ROMBK2 A22
P2CECS 24
OE1
5V 3V RD 27
IC1764 OE2
ADDRESS BUS
TC7WH32FU
DATA BUS
21 6
P2CE_ON 3 FLASH ROM
5 IC1832
cs0 45 PD6544A
2
7
20 1 D0-15
FLCE_ON
A0-19
FLCECS 26
3V 5V 11
CE
IC1761 WRL
WE
TC7WT125FU RD 28
OELINT 16 6 2 OELINT OE
FLRESET 12
E FLBUSY 19 3 5 FLBUSY FLBUSY 15
RESET
RY/BY
S-RAM
IC1833
M5M5V216ATP-70HI
D0-15
A0-16
WRL 17
WE
RD 41
OE
CS2 6
S
DEH-P9800BT/XN/EW5
18
1 2 3 4
5 6 7 8
E BLUETOOTH UNIT
CODEC
7 TELOUT
15
ANTENNA GSR
F UNIT
3
4
5
BCLK
DR
15 5
ALC
IC51 3 MICIN
BT ANTENNA FS VFTN AN6123MS 17
N2 DATAI 2 IC36
SIOF_RXD DX AK2301A
Q37
OEL MODULE MUTEN 23 BTMUTE
7
CN1931 CN1
ANT1101 Q36
OELX 1 A5
1 22 BTRST
RF_I/O RSTN 6
EEPDO ANT1102
5 2,3
EEPDI Q1
7
EEPSCK
EEPCS
6 G9
VCC_RF
RESETP
Q2
A
ADCS
8 Q2 CN551
9 P1 BTTEST
RST SIOF_SS2 5
2 G8
OL REG_OUT
I1 BTRTS
SCIF1_CTS 4
00 SCIF1_RTS
I2 BTCTS
3
C
PD0-5 17 H2 BTTX
SCIF1_RXD 2
PDA0-5 H3 BTRX
22 SCIF1_TXD 1
22 DCLK E2 ORX
DCLK 16 SCIF0_RXD 40
E3 OTX
3 LS SCIF0_TXD 39
LP1A 15 Q1 BOOTE
4 DTLT BOOT_E 36
LP2A 14 F1 OCTS
5 CKAR SCIF0_CTS 38
GCLKRA 13 F2 ORTS
SCIF0_RTS 37
6 CKAG OSC
GCLKGA 12 CLOCK SELECT
7 CKAB IC21 IC22
GCLKBA 11 TC7PAU04FU Q21
SI2 TC74VHC02FTS1 5
39
GPSO 10 VCC BT3V
11 6 1 BT3V
9 LATCH O1 MCK 4 4A 8
DIS2A 4 SIOF_MCLK 2Y 12
10 D1 4B 3 4 BT3V 9
YD 3 D3V
D3V 10
D5V
D5V 11
L1 HFMCK 2 A8V
3.3V 24 SCO_CLK_OUT 1A A8V 12
3.3V L9 3 X21 11.2896MHz
1B
5V 26 EXTAL OSC
5V IC23
9V TC7PAU04FU Q23
9V 29 5
9V L8 VCC BT3V
30 BRCLK 6 1
PGND 3 4
27
PGND
28 D
GND
23 Q22
GND
25 X22 12.288MHz
OELGND DGND O3 HFAV HFAV
SIOF_SS1
T3 FSCHG
PTB1
DEH-P9800BT/XN/EW5
5 6 7 8
19
1 2 3 4
E CN75
AUX INPUT
IP-BUS:+2.2dBs
C
IP-BUS
8 9 10 11
1 2 3 4
7
5 6
C SYSTEM CONTROLLER
CN902
PEG259A
D
CN901
C
FM(30%):-20.0dBs
AM(30%):-20.0dBs
FM/AM ANTENNA
M801
F M
2 3 1
S1 CLOSE
S2 OPEN
CSN1052
B
CSN1051
FLAP MOTOR
CN1701
XXA7400
D SWITCH UNIT
A 1/2 D
DEH-P9800BT/XN/EW5
20
1 2 3 4
5 6 7 8
A
A-b 1/2
A 2/2 FM:-10.2dBs
A 1/2 TUNER AMP UNIT(MAIN)
AM:-10.2dBs
IP-BUS: +2.3dBs
ER AMP UNIT(DSP) CD: +3.0dBs
SUBWOOFER
R CH
SUBWOOFER
L CH
REAR
R CH
REAR
L CH
FRONT
B
R CH
FRONT
L CH
FM:+3.6dBs
AM:+3.6dBs
IP-BUS: +16.1dBs
CD: +15.8dBs
>
C
FM:-2.4dBs
AM:-2.4dBs
IP-BUS:+10.1dBs
CD: +9.8dBs
FM:23.6dBs
AM:23.6dBs
IP-BUS: 36.1dBs
CD: 35.1dBs
>CEK1136
10A
BACKUP
ROMDATA GND
1K(1/2W)
ILL
B.REM
1K(1/2W)
ACC D
TEL
RL—
FL—
RL+
FL+
RR—
FR—
RR+
FR+
RR RR
- +
BACK FR FR
UP - +
ILL B. FL FL
REM - +
GND ACC RL RL
- +
M972
M
FAN
MOTOR
NOTE :
Symbol indicates a resistor. The > mark found on some component parts indicates Decimal points for resistor
No differentiation is made between chip resistors and the importance of the safety factor of the part. and capacitor fixed values
discrete resistors. Therefore, when replacing, be sure to use parts of are expressed as :
Symbol indicates a capacitor. identical designation. 2.2 ← 2R2
No differentiation is made between chip capacitors and 0.022 ← R022 F
B CN1701 discrete capacitors.
A 1/2
DEH-P9800BT/XN/EW5
5 6 7 8
21
F
E
B
A
D
C
22
A-a A-b
A-b 1/2
1
1
FM:-10.2dBs
A 1/2 TUNER AMP UNIT(MAIN)
AM:-10.2dBs
IP-BUS: +2.3dBs
P) CD: +3.0dBs
SUBWOOFER
R CH
SUBWOOFER
L CH
REAR
R CH
2
2
REAR
L CH
FRONT
R CH
FRONT
L CH
FM:+3.6dBs
AM:+3.6dBs
IP-BUS: +16.1dBs
CD: +15.8dBs
>
DEH-P9800BT/XN/EW5
3
3
1
FM:-2.4dBs
AM:-2.4dBs
IP-BUS:+10.1dBs
CD: +9.8dBs
4
4
FM:23.6dBs
AM:23.6dBs
IP-BUS: 36.1dBs
CD: 35.1dBs
>CEK1136
10A
BACKUP
ROMDATA GND
1K(1/2W)
ILL
B.REM
5
5
1K(1/2W)
ACC
TEL
RL—
FL—
RL+
FL+
RR—
FR—
RR+
FR+
RR RR
- +
BACK FR FR
UP - +
6
6
B. FL FL
ILL REM - +
GND ACC RL RL
- +
DEH-P9800BT/XN/EW5
7
7
M972
M
FAN
MOTOR
3
NOTE :
Symbol indicates a resistor. The > mark found on some component parts indicates Decimal points for resistor
No differentiation is made between chip resistors and the importance of the safety factor of the part. and capacitor fixed values
discrete resistors. Therefore, when replacing, be sure to use parts of are expressed as :
Symbol indicates a capacitor. identical designation. 2.2 ← 2R2
No differentiation is made between chip capacitors and 0.022 ← R022
8
discrete capacitors.
8
A-a A-b
A-b 1/2
23
E
A
D
C
F
B
F
E
B
A
D
C
24
A-a A-b
A-a 1/2
A-b 1/2
1
1
A 2/2
MICROPHONE
TUNER AMP UNIT(DSP)
INPUT
E CN75
2
2
AUX INPUT
DEH-P9800BT/XN/EW5
3
3
IP-BUS:+2.2dBs
IP-BUS
7
8 9 10 11
1 2 3 4
5 6
4
4
C SYSTEM CONTROLLER
C SYSTEM CONTROLLER
CN902
PEG259A
5
5
CN901
C
6
6
FM(30%):-20.0dBs
AM(30%):-20.0dBs
2
DEH-P9800BT/XN/EW5
7
7
FM/AM ANTENNA
M801
2 3 1
M
8
8
FLAP MOTOR B CN1701
CSN1052
S2 OPEN
CSN1051
S1 CLOSE
XXA7400
D SWITCH UNIT
A-a A-b
A-a 1/2 D
A-b 1/2
25
E
A
D
C
F
B
1 2 3 4
A 1/2
A 1/2
A 1/2
A 1/2
F
A 2/2
DEH-P9800BT/XN/EW5
26
1 2 3 4
5 6 7 8
A 1/2
A 2/2
DEH-P9800BT/XN/EW5
5 6 7 8
27
1 2 3 4
REMOTE CONTROL
SENSOR
B
A 1/2 TUNER AMP UNIT(MAIN)
RESET
MULTI-CONTROL
SOURCE DISP
EQ LIST TA
B
DEH-P9800BT/XN/EW5
28
1 2 3 4
5 6 7 8
B KEYBOARD UNIT
DISPLAY
CONTROLLER
LE MXK8230
B
DEH-P9800BT/XN/EW5
5 6 7 8
29
1 2 3 4
A
C-a
C
S
F
C
S
F
B PICKUP UNIT(P10.5)(SERVICE)
$
F
F
T
T
T
F
@
T
F !
