Professional Documents
Culture Documents
User manual
Getting started with the STEVAL-PLC001V1 industrial PLC evaluation board with
HMI interface
Introduction
The STEVAL-PLC001V1 evaluation board targets compact programmable logic controller (PLC) applications in the factory
automation domain. It features a powerful human machine interface (HMI) thanks to the 3.5” TFT touchscreen mounted on the
PCB, which eases interaction with the tool.
The board implements a galvanically isolated PLC control unit with robust digital input, digital output modules, expansion
connectivity options, and interfaces.
The control unit consists of a powerful 144-pin STM32F746ZGT7 MCU, which handles the industrial IOs on one side and
the TouchGFX display technology on the other side, implementing the ladder logic programming code and several additional
options.
Highly robust and reliable industrial digital input and output modules are placed symmetrically on the PCB, making the system
a 12+12 PLC, that is, a PLC GUI optimized for STM32 microcontrollers, which manages 12 industrial inputs and 12 industrial
outputs.
The 12 industrial inputs have been implemented through the combination of an eight-channel CLT01-38SQ7 and two dual
channel CLT03-2Q3 ICs.
The CLT01-38SQ7 features 6.25 MHz SPI with daisy chain capability to connect, in this case, the eight-channel output
ISO8200AQ and reverse polarity, whereas the CLT03-2Q3 features two high- and low-side compatible independent channels,
which can be powered from the external sensors they interface with, and the capability of running in the 60 V range for fail-safe
applications.
The 12 industrial output array consists of an eight-channel ISO8200AQ IC and a four-channel IPS4260L low-side intelligent
power switch.
The ISO8200AQ offers a daisy-chain SPI interface and embedded galvanic insulation, separating logic and power side of 4 kV
and making the solution cost-effective (no opto-coupler is needed).
The STEVAL-PLC001V1 also features connectivity options typical of commercial PLCs through the morpho connectors mounted
on the PCB bottom, ensuring compatibility with STM32 Nucleo expansion boards.
The embedded ICs for industrial IO management allow great flexibility in terms of technical features, protections and embedded
diagnostics, when interfacing industrial range inputs (that is, sensors and valves) and outputs (that is, lamps, alarms, and
actuators) with the logic side.
The STSW-PLC001 companion software package, freely available on www.st.com, allows experimenting with these advanced
features and their combination.
Thanks to this software and the smart user interface offered by the TouchGFX, you can learn how the ICs work and exploit
ready-to-use examples as well as ladder logic demonstrations and projects.
1 Getting started
Danger:
People with active implanted medical devices shall not use this evaluation kit, as safety related to
radiated emissions is not guaranteed.
1.2 Features
• STM32F746ZGT7 high-performance MCU embedding ARM® 32-bit Cortex®-M7 CPU with FPU, Chrom-ART
accelerator, and DSP instructions
• CLT01-38SQ7 octal high-speed digital input current limiter with SPI interface
• CLT03-2Q3 dual-channel self-powered digital input current limiter
• ISO8200AQ galvanic isolated octal high-side smart power solid-state relay with SPI interface
• IPS4260L quad low-side intelligent power switch
• Main supply voltage: 18 - 32 V (24 V nominal)
• STSW-PLC001 firmware package
• 3.5" TFT display with multitouch capability interfaced through dedicated parallel, digital RGB ports and I²C
lines
• STLD40DPUR-based display back-light LED driver with controllable intensity
• Morpho connectors for expansion connectivity options
• Screw connectors for safer power supply and industrial IO connections
• USB connector for alternate 5 V source power supply (only for display powering and MCU programming/
debug)
• Isolated USART port connector
• SWD connector for debugging and programming
• Status LEDs for inputs, outputs, and various fault conditions
• Debug LEDs
• Reset button
• Protections against surge, EMI, and input reverse voltage connection
• EMC pad and four-layer routing
• On-board RAM and serial Flash (ROM)
• Provision for RTC, USB (with one or more additional components to be mounted)
• Designed to meet IEC industrial standard requirements
• RoHS
CLT03-2Q3 CLT03-2Q3
CLT03-38SQ7 2-ch self- 2-ch self-
8-channel high-speed powered powered
SPI
SPI
opto
24 VDC
DC-DC LDK220
converter 200mA
Isolated LDO
ISO8200AQ IPS4260L STLD40DPUR
8-channel isolated HS
Non ST and
4-channel LS Backlight LED driver
Protections + Filter passive
Current mode Step up
Various ICs Converter components
12 industrial output Screw connector
24 V 0H 1H 2H 3H GND
24 V 0L 1L 2L 3L GND
Optional 5 V input
(non-isolated, for demo mode only)
-ve/+ve
24 V to field
24 V input supply
Q1: 4 low-side digital outputs
(IPS4260L)
Q1.0 Q1.1 Q1.2 Q1.3
1 2
3
6
45
7 8
9
6
3 4
1
2
5 7
1.5.1 CLT01-38SQ7
The CLT01-38SQ7 is the 8-channel current limiter termination with high-speed SPI interface. The STEVAL-
PLC001V1 features daisy chain connection via SPI for this IC, the ISO8200AQ on the output side and the morpho
connectors. The three peripherals exploit daisy chain connection allowing less wiring on the PCB.
The CLT01-38SQ7 provides an 8-line protected digital input termination with serialized state transfer. It enhances
the I/O module density by cutting the dissipation (78 mW per input) and reducing the count of opto-transistors. Its
6.25 MHz SPI peripheral output serializes the input state transfer to the I/O module controller.
Available in a 7x7 QFN package with 48 leads, the device complies with the following standards: IEC61000-4-2
(±8 kV contact discharge and ±15 kV air discharge), IEC61000-4-4 (±4 kV) and IEC61000-4-5 (input = ±1 kV,
power supply = ±2.5 kV).
1.5.2 CLT03-2Q3
The CLT03-2Q3 is a digital input current limiter which drastically reduces the power dissipation of digital inputs. It
does not require external power supply as the device is activated with the input signal and consumes no power in
off state.
The CLT03-2Q3 features two independent channels and is high-side, low-side and reverse plug-in compatible. It
can drive opto-couplers or 3.3 V LVTTL circuits.
The STEVAL-PLC001V1 hosts two CLT03-2Q3 in a 16-lead QFN package to reach a 12-input array. The device
enables industrial inputs to meet type 1 and 3 characteristic of IEC 61131-2 standard, while the IC complies with
the following standards:
• IEC 61000-4-2 level 1: ±4 kV (air discharge)
• IEC 61000-4-2 level 1: ±2 kV (contact discharge)
1.5.3 ISO8200AQ
The ISO8200AQ is a galvanic isolated 8-channel driver featuring a very low supply current. It embeds two
independent galvanic isolated voltage domains (VCC and VDD for process and control logic stages, respectively).
The IC is designed to drive any kind of load (inductive, resistive or capacitive) with one side connected to ground.
The control logic stage features an 8-bit output status register (where the microcontroller sets the ON/OFF status
of the output channels in the process stage) and an 8-bit fault register (where the OVT faults of each channel are
stored). The two stages communicate through the galvanic isolation channel via an ST proprietary protocol.
Active channel current limitation (OVL) combined with thermal shutdown (OVT), independent for each channel,
protects the device against overload and overtemperature. Additional embedded functions include loss of ground
protection, VCC and VDD UVLOs (with hysteresis), watchdog and VCC PGOOD.
An internal circuit provides an OR-wired not latched common (FAULT) indicator signaling the channel OVT. The
PGOOD diagnostic pin is activated if VCC falls below the power good internal threshold. Both FAULT and PGOOD
pins are open drain, active low, fault indication pins.
The device is UL1577 certified and is designed to meet IEC 61000-4-2, IEC 61000- 4-4, IEC 61000-4-5 and IEC
61000-4-8 standards. The package is TFQFPN32.
1.5.4 IPS4260L
The IPS4260L is a monolithic high speed (FSW up to 250 kHz) device, which can drive four independent
capacitive, resistive, or inductive loads with one side connected to the supply voltage. The channels can be
paralleled to reduce power dissipation.
When connected to VCC rail, four integrated catch diodes clamp the turn-off transients generated by inductive
loads even with huge inductance; combined with proper external TVS connected to VCC or to GND the IC allows
fast decay, too. Each channel is protected against overload or short-circuit: the intervention level can be set
by an external resistor on ILIM pin (see device data sheet for details). Built-in thermal shutdown protects the
chip against overtemperature even in case of short-circuit. If enabled, the integrated cut-off protection features a
non-dissipative protection in case of overload; it limits both the output average current value and, consequently,
the device overheating.
Cut-off delay/restart can be programmed by external resistors on CoD pin; it can be disabled by shorting CoD to
GND. Two common diagnostic open drains pins (OL, for open load and FLT for cut-off and thermal shutdown)
together with the four open drain on each INx pin (cut-off and thermal shutdown) feature an extensive diagnostic
of the chip.
The package is a miniaturized HTTSSOP20 and is designed to meet IEC 61131-2 standard.
1.5.5 STM32F746ZG
The STM32F746ZG microcontroller is the core of our evaluation board and is responsible for the management of
all industrial I/O ICs and for the HMI running on the 3.5 display with the TouchGFX technology.
The STM32F746xx devices are based on the high-performance ARM® Cortex®-M7 32-bit RISC core operating
at up to 216 MHz frequency. The Cortex®-M7 core features a single floating point unit (SFPU) precision which
supports all ARM® single-precision data-processing instructions and data types. It also implements a full set of
DSP instructions and a memory protection unit (MPU) which enhances the application security.
