Professional Documents
Culture Documents
Wind Turbine
Wind Turbine
3. WIND ENERGY:
3.1. Wind Data and Energy Estimation;
3.2. Types of Wind Energy Systems;
3.3. Performance; Site Selection;
3.4. Details of Wind Turbine Generator;
3.5. Safety and Environmental Aspects.
एक िनि�त �ेत्र में उपलब्ध पवन ऊजार् क� मात्रा क� गणना के िलए एक सक ं े त पवन घनत्व (डब्ल्यपू ीडी) है |इसको यह मल्ू यांकन
करने के िलए कायर्रत िकया जाता है िक िविभन्न स्थान पवन ऊजार् िकतनी अच्छी तरह उत्पन्न करते हैं । यह एक हवा के प्रवाह क�
िदशा के लंबवत सतह के माध्यम से इकाई समय में इकाई �ेत्र के माध्यम से बहने वाली पवन ऊजार् क� मात्रा का वणर्न करता है | इसे
वाट/वगर् में व्य� िकया जाता है । मीटर (W/m2) में व्य� िकया जाता है | पवन टबार्इनों के िलए आदशर् स्थानों क� तुलना करना और
चनु ाव के िलए इसका उपयोग िकया जाता है । आमतौर पर उच्च WPD के साथ स्थानों पर स्थािपत टबार्इन अिधक िवद्यतु ऊजार् का
उत्पादन करते है । िचत्र में प्रदिशर्त पवन ऊजार् मानिचत्र 50 मीटर क� ऊंचाई पर हवा के घनत्व को दशार्ता है | भारत में िविभन्न स्थानों
मानिचत्र में WPD को (i) 0-100 W/m2, (ii) 200 W/m2 से कम, (iii) 200-250 W/m2, (iv) 250-300 W/m2, (v) 300-
400 W/m2, और (vi) 400-500 W/m2 के �प में वग�कृ त िकया गया है । अिधकांश राज्यों में भारत में िबजली घनत्व 0-100
W/m2 क� सीमा में है । गजु रात और तिमल नाडु में कुछ स्थान में 250-300 W/m2 क� सीमा में WPD का कुछ अिधक मान के है ।
An indication for calculating the amount of wind power available at a certain area is the wind power density
(WPD). It is employed to evaluate how well various locations generate wind energy. It describes the amount
of wind energy flowing through unit area in unit time through a surface perpendicular to the direction of wind
1
WIND TURBINE
flow. It is expressed in Watt/sq. meter(W/m2). It assists in comparing and choosing the ideal locations for wind
turbines. Turbines installed at locations with higher WPD typically produce more electrical energy. The wind
power map displayed in Fig. 3.5 illustrates the density of wind at a height of 50 meters for various places in
India. In the map WPD, is classified as (i) 0-100 W/m2, (ii) less than 200 W/m2, (iii) 200-250 W/m2, (iv) 250-
300 W/m2, (v) 300-400 W/m2, and (vi) 400-500 W/m2. Most of the states in India have the power density in
the range of 0-100 W/m2. Few of the locations in Gujarat and Tamil Nadu have some higher value of WPD in
2
the range of 250-300 W/m .
According to the orientation of the rotor shaft with ground, small wind turbines can be classified as:
(1) Horizontal axis wind turbine (HAWT)
(2) Vertical axis wind turbine (VAWT)
2
WIND TURBINE
Horizontal axis wind turbine (HAWT) rotates on horizontal axis and vertical axis wind turbine (VAWT)
rotates on vertical axis. Both type of these wind turbine has its merits and demerits. Horizontal axis wind
turbine produces more electricity as compared with vertical axis wind turbine for a given amount of wind. The
view of HAWT and VAWT is shown in Fig. 4.2.
Horizontal axis wind turbine (HAWT) may be one blade, two blades, three blades turbine based on the
number of blades used in the turbine. They may be upwind or downwind depending on the orientation of
blades towards the wind. Vertical axis wind turbine (VAWT) may be Savnious type, darrieus type as shown
below.
3
WIND TURBINE
1. उच्च वािषर्क औसत हवा क� गित High annual average wind speed::
पवन चक्क� द्वारा उत्पन्न गित , हवा के वेग के घन मान पर िनभर्र करती है , हवा के वेग में छोटी सी वृिद्ध , शि� को स्प� �प से
प्रभािवत करती है। उदाहरण के िलए, वेग को दोगनु ा करने से शि� 8 गनु ा बढ़ जाती है। WECS के िलए उच्च वायु वेग के साथ एक
साइट का चयन करना स्प� �प से वांछनीय है । The speed generated by the wind mill depends on cubic values of
velocity of wind, the small increases in velocity markedly affect the power in the wind. For example,
Doubling the velocity, increases power by a factor of 8. It is obviously desirable to select a site for WECS
with high wind velocity.
2. एनीमेट्री डेटा क� उपलब्धता Availability of anemometry data:
यह एक और स्थान के चयन का सधु ार कारक है । उस सटीक स्थान के िलए जहां कोई प्रस्तािवत WECS बनाया जाना है , एनोमेट्री
डेटा कुछ समय अविध के िलए पर उपलब्ध होना चािहए और स्थान के चयन का िनणर्य लेने से पहले इसे परू ा िकया जाना चािहए ।
The aenometry data should be available over some time period at the precise spot where any proposed
WECS is to be built and that this should be accomplished before a sitting decision is made.
