Professional Documents
Culture Documents
MS-15 MUDLINE
®
SUSPENSION SYSTEMS
www.dril-quip.com
MS-15 Mudline Suspension Systems
®
Table of Contents
• Shoulder Hangers . . . . . . . . . . . . . . . . . . . . . . . . . . 4
• Accessory Tools . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Mudline-Related Products . . . . . . . . . . . . . . . 14
1
MS-15 Mudline Suspension System
Dril-Quip’s unique MS-15
Mudline Suspension System
is a series of casing hangers
that support the weight of
each casing string at or near
the mudline. Designed for use
with bottom-supported drilling
vessels and platforms,
the system allows disconnect
from and reconnect to the well
at the mudline.
System Features
• High pressure capacity; • Designed with large
system rated for 15,000 psi flow-by areas
working pressure • Subsea completion possible
• High load capacity at each with Dril-Quip’s Mudline
hanger interface Conversion System
• Easy handling, trouble- • Critical service configurations
free operation available
• Hangers have left-hand • Extra metal-to-metal sealing
running threads, right-hand for higher pressure and
tie-back threads critical service
• Metal-to-metal seals on • Extra centralization for
running and tie-back tools high-angle drilling
with resilient backup seals • Heavier wall for greater load
• Automatic centralization and pressure capacity
ensures concentricity • Fully tested
• Stack-down system for • Field-proven technology
washout efficiency and
easy access to tie-back • Torque tool option available
thread profile for running tools
• Designed for tempo-
rary abandonment
2
MS-15 System Components
Drilling Phase
Running Tools
3
Shoulder Hangers
Features
• High pressure, high Single Load Shoulder
load capacity for Shoulder Hanger
• Easy installation; weight-
set hanger
• Field-interchangeable landing
rings accommodate changes
in casing programs
Shoulder Hanger with Multiple Load Shoulder
Hanger Profile and Split Ring Hanger Installed
• Large flow-by areas for run-
ning and cementing Running Tool Metal-
to-Metal Seal Area
• Full 360-degree load-
bearing area on landing Right-Hand
ring for maximum load- Tie-Back Threads
carrying capacity Left-Hand
Running Threads
• Unique, two-step landing ring provides automatic
centralization when landed Tie-Back Tool Metal-
to-Metal Seal Area
• Independent metal-to-metal sealing surfaces; one for
running tools, one for tie-back tools Two-Step
Landing Ring
4
Split Ring Hangers
Features
• High pressure, high • Positive backup of split ring
load capacity when landed
• Large flow-by areas during • Detent ring allows hanger
running and cementing resetting while eliminating shear
• Unique design ensures full pins and tensile coupons
engagement of each split • Dual metal-to-metal seals;
ring load shoulder with one for running tools, one for
mating profile tie-back tools
5
Mudline Hanger Running Tools
Features
• High pressure, high load capacity
• Low torque make-up
• Self-aligning profile allows full alignment with
hanger prior to thread engagement
• Slots for direct make-up of running tool with
torque tool are optional
• Optional stab-in running tools for
mudline hangers 16" and larger eliminate
left-hand rotation
• Dual O-rings above washports
• Seal below washport never exposed during
wash operations
• One-way seal on nose of pin prevents pressure
OPEN CLOSED OPEN
lock during make-up
• Field-proven performance
Right-hand rotation of approximately six turns opens wash- Right-hand rotation of approximately six turns with weight
ports for washout of casing. After washout, running tool is picked up opens washports for washout of casing. After wash-
made up with six turns to the left. out, weight is slacked off and running tool is made up.
