Professional Documents
Culture Documents
Air Motors
Tools
Introduction
Advantages
CP offers a wide range of 1. Compact, with high power to pressure or air flow. No 5. No risk of overheating either
rotating vane type air motors weight ratio. An air motor will expensive control equipment when continuously run or
within a power range of 0.35 hp often be one third or less than is required. frequent stop/starts or
to 0.85 hp. Most motors can be the size of a comparable reversing. Note that this
supplied as single rotation or electric motor. An air motor 3. If a motor is loaded to a condition assumes the use of
reversible. Reversible motors can be used in a portable stalled condition, and held an inline lubrication system.
have keyed shafts, while single application where the weight there for any length of time,
direction motors can be supplied and/or physical size of the no damage is caused to the 6. Reversing motors require
with threaded shafts or electric motor would preclude motor. In certain applications, simple control of air pressure
alternatives. portable operations. For such as tightening fasteners, into ports in the control top of
example, a 0.85 hp air motor one acceptable method of the motor to determine
running at 2000 rpm weighs control is to regulate the air direction of rotation. To
3 lbs and is approximately 8" pressure so that the motor reverse the direction of
long and just over 2" in stalls at the required torque. rotation takes milliseconds to
diameter. complete.
4. When the load is released,
2. The output speed and torque the air motor will reach free 7. Resists moisture, dust, heat.
can be simply controlled by running speed usually within Is generally explosion proof
regulating either the air one third to one half of a and can be used safely in
revolution. most hazardous situations.
Terms
The following terminology is Dynamic torque – the output overcome inertia, it takes more Performance specifications –
used in this publication: torque of the motor at any stage torque to start an air motor than are normally shown with an air
during the operating cycle. The when it is running. Starting inlet pressure of 6.3 bar at the air
No load speed – maximum dynamic torque increases torque is approximately 75% of motor, unless otherwise stated.
speed attained at a given air virtually in a straight line from stall torque. Note that there is approximately
pressure under a no-load zero at no load to a maximum at a 14% drop in power for every
condition. the stalled condition. Air consumption – measured in 10% reduction in air inlet
the no-load condition. Air pressure.
Maximum power – with a vane Stall torque – output torque consumption is maximum at no
type air motor, the maximum achieved when the load applied load, and is approximately three Rotation – non-reversible
power output is achieved at causes the motor to stall. quarters of this figure at maximum motors rotate in a clockwise
nearly one half of the no load power. Air consumption reduces direction if the motor is viewed
speed. This is the point at which Starting torque – to obtain the as the working air pressure is from the air inlet end with the
the motor will run most efficiently. proper sealing of the rotor blades reduced. For example at 50 p.s.i. spindle pointing away from you.
against the cylinder walls for the air consumption is almost
maximum efficiency, and to one half that at 90 p.s.i.
2
LT1317_USA.qxd 27/5/05 11:29 am Page 3
Contents
4 Selecting an Air Motor
5 DM6/DM65 Series
(0.35 hp, Non Reversible, Torque 0 - 5.9 lbf ft)
6 2DM6 Series
(0.35 hp, Reversible, Torque 0 - 5.9 lbf ft)
7 HM Series
(0.60 hp, Non Reversible, Torque 0 - 30 lbf ft)
8 HM55 Series
(0.85 hp, Non Reversible, Torque 0 - 30 lbf ft)
9 2HM5 Series
(0.85 hp, Reversible, Torque 0 - 30 lbf ft)
10 2H410 Series
(0.85 hp, Reversible, Worm Drive)
General Information
• Air Motors are supplied as “Machinery to be incorporated” – Customer is
responsible for safe incorporation into the complete machine.
• Always refer to Operating and Warning instructions supplied with the tool before
operating the tool.
• All accessories and those tools marked with an asterisk (*) are supplied outside the
scope of CP’s ISO9001 registration, but are sourced from firms meeting CP’s
supplier quality assurance requirements.
• Sound levels quoted in this catalogue were obtained from measurements made
according to the EN ISO15744 Test Code. Nominal values are quoted, sound
levels of individual tools may vary by ±3dB(A).
• All dimensions are calculated from metric values.