3. प्रस्तािवत स्थल पर िवडं V(t) वक्र क� उपलब्धता Wind structure at the proposed site:-
यह महत्वपणू र् वक्र , हवा में अिधकतम ऊजार् को िनधार्�रत करता है और इसिलए िवद्यतु उत्पादन क� भिवष्यवाणी करने में यह एक
प्रमख
ु प्रारंिभक िनयंत्रण कारक है ।
यह वांछनीय है िक हवा क� औसत गित 'v' ऐसी होिन चािहए िक v>=12-16 िकमी/घटं ा (3.5 - 4.5 मीटर/सेकंड) हो | v(t) वक्र,
डब्ल्यईू सीएस क� जनरे टर शि� क� िव�सनीयता को भी िनधार्�रत करता है , यिद v(t) वक्र शन्ू य हो जाता है , तो उस समय के दौरान
कोई उत्पन्न शि� नहीं होती है ।
कम शांत-अविध है क� तुलना में , लंबी शांत-अविध में WECS क� िव�सनीयता में कमी होगी । िव�सनीयता के उच्चतम स्तर का
अनमु ान करने के िलए लगभग 5 वषर् क� अविध के V(t) वक्र का मापना वांछनीय है ।
This important curve determines the maximum energy in the wind and hence is the principal initially
controlling factor in predicting the electrical output and hence revenue return o the WECS machines.
It is desirable to have average wind speed ‘V’ such that V>=12-16 km/hr (3.5 – 4.5 m/sec). The V(t) Curve
also determines the reliability of the delivered WECS generator power, for if the V(t) curve goes to zero
there be no generated power during that time.
If there are long periods of calm the WECS reliability will be lower than if the calm periods are short. In
making such reliability estimates it is desirable to have measured V(t) Curve over about a 5 year period for
the highest confidence level in the reliability estimate.
4. प्रस्तािवत स्थल क� पवन सरं चना : Wind structure at the proposed site:
4
WIND TURBINE
WECS के िलए आदशर् िस्थित ऐसी साइट होगी , जहां का V (t) वक्र सपाट हो , यानी हर समय smooth steady wind बहती
चलती रहे | लेिकन कोई भी चयिनत िविश� साइट , हमेशा आदशर् साइट से कम ही होती है । हवा िवशेष �प से जमीन के पास
अशांत और तेज होती है , और तेजी से िदशा और वेग बदलती है । The ideal case for the WECS would be a site such
that the V(t) Curve was flat, i.e., a smooth steady wind that blows all the time; but a typical site is always
less than ideal. Wind specially near the ground is turbulent and gusty, and changes rapidly in direction and
in velocity.
5. प्रस्तािवत स्थल क� ऊंचाई: Altitude of the proposed site:
यह वायु घनत्व को प्रभाव करके हवा क� शि� प्रभािवत करता है और इसिलए WECS द्वारा िवद्यतु शि� के उत्पादन के िलए
उपयोगी है। इसके अलावा, जैसा िक सवर्िविदत है , हवा क� गित, अिधक ऊंचाई पर अिधक होती है। It affects the air density
and thus the power in the wind and hence the useful WECS electric power output. Also, as is well known,
the wind tend to have higher velocities at higher altitudes.
6. भू-भाग और इसके वायुगितक�य: Terrain and its aerodynamic:
चनु ी जाने वाली साइट के इलाके के बारे में पता होना चािहए । यिद WECS को शीषर् के पास रखा जाना है , लेिकन इसको हवा का
सामना करने वाली blunt hill (पहाड़ी) के शीषर् पर नहीं होना चािहए , ऐसा होने पर हवा के वेग क� 'गित-अप' प्रा� करना सभं व हो
सकता है, जो अन्यथा नही होगा । साथ ही यहां हवा को �ैितज �प से प्रवािहत नहीं होना चािहए, अन्यथा रोटर क� धरु ी को िटप करना
आवश्यक हो जाता है तािक एयरोटबार्इन हमेशा वास्तिवक हवा प्रवाह के लंबवत बहे । One should know about terrain of the
site to be chosen. If the WECS is to be placed near the top but not on the top of a not too blunt hill facing
the prevailing wind, then it may be possible to obtain a ‘speed-up’ of the wind velocity over what it would
otherwise be. Also the wind here may not flow horizontal making it necessary to tip the axis of the rotor so
that the aeroturbine is always perpendicular to the actual wind flow.
7. स्थानीय पा�रिस्थितक� Local Ecology
यिद सतह base rock है, तो यहाँ हब ऊंचाई कम रखी जा सकती है और ऐसा करने पर संरचना लागत कम आती है । यिद आसपास
पेड़ या घास या वनस्पित मौजदू में हवा को न� करने क� प्रवृि� होती हैं , इसिलए हब को अिधक पर रखने क� आवश्यकता पड़ती है |
िजसके प�रणामस्व�प जमीन पर आधार बढाने के कारण प्रणाली पर अिधक व्यय क� आवश्यकता पड़ती है । If the surface is
base rock it may mean lower hub height hence lower structure cost. If trees or grass or vegetation are
present, all of which tend to destructure the wind, the higher hub heights will be needed resulting in larges
system costs that the bare ground case.
