‘TEXAS AVIATION SERVICES, INC. ICA FOR AGUSTAS.p.A.
3901 NORTH MAIN STREET MODEL A109E S/N: 11756
FORT WORTH, TX 76106 WHELEN LED POSITION/STROBE ASSEMBLY
INSTRUCTIONS FOR CONTINUED AIRWORTHINESS
FOR
AUGUSTA A109E
Registration Number: N109HX
Serial Number: 11756
WITH
Whelen LED Position/Strobe Assembly
90340( )-Series Installed
DOC No. 16402330001eee DATE:
03/01/2011
THE
‘DoT Ra PAGE
16402330001 NC 10f5
Instructions for Continued Airworthiness for Augusta A109E
with Whelen LED Position / Strobe Assembly Installed.
LIST OF REVISIONS
REV] DESCRIPTION
WRITTEN | APPROVED | DATE |
BY j>__ BY 4
NG _| ORIGINAL RELEASE _
RWRIGHT Va%nyu Wok NPR D7 2p]
‘Typed signatures indicate approval. Handwritten signature approval of this document ate on fle at RSG
AcroDesign, LLC.Dare DOC Ne: fae | PAGE
03/01/2011 16402330001 NC 20f5
Tite
Instructions for Continued Airworthiness for Augusta A109E
with Whelen LED Position / Strobe Assembly Installed.
Table of Contents
LIST OF REVISIONS
1. INTRODUCTION.
1.1 Purpose.
12 Scope.
13 Retention...
Description of Alteration...
Control, Operating Information ...
Servicing Information ..
Troubleshooting Information...
Removal and Replacement Information
Diagrams ....
2.
3.
4.
5. Maintenance Instructions...
6.
7,
8.
9.
Special Inspection Requirements.......
10. Application of Protective Treatments ...
| 11. Data Relative to Structural Fasteners.
12. Special Tools
13, Additional Instructions
| 14. Overhaul Period.......
15. Airworthiness Limitations Section
AOaananne RARER OB ww Ow
16. Revisions...Dae BOER oe Tage
03/01/2011 16402330001 NC 30f5
Tie
Instructions for Continued Airworthiness for Augusta A109E
with Whelen LED Position / Strobe Assembly Installed.
1.
ny
INTRODUCTION
4.4 Purpose
This document is designed for use by the installing agency of the Whelen LED
Position/Strobe Light Assembly's and LED Anti-Collision Light 90340( )-Series as
Instructions for Continued Airworthiness in response to 14 CFR 27.1529, and Part 27
Appendix A. This ICA includes information required by the operator to adequately
‘maintain the Whelen LED PositioryStrobe Light Assembly's and LED Anti-Collision Light
90340( )-Series installed in a AUGUSTA A109E helicopter under an approved FAA form
337.
1.2 Scope
This document identifies the Instructions for Continued Airworthiness for the
modification of the aircraft for installation of the Whelen LED Position/Strobe Light
Assembly's 90340( )-Series.
1.3. Retention
This document, or the information contained within, will be included in the aircrafts
permanent records.
Description of Alteration
‘The Mode! 90340( )-Series System consists of 3 LED's for forward position lights and 2
aft LED's along with a flashtube for the strobe. The 90340( )-Series was designed to
replace the existing NAV lights typically seen mounted on most general aviation, and
helicopter applications.
» Control, Operating Information
Operation of the Whelen position lights (RED and GREEN) are controlled by a toggle
‘switch located in the overhead switch panel, labeled “POS”. The strobe lights are
controlied by a toggle switch located in the overhead switch panel and labeled
“STROBE”. The anti-collision light is controlled by a toggle switch located in the
overhead switch panel labeled as “ANTI-COLL).
- Servicing Information
No special servicing is required.Dae ‘DoCWe arena
03/01/2011 16402330001 NC 4of5
THE:
Instructions for Continued Airworthiness for Augusta A109E
with Whelen LED Position / Strobe Assembly Installed.
5. Maintenance Instructions
Maintenance of the Whelen LED position lights are ON CONDITION only. Periodic
maintenance is not required. The maintenance instructions presented in the ICA are
limited to the removal, installation and routine maintenance of the unit only.
6. Troubleshooting Information
any LED fails, the unit must be repaired or replaced. Inspect the lenses for excessive
scratches, pitting or discoloration and replace as necessary.
a) Reference Whelen installation Document #14112A, 05131 Rev B & RSG.
Aerodesign Document 08402330004 Rev NC
7. Removel and Replacement Information
Removal:
1. Remove hardware as needed to remove the suspect defective item and save for
reinstallation, if hardware is damaged or worn replace with new like hardware.
2. Ifthe unit is removed and reinstalled, an abbreviated correspondence check
must be conducted to ensure correct operation.
Installation:
1. Reinstallation shall be in reverse order with the same hardware that was
removed if not damaged, otherwise install new hardware and ensure correct
operation.
a) Reference Whelen Installation Document #141 12A, 90340( )-Series LED
Position/strobe light assembly.
8. Diagrams
Model 20340( )-Series LED, Refer to Whelen installation Guide 14112A or later and RSG
Aerodesign Document 08402330004 Rev NC.
9. Special Inspection Requirements
No special inspections requirements,Dae Doe: ca PAGE
03/01/2011 16402330001 NC 5of5
Tine
Instructions for Continued Airworthiness for Augusta ALOSE
with Whelen LED Position / Strobe Assembly Installed.
10. Application of Protective Treatments
No special protective.coatings or treatments are required.
11. Data Relative to Structural Fasteners
The LED housing/ assembly is mounted using standard aircraft hardware as required by
the installation. Any hardware found damaged on inspection or damaged during
removal should be replaced with like hardware on installation. See Whelen Anti-
Collision Light Systems Installation and Service manual Documents listed below:
Model 90840( )-Series, Refer to Installation Manual 141124 or later.
12. Special Tools
No Special tools are required.
13. Additional instructions
This installation is not for commuter category aircraft; therefore no additional ICA
Instructions are required.
14, Overhaul Period
The system does not require overhaul at a specific time period.
15. airworthiness Limitations Section
No Airworthiness Requirements.
16. Revisions
Includes information on how to revise the ICA. For example, a letter will be submitted to
the local FAA Office with a copy of the revised FAA Form 397 and revised ICA. The FAA
inspector accepts the change by signing block 3 and including the following statement,
“The attached revisec/new Instructions for Continued Airworthiness (date___) for the
above aircraft or component major alteration have been accepted by the FAA,
superseding the Instructions for Continued Airworthiness (date ” After the
revision has been accepted, a maintenance record entry will be made, identifying the
revision, its location, and date on the FAA Form 337.