F
C T
SWITCHES:
CD CORE UNIT(COMP1D)
S901:HOME SWITCH..........ON-OFF
S903:DSCSNS SWITCH......ON-OFF
S904:12EJ SWITCH.............ON-OFF
S905:8EJ SWITCH...............ON-OFF
The underlined indicates the switch position.
NC
NC
NC
NC
NC
M1 CXC6742 CD DRIVER NC
NC
SPINDLE MOTOR
NC
S
NC
S NC
NC
C NC
# NC
C
NC
NC
M2 CXC4026 T S NC
LOADING/CARRIAGE MOTOR
NC
8 6 NC
F C NC
7
9
E
4
NC
NC
F
F
3 T
T
2
C
C
S
S
C
DEH-P9800BT/XN/EW5
30
1 2 3 4
5 6 7 8
A
C-b
SIGNAL LINE B
F
FOCUS SERVO LINE
T
TRACKING SERVO LINE
C
CARRIAGE SERVO LINE
S
SPINDLE SERVO LINE
C CD CORE UNIT(COMP1D)
0
+ 3.3 V REGULATOR
C
A 1/2 CN702
D
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC CD3VON(MCKRQ)
NC SRAMLEVEL2
NC
NC ADENA
NC
NC
NC
NC
NC
NC
NC SRAMLEVEL1
PE5552A SRAMLEVEL0
5
(S904)
E
CD CONTROLLER (S905)
NC
NC
)
NC
¤
⁄
*
&
A 1/2 CN701
C
DEH-P9800BT/XN/EW5
5 6 7 8
31
F
E
B
A
D
C
32
C-a C-b
C-b
1
1
2
2
SIGNAL LINE
F
FOCUS SERVO LINE
T
TRACKING SERVO LINE
C
CARRIAGE SERVO LINE
S
SPINDLE SERVO LINE
C CD CORE UNIT(COMP1D)
0
DEH-P9800BT/XN/EW5
3
3
+ 3.3 V REGULATOR
4
4
A 1/2 CN702
A 1/2 CN702
5
5
2
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC CD3VON(MCKRQ)
NC SRAMLEVEL2
NC
NC ADENA
NC
6
6
NC
NC
NC
NC
NC
NC SRAMLEVEL1
PE5552A SRAMLEVEL0
5
(S904)
CD CONTROLLER (S905)
NC
NC
NC
DEH-P9800BT/XN/EW5
¤
7
7
⁄
*
&
A 1/2 CN701
3
8
8
C-a C-b
C-b
33
E
A
D
C
F
B
F
E
B
A
D
C
34
C-a
A-a C-b
C-a
C-b
1
1
T
F
S
C
1
T
F
S
C
2
2
PICKUP UNIT(P10.5)(SERVICE)
$
DEH-P9800BT/XN/EW5
F
F
T
T
3
3
T
F
@
T
F !
F
T
4
4
SWITCHES:
CD CORE UNIT(COMP1D)
S901:HOME SWITCH..........ON-OFF
S903:DSCSNS SWITCH......ON-OFF
S904:12EJ SWITCH.............ON-OFF
S905:8EJ SWITCH...............ON-OFF
5
2
NC
NC
NC
NC
NC
M1 CXC6742 CD DRIVER NC
SPINDLE MOTOR
NC
S
NC
S NC
NC
C NC
# NC
6
6
C
NC
NC
M2 CXC4026 T S NC
LOADING/CARRIAGE MOTOR
NC
8 6 NC
F C NC
7
9
4
NC
NC
F
F
3 T
T
DEH-P9800BT/XN/EW5
2
7
7
S
S
C
C
1
3
8
8
C-a
A-a C-b
C-a
C-b
35
E
A
D
C
F
B
1 2 3 4
- Waveforms Note : 1. The encircled numbers denote measuring points in the circuit diagram.
2. Reference voltage REFO1(1.65 V)
A
1 DSCSNS 5 V/div 500 ms/div 1 DSCSNS 5 V/div 500 ms/div 1 DSCSNS 5 V/div 500 ms/div
2 8SNS 5 V/div 4 CLCONT 5 V/div 2 8SNS 5 V/div
3 12SNS 5 V/div 5 VD 10 V/div 3 12SNS 5 V/div
12 cm CD-DA setup operation after loading 12 cm CD-ROM(1 session) setup operation 12 cm CD-ROM(3 sessions) setup operation
after loading after loading
9 FIN 200 mV/div 500 ms/div ! TE 500 mV/div 200 ms/div @ FE 500 mV/div 20 ms/div
0 RFOK 2 V/div @ FE 500 mV/div 9 FIN 500 mV/div
6 SIN 2 V/div ! TE 500 mV/div
8 TIN 500 mV/div
12 cm CD-DA Source On setup operation Source On setup operation CD-DA Play operation
D
DEH-P9800BT/XN/EW5
36
1 2 3 4
5 6 7 8
9 FIN 500 mV/div 200 ms/div ! TE 500 mV/div 2 ms/div $ RFAGC 1 V/div 500 µs/div
@ FE 500 mV/div $ RFAGC 500 mV/div ! TE 500 mV/div A
8 TIN 500 mV/div
$ RFAGC 1 V/div 500 µs/div $ RFAGC 1 V/div 1 ms/div $ RFAGC 1 V/div 2 ms/div
! TE 500 mV/div ! TE 500 mV/div ! TE 500 mV/div
8 TIN 500 mV/div 8 TIN 500 mV/div 8 TIN 500 mV/div
$ RFAGC 1 V/div 200 ms/div 1 DSCSNS 5 V/div 500 ms/div 1 DSCSNS 5 V/div 500 ms/div
! TE 1 V/div 2 8SNS 5 V/div 5 CLCONT 5 V/div
7 CIN 500 mV/div 3 12SNS 5 V/div 4 LOEJ 5 V/div
6 SIN 2 V/div
Search operation(Outter to Inner) 12 cm CD Eject operation 12 cm CD Eject operation
D
Ref.: Ref.: Ref.:
REFO GND GND
1 DSCSNS 5 V/div 500 ms/div 6 SIN 1 V/div 500 ms/div 6 SIN 1 V/div 500 ms/div
2 8SNS 5 V/div 7 CIN 500 mV/div 7 CIN 500 mV/div
3 12SNS 5 V/div 8 TIN 500 mV/div 8 TIN 500 mV/div
E
8 cm CD Eject operation CD-DA → CD-ROM mode change(Band key) CD-ROM → CD-DA mode change(Band key)
DEH-P9800BT/XN/EW5
5 6 7 8
37
1 2 3 4
$ RFAGC 1 V/div 500 µs/div ( CD3VON 5 V/div 200 ms/div ⁄ DOUT 2 V/div 20 µs/div
A 8 TIN 1 V/div & LRCK 2 V/div & LRCK 2 V/div
! TE 1 V/div ) LRCKOK 2 V/div * BCK 2 V/div
9 FIN 1 V/div
Black dot(800 µm) during play 12 cm CD Eject operation CD-DA play operation
Ref.: Ref.:
REFO GND
C
Mode: Mode:
Normal Normal
DEH-P9800BT/XN/EW5
38
1 2 3 4
5 6 7 8
DEH-P9800BT/XN/EW5
5 6 7 8
39
1 2 3 4
COMPOUND UNIT
F
F ANTENNA UNIT
E F
DEH-P9800BT/XN/EW5
40
1 2 3 4
5 6 7 8
E BLUETOOTH UNIT
A 1/2 CN551
E
DEH-P9800BT/XN/EW5
5 6 7 8
41
1 2 3 4
110
C 100
90
80
70
D
60
50
E CN76
40
E
30
20
10
Y
F
0 X 10 20 30 40 50 60 70 80
A
DEH-P9800BT/XN/EW5
42
1 2 3 4
5 6 7 8
A
M972 FAN MOTOR SIDE A
CORD ASSY
CORD ASSY (PRE OUTPUT) ANTENNA CABLE
(POWER SUPPLY,SPEAKER)
2 1 3
5 3 1
6 4 2
12 10 8 6 4 2
B
C CN902
D
E
M801
FLAP MOTOR
C CN901
2 4 6 8 10 12 14 16 18
1 3 5 7 9 11 13 15 17
B CN1701
F
70 80 90 100 110 120 130 140 150 160 170 180
FRONT
A
DEH-P9800BT/XN/EW5
5 6 7 8
43
1 2 3 4
A
A TUNER AMP UNIT
C-
PCL
TESTIN
A
DEH-P9800BT/XN/EW5
44
1 2 3 4
5 6 7 8
A
SIDE B
150
140
B
130
120
110
100 C
90
80
70
D
60
50
40
E
30
20
10
Y
F
80 70 60 50 40 30 20 10 X 0
A
DEH-P9800BT/XN/EW5
5 6 7 8
45
1 2 3 4
A
B KEYBOARD UNIT
PHONE LIST
40
MULTI-CONTROL
EQ DISP TA
2 7
30
5
B
8 10
1 4
20 6
9
3
10
SOURCE BAND/ESC
OPEN/EJECT
C
Y
X
0 10 20 30 40 50 60 70 80
B KEYBOARD UNIT
0 10 20 30 40 50 60 70 80
X
D
10
20
30
40
B
DEH-P9800BT/XN/EW5
46
1 2 3 4
5 6 7 8
SIDE A
A
RESET
SIDE B
OEL MODULE
F
A CN811
B
DEH-P9800BT/XN/EW5
5 6 7 8
47
1 2 3 4
