Professional Documents
Culture Documents
Maintenance
Accessories
3
Air Line
Filters, Regulators,
& Lubricators 4 Hoses & Fittings
23 Couplers & Plugs
28
Ergonomic
Spring Balancers
124 Torque Reaction
Arms 129 Grips & Braces
133
Maintenance
Lubricants &
Grease Guns 135
ingersollproducts.com/accessories
4
Selections
Filters, Regulators,
& Lubricators
When
Sets selecting an FRL or individual filter, regulator, and lubricator units, the air consumption of the tools
or equipment to be serviced should be correlated with the flow capacity of the FRL. ARO Filters, Regulators,
and Lubricators are designed to flow in excess of that indicated in the maximum recommended flow table
shown below. This table gives recommended flows for pipe sizes at listed pressures and should be used as
a guide in sizing piping and equipment for compressed air systems.
Maximum recommended air flow (scfm) thru ANSI standard weight Schedule 40 pipe
Applied Nominal Standard Pipe Size — Inches
Pressure
PSIG 1/8" 1/4" 3/8" 1/2" 3/4" 1" 1-1/4" 1-1/2" 2" 2-1/2" 3"
5 0.5 1.2 2.7 4.9 6.6 13 27 40 80 135 240
10 0.8 1.7 3.9 7.7 11.0 21 44 64 125 200 370
20 1.3 3.0 6.6 13.0 18.5 35 75 110 215 350 600
40 2.5 5.5 12.0 23.0 34.0 62 135 200 385 640 1100
60 3.5 8.0 18.0 34.0 50.0 93 195 290 560 900 1600
80 4.7 10.5 23.0 44.0 65.0 120 255 380 720 1200 2100
100 5.8 13.0 29.0 54.0 80.0 150 315 470 900 1450 2600
150 8.6 20.0 41.0 80.0 115 220 460 680 1350 2200 3900
200 11.5 26.0 58.0 108.0 155.0 290 620 910 1750 2800 5000
250 14.5 33.0 73.0 135.0 200 370 770 1150 2200 3500 6100
The flow values in the chart above are based upon a pressure drop ( ΔP) as set forth in the following schedule:
Pressure Drop (ΔP) per 100 ft. of Pipe Pipe Size — Inches
10% of Applied Pressure 1/8, 1/4, 3/8, 1/2
5% of Applied Pressure 3/4, 1, 1-1/4, 1-1/2, 2, 2-1/2, 3
Installation
The filter, regulator, and lubricator
should be installed in the order shown
in the illustration below. If a coalescing
filter is required, it should be installed
downstream from a standard filter.
Individual take-off lines to the FRL and Compressed Air
air tool or equipment should be from Filter Regulator Lubricator
Shut-off
the top of the compressed air line. Make valve
Filters
Filters, Regulators,
& Lubricators
*Inlet pressure 90 psi (6.2 bar) with 10 psi drop (0.7 bar)
7
Filters, Regulators,
& Lubricators
Technical Data
Regulators
Filters, Regulators,
& Lubricators
*Inlet pressure 100 psi (6.9 bar), 90 psi (6.2 bar), with 33 psi (2.3 bar) drop.
9
Adjustment range can exceed spring rating on 0 – 30 psi and 0 – 60 psi regulators. The
Filters, Regulators,
working range of the adjustment knob is designed to permit outlet pressures beyond the spring
& Lubricators
ratings in the 0 – 30 psi and 0 – 60 psi models. The adjustment knob is not designed to be a
pressure limiting device. Limiting devices may be obtained only by special design. For optimal
performance, regulators should not be set to ranges outside the specified spring range.
Technical Data
Lubricators
Filters, Regulators,
& Lubricators
*Inlet pressure 90 psi (6.2 bar) with 7 psi (0.5 bar) drop.
11
Filters, Regulators,
& Lubricators
Technical Data
*Inlet pressure 100 psi (6.9 bar), 90 psi (6.2 bar), with 33 psi (2.3 bar) drop.
13
Adjustment range can exceed spring rating on 0 – 30 psi and 0 – 60 psi regulators. The
Filters, Regulators,
working range of the adjustment knob is designed to permit outlet pressures beyond the spring
ratings in the 0 – 30 psi and 0 – 60 psi models. The adjustment knob is not designed to be a
& Lubricators
pressure limiting device. Limiting devices may be obtained only by special design. For optimal
performance, regulators should not be set to ranges outside the specified spring range.
Technical Data
2-Piece Combinations
Filters, Regulators,
& Lubricators
manual drain • polycarbonate bowls • relieving • W/ gauge 3/8" P39234-610 L36231-110 71 C38231-610
1/8" P39114-600 L36111-100 36 C38111-600 manual drain • Polycarbonate Bowls w/ guard • relieving •
W/ gauge
1/4" P39124-600 L36121-100 44 C38121-600
1/4" P39224-600 L36221-100 58 C38221-600
Auto drain • metal bowl • relieving • W/ gauge
3/8" P39234-600 L36231-100 71 C38231-600
1/4" P39124-624 L36121-120 44 C38121-621
Auto drain • Metal Bowls w/ sight glass • relieving • W/ gauge
Auto drain • polycarbonate bowl • relieving • W/ gauge
1/4" P39224-614 L36221-110 58 C38221-611
1/4" P39124-604 L36121-100 44 C38121-601
3/8" P39234-614 L36231-110 71 C38231-611
Auto drain • Polycarbonate Bowls w/ guard • relieving •
W/ gauge
1/4" P39224-604 L36221-100 58 C38221-601
3/8" P39234-604 L36231-100 71 C38231-601
*Inlet pressure 100 psi (6.9 bar), 90 psi (6.2 bar), with 33 psi (2.3 bar) drop.
15
Filters, Regulators,
& Lubricators
Technical Data
3-Piece Combinations
Filters, Regulators,
& Lubricators
*Inlet pressure 100 psi (6.9 bar), 90 psi (6.2 bar), with 33 psi (2.3 bar) drop.
17
Filters, Regulators,
& Lubricators
Technical Data
Technical Data
Bowl
Size Model
NPT cfm* oz lb
inline lubricators
1/4" 36 0.25 0.2 L01-02-000
3/8" 38.1 0.25 0.2 L01-03-000
3/4" 45 5 1.5 6LUB12
3/4" 80 8 2 8LUB12
Liquidator Filters ™
Filters, Regulators,
Pressure differential
& Lubricators
gauge: Green when new;
changes to red when
element needs replaced
1/4 " • 3/8" • 1/2" • 3/4" Ports
Centrifugal spinning
You can depend on Ingersoll Rand Liquidator™ filters to
deliver clean, dry air to all of your operations. Liquidator filters Friction drying and
filtered air to 1 micron
are designed to extract large volumes of liquid contaminants,
foreign particles, and condensation in air lines. They are ideal
for critical applications in paint and body shops, food processing Stainless steel media:
and packaging, hospital and dental equipment, process controls, Filtration to 3 microns
with greater than 99.9%
printing plants, electronics clean rooms, sandblasting, and air efficiency
tool operations.
Inverse-flow
Model Description
NPT cfm
Stacked Liquidators w/ Polycarbonate Bowls
8842-W1-020 1/4" Stacked Liquidator, indicator, & automatic drain 20 8844-W1-035 8844-W1-M60
Accessories
Filters, Regulators,
& Lubricators
Filters, Regulators,
& Lubricators
T-bracket C-bracket
T-brackets provide an excellent solution for C-brackets are designed to hold either a
wall-mounting your FRL unit. They can be used single filter or single lubricator unit. The
for single or combination configurations in the bracket has two holes to allow for the unit
modular arrangement. T-type brackets give good to be bolted to a wall or other flat surface.
wall-to-unit clearance for installing fittings or Mounting hardware not included.
other connections. Kit includes bracket, modular
clamp, and bolt(s). Model Number Size Material Description
104407 1000 Series
Model Number Size Material Description 104408 1500 Series C-type
Steel
104399 1000 Series Nylon 104409* 2000 Series wall bracket
104400 1500 Series Nylon 104410 3000 Series
T-type wall mounts
104401 2000 Series Aluminum *Does not fit 3/4" NPT filter
104402 3000 Series Aluminum
Model Number Size Material Description Model Number Size Material Description
104394 1000 Series Nylon 104403 1000 Series
104395 1500 Series Aluminum Modular / clamp 104404 1500 Series L-type
Steel
104396 2000 Series Aluminum & zinc spacer kit 104405 2000 Series wall bracket
104397 3000 Series Aluminum 104406 3000 Series
Panel nut
The panel nut allows the user to attach
the regulator or piggyback unit to a panel
or L-bracket. Panel nuts are included as
standard on all ARO-Flo Series regulators
and piggybacks.