The STM32F746xx devices incorporate high-speed embedded memories with a Flash memory up to 1 Mbyte,
320 Kbytes of SRAM (including 64 Kbytes of Data TCM RAM for critical real-time data), 16 Kbytes of instruction
TCM RAM (for critical real-time routines), 4 Kbytes of backup SRAM available in the lowest power modes, and
an extensive range of enhanced I/Os and peripherals connected to two APB buses, two AHB buses, a 32-bit
multi-AHB bus matrix and a multi-layer AXI interconnect supporting internal and external memories access.
All the MCUs in this family offer three 12-bit ADCs, two DACs, a low-power RTC, thirteen general-purpose
16-bit timers including two PWM timers for motor control and one low-power timer available in stop mode, two
general-purpose 32-bit timers, a true random number generator (RNG). They also feature standard and advanced
communication interfaces. For further details, see the device data sheet.
The LCD-TFT controller interface with dual-layer support takes advantage of the Chrom‑ART Accelerator. This
graphics accelerator creates content twice as fast as the core alone and features 2-D raw data copy, image format
conversion and image blending.
5V_CLT01
isolator 3.3 V
opto opto RAM Logic device
STL42P6LLF6 3.3 V
PMOS for GPIO
24 V Reverse Voltage 24 V
Protection SPI FLASH isolator
STM32F746 3.5” LCD +
DC-DC 5V LDK220M3R 3.3 V MCU Touch Field-side
converter Screen device
24 V
(24V to 5V)
STLD40D is a boost converter (5 V supply to ~18 V) needed for the LCD back-light. The converter is a pulse
frequency modulation (PFM) inductor switch that can work in discontinuous mode (DCM). A minimum OFF time of
the embedded TSW boost switch is fixed internally and allows limiting the switching frequency. The output current
capability is 20 mA with an output voltage of 37 V (maximum rating). The regulation is done by sensing the LED
current through a current resistor (R86). The device can be turned ON/OFF through the logic enable signal pin
(EN). A low frequency PWM signal is used to dim the LCD back-light.
Morpho connectors (J17, J18) gives provision for connectivity with compatible boards such as STEVAL-
IOM001V1 if you want to add IO-Link master capabilities to our PLC.
For further details on MCU interfaces, see Section Appendix A which summarizes the information contained in
the .ioc file provided with the STSW-PLC001 firmware and the schematic.
Note: D22 is triggered by the OL pin of IPS4260L, which indicates open load condition or short to ground condition.
Open load detection feature is activated by placing proper resistors between LOADx and PGND ground plane.
In the STEVAL-PLC001V1 evaluation board, there are resistors placed for open load detection for the Q1.X four
outputs. For Q1.2 and Q1.3, instead, they are activated only if J8 and J9 jumpers are closed. Thus, the Fault
LED (D22) might glow when there is no load connection or partial connection to output terminals.
Numerous test points are provided on the board (see Section 4 Schematic diagrams).
To run the STEVAL-PLC001V1 evaluation board with the STSW-PLC001 preloaded firmware, you have two
possibilities to power the board up:
1. through the micro-USB connector with an appropriated power supply (i.e. 5 V, 1 A): with this option, you
can access limited board functions like programming/debugging through the SWD connector or use the
touchscreen display to show the features of the industrial ICs mounted on the board. This mode is intended
for demonstration only or to use MCU logic circuit only;
2. through the screw connector (24 V) placed in the bottom-left corner: this option offers the complete
experience with the STEVAL-PLC001V1, that is all programming/debugging and display features can be
executed, and the industrial I/O can be handled with the highest possible current ratings allowed by the
ICs (i.e. you can drive several output loads requiring up to 0.7 A of current each through the output screw
connector placed on the bottom side).
STSW-PLC001 provides the framework to use all the STEVAL-PLC001V1 modules including TouchGFX-based
HMI. After powering up, you just have to select one of the user modes through the touchscreen.
The STSW-PLC001 companion software package is available for download at www.st.com. It is designed as a
development tool for industrial PLCs.
To use the STEVAL-PLC001V1 board and the associated firmware, power supply the board (24 V or through a
portable USB power supply) and play with the user interface powered by the TouchGFX technology featuring HMI
capabilities. Freely customizable C-code written examples are also provided to speed up the development time.
HAL component
STM32 HAL Library
For further details on user APIs, touch display engine and demonstration use-cases, refer to the STSW-PLC001
user manual (UM2938, freely available on www.st.com).
VDD
I0.0
I0.1
I0.2
I0.3
I0.4
I0.5
I0.6
I0.7
I1.3L
I1.2L
I1.1L
I1.0L
I1.3H
I1.2H
I1.1H
I1.0H
3V3 VDD
GND_Logic 3V3
VDD SPI2_MISO GND_Logic DI_I1_1
GND_Logic VDD SPI2_MISO PD6/B2 SPI2_MISO DI_I1_1 DI_I1_2 DI_I1_1 24V_Field
24V_Field GND_Logic PD6/B2 SPI2_NSS PD6/B2 DI_I1_2 DI_I1_3 DI_I1_2 24V_Field GND_Field
GND_Field 24V_Field SPI2_NSS SPI2_SCK SPI2_NSS DI_I1_3 DI_I1_4 DI_I1_3 GND_Field VDD
GND_Field SPI2_SCK SDO_DAISY SPI2_SCK DI_I1_4 DI_I1_4 VDD GND_Logic
SDO_DAISY SDO_DAISY GND_Logic
CLT01-38SQ7 CLT03-2Q3
USB[0..5]
USB[0..5] USB[0..5]
24V
LCD_RED[0..5]
STM32F746 FMC_ADD[0..13]
3V3
3V3 GND_IN
LCD RED[0..5] LCD_GREEN[0..5] RED[0..5] ADD[0..13] FMC_DATA[0..15] ADD[0..13] VDD
VDD
5V VDD
GREEN[0..5] GREEN[0..5] DATA[0..15] DATA[0..15] 5V
VDD
5V VDD BLUE[0..5]
LCD_BLUE[0..5]
BLUE[0..5] FMC_CTRL[0..7]
FMC_CTRL[0..7]
FMC_CTRL[0..7] GND_Logic
Power
GND_Logic 5V LCD_DE SPI2_MORPHO_ISO GND_Logic GND_Logic
GND_Logic LCD_DE LCD_CLK LCD_DE SPI2_ISO_MOSI SPI2_MORPHO_ISO 5V_Field
LCD_CLK LCD_SDA LCD_CLK SPI2_ISO_MOSI ENL+ SPI2_ISO_MOSI 24V_Field 5V_Field
LCD_SDA LCD_INT LCD_SDA ENL+ OL-OFF ENL+ GND_Field 24V_Field
LCD_INT LCD_HSYNC LCD_INT OL-OFF OL-OFF GND_Field
LCD_HSYNC LCD_VSYNC LCD_HSYNC I2C1_SDA
LCD_VSYNC LCD_SCL LCD_VSYNC I2C1_SDA I2C1_SCL I2C1_SDA
LCD_SCL LCD_RST LCD_SCL I2C1_SCL UART5_RX I2C1_SCL
LCD_RESET DO_LCD_BL_CTRL LCD_RESET UART5_RX IRQ UART5_RX