CN702
A
CN701
REFO1
E
20
HOME
CN901
D
M2
LOADING
/CARRIAGE
MOTOR
M1
E
SPINDLE
MOTOR
IC203 IC301
C
DEH-P9800BT/XN/EW5
48
1 2 3 4
5 6 7 8
8EJ
12EJ
B
DSCSNS
C
DEH-P9800BT/XN/EW5
5 6 7 8
49
1 2 3 4
A
E BLUETOOTH UNIT SIDE A
A CN551
40
C
30
20
D
10
0 X 10 20 30
E
DEH-P9800BT/XN/EW5
50
1 2 3 4
5 6 7 8
40
C
30
20
D
10
30 20 10 X 0
F ANT1102
F
E
DEH-P9800BT/XN/EW5
5 6 7 8
51
1 2 3 4
A
F ANTENNA UNIT SIDE A
E CN1
BT ANTENNA
F
DEH-P9800BT/XN/EW5
52
1 2 3 4
5 6 7 8
D SWITCH UNIT
A CN801
1 2 3
CLOSE
OPEN
D
DEH-P9800BT/XN/EW5
5 6 7 8
53
1 2 3 4
E
R 9 (A,32,20) RS1/16S103J
R 21 (A,33,39) RS1/16S101J
Unit Number : CWN1771 R 22 (B,21,38) RS1/16S473J
Unit Name : Bluetooth Unit R 23 (A,23,37) RS1/16S473J
R 24 (B,24,40) RS1/16S101J
MISCELLANEOUS R 25 (A,24,40) RS1/16S101J
R 26 (A,21,41) RS1/16S332J
IC 21 (A,29,43) IC TC74VHC02FTS1
IC 22 (A,23,43) IC TC7PAU04FU R 27 (A,21,43) RS1/16S105J
IC 23 (B,22,40) IC TC7PAU04FU R 28 (B,20,43) RS1/16S332J
IC 36 (A,11,14) IC AK2301A R 29 (B,20,40) RS1/16S105J
E IC 51 (A,16,27) IC AN6123MS R 36 (A,15,5) RS1/16S103J
R 37 (A,14,7) RS1/16S104J
IC 56 (B,10,13) IC PCM1742KE
IC 66 (B,12,21) IC NJM4558V R 41 (A,8,22) RS1/16S103J
Q 1 (A,30,13) Transistor DTC124EUA R 43 (A,10,21) RS1/16S393J
Q 2 (A,34,29) Transistor DTC124EUA R 44 (A,8,20) RS1/16S393J
Q 21 (B,27,40) Transistor UMD2N R 45 (A,14,21) RAB4C101J
R 46 (A,4,18) RS1/16S103J
Q 22 (B,31,43) Transistor DTC124EUA
Q 23 (B,27,43) Transistor UMD2N R 47 (A,16,15) RS1/16S203J
Q 36 (A,17,8) Transistor DTC124EUA R 48 (A,18,18) RS1/16S103J
Q 37 (A,16,12) Transistor DTC124EUA R 49 (A,7,8) RS1/16S203J
L 1 (A,23,24) Inductor CTF1394 R 50 (A,14,8) RS1/16S473J
F R 51 (A,20,28) RS1/16S105J
L 21 (A,26,39) Inductor CTF1379
L 22 (A,23,40) Inductor CTF1379 R 52 (A,7,5) RS1/16S103J
L 23 (B,23,44) Inductor CTF1379 R 57 (B,15,15) RAB4C101J
DEH-P9800BT/XN/EW5
54
1 2 3 4
5 6 7 8
Circuit Symbol and No. Part No. Circuit Symbol and No. Part No.
R 58 (A,30,36) RS1/16S821J C 60 (B,10,7) CKSYB106K6R3
R 66 (B,18,21) RS1/16S103J C 61 (B,14,6) CKSRYB102K50
R 67 (B,16,24) RS1/16S103J C 66 (B,16,18) CKSYB475K16
A
R 68 (B,12,19) RS1/16S473J C 67 (B,9,17) CKSYB475K16
R 69 (B,11,24) RS1/16S103J C 68 (B,16,21) CCSRCH221J50
R 70 (B,7,24) RS1/16S103J C 69 (B,16,26) CCSRCH391J50
R 71 (B,9,19) RS1/16S473J C 70 (B,9,26) CKSYB106K6R3
R 72 (B,3,17) RS1/16S103J C 71 (B,6,25) CKSRYB105K10
R
79
80
(B,11,32)
(A,3,33)
RS1/16S0R0J
RS1/16S101J
A
Unit Number : CWN1435 B
R 81 (B,10,29) RS1/16S101J
R 82 (B,16,29) RS1/16S101J
Unit Name : Tuner Amp Unit
R 83 (B,9,32) RS1/16S101J
R 84 (B,16,31) RS1/16S0R0J MISCELLANEOUS
DEH-P9800BT/XN/EW5
5 6 7 8
55
1 2 3 4
Circuit Symbol and No. Part No. Circuit Symbol and No. Part No.
Q 301 (A,104,84) Transistor UMH3N D 551 (B,54,59) Diode DAN202U
Q 321 (A,154,131) Transistor IMH23 D 601 (B,121,61) Diode DAN202U
Q 322 (A,148,127) Transistor IMH23 D 671 (B,19,140) Diode DAN202U
A
Q 323 (A,139,127) Transistor IMH23 D 672 (B,24,140) Diode DAP202U
Q 324 (A,144,114) Transistor UMD3N D 721 (A,30,72) Diode HZS9L(A2)
Q 351 (A,125,124) Transistor DTC124EUA D 751 (B,135,51) Diode Network DA204U
Q 391 (A,39,58) Transistor 2SC4081 D 752 (B,126,39) Diode Network DA204U
Q 401 (A,160,101) Transistor UMH1N D 791 (B,110,73) Diode HZU6L(B1)
DEH-P9800BT/XN/EW5
56
1 2 3 4
5 6 7 8
Circuit Symbol and No. Part No. Circuit Symbol and No. Part No.
L 604 (A,139,90) Ferri-Inductor LAU100K R 181 (A,102,130) RS1/16S104J
L 701 (A,101,27) Inductor LCTAW2R2J3225 R 182 (B,110,125) RS1/16S683J
L 831 (A,76,17) Ferri-Inductor LAU100K R 183 (A,98,130) RS1/16S153J
A
L 841 (A,57,18) Inductor LAU2R2K R 184 (B,116,125) RS1/16S682J
L 872 (A,41,85) Inductor CTF1617 R 185 (A,104,124) RS1/16S152J
L 951 (A,86,115) Inductor LAU2R2K R 186 (A,104,130) RS1/16S222J
X 201 (A,59,91)Crystal Resonator 16.934 4 MHz CSS1052 R 187 (A,105,130) RS1/16S561J
X 371 (A,87,107)Ceramic Resonator 4.096 MHz CSS1429 R 188 (A,110,130) RS1/16S473J
DEH-P9800BT/XN/EW5
5 6 7 8
57
1 2 3 4
Circuit Symbol and No. Part No. Circuit Symbol and No. Part No.
R 294 (A,98,76) RS1/16S682J R 447 (A,40,121) RS1/16S103J
R 295 (A,101,71) RS1/16S682J R 448 (A,40,119) RS1/16S103J
R 296 (A,101,76) RS1/16S682J R 449 (A,39,123) RS1/16S103J
A
R 297 (B,100,68) RS1/16S102J R 450 (A,52,122) RS1/16S103J
R 298 (B,103,71) RS1/16S102J R 451 (A,45,116) RS1/16S104J
R 299 (B,102,74) RS1/16S101J R 452 (A,47,117) RS1/16S104J
R 300 (B,89,70) RS1/16S101J R 501 (B,95,24) RS1/16S681J
R 301 (A,98,83) RS1/16S473J R 502 (B,95,26) RS1/16S681J
DEH-P9800BT/XN/EW5
58
1 2 3 4
5 6 7 8
Circuit Symbol and No. Part No. Circuit Symbol and No. Part No.
R 706 (B,108,49) RS1/16S221J R 852 (B,59,20) RS1/4SA391J
R 707 (B,96,49) RS1/16S221J R 853 (A,134,34) RS1/16S562J
R 708 (B,108,47) RS1/16S221J R 854 (A,132,37) RS1/16S103J
A
R 709 (B,96,45) RS1/16S221J R 855 (A,89,16) RS1/16S151J
R 710 (B,108,45) RS1/16S681J R 901 (B,22,56) RS1/16S223J
R 711 (B,106,40) RS1/16S473J R 902 (A,36,50) RS1/16S272J
R 712 (A,116,69) RS1/16S104J R 911 (A,22,116) RS1/16S821J
R 721 (B,24,65) RS1/4SA391J R 921 (B,16,85) RS1/16S821J
DEH-P9800BT/XN/EW5
5 6 7 8
59
1 2 3 4
Circuit Symbol and No. Part No. Circuit Symbol and No. Part No.
