Professional Documents
Culture Documents
BTM8615
Bluetooth Module Data Sheet
Reproduction of this document, in part of in whole, by any means is prohibited without written permission
from Buddies Technology Limited. The information contained herein is believed to be accurate as of
the date of publication. However, Buddies Tech is not liable for any damages, including indirect or
consequential from the use of software this document represents, or any reliance of the accuracy of
this document. Buddies Tech reserves the right to change the contents of this document at any time
without notice.
This document contains proprietary confidential trade secrets and may be subject to additional
restrictions contained in the licensing agreement under which this document was obtained.
1
http://www.buddies-tech.com BTM8615 DATASHEET
Revision History
2
http://www.buddies-tech.com BTM8615 DATASHEET
CONTENT
1. INTRODUCTION................................................................................................................................. 4
3. PHYSICAL CHARACTERISTIC....................................................................................................... 6
3
http://www.buddies-tech.com BTM8615 DATASHEET
1. INTRODUCTION
The BTM8615 Bluetooth® module is a perfect solution for enhanced audio applications,
such as mono headphone and speaker. It can be connected with any Bluetooth®
devices in an operating range. It is slim and light so the designers can have better
flexibilities for the product shapes.
The BTM8615 Bluetooth® module complies with Bluetooth® specification version 4.0. It
supports HSP, HFP, A2DP, AVRCP profiles. It integrates RF Baseband controller,
antenna,… etc. and provide UART interface, programmable I/O, stereo speaker output,
microphone input,… etc.
Antenna PIOs
Filter
MIC USB Audio
SPI
CSR8615 Speaker
UART
Line-in
4
http://www.buddies-tech.com BTM8615 DATASHEET
1.2 Features
Bluetooth® V4.0
Class 2 support
Support SMSC-T
RoHS Compliant
1.3 Application
Bluetooth Speaker
5
http://www.buddies-tech.com BTM8615 DATASHEET
Bluetooth Specification
Chip Set CSR 8615 (ROM)
Module ID BTM8615
BT Standard Bluetooth® V4.0
RF TX Output Power 4dBm (Class II)
Sensitivity -86dBm@0.1%BER
6
3. PHYSICAL CHARACTERISTIC
Pin Definition
7
http://www.buddies-tech.com BTM8615 DATASHEET
7 NC NC NC
8 NC NC NC
9 NC NC NC
10 NC NC NC
11 NC NC NC
8
http://www.buddies-tech.com BTM8615 DATASHEET
21 GND Ground
Ground
9
http://www.buddies-tech.com BTM8615 DATASHEET
48 NC NC NC
51 NC NC NC
52 NC NC NC
55 NC NC NC
59 RF RF RF out
10
1 2 3 4
ANT
单单单单单单单单单单
16 欧欧-32 欧欧
C1 NC Line IN
SPI调调调调
LINE/MIC_AN
LINE/MIC_AP
L1
SPKR_LN
D D
SPKR_LP
0R R14
AGND
LINE/MIC_AP 1K J2
C2 NC SPI_MOSI L_IN
TP1 MOSI
R15 1K
SPI_CLK R_IN
U1 TP2 CLK
BTM8615 R16 2K2
60
59
58
57
56
55
54
53
52
51
50
49
GND
SPK R_LN
RF
SPK R_LP
LINE/MIC_AP
AGND
NC
NC
NC
LINE/MIC_AN
NC
SPI_EN LINE/MIC_AN
TP5 SPI_EN
1 48
GND GND NC
2 47
AIO_0 AIO_0 GND GND
3 46
UART_TX LED_2 LED_2
45
4 PIO_18 PIO_18
UART_RX
5 44
UART_RTS PIO_21 PIO_21
6 43
PIO_6 PIO_6
UART_CTS
7 42
NC PIO_7 PIO_7 MIC
8 41 MIC_A
NC PIO_8 L2
LINE/MIC_AN C7
9 40 100nF 15nH
C NC PIO_1 C
39 -42dB
10 PIO_0 C9
NC
11 38 15PF
NC PIO_9 R11
37 2K2
12 GND
SPI_EN SPI_EN GND
13 36
GND GND USB_P R12
USB_P LINE/MIC_AP C8 MIC_BIAS
14 35 100nF
SPI_MISO USB_N 1K
SPI_MISO USB_N C10
15 34
SPI_MOSI GND
SPI_MOSI GND 2.2uF
16 33
SPI_CLK +3V3_OUT
SPI_CLK
17 32
VDD_PADS
VBAT_SENSE
18 +1V8_OUT C5
GND
BT_Reset
GND
LED_0
LED_1
VBAT
VBUS
GND
GND
PWR
GND
GND
100nF
30
29
28
27
26
25
24
23
21
22
20
19
VBAT
KEY&LED
C13
+1V8
B B
BT_Reset
2u2 C3 C4 BAT
LED_1
LED_0
4. REFERENCE SCHEMATIC
3.3V-4.2V VOL+
GND
GND
PWR
GND
GND
SW2 R1 10K PIO_6