DO_LCD_BL_CTRL LCD_DISP DO_LCD_BL_CTRL IRQ L+ON IRQ
LCD_DISP LCD_DISP L+ON
IO-RST
IO-RST L+ON
IO-RST
Morpho & Memory
UART4-TX
UART4_TX UART4-RX UART4_TX
UART4_RX ENCQ UART4_RX
ENCQ SPI5_WP ENCQ
SPI5_WP SPI5_NSS SPI5_WP
SPI5_NSS SPI5_HOLD SPI5_NSS MCU_RST
SPI5_HOLD SPI5_SCK SPI5_HOLD MCU_RST SPI2_SCK
SPI5_SCK SPI5_MOSI SPI5_SCK SPI2_SCK SPI2_NSS
SPI5_MOSI SPI5_MOSI SPI2_NSS SPI2_MISO
ISO8200AQ PA1
PA1
SPI5_MISO PA1 SPI2_MISO
SPI2_MORPHO_ISO SPI5_MISO BOOTO SPI5_MISO
SPI2_MORPHO_ISO BOOTO MCU_RST
VDD SPI2_MORPHO_MOSI SPI2_MORPHO_MOSI MCU_RST
GND_Logic VDD SDO_DAISY DI_FLT_Q1_OL
24V_Field GND_Logic SDO_DAISY SPI2_SCK DI_FLT_Q1_OL DI_FLT_Q1_FLT DI_FLT_Q1_OL VDD
GND_Field 24V_Field SPI2_SCK SPI2_NSS DI_FLT_Q1_FLT DI_FLT_Q1_1 DI_FLT_Q1_FLT VDD GND_Logic
GND_Field SPI2_NSS SPI2_MISO DI_FLT_Q1_1 DI_FLT_Q1_2 DI_FLT_Q1_1 GND_Logic 5V_Field
SPI2_MISO DO_Q0_EN DI_FLT_Q1_2 DI_FLT_Q1_3 DI_FLT_Q1_2 5V_Field 24V_Field
DO_Q0_EN DI_Q0_PGOOD DO_Q0_EN DI_FLT_Q1_3 DI_FLT_Q1_4 DI_FLT_Q1_3 24V_Field GND_Field
DI_Q0_PGOOD DI_Q0_FLT DI_Q0_PGOOD DI_FLT_Q1_4 DO_Q1_4 DI_FLT_Q1_4 GND_Field
DI_Q0_FLT DI_Q0_FLT DO_Q1_4 DO_Q1_3 DO_Q1_4
DO_Q1_3 DO_Q1_2 DO_Q1_3
DO_Q1_2 DO_Q1_1 DO_Q1_2
DO_Q1_1 DO_Q1_1
Q0.7
Q0.6
Q0.5
Q0.4
Q0.3
Q0.2
Q0.1
Q0.0
Q1.0
Q1.1
Q1.2
Q1.3
IPS4260L
Schematic diagrams
UM2933
page 13/42
Figure 9. STEVAL-PLC001V1 circuit schematic (2 of 9)
UM2933 - Rev 1
TP14
CLT_MOSI
CLT_MISO
CLT_SCK
CLT_CS1
C1 33pF
1
R2 R3 R4
R1
NM
220R 220R220R220R
R5
CLT01-38SQ7 C2 33pF
C3 33pF
15K GND_CLT1
GREEN
A
A
D1
D3
C
A
C
D2 C GREEN
GREEN A D4 C GREEN
C4 33pF A D5 C
GREEN A D6 C
A D7 C GREEN
VDD_CLT GREEN A D8 C
49
48
47
46
45
44
43
42
41
40
39
38
37
U1 GREEN
GND_CLT1 GND_Field
LED1
LED2
LED3
LED4
LED5
_CS
SCK
NC_17
MOSI
MISO_MISO
COMS
REF
GND_Field
R60E
INPUT
CLT01_38SQ7_TR I0 .0 R7 2K2 CLT_IN1
3
Data out= /MISO
C5 C6 1 36 C7
VDD LED6
4.7uF 100nF 2 R81K
R8 1K 2 35 22nF
J1 J2 DVR LED7
3 34
CON8 3 pin jumper NC_1 LED8
I0.0 I0 .0 8 4 33
SPM NC_16
I0.1 I0 .1 7 Data out= MISO 5
NC_2 NC_15
32 I0 .1 R9 2K2 CLT_IN2
1
I0.2 I0 .2 6 6 31
I0 .3 5 7 NC_3 COMP_4 30 C8
I0.3 COMP_1 NC_14
I0.4 I0 .4 4 R10 8 29 22nF
NC_4 NC_13
I0.5 I0 .5 3 1K 9 28
GND_Field NC_5 NC_12
I0.6 I0 .6 2 10 27
I0 .7 1 GND_CLT1 VDD_CLT 11 NC_6 NC_11 26 I0 .2 R11 2K2 CLT_IN3
I0.7 NC_7 NC_10
12 25
NC_8 NC_9
C9
CON8
3
8 bits
COMP_2
COMP_3
22nF
GND_Field
VCS
HIGH SIDE DIGITAL INPUTS J4 2
IN1
IN2
IN3
IN4
IN5
IN6
IN7
IN8
VC
3 pin jumper I0 .3 R12 2K2 CLT_IN4
13
14
15
16
17
18
19
20
21
22
23
24
C10
24V_Field
1
R194
R1940.0 0.0 R13 1K 22nF
16 bits
CLT_IN1
CLT_IN2
CLT_IN3
CLT_IN4
CLT_IN5
CLT_IN6
CLT_IN7
CLT_IN8
R15 1M5
I0 .4 R14 2K2 CLT_IN5
GND_CLT1 R16
C11 C12
120K
GND_CLT1 GND_Field 33nF 22nF
Isolation Barrier GND_Field
C18
1
Schematic diagrams
UM2933
page 14/42
Figure 10. STEVAL-PLC001V1 circuit schematic (3 of 9)
UM2933 - Rev 1
CLT03-2Q3 TP5
TP5 Isolation Barrier
R197 U3
1
VDD
U4 CLT03-2Q3 OUTP1
I1.0H 6 9 R23 0E C19 10nF 0 1 8 VDD
INATTL1 TP1 NM ANODE1 VDD
10 OUTN1 2 7 DI_I1_1
VBUF1 OUTP1 OUTN2 3 CATHODE1 V01 6
7 11 DI_I1_2
C20 INA1 OUTP1 OUTN1 4 CATHODE2 V02 5
5
I1.0L 10nF OUTN1 OUTP2 R198 ANODE2 GND
8 TAB1
INB1 OUTN1_T 0 C22
PD1 C24 4.7uF
ACPL-024L-000E
I1.1H 2 14 R24 0E C21 10nF 100nF
INATTL2 TP2
15
VBUF2 OUTP2
3 16 GND_Logic
C23 INA2 OUTP2 OUTN2
13
I1.1L 10nF OUTN2
4 TAB2
INB2 OUTN2_T
PD2
1 R23, R24, R25, R26 GND_Logic
1
C28 13 OUTN4 100nF
I1.3L 10nF OUTN2
4 TAB2
INB2 OUTN2_T 1
PD2
CLT03-2Q3 TP6
NM
GND_Logic
R201 D9 GREEN
7.5K
I1.0H A C I1.0L
INPUT D50 3.3V NM
J6
R202 D10 GREEN
7.5K
I1.1H I1.1H 1 I1.1H A C I1.1L
24V_Field I1.0H 2
I1.0H 3 D51 3.3V NM
I1.1L I1.1L 4
I1.0L I1.0L 5 R203 D11 GREEN
7.5K
6 I1.2H A C I1.2L
GND_Field CON6-2315
Schematic diagrams
UM2933
page 15/42
Figure 11. STEVAL-PLC001V1 circuit schematic (4 of 9)
UM2933 - Rev 1
24V_Field
ISO8200AQ
1
VDD C45 + C46
4.7uF/63V 10pF
VDD
2
D24 GREEN
DO_Q0_EN Q0.7 R63 7.5K A C
TAB4
U13
19
18
ISO8200AQ C48 22nF
VDD
OUT1_1
OUT1_2
VCC
TP9 17 D26 GREEN
20 OUT2_1 16 Q0.6 Q0.5 R67 7.5K A C
VDD OUT2_2 Q0.6
ESDALC6V1-1M2
NM 21 15 C49 22nF
OUT_EN OUT3_1
1
14 Q0.5 Q0.5
D27 VDD R68 220E 22 OUT3_2 D28 GREEN
SPI2_NSS SS
SPI2_SCK
R69 220E 13 Q0.4 R70 7.5K A C
23 OUT4_1 12 Q0.4
MO- A1 CLK OUT4_2 Q0.4
C50 R71 220E C51 22nF
SPI2_MORPHO_MOSI
A
10pF R72 NM 24 11
SW1 D29 MO- B3 SDI OUT5_1 10 Q0.3 D30 GREEN
SPI2_MORPHO_ISO OUT5_2 Q0.3
1437566-3 RED PGOOD 25 Q0.3 R73 7.5K A C
NM NM PGOOD 9
MO- A2 R75 100E 31 OUT6_1 8 Q0.2 C52 22nF
SDO_DAISY SDO OUT6_2 Q0.2
R74 220E
SPI2_MISO
C
32 7 Q0.1 Q0.1 D31 GREEN
FAULT OUT7_1
1
6 Q0.2 R77 7.5K A C
OUT7_2
GND_CC_1
GND_CC_2
GND_CC_3
GND_CC_4
R76 C54 C55
GND_DD
750E 33pF 33pF 5 Q0.0 Q0.0
C56 22nF
OUT8_1 4
R78 220E TP10 OUT8_2 D32 GREEN
DI_Q0_FLT
NM C53 Q0.1 R79 7.5K A C
33pF C57
TAB1
TAB2
TAB3
33pF C58 22nF
3
VDD D33 GREEN
VDD Q0.0 R80 7.5K A C GND_Field
GND_Field
A
C59 22nF
J14
VDD
GND_Logic GND_Field
Q0.7 8
Q0.6 7 D34
Q0.5 6 GREEN C60 C61
Q0.4 5 4.7uF 100nF
C
Q0.3 4
GND_Logic
Q0.2 3
Q0.1 2 R81 PLC Digital output 1-8 (high side)
750E
Q0.0 1
GND_Logic
CON8 R82 220E
PGOOD DI_Q0_PGOOD
Schematic diagrams
UM2933
page 16/42
Figure 12. STEVAL-PLC001V1 circuit schematic (5 of 9)
UM2933 - Rev 1
24V_Field
24V_Field
IPS4260L
Isolation Barrier
R27 R28 R29 R30
TP7 7.5K 7.5K 7.5K 7.5K
GREEN GREEN
A
U8
1
5V_Field D13 D14 D15 D16
U7 1 20 GND_Field GREEN
C31 D17 BAT20JFILM 2 PGND1 PGND4 19 GREEN
DO_Q1_1 PGND2 PGND3
R32 510R 1 8 100nF VZ1 3 18 VZ2
ANODE1 VDD VZ1 VZ2
C
R31 330R 2 7 R33 5.1K IN1_FLT 4 17 Q1.3
GND_Logi c R34 330R 3 CATHODE1 V01 6 R35 5.1K IN2_FLT 5 IN1 LOAD1 16 Q1.2
R36 510R 4 CATHODE2 V02 5 6 IN2 LOAD2 15 Q1.1
ANODE2 GND D18 BAT20JFILM C32 C33 7 IN3 LOAD3 Q1.0
DO_Q1_2 14
8 IN4 LOAD4 13 24V_Field PULL DOWN
ACPL-024L-000E GND_Signal TP8 1pF 1pF OL 9 SGND VCC 12 RESISTORS
5V_Field FLT 10 OL ILIM 11 C34 FOR OPEN LOAD
U9 GND_Signal FLT CoD R37 DETECTION
1
C35 D19 BAT20JFILM 21 IPS4260L R47 1uF 52K R38
IN OFF STATE
DO_Q1_3 EP
1
R46 510R 1 8 100nF GND_Signal C37 + 52K
R39 330R 2 ANODE1 VDD 7 R41 5.1K IN3_FLT R45 R40
60.4K
GND_Logi c CATHODE1 V01 IPS4260L
R42 330R 3 6 R43 5.1K IN4_FLT GND_Signal R44 J8 J9 52K 52K
4.7uF/63V
CATHODE2 V02
2
R48 510R 4 5 220K C36 2 pin jumper 2.54mm
ANODE2 GND D20 BAT20JFILM 2 pin jumper 2.54mm
DO_Q1_4
100n
ACPL-024L-000E C38 C39
GND_Signal 1pF 1pF
GND_Field
VDD GND_Signal
U10 5V_Field
GND_Signal GND_Field
VDD
C95 C40 .
