Professional Documents
Culture Documents
2
Thank you for choosing this product. WEEE contains both polluting substances (which
We are proud to offer the ideal product for can cause negative consequences for the
EN
you and the best complete range of home environment) and basic components (which can
appliances for your daily routine. be re-used). It is important to have WEEE
subjected to specific treatments, in order to
remove and dispose properly all pollutants, and
Carefully read this manual for correct and
recover and recycle all materials. Individuals can
safe appliance use and for helpful tips on
play an important role in ensuring that WEEE
efficient maintenance.
does not become an environmental issue; it is
essential to follow some basic rules:
l WEEE should not be treated as household
waste;
Only use the washing machine after
carefully reading these instructions. We l WEEE should be handed over to the relevant
recommend you always keep this manual on collection points managed by the municipality or
hand and in good condition for any future by registered companies. In many countries, for
owners. large WEEE, home collection could be present.
In many countries, when you buy a new
appliance, the old one may be returned to the
FOR U.K. ONLY retailer who has to collect it free of charge on a
On receipt of your appliance please one-to-one basis, as long as the equipment is of
check it carefully for damage. Any equivalent type and has the same functions as
damage found must be reported the supplied equipment.
to the delivery driver immediately.
Alternatively damage found must be
reported to the retailer within 2 days of Contents
receipt.
1. GENERAL SAFETY RULES
2. INSTALLATION
Each product is identified by a unique 16-
character code, also called the “serial 3. DETERGENT DRAWER
number”, printed on the sticker. This can be 4. PRACTICAL HINTS
found inside the door opening. This code is
a unique code for your product that you will 5. CLEANING AND MAINTENANCE
need to register the product warranty, or if
you need to contact the Customer Service 6. PORTHOLE EMERGENCY OPENING
Centre. 7. REMOTE CONTROL (WI-FI)
8. QUICK USER GUIDE
Environmental conditions 9. CONTROLS AND PROGRAMS
3
1. GENERAL SAFETY in a safe way and understand the
RULES hazards involved.
Children shall not play with the
l This appliance is intended to appliance. Cleaning and user
be used in household and maintenance shall not be made
similar applications such as: by children without supervision.
- Staff kitchen areas in shops, offices
and other working environments; l Children should be supervised
- Farm houses; to ensure that they do not play
- By clients in hotels, motels and with the appliance.
other residential type environments;
- Bed and breakfast type environments. l Childrenof less than 3 years
A different use of this appliance should be kept away unless
from household environment continuously supervised.
or from typical housekeeping
functions, as commercial use by l If
the supply cord is damaged, it
expert or trained users, is excluded must be replaced by a special
even in the above applications. If cord or assembly available from
the appliance is used in a manner the manufacturer or its service
inconsistent with this it may reduce agent.
the life of the appliance and may
void the manufacturer’s warranty. l Only use the hose-sets
Any damage to the appliance or supplied with the appliance for
other damage or loss arising the water supply connection
through use that is not consistent (do not reuse old hose-sets).
with domestic or household use
(even if located in a domestic or l Waterpressure must be between
household environment) shall not 0.05 MPa and 0.8 MPa.
be accepted by the manufacturer to
l Make sure carpets or rugs do
the fullest extent permitted by law.
not obstruct the base or any of
l This appliance can be used by the ventilation openings.
children aged from 8 years and
above and persons with reduced l The final part of a washer dryer
physical, sensory or mental cycle occurs without heat (cool
capabilities or lack of experience down cycle) to ensure that the
and knowledge if they have been items are left at a temperature
given supervision or instruction that ensures that the items will
concerning use of the appliance not be damaged.
4
l Items such as foam rubber
WARNING: (latex foam), shower caps,
never stop a washer dryer before waterproof textiles, rubber
EN
the end of the drying cycle backed articles and clothes or
unless all items are quickly pillows fitted with foam rubber
removed and spread out so that pads should not be dried in the
the heat is dissipated. washer dryer.