6
Profile Cleanout Tools
TATAcap
cap running
runningandand
retrieving tool installing
retrieving tool ins-
talling aa TA
TA capcap
withwith
back-pressure valve valve
back-pressure
Vented TATA
VENTED Cap CAP
Features
Tie-Back Profile Cleanout Tool Temporary Abandonment Cap
Mill and Flush Tool
• Runs on drill pipe
• Uses top of hanger as reference
• Available for any size
point for positioning washout
Dril-Quip TA cap
holes at tie-back threads and
• Mills large debris from around tie-back sealing surface
TA cap mandrel
• Available for any size Dril-Quip
• Jetting nozzles wash debris from mudline hanger
around TA cap mandrel
Tie-back profile cleanout tool cleaning out TA cap mill and flush tool cleaning TA cap
tie-back threads and metal-to-metal seal running and retrieving mandrel
9
Tie-Back Phase
Tie-Back Phase
System Features
• System stacks down to fully expose
tie-back threads
• Reliable metal-to-metal sealing
• Tie-back threads and sealing areas are
unused and protected during drilling
• Hangers have left-hand running threads,
right-hand tie-back threads
• All strings tie back using
right-hand rotation
Split Ring
Detent Ring
Stab-In Tie-Back Tools
10
Tie-Back Tools
Tie-Back Torque Tool
Tie-Back
Torque Tool
Threaded
Tie-Back Tool
Stab-In
Tie-Back Tool
11
Mudline Conversion System
Mudline
MUDLINE
Tubing Hanger
12
Dril-Thru™ Mudline Completion System
Tubing
Hanger
Running
Tool
Tubing
Hanger
Mudline
Hanger
Wellhead
Housing
20"
Dril-Thru
Mudline
Hanger
Production
Casing
Hanger
13
Dril-Quip: A S ingle-Source Supplier
CRITICAL SERVICE SYSTEM
CS-10™ Casing Support System Critical Service System
Drilling M
DRILLING ode
MODE Tie-Back PRODUCTION
TIE-BACK Production
The CS-10 Casing Support System is used primarily in platform applications
to decreaseCS-10™
load on theCASING SUPPORT
platform by hanging SYSTEM
casing off at the mudline.
Multi-Thread™ Connectors
Dril-Quip fabricates
complete casing joints
for both drilling and
driving applications.
Dril-Quip offers a variety
of connectors that are
Quik-Thread® Connectors ideal for use with mudline
suspension equipment.
Quik-Jay™ Connectors
14
for Mudline-Related Products
D ril-Quip
offers traditional and unitized surface
wellheads for use in with its mudline suspension
product line for jacket and platform applications. The
company’s surface wellhead equipment is offered in a
variety of sizes, configurations and service ratings.
Dril-Quip’s unitized surface wellheads feature metal-
to-metal sealing technology and simplified operational
procedure to reduce installation time.
SC-90™
SC-90™ Conventional
CONVENTIONAL SU-90™UNITIZED
SU-90™ Unitized
Wellhead SSYSTEM
WELLHEAD ystem Wellhead SSYSTEM
WELLHEAD ystem
(psi)
YIELD
PRESSURE PRESSURE
RETURN
AREA
(x 1,000 lbs) (sq in)
MAX.
OD
(inches)
HANGER WILL
RUN THROUGH
MIN. ID
BIT
SIZE
(inches) (inches)
30 — — 2,900 — — — 20.125 20
30 x 13 /8 3
SH 9,700 2,900 28 21.125 21 /4" BOP
1
12.490 12 1/4
Dril-Q uip manufactures and stocks a wide variety of mudline suspension systems to
13 3/8 x 9 5/8 SP 16,500 2,000 10 12.188 13 3/8" x 72 lb/ft. Csg. 8.803 8 3/4
match most casing programs. The following charts are for typical casing programs.
9 5/8 x 7 (32-38 lb) SP 17,500 900 5 8.375 9 5/8" x 53.5 lb/ft. Csg. 5.905 5 7/8
Contact a Dril-Quip representative to obtain strength-and-dimension charts for specific casing programs.