3
LT1317_USA.qxd 27/5/05 11:29 am Page 4
0.40
0.45
5.2
3.0
1.8
0.9
*
*
*
*
*
*
*
0.33
4.3
2.5
1.5
0.7
0.4
*
*
*
*
*
*
*
0.26
5.9
3.5
2.0
1.2
0.6
0.3
*
*
*
*
*
*
Torque lbf ft
Power hp
0.19
4.4
2.6
1.5
0.9
0.4
0.2
*
*
*
*
*
*
0.13
0.15
4.9
3.0
1.7
1.2
0.6
0.3
*
*
*
*
*
0.06
0.15
0.07
4.3
3.7
2.5
1.5
0.9
0.5
0.3
*
*
*
0
0
0
0
0
0
0
0
0
0
0
0
0
0 2000 4000 6000 8000 10000 12000 14000 16000 18000 16000
0 1100 2200 3300 4400 5500 6600 7700 8800 9900 9000
0 400 800 1300 1800 2300 2700 3200 3600 4000 4200
0 300 600 900 1200 1500 1800 2100 2400 2700 2700
0 180 360 540 720 900 1060 1260 1440 1620 1650
0 110 220 330 440 550 660 770 880 990 980
0 66 130 200 260 330 400 460 530 600 620
0 40 90 130 180 220 260 310 350 400 390
0 30 70 100 130 170 200 230 270 300 290
0 10 20 30 40 50 60 70 80 90 90
0 6 13 20 26 33 40 46 53 60 60
0 5 10 15 20 25 30 35 40 45 45
Speed r/min
4
LT1317_USA.qxd 27/5/05 11:29 am Page 5
MOTOR TYPE
NO LOAD MAX. POWER TORQUE AT AIR CONSUMPTION MIN. HOSE WEIGHT SOUND LEVEL
THREADED SHAFT / KEYED SHAFT / SPEED MAX. POWER AT MAX. POWER BORE
THREADED NOSE THREADED NOSE
r/min. hp lbf ft cfm ins lbs dB(A)
DM65-16000T DM6-16000T 16000 0.17 1.4
DM65-9000T DM6-9000T 9000 0.30 1.4
DM65-4200T DM6-4200T 4200 0.90 1.4
DM65-2700T DM6-2700T 2700 1.33 1.4
DM65-1650T DM6-1650T 1650 2.21 1.6
DM65-980T DM6-980T 980 3.70 1.6
0.35 19.9 3/8 76
DM65-620T DM6-620T 620 5.90 1.6
DM65-390T DM6-390T 390 5.90 1.6
DM65-290T DM6-290T 290 5.90 1.8
DM65-90T DM6-90T 90 5.90 1.8
DM65-60T DM6-60T 60 5.90 1.8
DM65-45T DM6-45T 45 5.90 2.0
0.40
0.45
5.2
3.0
1.8
0.9
*
*
*
*
*
*
*
To 0.33
rq ue
4.3
2.5
1.5
0.7
0.4
*
*
*
*
*
*
*
6b Power
ar
(87
ps 0.26
i)
5.9
3.5
2.0
1.2
0.6
0.3
*
*
*
*
*
*
Torque lbf ft
Power hp
4b 0.19
ar
4.4
2.6
1.5
0.9
0.4
0.2
*
*
*
*
*
*
(58
psi
)
0.13
0.15
4.9
3.0
1.7
1.2
0.6
0.3
*
*
*
*
*
2 ba
r (24 0.06
psi)
0.15
0.07
4.3
3.7
2.5
1.5
0.9
0.5
0.3
*
*
*
0
0
0
0
0
0
0
0
0
0
0
0
0
0 2000 4000 6000 8000 10000 12000 14000 16000 18000 16000
0 1100 2200 3300 4400 5500 6600 7700 8800 9900 9000
0 400 800 1300 1800 2300 2700 3200 3600 4000 4200
0 300 600 900 1200 1500 1800 2100 2400 2700 2700
0 180 360 540 720 900 1060 1260 1440 1620 1650
0 110 220 330 440 550 660 770 880 990 980
0 66 130 200 260 330 400 460 530 600 620
0 40 90 130 180 220 260 310 350 400 390
0 30 70 100 130 170 200 230 270 300 290
0 10 20 30 40 50 60 70 80 90 90
0 6 13 20 26 33 40 46 53 60 60
0 5 10 15 20 25 30 35 40 45 45
Speed r/min
DM6-T
Max Loading Exhaust Collector can be mounted with silencer facing in
123 lbf either direction and rotated through 360° - 1/4" BSP thread.
1/8" BSP
Air inlet
0.472
Ø10(h6)
0.276
M35 x 1.0 L.H.
1.772
Ø1.417
0.047
0.118 Optional
0.512 Adaptor
for
0.925 1/8" NPT
1.594 Air Inlet
Tapped hole M4 x 13 0.118 0.551
A 1.496 Ø1.496
0.276
DM65-T
M35 x 1.0 L.H.