Accessories
Filters, Regulators,
& Lubricators
Add-on gauges
Gauges & port blocks Model Port Range (psi) Size Case Lens
104491 1/8" 0 – 45 1.5" Plastic Polycarbonate
In the absence of the standard integral
104488 1/8" 0 – 45 1.5" Steel Glass
gauge, a gauge port block can be used
104498 1/8" 0 – 45 2" Plastic Polycarbonate
with a screw-in aftermarket gauge. All
104494 1/8" 0 – 45 2" Steel Glass
regulators, piggybacks, and combo units
104492 1/8" 0 – 75 1.5" Plastic Polycarbonate
ordered without a gauge will come with
104489 1/8" 0 – 75 1.5" Steel Glass
a gauge port block supplied as standard.
104499 1/8" 0 – 75 2" Plastic Polycarbonate
All port blocks are 1/8" NPT.
104495 1/8" 0 – 75 2" Steel Glass
104493 1/8" 0 – 160 1.5" Plastic Polycarbonate
Model Number Size Material Description
104490 1/8" 0 – 160 1.5" Steel Glass
104467 1000 / 1500 Series 104500 1/8" 0 – 160 2" Plastic Polycarbonate
Gauge port block
104469 2000 / 3000 Series Body: nylon 104496 1/8" 0 – 160 2" Steel Glass
Thread: steel
104310 1000 / 1500 Series Flush-mount 104504 1/4" 0 – 160 2" Plastic Polycarbonate
Lens: poly
gauge
104334 2000 / 3000 Series 104502 1/4" 0 – 160 2" Steel Glass
(0 – 140 psi)
104501 1/8" 0 – 250 2" Plastic Polycarbonate
104497 1/8" 0 – 250 2" Steel Glass
104505 1/4" 0 – 250 2" Plastic Polycarbonate
104503 1/4" 0 – 250 2" Steel Glass
23
Ø
Ø
Model
in ft
38016820 3/8' 50'
Bulk Hose
Ø Ø
Model Description
in psig
50923 1/4" 1 braid rayon 250
BH6C 3/8" 1 braid rayon 250
BH8A 1/2" 1 braid rayon 250
BH12A 3/4" 1 braid rayon 200
Whip Hoses
Ø
Ø Ø Ø Ø
Model
Male NPT Female NPT in ft psig
R00H-130 1/8" 1/4" 1/4" 8' 250
R0-130 1/4" 3/8" 5/16" 8' 250
R1A-130 1/4" 3/8" 3/8" 8' 250
510-130 3/8" 3/8" 3/8" 8' 250
Features
NPT in in in ft ft
• Permanently coiled hoses automatically
return to their original position, keeping swivel COUPLING AT ONE END
them off the floor and out of your way as N14-12A 1/4" 1/4" 3-1/2" 6" 10' 12'
you work N14-25A 1/4" 1/4" 3-1/2" 10-1/2" 22' 25'
• Made from abrasive-resistant and N14-50A 1/4" 1/4" 3-1/2" 21" 45' 50'
memory-resilient Nylon II N38-12A 3/8" 3/8" 5-5/8" 5" 10' 12'
• For use with air, gases, water, and liquids N38-25A 3/8" 3/8" 5-5/8" 10-1/4" 21' 25'
compatible with Nylon II N38-50A 3/8" 3/8" 5-5/8" 21" 44' 50'
• Certified to a maximum pressure of 200 psi N12-12A 1/2" 1/2" 9" 5" 9' 12'
• Fittings and hose ends are protected by N12-25A 1/2" 1/2" 9" 9" 18' 25'
spring guards N12-50A 1/2" 1/2" 9" 19" 41' 50'
• Available with diameters of 1/4", 3/8", swivel COUPLING AT BOTH ENDS
1/2", and 3/4" N14-12B 1/4" 1/4" 3-1/2" 6" 10' 12'
• Available in bulk lengths of 12', 25', 50', N14-25B 1/4" 1/4" 3-1/2" 10-1/2" 22' 25'
and 100' N14-50B 1/4" 1/4" 3-1/2" 21" 45' 50'
N38-124B 1/4" 3/8" 5-5/8" 5" 10' 12'
N38-254B 1/4" 3/8" 5-5/8" 10-1/4" 21' 25'
N38-504B 1/4" 3/8" 5-5/8" 21" 44' 50'
N38-12B 3/8" 3/8" 5-5/8" 5" 10' 12'
N38-25B 3/8" 3/8" 5-5/8" 10-1/4" 21' 25'
N38-50B 3/8" 3/8" 5-5/8" 21" 44' 50'
N12-12B 1/2" 1/2" 9" 5" 9' 12'
N12-25B 1/2" 1/2" 9" 9" 18' 25'
N12-50B 1/2" 1/2" 9" 18" 41' 50'
N34-12B 3/4" 3/4" 12-1/2" 4-1/2" 10' 12'
N34-25B 3/4" 3/4" 12-1/2" 9" 17' 25'
N34-50B 3/4" 3/4" 12-1/2" 16" 35' 50'
RIGID COUPLING at both ends
N14-12 1/4" 1/4" 3-1/2" 6" 10' 12'
N14-25 1/4" 1/4" 3-1/2" 10-1/2" 22' 25'
N14-50 1/4" 1/4" 3-1/2" 21" 45' 50'
N38-12 3/8" 3/8" 5-5/8" 5" 10' 12'
N38-25 3/8" 3/8" 5-5/8" 10-1/4" 21' 25'
N38-50 3/8" 3/8" 5-5/8" 21" 44' 50'
N12-12 1/2" 1/2" 9" 5" 9' 12'
N12-25 1/2" 1/2" 9" 9" 18' 25'
N12-50 1/2" 1/2" 9" 18" 41' 50'
BULK HOSEs
N14-100 — 1/4" 3-1/2" 45" 90' 100'
N38-100 — 3/8" 5-5/8" 38" 85' 100'
N12-100 — 1/2" 9" 35" 75' 100'
N34-100 — 3/4" 12-1/2" 29" 70' 100'
Ø
Ø
Model
NPT in ft
Swivel Coupling At One End
P14-10 1/4" 1/4" 10'
P14-20 1/4" 1/4" 20'
P14-30 1/4" 1/4" 30'
P38-10 3/8" 3/8" 10'
P38-20 3/8" 3/8" 20'
P38-30 3/8" 3/8" 30'
Swivel Coupling At Both Ends
P12-10R 1/2" 1/2" 10'
P12-20R 1/2" 1/2" 20'
P12-30R 1/2" 1/2" 30'
Fitting Kits
Model Specifications
P14-RMS 1/4" NPT reusable male swivel fitting kit for 1/4" ID polyurethane hose
P38-RMS 3/8" NPT reusable male swivel fitting kit for 3/8" ID polyurethane hose
P14-RMR 1/4" NPT reusable male rigid fitting kit for 1/4" ID polyurethane hose
P38-RMR 3/8" NPT reusable male rigid fitting kit for 3/8" ID polyurethane hose
P12-RFR 1/2" NPT reusable female rigid fitting kit for 1/2" ID polyurethane hose
P12-RMS 1/2" NPT reusable male rigid fitting kit for 1/2" ID polyurethane hose
27
Ø Ø
Model Description Model
NPT cfm* NPT in (mm)
ASA-1/4 1/4" 0 – 25 Adjustable swivel connectors FEMALE PIPE THREADS
