Professional Documents
Culture Documents
FT TH110 en 06-01-2023
FT TH110 en 06-01-2023
TH 110
Humidity and temperature transmitter
Configurable 1 or 2 analogue
outputs 0-10 V
4-20 mA outputs
• Measuring range from 5 to 95 %HR and • ABS V0 housing IP65(2) or IP20(1), with or
from 0 to 50 °C(1) or from -20 to +80 °C(2) without display
• 0-10 V output, active, power supply • Alternating display of humidity and
24 Vac/Vdc (3-4 wires) or 4-20 mA temperature
output, passive loop, power supply from
• “¼ turn” system mounting with wall-
16 to 30 Vdc (2 wires)
mount plate
• Housing with simplified mounting system
Features of housing
46 mm 112 mm 90 mm
80 mm
Protection IP65(2) or IP20(1)
109 mm
109 mm
109 mm
Cable of remote
in FEP (fluorinated ethylene
probes
propylene)
80 mm
Part number
Example: TH 110-ANS
TH 110 A N S Humidity and temperature transmitter
TH 110, 0-10 V active, without display,
Power supply / Output Display Type of probe Probe cable length ambient model.
A: Active 24 Vac/Vdc – 0-10 V O: With display S: Ambient (remote models only)
P: Passive – 16/30 Vdc - 4-20 mA N: Without display A: Duct ( ): 2 m Caution: the TH 110 – POES model
D: Remote 05M: 5 m (passive with display) is not
ES: Standard 10M: 10 m available
(1)
Ambient model / (2) Duct, remote and standard model.
General features
Temperature Humidity
Type of fluid Air and neutral gases Air and neutral gases
*Can be configured by switch.
**All the accuracy indicated in this technical datasheet were stated in laboratory conditions, and can be guaranteed for measurements carried out in the same conditions, or carried out with calibration compensation.
Technical specifications
Screw terminal block for cables from 0.05 to 2.5 mm2 or from 30
Electrical connection
to 14 AWG. Executed following the good practices guidelines.
Simplified calibration
PC Communication USB-mini Din cable
Electronic board and measuring
Environment Air and neutral gases element connected to the front side
of the sensor, which allows to
Conditions of use (°C/%RH/m) From 0 to 50 °C. In non-condensing conditions. From 0 to 2000 m. configure and calibrate your device
without causing any damage.
Operating temperature of the probe From -20 to +80 °C
Connections Inside the front housing Removable front face Fixed back housing
4 5
3
1
(standard model)
- + - + - + - +
1 2 3 4 - 5 - +6 -+7 -+ + 1 2 3 4 - 5 - +6 -+7 -+ +
1 12 23 34 45 56 67 7 1 12 23 34 45 56 67 7
This2connection
hilos must be made by a qualified and trained technician.
To make2 the
hilos
2connection,
hilos the transmitter must not be energized.
For TH 110-AOS, TH 110-ANS, TH 110-AOD, To make a 3-wire connection, BEFORE POWERING UP
TH 100-AND, TH 110-AOA, TH 110-ANA TH 110-ANES, the transmitter, please connect the output ground to
TH 110-AOES models with output 0-10 V - active: the input ground. See drawing below.
VT GND VRH VT GND VRH 3 wires
+ VT- GND VRH- VRH+
VT+GND + VT -GND VRH
VT+GND - VRH+ 3 wires
3 wires
1 2 3 + 4 +- 5 -+ 6 +- 7 -+ + 1 2 3 + + -
4 5 6 +- - +7 - + +
1 12 23 34 45 56 67 7 1 12 23 3 4 54 65 6 7 7
4 wires 3 wires
4 wires
4 wires + 3 wires3 wires
+
Power +
supply 24 Vdc
+ - + - Power Power
supply supply
24 Vdc24 Vdc
+V - -
+V- - + +
- + V
Display/regulator/PLC passive type V V V
- - + + Display/regulator/PLC passive
Display/regulator/PLC type type
passive
Power supply
24Power
Vdc Power
supply supply or
24 Vdc24 Vdc or or + - + - +
+ - + or 1 2 3 + 4 +-5 6+- -+7 - + +
+ or or 1 12 23 3 4 54 65 6 7 7
+- - + + N L
V V
V V
6 7N LN L
Display/regulator/PLC V V
6 76 7 3 wires
passive type
Display/regulator/PLC
Display/regulator/PLC L 3 wires3 wires
passive type type
passive
LPowerLsupply 24 Vdc
N
N L + - + Power Power
supply supply
24 Vdc24 Vdc
N N
N N L L +V +V- - + +
Power supply 24 Vac
4 wires Class Power
II V
Display/regulator/PLC passive VV
type V
Power supply 24 Vac24 Vac
supply
4 wires
4 wires Class IIClass II Display/regulator/PLC passive type type
Display/regulator/PLC passive
For TH 110-POS, TH 110-PNS, TH 110-POD, TH 110-PND, TH 110-POA, TH 110-PNA, TH 110-PNES models with output 4-20 mA - passive:
2 wires
2 wires
2 wires
Settings and use of the transmitter Active switch
It is possible to set the measuring ranges and the unit of the instrument either by 1
switch and/or via software. 2 Output setting
To configure the transmitter, it must not be energized. Then, you can make the 3
settings required, with the DIP switches (as shown on the drawing below). 4 Unit setting
When the transmitter is configured, you can power it up. OffOn
Please follow carefully the combinations beside with the DIP switch. If the combination is wrongly done, the following
message will appear on the display of the transmitter “CONF ERROR”. In that case, you will have to unplug the transmitter,
place the DIP switches correctly, and then power the transmitter up.
Units setting – active switch Outputs setting – active switch
To set a unit of measurement, put the on-off switch 4 of the To set an output, put the on-off switches 1, 2 and 3 of the
FT_EN – TH110 – 06/01/23 – Non-contractual document – We reserve the right to modify the characteristics of our products without prior notice.
units as shown below. measuring ranges as shown below.
Configurations °C °F From 0 to +50 °C From -20 to +80 °C From -50 to +50 °C From 0 to +100 °C
1 1 1 1 1 1
2 2 2 2 2 2
Combinations 3 3 3 3 3 3
4 4 4 4 4 4
It is possible to configure intermediate ranges, an offset... To mount the transmitter, mount the ABS plate on the wall
(drilling: Ø 6 mm, screws and pins are supplied).
Example: for a 0-100 °C transmitter, minimum delta is 20 °C. Insert the transmitter on the fixing plate (see A on the
The instrument can be configured from 0 to +20 °C or from -10 drawing beside). Rotate the housing in clockwise direction
to +10 °C. In order to compensate a possible drift of the sensor, until you hear a “click” which confirms that the transmitter
it is possible to add an offset to the displayed value by the TH is correctly installed.
110 transmitter: it shows 48% RH, a standard instrument shows
Ambient model does not have any mounting
45% RH. It is then possible, via the software, to integrate an offset
plate. 4 fixing holes are present inside the back
of -3 to the displayed value by the TH 110 instrument.
housing. Use them to install the transmitter on the
required location.
The configuration of the parameters can be done either 75 mm
with the DIP switch or via software (you can not combine 37.5 mm
40 mm
both solutions).
23.75 mm
8 mm
A
PC configuration 1 Please refer to the user
50 mm
68 mm
www.sauermanngroup.com