SPEED A
5
LT1317_USA.qxd 27/5/05 11:29 am Page 6
2DM6 Series
2DM6 Series
0.35 hp,
Maximum Torque 5.9 lbf ft,
Reversible
MOTOR TYPE NO LOAD SPEED MAX. POWER TORQUE AT1) AIR CONSUMPTION MIN. HOSE WEIGHT SOUND
MAX. POWER AT MAX. POWER BORE
1)
It is recommended that a suitable air diffuser is fitted downstream of any control valve through which exhaust air exits.
0.40
0.45
5.2
3.0
1.8
0.9
*
*
*
*
*
*
*
To 0.33
4.3
2.5
1.5
0.7
0.4
*
*
*
*
*
*
*
rq
6 b ue
ar
(87
0.26
ps
5.9
3.5
2.0
1.2
0.6
0.3
i)
*
*
*
*
*
*
Torque lbf ft
Power
Power hp
0.19
4.4
2.6
1.5
0.9
0.4
0.2
4b
*
*
*
*
*
*
ar (
58p
si)
0.13
0.15
4.9
3.0
1.7
1.2
0.6
0.3
*
*
*
*
*
2 bar (2
0.06
9psi)
0.15
0.07
4.3
3.7
2.5
1.5
0.9
0.5
0.3
*
*
*
0
0
0
0
0
0
0
0
0
0
0
0
0
0 2000 4000 6000 8000 10000 12000 14000 16000 18000 16000
0 1100 2200 3300 4400 5500 6600 7700 8800 9900 9000
0 400 800 1300 1800 2300 2700 3200 3600 4000 4200
0 300 600 900 1200 1500 1800 2100 2400 2700 2700
0 180 360 540 720 900 1060 1260 1440 1620 1650
0 110 220 330 440 550 660 770 880 990 980
0 66 130 200 260 330 400 460 530 600 620
0 40 90 130 180 220 260 310 350 400 390
0 30 70 100 130 170 200 230 270 300 290
0 10 20 30 40 50 60 70 80 90 90
0 6 13 20 26 33 40 46 53 60 60
0 5 10 15 20 25 30 35 40 45 45
Speed r/min
Air Inlet
Forward
0.354
1.890CRS
2.362
Ø37
(f7)(1) Ø1.417
SPEED A
0.965 0.551
6
LT1317_USA.qxd 27/5/05 11:29 am Page 7
HM Series
HM Series
0.6 hp,
Maximum Torque 30 lbf ft,
Non Reversible
MOTOR TYPE NO LOAD SPEED MAX. POWER TORQUE AT AIR CONSUMPTION MIN. HOSE WEIGHT SOUND
MAX. POWER AT MAX. POWER BORE
0.67
To
23.9
14.8
6.4
4.3
2.7
rqu
*
*
*
Power
e
6b
ar
(87
ps 0.54
28.6
19.1
11.8
5.1
3.4
2.1
i)
*
*
Torque lbf ft
Power hp
0.40
21.5
14.3
8.9
3.9
2.6
1.6
*
*
4b
ar
(58
psi
0.26
)
14.3
9.6
5.9
2.6
1.7
1.1
*
*
2b
0.13
ar (
29p
27.6
7.2
4.8
3.0
1.3
0.9
0.5
si)
*
0
0
0
0
0
0
0
0
0
Speed r/min
Ø0.354 0.610
0.500
0.374 Air inlet 1/4" BSP
(1/4" NPT optional)
11/2" X 20 TPI LH
Ø 49.2 (f7)(1)
2.756 CRS
3.50
HM-4600 HM-2850
Ø 1.87
Ø 2.44
HM-1900
11/2" X 20 UNF
0.394
2.20 1.04
2.00 0.354 0.551
0.189
Ø0.354 0551
0.630 Exhaust
0.354
15/8" X 16 TPI LH
Ø 49.2 (f7)(1)
HM-830
2.756 CRS
HM-500
Ø 2.44
3.50
Ø 1.87
HM-340
HM-90
HM-60
5/8" X 16 UN
0.394
2.20 1.04
0.551
SPEED A
0.374
2.00 0.189
7
LT1317_USA.qxd 27/5/05 11:29 am Page 8
HM55 Series
HM 55 Series
0.85 hp,
Maximum Torque 30 lbf ft,
Non Reversible
THREADED SHAFT NO LOAD SPEED MAX. POWER TORQUE AT AIR CONSUMPTION MIN. HOSE WEIGHT SOUND
MAX. POWER AT MAX. POWER BORE
0.94
20.7
9.0
6.0
1.0
*
*
*
*
*
0.80
To
28.7
17.7
Power
7.7
5.1
0.9
rq
*
*
*
*
ue
6b
ar
(87 0.67
ps
23.9
14.8
6.4