5
l To consult the product technical l Do not pull on the power cord
specification please refer to the or appliance to unplug the
manufacturer website. machine.
6
2. INSTALLATION
l Remove the 2 or 4 transportation 1
EN
screws (A) on the back and
remove the 2 or 4 flat washers, A A
B
rubber bungs and plastic spacer B A
tubes (B) as illustrated in figure 1. A
B B
l If the washing machine is built-in,
unscrew the 3 or 4 transportation
screws (A) and remove the 3 or 4
flat washers, rubber bungs and
plastic spacer tubes (B).
l During the removal of the screws
occasionally spacer tubes fall
inside the product, these can be
remove by tilting the product forward
and recovering them from the floor or
inside the base of the machine.
l Cover the open transportation screw 2
holes with the 2 or 4 plastic caps
A
included in the instruction bag. 3
1 2
WARNING:
keep packaging materials
away from children.
l Place the corrugated plastic sheet, B
found on top of the appliance during
the unpacking process, into the base
of the appliance as shown in figure 2
(according to the model, consider
version A, B or C).
In some models this operation
will not be necessary, because C
the corrugated plastic sheet
will be already placed on the 3
bottom of the appliance. 2 1
7
Hydraulic connections 3
4
l HOT&COLD (fig. 4):
water mains connection settings with hot
and cold water for higher energy savings. 1
Connect the grey tube to the cold water
tap and the red one to the hot water
tap. The machine can be connected to
the cold water tap only: in this case, some
programs may start a few minutes later.
5
l AQUASTOP (fig. 5):
a device located on the supply tube that
stops water flow if the tube deteriorates; B
in this case, a red mark will appear in the
window “A” and the tube must be
replaced. To unscrew the nut, press the A
one-way lock device "B".
8
Setting 7
l The washing machine should be installed in
EN
its final position such that the water fill hose
is not kinked or trapped. The corrugated
drain hose should be inserted into suitable
drain pipe of between 50 cm and 85 cm
height above the floor using the curved drain
hose support. If an under sink connection is
used the drain hose must be routed above
the sink overfill opening to prevent back
siphoning. Care must be taken to avoid
min 4 cm
kinking or trapping the drain hose (fig. 7).
max 100 cm
l Level the appliance using the feet as
+2,6 mt
illustrated in figure 8:
max min 50 cm
a. turn the nut clockwise to release the max 85 cm
screw;
b. rotate the foot to raise or lower it until it * ACCESSORY SOLD SEPARATELY
touches to the floor;
c. lock the foot, screwing in the nut, until it 8
tightens against to the bottom of the
washing machine.
WARNING: B
contact the Customer Service Centre
should the power cord need
replacement.
Installation faults are not covered by
the manufacturers warranty.
C
9
3. DETERGENT DRAWER
The detergent draw is split into 3
compartments as illustrated in figure 9: 9
l compartment "1": for prewash detergent;
l compartment “ ”: for special additives, 1
softeners, starch fragrances, etc.;
2
WARNING:
only use liquid products; the washing
machine is set to automatically dose
additives at each cycle during the last
rinse.
10
4. PRACTICAL HINTS Maximise the load size
l Achieve the best use of energy, water,
Load tips detergent and time by using the
EN
recommended maximum load size.
When sorting laundry, make sure: Save up to 50% energy by washing a full
load instead of 2 half loads.
- have eliminated metallic objects such as
hair clips, pins, coins, from laundry;
Do you need to pre-wash?
- to have buttoned pillow cases, closed l For heavily soiled laundry only!
zips, tied loose belts and long robe SAVE detergent, time, water and
ribbons; between 5 to 15% energy consumption
- to have removed rollers, hooks or clips by NOT selecting Prewash for slight to
from curtains; normally soiled laundry.
11
The use of ecological detergents without
When washing heavily soiled whites, phosphates may cause the following
we recommend using cotton programs of effects:
60°C or above and a normal washing
powder (heavy duty) that contains
- cloudier rinse drain water: This effect is
bleaching agents that at medium/high
tied to the suspended zeolites which do
temperatures provide excellent results.
not have negative effects on rinse
efficiency.