GND_Logi c 5 4 R49 620R 5V_Field 1uF R51 R52
6 GND ANODE2 3 R50 200R IN4_FLT 10uF 2.5K 1K
DI_FLT_Q1_4 V02 CATHODE2 24V_Field
7 2 R53 200R IN3_FLT
DI_FLT_Q1_3 V01 CATHODE1
8 1 R54 620R
VDD ANODE1
A
C41 GND_Signal
100nF D21 D22
ACPL-024L-000E RED RED
GND_Logi c J10
U11
2 pin jumper 2.54mm
C
FLT
VDD GND_Logi c 5 4 R55 620R 5V_Field Default both J10 and J12 closed
6 GND ANODE2 3 R56 200R IN2_FLT OL
DI_FLT_Q1_2 V02 CATHODE2
7 2 R57 200R IN1_FLT
DI_FLT_Q1_1 V01 CATHODE1
8 1 R58 620R
VDD ANODE1 R195
J11
C42 D23
100nF 2 Q1.3 Q1.3 SMC30J22CA
ACPL-024L-000E 1 Q1.2 Q1.2 0.0
GND_Logi c J12
CON2 PLC DIGITAL OUTPUT 9-12 (LOW-SIDE) GND_Field 2 pin jumper 2.54mm VZ1
GND_Signal
U12 J13
GND_Logi c 2 Q1.1
VDD Q1.1
5 4 R59 620R 5V_Field CON2 1 Q1.0
GND ANODE2 Q1.0
DI_FLT_Q1_OL 6 3 R60 200R OL
7 V02 CATHODE2 2 R61 200R FLT VZ2
DI_FLT_Q1_FLT V01 CATHODE1 J26
8 1 R62 620R C43
VDD ANODE1 2 24V_Field To Field Side devices
1uF
C44 1 GND_Field C130
100nF 1nF
ACPL-024L-000E GND_Signal
CON2
GND_Logic
GND_Logi c
Schematic diagrams
UM2933
page 17/42
Figure 13. STEVAL-PLC001V1 circuit schematic (6 of 9)
UM2933 - Rev 1
2
1
STM32F746ZGT7 R184 RED.R2 R152 NM 0E
0 BT1
+2
+1
FMC_CTRL.NBL0 141 56 FMC_ADD.A10 NM 3030TR R153 0E MO- A3
FMC_CTRL.NBL1 PE0 PG0 FMC_ADD.A11 VDD PA1
142 57
PE1 PG1 USB.OVER_CURRENT SPI2_ISO_MOSI
1 87 U27C MO- A1
-
DI_I1_1 PE2 PG2 USB.POW ER_SW ITCH_ON SPI5_HOLD
2 88 C100 NM STM32F746ZGT7 NM
DI_I1_2 PE3 PG3 SPI2_MORPHO_MOSI
3
3 89 FMC_ADD.BA_0 R185 0 100nF BLUE.B5 R154 0
DI_I1_3 PE4 PG4 FMC_ADD.BA_1 SPI2_MORPHO_MOSI
4 90 34 26 RED.R5 R156 0
DI_I1_4 PE5 PG5
DI_FLT_Q1_1
5 91 RED.R7 U27B VDD RED.R4 LCD_VSYNC 35 PA0 PC0 27 R155 120 MO- A2
FMC_DATA.D4 58 PE6 PG6 92 GND_Logic 36 PA1 PC1 28 SDO_DAISY
LCD_CLK FMC_CTRL.SDCLK STM32F746ZGT7 GREEN.G2
FMC_DATA.D5 59 PE7 PG7 93 FMC_CTRL.SDNW E 37 PA2 PC2 29 FMC_CTRL.SDCKE0 SPI2_MISO
VDD
FMC_DATA.D6 60 PE8 PG8 124 VDD 6 39 40 PA3 PC3 44 FMC_CTRL.SDNE0
FMC_DATA.D7 PE9 PG9 LCD_INT VBAT VDD_2 USB.OTG_FS_VBUS DI_FLT_Q1_FLT PA4 PC4
63 125 GREEN.G3 95 72 R157 0E 41 45
FMC_DATA.D8 PE10 PG10 VDDUSB VDD_5 PA5 PC5 DO_Q0_EN
64 126 BLUE.B3 52 ENCQ R158 0 42 96
FMC_DATA.D9 PE11 PG11 VDD_3 USB.OTG_FS_ID PA6 PC6 LCD_HSYNC
65 127 BLUE.B4 16 84 R160 0E 43 97 GREEN.G6
FMC_DATA.D10 66 PE12 PG12 128 51 VSS VDD_6 121 R159 0 100 PA7 PC7 98
DI_Q0_PGOOD ENL+ DO_Q1_3
FMC_DATA.D11 67 PE13 PG13 129 130 VSS_2 VDD_8 62 USB.OTG_FS_DM R161 0E NM 101 PA8 PC8 99
FMC_DATA.D12 PE14 PG14 DI_Q0_FLT VSS_8 VDD_4 PA9 PC9 DI_FLT_Q1_OL
68 132 83 108 102 111 PC10
PE15 PG15 FMC_CTRL.SDNCAS 38 VSS_4 VDD_7 131 IRQ 103 PA10 PC10 112
R162 0 PC11
FMC_ADD.A0 10 23 RCC_OSC_IN 61 VSS_1 VDD_9 17 USB.OTG_FS_DP R163 0E NM 104 PA11 PC11 113
FMC_ADD.A1 PF0 PH0 LCD_RST VSS_3 VDD PA12 PC12 DO_Q1_4
11 24 94 144 R164 0 105 7
FMC_ADD.A2 12 PF1 PH1 107 VSS_5 VDD_10 30 IO-RST SYS_JTMS-SW DIO 109 PA13 PC13 8 RCC_OSC32_IN DI_FLT_Q1_2
FMC_ADD.A3 13 PF2 25 120 VSS_6 VDD_1 NM SYS_JTCLK-SW CLK 110 PA14 PC14 9 RCC_OSC32_OUT
FMC_ADD.A4 PF3 NRST MCU_RST VSS_7 SYS_JTDI PA15 PC15
14 138 71
FMC_ADD.A5 PF4 BOOT0 BOOTOPDR_ON VCAP_1 FMC_DATA.D2
15 143 31 106 RED.R3 46 114
18 PF5 PDR_ON 33 VSSA VCAP_2 C101 RED.R6 47 PB0 PD0 115 FMC_DATA.D3
SPI5_NSS PF6 VDDA PB1 PD1
19 32 2.2uF (Low ESR) R165 48 116
SPI5_SCK PF7 VREF+ SYS_JTDO-SW O L+ON PB2 PD2 UART5_RX
20 100 133 117 GREEN.G7
SPI5_MISO PF8 SYS_JTRST PB3 PD3
21 R205 0 GND_Logic C102 134 118
SPI5_MOSI PF9 MCU_RST PB4 PD4 DI_FLT_Q1_3 LCD_DISP LCD_DISP
22 2.2uF (Low ESR) 135 119
LCD_DE
FMC_CTRL.SDNRAS PF10 LCD_RST LCD_RESET DI_FLT_Q1_4 PB5 PD5
49 R206 NM 136 122
FMC_ADD.A6 PF11 I2C1_SCL PB6 PD6 PD6/B2
50 0 137 123
FMC_ADD.A7 PF12 I2C1_SDA PB7 PD7 FMC_DATA.D13 SPI5_W P
53 BLUE.B6 139 77
FMC_ADD.A8 54 PF13 BLUE.B7 140 PB8 PD8 78 FMC_DATA.D14
FMC_ADD.A9 55 PF14 GND_Logic VDD GREEN.G4 69 PB9 PD9 79 FMC_DATA.D15
PF15 PB10 PD10 LCD_SCL
2
GREEN.G5 70 80
PB11 PD11 DO_Q1_2
C103 L6 73 81 R167 2K7
UART4_TX VDD SPI2_NSS PB12 PD12 LCD_SDA
100nF C104 C105 600 Ohms R168 74 82 R169 2K7
SPI2_SCK PB13 PD13
3
75 85 FMC_DATA.D0
connection, connect Pin1 FMC_DATA[0..15] 0 C107 C108 C109 C113 OL-OFF 76 PB14 PD14 86 FMC_DATA.D1
DO_Q1_1 PB15 PD15 LCD_SDA
1
J22 2 PC10 and 2 of J22 and J23. VDD 100nF 100nF 100nF 100nF
DATA[0..15] 3V3
3 pin jumper VDD
FMC_DATA.D0 FMC_DATA[0..15]
1
USART3_TX FMC_DATA.D1
1
VDD
For Using IO Board e.g
P-NUCLEO-IOM01M1 through
FMC_DATA.D2
FMC_DATA.D3
GND_Logi c C110
220uF
+
C106
C111
1uF
C112
100nF GND_Logic VDD
Programming Pins
Morpho, connect Pin3 and 2 FMC_DATA.D4 100nF J23
NM TP15
2
of J22 and J23. FMC_DATA.D5 1 2 SYS_JTMS-SW DIO
UART4_RX FMC_DATA.D6 GND_Logic SYS_JTCLK-SW CLK
3 4 C114 C115 C116 C117 C118 C119 C120 C121 C122 C123
3
FMC_DATA.D7 5 6 SYS_JTDO-SW O 100nF 100nF 100nF 100nF 100nF 100nF 100nF 100nF 100nF 100nF
FMC_DATA.D8 SYS_JTRST 0 R191 7 8 SYS_JTDI
J24 2 PC11 FMC_DATA.D9 VDD GND_Logic 9 10 MCU_RST
3 pin jumper FMC_DATA.D10 GND_Logic
FMC_DATA.D11 CON10A
USART3_RX FMC_DATA.D12
1
USART3_RX
FMC_ADD.BA_0 10K GND_Logic R174 R175
ILD207T R177 RCC_OSC32_OUT
con5-strip-male FMC_ADD.BA_1 FMC_ADD[0..13] GND_Logic 200 200 R176 100 4.7pF_NPO_-+0.25pF_0402 Y1