C 181 (A,100,130) CCSRCH681J50 C 297 (B,89,76) CKSRYB104K16
C 182 (A,105,124) CKSQYB225K10 C 301 (A,98,80) CCSRCH681J50
C 183 (A,111,123) CEJQ101M6R3 C 302 (A,98,88) CCSRCH681J50
A C 201 (B,54,81) CKSRYB104K16 C 303 (A,101,83) CCSRCH331J50
C 202 (B,56,82) CKSRYB682K50 C 304 (A,101,85) CCSRCH331J50
DEH-P9800BT/XN/EW5
60
1 2 3 4
5 6 7 8
Circuit Symbol and No. Part No. Circuit Symbol and No. Part No.
C 554 (A,46,63) CEJQ330M10 C 851 (B,65,15) CKSRYB473K25
C 560 (B,46,54) CKSRYB102K50 C 852 (A,92,14) CKSRYB104K16
C 561 (A,51,66) CEJQ220M16 C 861 (A,61,97) CKSRYB105K6R3
C 562 (B,63,43) CKSRYB103K50 C 862 (A,61,99) CKSRYB103K50 A
C 563 (B,63,33) CKSYB475K10 C 863 (A,68,98) CKSRYB104K16
C
C
762
763
(B,118,45)
(B,119,49)
CKSRYB472K50
CKSRYB102K50
B
Unit Number :
D
DEH-P9800BT/XN/EW5
5 6 7 8
61
1 2 3 4
Circuit Symbol and No. Part No. Circuit Symbol and No. Part No.
R 1750 (B,12,17) RS1/16S271J
D 1735 (A,50,9) LED SML412BC5T(MN)
D 1736 (A,67,34) LED SML412BC5T(MN) R 1751 (B,11,17) RS1/16S331J
A D 1737 (A,67,14) LED SML412BC5T(MN) R 1752 (B,11,11) RS1/16S561J
D 1738 (A,33,34) LED SML412BC5T(MN) R 1753 (B,10,11) RS1/16S331J
D 1739 (A,33,14) LED SML412BC5T(MN) R 1761 (A,100,35) RS1/16S473J
R 1762 (A,97,31) RS1/16S473J
D 1740 (A,17,24) LED SML412BC5T(MN)
D 1741 (A,9,11) LED SML412BC5T(MN) R 1763 (A,98,29) RS1/16S682J
D 1751 (B,40,16) Diode HZU7R5(B2) R 1764 (A,103,29) RS1/16S682J
D 1752 (B,66,17) Diode DAP202U R 1765 (A,104,33) RS1/16S154J
D 1753 (B,66,22) Diode DAN202U R 1766 (A,101,29) RS1/16S392J
R 1767 (A,99,29) RS1/16S392J
D 1759 (B,36,16) Diode HZU7R5(B2)
D 1761 (A,103,36) Diode 1SS355 R 1768 (A,107,33) RS1/16S473J
L 1701 (B,121,19) Inductor CTF1379 R 1769 (B,108,22) RAB4CQ101J
B L 1702 (B,124,21) Inductor CTF1379 R 1770 (B,108,31) RAB4CQ101J
L 1703 (B,143,23) Inductor CTF1617 R 1771 (A,101,33) RS1/16S473J
R 1772 (B,108,28) RS1/16S101J
L 1762 (B,144,16) Inductor CTF1617
L 1861 (B,159,19) Inductor CTF1617 R 1773 (B,107,37) RS1/16S101J
L 1862 (A,113,14) Inductor LCTC1R0K2125 R 1775 (B,79,7) RAB4CQ101J
L 1863 (A,126,7) Inductor LCTC1R0K2125 R 1776 (B,105,37) RS1/16S101J
L 1931 (B,122,11) Inductor CTF1617 R 1777 (A,86,37) RAB4CQ473J
R 1778 (A,91,31) RS1/16S101J
L 1932 (B,123,15)Chip Ferrite Bead CTF1399
L 1933 (B,149,15) Inductor ATH1167 R 1779 (A,92,35) RS1/16S473J
X 1761 (A,109,27)Resonator 8.0 MHz CSS1675 R 1780 (A,91,33) RS1/16S101J
S 1701 (A,163,6) Push Switch CSG1155 R 1781 (B,99,37) RAB4CQ101J
C S 1731 (A,8,27) Push Switch CSG1155 R 1782 (B,99,16) RS1/16S473J
R 1783 (B,97,16) RS1/16S473J
S 1732 (A,35,39) Push Switch CSG1155
S 1733 (A,50,24)Switch(MULTI-CONTROL) CSX1065 R 1784 (B,95,16) RS1/16S101J
S 1734 (A,35,9) Push Switch CSG1155 R 1785 (A,83,34) RAB4CQ101J
S 1735 (A,65,39) Push Switch CSG1155 R 1786 (B,82,35) RAB4CQ101J
S 1736 (A,65,9) Push Switch CSG1155 R 1787 (B,85,33) RAB4CQ101J
R 1789 (B,85,16) RAB4CQ101J
S 1737 (A,17,27) Push Switch CSG1155
S 1738 (A,6,11) Push Switch CSG1155 R 1790 (B,80,18) RS1/16S101J
S 1739 (A,26,27) Push Switch CSG1155 R 1791 (B,80,16) RS1/16S101J
OEL Module MXK8230 R 1793 (B,82,31) RAB4CQ101J
R 1794 (B,85,28) RAB4CQ101J
D RESISTORS R 1795 (B,82,27) RAB4CQ101J
DEH-P9800BT/XN/EW5
62
1 2 3 4
5 6 7 8
Circuit Symbol and No. Part No. Circuit Symbol and No. Part No.
R 1932 (B,112,16) RS1/16S101J Unit Number : CWX3328
R 1933 (B,109,16) RS1/16S101J Unit Name : CD Core Unit(COMP1D)
R 1934 (B,107,16) RAB4CQ101J A
MISCELLANEOUS
CAPACITORS
IC 201 (B,39,70) IC UPD63763CGJ
C 1707 (B,129,21) CKSRYB474K10 IC 203 (A,12,16) IC NJM2886DL3-33
C 1708 (B,143,30) CKSRYB474K10 IC 301 (A,28,18) IC BA5835FP
C 1709 (B,148,32) CKSRYB223K50 IC 701 (A,32,48) IC PE5552A
C 1710 (B,137,15) CSZS4R7M10 Q 101 (B,60,89) Transistor 2SA1577
C 1711 (B,151,30) CSZS4R7M10
Q 701 (B,24,41) Transistor UN2111
C 1732 (A,67,24) CKSRYB104K16 X 701 (A,24,37)Ceramic Resonator 4.000 MHz CSS1652
C 1735 (A,34,24) CKSRYB104K16 S 901 (A,57,57) Switch(HOME) CSN1067
C 1739 (A,10,35) CKSRYB104K16 S 903 (B,23,78) Switch(DSCSNS) CSN1067
C 1741 (A,50,40) CKSRYB104K16 S 904 (B,42,87) Switch(12EJ) CSN1068 B
C 1744 (A,50,7) CKSRYB104K16
S 905 (B,28,88) Switch(8EJ) CSN1068
C 1746 (A,16,20) CKSRYB104K16
C 1747 (A,11,11) CKSRYB104K16 RESISTORS
C 1748 (B,62,26) CKSRYB103K50
C 1749 (B,35,33) CKSRYB103K50 R 101 (B,61,92) RS1/10SR2R4J
C 1750 (A,67,32) CKSRYB104K16 R 102 (B,63,92) RS1/10SR2R4J
R 103 (B,63,89) RS1/10SR2R7J
C 1751 (A,67,15) CKSRYB104K16 R 104 (A,52,73) RS1/16SS102J
C 1752 (A,33,32) CKSRYB104K16 R 201 (B,44,57) RS1/16SS102J
C 1753 (A,33,15) CKSRYB104K16
C 1761 (A,97,37) CKSRYB104K16 R 202 (A,38,62) RS1/16SS473J
C 1762 (A,101,37) CKSRYB104K16 R 203 (A,37,62) RS1/16SS473J C
R 210 (A,33,62) RS1/16SS0R0J
C 1763 (A,101,35) CKSRYB473K25 R 214 (A,46,79) RS1/16SS472J
C 1764 (A,135,38) CKSRYB104K16 R 216 (A,46,81) RS1/16SS472J
C 1765 (B,103,37) CKSRYB103K50
C 1766 (B,141,16) CKSRYB104K16 R 221 (A,44,81) RS1/16SS103J
C 1767 (B,90,18) CKSRYB104K16 R 222 (A,45,81) RS1/16SS103J
R 225 (B,52,78) RS1/16SS103J
C 1768 (B,135,11) CKSRYB103K50 R 226 (B,52,77) RS1/16SS393J
C 1769 (B,140,11) CSZS4R7M10 R 227 (A,44,75) RS1/16SS562J
C 1770 (A,126,34) CKSRYB104K16
C 1801 (B,22,34) CSZS100M16 R 228 (A,46,72) RS1/16SS122J
C 1831 (A,148,26) CKSRYB104K16 R 229 (A,44,72) RS1/16SS472J
R 232 (A,46,75) RS1/16SS122J D
C 1832 (A,96,11) CKSRYB104K16 R 237 (B,22,64) RS1/16SS221J
C 1833 (B,161,40) CKSRYB104K16 R 238 (B,22,65) RS1/16SS221J
C 1834 (A,156,15) CCSRCH100D50
C 1835 (B,139,13) CCSRCH100D50 R 239 (B,22,66) RS1/16SS221J
C 1862 (B,159,16) CKSRYB103K50 R 241 (B,26,63) RS1/16SS333J
R 243 (B,26,62) RS1/16SS333J
C 1863 (B,161,10) CSZS4R7M10 R 245 (B,26,69) RS1/16SS333J
C 1864 (A,114,14) CKSRYB104K16 R 248 (B,55,74) RS1/16SS105J
C 1865 (A,132,15) CKSRYB473K25
C 1867 (A,117,27) CKSRYB104K16 R 307 (A,19,20) RS1/16SS183J
C 1868 (A,132,25) CKSRYB104K16 R 308 (A,17,20) RS1/16SS183J
R 309 (A,18,18) RS1/16SS183J
C 1869 (A,130,11) CKSRYB104K16 R 310 (A,17,16) RS1/16SS183J E
C 1870 (A,132,13) CKSRYB104K16 R 701 (B,26,44) RS1/16SS221J
C 1871 (A,126,29) CCSRCH100D50
C 1872 (A,130,30) CCSRCH100D50 R 707 (B,32,45) RS1/16SS473J
C 1873 (A,132,24) CCSRCH100D50 R 709 (A,36,35) RS1/16SS222J
R 710 (B,41,46) RS1/16SS102J
C 1874 (A,109,14) CKSYB106K10 R 712 (A,45,57) RS1/16SS222J
C 1932 (B,118,11) CKSRYB103K50 R 713 (B,40,57) RS1/16SS222J
C 1933 (B,117,13) CKSRYB104K16
C 1936 (B,117,15) CKSRYB104K16 R 716 (B,29,37) RS1/16SS472J
C 1937 (B,93,11) CKSRYB104K16 R 724 (B,31,36) RS1/16S473J
R 726 (B,23,47) RS1/16SS103J
C 1939 (B,154,15) CKSYB106K10 R 727 (B,31,42) RS1/16SS473J
C 1941 (B,131,8) CKSYB106K10 R 729 (B,20,48) RS1/16SS223J F
C R 730
R 740
(B,20,46)
(A,38,59)
RS1/16SS473J
RS1/16SS222J
DEH-P9800BT/XN/EW5
5 6 7 8
63
1 2 3 4
Circuit Symbol and No. Part No. Circuit Symbol and No. Part No.