For washes between 40°C and 60°C
the type of detergent used needs to be - white powder (zeolites) on laundry at
appropriate for the type of fabric and the end of the wash: this is normal, the
level of soiling. Normal powders are powder is not absorbed by fabric and does
suitable for “white” or colour fast fabrics not change its colour.
with high soiling, while liquid detergents To remove the zeolites, select a rinse
or “colour protecting” powders are programme. In the future consider using
suitable for coloured fabrics with light slightly less detergent.
levels of soiling.
- foam in the water at last rinse: this does
not necessary indicate poor rinsing.
For washing at temperatures below Consider using less detergent in future
40°C we recommend the use of liquid washes.
detergents or detergents specifically
labeled as suitable for low temperature
washing. - abundant foam: This is often due to the
anionic surfactants found in the detergents
which are hard to eliminate from laundry.
For washing wool or silk, only use In this case, do not re-rinse to eliminate
detergents specifically formulated for these effects: it will not help at all.
these fabrics. We suggest conducting a maintenance
wash using a proprietary cleaner.
l Too much detergent leads to excessive
foam, which prevents the cycle being If the problem persists or if you suspect a
carried out correctly. It could also affect malfunction, immediately contact an
the quality of the washing and rinsing. Authorised Customer Service Centre.
12
5. CLEANING AND l Fill the drawer with hot water.
MAINTENANCE
EN
Looking after your appliance correctly can
extend its lifespan.
Drawer cleaning
l Shake the drawer in order to let the water
l It is advisable to regularly clean the flow in all the compartments.
detergent drawer to avoid the
accumulation of detergent and additive
residues.
1 WARNING:
DO NOT use acid products (for example
vinegar) or aggressive detergents to
clean the drawer, in order to avoid
2 damaging the seals and/or internal
parts of the appliance.
13
Cleaning the pump filter S u g g e s tio n s fo r m o v e s o r
prolonged disuse
l The appliance has a special filter that
traps larger residues that could block the
draining system, such as buttons or coins l If the appliance is kept in a non-heated
(depending on the model, consider room for long periods of time, all water
version A or B). residues must be completely removed
We recommend checking and cleaning from the pipes.
the filter 5 or 6 times a year.
l Disconnect the machine from the power
l Disconnect the machine from the power supply socket.
supply.
l Ensure all the water has been emptied l Detach the tube from the drainage system
from the drum. and clip on the rear of the machine and
l Before unscrewing the filter, we lower it, fully draining water into a bowl.
recommend you place an absorbent cloth
under it to keep the floor dry. A small l Secure the drain tube with the drainage
amount of water will come out of the filter system and clip on the rear of the
as you remove it - this is normal. machine when finished.
l Turn the filter counter-clockwise to the
limit stop. l Keep the door glass and gasket clean.
l Remove and clean the filter; when
finished, replace it turning it clockwise. FOR MODELS WITH AUTOMATIC
The filter handle will be locked when it is LIQUID DETERGENT AND SOFTENER
not possible to turn any further and the DOSING SYSTEM:
handle is horizontal. Smearing a small should you need to tilt or move the
amount of liquid soap on the filter seal will machine, remove the detergent drawer
help refitting. before proceeding, keeping it
l Repeat the previous steps in reverse horizontal so as to avoid any leakage.
order to reassemble all parts.
14
6. PORTHOLE EMERGENCY OPENING
Should the porthole be locked due to power
EN
Shortage (if the plug is removed before the
end of the cycle, re-plug it and turn off the
machine to open the door) or as a result of
a fault, it can be opened according to the
following emergency unlocking procedure:
1. Disconnect the machine from the power
socket.
2. Ensure that the water level is below the
porthole before opening it, to prevent any
flooding. Otherwise, drain excess water
through the drain tube and collect it in a
bucket.