LCD_RED[0..5] FMC_ADD.A0 100 GND_Logi c
RED[0..5] NX3215SA-32.768K
FMC_ADD.A1 VDD R178 100_1% RCC_OSC_IN
GND_EXT
FMC_ADD.A2 C125 Optional
RX_EXT
RED.R2 FMC_ADD.A3 R180 0 RCC_OSC_OUT/TEST
RED.R3 LCD_RED[0..5] FMC_ADD.A4
RED.R4 FMC_ADD.A5 R179 GND_Logic
4.7pF_NPO_-+0.25pF_0402
RED.R5 FMC_ADD.A6 10K GND_Logi c
RED.R6 FMC_ADD.A7 Y2
RED.R7 LCD_GREEN[0..5] FMC_ADD.A8 PDR_ON R181 VDD 4 3
GREEN[0..5] FMC_ADD.A9
FMC_ADD.A10 10K C126
GREEN.G2 LCD_GREEN[0..5] FMC_ADD.A11 GND_Logic R183 10k 1 2
NM
GREEN.G3 R182
GREEN.G4 FMC_CTRL[0..7] MCU_RST 100nF ECS-2520MV-250-BN-TR
VDD
GREEN.G5 GND_Logic GND_Logic
FMC_CTRL[0..7] USB[0..5] To be mounted to enable real-time clock
GREEN.G6
LCD_BLUE[0..5] FMC_CTRL[0..7] 10K
GREEN.G7 FMC_CTRL.NBL0
FMC_CTRL.NBL1 USB.POW ER_SW ITCH_ON USB[0..5]
FMC_CTRL.SDCLK USB.OVER_CURRENT USB[0..5]
BLUE[0..5] FMC_CTRL.SDCKE0 USB.OTG_FS_VBUS
BLUE.B2
BLUE.B3 FMC_CTRL.SDNE0 USB.OTG_FS_DP C127 D49 SW 2
BLUE.B4 FMC_CTRL.SDNRAS USB.OTG_FS_DM 1437566-3
BLUE.B5 FMC_CTRL.SDNCAS USB.OTG_FS_ID 100nF ESDALC6V1-1M2
BLUE.B6 LCD_BLUE[0..5] FMC_CTRL.SDNW E
BLUE.B7
GND_Logic
Schematic diagrams
UM2933
page 18/42
Figure 14. STEVAL-PLC001V1 circuit schematic (7 of 9)
UM2933 - Rev 1
Morpho Connectors
VDD 1 86
C69 FMC_DATA.D0 2 VDD VSS_3 85 FMC_DATA.D15
100nF 3 DQ0 DQ15 84
C70 FMC_DATA.D1 4 VDDQ VSSQ_7 83 FMC_DATA.D14 VDD
100nF FMC_DATA.D2 5 DQ1 DQ14 82 FMC_DATA.D13 GND_Logic
J17 con38-2x19-strip-male (MORPHO) VDD 6 DQ2 DQ13 81
VDD 1 2 J18 con38-2x19-strip-male (MORPHO) FMC_DATA.D3 7 VSSQ VDDQ_7 80 FMC_DATA.D12
VDD DQ3 DQ12
3 4 UART5_RX R104 NM OUTI Q 1 2 R115 NM FMC_DATA.D4 8 79 FMC_DATA.D11 C71
I NCQ R106 NM ENCQ GND_Logi c DQ4 DQ11
5 6 I2C1_SCL
R105 NM 3 4 9 78 100nF
OUTCQ R109 NM UART4_RX UART4_TX FMC_DATA.D5 VDDQ_1 VSSQ_6 FMC_DATA.D10
7 8 I2C1_SDA
R108 NM 5 6 10 77 VDD
UART4_RX FMC_DATA.D6 DQ5 DQ10 FMC_DATA.D9
9 10 MCU_RST 7 8 C72 11 76
11 12 R186 NM GND_Logi c 9 10 VDD 100nF 12 DQ6 DQ9 75 GND_Logi c
OL-OFF R95 13 14 VDD SPI2_SCK R113 NM 11 12 R118 NM FMC_DATA.D7 13 VSSQ_1 VDDQ_6 74 FMC_DATA.D8
SPI2_SCK ENCQ DQ7 DQ8
NM 15 16 SPI2_ISO_MOSI 13 14 R122 NM 14 73 C73
GND_Logic IO-RST GND_Logi c NC NC_5
17 18 SPI2_MORPHO_ISO
MO- A3 R121 NM 15 16 R123 NM IO-RST 15 72 100nF
19 20 MO- B3 R126 NM 17 18 FMC_CTRL.NBL0 16 VDD_1 VSS_2 71 FMC_CTRL.NBL1
SPI2_MISO DQM0 DQM1
UART4_RX 21 22 R129 NM 19 20 C74 FMC_CTRL.SDNWE 17 70
SPI2_NSS *WE NC_4
R96 NM 23 24 GND_Logi c R130 120 21 22 R131 NM FMC_CTRL.SDNCAS 18 69 GND_Logic
PA1 *CAS NC_3
25 26 23 24 R134 NM IRQ 100nF FMC_CTRL.SDNRAS 19 68 FMC_CTRL.SDCLK
IRQ FMC_CTRL.SDNE0 *RAS CLK FMC_CTRL.SDCKE0
VDD 27 28 I NT IRQ 25 26 R135 NM L+ON 20 67
29 30 R187 NM R189 NM 27 28 OUTI Q R136 NM FMC_ADD.A11 21 *CS CKE 66 FMC_ADD.A9
NM UART5_RX A11 A9
31 32 29 30 OUTI Q R138 NM UART5_RX GND_Logic FMC_ADD.BA_0 22 65 FMC_ADD.A8
R98 NM 33 34 SPI2_SCK 31 32 FMC_ADD.BA_1 23 BA0 A8 64 FMC_ADD.A7
ENL+ 35 36 CLTD VDD ENL+ R190 NM 33 34 R139 NM FMC_ADD.A10 24 BA1 A7 63 FMC_ADD.A6
ENL+ FMC_ADD.A0 A10 A6 FMC_ADD.A5
IRQ 37 38 R188 NM 35 36 25 62
R99 NM 37 38 GND_Logic FMC_ADD.A1 26 A0 A5 61 FMC_ADD.A4
VDD FMC_ADD.A2 27 A1 A4 60 FMC_ADD.A3
A2 A3
The resistors to be mounted appropiately to use STEVAL-IOM001V1 or X-NUCLEO-IOD04A1 28 59 VDD
R100 10K_1 29 DQM2 DQM3 58 R101 10K_1
30 VDD_2 VSS_1 57
C75 R114 10K_1 31 NC_1 NC_2 56 R103 10K_1
100nF 32 DQ16 DQ31 55
VSSQ_2 VDDQ_5
Debug LEDs
R107 10K_1 33 54 R116 10K_1 C76
VDD R110 10K_1 34 DQ17 DQ30 53 R111 10K_1 C77
GND_Logi c 35 DQ18 DQ29 52 100nF 100nF
R112 10K_1 36 VDDQ_2 VSSQ_5 51 R117 10K_1
C78 R119 10K_1 37 DQ19 DQ28 50 R120 10K_1 VDD
VDD VDD VDD 100nF 38 DQ20 DQ27 49
R124 10K_1 39 VSSQ_3 VDDQ_4 48 R125 10K_1
VDD DQ21 DQ26
U20 R127 10K_1 40 47 R128 10K_1 GND_Logic
OL-OFF W25X10CLSNIG VDD GND_Logic 41 DQ22 DQ25 46 C79
FMC_DATA[0..15] VDD R132 10K_1 42 VDDQ_3 VSSQ_4 45 R133 10K_1 100nF
R137 1 8 43 DQ23 DQ24 44
L+ON SPI5_NSS /CS VCC DATA[0..15] FMC_ADD[0..13] VDD_3 VSS
330E 2 7 SPI5_HOLD
SPI5_MISO DO_IO1_ /HOLD FMC_DATA.D0 FMC_DATA[0..15]
R94
SPI5_WP 3 6 C80
/WP CLK SPI5_SCK FMC_DATA.D1 ADD[0..13]
330E 4 5 100nF C81
GND DI_IO0_ SPI5_MOSI FMC_DATA.D2 FMC_ADD.BA_0 FMC_ADD[0..13] 100nF GND_Logic
A
FMC_DATA.D3 FMC_ADD.BA_1
A
GND_Logic GND_Logic
Schematic diagrams
UM2933
page 19/42
Figure 15. STEVAL-PLC001V1 circuit schematic (8 of 9)
UM2933 - Rev 1
LCD
5V
L1 L2 D35 LED+
1 2 1 2
LED+
0 0 0
0 0 0
1
10nF 10nF 4.7uF
6
U14
VO
SW
GND_LCD
TP11
1 2
VI RSET
5
5V R83 4K7 7 NC
5V EN
5V 4
FB
PGND
GND
DO_LCD_BL_CTRL
R84 22k 1 Q1
2STR1160
9
STLD40DPUR R85 R86
10_1%
L3 GND_LCD 100K
1 2 VDD
0 0
U15
600 Ohms
1
1 2
GND_Logi c GND_LCD 3 1 2 4
3 4 VDD
R87 4K7 5 6 R88 4K7
U16 LCD_RED2 7 5 6 8 LCD_RED3
1 16 TP18 R93 4K7 LCD_RED4 9 7 8 10 LCD_RED5
2 IN1 OUT1 15 LCD_DE2 LCD_RED6 11 9 10 12 LCD_RED7
LCD_DE IN2 OUT2 11 12
1
3 14 LCD_VSYNC2 R89 4K7 13 14 R90 4K7
LCD_VSYNC IN3 OUT3 13 14
4 13 LCD_HSYNC2 LCD_GREEN2 15 16 LCD_GREEN3 C67 + C68
LCD_HSYNC IN4 OUT4 LCD_DISP2 LCD_GREEN4 17 15 16 LCD_GREEN5 4.7uF
LCD_DISP 5 12 18 100nF
6 IN5 OUT5 11 LCD_CLK2 LCD_GREEN6 19 17 18 20 LCD_GREEN7