R 746 (A,13,38) RS1/16SS104J M 801 Motor Unit(FLAP) XXA7400
R 750 (A,40,66) RS1/16SS473J
R 751 (B,40,46) RS1/16SS102J
A
R 902 (A,20,36) RS1/16SS221J
R 905 (A,21,36) RS1/16SS221J
R 906 (B,20,36) RS1/16SS221J
R 909 (B,16,65) RS1/16SS0R0J
CAPACITORS
D
Unit Number : CWS1389
Unit Name : Switch Unit
S 1 Switch(CLOSE) CSN1051
S 2 Switch(OPEN) CSN1052
DEH-P9800BT/XN/EW5
64
1 2 3 4
5 6 7 8
6. ADJUSTMENT
6.1 DISPLAY TEST MODE
- Display Test Mode A
Service mode,
BT Test Mode Service Mode
Screen-still mode, B
or BT test mode
[PHONE] + [BAND] key [EQ] + [TA] key
DEH-P9800BT/XN/EW5
5 6 7 8
65
1 2 3 4
6.2 CD ADJUSTMENT
DEH-P9800BT/XN/EW5
66
1 2 3 4
5 6 7 8
- Flow Chart
[Key] [EQ] + [TA] + Reset or
[EQ] + [TA] + BU + ACC
Contents Test Mode In
*6 C
[BAND] [2]
Power Off Tracking Open
*) • After the [Eject] key is pressed keys other than the [Eject] key should not be pressed, until disc ejection is complete.
• When the key [2] or [3] is pressed during the Focus Search, the power supply should be immediately turned off (otherwise the lens
sticks to Wall, causing the actuator to be damaged).
• In the case of TR jump other than to 100TR, the function shall continue to be processed even if the TR jump key is released. As for F
the CRG Move and 100TR Jump, the mechanism shall be set to the Tracking Close mode when the key is released.
• When the power is turned on/off the jump mode is reset to the Single TR (91) while the gain of the RFAMP is reset to 0 dB. At the
same time all the self-adjusting values shall return to the default setting.
DEH-P9800BT/XN/EW5
5 6 7 8
67
1 2 3 4
• Note :
The grating angle of the PU unit cannot be adjusted after the PU unit is changed. The PU unit in the CD mechanism
module is adjusted on the production line to match the CD mechanism module and is thus the best adjusted PU
unit for the CD mechanism module. Changing the PU unit is thus best considered as a last resort. However, if the
PU unit must be changed, the grating should be checked using the procedure below.
• Purpose :
To check that the grating is within an acceptable range when the PU unit is changed.
B • Symptoms of Mal-adjustment :
If the grating is off by a large amount symptoms such as being unable to close tracking, being unable to perform
track search operations, or taking a long time for track searching.
• Method :
• Measuring Equipment • Oscilloscope, Two L.P.F.
• Measuring Points • E, F, REFO1
• Disc • TCD-782
• Mode • TEST MODE
CD CORE UNIT(COMP1D)
C
L.P.F.
REFO1
E Xch Ych
E 100kΩ
F
Oscilloscope
VREF 390pF
F 100kΩ
VREF 390pF
D L.P.F.
• Checking Procedure
1. In test mode, load the disc and switch the 3 V regulator on.
2. Using the → and ← buttons, move the PU unit to the innermost track.
3. Press key 3 to close focus, the display should read "91". Press key 2 to implement the tracking balance
adjustment the display should now read "81". Press key 3. The display will change, returning to "81" on the
fourth press.
4. As shown in the diagram above, monitor the LPF outputs using the oscilloscope and check that the phase
E
difference is within 75° . Refer to the photographs supplied to determine the phase angle.
5. If the phase difference is determined to be greater than 75° try changing the PU unit to see if there is any
improvement. If, after trying this a number of times, the grating angle does not become less than 75° then the
mechanism should be judged to be at fault.
• Note
Because of eccentricity in the disc and a slight misalignment of the clamping center the grating waveform may be
seen to "wobble" ( the phase difference changes as the disc rotates). The angle specified above indicates the
average angle.
• Hint
Reloading the disc changes the clamp position and may decrease the "wobble".
DEH-P9800BT/XN/EW5
68
1 2 3 4
5 6 7 8
0° 30°
45° 60°
75° 90°
DEH-P9800BT/XN/EW5
5 6 7 8
69
1 2 3 4
DEH-P9800BT/XN/EW5
70
1 2 3 4
5 6 7 8
A
- PCL Output
In the normal operation mode (with the detachable panel installed, the ACC switched ON, the standby mode
cancelled), shift the TESTIN IC601(Pin 126) terminal to H.
The clock signal is output from the PCL terminal IC601(Pin 62).
The frequency of the clock signal is 625.000 kHz that is one 32nd of the fundamental frequency.
The clock signal should be 625.000 kHz(- 25 Hz, + 25 Hz).
If the clock signal is out of the range, the X'tal (X601) should be replaced with the new one.
- Connection Diagram
C
4.7 µF/16 V
+
Audio Oscillator
BU
Acc
D
+12 V
DC Regulated
Power Supply GND
ACC Line
HPF
To microcomputer
F
F/V IC
DEH-P9800BT/XN/EW5
5 6 7 8
71
1 2 3 4
A
- Connection Diagram
Frequency
Counter
Pin 49(C-)
B
R135
VR121
IC121
E.VOL IC oscillating frequency adjustment when you change the VR121, R135 or IC121.
- E.VOL IC Oscillating Frequency Adjustment
DEH-P9800BT/XN/EW5
72
1 2 3 4
5 6 7 8
DEH-P9800BT/XN/EW5
5 6 7 8
73
1 2 3 4
- Function Specifications for Bluetooth Test Mode (when using BT-compliant mobile phone)
Specifications for BT Built-in mobile phone
The mobile phone compliant to Bluetooth Ver 1.1 requires at least *HFP and *OPP to be mounted.
A The model having validly accomplished connecting verification is desirable.
The model capable of being in standby state is desirable.
*HFP : Hands-Free Profile, OPP : Object Push Profile
1. Cautions
[Important]
* When conducting this Test Mode, writing into memory and others will be checked. Because of that, the data stored by the
user will be deleted. Please obtain approval from the user beforehand.
* On this product, the user's memory for telephone directory information will not be cleared even if BU power is turned off.
If you register the telephone information to the unit in normal mode for checking the Bluetooth function, you
B have to delete the data which you registered before returning the unit to the user.
* Note that if the user is already useing all of user's memory(No.1 - 3 and Guest 1,2), you need to delete user's data in
order to check the Bluetooth function in normal mode.