ASC-1/4 1/4" 0 – 33 Non-marring composite R00-147 3/8" 3/8" (10)
swivel connectors
R1-47 3/8" 5/16" (8)
AS-3/8 3/8" 0 – 45 Standard swivel connectors
MALE PIPE THREADS
AS-1/2 1/2" 0 – 65 Standard swivel connectors
A01-46 3/8" 1/2" (13)
A03-46 1/2" 3/4" (19)
Swivels and
Adapters AL-387 3/8" 5/16" (8)
CN-20-S 2" 2" (51)
D01-14 1/4" 3/8" (10)
Swivel Inlets
Model Specifications
Ø
HH1-VSW1/2 1/2" NPT x 1/2" hose barb (general-duty) Model Description
HH1-VSW7/8 7/8" – 24" x 1/2" hose barb (general-duty) in (mm)
MT1-AL34-3/8 3/8" (10 mm) 1 braid rayon
Inlet Bushings MT1-AL34-1/2 1/2" (13 mm) 1 braid rayon
with Screens MT1-AL34-3/4 3/4" (19 mm) 1 braid rayon
MT1-AL34-1 1" (25 mm) 1 braid rayon
Model Description
R0B1J61-565 1/4" male pipe to 1/4" female pipe
ARO Series
Features
• Automatic, pin-type couplers
• Designed for one-way shutoff operation
• All couplers / plugs average flow cfm measured at
90 psi inlet and 10 psig pressure drop
Female Couplers Male Couplers Hose Barb Couplers Female Plugs Male Plugs Hose Barb Plugs
Ø
Model Body Size Model Body Size
in NPT cfm* in NPT
FEMALE COUPLERS FEMALE Plugs
PRSGF22 1/4" 1/4" 32 PRPF22 1/4" 1/4"
PRSGF23 1/4" 3/8" 32 PRPF23 1/4" 3/8"
PRSGF33 3/8" 3/8" 64 PRPF32 3/8" 1/4"
PRSGF34 3/8" 1/2" 64 PRPF33 3/8" 3/8"
PRSGF43 1/2" 3/8" 147 PRPF44 1/2" 1/2"
PRSGF44 1/2" 1/2" 147 MALE plugs
PRSGF46 1/2" 3/4" 147 PRPM22 1/4" 1/4"
MALE COUPLERS PRPM23 1/4" 3/8"
PRSGM22 1/4" 1/4" 32 PRPM32 3/8" 1/4"
Hose Stem Couplers Male NPT Couplers Hose Stem Plugs Male NPT Plugs
Ø Ø
Model Body Size Model Body Size
HOSE STEM COUPLERS HOSE STEM PLUGS
FH-8-1/2 5/8" 1/2" Hose 3/8" MH-8-1/2 5/8" 1/2" Hose 3/8"
FH-8-3/4 5/8" 3/4" Hose 9/16" MH-8-3/4 5/8" 3/4" Hose 5/8"
FH-8-1 1" 1" Hose 13/16" MH-8A-1 5/8" 1" Hose 13/16"
Male NPT COUPLERS MALE NPT PLUGS
FO-8-3/4 5/8" 3/4" MNPT 5/8" MO-8-1/2 5/8" 1/2" MNPT 3/8"
FO-8-3/8 5/8" 3/8" MNPT 3/8" MO-8-3/4 5/8" 3/4" MNPT 5/8"
FO-8-1/2 1" 1" MNPT 15/16" MO-8A-1 1" 1" MNPT 13/16"
Impact Sockets
35
D E
A
Impact Sockets
Features Benefits
Electro-phosphate finish on
D 1/4" to 1" drive sizes
Projects a sleek look and high visibility
ingersollrandproducts.com/accessories
Ø D1
T
L
36
Ø D2
Part # of
Number Pieces Description Contents
A B S62H38 3/8" 0.63 (16) 0.63 (16) 0.31 (8) 0.91 (23) B
S62H716 7/16" 0.67 (17) 0.67 (17) 0.31 (8) 0.91 (23) B
Ø D1 S62H12 1/2" 0.75 (19) 0.75 (19) 0.31 (8) 0.91 (23) B
T
S62H916 9/16" 0.79 (20) 0.79 (20) 0.31 (8) 0.91 (23) B
L
S62M4 4 mm 0.3 (7.6) 0.51 (13) 0.2 (5) 0.91 (23) A
S62M45 4.5 mm 0.32 (8.2) 0.51 (13) 0.2 (5) 0.91 (23) A
Ø D2
S62M5 5 mm 0.35 (8.8) 0.51 (13) 0.2 (5) 0.91 (23) A
S62M55 5.5 mm 0.37 (9.5) 0.51 (13) 0.2 (5) 0.91 (23) A
S62M6 6 mm 0.39 (10) 0.51 (13) 0.28 (7) 0.91 (23) A
S62M7 7 mm 0.44 (11.3) 0.51 (13) 0.28 (7) 0.91 (23) A
S62M8 8 mm 0.49 (12.5) 0.51 (13) 0.28 (7) 0.91 (23) A
S62M9 9 mm 0.55 (14) 0.55 (14) 0.28 (7) 0.91 (23) B
S62M10 10 mm 0.57 (14.5) 0.57 (14.5) 0.28 (7) 0.91 (23) B
S62M11 11 mm 0.67 (17) 0.67 (17) 0.31 (8) 0.91 (23) B
S62M12 12 mm 0.71 (18) 0.71 (18) 0.31 (8) 0.91 (23) B
S62M13 13 mm 0.75 (19) 0.75 (19) 0.31 (8) 0.91 (23) B
S62M14 14 mm 0.79 (20) 0.79 (20) 0.31 (8) 0.91 (23) B
S62M15 15 mm 0.83 (21) 0.83 (21) 0.31 (8) 0.91 (23) B
37
Part Output D1 D2 T L
6-PT Number Size in (mm) in (mm) in (mm) in (mm) Type
DEEP
S62H316L 3/16" 0.33 (8.5) 0.51 (13) 0.2 (5) 1.97 (50) A
S62H732L 7/32" 0.37 (9.5) 0.51 (13) 0.2 (5) 1.97 (50) A
S62H14L 1/4" 0.41 (10.3) 0.51 (13) 0.2 (5) 1.97 (50) A
S62H932L 9/32" 0.44 (11.3) 0.51 (13) 0.28 (7) 1.97 (50) A
S62H516L 5/16" 0.49 (12.5) 0.51 (13) 0.28 (7) 1.97 (50) A
S62H1132L 11/32" 0.55 (14) 0.55 (14) 0.28 (7) 1.97 (50) B
S62H38L 3/8" 0.63 (16) 0.63 (16) 0.31 (8) 1.97 (50) B
S62H716L 7/16" 0.67 (17) 0.67 (17) 0.31 (8) 1.97 (50) B
A B S62H12L 1/2" 0.75 (19) 0.75 (19) 0.31 (8) 1.97 (50) B
S62H916L 9/16" 0.79 (20) 0.79 (20) 0.31 (8) 1.97 (50) B
Impact Sockets
T S62M4L 4 mm 0.3 (7.6) 0.51 (13) 0.2 (5) 1.97 (50) A
Ø D1
S62M45L 4.5 mm 0.32 (8.2) 0.51 (13) 0.2 (5) 1.97 (50) A
L S62M5L 5 mm 0.35 (8.8) 0.51 (13) 0.2 (5) 1.97 (50) A
S62M55L 5.5 mm .37 (9.5) 0.51 (13) 0.2 (5) 1.97 (50) A
S62M6L 6 mm 0.39 (10) 0.51 (13) 0.28 (7) 1.97 (50) A
Ø D2
S62M7L 7 mm 0.44 (11.3) 0.51 (13) 0.28 (7) 1.97 (50) A
S62M8L 8 mm 0.49 (12.5) 0.51 (13) 0.28 (7) 1.97 (50) A
S62M9L 9 mm 0.57 (14.5) 0.57 (14.5) 0.28 (7) 1.97 (50) B
S62M10L 10 mm 0.63 (16) 0.63 (16) 0.28 (7) 1.97 (50) B
S62M11L 11 mm 0.67 (17) 0.67 (17) 0.31 (8) 1.97 (50) B
S62M12L 12 mm 0.67 (17) 0.67 (17) 0.31 (8) 1.97 (50) B
S62M13L 13 mm .75 (19) 0.75 (19) 0.31 (8) 1.97 (50) B
S62M14L 14 mm 0.79 (20) 0.79 (20) 0.31 (8) 1.97 (50) B