2u2 100nF
+5V
VOL-
SW3 R2 10K PIO_7
FORWARD
SW4 R3 10K PIO_18
BACKWARD
SW5 R4 10K PIO_21
USB charger BT_Reset Reset Temperature sensor VBAT
1V8
PWR ON/OFF/PAIR
SW1 R5 10K PWR
7
5V
Q1
R10
GND
1 9K1 TH1
VCC USB_P C6 1uF Q2 LED1 RED R6 470R LED_0
J1 2 3904 AIO_0 10K FDV303N
D- 3 USB_N
D
D+
S
4
GND
MICRO-USB ID R10 R9
5
GND LED2 BLUE R7 470R
G
150K 100K C11 LED_1
100nF
PIO_0
6
A A
LED3 BLUE R8 470R LED_2
+5V
1 2 3 4
http://www.buddies-tech.com BTM8615 DATASHEET
5. PHYSICAL INTERFACE
5.6 Reset
The module is reset from several sources:
Reset# pin
Power on reset
Software configured watch-dog
The Reset pin is an active low reset and is internally filtered using the internal low
frequency clock oscillator. Recommended the low period >10ms.
RAM data not available after cold reset.
12
http://www.buddies-tech.com BTM8615 DATASHEET
5.7 RF Interface
The module integrates a balun filter. A 50ohms load is needed.
5.8 Batter charger
5.8.1 battery charger hardware operating modes
The battery charger hardware is controlled by VM ,it has 5 modes:
Disabled
Trickle charger
Fast charger
Standby: fully charged or float charge
Error: charging input voltage, VCHG is too low.
5.8.2 External charge mode
The external mode is for charging higher capacity batteries using an external bass
device. The current is controlled by sinking a varying current into the CHG_EXT pin, and the
current is determined by measuring the voltage drop across a resistor. The max current up to
700mA.
5.9.1 UART
This is a standard UART interface for communicating with other serial devices. The UART
interface provides a simple mechanism for communicating with other serial devices using
the RS232 protocol.
When the module is connected to another digital device, UART_RX and UART_TX
13
http://www.buddies-tech.com BTM8615 DATASHEET
transfer data between the two devices. The remaining two signals, UART_CTS and
UART_RTS, can be used to implement RS232 hardware flow control where both are
active low indicators.
Note: The serial port interface(UART)can be used for system debugging. Don’t
support to use command set for profile function application by UART, such as
HFP/A2DP/AVRCP and so on. These profiles function application can be controlled
only by PIO, such as pairing/connect/answer/play/pause/next/previous function
application and so on.
5.9.2 SPI
The synchronous serial port interface (SPI) can be used for system debugging. It can also be
used for in-system programming for the flash memory within the module. SPI interface
uses the SPI_MOSI, SPI_MISO, SPI_CSB and SPI_CLK pins. Testing points for the SPI
interface are reserved on board in case that the firmware shall be updated during
manufacture.
The module operates as a slave and thus SPI_MISO is an output of the module.
SPI_MISO is not in high-impedance state when SPI_CSB is pulled high. Instead, the
module outputs 0 if the processor is running and 1 if it is stopped. Thus the module
should NOT be connected in a multi-slave arrangement by simple parallel connection
of slave SPI_MISO lines.
14
http://www.buddies-tech.com BTM8615 DATASHEET
6.ELECTRICAL CHARACTERISTIC
Supply Voltage
Supply Voltage
15
http://www.buddies-tech.com BTM8615 DATASHEET
LED[0:2] 0 0 V
Current with 3.3V Input and Tristate Min Typ Max Unit
charge mode
charge mode
16
http://www.buddies-tech.com BTM8615 DATASHEET
6.6 RF characteristics
Bluetooth Bluetooth Unit
17
http://www.buddies-tech.com BTM8615 DATASHEET
7. PACKAGING INFORMATION
2. Assembly
3. Dimension
All rights are strictly reserved. Any portion of this paper shall not be reproduced, copied, or
translated to any other forms without permission from Buddies Technology Limited.
18