2. Outline of Functions
The following 3 items are to be confirmed for the simple BT action check by using BT-compliant mobile phone:
• Confirmation of Bluetooth connection (certification connection and voice connection)
• Confirmation of BT antenna sensitivity (connection)
• Confirmation of FLASH memory action
C
3. Configuration Diagram
DEH-P9800BT/XN/EW5
Bluetooth
DEH-P9800BT/XN/EW5
74
1 2 3 4
5 6 7 8
↓ Center key
- B T & F L A S H T E S T -
TEST D
* * * * * * * *
A N T E N N A : - 3 5
S O U N D S T A T E : O F F
F L A S H M E M O R Y :
↓ Center key
- B T & F L A S H T E S T -
TEST
Start FLASH check.
* * * * * * * *
A N T E N N A : - 3 5
S O U N D S T A T E : O F F
F L A S H M E M O R Y : C H K
E
↓ FLASH check complete
- B T & F L A S H T E S T - FLASH check is conducted automatically according to the followi-
TEST ng steps.
Delete Write Read Totally delete Read
↓
* * * * * * * *
A N T E N N A : - 3 5 Read out the written data, and verify that both of them match.
S O U N D S T A T E : O F F Read out after total delete, and verify that the deletion has been
F L A S H M E M O R Y : O K accomplished. Verification is OK if OK is displayed.
Test is complete if everything progressed normally up to this point.
DEH-P9800BT/XN/EW5
5 6 7 8
75
1 2 3 4
- Function Specifications for Bluetooth Test Mode (when using 2.4 GHz-compliant spectrum analyzer)
1. Cautions
* When the service site has a 2.4 GHz-compliant spectrum analyzer, the peripheral facilities shown below are also
A required.
Also, the antenna terminal on BT unit must be directly connected to the cable.
A white coaxial cable connected to the antenna connector on BT unit is removed by taking out the upper case and
CD mechanics of the product.
This task would be safer if a special connector-drawing jig is available.
Next, the U.FL connector from spectrum analyzer is connected. The styling of cable must be taken good care so as
not to add further burden on BT antenna connector and to break it.
2. Outline of Functions
The following confirmation is to be conducted by test mode in order to simply check BT actions using 2.4 GHz-compliant
spectrum analyzer.
B * Confirmation of output level of Bluetooth unit
3. Configuration Diagram
2.4 GHz-compliant spectrum analyzer
DEH-P9800BT/XN/EW5
A
Remove CD mechanics and
connect to ANT connector
inside Bluetooth unit C
D
B
DEH-P9800BT/XN/EW5
76
1 2 3 4
5 6 7 8
P I O N E E R
←
L O O P B A C K Set to "LOCAL TX NM" by pressing the left/right key.
[Setting screen]
↓ Press the left/right key.
- W I R E L E S S T E S T -
TEST S E T T I N G . . .
L O C A L T X N M
[Local TX NM setting]
↓ Press the Center key.
- W I R E L E S S T E S T -
TEST S E T T I N G . . .
L O C A L T X N M
←
T X F R E Q . : 0 2 - 2 4 0 2 Select the frequency by pressing the up/down key.
02-2402 (Initial value) 41-2441 80-2480 95-2495
Measurement shall be taken at 02, 41 and 80.
[Local TX NM detail setting]
↓ Center key
- W I R E L E S S T E S T - D
TEST E X E C U T E . . .
←
Return to the Local TX NM setting screen by pressing the BAND
L O C A L T X N M key.
T S : - - H M : - - P T : - -
T X : 0 2 R X : - - T G : - -
DEH-P9800BT/XN/EW5
5 6 7 8
77
1 2 3 4
7. GENERAL INFORMATION
7.1 DIAGNOSIS
7.1.1 DISASSEMBLY
A
- Removing the Case (not shown)
C 1 1
Fig.1
3 1
Cord Assy
Fig.2
DEH-P9800BT/XN/EW5
78
1 2 3 4
5 6 7 8
When unplugging the cord assy, make sure to use jig GGF1539.
If the antenna cable is directly unplugged without using jig GGF1539, you might damage your fingertip or fingernail.
GGF1539
1
Cord Assy
Fig.3
2 Connector
Grille Assy
Fig.4
DEH-P9800BT/XN/EW5
5 6 7 8
79
1 2 3 4
A
1 Remove the three screws.
3
2 Straighten the tabs at three locations 1
indicated.
B 2
2 2
DEH-P9800BT/XN/EW5
80
1 2 3 4
5 6 7 8
B
B
A
Damper
Damper D
A
Carriage Mechanism Lower Frame
DEH-P9800BT/XN/EW5
5 6 7 8
81
1 2 3 4
Screw
B
CD Core Unit
Solder
Planet Gear
Pickup Rack
Chassis
Pickup
DEH-P9800BT/XN/EW5
82
1 2 3 4
ANTENNA JACK
5
5
MICROPHONE INPUT
6
6
8 9 10 11
7.1.2 CONNECTOR FUNCTION DESCRIPTION
2 4 6 8 10 12 14 16
1 3 5 7 9 11 5 6 7
2 4 6 8 10 12 1 2 3 4
1 3 5 7 9 11 13 15
DEH-P9800BT/XN/EW5
7
7
PRE OUTPUT POWER SUPPLY, SPEAKER AUX INPUT IP-BUS WIRED REMOTE
CONTROL
1. FL OUTPUT 1. BACKUP 9. RL- 1. BUS+
2. GND 2. GND 10. FL- 2. GND
3. FR OUTPUT 3. ILM 11. RL+ 3. GND
4. GND 4. B.REM 12. FL+ 4. NC
5. RL OUTPUT 5. ACC 13. RR- 5. BUS-
6. GND 6. NC 14. FR- 6. GND
7. RR OUTPUT 7. NC 15. RR+ 7. BUS L+ INPUT
8. GND 8. TEL MUTE 16. FR+ 8. ASENB
9. SWL OUTPUT 9. BUS R+ INPUT
10. GND 10. BUS R- INPUT
11. SWR OUTPUT 11. BUS L- INPUT
12. GND
8
8
83
E
A
D
C
F
B
1 2 3 4
7.2 IC
NJM2886DL3-33 TC7WH32FU AK7732VT PAL007B TC4066BFT
PD8161A PD6544A PM9009A NJM4151M TC74VHC02FTS1
A UPD63763CGJ GP1UX51RK PCM1606EG PM8003A TC7PAU04FU
PE5552A S1D13702F00A100 TC74VHCT08AFTS1 PEG259A AN6123MS