4.3
0.7
i)
*
*
*
*
0.54
Torque lbf ft
28.6
19.1
11.8
5.1
3.4
0.6
Power hp
*
*
*
4b
ar
(58 0.40
psi
21.5
14.3
8.9
3.9
2.6
0.4
)
*
*
*
0.26
14.3
9.6
5.9
2.6
1.7
0.3
*
*
*
2b
ar (
29p 0.13
si)
27.6
17.0
0.15
7.2
4.8
3.0
1.3
0.9
*
0
0
0
0
0
0
0
0
0
0
0 2000 4000 6000 8000 10000 12000 14000 16000 18000 18000
0 345 690 1034 1379 1724 2069 2414 2759 3103 3300
0 230 460 690 920 1149 1379 1609 1839 2069 2100
0 100 200 300 400 500 600 700 800 900 950
0 62 123 185 247 309 370 432 494 556 550
0 41 82 124 165 206 247 289 330 371 350
0 17 35 52 70 87 104 122 139 157 150
0 11 21 32 43 53 64 75 86 96 100
0 5 10 14 19 24 29 33 38 43 40
Speed r/min
Ø40(h6)(1)
Ø53(f8)(1)
Ø2.047
Ø1.00
0.177
0.846 A/F
0.177 0.394
Ø2.125 0.185
8
LT1317_USA.qxd 27/5/05 11:29 am Page 9
2HM5 Series
2HM5 Series
0.85 hp,
Maximum Torque 30 lbf ft,
Reversible
MOTOR TYPE NO LOAD SPEED MAX. POWER TORQUE AT AIR CONSUMPTION MIN. HOSE WEIGHT SOUND
MAX. POWER AT MAX. POWER BORE
0.94
20.7
9.0
6.0
1.0
*
*
*
*
*
To
0.80
rq
28.7
17.7
ue
7.7
5.1
0.9
Power
*
*
*
*
6b
ar
(8
7p
0.67
si)
23.9
14.8
6.4
4.3
0.7
*
*
*
*
0.54
Torque lbf ft
28.6
19.1
11.8
5.1
3.4
0.6
Power hp
*
*
*
4b
ar
(58 0.40
21.5
14.3
8.9
3.9
2.6
0.4
psi
*
*
*
0.26
14.3
9.6
5.9
2.6
1.7
0.3
*
*
*
2b
ar (
29p
0.13
s i)
27.6
17.0
0.15
7.2
4.8
3.0
1.3
0.9
*
0
0
0
0
0
0
0
0
0
0
0 2000 4000 6000 8000 10000 12000 14000 16000 18000 18000
0 345 690 1034 1379 1724 2069 2414 2759 3103 3300
0 230 460 690 920 1149 1379 1609 1839 2069 2100
0 100 200 300 400 500 600 700 800 900 950
0 62 123 185 247 309 370 432 494 556 550
0 41 82 124 165 206 247 289 330 371 350
0 17 35 52 70 87 104 122 139 157 150
0 11 21 32 43 53 64 75 86 96 100
0 5 10 14 19 24 29 33 38 43 40
Speed r/min
Ø2.125
Ø0.354 1.18
Forward
Ø53 (f8)(1)
Ø40 (h6)
Ø2.047
3.543
Ø0.669
Reverse
0.185
35
A
0.512 CRS
18000
0.315
9
LT1317_USA.qxd 27/5/05 11:29 am Page 10
2H410 Series
2H410 Series
0.85 hp,
Maximum Torque 78 lbf ft,
Worm Drive Motors
MOTOR TYPE NO LOAD SPEED MAX. POWER MAX. STALL MIN. SAFE WORKING MAX. AIR MIN. HOSE WEIGHT SOUND
TORQUE PRESSURE CONSUMPTION BORE
A
2.69 0.85 0.71
B
Note: Exhaust is through common exhaust Ø 2.051 Exhaust Port
port and opposite rotation inlet port.
3/8"BSP
1.03
2.051
Reverse Port
0.374 Forward Port 1/4"BSP
527" A/F Interna Hexagon Thro
Ø 2.00 1/4"BSP
1.21
Left Hand Right Hand
Rotation Rotation
Ø 2.03
This Side This Side
TYPE SPEED A B
10
LT1317_USA.qxd 27/5/05 11:29 am Page 11
Selection Questionnaire
The following questionnaire is for use either by the engineer for his/her own calculations or can
be completed and returned to the local CP Sales Office.