8. सड़क या रेलवे से दूरी: Distance to road or railways:
यह एक अन्य कारक है िजसमें भारी मशीनरी , संरचना, सामग्री, ब्लेड और अन्य उपकरण को िकसी भी चयिनत WECS साइट में ले
जाने के िलए िवचार पर िकसी िसस्टम इजं ीिनयर को करना चािहए। This is another factor the system engineer must
consider for heavy machinery, structure, materials, blades and other apparatus will have to be moved into
any choosen WECS site.
9. स्थानीय कें द्र/उपयोगकतार्ओ ं के िलए साइट क� िनकटता Nearness of site to local centre/users::
इस प्रकार का मानदडं स्प� �प से संचरण लाइन क� लंबाई को कम करके हािनयाँ और लागत में कमी लाता है। िपछले सभी िस्ट्रंग
मानदडं ों को लागू करने के बाद, उम्मीद है िक प्रस्तािवत डब्ल्यईू सीएस साइटों को एक या दो तक सीिमत कर िदया जाएगा , वे उत्पन्न
िवद्यतु ऊजार् के उपयोगकतार् के अपे�ाकृ त िनकट होंगे। This obvious criterion minimizes transmission line length and
hence losses and cost. After applying all the previous string criteria, hopefully as one narrows the proposed
WECS sites to one or two they would be relatively near to the user of the generated electric energy.
10. मैदान क� प्रकृित Nature of ground::
5
WIND TURBINE
जमीनी िस्थित ऐसी होनी चािहए तािक WECS क� नींव सरु ि�त हो सके । जमीन क� सतह ठोस होनी चािहए इससे कटाव क� समस्या
नहीं होनी चािहए , क्योंिक यह संभवतः बाद में WECS क� नींव को धराशाई करके , परू े िसस्टम को न� कर सकता है । Ground
condition should be such that the foundation for a WECS are secured. Ground surface should be stable.
Erosion problem should not be there, as it could possibly later wash out the foundation of a WECS,
destroying the whole system.
11. अनुकूल भूिम लागत Favorable land cost::
भिू म क� लागत अनक ु ू ल होनी चािहए क्योंिक यह साईट चयन क� अन्य लागतों के साथ कुल WECS प्रणाली लागत में जडु ती है ।
Land cost should be favourable as this along with other siting costs, enters into the total WECS system
cost.
12. अन्य िस्थितयाँ जैसे आइिसंग क� समस्या , नमक स्प्रे या उड़ती ह�ई धलू साइट पर मौजदू नहीं होनी चािहए , क्योंिक वे
एयरोटरबाइन ब्लेड को प्रभािवत कर सकती हैं या इस प्रकार का पयार्वरण आमतौर पर मशीनरी और िवद्यतु उपकरण के िलए प्रितकूल
होता है । Other conditions such as icing problem, salt spray or blowing dust should not present at the site, as
they may affect aeroturbine blades or environmental is generally adverse to machinery and electrical
apparatus.
१. HORIZONTAL AXIS WIND TURBINE :- पवन टबार्इन एक ऐसा उपकरण है, जोिक पवन ऊजार् को िवद्यतु ऊजार् में
प�रवितर्त करता है । पवन क� गितज ऊजार् प्रारंिभक �प में पवन टबार्इनों क� घणू नर् मान शाफ्ट में यांित्रक ऊजार् में �पांत�रत होती है ।
जनरे टर का उपयोग यांित्रक ऊजार् को िवद्यतु ऊजार् में बदलने के िलए उपयोग िकया जाता है । आधिु नक पवन टबार्इन, िविभन्न आकारों
में आते हैं , लेिकन व्यावहा�रक �प से सभी में तीन प्रमखु खंड और कई सहायक भाग होते हैं । रोटर ब्लेड , नैकेले और टावर इसके
प्रमख
ु भाग होते हैं । िचत्र में एक िविश� पवन टरबाइन के िविभन्न घटकों का योजनाबद्ध िचत्रण प्रदिशर्त िकया गया है । A wind
turbine is a device that transforms wind energy into electrical energy. The kinetic energy of the wind is
initially transformed in wind turbines into the mechanical energy of a revolving shaft. A generator is then
used to turn the mechanical energy into electrical energy. Modern wind turbines come in a variety of sizes,
but practically all of them have three major sections and numerous auxiliary parts. The rotor blades,
nacelle, and tower are its principal parts. Fig. displays a schematic illustration of the various components of
a typical wind turbine.
Rotor Blades: रोटर ब्लेड:- ब्लेड में आमतौर पर एक सपाट और सामान्य �प से घमु ावदार प� होता है। ये ब्लेड ठोस स्टील के
बजाय खोखले , हल्के समग्र सामग्री से बने होते हैं । आमतौर पर तीन ब्लेड मौजदू होते हैं । रोटर ब्लेड को िचत्र में िदखाया गया है ।
The blade typically has a flat side and a normally curved side. These blades are built of hollow, lightweight
6
WIND TURBINE
composite materials rather than being solid steel. Three blades are typically present. The picture of a rotor
blade is presented in Fig..
