Professional Documents
Culture Documents
carbon steel
alloy of carbon and iron containing up to carbon and up to manganese and residual quantities of other
elements, except those intentionally added in specific quantities for deoxidation (usually silicon and/or
aluminum)
Carbon steels used in the petroleum industry usually contain less than 0,8% carbon.
99.9
99.5
99.2
99.4
vessel is to contain fluids of such a nature that a very small amount mixed or unmixed with air is
dangerous to life when inhaled,
Vessel fill with the high-pressure fluid if it breaks it will affect the human life.
5)Tack welds used to secure alignment shall either be removed completely when they have served their
purpose, before completing weld.
True /False
6)If the vessel is design according to ASME DIV 1 may be stamp ? U? Designated stamp may not
required to apply
True /False
7) Welder qualification expiration baseed on
If the welder did not perform weld process more than 6 month
If the welder is sick and not done welding more than 6 month
When there is a specific reason to question the welder's ability to make welds that meet the
specification
All of above
.welding with equipment that has controls that can be adjusted by the welding operator, or
adjusted direction, in response to changes in the welding conditions.
welding wherein the entire welding operation is performed and controlled by hand.
11)Machin welding & automatic welding is essential variable for welding operator
Ture/False
12) Inspection code covers the in-service inspection, repair, alteration, and rerating activities for
pressure vessels
API 510
API 653
API 620
API 650
13) a pneumatic test may be used in lieu of the standard hydrostatic test
14) Pressure retaining component shall not be closer than from adjacent edge of any other weld
25
50
100
75
The cut end of one of the end plate sections, approximately 1 in. (25 mm) long, in Figure QW-
462.4(b) or the cut end of one of the pipe quarter sections in Figure QW-462.4(c), as applicable,
shall be smoothed and etched with a suitable etchant (see QW-470) to give a clear definition of
the weld metal and heat-affected zone. In order to pass the test
The cut end of one of the end plate sections, approximately 2 in. (50 mm) long, in Figure QW-
462.4(b) or the cut end of one of the pipe quarter sections in Figure QW-462.4(c), as applicable,
shall be smoothed and etched with a suitable etchant (see QW-470) to give a clear definition of
the weld metal and heat-affected zone. In order to pass the test
The cut end of one of the end plate sections, approximately 4 in. (100 mm) long, in Figure QW-
462.4(b) or the cut end of one of the pipe quarter sections in Figure QW-462.4(c), as applicable,
shall be smoothed and etched with a suitable etchant (see QW-470) to give a clear definition of
the weld metal and heat-affected zone. In order to pass the test
The cut end of one of the end plate sections, approximately 3 in. (75 mm) long, in Figure QW-
462.4(b) or the cut end of one of the pipe quarter sections in Figure QW-462.4(c), as applicable,
shall be smoothed and etched with a suitable etchant (see QW-470) to give a clear definition of
the weld metal and heat-affected zone. In order to pass the test
NACE TM0284
NACE TM0248
NACE TM0208
200
300
400
350
18)Vessel manufacturer shall prepare as built drawings, which indicate thickness of the vessel shell
section, heads, and nozzles. An adequate number of readings shall be taken to represent the actual
thickness of the components by using which method
UT
RT
ET
MT
The term “Category” as used herein defines the location of a joint in a vessel, but not the
type of joint. Category WA,WB,WCW,D
The term “Category” as used herein defines the location of a joint in a vessel, but not the
type of joint. Type joint 1,2,3,4
A,
B
C
D
21) If vessel made by two different P no material then heating temp base on
True /False
Full
Spot
None
None of the above
100%
85%
50%