3. Tilt the machine (or increase the feet
height) and remove the visible screw in
the front bottom corner of the washing
machine (fig. 1).
4. Insert a screw driver or a similar tool in the
visible hook. Lever down and simultaneously
open the porthole as shown in figure 2.
5. Remember to re-assemble the screw at
the end of the process.
15
7. REMOTE CONTROL (WI-FI)
This appliance is equipped with Wi-Fi TO DISABLE REMOTE CONTROL
technology that allows you to control it
remotely via App. l To exit REMOTE CONTROL mode while
a cycle is underway, turn the programme
selector to any position other than
MACHINE ENROLLMENT (ON APP) REMOTE CONTROL (Wi-Fi). The control
l Download the App on your device by panel on the appliance will be operative
framing the following QR code: once again, and if the cycle is paused,
you will be able to open the door once the
DOOR LOCKED indicator light switches
off.
Get all the details of the Wi-Fi l With the door closed, turn the knob to the
functions by browsing the App in REMOTE CONTROL (Wi-Fi) position to
DEMO mode. control the appliance using the app once
again. If there is a cycle underway, it will
l Open the App, create the user profile continue.
(or log-in if it is already created previously)
and enroll the appliance following the
instructions on the device display.
16
8. QUICK USER GUIDE 9. CONTROLS AND
This appliance automatically adjusts the PROGRAMS
EN
level of the water to the type and quantity of
washing. This system gives a reduction in
energy consumption and a saving in
washing times.
Program selection
B C D H E F G A
l Turn on the appliance and select the
required program.
Technical data
Water pressure:
min 0.05 Mpa / max 0.8 Mpa
(0.05 MPa dispenses approximately 1 litre
of water in 10 seconds)
17
l Moreover, If you want to modify the
WARNING: chosen programme, press the desired
don’t touch the buttons while inserting options buttons, modify the default
the plug because the machines parameters and then press START/
calibrates the systems during the first PAUSE button to start the cycle.
seconds: touching the buttons, the
machine couldn’t work property. In Only the options compatible with the
this case, remove the plug and repeat set programme can be selected.
the operation.
l After switching on the appliance, wait a
few seconds for the programme to start
PROGRAMME selector with OFF running.
position PROGRAMME DURATION
l When the programme selector is turned l When a programme is selected the
the display lights up to show the settings display automatically shows the cycle
for the programme selected. duration, which can vary, depending on
the options selected.
l Switch off the washing machine by l Once the programme has started you will
turning the selector to OFF. be kept informed constantly of the time
remaining to the end of the wash.
First starting l The appliance calculates the time to the
end of the selected programme based
- Language setting upon a standard loading, during the cycle,
l After connecting the machine to the the appliance corrects the time to that
network and turning it on, press the "B" applicable to the size and composition of
or "C" button to display the available the load.
languages.
PROGRAMME END
l Select the desired language pressing the l When the display shows that the
START/PAUSE button. programme is finished and the DOOR
LOCKED indicator light has gone out, the
- Change the language
door can be opened.
If you want to change the setting language
you will have to press simultaneously "D" l At the end of the cycle, switch off the
and "E" buttons for about 5 seconds. appliance by turning the selector to OFF.
ENGLISH will appear on the display, and
you will be able to choose a new language. The programme selector must be
returned to the OFF position at the end
of each cycle or when starting a
START/PAUSE button subsequent wash cycle prior to the next
programme being selected and started.
Close the door BEFORE selecting the
button START/PAUSE.
PAUSING THE MACHINE
l To start the selected cycle with the preset l Keep the START/PAUSE button pressed
parameters, press START/PAUSE. When for about 2 seconds (some light indicators
the programme is running, the display will and the residual time display will flash,
show the time to elapse. showing that the machine is paused).