LCD_CLK IN6 OUT6 19 20
2
7 10 LCD_BLUE7 R91 4K7 21 22 R92 4K7
GND
29 30 LCD_CLK2
LCD_BLUE[0..5] GND_Logic LCD_DISP2 31 29 30 32 LCD_HSYNC2
LCD_VSYNC2 33 31 32 34 LCD_DE2
LCD_BLUE[0..5] 35 33 34 36
BLUE[0..5] 35 36
GND_Logic 37 38
LCD_RESET 37 38 LCD_INT
BLUE.B6 LCD_SCL 39 40
39 40 LCD_SDA
BLUE.B7
GND_Logic
GREEN[0..5] BLUE.B5 1
IN1 OUT1
16 LCD_BLUE5 Connector for TFT Display andTouch panel UI (RK043FN02H-CT)3.5" or equivalent
BLUE.B4 2 15 LCD_BLUE4
LCD_RED[0..5] GREEN.G2 LCD_GREEN[0..5] BLUE.B3 3 IN2 OUT2 14 LCD_BLUE3
GREEN.G3 BLUE.B2 4 IN3 OUT3 13 LCD_BLUE2
GREEN.G7 5 IN4 OUT4 12 LCD_GREEN7
RED[0..5] LCD_RED[0..5] U18 IN5 OUT5
GREEN.G6 6 11 LCD_GREEN6
1 16 LCD_GREEN3 GREEN.G5 7 IN6 OUT6 10 LCD_GREEN5
GND
2 IN1 OUT1 15 LCD_GREEN2 GREEN.G4 8 IN7 OUT7 9 LCD_GREEN4
RED.R7 3 IN2 OUT2 14 LCD_RED7 IN8 OUT8
RED.R6 4 IN3 OUT3 13 LCD_RED6 EMIF08-LCD04M16
IN4 OUT4
17
RED.R5 5 12 LCD_RED5
RED.R4 6 IN5 OUT5 11 LCD_RED4
RED.R3 7 IN6 OUT6 10 LCD_RED3
GND
GND_Logic
Schematic diagrams
UM2933
page 20/42
Figure 16. STEVAL-PLC001V1 circuit schematic (9 of 9)
UM2933 - Rev 1
Power
Provision for different footprint
Q4
DC-DC CONVERTER Isolation
STL42P6LLF6 24V_Field
terminal block F1 U29 NCS1S2405SC
24V GND_Logic
SF-0603HI700M-2 (7A FUSE) 5 3 L4 6 2 5V
J19 +VOUT +VIN
6 2 1 2 VDD
24V_Field 7
0 0
2 7 1 0 0
1
1 8 100Ohms -VOUT -VIN
C84 3
SMAJ15A-TR R142 GND_Field CTRL R143
CON2
1
4n7/3kV D38 C85 NM 1K
7.5k 4.7uF +
NM
USB.POWER_SWITCH_ON
1
D39 C86 R144 470K
A
1
1uF + C87 100uF
EARTH SM15T33CA C89 + D41 Non Isolated
GREEN
J20 C91 C90 D40 NM R146
4.7uF/63V
Power Source
2
1 R145 NM 100nF C88 R192 NM
for Demo Mode
2
4n7/3kV 330K BLUE 47K
2
Surge test Pad
NM
C
5V U22
U21 USB.OVER_CURRENT
5 1 1
IN OUT 2 GND
1
4 3
GND_Field EN FAULT 2 3 DM
DC-DC CONVERTER GND
Isolation R147 C92 4 DP
U24 5V U23 LM7805-d2pak 10K STMPS2151STR 4.7uF 5 ID
NCS1S2405SC TP17 VBUS
NM
24V_Field 2 6 24V_Field 1 3 5V_Field 6
+VIN +VOUT IN OUT 5V_Field M1
7
GND
8 M2
1 7
-VIN -VOUT 9 M3
M4
1
3 C93 GND_Logic
CTRL
4
0.33 D42 C94
USB.OTG_FS_VBUS
USB_micro_AB
GND_Field SMA6F5.0A 10nF GND_Logic
D43
GND_Logic TP12 GND_Logic
GND_Field
ESDA7P120-1U1M
3USB.OTG_FS_VBUS
1
USB.OTG_FS_ID
GND_Logic
GND_Field
5V U25
TP13 USB.OTG_FS_DP 1 6 D44
NM USB.OTG_FS_DM 2 DP1 DP6 5
5V DM2 DM5 ESDALC6V1-1M2
5V 3 4
GND NC GND_Logi c
VDD
3
ECMF02_2AMX6
D45 D46 NM
3V3
5V TO 3.3V
STPS5L25B-TR STPS5L25B-TR VDD GND_Logic
R148
VDD 47K R149
4
USB[0..5] 330E
A
L7 U26 L5
USB.POWER_SWITCH_ON USB[0..5]
1 2 1 5 1 2 D47
0
0
IN OUT 0
0
USB.OVER_CURRENT Amber
470E USB.OTG_FS_DM
NC
3 C
C97 USB.OTG_FS_ID
LDK220M33R C99
2
C96 1 Q5
A
1uF 4.7uF 10nF 2STR1160
C98 D48 R151
10uF
2
22K
GREEN
GND_Logic
C
GND_Logic
GND_Logic
GND_Logic
Schematic diagrams
UM2933
page 21/42
UM2933
Bill of materials
5 Bill of materials
Battery
Keystone
1 1 BT1 3030TR holder (not 3030TR
Electronics
mounted)
C1 C2 C3 C4 33 pF, 0402 (1005
Ceramic
2 8 C53 C54 C55 Metric), 10 V, Wurth Elektronik 885012005028
capacitors
C57 +/-5%, SMD
4.7 µF, 0805
Ceramic
3 1 C5 (2012 Metric), 25 Wurth Elektronik 885012107018
capacitor
V, +/-20%, SMD
100 nF, 0402
C6,C14,C31 Ceramic
4 4 (1005 Metric), 10 Wurth Elektronik 885012105010
C35 capacitors
V, +/-20%, SMD
C7 C8 C9
C10 C12 C13
22 nF, 0402 (1005
C17 C18 C47 Ceramic Murata
5 16 Metric), 50 V, GCM155R71H223JA55D
C48 C49 C51 capacitors Electronics
+/-5%, SMD
C52 C56 C58
C59
33 nF, 0402 (1005
Ceramic Murata
6 1 C11 Metric), 50 V, 81-GCM155R71H333KE2D
capacitor Electronics
+/-10%, SMD
C16 C24 C29
C41 C42 C44
C61 C67 C69
C70 C71 C72
C73 C74 C75
C76 C77 C78
C79 C80 C81
C82 C100 100 nF, 0402
C103 C105 (1005 Metric), 10 Ceramic
7 43 Wurth Elektronik 885012205018
C106 C107 V/6.3 V, +/-10%, capacitors
C108 C109 SMD
C112 C113
C114 C115
C116 C117
C118 C119
C120 C121
C122 C123
C126 C127
10 µF 0603,
Ceramic
8 1 C15 (1608 Metric), 6.3 Wurth Elektronik 885 012 106 006
capacitors
V, +/-20%, SMD
C19 C21 C25 10nF, 0402 (1005
Ceramic
9 7 C27 C62 C64 Metric), 16 V/25 Wurth Elektronik 885012205031/885012205050
capacitors
C97 V, +/-10%, SMD
Ceramic
10 nF, 0402 (1005
capacitor
10 1 C66 Metric), 50 V, Wurth Elektronik
(not
SMD
mounted)
10 nF, 0402 (1005
C20 C23 C26 Ceramic
11 4 Metric), 100 V, Yageo CC0402KRX7R0BB103
C28 capacitors
+/-10%, SMD
4.7 µF, 0805
C22 C30 C60 Ceramic
12 5 (2012 Metric), 6.3 Wurth Elektronik 885012207002
C83 C92 capacitors
V, +/-10%, SMD
Capacitor
220 µF SMD,
33 1 C110 (not Wurth Elektronik -
6032-28, 10 V
mounted)
1 µF, 0402 (1005
Ceramic
34 2 C104 C111 Metric), 6.3 V, Taiyo Yuden JMK105BJ105KV8F
capacitors
SMD
4.7 pF NPO -
+0.25 pF, 0402 Ceramic
35 2 C124 C125 Yageo CC0402CRNPO9BN4R7
(1005 Metric), 6.3 capacitors
V, SMD
Ceramic
100 nF, 0402
capacitor
36 1 C129 (1005 Metric), 10 Wurth Elektronik -
(not
V, SMD
mounted)
1 nF 0603, (1608
Ceramic
37 1 C130 Metric), 63 V, Kemet C0603C102KMRECAUTO
capacitor
SMD
D1 D2 D3 D4
D5 D6 D7 D8
D9 D10 D11
Green, 0603
D12 D13 D14 Standard
38 25 (1608 Metric), 2 Lumex SML-LXFP0603SUGCTR
D15 D16 D24 LEDs
V, 5 mA, 30 mW
D25 D26 D28
D30 D31 D32
D33 D48
Green, 0603
Standard