Nacelle: नैकेले:- इसमें ड्राइव ट्रेन , शाफ्ट, िगयर बॉक्स, जनरे टर और इलेिक्ट्रकल िसस्टम जैसे कई घटक होते हैं। रोटर ब्लेड, िगयर
बॉक्स द्वारा जनरे टर से जड़ु े होते हैं । िगयर बॉक्स, कम गित वाले शाफ्ट को उच्च गित वाले शाफ्ट से जोड़ता है, जहां घणू � गित को
लगभग 30-60 revolution प्रित िमनट (आरपीएम) से बढ़ाकर लगभग 1000-1500 आरपीएम कर िदया जाता है। इसके बाद
जनरे टर, रोटर ब्लेड क� घणू � ऊजार् को िवद्यतु ऊजार् में प�रवितर्त करता है। िचत्र में िगयर बॉक्स और जनरे टर क� एक तस्वीर िदखाई गई
है । It contains several components like drive train, shafts, gear box, generator and electrical system. The
rotor blades are connected to the generator by gear box. The gear box connects the low-speed shaft to the
high-speed shaft where the rotational speed is increased from about 30-60 revolution per minute (rpm) to
approximately 1000-1500 rpm. The generator is then converts the rotational energy of the rotor blades to
the electrical energy. A picture of gear box and generator are shown in Figs.
Tower: टॉवर: टॉवर के शीषर् पर रोटर ब्लेड और नैकेल िस्थत होते हैं । आम तौर पर , इसको स्टील क� गोल ट्यबू लर आकार में
बनाया जाता है । टावर क� ऊंचाई आमतौर पर 50-100 मीटर तथा व्यास लगभग 3-4 मी होता है । Rotor blades and nacelle
are mounted on the top of a tower. Generally, it is made with steel in round tubular shape. The height of the
tower is usually 50 - 100 m and diameter is about 3-4m.
एक िविश� प्रत्य� ड्राइव प्रकार के �ैितज अ� छोटे पवन टरबाइन के मख्ु य घटक हैं: Main components of a typical direct
drive type horizontal axis small wind turbine are:
1. रोटर ब्लेड टबार्इन ब्लेड बेहतर प्रदशर्न के िलए हल्के पदाथ� से बने होती हैं। :Rotor blades: Turbine blades are made
with lightweight materials for better performance.
7
WIND TURBINE
2. रोटर हब: यह ब्लेड को पकड़कर इनको टरबाइन के मख्ु य शाफ्ट से जोड़ता है । Rotor hub: It hold the blades and
connect them to the main shaft of the turbine.
3. टेल वेन: ब्लेड को हवा क� िदशा में करने के िलए उपयोग िकया जाता है । Tail vane: Used to point the blades in the
direction of the wind.
4. जनरे टर जनरे टर शाफ्ट क� यांित्रक शि� को िवद्यतु शि� में प�रवितर्त करता है। :Generator: Generator converts the
mechanical power of the shaft into electrical power.
5. टावर : यह टबार्इन क� संरचना को सहारा देता है। रोटर ब्लेड और नैकेल टावर के ऊपर पर लगे होते हैं । आम तौर पर, इसको स्टील
क� गोल ट्यबू लर आकार में बनाया जाता है । Tower: It supports the structure of the turbine. Rotor blades and
nacelle are mounted on the
top of the tower. Generally, it is made with steel in round tubular shape.
6. . फाउंडेशन: इसे पवन टरबाइन के भार को िमट्टी क� गहराई में स्थानांत�रत करने और फै लाने के िलए िडज़ाइन िकया गया है ।
Foundation: It is designed to transfer and spread the load of the wind turbine to the soil at depth.
कायर्कारी िसद्धांत :-
डायरे क्ट ड्राइव टाइप हॉ�रजॉन्टल एिक्सस स्मॉल िवडं टबार्इन क� कायर्प्रणाली इस प्रकार है:
1. सबसे पहले, पवन ऊजार्, रोटर ब्लेड को प्रा� होती है । रोटर ब्लेड, हवाई जहाज के पख ं क� तरह काम करते हैं। जब हवा चलती है,
तो इससे ब्लेड के एक तरफ कम वायदु ाब बनता है।
2. यह िनम्न वायदु ाब ब्लेड को अपनी ओर खींचता है। इसे "िलफ्ट" कहा जाता है। ब्लेड आकार फ्लैट हैं , यह “िलफ्ट” को बढ़ाता है
और प�रणामस्व�प रोटर शाफ्ट घमू ने लगता है ।
3. यह िलफ्ट-बल, ब्लेड के सामने क� ओर से कायर् करने वाले वायु बल से कहीं अिधक मजबतू होता है. िजसे "ड्रैग" कहा जाता है।
“िलफ्ट” और “ड्रैग” का यह सयं ोजन रोटर को प्रोपेलर क� भाँती घमु ाने का कारण बनता है ।
4. पवन क� गितज ऊजार्, रोटर के प�रक्रमण द्वारा यांित्रक ऊजार् में बदलती है । यह यांित्रक ऊजार् , शाफ्ट के माध्यम से जनरे टर क� ओर
प्रेिषत क� जाती है ।
5. अंत में, जनरे टर, िवधतु उत्पादन के िलए यांित्रक ऊजार् को िवद्यतु ऊजार् में प�रवितर्त करता है ।
Working:
The working of a direct drive type horizontal axis small wind turbine is as follows:
1. Firstly, the wind energy is received by the rotor blades. Rotor blades act like an aeroplane wing. When
the wind blows, a low air pressure is created on one side of the blade.
2. This low air pressure pulls the blade towards it. This is called as “lift”. Blades are flat in shape which
increase the lift and as a result the rotor shaft starts rotating.
3. The force of this lift is much stronger than wind force acting from the front side of the blade which is
called as “drag”. This combination of lift and drag causes rotor to rotate like a propeller.
