Professional Documents
Culture Documents
TM
The standards-based, high-performance DeltaV Control Network is easy to install and maintain.
Flexible Benefits
Redundant Plug-and-play components. You can expand the
network easily: just plug in another workstation or
controller and it is recognized by the system.
Introduction
Standards compliance. Network components are
Your control network is the backbone of your compliant with standards such as IEEE, CE and
system. The DeltaV Control Network is a standard CSA.
Ethernet network dedicated to the DeltaV system.
You connect the DeltaV workstations and the Installation under power. You can install and
controllers using the Control Network. remove nodes under power. Hubs and switches
make a convenient attachment point for new nodes:
The Control Network is a dual-speed 10/100BaseT
no breaking of existing cables or failover issues in a
network. CAT 5 screened (ScTP) twisted-pair cable
redundant system.
connects each node to the hub or switch.
Network diagnostics. On the managed switches
The DeltaV system supports a specific set of
you can use software diagnostics to verify proper
network hubs and switches for the DeltaV Control
Product Data Sheet
DeltaV Control Network Hardware
April 2007—Page 2
TM
communication-line health. The LEDs on each switch products are available in both managed and
individual hub/switch provide health status unmanaged versions. Both switch types use a store-
information. and-forward method of packet forwarding, which
ensures that corrupt packets are dropped from the
Off-the-shelf products. DeltaV systems use the network at the earliest possible point of entry on the
highest-quality third-party products to ensure network. The switch is a higher-performance device
reliability. than a hub because each port on a switch is a
separate collision domain, which means that multiple
Scalable in small increments. The DeltaV system port-to-port communications can take place
provides a package with very low initial cost. You simultaneously without interfering with each other,
are able to expand the system readily and and there are no collisions between end nodes. On
economically by adding hardware incrementally to a hub, all devices are in a single-collision domain,
your system. Further, the Control Software comes which means that collisions take place between end
with different sizing and functionality options tailored nodes. Therefore, the more devices there are the
to your needs. more collisions there are—resulting in a slower
overall performance of the system.
Fast communication. The hub and switch products
that have been qualified for use with the DeltaV Redundant. The Control Network is a fully
system are active devices that operate transparently redundant communication network. Nodes may also
on the network. The switch products differ from hub be connected using a simplex network but this is not
products in that the hubs are unmanaged, and the a recommended practice.
TM
TM
Ordering Information
10/100 Unmanaged Switches
When ordering, please make sure to use the model number for destination country. The appropriate electrical
connectors will be selected for compatibility with local power requirements.
Note
The switches in this section are low port density, unmanaged switches intended for use in smaller DeltaV
systems containing up to 12-15 network devices. They are offered to replace the network hubs that are no longer
available. For larger systems, please use the managed switches in the next section. It is possible to use the Allied
Telesyn switches in the same network as the Cisco switches and any existing 3COM devices. (For detailed
technical information please see www.alliedtelesyn.com). This unit comes with a rack mount kit and can be
installed on 19” rack rails.
The Fiber-optic to Copper Ethernet switches were developed for use in Class 1 Div. 2 and Class 1 Zone 2 remote
I/O installations to provide an energy-limited fiber-optic link to IS-classed areas. They can also be used as
unmanaged switches on the DeltaV communications network for connections between controllers and DeltaV
workstations.
TM
TM
TM
Note
The Catalyst® 2950- 24 is a 1-rack unit (RU) stackable** switch providing 24 10/100 ports. It comes with a rack
mount kit.
The Catalyst® 2950C- 24 is a 1-rack unit (RU) stackable** switch providing 24 10/100 ports and two fixed
100BASE-FX uplink ports. It comes with a rack mount kit.
TM
Note
The Catalyst® 2940 switch is a small, standalone, managed switch with eight Fast Ethernet ports and a single
integrated Fast Ethernet FX Fiber uplink and 1000base-X slot. The switches are designed to be used outside the
wiring closet in the end-user workspace with easy wall or under-the-desk mounting. (The unit is not designed for
19” rack mounting—it requires a shelf or other mounting arrangement if rack mounting is required.) An optional
cable guard is available from Cisco to secure the Ethernet cables and switch.
Product Data Sheet
DeltaV Control Network Hardware
April 2007—Page 9
TM
The DeltaV system supports gigabit connections only between switches. Connections between
workstations and controllers are still 100MB.
TM
VE6023
Cisco GLC-SX-MM
VE6024
Cisco GLC-LH-SM
VE6025
Cisco GLC-T
Product Data Sheet
DeltaV Control Network Hardware
April 2007—Page 11
TM
Hubs
This hub is offered for use in very small DeltaV systems of 3-5 nodes, usually a demo or training system. If it is
used in a system installed in an operating facility, special installation is required to properly connect the CAT5
cable shield to a ground bar because this device does not ground cable shields via the power cord ground. These
hubs can be mixed with Allied Telesyn, Cisco or existing 3COM network devices.
VE6001P1
Cabling
TM
Note
The Fiber-optic crossover cable is used to connect the VE6014 switch to the fiber port on the VE6013 or VE6015.
The VE6014 has no Cu ports and must connect through a device with fiber and Cu ports.
* Versions are correct as of the latest revision of this document but are subject to change without notice. If
switches are supplied by others, they must have their software versions flashed to the supported version and they
must be configured specifically for use with the DeltaV system per the instructions in our documentation. Please
confirm latest supported software versions with your DeltaV sales office before providing equipment not
purchased from Emerson Process Management.
** These units are “stacked” by using standard CAT5 or Fiber MTRJ cables on the front panel connections. A
single 100MB connection provides sufficient bandwidth to interconnect these switches in a DeltaV system. DeltaV
supports Cisco EtherChannel connections if more bandwidth is desired. Note that “stacking” these devices
reduces the available front panel connections by one port for each “stacked” connection.
To locate a sales office near you, visit our website at: www.EasyDeltaV.com/reach
For large power, water, and wastewater applications contact Power and Water Solutions at:
www.emersonprocess-powerwater.com
The contents of this publication are presented for informational purposes only, and while every effort has been made to ensure their accuracy, they are
not to be construed as warrantees or guarantees, express or implied, regarding the products or services described herein or their use or applicability.
All sales are governed by our terms and conditions, which are available on request. We reserve the right to modify or improve the design or
specification of such products at any time without notice.