18
l To reactivate the spin cycle press the
For safety reasons, in some wash button until you reach the spin speed you
cycle phases, the door can be opened would like to set.
only if the level of the water is below
EN
its lower edge and if the temperature
l It is possible to modify the spin speed
is less than 45°C. If these conditions
without pausing the machine.
are met, wait for the DOOR LOCKED
light to switch off before opening the
door. An over dosing of detergent can
cause excessive foaming. If the
appliance detects the presence of
l Press the START/PAUSE button again to
excessive foam, it may exclude the
re-start the programme from the point it
spinning phase or extend the duration
had been paused at.
of the program and increase water
consumption.
CANCELLING THE SET PROGRAMME
l To cancel the programme, set the
selector to the OFF position. The machine is fitted with a special
electronic device, which prevents the
l Wait until the DOOR LOCKED light has
spin cycle should the load be
gone out before opening the door.
unbalanced. This reduces the noise
and vibration in the machine and so
TEMPERATURE SELECTION prolongs the life of your machine.
button
l This button allows you to change the
DELAY START button
temperature of the wash cycles.
l It is not possible to raise the temperature l This button allows you to pre-programme
over the maximum allowed for the the wash cycle to delay the start of the
programme, in order to protect the cycle for up to 24 hours.
fabrics.
l To delay the start use the following
l If you want carry out a cold wash all the procedure:
indicators must be off.
- Select the required programme.
19
If there is a break in the power supply l We recommend you use only 20% of the
whilst the machine is operating, when recommended quantities shown on the
the power is restored, the machine will detergent pack.
restart from the beginning of the phase it
was in when the power was lost.
- EXTRA RINSE
l This option allows you to add one rinse at
The option buttons should be selected
the end of the washing cycle and is useful
before pressing the START/PAUSE
for people with delicate and sensitive
button.
skin, for which a small amount of
detergent residue can cause irritations or
allergies.
RAPID / STAIN LEVEL button l It is advisable to also use this function for
the children clothes and for the washing
This button allows you to choose between of heavily soiled items, which requires a
two different options, depending on the lot of detergent to be used, or for the
selected programme. washing of toweling items whose fibres
mostly have the tendency to hold the
- RAPID detergent.
20
DRYING SELECTION button l ACTIVE WASH is designed for reduced
loads and lightly soiled garments, aiming
This button allows you: to limit the unnecessary waste.
EN
- Automatic washing/drying cycle - NIGHT & DAY
After the selection of washing programme
according to laundry type, select a degree l This option reduces the intermediate spin
of dryness by pressing this button. At the speed to 400 rpm, where applicable,
end of the washing programme, the increase the water level during rinsing
selected drying cycle will start automatically. and keep the laundry immersed in water
after the final rinse, in order to spread the
If a washing programme is not compatible fiber perfectly.
with automatic drying is selected, this
function will not be activated. l During the drum water retention phase,
the machine is in pause mode.
If you exceed the maximum dryable load
of laundry indicated in the programme l Press START to end the cycle with the
table, the laundry may not be dried spin (which can be reduced or removed
satisfactory. with the specific button) and drain phase.
l "End" will appear in the display at the l Do not start the programme with laundry
end of the programme and the DOOR in the washing machine.
LOCKED light will go off, it is now
possible to open the door.
l It is suggested that this is carried out after
every 50 washing cycles.
SPECIAL PROGRAMMES button
l The option can only be selected for the
This button allows you to choose between DRAIN & SPIN programme.
three different options (available for some
programmes only):
These options must be selected
- ACTIVE WASH before pressing the START/PAUSE
button.
l This option (which can be set in several If an option is selected that is not
programs) optimizes the water and compatible with the selected
energy consumption of the selected programme then the option indicator
program, maintaining the washing light first flashes and then goes off.
performance unchanged.
21
CHILD LOCK l A special safety device prevents the door
from being opened immediately after the
l Pressing simultaneously the buttons "B" end of the cycle. Wait for 2 minutes after
and "C" for about 3 seconds, the the wash cycle has finished and the
machine allows you to lock the keys. In DOOR LOCKED light has gone out before
this way, you can avoid making accidental or opening the door. At the end of the cycle
unwanted changes if a button on the turn the programme selector to OFF.
display is pressed accidently during a cycle.