39 1 D41 (1608 Metric), 1.8 Kingbright APT1608LZGCK
LED
V, 2 mA
23 V, 1 A
general
SC-90,
D17 D18 D19 purpose
40 4 SOD-323F, 23V, ST BAT20JFILM
D20 signal
1A
Schottky
diode
Red, 0603, (1608
41 3 D21 D22 D29 Metric), 2 V (VF), LEDs Lumex SML-LXFP0603SIC-TR
5 mA, 30 mW
SMC30J22CA,
3000 W, 22 V
42 1 D23 DO-214AB, SMC, ST SMC30J22CA
TVS in SMC
VRM, 22 V
Single line
low
capacitance
Transil
ESDALC6V1-1M2 transient
43 3 D27 D44 D49 ST ESDALC6V1-1M2
, SOD-882, 50 W surge voltage
suppressor
(TVS) for
ESD
protection
Amber, 0603
Standard
44 3 D34 D37 D47 (1608 Metric), 2 Wurth Elektronik 150060AS75020
LEDs
V, 20 mA, 48 mW
Blue, 0603 (1608
Standard
45 2 D36 D40 Metric), 2.8 V, 5 Kingbright APT1608VRCXF/A-5MAV
LEDs
mA
SOD-123, 900mv Zener diode
D50,D51,D52, ON
46 4 @ 10mA, 7.5uA (not MMSZ4684T1G
D53 Semiconductor
@1.5 V, 500 mW mounted)
40 V, 1 A
STPS1L40M, STmite low
47 1 D35 DO-216AA, 460 drop power ST STPS1L40M
mV @ 1 A Schottky
rectifier
SMAJ15A-TR,
400 W TVS
48 1 D38 DO-214AC, SMA, ST SMAJ15A-TR
in SMA
400 W
SM15T33CA, 1500 W, 33 V
49 1 D39 ST SMCJ33CA-TR
DO-214AB, SMC TVS in SMC
SMA6F5.0A,
600 W, 5 V
DO-221AC, SMA
50 1 D42 TVS in SMA ST SMA6F5.0A
Flat Leads, 5 V,
Flat
600 W
ESDA7P120-1U1 High-power
M, 0603 (1610 transient
51 1 D43 ST ESDA7P120-1U1M
Metric), 1400 W, voltage
1.4 kW suppressor
STPS5L25B-TR,
25 V, 5 A low
TO-252-3, DPak
drop power
52 2 D45 D46 (2 Leads + Tab), ST STPS5L25B-TR
Schottky
SC-63, 470 mV
rectifier
@5A
SF-0603HI700M-
2 (7 A fuse), 0603 High inrush
53 1 F1 Bourns Inc. SF-0603HI700M-2
(1608 Metric), 32 multilayer
V
Fixed
CON8, 8P 5.0
54 2 J1 J14 terminal Wurth Elektronik 691244510008
8mm 90DEG
blocks
CONN
55 2 J2 J4 3 pin jumper HEADER .10 Wurth Elektronik 613 003 111 21
0 STR 3POS
6-way PCB
56 2 J6 J7 CON6-2315 terminal Wurth Elektronik 691231510006
block
2-pin jumper 2.54
57 4 J8 J9 J10 J12 Jumpers Wurth Elektronik 61300211121
mm
Fixed
J11 J13 J19 5.08 mm pitch,
58 4 terminal Phoenix Contact 1711725
J26 250 V, 24 A
blocks
con38-2x19-strip- Connector
59 2 J17 J18 Samtec Inc. TSM-119-01-F-DV
male (morpho) headers
PCB PAD Sullins
60 1 J20 Surge test Pad (not Connector PRPC001SAAN-RC
mounted) Solutions
3-pin jumper, 2.54 Connector
61 2 J22 J24 Wurth Elektronik 61300311121
mm headers
Connector
62 1 J23 CON10A CNC Tech 3220-10-0100-00
header
Connector
63 1 J25 5-pin 2.54 mm Wurth Elektronik 691210910005
header
600 Ohms, 0603
64 3 L1 L3 L6 (1608 Metric), Ferrite beads Fair-Rite 2506036017Y0
400 mA
R65 R100
R101 R103
R107 R110
R111 R112
R114 R116 10 K, 0402 (1005
R117 R119 Metric), 50 V, Chip
91 24 Yageo RC0402FR-7D10KL
R120 R124 0.063 W, 1/16 W, resistors
R125 R127 +/-1%
R128 R132
R133 R147
R171 R179
R182 R183
R72 R75 R95
R96 R98 R99
R104 R105
R106 R108
R109 R113
R115 R118
R121 R122
0402 (1005
R123 R126
Metric), 50 V, Chip
92 35 R129 R131 Yageo NM
0.063 W, 1/16 W, resistors
R134 R135
+/-1%
R136 R138
R139 R154
R157 R170
R181 R186
R187 R188
R189 R190
R192
750 E, 0402
(1005 Metric), 50 Chip
93 2 R76 R81 KOA Speer SG73P1ETTP7500F
V, 0.125 W, 1/8 resistors
W, +/-1%
R83 R87 R88 4K7, 0402 (1005
R89 R90 R91 Metric), 50 V, Chip
94 9 Yageo RC0402FR-7D4K7L
R92 R93 0.063 W, 1/16 W, resistors
R193 +/-1%
100 K, 0402
(1005 Metric), 50
95 1 R85 Chip resistor Yageo RC0402FR-10100KL
V, 0.063 W, 1/16
W, +/-1%
10_1% 0402
(1005 Metric) 50 Anti sulphur Stackpole
96 1 R86 RMCS0402FT10R0
0.063 W, 1/16 W chip resistor Electronics Inc
1%
47 K 0402 (1005
R97 R140 Metric) 50 V Chip
97 4 Yageo RC0402FR-1347KL
R146 R148 0.063 W, 1/16 W resistors
±1%
470 K 0402 (1005
Metric) 50 V
98 1 R144 Chip resistor Yageo RC0402FR-07470KL
0.063 W, 1/16 W
±1%
330K 0402 (1005
Metric) 50 V
99 1 R145 Chip resistor Yageo RC0402FR-07330KL
0.063 W, 1/16 W
±1%
470 0603 (1608
100 1 R150 Metric) 50 V 0.1 Chip resistor Yageo RC0603JR-07470RL
W, 1/10 W ±5%
Quad low-
IPS4260L, 20-
side
116 1 U8 TSSOP (0.173", ST IPS4260L
intelligent
4.40mm Width)
power switch
Galvanic
isolated octal
high side
ISO8200AQ,
117 1 U13 smart power ST ISO8200AQ
TFQFPN32
solid state
relay with
SPI interface
White LED
STLD40DPUR, 8- power supply
118 1 U14 VDFN Exposed for large ST STLD40DPUR
Pad display back-
light
FH12S-40S-05SH Hirose Electric
119 1 U15 Connector FH12S-40S-0.5SH(55)
55 Co Ltd
8-line L-C
EMIF08-
EMI filter and
LCD04M16,
ESD
120 3 U16 U17 U18 0.130" L x ST EMIF08-LCD04M16
protection for
0.053" W (3.30
display
mm x 1.35 mm)
interfaces
IS42S32400F-7T
Integrated
LI-TR, 86-TFSOP SDRAM
121 1 U19 Silicon Solution IS42S32400F-7TLI-TR
(0.400", 10.16 memory
Inc
mm Width)
W25X10CLSNIG,
Serial Flash Winbond
122 1 U20 8-SOIC (0.154", W25X10CLSNIG
memory Electronics
3.90 mm Width)
Enhanced
STMPS2151STR, single
SC-74A, channel
123 1 U21 ST STMPS2151STR
SOT-753, power
SOT23-5L switches (not
mounted)
Connector
124 1 U22 USB_micro_AB Molex 0475900001
receptacle
LM7805-d2pak,
Positive
TO-263-3, D²Pak
125 1 U23 voltage ST L7805CD2T-TR
(2 leads + tab),
regulator IC
TO-263AB
NCS1S2405SC,
0.86" L x 0.32" W
DC-DC Murata Power
126 1 U24 x 0.45" H (21.9 NCS1S2405SC
converter Solutions Inc.