Ø D1
T S62M15L 15 mm 0.83 (21) 0.83 (21) 0.31 (8) 1.97 (50) B
UNIVERSAL
L
S62H14U 1/4" 0.47 (12) 0.63 (16) 0.24 (6) 1.73 (44) A
Ø D2
S62H516U 5/16" 0.51 (13) 0.63 (16) 0.24 (6) 1.73 (44) A
D1
S62H38U 3/8" 0.63 (16) 0.63 (16) 0.31 (8) 1.73 (44) A
T
S62H716U 7/16" 0.67 (17) 0.63 (16) 0.31 (8) 1.73 (44) A
S62H12U 1/2" 0.75 (19) 0.63 (16) 0.31 (8) 1.89 (48) A
L
S62H916U 9/16" 0.79 (20) 0.63 (16) 0.31 (8) 1.89 (48) A
S62M5U 5 mm 0.47 (12) 0.63 (16) 0.24 (6) 1.73 (44) A
S62M55U 5.5 mm 0.47 (12) 0.71 (18) 0.24 (6) 1.73 (44) A
D2 S62M6U 6 mm 0.47 (12) 0.71 (18) 0.24 (6) 1.73 (44) A
A
S62M7U 7 mm 0.47 (12) 0.71 (18) 0.24 (6) 1.73 (44) A
S62M8U 8 mm 0.51 (13) 0.71 (18) 0.31 (8) 1.73 (44) A
S62M9U 9 mm 0.59 (15) 0.71 (18) 0.31 (8) 1.73 (44) A
S62M10U 10 mm 0.63 (16) 0.71 (18) 0.31 (8) 1.73 (44) A
S62M11U 11 mm 0.67 (17) 0.71 (18) 0.31 (8) 1.73 (44) A
S62M12U 12 mm 0.67 (17) 0.71 (18) 0.31 (8) 1.89 (48) A
S62M13U 13 mm 0.75 (19) 0.71 (18) 0.31 (8) 1.89 (48) A
S62M14U 14 mm 0.79 (20) 0.71 (18) 0.31 (8) 1.89 (48) A
S62M15U 15 mm 0.83 (21) 0.71 (18) 0.31 (8) 1.89 (48) A
ingersollrandproducts.com/accessories
38 Consumables & Attachments | 1/4" Impact Sockets
Accessories
Description Output Size
39
Ø D2
Impact Sockets
Drive metric set 15 mm, 17 mm, 19 mm
3/8" 9 mm, 10 mm, 11 mm, 13 mm, 14 mm,
SK3M8L 8
Drive deep metric set 15 mm, 17 mm, 19 mm
3/8" 10 mm, 12 mm, 13 mm, 14 mm,
SK3M7U 7 SK3H8
Universal metric set 15 mm, 17 mm, 19 mm
3/8" Combo drive SAE & 3/8", 1/2", 5/8", 11/16",
SK3C8 8
metric set 10 mm, 13 mm, 16 mm, 17 mm
3/8" drive metric 9 mm, 10 mm, 11 mm, 12 mm, 13 mm,
SK3M10 10
standard set 14 mm, 15 mm, 16 mm, 17 mm, 19 mm
Individuals
Part Output D1 D2 T L
6-PT Number Size in (mm) in (mm) in (mm) in (mm) Type
STANDARD
S63H14 1/4" 0.43 (11) 0.75 (19) 0.16 (4) 1.1 (28) A
S63H516 5/16" 0.49 (12.5) 0.75 (19) 0.28 (7) 1.1 (28) A
S63H38 3/8" 0.57 (14.5) 0.75 (19) 0.28 (7) 1.1 (28) A
S63H716 7/16" 0.67 (17) 0.75 (19) 0.28 (7) 1.18 (30) A
S63H12 1/2" 0.75 (19) 0.75 (19) 0.28 (7) 1.18 (30) B
S63H916 9/16" 0.79 (20) 0.79 (20) 0.28 (7) 1.18 (30) B
S63H58 5/8" 0.94 (24) 0.94 (24) 0.39 (10) 1.18 (30) B
A B
S63H1116 11/16" 0.94 (24) 0.94 (24) 0.39 (10) 1.26 (32) B
D1 S63H34 3/4" 1.02 (26) 1.02 (26) 0.39 (10) 1.26 (32) B
T S63H1316 13/16" 1.18 (30) 1.18 (30) 0.51 (13) 1.26 (32) B
S63H78 7/8" 1.26 (32) 1.26 (32) 0.51 (13) 1.26 (32) B
L
S63H1516 15/16" 1.34 (34) 1.34 (34) 0.51 (13) 1.26 (32) B
S63H1 1 mm 1.34 (34) 1.34 (34) 0.51 (13) 1.26 (32) B
D2 S63M6 6 mm 0.41 (10.5) 0.75 (19) 0.16 (4) 1.1 (28) A
S63M7 7 mm 0.45 (11.5) 0.75 (19) 0.28 (7) 1.1 (28) A
S63M8 8 mm 0.49 (12.5) 0.75 (19) 0.28 (7) 1.1 (28) A
S63M9 9 mm 0.55 (14) 0.75 (19) 0.28 (7) 1.1 (28) A
S63M10 10 mm 0.59 (15) 0.75 (19) 0.28 (7) 1.1 (28) A
ingersollrandproducts.com/accessories
40 Consumables & Attachments | 3/8" Impact Sockets
Part Output D1 D2 T L
6-PT Number Size in (mm) in (mm) in (mm) in (mm) Type
STANDARD (cont'd)
S63M11 11 mm 0.67 (17) 0.75 (19) 0.28 (7) 1.18 (30) A
S63M12 12 mm 0.71 (18) 0.75 (19) 0.28 (7) 1.18 (30) A
S63M13 13 mm 0.75 (19) 0.75 (19) 0.28 (7) 1.18 (30) B
S63M14 14 mm 0.79 (20) 0.79 (20) 0.28 (7) 1.18 (30) B
S63M15 15 mm 0.87 (22) 0.87 (22) 0.39 (10) 1.18 (30) B
S63M16 16 mm 0.94 (24) 0.94 (24) 0.39 (10) 1.18 (30) B
S63M17 17 mm 0.94 (24) 0.94 (24) 0.39 (10) 1.26 (32) B
S63M18 18 mm 1.02 (26) 1.02 (26) 0.51 (13) 1.26 (32) B
S63M19 19 mm 1.02 (26) 1.02 (26) 0.51 (13) 1.26 (32) B
S63M20 20 mm 1.1 (28) 1.1 (28) 0.51 (13) 1.26 (32) B
Impact Sockets
Part Output D1 D2 T L
6-PT Number Size in (mm) in (mm) in (mm) in (mm) Type
UNIVERSAL
S63H516U 5/16" 0.69 (17.5) 0.94 (24) 0.47 (12) 2.09 (53) A
S63H38U 3/8" 0.59 (15) 0.94 (24) 0.47 (12) 2.09 (53) A
D1
S63H716U 7/16" 0.73 (18.5) 0.94 (24) 0.47 (12) 2.09 (53) A
T
S63H12U 1/2" 0.75 (19) 0.94 (24) 0.47 (12) 2.09 (53) A
S63H916U 9/16" 0.87 (22) 0.94 (24) 0.47 (12) 2.09 (53) A
L
S63H58U 5/8" 0.94 (24) 0.94 (24) 0.47 (12) 2.09 (53) A
S63H1116U 11/16" 0.98 (25) 0.94 (24) 0.47 (12) 2.09 (53) A
S63H34U 3/4" 1.1 (28) 0.94 (24) 0.47 (12) 2.09 (53) A
D2 S63H1316U 13/16" 1.26 (32) 0.94 (24) 0.47 (12) 2.09 (53) A
A
S63H78U 7/8" 1.26 (32) 0.94 (24) 0.47 (12) 2.09 (53) A
Impact Sockets
S63H1516U 15/16" 1.34 (34) 0.94 (24) 0.47 (12) 2.09 (53) A
S63H1U 1 mm 1.42 (36) 0.94 (24) 0.47 (12) 2.09 (53) A
S63M8U 8 mm 0.69 (17.5) 0.94 (24) 0.47 (12) 2.09 (53) A
S63M9U 9 mm 0.69 (17.5) 0.94 (24) 0.47 (12) 2.09 (53) A
S63M10U 10 mm 0.65 (16.5) 0.94 (24) 0.47 (12) 2.09 (53) A
S63M11U 11 mm 0.75 (19) 0.94 (24) 0.47 (12) 2.09 (53) A
S63M12U 12 mm 0.75 (19) 0.94 (24) 0.47 (12) 2.09 (53) A