Specification
Rotation Forward 6
Reverse 6
Reversible 6
11
LT1317_USA.qxd 27/5/05 11:29 am Page 12
Output Accessories
Key Adjustable Chucks
MOTOR TYPE CHUCK CAPACITY CHUCK AND KEY
ins part no.
DM65-T 1/4 28942
5/16 94502
3/8 31132
HM-1900-4600
1/2 29142
HM55-2100-18000
HM-60-830
1/2 29122
HM55-40-950
Collet Chucks
COLLETS
ins part no. ins part no. ins part no. ins part no.
0.031 2892 0.075 3002 0.118 3112 0.161 3222
0.035 2902 0.079 3012 0.122 3122 0.165 3232
0.039 2912 0.083 3022 0.126 3132 0.169 3242
0.043 2922 0.087 3032 0.130 3142 0.173 3252
0.047 2932 0.091 3042 0.134 3152 0.177 3262
0.051 2942 0.094 3052 0.138 3162 0.181 3272
0.055 2952 0.098 3062 0.142 3172 0.185 3282
0.059 2962 0.102 3072 0.146 3182 0.189 3292
0.063 2972 0.106 3082 0.150 3192 0.193 3302
0.067 2982 0.110 3092 0.154 3202 0.197 3312
0.071 2992 0.114 3102 0.157 3212
Thread Adaptor
MOTOR TYPE A B
part no.
A DM65-T 3/8" x 24 UNF 1/2" x 20 UN 68143
12
LT1317_USA.qxd 27/5/05 11:29 am Page 13
Output Accessories
Flange for DM6/65-T
R0.315 2 HOLES Ø0.276 2 HOLES Ø0.276 R0.315 2 HOLES Ø0.276 R0.236 2 HOLES Ø0.276 R0.315
2.00
2.25
2.25
1.890
1.752
1.752 Ø1.50 1.752
0.787
Part No. Part No. Part No. Part No.
0.787 0.630 0.280
0.669
390693 390683 441653 286423
0.669 0.161
0.512 0.177 0.216
0.512
M35x1.OP LH 6H
M35x1.OP LH 6H
Ø34.90(1)
Ø41.224(1)
M35 -1.O LH 6H
M35 -1.O LH 6H
Ø41.22(1)
Ø28.98(1)
Ø1.457
Ø1.457
Ø41.275
Ø34.85
Ø1.457
Ø41.28
Ø28.96
2.88
390683/390693 – 0.591
441653 – 0.748
0.295
0.315 0.315 0.09
Part No. 390683 provides same mounting dimensions as DM – 17700/5300/4000/3000/1600
Part No. 390693 provides same mounting dimensions as DM – 900/500/210/80/40
Part No. 441653 provides same mounting dimensions as DM6 and DM65 motors
(1)
Dimensions in mm
Stands
R55 Lever Operated Stand for HM Series
Note: Motor must be fitted with exhaust
collector ring (see above)
8.00
1.25"
17.83
8.00 9.25
5.00
1.65 0.50
13
LT1317_USA.qxd 27/5/05 11:29 am Page 14
11.42
1.50
24.00 approx.
2.30
Height
Adjustment
15.95 Self-
10.04 Start Mounting
plunger Plate
Stroke Height
Adjustment Adjustment
3.00 Stroke
12.68
1.50 Adjustment
Max. 2.87
approx
7.00
1.00
1.65
3.94
0.50
14.96 Standard
9.06 Optional 40.98
approx.
1.97
Self-
9.84 Start Mounting 9.84
plunger Plate
Height 40.16
Adjustment
3.54 7.00
Max Stroke
7.00 29.25 Adjustment
approx. 25.43
Max
1.57 approx. 1.57
2.00
2.00
14.09
14.09
Ø1.18
Ø1.18
12.28
12.28
12.00 4.02 13.19
12.00 4.02 13.19
6.18 0 0.50
6.18 0.50
14
LT1317_USA.qxd 27/5/05 11:29 am Page 15
Control Equipment
Operating the Motor A Typical Control Circuit
To obtain the longest life
span of the vane type air
motor, it is recommended Reversible
in sufficient quantity is
Valve Forward Port
all times.
Controlling the motor can be
achieved using pneumatic
valves, either hand, foot, pilot
air or solenoid operated. The
Exhaust Port
motor.
Lubricator
Torque is controlled by
Air Supply
15
LT1317_USA.qxd 27/5/05 11:29 am Page 16
www.cp.com
USA LT1317SSDGeccc555
Printed in England May 2005 Issue 1 Certificate No. FM28383 Certificate No. EMS61525
© Copyright 2005 Desoutter Limited Desoutter Limited
CP G. Renault Nantes France ISO 9001 Registered ISO 14001 Registered