mm x 8.2 mm x
11.3 mm)
Common-
mode filter
and ESD
ECMF02_2AMX6, protection for
127 1 U25 6-UFQFN, 200 USB 2.0 and ST ECMF02-2AMX6
mA MIPI/MDDI
interfaces
(not
mounted)
200 mA low
LDK220M33R,
quiescent
SC-74A,
128 1 U26 current and ST LDK220M33R
SOT-753,
low noise
SOT23-5L
LDO
ILD207T, 8-SOIC Vishay
129 1 U28 (0.154", 3.90 mm Opto-isolator Semiconductor ILD207T
Width) Opto Division
REM2-2405S,
DC DC
0.86" L x 0.32" W
CONVERTE
x 0.45" H (21.9
130 1 U29 R 5V /2W RECOM REM2-2405S
mm x 8.2 mm
(not
x 11.3 mm), 400
mounted)
mA
NX3215SA-32.76
NDK America, NX3215SA-32.768K-EXS00A-
131 1 Y1 8K, 2-SMD, no Crystal
Inc. MU00003
lead
ECS-2520MV-250 Standard
132 1 Y2 -BN-TR 4-SMD, clock ECS Inc. ECS-2520MV-250-CN-TR
No lead oscillator
3.5" LCD
None ( Not RK035HQ02-
TFT Rocktech
133 1 shown in CT814B, 3.5" RK035HQ02-CT814B
connected Displays Limited
Schematic) LCD TFT
via U15
None ( Not WR-PHD 2.54 Headers and
134 6 shown in mm jumper with wire Wurth Elektronik 60900213421
Schematic) test point housings
None ( Not
Nylon stand- Keystone
135 8 shown in M3 thread 25505
off Electronics
Schematic)
None ( Not
Screws and Keystone
136 8 shown in M3 Nylon Nut 4688
fasteners Electronics
Schematic)
6 Regulatory compliance
Formal Product Notice Required by Industry Canada Innovation, Science and Economic Development
Canada compliance:
For evaluation purposes only. This kit generates, uses, and can radiate radio frequency energy and has not been
tested for compliance with the limits of computing devices pursuant to Industry Canada (IC) rules.
À des fins d'évaluation uniquement. Ce kit génère, utilise et peut émettre de l'énergie radiofréquence et n'a pas
été testé pour sa conformité aux limites des appareils informatiques conformément aux règles d'Industrie Canada
(IC).
7 Board versions
Appendix A MCU interfaces mapped with devices and board terminal blocks
Table 4. List of MCU interfaces mapped with devices and board terminal blocks
Device
Board MCU Other MCU side Jumper
Devices Device pins LED side test Jumpers
interface interface devices test point description
point
PB12,PB1
CS,SCK,MO
3,PC1,PC
SI, MISO
2
I0.0,I0.1,I0.
2,I0.3,I0.4,I
0.5,
I0.6,I0.7
LED1,LED2, D1,D2,
LED3,LED4, D3,D4,
LED5,LED6, D5,D6,
LED7, LED8 D7,D8
A6 (U2), TP2-
PC2 GND1 (SPI2_MISO
(U2) ), TP3- Gnd
TP1-
CLT01_38SQ7 J2,J4
(CLT_MISO
B6(U2), ), TP4
MISO,
GND2(U2 (F.Gnd),
COMs, REF
) TP14-
(CLT_MISO
)
J2 - Pin1,2
Short
(MISO); J4-
pin3-2 short
( 8 bit
DVR, SPM mode).
J2&J4 pin 1
and 3 are
connected
to
GND,VDD
(OUTP1,
OUTN1,
OUTP2,
OUTN2)- U4 PE2 ,PE3,
(OUTP3, PE4,PE5
OUTN3,
OUTP4,OUT
N4)- U5
I1.0H/L-
I1.3H/L
CLT03_2Q3 (INATTL1,IN
A1, INB1;
INATTL2,
D9,D10,
INA2,INB2)-
D11,D1
U5 INATTL1,
2
INA1,INB1;
INATTL2,INA
2, INB2)-U6
TP5 (Near
OUTP1,OUT U3),
P4 TP6(Near
U6)
Device
Board MCU Other MCU side Jumper
Devices Device pins LED side test Jumpers
interface interface devices test point description
point
SPI2_NSS,S
PB12,PB1
PI2_SCK,SPI
3,PC1,PC
2_MOSI,
2
SPI2_MISO
Q0.0,Q0.1,
Q0.2,Q0.3,
Q0.4,
Q0.5,Q0.6,
Q0.7
OUT8_1 &
OUT8_2;OU
T8_1 &
ISO8200AQ OUT8_2;OU
T8_1 &
OUT8_2;OU
D33,D3
T8_1 &
2,D31,D
OUT8_2;OU
30,D28,
T8_1 &
D26,D2
OUT8_2;OU
5,D24
T8_1 &
OUT8_2;OU
T8_1 &
OUT8_2;OU
T8_1 &
OUT8_2;
CLK, SDI TP9 ,TP10
PB15,PD1
DO_Q0_1--
1,PC8,PC
DO_Q0_4
12
Q1.0,Q1.2,
Q1.3,Q1.4
LOAD4,
D16,D1
LOAD3,
5,D14,
LOAD2,
IPS4260L D13 J8,J9,J10,J12
LOAD1
IN1, IN3 TP7, TP8
J8 and J9
open in
LOAD1,LOA
case of no
D2
load. J10
(VZ1&VZ2)
closed and
J12 open.
J22: Pin1-
PC10,PC1
USART3_T
1; for J22- Pin 1,2
X, Pin2-
UART5_R Short(USART3_
PC10(MCU)
X PD2 TX) & Pin 2,3
, Pin3-
(Schemati Short(UART4_T
UART4_TX;
UART c has no X); J24- Pin 1,2
J24:Pin1-
informatio Short(USART3_
USART3_R
n RX) & Pin 2,3
X, Pin2-
regarding Short(UART4_R
PC11(MCU)
UART5_T X)
, Pin3-
X)
UART4_RX
LCD_BL_CT PA0(TIME EN(U14
LCD_DISPLAY RL R 2) pin 7)
Device
Board MCU Other MCU side Jumper
Devices Device pins LED side test Jumpers
interface interface devices test point description
point
(PA1,PB0,
PA5,PC0,
PD1,PG7),
RED (R2-
(PA6,PG1
R7), GREEN
0,PB10,P
(G2-G7),
B11,PC7,
BLUE (B2-
PD3),
B7)
(PG11,PG
12,PA3,PB
8,PB9)
LCD_RST,
LCD_INT,
LCD_DISPLAY LCD_CLK,
PH1,PG9,
LCD_HSYNC
PG7,PC6,
,
PA4,PD5,
LCD_VSYNC
PD13,PD1
, LCD_DISP,
2,PF10
LCD_SDA,
LCD_SCL,
LCD_DE
VO(U14
pin 6),
GND& TP11, TP18
PGND(U1
4 Pin 3,9)
PB14, D36,D3
Debug LED
PB2 7
Revision history
Table 5. Document revision history
Contents
1 Getting started . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
1.1 Safety precautions for use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
1.2 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
1.3 Hardware architecture . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
1.4 Board connections and components. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
1.5 Main components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
1.5.1 CLT01-38SQ7 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
1.5.2 CLT03-2Q3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
1.5.3 ISO8200AQ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
1.5.4 IPS4260L . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
1.5.5 STM32F746ZG . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
1.6 Digital inputs and outputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
1.7 Power distribution on the board. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
1.8 MCU interfaces and pin allocation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
1.9 External memory interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
1.10 Jumper selection, LED indicators and test points . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
2 How to run the evaluation board with the preloaded firmware . . . . . . . . . . . . . . . . . . . . .11
3 Firmware overview and architecture . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
4 Schematic diagrams . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
5 Bill of materials . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22
6 Regulatory compliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32
7 Board versions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .33
Appendix A MCU interfaces mapped with devices and board terminal blocks. . . . . . . . . .34
Appendix B Options for customization. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .37
B.1 Daisy chain connection on the STM32F746ZG SPI2 peripheral . . . . . . . . . . . . . . . . . . . . . . . 37
B.2 Possible additions to the board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .38
List of tables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .40
List of figures. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .41
List of tables
Table 1. LED indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Table 2. STEVAL-PLC001V1 bill of materials . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Table 3. STEVAL-PLC001V1 versions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Table 4. List of MCU interfaces mapped with devices and board terminal blocks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Table 5. Document revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
List of figures
Figure 1. STEVAL-PLC001V1 evaluation board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Figure 2. STEVAL-PLC001V1 functional block diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Figure 3. STEVAL-PLC001V1 external connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Figure 4. STEVAL-PLC001V1 top components. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Figure 5. STEVAL-PLC001V1 bottom components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Figure 6. Power and logic connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Figure 7. STSW-PLC001 block diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Figure 8. STEVAL-PLC001V1 circuit schematic (1 of 9) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Figure 9. STEVAL-PLC001V1 circuit schematic (2 of 9) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Figure 10. STEVAL-PLC001V1 circuit schematic (3 of 9) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Figure 11. STEVAL-PLC001V1 circuit schematic (4 of 9) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Figure 12. STEVAL-PLC001V1 circuit schematic (5 of 9) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Figure 13. STEVAL-PLC001V1 circuit schematic (6 of 9) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Figure 14. STEVAL-PLC001V1 circuit schematic (7 of 9) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Figure 15. STEVAL-PLC001V1 circuit schematic (8 of 9) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Figure 16. STEVAL-PLC001V1 circuit schematic (9 of 9) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Figure 17. Options to include devices in a daisy chain connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37