S63M13U 13 mm 0.79 (20) 0.94 (24) 0.47 (12) 2.09 (53) A
S63M14U 14 mm 0.87 (22) 0.94 (24) 0.47 (12) 2.09 (53) A
S63M15U 15 mm 0.87 (22) 0.94 (24) 0.47 (12) 2.09 (53) A
S63M16U 16 mm 1.02 (26) 0.94 (24) 0.47 (12) 2.09 (53) A
S63M17U 17 mm 1.02 (26) 0.94 (24) 0.47 (12) 2.09 (53) A
S63M18U 18 mm 1.02 (26) 0.94 (24) 0.47 (12) 2.09 (53) A
S63M19U 19 mm 1.1 (28) 0.94 (24) 0.47 (12) 2.09 (53) A
S63M20U 20 mm 1.26 (32) 0.94 (24) 0.47 (12) 2.09 (53) A
S63M21U 21 mm 1.26 (32) 0.94 (24) 0.47 (12) 2.09 (53) A
S63M22U 22 mm 1.26 (32) 0.94 (24) 0.47 (12) 2.09 (53) A
UNIVERSAL DEEP
S63H516UL 5/16" 0.69 (17.5) 0.94 (24) 0.51 (13) 3.03 (77) A
S63H38UL 3/8" 0.71 (18) 0.94 (24) 0.51 (13) 3.03 (77) A
D1
S63H716UL 7/16" 0.71 (18) 0.94 (24) 0.51 (13) 3.03 (77) A
T
S63H12UL 1/2" 0.75 (19) 0.94 (24) 0.51 (13) 3.03 (77) A
S63H916UL 9/16" 0.83 (21) 0.94 (24) 0.51 (13) 3.03 (77) A
L
S63H58UL 5/8" 0.91 (23) 0.94 (24) 0.51 (13) 3.03 (77) A
S63H1116UL 11/16" 0.98 (25) 0.94 (24) 0.51 (13) 3.03 (77) A
S63H34UL 3/4" 1.06 (27) 0.94 (24) 0.51 (13) 3.03 (77) A
S63H1316UL 13/16" 1.18 (30) 0.94 (24) 0.51 (13) 3.03 (77) A
D2
A S63H78UL 7/8" 1.26 (32) 0.94 (24) 0.51 (13) 3.03 (77) A
S63M8UL 8 mm 0.69 (17.5) 0.94 (24) 0.51 (13) 3.03 (77) A
S63M9UL 9 mm 0.69 (17.5) 0.94 (24) 0.51 (13) 3.03 (77) A
S63M10UL 10 mm 0.71 (18) 0.94 (24) 0.51 (13) 3.03 (77) A
ingersollrandproducts.com/accessories
42 Consumables & Attachments | 3/8" Impact Sockets
Part Output D1 D2 T L
6-PT Number Size in (mm) in (mm) in (mm) in (mm) Type
UNIVERSAL DEEP (cont'd)
S63M11UL 11 mm 0.71 (18) 0.94 (24) 0.51 (13) 3.03 (77) A
S63M12UL 12 mm 0.75 (19) 0.94 (24) 0.51 (13) 3.03 (77) A
S63M13UL 13 mm 0.75 (19) 0.94 (24) 0.51 (13) 3.03 (77) A
S63M14UL 14 mm 0.83 (21) 0.94 (24) 0.51 (13) 3.03 (77) A
S63M15UL 15 mm 0.87 (22) 0.94 (24) 0.51 (13) 3.03 (77) A
S63M16UL 16 mm 1.02 (26) 0.94 (24) 0.51 (13) 3.03 (77) A
Impact Sockets
Accessories
Recommended
Description Output Size
Retaining Ring
A3F4M
3/8" female to 1/2" male adapter 1/2" RR10003
iption
Adapter
J3 Universal joint 3/8" —
Extension
E36H 6" Extension 3/8" RR10003
43
Ø D2
Part # of
Number Pieces Description Contents
SK4M3L 3 1/2 Drive deep metric set 17 mm, 19 mm, 21 mm
SK4M5L 5 1/2" Drive deep metric set 17 mm, 19 mm, 21mm, 22 mm, 24 mm
Impact Sockets
1/2", 9/16", 5/8", 3/4", 7/8",
SK4C10L 10 1/2" Drive deep combo set 13 mm, 16 mm, 17 mm,
19 mm, 21 mm
1/2" Drive 17 mm, 18.5 mm, 20 mm, 21.5 mm,
SK4LNR 8
metric lug nut removal set 23 mm, 24.5 mm, 26 mm, 27.5 mm
Standard: 10 mm, 11 mm, 13mm, 14 mm,
17 mm, 19 mm, 21 mm, 22 mm, 24 mm
SK4M18 18 1/2" Drive metric
Deep: 13 mm, 14 mm, 21 mm, 24 mm
Deep Thin Wall: 17 mm, 19 mm, 21 mm
7/16", 1/2", 9/16", 5/8", 11/16",
SK4H13 13 1/2" Drive standard set 3/4", 13/16", 7/8", 15/16", SK4H13
1", 1-1/16", 1-1/8", 1-1/4"
7/16", 1/2", 9/16", 5/8", 11/16",
1/2" Drive
SK4H13L 13 3/4", 13/16", 7/8",
deep standard set
15/16", 1", 1-1/16", 1-1/8', 1-1/4"
SK4C3F 1/2" Drive lug nut service set 3/4" x 13/16", 19" x 21",
3
(flip socket set) 3" Extension
ingersollrandproducts.com/accessories
44 Consumables & Attachments | 1/2" Impact Sockets
Individuals
Part Output D1 D2 T L
6-PT Number Size in (mm) in (mm) in (mm) in (mm) Type
STANDARD
S64H1516 15/16" 1.34 (34) 1.34 (34) 0.63 (16) 1.73 (44) B
S64H38 3/8" 0.63 (16) 0.87 (22) 0.43 (11) 1.5 (38) A
S64H716 7/16" 0.71 (18) 0.87 (22) 0.43 (11) 1.5 (38) A
S64H12 1/2" 0.77 (19.5) 0.87 (22) 0.43 (11) 1.5 (38) A
S64H916 9/16" 0.85 (21.5) 0.94 (24) 0.43 (11) 1.5 (38) A
S64H58 5/8" 0.94 (24) 0.94 (24) 0.43 (11) 1.5 (38) B
A B C S64H1116 11/16" 1.02 (26) 1.02 (26) 0.43 (11) 1.5 (38) B
S64H34 3/4" 1.1 (28) 1.1 (28) 0.63 (16) 1.57 (40) B
D1
S64H1316 13/16" 1.18 (30) 1.18 (30) 0.63 (16) 1.57 (40) B
Impact Sockets
T
S64H78 7/8" 1.26 (32) 1.26 (32) 0.63 (16) 1.65 (42) B
L
S64H1516 15/16" 1.34 (34) 1.34 (34) 0.63 (16) 1.73 (44) B
S64H1 1" 1.42 (36) 1.42 (36) 0.71 (18) 1.73 (44) B
D2
S64H1-116 1-1/16" 1.5 (38) 1.5 (38) 0.71 (18) 1.81 (46) B
S64H1-18 1-1/8" 1.57 (40) 1.5 (38) 0.71 (18) 1.81 (46) C
S64H1-316 1-3/16" 1.65 (42) 1.5 (38) 0.71 (18) 1.81 (46) C
S64H1-14 1-1/4" 1.73 (44) 1.5 (38) 0.79 (20) 1.81 (46) C
S64H1-516 1-5/16" 1.85 (47) 1.5 (38) 0.79 (20) 1.81 (46) C
S64H1-38 1-3/8" 1.97 (50) 1.5 (38) 0.79 (20) 1.81 (46) C
S64H1-716 1-7/16" 2.01 (51) 1.5 (38) 0.79 (20) 1.81 (46) C
S64H1-12 1-1/2" 2.09 (53) 1.5 (38) 0.87 (22) 1.81 (46) C
S64H1-916 1-9/16" 2.17 (55) 1.73 (44) 0.87 (22) 2.36 (60) C
S64H1-58 1-5/8" 2.28 (58) 1.73 (44) 0.87 (22) 2.36 (60) C
S64H1-1116 1-11/16" 2.4 (61) 1.73 (44) 0.94 (24) 2.36 (60) C
S64H1-34 1-3/4" 2.48 (63) 1.73 (44) 0.94 (24) 2.36 (60) C