PEG182A HA12241FP TC74VHC08FTS1 S99-50084 AK2301A
NJM2886DL3-33
Thermal
Protection
B
Bandgap
Reference
C - +
1 2 3 4 5
PD8161A
BYTE# 1 48 Vss
D A16 2 47 Vss
A15 3 46 D15/A-1
A14 4 45 D7
A13 5 44 D14
A12 6 43 D6
A11 7 42 D13
8
A10 D15 / A-1 : Data output / Address input 41 D5
A9 9 A0 to A22 : Address inputs 40 D12
A8 10 D0 to D14 : Data outputs 39 D4
A19 11 CE# : Chip enable input 38 Vcc
A21 12 OE# : Output enable input 37 Vcc
A20 13 BYTE# : Word / Byte select input 36 A22
E A18 14 Vcc : Power supply voltage 35 D11
15 Vss : Ground 34
A17 D3
A7 16 33 D10
A6 17 32 D2
A5 18 31 D9
A4 19 30 D1
A3 20 29 D8
A2 21 28 D0
A1 22 27 OE#
A0 23 26 Vss
CE# 24 25 Vss
F
DEH-P9800BT/XN/EW5
84
1 2 3 4
5 6 7 8
DEH-P9800BT/XN/EW5
5 6 7 8
85
1 2 3 4
UPD63763CGJ
109
144
1 108
36 73
F
37
72
DEH-P9800BT/XN/EW5
86
1 2 3 4
5 6 7 8
DEH-P9800BT/XN/EW5
5 6 7 8
87
1 2 3 4
PE5552A
Format meaning
100
76
C C MOS
1 75
25 51
26
50
DEH-P9800BT/XN/EW5
88
1 2 3 4
5 6 7 8
DEH-P9800BT/XN/EW5
5 6 7 8
89
1 2 3 4
25 51
B 26 50
PD6544A
A15 1 48 A16
A14 2 47 BYTE
TC7WH32FU A13 3 46 VSS
A12 4 45 DQ15/A-1
A11 5 44 DQ7
A10 6 A-1 : Address input 43 DQ14
A9 7
A0-A19 : Address input
42 DQ6
C 1A 1 8 VCC A8 8 41 DQ13
A19 9 DQ0-DQ15 : Data input/output 40 DQ5
N.C. 10 CE : Chip enable input 39 DQ12
WE 11
OE : Output enable input 38 DQ4
7 1Y RESET 12 37 VCC
1B 2 WE : Write enable input
N.C. 13 36 DQ11
N.C. 14 RESET : Reset input 35 DQ3
RY/BY 15 RY/BY : Ready / Busy input 34 DQ10
A18 16
BYTE : 8 bit / 16 bit mode select input 33 DQ2
6 2B A17 17 32 DQ9
2Y 3 Vss : Ground
A7 18 31 DQ1
A6 19 Vcc : Power supply 30 DQ8
A5 20 29 DQ0
GND 4 5 2A A4 21 28 CE
D A3 22 27 VSS
A2 23 26 CE
A1 24 25 A0
GP1UX51RK
- Block Diagram - Pin Layout
RL
E
1 2 3
2 3 1 vout GND VCC
GND VCC vout
DEH-P9800BT/XN/EW5
90
1 2 3 4
5 6 7 8
S1D13702F00A100
- Pin Layout
MPUSEL
XRESET
SWAP
SEDO
HVDD
XBHE
SECK
SECS
LVDD
XWR
SEDI
XINT
A
XCG
XRD
XCD
XCS
VSS
CLK
XA0
RS
60 41
40
HVDD LVDD
61
XWAIT GPSO
D[0] GPRO[7]
D[1] GPRO[6]
D[2] GPRO[5]
D[3] GPRO[4]
D[4] GPRO[3]
D[5] GPRO[2]
D[6] GPRO[1] B
D[7] GPRO[0]
VSS VSS
D[8] DIS2B
D[9] DIS1B
D[10] GCLKBB
D[11] GCLKGB
D[12] GCLKRB
D[13] LP2B
D[14] LP1B
D[15] DCLK
80
21
LVDD HVDD
1 20
C
GCLKRA
TESTEN
GCLKGA
DIS1A
DIS2A
GCLKBA
HVDD
LVDD
LP1A
LP2A
YD
VSS
PDA[0]
PDA[1]
PDA[2]
PDA[3]
PDA[4]
PDA[5]
PDA[6]
PDA[7]
- Block Diagram
3.3 V
1.8 V
HVDD
LVDD
RS PDA[7:0]
Memory Bit D
XBHE Processing Layer1
Mediation
XA0 Superposition
XCS Control
XRD Layer2
XWR
XWAIT Parallel 72 K byte DCLK
XINT Frame Memory
YD1
D[15:0] YD2
LP1A
LP2A
512 byte DIS1A
Color Palette DIS2A
SEDI GCLKRA
SECS OLED GCLKGA E
Serial
SECK I/F GCLKBA
I/F
SEDO LP1B
LP2B
REG DIS1B
MPUSEL
DIS2B
SWAP GCLKRB
XRESET
GCLKGB
TESTEN
GCLKBB
XCG
XCD OSC
CLK GPRO[7:0]
General GPSO
Purpose GPCK
F
VSS
DEH-P9800BT/XN/EW5
5 6 7 8
91
1 2 3 4
BIAS
+ DRIVER
OUTPUT
- (current)
+
RECEIVER COM
OUTPUT -
1 2 3 4
S1 R out S2 GND
AK7732VT
- Pin Layout
VREFH
TESTI1
TESTI2
CKM[0]
CKM[1]
VREFL
VCOM
AINR+
AINL+
AVDD
AVDD
AINR-
AVSS
AVSS
AINL-
LFLT
64
63
62
61
60
59
58
57
56
55
54
53
52
51
50
49
EECS 1
48 I2CSEL
D EESO 2
47 EESEL
EECK 3 BVSS
46
EESI 4 45 DVDD
BVSS 5 44 DVSS
DVSS 6 43 XTI
DVDD 7 42 XTO
RQ/CAD1 8 41 DVSS
64pin LQFP
RDY 9 40 DVDD
SO 10 39 LRCLK_O
SI/CAD0 11 38 BITCLK_O
DVSS 12 37 SDOUT1
E DVDD 13 36 SDOUT2
35 SDOUT3
SCLK/SCL 14
34 SDOUT4
SDA 15
33 SDOUT5
CLKO2 16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
STO
SDIN1
SDIN2/JX0
SDIN3/JX2
SDIN4/JX1
SDIN5A/JX0
DVDD
DVSS
BITCLK_I
LRCLK_I
INIT_RESET
CK_RESET
S_RESET
CKM[3]
CKM[2]
CLKO1
DEH-P9800BT/XN/EW5
92
1 2 3 4
5 6 7 8
- Block Diagram
AINL+ AINL- AINR+ AINR- VREFL VCOM VREFH
A
2 AVDD
2 AVSS
2 BVSS
ADC REF
5 DVDD
SDATA_AD
5 DVSS
SWAD_N
SWIRPT
SWQ5
SDIN5A/JX0 SDIN5 SDOUT5
SWG1 OUT5E_N SDOUT5
SWQ4
SDIN4/JX1 SDIN4 SDOUT4
SWG0 OUT4E_N SDOUT4 B
SWQ3
SDIN3/JX2 SDIN3 SDOUT3
OUT3E_N SDOUT3
SWQ2
SDIN2/JX0 SDIN2 SDOUT2T
OUT2E_N SDOUT2
SWQ1
SDIN1 SDIN1 SDOUT1T
OUT1E_N SDOUT1
TEST
GPO1
GPO0
RQ/CAD1 RQ/CAD1
JX0_E JX0 SCLK SCLK/SCL
SI/CAD0 SI/CAD0
JX1_E JX1 SO C
SO
RDY
JX2_E JX2 RDY
SDA
SDA
WDT
DSP STO
CRC
CRC_E
EESEL EESEL EESI EESI
EECK EECK
TESTI1
EECS EECS
TESTI2 EESO
INIT_RESET EEPIL EESO
CONTROLLER EEST
S_RESET D
CK_RESET XTI
4 XTO
CKM[3:0] (Master="L",Slave="H") PLL&DIVIDER
I2CSEL CLKO2E_N CLKO2
SMODE
CLKO1E_N CLKO1
DEH-P9800BT/XN/EW5
5 6 7 8
93
1 2 3 4
PM9009A
D.GND
- Pin Layout
Vo6b
Vo5b
Vo4b
Vo3b
Vo2b
Vo1b
Vo7a
Vo6a
Vo5a
Vo4a
Vo3a
Vo2a
Vo1a
A
42 41 40 39 38 3736 35 34 3332 31 30 29
SDA 43 28 Vi7
SCK 44 27 S.GND.7
CS 45 26 Vi6
FCKSEL 46 25 Vi5
Vee 47 24 S.GND.6
NEGOUT 48 23 Vi4
C- 49 22 Vi3
P.GND 50 21 S.GND.5
C+ 51 20 Vi2
B
Vcc 52 19 Vi1
ADJ 53 18 S.GND.4
S.GND.MU 54 17 So1R
Exi+ 55 16 So1L
Exi- 56 15 So2R
1 2 3 4 5 6 7 8 9 1011 12 13 14
Si1L+
Si1L-
Si1R-
Si1R+
S.GND.1
Si2L
Si2R
S.GND.2
Si3L
Si3R
Si4L
Si4R
S.GND.
