Professional Documents
Culture Documents
Oil Pan For 785 (8GB); 785B (6HK); 789 (9ZC); 789B (7EK); 793 (3SJ);
793B (1HL); 994 (9YF) - Sealant replaces a gasket in oil pan groups -
1U8836 or 4C5300 sealant replaces 7E2633 gasket - Service Literature:
Service Magazine November 1, 1993
Liquid For MHI - Gasket part numbers that are discontinued - see 'L' section
Spark Plug - for G398 low emission, G399 low emission, 3512, 3516
spark ignited engines - 9Y6792 -Service Magazine November 27, 1989
Head - New Gasket Used On All 3208 Engines. -Service Magazine May 15, 1989
Exhaust Manifold - 7C0710 for 3116 use 2W7204 - See TIB February 28, 1990
Air Compressor Group - Example 2P8709 - fits between the lines and
head assembly was round with a lip now redesigned to football shaped.
This is part of 7N2834 kit but not shown in print.
For Hydraulic Pump Group For 55 Winch D5 25X - 3P1605 gasket goes
with 3P5918 pump group
Gasket Kits
D379B 76B1-415 - Complete kit not available - See TPG for valve
grinding list
Not Shown In Fiche - Original - 4S7720 (for 768B 79S); Use 6V2349 (one
too many 5H2831 inside)
Gauge
627-15S - Round sight gauge in Case & frame - Diff 5T5203 - Trans.
5T5204 - Gasket 5T7100
3208 New Oil Gauges - Not available - engine oil refill capacity reduced.
Service Literature: Service Magazine November 1, 1987
627 - 15S - New round site in case and frame diff: 5T5203 - trans: 5T5204
- gasket: 5T7100; Old one oblong
Argon Filled Gauges - Service Literature: Service Magazine October 26, 1981
8M4888 Trans Temp Gauge (Not Needed) - CRB 2 plugs and 1 button
Oil Level Sight (Hyd & Tran Oil Tanks) For Trucks - Service Literature:
Service Magazine September 25, 1989
MANY TIMES YOU WILL SEE A GAUGE THAT HAS A SCREW IN SOCKET WITH
A BULB. IN MOST CASES THE BULB IS CALLED OUT USUALLY AS A 115-
1738, 24VOLT LAMP BUT THE SOCKET IS NEVER SHOWN. FOR CASES
LIKE THIS YOU MAY USE a 5I8306 BULB AS. USED ON 300 SERIES
EXCAVATORS, INTERGRATEDTOOLCARRIERS. LOOK AT PRINTS OF
5I8306 AND 1104731 AS EXAMPLES.
Gear Assembly
7L2388 Replaced By 1-7L2389 Gear & 1-7L2387 Bearing. They will have to ream
the bearing to 1.3760 + or - .0005 until the gear assembly is set backup.
Generators
MHI Engines (6D14CT) - This Note Applies To All 6D1 Engines 1/19/95 -
There are none! per Service Eng. - 11/5/92 if the customer has glow
plugs, they have either replaced the original engine or they are giving us
the wrong information.
Dummy - 4N4122
Precombustion Chamber Plugs - For glow plug hole 4N4122 short 7L2123
Glue
Governor - Caps
Governor - Control
Convert From Single Lever To Two Levels -Service Magazine April 4, 1988
Governor Cover
Woodward Governor Parts That Are Not Serviced By CAT - Dealer can
call Hatch and Kirk (Woodward Distributor) (800)445-4672, Jill Kelly
Governor Group
Grab Irons
Special Purpose Grease Dash Sheet - IRM FLU 90-6 March 5, 1990
9C2573 P/O 3V5261 Boom Arr. - left out of parts book - 225B 2ZD1 up
966-992 & 225-245 - Heavy duty long life tips - IRM GET 93-5
D10 & D11 SU & U Dozers - DH-3 cutting edges - IRM GET 93-9
IRM Listing - Complete listing of GET related IRMs which have been
issued from 1980-1986 - IRM GET 88-6 February 24, 1988 (1983 -
1987) replaces - IRM Get 87-1 February 13, 1987
Sharp Tips For Excavator Buckets - IRM GET 87-5 February 16, 1987
D11N Intermediate Center Line Ripper Tip - IRM GET 87-5 August 10,
1987
Abrasive-Resistant Bolt On Edge 950B & 966D - IRM GET 87-14 April
15, 1987
New Buckets For 225B & 229 Exc. - IRM GET 87-21 June 12, 1987
Bolt On Edge For 988 Straight Edge Rock Bucket - IRM GET 87-22 June
22, 1987
Push Plates & Wear Plates For 'N' Series Dozer D11N, D10N, D9N &
D8N - IRM GET 87-26 July 31, 1987
Sharp Tips For E180 & 215 Buckets - IRM GET 87-32 November 13,
1987
New Buckets For 235 Excavators - IRM GET 87-35 December 11, 1987
New Bucket Tip For MHI & Esco 35 Series Conical Adapters - IRM GET
87-29 December 23, 1987 - IRM GET 88-9 February 22, 1988 - bucket
tips for MHI & Esco 30 series
'E' Series Wheel Loaders - IRM GET 88-2 January 18, 1988
651E & 657E Scrapers Cutting Edges - IRM GET 88-8 February 29, 1988
Komatsu D155/D315 - Dozer cutting edges and end bits - GET 92-8
August 1992
330 Bucket - Boom, stick and bucket information - IRM GET 92-14
October 1992
320 Bucket - Boom, stick, and bucket information - IRM GET 92-13
October 1992
992 & 994 Bucket Tip Options - IRM GET 93-2 January 1993
994 Wheel Loader New Buckets & G.E.T - IRM GET 93-3 March 1993
416B, 426B, & 436B G.P. Loader Buckets - Factory installed cutting edge
is now available - Model Bucket Ref. No. - 416B 1.00 yd 9R5321 - 426B
1.25 yd 9R5321 - 436B 1.38 yd 9R5321
518 Harvester - Must be ordered by the dealer direct from: The Egging
Company Gurley, Nebraska 69141 Attn: Sonja Vallier or Tom Frerichs
Phone (308)884-2233 Telex: 287578 - Service Literature: Service
Magazine December 22, 1986
D8K Radiator - 9P2909 (2 hinges;1 Pin) for lower plate 6P2493 use 7G0916. Only
difference is small notch .75 x 2.50 cut in 7G0916 at top right corner of plate.
7G0961 used in guard assembly 6P2495 (3 hinge pins)
Guards
245 Skylight Guard - 2V8445 Service Parts --Found in front shovel --
ARR. in 245D book S/N 7ZJ1-up - Page 309, Ser.# 82X651-up
973 & 973 LGP - thicker bottom guards see Service Magazine May 14, 1984
Spray Guards For 950, 960, 966, & 970F's - See Mud flaps
Stabilize Guards To Prevent Boom Cyl Damage For 416 & 426 - 9R3280
Guard group Service Literature: Service Magazine November 2, 1987 -
also SEHS8710 for installation
Alt. Belt Guard For D11N, 776B Tractor, 777B, 785 & 789 Trucks -
Service Literature: Service Magazine June 1, 1987
Bottom For 225 - To cover engine and radiator. See 227 page 105. Mod.
may be necessary
Thicker Bottom For 973 & 973 LGP - Service Literature: Service
Magazine May 14, 1984
Front & Rear Track Roller Frames D6H - Service Literature: Service
Magazine March 5, 1990
Last Update:
02/01/05
wcg