S64H1-1316 1-13/16" 2.56 (65) 1.73 (44) 0.94 (24) 2.36 (60) C
S64H1-78 1-7/8" 2.6 (66) 1.73 (44) 0.94 (24) 2.36 (60) C
S64H1-1516 1-15/16" 2.68 (68) 1.73 (44) 0.94 (24) 2.36 (60) C
S64H2 2" 2.76 (70) 2.05 (52) 0.94 (24) 2.36 (60) C
S64H2-116 2-1/16" 2.83 (72) 2.05 (52) 0.94 (24) 2.36 (60) C
S64H2-18 2-1/8" 2.99 (76) 2.05 (52) 1.06 (27) 2.56 (65) C
S64H2-316 2-3/16" 3.03 (77) 2.05 (52) 1.06 (27) 2.56 (65) C
S64H2-14 2-1/4" 3.15 (80) 2.05 (52) 1.06 (27) 2.56 (65) C
S64M8 8 mm 0.57 (14.5) 0.87 (22) 0.35 (9) 1.5 (38) A
S64M9 9 mm 0.57 (14.5) 0.87 (22) 0.43 (11) 1.5 (38) A
S64M10 10 mm 0.67 (17) 0.87 (22) 0.43 (11) 1.5 (38) A
S64M11 11 mm 0.67 (17) 0.87 (22) 0.43 (11) 1.5 (38) A
S64M12 12 mm 0.71 (18) 0.87 (22) 0.43 (11) 1.5 (38) A
S64M13 13 mm 0.79 (20) 0.87 (22) 0.43 (11) 1.5 (38) A
S64M14 14 mm 0.87 (22) 0.94 (24) 0.43 (11) 1.5 (38) A
S64M15 15 mm 0.94 (24) 0.94 (24) 0.43 (11) 1.5 (38) B
45
Part Output D1 D2 T L
6-PT Number Size in (mm) in (mm) in (mm) in (mm) Type
STANDARD (cont'd)
S64M16 16 mm 0.94 (24) 0.94 (24) 0.43 (11) 1.5 (38) B
S64M17 17 mm 1.02 (26) 1.02 (26) 0.43 (11) 1.5 (38) B
S64M18 18 mm 1.02 (26) 1.02 (26) 0.43 (11) 1.5 (38) B
S64M19 19 mm 1.1 (28) 1.1 (28) 0.51 (13) 1.57 (40) B
S64M20 20 mm 1.18 (30) 1.18 (30) 0.51 (13) 1.57 (40) B
S64M21 21 mm 1.18 (30) 1.18 (30) 0.51 (13) 1.57 (40) B
S64M22 22 mm 1.26 (32) 1.26 (32) 0.51 (13) 1.65 (42) B
S64M23 23 mm 1.26 (32) 1.26 (32) 0.51 (13) 1.65 (42) B
S64M24 24 mm 1.34 (34) 1.34 (34) 0.59 (15) 1.73 (44) B
Impact Sockets
S64M25 25 mm 1.38 (35) 1.38 (35) 0.59 (15) 1.73 (44) B
S64M26 26 mm 1.42 (36) 1.42 (36) 0.59 (15) 1.73 (44) B
S64M27 27 mm 1.5 (38) 1.5 (38) 0.72 (18.3) 1.81 (46) B
S64M28 28 mm 1.57 (40) 1.5 (38) 0.72 (18.3) 1.81 (46) C
S64M29 29 mm 1.57 (40) 1.5 (38) 0.72 (18.3) 1.81 (46) C
S64M30 30 mm 1.65 (42) 1.5 (38) 0.72 (18.3) 1.81 (46) C
S64M32 32 mm 1.73 (44) 1.5 (38) 0.72 (18.3) 1.81 (46) C
S64M33 33 mm 1.77 (45) 1.5 (38) 0.79 (20) 1.81 (46) C
S64M34 34 mm 1.81 (46) 1.5 (38) 0.79 (20) 1.81 (46) C
S64M35 35 mm 1.89 (48) 1.5 (38) 0.79 (20) 1.81 (46) C
S64M36 36 mm 1.97 (50) 1.5 (38) 0.79 (20) 1.97 (50) C
DEEP
S64H516L 5/16" 0.55 (14) 0.87 (22) 0.39 (10) 3.07 (78) A
S64H38L 3/8" 0.67 (17) 0.87 (22) 0.55 (14) 3.07 (78) A
S64H716L 7/16" 0.71 (18) 0.87 (22) 0.55 (14) 3.07 (78) A
S64H12L 1/2" 0.79 (20) 0.87 (22) 0.55 (14) 3.07 (78) A
S64H916L 9/16" 0.87 (22) 0.94 (24) 0.55 (14) 3.07 (78) A
S64H58L 5/8" 0.94 (24) 0.94 (24) 0.55 (14) 3.07 (78) B
S64H1116L 11/16" 1.02 (26) 1.02 (26) 0.67 (17) 3.07 (78) B
S64H34L 3/4" 1.1 (28) 1.1 (28) 0.67 (17) 3.07 (78) B
A B C
S64H1316L 13/16" 1.18 (30) 1.18 (30) 0.67 (17) 3.07 (78) B
D1 S64H78L 7/8" 1.26 (32) 1.26 (32) 0.75 (19) 3.07 (78) B
T S64H1516L 15/16" 1.34 (34) 1.34 (34) 0.75 (19) 3.07 (78) B
S64H1L 1" 1.42 (36) 1.42 (36) 0.75 (19) 3.07 (78) B
L
S64H1-116L 1-1/16" 1.5 (38) 1.5 (38) 0.75 (19) 3.07 (78) B
S64H1-18L 1-1/8" 1.57 (40) 1.5 (38) 0.75 (19) 3.07 (78) C
D2 S64H1-316L 1-3/16" 1.65 (42) 1.5 (38) 0.75 (19) 3.07 (78) C
S64H1-14L 1-1/4" 1.73 (44) 1.5 (38) 1.18 (30) 3.07 (78) C
S64H1-516L 1-5/16" 1.85 (47) 1.5 (38) 1.18 (30) 3.15 (80) C
D2 T L
S64H1-38L 1-3/8" 1.97 (50) 1.5 (38) 1.18 (30) 3.15 (80) C
S64H1-716L 1-7/16" 2.01 (51) 1.5 (38) 1.18 (30) 3.15 (80) C
ingersollrandproducts.com/accessories
46 Consumables & Attachments | 1/2" Impact Sockets
Part Output D1 D2 T L
6-PT Number Size in (mm) in (mm) in (mm) in (mm) Type
DEEP (cont'd)
S64H1-12L 1-1/2" 2.09 (53) 1.5 (38) 1.18 (30) 3.15 (80) C
S64H1-916L 1-9/16" 2.17 (55) 1.73 (44) 1.3 (33) 3.54 (90) C
S64H1-58L 1-5/8" 2.28 (58) 1.73 (44) 1.3 (33) 3.54 (90) C
S64H1-1116L 1-11/16" 2.4 (61) 1.73 (44) 1.3 (33) 3.54 (90) C
S64H1-34L 1-3/4" 2.48 (63) 1.73 (44) 1.3 (33) 3.54 (90) C
S64H1-1316L 1-13/16" 2.56 (65) 1.73 (44) 1.38 (35) 3.54 (90) C
S64H1-78L 1-7/8" 2.6 (66) 1.73 (44) 1.38 (35) 3.54 (90) C
S64H1-1516L 1-15/16" 2.68 (68) 1.73 (44) 1.38 (35) 3.54 (90) C
S64H2L 2" 2.76 (70) 2.05 (52) 1.38 (35) 3.54 (90) C
Impact Sockets
S64H2-116 2-1/16" 2.83 (72) 2.05 (52) 1.38 (35) 3.54 (90) C
S64H2-18L 2-1/8" 2.99 (76) 2.05 (52) 1.38 (35) 3.54 (90) C
S64H2-316L 2-3/16" 3.03 (77) 2.05 (52) 1.38 (35) 3.54 (90) C
S64H2-14L 2-1/4" 3.15 (80) 2.05 (52) 1.38 (35) 3.54 (90) C
S64M8L 8 mm 0.55 (14) 0.87 (22) 0.43 (11) 3.07 (78) A
S64M9L 9 mm 0.59 (15) 0.87 (22) 0.55 (14) 3.07 (78) A
S64M10L 10 mm 0.67 (17) 0.87 (22) 0.55 (14) 3.07 (78) A
S64M11L 11 mm 0.71 (18) 0.87 (22) 0.55 (14) 3.07 (78) A
S64M12L 12 mm 0.75 (19) 0.87 (22) 0.55 (14) 3.07 (78) A
S64M13L 13 mm 0.79 (20) 0.94 (24) 0.55 (14) 3.07 (78) A