SH Indicates shoulder type hanger SP Indicates split ring type hanger
30 — — 3,800 — — — 26.250 26
30 x 20 SH 5,000 3,800 48 27.250 30 x 1" Wall Pipe 17.553 17 1/2
20 x 13 3/8 SH 10,000 2,400 13 18.510 20" x 133 lb/ft. Csg. 12.490 12 1/4
13 3/8 x 9 5/8 SP 16,500 2,000 10 12.188 133/8" x 72 lb/ft. Csg. 8.803 8 3/4
9 5/8 x 7 (32-38 lb) SP 17,500 700 5 8.375 9 5/8" x 53.5 lb/ ft. Csg. 5.905 5 7/8
SH Indicates shoulder type hanger SP Indicates split ring type hanger
24"" xx 16
30 16" "xx 10
1033//44"" xx 77 55//88"" (or
Casing Program
7 ") Casing Program
INTERNAL
INTERNAL TENSION
TENSION MIN.
MIN. MAX.
MAX.
YIELD
YIELD YIELD
YIELD RETURN
RETURN MAX.
MAX. BIT
BIT
SIZE
SIZE TYPE
TYPE PRESSURE
PRESSURE PRESSURE
PRESSURE AREA
AREA OD
OD HANGER WILL
HANGER WILL MIN. ID
MIN. ID SIZE
SIZE
(inches)
(inches) HANGER
HANGER (psi)
(psi) (x 1,000
(x 1,000 lbs)
lbs) (sq in)
(sq in) (inches)
(inches) RUN THROUGH
RUN THROUGH (inches)
(inches) (inches)
(inches)
24
30 —
— —
— 3,300
3,800 —
— —
— —
— 22.240
26.470 22
26
24 xx 16
30 16 SH
SH 5,000
5,000 3,300
3,300 24
48 21.125
27.530 x 1"/4"Wall
30" 21
1
BOP Pipe 13.802
14.990 1333//44
14
16 1033//44
16 xx 10 SH
SP 12,000
12,000 1,700
1,700 12
12 14.500
14.500 16" xx 109
16" 109 lb/ft.
lb/ft. Csg.
Csg. 9.928
9.928 997//88
7
1033//44 xx 7755//88
10 SP
SP 15,000
15,000 1,200
1,200 66 9.500
9.500 1033//44"" xx 60.7
10 60.7 lb/ft.
lb/ft. Csg.
Csg. 6.802
6.802 663//44
3
SH Indicates
SH Indicates shoulder
shoulder type
type hanger
hanger SP Indicates
SP Indicates split
split ring
ring type
type hanger
hanger
16 9 5/8 x 7 (32-38 lb) SP 17,500 710 5 8.375 9 5/8" x 53.5 lb/ ft. Csg. 5.905 5 7/8
30 x 20 x 13 / x 9 / x 7 SP
"
SH Indicates "shoulder3type
"
Casing Program
5 "
" Indicates split ring type hanger
8 hanger
8
36 — — 5,000 — — — 28.250 28
36 x 24 SH 5,000 5,000 48 29.250 29 /2" BOP
1
22.240 22
24 x 18 /85
SP 7,500 4,500 15 22.000 24 /4" Wall Pipe
3
17.553 17 1/2
18 5/8 x 13 3/8 SP 11,000 3,000 12 17.000 18 5/8" x 136 lb/ft. Csg. 12.490 12 1/4
13 3/8 x 9 5/8 SP 16,500 2,000 10 12.188 13 3/8" x 72 lb/ft. Csg. 8.803 8 3/4
9 5/8 x 7 (32-38 lb) SP 17,500 710 5 8.375 9 5/8" x 53.5 lb/ ft. Csg. 5.905 5 7/8
SH Indicates shoulder type hanger SP Indicates split ring type hanger
36 — — 5,000 — — — 28.250 28
36 x 24 SH 5,000 5,000 48 29.250 29 /2" BOP
1
22.240 22
24 x 18 5/8 SP 7,500 4,500 15 22.000 24 3/4" Wall Pipe 17.553 17 1/2