4. The kinetic energy of the wind changes into mechanical energy through the revolution of the rotor. This
mechanical energy is transmitted through the shaft towards the generator.
5. Finally, the generator converts the mechanical energy into electrical energy to generate electricity.
2. VAWT :- In vertical axis wind turbine, the axis of rotation of rotor shaft is perpendicular to the
ground. The rotor shaft is also perpendicular to the direction of the wind. The main components like gear
box, generator etc. are placed at the base of the turbine which makes its service and repair easy. Nacelle is
8
WIND TURBINE
not required in VAWT. These turbines are found lighter in weight and cheaper in cost. VAWT are mostly
used in small wind industries and residential area. They capture the wind from all directions so no need to
be pointed towards the wind. Tall towers and long blades are not required for VAWT. Though the VAWT
has many advantages over HAWT but they are less efficient and produces less energy as compared with
HAWT.
(a) सवोिनयस प्रकार: इसका आिवष्कार सबसे पहले एक िफिनश वास्तक ु ार और एस.जे. सवोिनयस ने िकया । 1929 में इस
आिवष्कार का पेटेंट कराया गया। सवोिनयस रोटर में S-आकार के दो घमु ावदार धातु के air foils होते हैं । air foils को ऊपर और
नीचे से दो गोलाकार प्लेटों द्वारा सपोटर् िकया जाता है। यह देखने पर S-शेप जैसा िदखता है |
यह ड्रैग टाइप VAWT होता है, जोिक रोटर को चलाने के िलए ड्रैग फोसर् का उपयोग करता है । यह एक धीमी गित से घमू ने वाली
उच्च टॉकर् मशीन होती है । एक सैवोिनयस टाइप VAWT का एक वास्तिवक फोटोग्राफ और योजनाबद्ध आरे ख को िचत्र में दशार्या
गया है ।
9
WIND TURBINE
:डे�रयस प्रकार (b)डै�रयस प्रकार क� पवन टरबाइन को आमतौर पर इसके आकार के कारण Eggbeater के �प में जाना जाता है ।
इसमें दो या तीन घमु ावदार ब्लेड होती हैं । इसको lift force द्वारा सचं ािलत होता है । में जॉज�स डे�रयस द्वारा इसका आिवष्कार 1931
िकया गया था । यह एक उच्च गित और कम बलघणु र् क� मशीन है जो आमतौर पर प्रत्यावत� िवधतु उत्पन्न करने के िलए उपयोग क�
जाती है क्योंिक इसका स्टािट�ग टॉक , ब्लेड के प्रािम्भक चालन में इसके िलए कुछ बाहरी शि� स्रोत क� आवश्यकता हो सकती है |
10
WIND TURBINE
बह�त कम होता है । डै�रयस प्रकार का एक वास्तिवक फोटोग्राफ और योजनाबद्ध आरे ख VAWT को िचत्र में दशार्या गया है |(b)
Darrieus type: Darrieus type wind turbine is commonly known as Eggbeater because of its shape. It
consists of two or three curved blades. It is driven by lift force. It was invented by Georges Darrieus in
1931. It is a high speed and low torque machine generally used for generating AC electricity. Initial
movements of the blades may require some external power source because starting toque is very low. An
actual photograph and schematic diagram of a Darrieus type VAWT is depicted in Fig.
एक ऊध्वार्धर अ� पवन टरबाइन का मख्ु य रोटर शाफ्ट ऊध्वार्धर िदशा में जमीन पर व्यविस्थत होता है । जनरे टर और अन्य प्राथिमक
भागों को टरबाइन के आधार पर रखा जाता है । प्रत्य� ड्राइव प्रकार में ऊध्वार्धर अ� पवन टरबाइन में रोटर शाफ्ट सीधे जनरे टर से
िबना िगयर बॉक्स के जड़ु ा ह�आ होता है । डै�रयस टाइप विटर्कल एिक्सस स्मॉल िवंड टबार्इन क� िविश� डायरे क्ट ड्राइव का लेआउट
िचत्र में िदखाया गया है । डै�रयस टाइप स्मॉल िवंड टबार्इन के मख्ु य घटक हैं : The main rotor shaft of a vertical axis wind
turbine is arranged in the vertical direction to the ground. Generator and other primary parts are placed at
the base of the turbine. In direct drive type vertical axis wind turbine rotor shaft is directly connected to the
generator without gear box. The layout of typical direct drive Darrieus type vertical axis small wind turbine
is shown in Fig. .The main components of a Darrieus type small wind turbine are:
1. गाइड वायर: यह रोटर शाफ्ट को लंबवत में िस्थर अवस्था में रखने में मदद करता है ।
2. हब: यह रोटर ब्लेड को पकड़कर शाफ्ट से जोड़ता है । अिधकतम वायगु ितक�य द�ता प्रा� करने के िलए इसे ब्लेड को उिचत
िस्थित में रखना चािहए। VAWT में, रोटर ब्लेड, ऊपरी हब और िनचले हब पर दो िबदं ओ ु ं से जड़ु े ह�ए होते हैं ।
3. रोटर ब्लेड: डे�रयस प्रकार क� छोटी पवन टरबाइन में वक्र आकार क� रोटर ब्लेड का उपयोग िकया जाता है। ब्लेड एल्यमू ीिनयम या
FRP से बने होते हैं, क्योंिक ये बेहतर सामथ्यर् प्रदान करते हैं ।
4. शाफ़्ट : यह टरबाइन का वह भाग है, जोिक ब्लेड के साथ घमू ता है। यह main housing में जनरे टर से जड़ु ा ह�आ होता है।
5. जनरे टर: यह टबार्इन का एक घटक है जोिक घणू नर् क� यांित्रक ऊजार् को िवद्यतु ऊजार् में प�रवितर्त करता है । डे�रयस टाइप विटर्कल
एिक्सस िवंड टबार्इन में, इसे जमीन पर बेस बना कर रखा जाता है।
6. टबार्इन बेस: यह आम तौर पर एक इमारत क� जमीन या छत होती है, िजस पर डै�रयस टरबाइन स्थािपत होती है ।