S64M14L 14 mm 0.87 (22) 0.94 (24) 0.75 (19) 3.07 (78) A
S64M15L 15 mm 0.94 (24) 0.94 (24) 0.75 (19) 3.07 (78) B
S64M16L 16 mm 0.94 (24) 0.94 (24) 0.75 (19) 3.07 (78) B
S64M17L 17 mm 1.02 (26) 1.02 (26) 0.75 (19) 3.07 (78) B
S64M18L 18 mm 1.02 (26) 1.02 (26) 0.75 (19) 3.07 (78) B
S64M19L 19 mm 1.1 (28) 1.1 (28) 0.75 (19) 3.07 (78) B
S64M20L 20 mm 1.18 (30) 1.18 (30) 0.75 (19) 3.07 (78) B
S64M21L 21 mm 1.18 (30) 1.18 (30) 0.83 (21) 3.07 (78) B
S64M22L 22 mm 1.26 (32) 1.26 (32) 0.83 (21) 3.07 (78) B
S64M23L 23 mm 1.26 (32) 1.26 (32) 0.83 (21) 3.07 (78) B
S64M24L 24 mm 1.34 (34) 1.34 (34) 0.83 (21) 3.07 (78) B
S64M25L 25 mm 1.38 (35) 1.38 (35) 0.83 (21) 3.07 (78) B
S64M26L 26 mm 1.42 (36) 1.42 (36) 0.83 (21) 3.07 (78) B
S64M27L 27 mm 1.5 (38) 1.5 (38) 0.83 (21) 3.07 (78) B
S64M28L 28 mm 1.57 (40) 1.5 (38) 0.94 (24) 3.07 (78) C
S64M29L 29 mm 1.57 (40) 1.5 (38) 0.94 (24) 3.07 (78) C
S64M30L 30 mm 1.65 (42) 1.5 (38) 0.94 (24) 3.07 (78) C
S64M32L 32 mm 1.73 (44) 1.5 (38) 0.94 (24) 3.07 (78) C
S64M33L 33 mm 1.77 (45) 1.5 (38) 0.94 (24) 3.07 (78) C
S64M34L 34 mm 1.89 (48) 1.5 (38) 0.94 (24) 3.07 (78) C
S64M35L 35 mm 1.89 (48) 1.5 (38) 0.94 (24) 3.07 (78) C
S64M36L 36 mm 1.97 (50) 1.5 (38) 0.94 (24) 3.07 (78) C
47
Part Output D1 D2 T L
6-PT Number Size in (mm) in (mm) in (mm) in (mm) Type
UNIVERSAL
S64H516U 5/16" 0.75 (19) 1.1 (28) 0.51 (13) 2.6 (66) A
S64H38U 3/8" 0.75 (19) 1.1 (28) 0.51 (13) 2.6 (66) A
S64H716U 7/16" 0.75 (19) 1.1 (28) 0.51 (13) 2.6 (66) A
S64H12U 1/2" 0.75 (19) 1.1 (28) 0.51 (13) 2.6 (66) A
D1
T S64H916U 9/16" 0.87 (22) 1.1 (28) 0.51 (13) 2.6 (66) A
S64H58U 5/8" 0.94 (24) 1.1 (28) 0.51 (13) 2.6 (66) A
L S64H1116U 11/16" 1.02 (26) 1.1 (28) 0.51 (13) 2.6 (66) A
S64H34U 3/4" 1.1 (28) 1.1 (28) 0.51 (13) 2.6 (66) A
S64H1316U 13/16" 1.18 (30) 1.1 (28) 0.51 (13) 2.6 (66) A
Impact Sockets
D2
S64H78U 7/8" 1.26 (32) 1.1 (28) 0.51 (13) 2.6 (66) A
A
S64H1516U 15/16" 1.42 (36) 1.1 (28) 0.51 (13) 2.6 (66) A
S64M10U 10 mm 0.75 (19) 1.1 (28) 0.51 (13) 2.6 (66) A
S64M11U 11 mm 0.75 (19) 1.1 (28) 0.51 (13) 2.6 (66) A
S64M12U 12 mm 0.75 (19) 1.1 (28) 0.51 (13) 2.6 (66) A
S64M13U 13 mm 0.87 (22) 1.1 (28) 0.51 (13) 2.6 (66) A
S64M14U 14 mm 0.87 (22) 1.1 (28) 0.51 (13) 2.6 (66) A
S64M15U 15 mm 0.91 (23) 1.1 (28) 0.51 (13) 2.6 (66) A
S64M16U 16 mm 1.02 (26) 1.1 (28) 0.51 (13) 2.6 (66) A
S64M17U 17 mm 1.02 (26) 1.1 (28) 0.51 (13) 2.6 (66) A
S64M18U 18 mm 1.02 (26) 1.1 (28) 0.51 (13) 2.6 (66) A
S64M19U 19 mm 1.1 (28) 1.1 (28) 0.51 (13) 2.6 (66) A
S64M20U 20 mm 1.18 (30) 1.1 (28) 0.51 (13) 2.6 (66) A
S64M21U 21 mm 1.18 (30) 1.1 (28) 0.51 (13) 2.6 (66) A
S64M22U 22 mm 1.26 (32) 1.1 (28) 0.51 (13) 2.6 (66) A
S64M23U 23 mm 1.26 (32) 1.1 (28) 0.51 (13) 2.6 (66) A
S64M24U 24 mm 1.34 (34) 1.1 (28) 0.51 (13) 2.6 (66) A
UNIVERSAL DEEP
S64H38UL 3/8" 0.87 (22) 1.1 (28) 0.55 (14) 3.54 (90) A
S64H716UL 7/16" 0.87 (22) 1.1 (28) 0.67 (17) 3.54 (90) A
S64H12UL 1/2" 0.87 (22) 1.1 (28) 0.67 (17) 3.54 (90) A
D1
S64H916UL 9/16" 0.87 (22) 1.1 (28) 0.67 (17) 3.54 (90) A
T
S64H58UL 5/8" 0.94 (24) 1.1 (28) 0.67 (17) 3.54 (90) A
S64H1116UL 11/16" 1.02 (26) 1.1 (28) 0.67 (17) 3.54 (90) A
L
S64H34UL 3/4" 1.1 (28) 1.1 (28) 0.67 (17) 3.54 (90) A
S64H1316UL 13/16 1.18 (30) 1.1 (28) 0.67 (17) 3.54 (90) A
S64H78UL 7/8" 1.26 (32) 1.1 (28) 0.67 (17) 3.54 (90) A
D2 S64H1516UL 15/16" 1.34 (34) 1.1 (28) 0.67 (17) 3.54 (90) A
A
S64M10UL 10 mm 0.87 (22) 1.1 (28) 0.55 (14) 3.54 (90) A
S64M11UL 11 mm 0.87 (22) 1.1 (28) 0.67 (17) 3.54 (90) A
S64M12UL 12 mm 0.87 (22) 1.1 (28) 0.67 (17) 3.54 (90) A
S64M13UL 13 mm 0.87 (22) 1.1 (28) 0.67 (17) 3.54 (90) A
ingersollrandproducts.com/accessories
48 Consumables & Attachments | 1/2" Impact Sockets
Part Output D1 D2 T L
6-PT Number Size in (mm) in (mm) in (mm) in (mm) Type
Accessories
Recommended
Description Output Size
Retaining Ring
A4F6Mip-
1/2" female to 3/4" male adapter 3/4" RR10008
tion
Adapter
E45H 5" Extension 1/2" RR10006
Extension
E410H 10" Extension 1/2" RR10006
Extension
E424H 24" Extension 1/2" RR10006
49
Ø D2
SK6H8
Individuals
Part Output D1 D2 T L Recommended
6-PT Number Size in (mm) in (mm) in (mm) in (mm) Type Retaining Ring
STANDARD
S66H12 1/2" 0.91 (23) 1.63 (41.4) 0.51 (13) 2.01 (51) A RR10010
S66H916 9/16" 1 (25.5) 1.63 (41.4) 0.51 (13) 2.01 (51) A RR10010
S66H58 5/8" 1.1 (28) 1.63 (41.4) 0.51 (13) 2.01 (51) A RR10010
S66H1116 11/16" 1.16 (29.5) 1.63 (41.4) 0.51 (13) 2.01 (51) A RR10010
S66H34 3/4" 1.26 (32) 1.63 (41.4) 0.51 (13) 2.01 (51) A RR10010
S66H1316 13/16" 1.38 (35) 1.63 (41.4) 0.51 (13) 2.01 (51) A RR10010
A B C S66H78 7/8" 1.42 (36) 1.63 (41.4) 0.51 (13) 2.01 (51) A RR10010
