Professional Documents
Culture Documents
NE - 1 - Quick Installation Script
NE - 1 - Quick Installation Script
AED Training
Product Introduction
Overview
Description
The NETSCOUT Arbor Edge Defense (AED) platform is a single, stand-alone device that is easy to
install. In this lab exercise you will perform the quick installation script of an AED assigned to you.
Objectives
Install AED by completing the tasks of the quick start installation script.
Lab Topology
Please ensure you read each step carefully before performing the required task in the order described.
If you are asked for your [POD] number in this lab, use the number that is part of your NE
username.
In this exercise you will complete the quick installation script for the NETSCOUT AED assigned to you, steps
that are typically performed on new AED appliance and virtual machine (VM) platforms after power on.
Important: The quick installation script prompts you to enter values for settings that are required to install
your AED. To respond enter the values provided in each lab step to their corresponding setting. To accept
the default value for a setting just press ‘Enter’, the value in [...] will be applied to that setting. For example, a
https://portal.ne.netscout.com/dashboard/lab_guide/437/45085/ 1/6
14/9/22, 17:53 NE | 1 - Quick Installation Script
setting with the value of [none], pressing enter will apply no value to that setting and the quick installation
script will continue to the next setting.
Also note that when using your browser with the quick installation script, it is recomended that you use your
browser's menu options to paste values into the settings on the CLI page. To use the paste options in your
browser's menu, select from your browser’s File menu, or the the three dot vertical ellipsis or the three line
hamburger menu button, then select Edit > Paste. This process provides the most reliable method to paste
setting values into the CLI page.
1. From your NETSCOUT Experience user dashboard, click on the“Serial Console” link, this will open a new
tab that you will use to connect to the serial console of your AED.
Important: Check your browser's pop-up blocker settings if the new tab does not open.
Username: NE102
Password: Kinemumo4^
IMPORTANT: DO NOT TYPE ANYTHING DURING THIS STARTUP until you are prompted, doing so
may cause the data to be cached and may affect the remainder of the install.
Also, first read Steps 3 through 5 prior to performing these three steps. Both Steps 3 and 4 are closely
associated and specific to just this lab environment, and Step 5 happends quickly after the power on of
your AED. You would not need to perform these steps in this manner when installing your own AED.
3. These next steps need to be in sync with your instructor, read each both before proceeding. To
connect to your AED's serial console:
In the Appliance prompt type in AED but DO NOT PRESS ENTER YET
Ask your instructor to power on your AED VM and wait for confirmation...
If you do not see any text output after 30-45 seconds, notify your instructor.
4. At the GRUB menu, the system should boot automatically from “disk, (serial console)”. Optionally, you
may (re)install from CD, (serial console), but the boot procedures will be slightly different, you would
need to skip to Step 7 below if (re)install from DC, (serial console) selected.
Important: If you see a blank screen for more than 2-3 mins, the system may have completed it’s boot
and the serial console may be waiting for your user input, if you suspect that this may be the situation
for you, then press Enter to display the prompt again.
“Do you want to begin the install process? This will remove all current data and configuration
[n/y]”, type y and press Enter to proceed.
The installation initializes the system, installs the software, and builds the databases. These steps may
take some time to complete.
6. Wait while the AED installation process prepares the hard drives and installs necessary software
packages.
REMINDER: DO NOT TYPE ANYTHING DURING THE INSTALL until prompted. Doing so may cause the
data to be cached and may affect the remainder of the install.
Though it is a best practice to update the default admin password during this step, for this lab you will
update the admin password in a later step for this lab exercise.
Note: This IP must be set correctly to avoid duplicate IPs, and also to access this AED via the web.
12. Skip the configuration of mgt1 interface by accepting the default setting of [none] and press
Enter when prompted.
For this installation we will only use the mgt0 interface for access and management.
14. To allow HTTPS access to this appliance, when prompted https access from which
network? enter: 0.0.0.0/0
WARNING: In normal usage, 0.0.0.0/0 allows any device to access the AED console, there are no
access restrictions. Typically your company’s accepted network ranges would be defined to only allow
access from a small number of hosts or networks.