1. Guide wire: It helps in keeping the rotor shaft vertically in a foxed position.
2. Hub: It hold the rotor blade and connect them to the shaft. It must hold the blade in its proper position to
get maximum aerodynamic efficiency. In VAWT, the rotor blades are attached at twopoint, upper hub and
lower hub.
3. Rotor blades: Curve shaped rotor blades are used in Darrieus type small wind turbine. Blades are made
up aluminum or FRP because they provide better strength.
4. Shaft: It is the part of the turbine which turns with the blades. It is connected to the generator in the main
housing.
5. Generator: It is component of the turbine which converts mechanical energy of rotation to the electrical
energy. In Darrieus type vertical axis wind turbine, it is placed at the base on the ground.
6. Turbine base: It is generally the ground or roof of a building on which Darrieus turbine is installed.
कायर्कारी िसद्धांत :-
11
WIND TURBINE
जब एयरो फॉइल रोटर ब्लेड, पवन ऊजार् प्रा� करते हैं, तो टबार्इन का मख्ु य शाफ्ट, िजसमें हब्स के सपोटर् से ऊपरी और िनचले िबंदु पर
ब्लेडस जडु ी ह�ई रहती है , घमू ना श�
ु कर देता है। शाफ्ट द्वारा गितज ऊजार् को यांित्रक ऊजार् में प�रवितर्त िकया जाता है। यह यांित्रक
ऊजार् आधार के पास रखे जेनरे टर को स्थानांत�रत क� जाती है । जनरे टर, िवधतु उत्पादन हेतु यांित्रक ऊजार् को िवद्यतु ऊजार् में प�रवितर्त
करता है । Working: When the aero foils rotor blades receive the wind energy. The main shaft of the turbine
which is connected to the blade at upper and lower point with the help of hubs start rotating. The kinetic
energy is converted into mechanical energy through the shaft. This mechanical energy is then transferred to
the generator placed near the base. The generator converts the mechanical energy into electrical energy to
produce electricity.
डायरे क्ट ड्राइव टाइप विटर्कल एिक्सस स्मॉल िवंड टबार्इन के गणु और दोष
गणु :
1. िगयर वाली पवन टबार्इनों क� तुलना में अिधक कुशल ।
2. यह बेहतर प्रदशर्न करता है |
3. चिंू क इसमें िकसी प्रकार के िगयर बॉक्स क� आवश्यकता नहीं होती है, इसिलए इसमें कम रखरखाव क� आवश्यकता होती है ।
दोष:
1. िगयर प्रकार के पवन ऊजार् सयं त्रं क� तल
ु ना में प�रवहन समस्या अिधक है |
2. यांित्रक और िवद्यतु चम्ु बक�य सरं चना में सधु ार क� आवश्यकता है ।
Merits and Demerits of Direct Drive Type Vertical Axis Small Wind Turbine Merits:
1. More efficient than geared type wind turbines.
2. It gives better performance
3. Since no gear box needed, it requires less maintenance.
Demerits:
1. Transportation problem is more as compared with geared type wind power plant
2. Mechanical and electromagnetic structure need to be improved.
12
WIND TURBINE
turbine. turbine.
Axis of rotation For the horizontal axis wind For the vertical axis wind turbine,
with respect to turbine, the axis of rotation of the axis of rotation of the turbine
wind stream turbine is parallel to the wind is perpendicular to the wind
stream. stream.
Location of In the horizontal axis wind In the vertical axis wind turbine,
electric generator turbine, the electric generator the generator is installed on the
is installed at the top of the ground.
tower.
Location of In HAWT, the gearbox is In VAWT, the gearbox is installed
gearbox installed at the top of the at the bottom of the turbine.
turbine tower.
Need of yaw In the horizontal axis wind The vertical axis wind turbine
mechanism turbine, the yaw mechanism is does not require yaw mechanism
required to orient the turbine in because it receives wind from all
the direction of wind. directions.
Self-starting Horizontal axis wind turbine is Vertical axis wind turbine is not
self-starting. self-starting, hence a starting
mechanism is required to start it
from stationary position.
Design and The design and installation of The design and installation of a
installation a horizontal axis wind turbine vertical axis wind turbine is
is complex. comparatively simple.
Operation space of Horizontal axis wind turbine Vertical axis wind turbine requires
blades requires large space for blade’s small space for blade’s operation.
operation.
Dependency on The operation of horizontal The operation of vertical axis wind
wind direction axis wind turbine is dependent turbine is independent of the wind
on wind direction. direction because it receives wind
from all directions.
Height from The height of the horizontal The vertical axis wind turbine is
ground axis wind turbine from ground installed at comparatively smaller
is large. distance from the ground.
13
WIND TURBINE
Need of nacelle In case of horizontal axis wind There is no need of nacelle in case
turbines, a heavy nacelle is of vertical axis wind turbines.
installed at the top of the
tower.