2) KEY LOCK INDICATOR LIGHT
l The key lock can be simply cancelled by
pressing the two buttons simultaneously The indicator light show that the keys are
again or turning off the appliance. locked.
1) DOOR LOCKED INDICATOR LIGHT - determines the length of the wash cycle;
l The indicator light is illuminated when the
- controls rinsing according to the type of
door is fully closed.
fabric selected to be washed it;
Close the door BEFORE selecting the - adjusts the rhythm of drum rotation for
START/PAUSE button. the type of fabric being washed;
22
- SLOW FLASHING: remote control 7) SPIN SPEED INDICATOR LIGHTS
disabled. This show the spin speed of the selected
programme, you can reduce or omit by the
EN
- QUICK FLASHING FOR 3 SECONDS, relevant button.
THEN OFF: the machine cannot connect
to the home Wi-Fi network or has not yet 8) OPTIONS INDICATOR LIGHTS
been enrolled on the App.
The indicator lights show the options that
can be selected by the relevant button.
- SLOW BLINKING FOR 3 TIMES, THEN
OFF FOR 2 SECONDS: reset of the Wi-Fi 9) DRYING SELECTION INDICATOR LIGHTS
network (during enrollment on the App).
The indicators display the degrees of dryness
that can be selected by the relevant button:
- ON FOR 1 SECOND, THEN OFF FOR 3
SECONDS: the door is open. Remote Automatic drying programmes
control cannot be activated. EXTRA DRY
(suitable for towels, bathrobes and
5) STAIN LEVEL INDICATOR LIGHT bulky loads).
IRON DRY
The indicator light shows the selection of
(that leaves the laundry ready for
the relevant option.
ironing).
CUPBOARD DRY
6) WASH TEMPERATURE INDICATOR (for items that will be put away
LIGHTS without ironing).
This show the washing temperature of the
selected programme that can be changed 10) SPECIAL PROGRAMMES INDICATOR
(where allowed) by the relevant button. LIGHTS
If you want carry out a cold wash all the The indicator lights show the options that
indicators must be off. can be selected by the relevant button.
23
Table of programmes
1)
(MAX.) * 1
2
PROGRAMME (see control panel)
(MAX.) 2 1
5) 2)
COTTON
4)
8 9 9 10 11 12 13 14 90° ( )
ECO 5) 2)
40 60
ECO 40-60** 8 9 9 10 11 12 13 14 60°
WASH AND DRY
ECO 5 5 6 6 8 8 8 9 -
40 60 (ECO 40-60 + )
5) WOOL & HAND
WASH
2 2 2 2 2 2,5 2,5 2,5 30°
5) 2)
20°C
20°C
4)
8 9 9 10 11 12 13 14 20°
5) SYNTHETIC 2)
AND COLOURED 4)
4 4,5 4,5 5 5,5 6 6,5 7 60° ( )
RINSE - - - - - - - - -
4)
SOFT CARE 2,5 2,5 2,5 2,5 3 3 3,5 3,5 40°
5)
14' 1,5 1,5 1,5 1,5 1,5 2 2 2 30°
3)
14'/30'/44'
RAPID CARE 30' 2,5 2,5 2,5 2,5 2,5 3 3 3 30°
TOTAL
CARE TOTAL CARE 4 4,5 4,5 5 5,5 6 6,5 7 30°
DRY WOOL 1 1 1 1 1 1 1 1 -
DRYING
HIGH HEAT 5 5 6 6 8 8 8 9 -
24
Please read these notes:
INFORMATION FOR THE TEST
* Maximum load capacity of dry clothes,
EN
LABORATORIES
according to the model used (see control
panel).
STANDARD PROGRAMMES
(Only for models with liquid ACCORDING TO
detergent compartment) Directive 96/60/CE
When only a limited number of
WASHING:
articles have stains which require
treatment with liquid bleaching ECO 40-60 PROGRAMME
agents, preliminary removal of SETTING THE TEMPERATURE TO
stain can be carried out in the 60°C
washing machine.
