Professional Documents
Culture Documents
CLASS TEST
Path to success KOTA (RAJASTHAN )
R2
R1
æ I + mR R ö æ I + mR R ö
(A) f = ç I + mR 2 ÷ T , towards right (B) f = ç I + mR 2 ÷ T , towards left
1 2 1 2
è 2 ø è 2 ø
æ I - mR R ö æ I - mR R ö
(C) f = ç I + mR 2 ÷ T , towards right (D) f = ç I + mR 2 ÷ T , towards left
1 2 1 2
è 2 ø è 2 ø
3. Two strings support a uniform rod as shown. String at end B is cut. Which of the following is true just
after cut
[I] initial acceleration of A is vertical
[II] initial acceleration of A is horizontal
[III] initial acceleration of centre of mass of rod is vertical
[IV] initial acceleration of centre of mass of rod is horizontal
(A) [I] & [II] (B) [II] & [III] (C) [III] & [IV] (D) [I] & [IV]
PHYSICS / Class Test # 45 E-1/5
TM
(A) Change in angular momentum of the ball about origin in any time interval is same from both frames.
(B) Work done by friction on the ball in any time interval is same from both frames
(C) Total heat dissipated in any time interval is same from both frames
(D) Change in momentum of ball in any time interval is same from both frames.
5. A disc is given an angular speed w0 and released from a certain height (as shown in figure). Motion of
disc is observed after collision with the rough surface. Velocity of centre of mass of ball and direction of
w is shown in figure after the collision. Mark possible path, disc CAN follow after the collision.
Released from rest
w0
Rough Surface
v
v v v
w0
(A) (B) w (C) w=0 (D) w
6. A uniform solid square plate ABCD of mass m and side a is moving in x-y horizontal smooth plane. The
( )
velocity of centre of mass is v 0 2iˆ + 4ˆj m/s. The end A of square plate is suddenly fixed by a pin, find
the new velocity of centre of mass of square :
y vcm =v0 (2 ^i + 4 ^j )
B C
A D
x
(
(A) v 0 2iˆ + 4ˆj )
3v 0 ˆ 3v 0 ˆ
4
-i +
(B)
4
( ) 3v
4
3v
j (C) 0 ˆi - 0 ˆj
2
(D) 3v 0 ˆi - 3v 0 ˆj
7. In the figure shown, the mass of the disc as well as that of the trolley is M. The spring is ideal and has
stiffness k. The trolley can move horizontally on smooth floor and the disc can roll on the trolley surface
without slipping. The spring is compressed and the system released so that oscillations begin. The
(A) acceleration of centre of disc = twice of that of trolley
\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\
3m
A 1kg B
1kg
9
(D) Kinetic energy of system just after collision is mv2.
40
10. Two particles connected with massless rod are rotating with angular velocity w about axis as shown in
figure.
w w z
m m m y
q L q q L
O L x
O
L
m
(A) Total angular momentum about O in case (a) and (b) is 2m L2 sin2q w k̂ .
(B) Total angular momentum about O is 2m L2 sin2q w k̂ in case (a) only.
(C) Total angular momentum about O is 2m L2 sin2q w k̂ in case (b).
(D) In case (a) a horizontal torque must act to rotate system with constant w.
A
12. The acceleration of plank (ap) will be :
F F 4F 8F
(A) 3m + 8m (B) 4m + 8m (C) 3m + 8m (D) 3m + 8m
1 2 1 2 1 2 1 2
SECTION-III
Numerical Grid Type (Ranging from 0 to 9) 4 Q. [4 M (0)]
1. In the figure shown, a uniform solid cylinder A is initially rolling with velocity 14 m/s on the horizontal
surface of wedge B of identical mass. All surfaces are smooth and B has no initial velocity. Find maximum
height (in m) reached by cylinder. (g = 9.8 m/s2)
A B
2. A linear rod of mass m, length l is placed as shown in figure such that its one end rests on a rough table
of friction coefficient m. When string BS is cut, rod AB starts falling from rest. After rotating an angle
æ m ö
q = tan -1 ç ÷ , rod starts slipping on the table, find x?
è 2x ø
A B
M v
d
Pivot
v M
4. A spool, initially at rest, is kept on a frictionless incline making an angle q = 37° with the horizontal. The
mass of the spool is 2kg and it is pulled by a string as shown with a force of T = 10N. The string
connecting the spool and the pulley is initially horizontal. Find the initial acceleration of the spool on the
incline. Express your answer in m/s2.
m
r
R
q T
SECTION-IV
Matrix Match Type (4 × 5) 1 Q. [8 M (for each entry +2(0)]
1. In the arrangement shown here friction between the spool of mass m, moment of inertia I and the
plank of mass M is sufficient to prevent sliding and incline makes angle q with horizontal. There is no
slipping of rope. Assume that the system starts from rest rolling.
Column-I Column-II
(A) When m > M and there is no friction between the (P) Plank will ascend
plank’s and the inclined surface
(B) When M > m and there is no friction between the (Q) Plank will descend
plank’s and the inclined surface
(C) When m = M and there is no friction between the (R) Plank will remain stationary
plank’s and the inclined surface
(D) When m = M and friction coefficient between the (S) Spool may rotate clockwise
plank’s and the inclined surface is tan q
(T) Spool may rotate anticlockwise