Power coefficient Horizontal axis wind turbine Vertical axis wind turbine has a
has a high power coefficient. low power coefficient.
Tip speed ratio Horizontal axis wind turbine Vertical axis wind turbine has
(TSR) has high tip speed ratio. considerably low tip speed ratio.
Noise produced The operation of horizontal Vertical axis wind turbines
axis wind turbine is noisy. produce comparatively less noise.
Efficiency The ideal efficiency of The ideal efficiency of vertical
horizontal axis wind turbine is axis wind turbine is usually more
around 50% to 60 %. than 70%.
Hindrance for Horizontal axis wind turbines Vertical axis wind turbines cause
birds cause high obstruction for less hindrance for birds.
birds.
Cost Horizontal axis wind turbines Vertical axis wind turbines are less
are more expensive due their expensive because their design and
complex design and installation is quite simple.
installation.
14
WIND TURBINE
समतल �ेत्रों में िस्थत पवन टबार्इन आमतौर पर पहाड़ी �ेत्रों में िस्थत पवन टबार्इनों क� तुलना में अिधक भिू म को उपयोग में लेते हैं।
इस प्रकार टबार्इन स्वयं और आसपास के बिु नयादी ढांचे (सड़कों और ट्रांसिमशन लाइनों सिहत) पवन सिु वधा के कुल �ेत्रफल के एक
छोटे से िहस्से को अिधगृिहत कर लेते हैं । ये प्रित मेगावाट िबजली उत्पादन �मता के 30 और 141 एकड़ के बीच उपयोग करते हैं |
िनमार्ण के दौरान 1 एकड़ प्रित मेगावाट से कम स्थायी �प से और 3.5 एकड़ प्रित मेगावाट से कम अस्थायी �प से बािधत होता है ।
शेष भिू म का उपयोग कई अन्य उत्पादक उद्देश्यों के िलए िकया जा सकता है, िजसमें पशधु न चराई, कृ िष, राजमागर् और लंबी पैदल
यात्रा ट्रेल्स शािमल हैं । वैकिल्पक �प से, पवन सिु वधाओ ं को ब्राउनफ�ल्ड्स (प�रत्य� या अप्रय� ु औद्योिगक भिू म) या अन्य
वािणिज्यक और औद्योिगक स्थानों पर रखा जा सकता है, जो भिू म उपयोग के बारे में िचंताओ ं को काफ� कम कर सकती है । Wind
turbines located in flat areas typically use more land than wind turbines located in mountainous areas. Thus
the turbines themselves and the surrounding infrastructure (including roads and transmission lines) occupy
a small portion of the total area of the wind facility. They use between 30 and 141 acres of electricity
generation capacity per megawatt. Less than 1 acre per MW is permanently and less than 3.5 acres per MW
is temporarily disrupted during construction. The rest of the land can be used for a variety of other
productive purposes, including livestock grazing, agriculture, highways, and hiking trails. Alternatively,
wind facilities can be placed on brownfields (abandoned or unused industrial land) or other commercial and
industrial locations, which can significantly reduce concerns about land use.
वन्यजीव और आवास Wildlife and habitat
पवन टबार्इनों मे हवा के दबाव में बदलाव के कारण िस्पिनंग टबार्इनों के कारण टकराव पि�यों और चमगादड़ों क� मौत के सबतू तथा
आवास व्यवधान पाए गये है । NWCC ने िनष्कषर् िनकाला िक ये प्रभाव हालांिक अपे�ाकृ त कम हैं और प्रजाितयों क� आबादी के
िलए खतरा पैदा नहीं करते । हवा क� कम गित के दौरान पवन टबार्इनों को गितहीन रखने पर िबजली उत्पादन को महत्वपणू र् �प से
प्रभािवत िकए िबना आधे से अिधक चमगादड़ों क� मृत्यु को कम िकया जा सकता है |
अपतटीय पवन टबार्इनों से पि�यों क� मृत्यु न्यनू तम होती है। अपतटीय िस्थत पवन फ़ामर्, मछली और अन्य समद्रु ी वन्यजीवों को भी
प्रभािवत करते है । कुछ अध्ययनों से पता चलता है िक टबार्इन वास्तव में कृ ित्रम चट्टानों के �प में कायर् करके मछली क� आबादी बढ़ा
सकते हैं ।
Evidence of bird and bat deaths from collisions with wind turbines and due to changes in air pressure
caused by the spinning turbines, as well as from habitat disruption. The NWCC concluded that these
impacts are relatively low and do not pose a threat to species populations. keeping wind turbines
motionless during times of low wind speeds could reduce bat deaths by more than half without significantly
affecting power production. The bird deaths associated with offshore wind are minimal. Wind farms
located offshore will also impact fish and other marine wildlife. Some studies suggest that turbines may
actually increase fish populations by acting as artificial reefs.