18 5/8 x 13 3/8 SP 11,000 3,000 12 17.000 18 5/8" x 136 lb/ft. Csg. 12.490 12 1/4
13 3/8 x 9 5/8 SP 16,500 2,000 10 12.188 13 3/8" x 72 lb/ft. Csg. 8.803 8 3/4
9 5/8 x 7 (32-38 lb) SP 17,500 710 5 8.375 9 5/8" x 53.5 lb/ ft. Csg. 5.905 5 7/8
SH Indicates shoulder type hanger SP Indicates split ring type hanger
36 — — 4,500 — — — 28.250 28
36 x 36 SH 3,000 3,700 22 29.250 29 1/2" BOP 24.125 24 17
26 x 20 SP 5,000 3,500 28 24.000 26" x .812" Wall Pipe 17.553 17 /2
1
20 x 13 3/8 SP 10,000 3,000 13 17.446 20" x 1.00" Wall Pipe 12.490 121/4
13 3/8 x 9 5/8 SP 16,500 2,250 13 12.188 13 3/8" x 72 lb/ft. Csg. 8.803 8 3/4
9 5/8 x 7(32-38 lb) SP 17,500 910 5 8.375 9 5/8" x 53.5 lb/ft. Csg. 5.905 5 7/8
DRIL-QUIP WESTERN HEMISPHERE DRIL-QUIP EASTERN HEMISPHERE DRIL-QUIP ASIA PACIFIC
DRIL-QUIP, INC. World Headquarters DRIL-QUIP (Europe), Ltd. DRIL-QUIP Asia Pacific Pte. Ltd.
13550 Hempstead Hwy. Stoneywood Park, Dyce No. 9, Tuas Avenue 12
Houston, Texas 77040 Aberdeen, Scotland, UK AB21 7DZ Singapore, 639031
Tel (713) 939 7711 Tel (44) 1224 727000 Tel (65) 6861 0600
Fax (713) 939 8063 Fax (44) 1224 727070 Fax (65) 6861 5700
DRIL-QUIP do Brasil, LTDA. DRIL-QUIP London DRIL-QUIP China
Macaé, Brazil High Wycombe, Shekou, P. R. China
Bucks, England Tel (86) 75 5268 97137
Tel (55) 22 2791 8950 Tel (44) 1494 601086 Fax (86) 75 5268 97134
Fax (55) 22 2791 8989 Fax (44) 1494 601094
DRIL-QUIP Oilfield Services
DRIL-QUIP New Orleans DRIL-QUIP Norway DRIL-QUIP Egypt (Tianjin) Co., Ltd.
New Orleans, Louisiana Stavanger, Norway Zahraa El-Maadi, Cairo, Egypt Tanggu, Tianjin, P. R. China
Tel (504) 522 5566 Tel (47) 51 443700 Tel (20) 22 753 8809 Tel (86) 22 2580 7466
Fax (504) 522 4426 Fax (47) 51 443701 Fax (20) 22 753 8907 Fax (86) 22 2580 7130
DRIL-QUIP The Netherlands Alexandria, Egypt DRIL-QUIP Malaysia
Beverwijk, The Netherlands Tel (20) 3 450 0507 Kuala Lumpur, Malaysia
Tel (31) 251 22 9250 Fax (20) 3 450 0508 Tel (60) 3 2168 4308
Fax (31) 251 22 0044 Fax (60) 3 2168 4201
DRIL-QUIP Nigeria, Ltd.
DRIL-QUIP Denmark Port Harcourt, Nigeria D.Q. Holdings Pty., Ltd.
Esbjerg, Denmark Tel (234) 84 463866 Perth, Australia
Tel (45) 7518 0944 Fax (234) 84 463649 Tel (61) 8 9322 8600
Fax (45) 7518 0640 Fax (61) 8 9322 8500
DRIL-QUIP (Ghana) Ltd.
Takoradi, Ghana DRIL-QUIP Darwin
Tel: (233) 312 5384 Berrimah, Australia
Tel (61) 420 340 528
Fax (61) 8 8932 8084
DRIL-QUIP Indonesia
Jakarta, Indonesia
Tel (62) 21 720 0612
Fax (62) 21 720 1513