DRYING:
Pour the bleach into the liquid
DRYING PROGRAMME
bleach container, inserted into the
compartment marked "2" in the HIGH HEAT (COTTON)
detergent drawer, and set the DEGREE OF DRYNESS
special programme RINSE. CUPBOARD DRY
When this phase has terminated, _______________________________________
switch off the appliance, add the
rest of the fabrics and proceed STANDARD PROGRAMMES
ACCORDING TO
with a normal wash on the most
(EU) No 2019/2023
suitable programme.
( ) Only with PREWASH option selected WASHING:
(programmes with PREWASH option ECO 40-60 PROGRAMME
available).
WASH AND DRY:
1) When a programme is selected, ECO 40-60 PROGRAMME +
on the display is shown the DEGREE OF DRYNESS
display shows the recommended CUPBOARD DRY
wash temperature that can be
reduced (where allowed) by the
relevant button.
25
Description of programmes to assess the compliance with the EU
Ecodesign legislation (environmentally
To clean different types of fabrics and friendly products design).
various levels of dirt, the washing machine
WASH AND DRY (ECO 40-60 + )
has specific programs to meet every need
The WASH AND DRY cycle is able to clean
of washing (see table of programmes).
normally soiled cotton laundry declared to
be washable at 40°C or 60°C, together in
Choose programme in accordance the same cycle, and to dry it in such a way
with the laundry instructions appearing that it can be immediately stored in a cupboard.
on labels, especially the maximum This programme is used to assess the
recommended temperature. compliance with the EU Ecodesign legislation
(environmentally friendly products design).
26
SOFT CARE DRY WOOL
Developed to take good care of delicate Low temperature drying programme, ideal
items, this programme washes at a low to dry woollen clothes with maximum care
EN
temperature in 59 minutes. An extended, in- and softness, reducing rubbing of fabrics
depth rinse nourishes fabric fibres. related to the amount of the washing and
the spin speed selected for the wash.
RAPID CARE 14'-30'-44' The cycle is suitable for small loads up to
Saving without compromising! This new 1 kg (3 sweaters).
programme may be used to obtain excellent
results while saving water, energy, detergent
and time. This option washes at a medium
temperature suitable for any kind of fabric.
Recommended for small loads and lightly
soiled items. The wool drying cycle of this
machine has been approved by "The
ALL IN ONE 59'. Woolmark Company" for the drying
This programme allows you to wash of machine washable wool products
different fabrics together such as cottons, provided that the products are
synthetics and mixed fabrics in only 59 washed and dried according to the
minutes, using the full load of the washing instructions on the garment label and
machine, at 40°C (or less) temperature. those issues by the manufacturer of
This programme is particularly suited to this machine.
slightly dirty fabrics.
The Woolmark symbol is a
Certification mark in many countries.
TOTAL CARE
M1715
This new programme may be used to wash
laundry of different colourfast colours and
fabrics together without altering their LOW HEAT
original look and feel. New POWER CARE Low temperature drying programme
technology uses a perfect emulsion of water recommended for synthetics and mixed
and detergent to take the best possible care fibres (always refer to the laundry care label).
of your clothes, with optimal washing
performance at a temperature of 30°C. HIGH HEAT
High temperature drying programme
recommended for cottons and linen items
DRYING
(always refer to the laundry care label).
WARNING:
Dispensers used for concentrated
powders and liquid detergents must
be removed from the drum before
commencing the tumble drying
programmes.
27
10. DRYING CYCLE The correct way to dry
l Drying guidance advice is general, but
practical experience of using the product l Open the door.
will help you to achieve the best drying
results. l Fill with the laundry, not exceeding the
maximum drying load indicated in the
l We recommend setting a lower drying programme table. For large items (e.g.
time than indicated, when first using the sheets) or very absorbent items (e.g.
appliance in order to establish the degree towels or jeans), it is a good idea to
of dryness required. reduce the load.