Public health and community
पवन टबार्इनों के संचालन में सावर्जिनक स्वास्थ्य और सामदु ाियक से जड़ु ी दो मख्ु य िचंताएँ ध्विन और �श्य प्रभाव हैं। पवन टबार्इनों
द्वारा हवा में टरबाइन ब्लेडों क� गित के कारण उत्पन्न अिधकांश ध्विन “वायगु ितक�य” होती है | टबार्इन द्वारा ही यांित्रक ध्विन भी
उत्पन्न होती है ।
पवन सिु वधाओ ं के पास रहने वाले कुछ लोगों ने ध्विन और कंपन के मद्दु ों के बारे में िशकायत क� है, लेिकन अध्ययनों ने पाया है िक ये
मद्दु े सावर्जिनक स्वास्थ्य पर प्रितकूल प्रभाव नहीं डालते हैं । हालांिक , पवन टरबाइन िवकासकतार्ओ ं के िलए यह महत्वपणू र् है िक वे
टबार्इनों को स्थािपत करने और प्रभािवत समदु ाय के सदस्यों के साथ खल ु ा संवाद श�
ु करने के िलए "अच्छे पड़ोसी" तथा सव��म
15
WIND TURBINE
प्रथाओ ं का पालन करके इन सामदु ाियक िचंताओ ं को गंभीरता से लें। इसके अित�र� , तकनीक� िवकास, से जैसे िक ब्लेड क� सतह
क� खािमयों को कम और ध्विन-अवशोषक सामग्री का उपयोग करके , पवन टरबाइन के शोर को कम िकया जा सकता है ।
कुछ प्रकाश प्रभावों के कारण, पवन टबार्इन क� छाया िझलिमलाहट वाला प्रभाव पैदा कर सकते हैं । इस झंझु लाहट को सावधानीपवू र्क
स्थापन, पेड़ लगाकर कम िकया जा सकता है ।
फे डरल एिवएशन एडिमिनस्ट्रेशन (FAA) के िलए आवश्यक है िक 200 फ�ट से अिधक ऊँची सभी संरचनाओ ं क� तरह , बड़ी पवन
टबार्इनों में िवमानन सरु �ा के िलए सफे द या लाल बि�याँ हों । हालांिक , एफएए ने हाल ही में िनधार्�रत िकया है िक जब तक आधे
मील से अिधक प्रकाश व्यवस्था में कोई अंतराल नहीं है , तब तक बह�-टरबाइन पवन प�रयोजना में प्रत्येक टावर को रोशन करना
आवश्यक नहीं है । टबार्इनों को यिद सफे द रंग से रंगा जाता है तो िदन के समय रोशनी अनावश्यक है ।
The two main public health and community concerns associated with the operation of wind turbines are
noise and visual effects. Much of the noise produced by wind turbines is "aerodynamic" due to the motion
of the turbine blades in the air. Mechanical sound is also generated by the turbine itself.
Some people living near wind facilities have complained about noise and vibration issues, but studies have
found that these issues do not adversely affect public health. However, it is important for wind turbine
developers to take these community concerns seriously by following "good neighborly" and best practices
when installing turbines and initiating open dialogue with affected community members. Additionally,
technological advances, such as reducing blade surface imperfections and using sound-absorbing materials,
can reduce wind turbine noise.
Due to some lighting effects, the shadows of wind turbines can create a flickering effect. This annoyance
can be minimized by careful placement of trees.
The Federal Aviation Administration (FAA) requires that large wind turbines, like all structures over 200
feet tall, have white or red lights for aviation safety. However, the FAA recently determined that it is not
necessary to illuminate each tower in a multi-turbine wind project as long as there is no gap in the lighting
system greater than half a mile. If the turbines are painted white then the lights during the day are
unnecessary.
Water use
पवन टबार्इनों के सच
ं ालन पर कोई जल प्रभाव नहीं देखा गया है। हांलांिक सभी िनमार्ण प्रिक्रयाओ ं जैसे स्टील और सीमेंट के िनमार्ण में
कुछ पानी का उपयोग िकया जाता है |
There is no water impact associated with the operation of wind turbines. As in all manufacturing processes,
some water is used to manufacture steel and cement for wind turbines.
Life-cycle global warming emissions जीवनचक्र ग्लोबल वािम�ग उत्सजर्न-
पवन टबार्इनों के प�रचालन से कोई ग्लोबल वािम�ग उत्सजर्न जड़ु ा नहीं है हांलांिक पवन टरबाइन के जीवन-चक्र के अन्य चरणों से
उत्सजर्न जड़ु े ह�ए हैं , िजनमें सामग्री उत्पादन , सामग्री प�रवहन , साइट पर िनमार्ण और असेंबली , संचालन और रखरखाव , और
िडकमीशिनंग और िडसमेंटलमेंट शािमल हैं । .
कुल ग्लोबल वािम�ग उत्सजर्न के अनमु ान कई कारकों पर िनभर्र करते है , िजसमें हवा क� गित, हवा चलने के समय का प्रितशत और
पवन टरबाइन क� सामग्री संरचना शािमल हैं । पवन टबार्इन जीवन-चक्र में ग्लोबल वािम�ग उत्सजर्न में काबर्न डाइऑक्साइड का
अिधकांश अनमु ान 0.02 और 0.04 पाउंड प्रित िकलोवाट-घटं े के बीच है।
16
WIND TURBINE
No global warming emissions are associated with the operation of wind turbines, however there are
emissions associated with other phases of the wind turbine life-cycle, including material production,
material transportation, on-site fabrication and assembly, operation and maintenance, and decommissioning
and dismantling. Estimates of total global warming emissions depend on several factors, including wind
speed, the percentage of time the wind is blowing, and the material composition of the wind turbine. Most
estimates of carbon dioxide in global warming emissions over the wind turbine life-cycle are between 0.02
and 0.04 pounds per kilowatt-hour.
17