SO2L
C - Block Diagram
FCKSEL
NEGOUT
Vcc
ADJ
C+
Vee
C-
Change Pump
Circuit
CS Fck (Fcp)
Control VCO Divider Regulater Regulater
SCK
Logic Fck
+Vcc
+7 V
-Vcc
-7 V
SDA
(Volume Circuit)
D
Power Supply Circuit
Volume Circuit
(+23 to -79 dB,-∞ dB)
Vo1a
Volume(1 to 7 ch)
(0 dB/+1.8 dB)
Buffer Amp A
Selector Vo2a
Gain Adjuster 1
Circuit Vo3a
E Si4L
Source Selector(1 ch / 2 ch)
Vo4a
Si3L
Vo5a
Si2L
Vo6a
GND Isolator
Si1L+
Vo7a
Si1L-
Vo1b
Gain Adjuster 2
(0 dB/-4.2 dB)
Si1R-
Buffer Amp B
Vo2b
Si1R+ Vo3b
Si2R Vo4b
Si3R Vo5b
Si4R
So2R
So1R
So2L
So1L
Vo6b
Vi1
Vi2
Vi3
Vi4
Vi5
Vi6
Vi7
DEH-P9800BT/XN/EW5
94
1 2 3 4
5 6 7 8
PCM1606EG
- Pin Layout
DATA1 1 20 SCKI
A
DATA2 2 19 BCK
DATA3 3 18 LRCK
FMT1 4 17 DEMP1
FMT0 5 16 DEMP0
ZEROA 6 15 VCC
AGND 7 14 VCOM
VOUT5 8 13 VOUT4
VOUT6
B
9 12 VOUT3
VOUT1 10 11 VOUT2
- Block Diagram
System Clock
SCKI Manager Zero Detect Power Supply
D
TC74VHCT08AFTS1,
TC74VHC08FTS1
1A 1 14 VCC
1B 2 13 4B
E
1Y 3 12 4A
2A 4 11 4Y
2B 5 10 3B
2Y 6 9 3A
F
GND 7 8 3Y
DEH-P9800BT/XN/EW5
5 6 7 8
95
F
E
B
A
D
C
96
4
3
2
1
PAL007B
1
1
sw_vcc
NJM4151M
Protector;
Over voltage
- Pin Layout
TAB Reference
amp_vcc
Stand-by
2
P-GND2 Circuit
3
+-
5
6
7
8
OUT2-
Offset Protector;
4
STBY Detection Thermal
5
-+
OUT2+
6
VCC
7
+-
IO
Th
OUT1-
V1
7
6
2
1
8
V+
Offset
8
P-GND1 Detection
2
2
9
-+
OUT1+
10
SVR
11
IN1
IN2
- Block Diagram
Protector;
12 13
S-GND Short circuit
amp_vcc
IN4 14
M Z
15
IN3
DEH-P9800BT/XN/EW5
N
AC-GND
V
F
3
+-
16 17
OUT3+
3
3
Offset
18
P-GND3 Detection
R
-+
19
OUT3-
S
VCC
5
+-
20 21
OUT4+
RO
P
Offset
22
MUTE Detection
X
-+
23
OUT4-
T
P-GND4
U
24 25
SWITCH
4
Protector;
4
4
sw_vcc
W V
V+
Mute circuit
5 6 7 8
PM8003A
- Pin Layout
BUSY2/ERR
A
OPTANA
DGND
DVDD
WR
NC
NC
NC
NC
NC
CS
44
43
42
41
40
39
38
37
36
35
34
NC 1 33 NC
DW 2 32 SERIAL
BUSY1 3 31 DGND
NCR2/DL 4 30 AVDD
NCR1/NDR 5 29 AOUT
RD 6 28 DAO B
TESTO1 7 27 AGND
TESTO2 8 26 D7/DI
RESET 9 25 NC
TEST 10 24 D6/SCK
NC 11 23 D5/DO
12
13
14
15
16
17
18
19
20
21
22
NC
DVDD
XT
XT
D0
DGND
D1
D2
D3
D4
NC
C
- Block Diagram
16 2 bit ADPCM2
16 bit 1 Mbit
NCR1/NDR Multiplexer ROM /4 bit ADPCM2
NCR2/DL Synthesizer
BUSY1
BUSY2/ERR
SERIAL 8 bit PCM
Phrase Control 16 bit PCM D
D7/DI
Table Synthesizer&2 ch Mix
D6/SCK 16 bit
D5/DO Address Controller
CPU
D4
interface
D3
D2 Loop Volume Digital Filter
D1
D0
WR
Commnad
CS Controller
DW 14 bit DAC E
RD
OPTANA
XT
OSC Timing Controller AVDD
XT
AGND
DEH-P9800BT/XN/EW5
5 6 7 8
97
1 2 3 4
- Pin Functions(PEG259A)
Pin No. Pin Name I/O Function and Operation
1 DPDT O GRILLE : Data output
A 2 SWVDD O GRILLE : Chip enable output
3 OELPW OEL power supply output
4 NC Not used
5 MEMDO O External memory : Data output
6 MEMDI I External memory : Data input
7 MEMCK O External memory : Clock output
8 NC Not used
9 FLPOPN O Flap open operation output
10 FLPCLS O Flap close operation output
11 FOPNSW I Flap open sense input
12 FCLSSW I Flap close sense input
B
13 FLPPW O Flap motor operation output
14 NC Not used
15,16 BYTE1,2 I Connect to GND
17 NC Not used
18 ROMDATA I/O ROM correction : Data input/output
19 reset I Reset input
20 Xout O Clock output
21 Vss GND
22 Xin I Clock input
23 Vcc1 Power supply terminal
24 NMI I Not used
25 RCK I RDS : Clock input
C 26 LDET I RDS : PLL lock detect input
27 ROMCK O ROM correction : Clock output
28 NC Not used
29 ROMCS O ROM correction : Chip select output
30 RDS 57K I RDS : 57 kHz pulse count input
31 PEE O PEE sound output
32 NC Not used
33 RDT I RDS : Data input
34 TUNPCE1 O TUNER : Chip enable output
35 TUNPCE2 O TUNER : Chip enable output
36 RX I IPBUS : Input
37 TX O IPBUS : Output
D 38 BSO O P-BUS output
39 VCC1 Power supply terminal
40 BSI I P-BUS input
41 VSS GND
42 BSCK O P-BUS clock output
43 NC Not used
44 BTTX O BT driver : Data output
45 BTRX I BT driver : Data input
46 RTS0 O BT driver : RTS output
47 BTCTS I BT driver : CTS input
48 RDSLK I RDS : Lock signal input
49 TUNPDI I TUNER : PLL data input
E
50 TUNPDO O TUNER : PLL data output
51 TUNPCK O TUNER : PLL clock output
52 AUIWR O AUI : Write signal output
53 AUICS O AUI : Chip select output
54 AUISDO O AUI : Data output
55 AUISCK O AUI : Serial clock output
56 AUIRST O AUI : Reset output
57 VSS GND
58 MUTE O System mute output
DEH-P9800BT/XN/EW5
98
1 2 3 4
5 6 7 8
DEH-P9800BT/XN/EW5
5 6 7 8
99
1 2 3 4
PEG259A S99-50084
36 1
144
CS# 1 8 VCC
37
C SCK : Serial clock input
SI : Serial data input
SO 2 SO : Serial data output 7 HOLD#
CS# : Chip select input
W# : Write protect input
109 W# 3 HOLD#: Hold input 6 SCK
72
Vcc : Power supply
GND : Ground
73 108 4 5
GND SI
D
TC4066BFT
1I/O 1 14 VCC
1O/I 2 13 1C
2O/I 3 12 4C
2I/O 4 11 4I/O
E
2C 5 10 4O/I
3C 6 9 3O/I
GND 7 8 3I/O
DEH-P9800BT/XN/EW5
100
1 2 3 4
5 6 7 8
TC74VHC02FTS1 TC7PAU04FU
A
1A 1Y
1 1Y 14 VCC
13 4Y
2 1A
GND Vcc
12 4B
3 1B
B
4 2Y 11 4A
2A 2Y
5 2A 10 3Y
6 2B 9 3B
C
7 GND 8 3A
D
AN6123MS
DET gm E
2 1
DET VCC
DEH-P9800BT/XN/EW5
5 6 7 8
101
1 2 3 4
AK2301A
- Pin Layout
A
24 23 22 21 20 19 18 17 16 15 14 13
1 2 3 4 5 6 7 8 9 10 11 12
- Block Diagram
C
GST
VFTN - A/D DX
VFTP + AAF
DR
AMPT
FS
BCLK
PCM I/F
VR SMF D/A
VFR
D AMPR CODEC Core
GSR -
+
Internal
PLL
Main Clock
TAGND PLLC
MUTEN
VREF BGREF
RSTN
VDD
AMP1 AMP2 TEST1
E VSS
- - TEST2
+ + TEST3
DEH-P9800BT/XN/EW5
102
1 2 3 4
5 6 7 8
CE2
ROM_VDD
SL
DI
CK
CE1
LDET
DO
RDS_CK
RDS_DATA
RDS_LOCK
RDS_HSLK
NC
A
IC 3 EEPROM IC 5
←
5.0 V 5 V 3.3 V
OSC LPF
AM ANT FMRF
1 ATT
Rch
24
IC 2
IC 1 2.5 V
FM ANT
3 3.3 V
ATT Lch
23
FMRF MIXER, IF AMP DET, FM MPX,
RDS DECODER
ANT adj
RF adj B
T51 CF52
AUDIOGND
IC 4
OSCGND
VDD_3.3
←
RFGND
VCC
NC
2 12 15 22 16 4 17
DEH-P9800BT/XN/EW5
5 6 7 8
103
1 2 3 4
A
Power ON
VCC1 = 5 V
Pin 23
bsens
Pin 104
B
bsens = L
asens
Pin 103
asens = L
DSENS
Pin 137
C
1.5 V < DSENS < 4.5 V
ASENBO←H
Pin 65
Starts
communication
with Grille
microcomputer. 300 ms
SWVDD←H
D Pin 2 300 ms
In case of the above signal, the communication
Source keys with Grille microcomputer may fail.
operative If the time interval is not 300 msec, the oscillator
may be defective.
Source ON
SYSPW←H
Pin 99
DEH-P9800BT/XN/EW5
104
1 2 3 4
5 6 7 8
8. OPERATIONS
DEH-P9800BT/XN/EW5
5 6 7 8
105
1 2 3 4
DEH-P9800BT/XN/EW5
106
1 2 3 4
5 6 7 8
DEH-P9800BT/XN/EW5
5 6 7 8
107
1 2 3 4
DEH-P9800BT/XN/EW5
108
1 2 3 4
5 6 7 8
DEH-P9800BT/XN/EW5
5 6 7 8
109
1 2 3 4
DEH-P9800BT/XN/EW5
110
1 2 3 4
5 6 7 8
DEH-P9800BT/XN/EW5
5 6 7 8
111
1 2 3 4
- Jigs List
Name Jig No. Remarks
Test Disc TCD-782 Checking the grating
A L.P.F. Checking the grating (Two pieces)
GGF1539 Removingg the cord assy(BT
y( antenna cable))
- Grease List
Name Jig No. Remarks
Grease GEM1024 CD Mechanism Module, Drive Unit
Grease GEM1045 CD Mechanism Module
Grease GEM1069 Drive Unit
B
Before shipping out the product, be sure to clean the
following portions by using the prescribed cleaning
tools:
Portions to be cleaned Cleaning
g tools
CD pickup lenses Cleaning liquid : GEM1004
Cleaning
g paper
p p : GED-008
DEH-P9800BT/XN/EW5
112
1 2 3 4