If needed in your network, you may choose to enter more than one network to allow access, for this
lab we are finished and do not need to add any other address.
Next, select the default [done] option by pressing Enter, this ends adding more HTTPS access.
15. To allow ping access, when prompted ping access from which network? enter: 0.0.0.0/0
When prompted again confirm no more entries by pressing Enter to accept the default [done] option.
16. We will not be setting cloudsignal access, press Enter to skip this step.
17. To allow SSH access, when prompted ssh access from which network? enter: 0.0.0.0/0
When prompted again confirm no more entries by pressing Enter to accept the default [done] option.
18. To configure DNS, when prompted DNS server IP address enter: 10.2.24.46
Continue to the next setting by pressing Enter, this completes adding the DNS server IP
19. To accept the current time and date, press Enter. The current date/time matches actual clock in UTC
and the format is:
MMDDhhmm[[CC]YY][.ss]
hh = Hour
mm = Minutes
ss: Seconds
20. To keep the clock in sync with all other devices, when prompted NTP server IP
address enter: 10.2.24.46
Note: You may receive an error message as the system attempts to synchronize the time with the
server. If this occurs, please proceed.
21. The system now reboots automatically, wait patiently until you are presented with the login prompt. It
may take two-to-four minutes for the lab-based vAED to reboot.
https://portal.ne.netscout.com/dashboard/lab_guide/437/45085/ 3/6
14/9/22, 17:53 NE | 1 - Quick Installation Script
Optional: Enter any observations or notes that you want to record about the quick installation script,
this is only for your reference later (click and drag the lower right corner to expand the box):
23. When prompted to login use the default admin user account credentials of:
Username: admin
Password: arbor
24. Next let’s change the default admin password, enter the following text on the command line (use
copy-and-paste as described previously):
25. Start the SSH server on the AED for remote access purposes, enter:
Note: The AED may alert by indicating that “No License Set”, at this time this message is ok, you will
add the license at a later time.
/ config write
Optional: Enter any observations or notes that you want to record, this is for your reference later:
30. Verifying AED Installation Status - To verify your installation, from your NETSCOUT Experience user
dashboard, click on the AED “Open Link”. A new tab opens that connects you to the AED Web-based
User Interface (UI).
31. If the installation was successful you should see the AED login prompt and you should be able to login
with the admin credentials you updated previously. If needed, you may skip the next step.
Username: admin
Password: Welcome123!
32. If you see an "Important Updates" window after you logged into the UI, just click the Accept button in
the pop-up.
https://portal.ne.netscout.com/dashboard/lab_guide/437/45085/ 4/6
14/9/22, 17:53 NE | 1 - Quick Installation Script
33. If you are unable to connect, go to the CLI connection via NETSCOUT Experience and review all of
your configuration settings!
Use the commands below to verify each setting, to view additional options for any command below,
use “?”
Examples:
/ ?
/ ip ?
/ ip interfaces ?
Optional: Enter any final observations or notes you want to record here, this is only for your reference
later:
/ ip route show
/ ip access show
/ ip access commit
/ config write
Check Solution
/ exit
37. Please notify the instructor that you have completed this lab exercise.
https://portal.ne.netscout.com/dashboard/lab_guide/437/45085/ 5/6
14/9/22, 17:53 NE | 1 - Quick Installation Script
If you would like a copy of this lab select either the Print or the Save Page As (Control-S) menu
options from your browser’s dropdown menu.
Depending on which browser you are using, to access these menu options select either:
Select "File" from the your browser's menu, then choose either:
Or select the three line hamburger menu button, then choose either:
This completes the lab exercise for the quick installation script for your AED. For more information about the
configuration settings for your AED's installation, refer to the AED Quick Start Card / Installation
Guide and/or the Arbor Edge Defense User Guide.
Version 6.8.0.0.2203.11 EN
https://portal.ne.netscout.com/dashboard/lab_guide/437/45085/ 6/6