CUPBOARD DRY
DO NOT tumble dry.
(for items that will be put away without
ironing).
If the fabric does not have a care label,
you should assume that it is not TIMED DRYING PROGRAMS
suitable for drying. - 120 MINUTES
- 90 MINUTES
- 60 MINUTES
- By size and thickness - 30 MINUTES
Whenever the wash load is bigger than
the drying capacity, separate the clothes
according to thickness (e.g. towels from By selecting the wool drying
thin underwear). programme, it's not possible to select
a degree of dryness different from the
- By fabric type default one.
Cottons/linen: towels, cotton jersey, bed
and table linen.
Synthetics: blouses, shirts, overalls, etc. l The washer dryer will calculate the time
made of polyester or polyamide, as well needed for drying and the level of
as for cotton/synthetic mixes. moisture remaining in the laundry,
according to the load and drying type
l Only dry pre-spun laundry. selected.
28
l Check that the tap is turned on and that
During the drying phase the drum will
the discharge hose is positioned
accelerate to a higher speed to
correctly.
distribute the load and to optimize the
EN
drying performance.
29
11. TROUBLESHOOTING AND WARRANTY
If you believe the washing machine is not working correctly, consult the quick guide
provided below which includes some practical tips on how to fix the most common
problems.
l Models with a display: the error is shown by a number preceded by the letter “E”
(example: E2 = Error 2).
l Models without display: an error is shown by a sequence of flashes of every LED.
The error code is shown by the number of flashes followed by a pause of 5 seconds
(example: two flashes – pause 5 seconds – two flashes – repeating = Error 2).
30
OTHER ANOMALIES
EN
The washing machine Make sure the product is plugged into a working supply socket.
does not work / start Make sure power is on.
Make sure the wall socket is working, testing it with another
appliance such as a lamp.
The door may not be correctly closed: open and close it again.
Check whether the required program was correctly selected and the
start button pressed.
Make sure the washing machine is not in pause or time delay mode.
Water leaked on the This may be due to a leak from the seal between the tap, supply
floor near the hose and fill valve; in this case, replace it and tighten the hose
washing machine connections correctly.
Make sure the front filter is correctly closed.
The washing machine The machine is fitted with a detection system that protects the load
does not spin and product from damage if the load is not balanced before spinning.
This may result in:-
• The machine attempts to balance the load, increasing the time of
spin.
• Reduction of the speed of spin to decrease vibrations and noise.
• The spin cycle aborting to protect the machine and load.
If this is experienced remove the load de-tangle it, reload it and
restart the spin program.
This could be due to the fact that water has not been completely
drained: wait a few minutes. If the problem persists, see Error 3
section.
Some models include a "no spin" function: make sure it is not
selected.
Check which options are selected and their effect on the spin cycle.
Excessive detergent can impede the spin cycle, ensure the correct
amount of detergent is being used.
Strong vibrations / The washing machine may not be fully levelled: if necessary, adjust
noises are heard the feet as indicated in the specific section.
during the spin cycle Make sure transport screws, rubber bungs and spacer tubes were
removed.
Make sure there are no foreign objects inside the drum (coins,
hinges, buttons, etc…).
31
It is always recommended to use original
spare parts, that are available at our By placing the mark on this
Authorised Customer Service Centres. product, we are confirming compliance
to all relevant European safety, health
and environmental requirements which
Warranty are applicable in legislation for this
The product is guaranteed under the product.
terms and conditions stated on the
certificate included with the product. The
certificate has to be stored so as to be
shown to the Authorized Customer
Service Centre in case of need. You can The manufacturer declines all
also check the warranty conditions on responsibility for any printing errors in
our web site. To obtain assistance, the booklet included with this product.
please fill in the form on-line or contact Moreover, it also reserves the right to
us at the number indicated on the make any changes deemed useful to its
support page of our web site. products without changing their
essential characteristics.
32
fkhldsk
fkhldsk
fkhldsk
- HD -
20.06 - 43034951.B - IDM s.r.l.