D1 S66H1516 15/16" 1.52 (38.5) 1.63 (41.4) 0.51 (13) 2.01 (51) A RR10010
T S66H1 1" 1.57 (40) 1.63 (41.4) 0.51 (13) 2.09 (53) A RR10010
L S66H1-116 1-1/16" 1.67 (42.5) 1.73 (44) 0.51 (13) 2.09 (53) A RR10034S
S66H1-18 1-1/8" 1.73 (44) 1.73 (44) 0.63 (16) 2.09 (53) B RR10034S
D2
S66H1-316 1-3/16" 1.81 (46) 1.73 (44) 0.63 (16) 2.09 (53) C RR10034S
S66H1-14 1-1/4" 1.89 (48) 1.73 (44) 0.63 (16) 2.24 (57) C RR10034S
S66H1-516 1-5/16" 1.97 (50) 1.73 (44) 0.75 (19) 2.24 (57) C RR10034S
66H1-38 1-3/8" 2.07 (52.5) 1.73 (44) 0.75 (19) 2.24 (57) C RR10034S
S66H1-716 1-7/16" 2.11 (53.5) 1.73 (44) 0.75 (19) 2.24 (57) C RR10034S
S66H1-12 1-1/2" 2.2 (56) 1.73 (44) 0.87 (22) 2.24 (57) C RR10034S
S66H1-916 1-9/16" 2.3 (58.5) 1.73 (44) 0.87 (22) 2.28 (58) C RR10034S
S66H1-58 1-5/8" 2.36 (60) 1.73 (44) 0.87 (22) 2.28 (58) C RR10034S
S66H1-1116 1-11/16" 2.5 (63.5) 1.73 (44) 1.02 (26) 2.44 (62) C RR10034S
S66H1-34 1-3/4" 2.54 (64.5) 1.73 (44) 1.02 (26) 2.44 (62) C RR10034S
S66H1-1316 1-13/16" 2.6 (66) 1.73 (44) 1.02 (26) 2.44 (62) C RR10034S
ingersollrandproducts.com/accessories
50 Consumables & Attachments | 3/4" Impact Sockets
STANDARD (cont'd)
S66H1-78 1-7/8" 2.68 (68) 1.73 (44) 1.06 (27) 2.68 (68) C RR10034S
S66H1-1516 1-15/16" 2.76 (70) 1.73 (44) 1.06 (27) 2.68 (68) C RR10034S
S66H2 2" 2.8 (71) 1.73 (44) 1.06 (27) 2.68 (68) C RR10034S
S66H2-116 2-1/16" 2.91 (74) 2.13 (54) 1.22 (31) 2.8 (71) C RR10015S
SS6H2-18 2-1/8" 2.99 (76) 2.13 (54) 1.22 (31) 2.8 (71) C RR10015S
S66H2-316 2-3/16" 3.07 (78) 2.13 (54) 1.22 (31) 2.8 (71) C RR10015S
S66H2-14 2-1/4" 3.15 (80) 2.13 (54) 1.3 (33) 2.87 (73) C RR10015S
S66H2-516 2-5/16" 3.21 (81.5) 2.13 (54) 1.3 (33) 2.87 (73) C RR10015S
S66H2-38 2-3/8" 3.29 (83.5) 2.13 (54) 1.34 (34) 2.87 (73) C RR10015S
Impact Sockets
S66H2-716 2-7/16" 3.35 (85) 2.13 (54) 1.34 (34) 2.95 (75) C RR10015S
S66H2-12 2-1/2" 3.41 (86.5) 2.13 (54) 1.34 (34) 2.95 (75) C RR10015S
S66M17 17 mm 1.18 (30) 1.73 (44) 0.51 (13) 2.01 (51) A RR10034S
S66M18 18 mm 1.22 (31) 1.73 (44) 0.51 (13) 2.01 (51) A RR10034S
S66M19 19 mm 1.28 (32.5) 1.73 (44) 0.51 (13) 2.01 (51) A RR10034S
S66M20 20 mm 1.32 (33.5) 1.73 (44) 0.51 (13) 2.01 (51) A RR10034S
S66M21 21 mm 1.38 (35) 1.73 (44) 0.51 (13) 2.01 (51) A RR10034S
S66M22 22 mm 1.42 (36) 1.73 (44) 0.51 (13) 2.01 (51) A RR10034S
S66M23 23 mm 1.48 (37.5) 1.73 (44) 0.51 (13) 2.01 (51) A RR10034S
S66M24 24 mm 1.52 (38.5) 1.73 (44) 0.63 (16) 2.01 (51) A RR10034S
S66M25 25 mm 1.57 (40) 1.73 (44) 0.63 (16) 2.09 (53) A RR10034S
S66M26 26 mm 1.61 (41) 1.73 (44) 0.63 (16) 2.09 (53) A RR10034S
S66M27 27 mm 1.67 (42.5) 1.73 (44) 0.63 (16) 2.09 (53) A RR10034S
S66M28 28 mm 1.73 (44) 1.73 (44) 0.75 (19) 2.09 (53) B RR10034S
S66M29 29 mm 1.77 (45) 1.73 (44) 0.75 (19) 2.09 (53) C RR10034S
S66M30 30 mm 1.81 (46) 1.73 (44) 0.75 (19) 2.09 (53) C RR10034S
S66M31 31 mm 1.87 (47.5) 1.73 (44) 0.75 (19) 2.24 (57) C RR10034S
S66M32 32 mm 1.91 (48.5) 1.73 (44) 0.75 (19) 2.24 (57) C RR10034S
S66M33 33 mm 1.97 (50) 1.73 (44) 0.87 (22) 2.24 (57) C RR10034S
S66M34 34 mm 2.01 (51) 1.73 (44) 0.87 (22) 2.24 (57) C RR10034S
S66M35 35 mm 2.07 (52.5) 1.73 (44) 0.87 (22) 2.24 (57) C RR10034S
S66M36 36 mm 2.11 (53.5) 1.73 (44) 0.87 (22) 2.24 (57) C RR10034S
S66M37 37 mm 2.17 (55) 1.73 (44) 0.87 (22) 2.24 (57) C RR10034S
S66M38 38 mm 2.2 (56) 1.73 (44) 0.87 (22) 2.24 (57) C RR10034S
S66M40 40 mm 2.3 (58.5) 1.73 (44) 0.87 (22) 2.28 (58) C RR10034S
S66M41 41 mm 2.36 (60) 1.73 (44) 0.87 (22) 2.28 (58) C RR10034S
S66M42 42 mm 2.4 (61) 1.73 (44) 0.98 (25) 2.28 (58) C RR10034S
S66M43 43 mm 2.46 (62.5) 1.73 (44) 0.98 (25) 2.44 (62) C RR10034S
S66M44 44 mm 2.52 (64) 1.73 (44) 0.98 (25) 2.44 (62) C RR10034S
S66M46 46 mm 2.6 (66) 1.73 (44) 0.98 (25) 2.44 (62) C RR10034S
S66M50 50 mm 2.8 (71) 1.73 (44) 1.18 (30) 2.68 (68) C RR10034S
51
DEEP
S66H12L 1/2" 0.91 (23) 1.63 (41.4) 0.63 (16) 3.54 (90) A RR10010
S66H916L 9/16" 1 (25.5) 1.63 (41.4) 0.63 (16) 3.54 (90) A RR10010
S66H58L 5/8" 1.1 (28) 1.63 (41.4) 0.63 (16) 3.54 (90) A RR10010
S66H1116L 11/16" 1.16 (29.5) 1.63 (41.4) 0.63 (16) 3.54 (90) A RR10010
S66H34L 3/4" 1.26 (32) 1.63 (41.4) 0.63 (16) 3.54 (90) A RR10010
S66H1316L 13/16" 1.38 (35) 1.63 (41.4) 0.63 (16) 3.54 (90) A RR10010
S66H78L 7/8" 1.42 (36) 1.63 (41.4) 0.63 (16) 3.54 (90) A RR10010
S66H1516L 15/16" 1.52 (38.5) 1.63 (41.4) 0.63 (16) 3.54 (90) A RR10010
A B C
S66H1L 1" 1.57 (40) 1.63 (41.4) 0.63 (16) 3.54 (90) A RR10010
Impact Sockets
S66H1-116L 1-1/16" 1.67 (42.5) 1.73 (44) 0.63 (16) 3.54 (90) A RR10034S
D1
S66H1-18L 1-1/8" 1.73 (44) 1.73 (44) 0.63 (16) 3.54 (90) B RR10034S
T
S66H1-316L 1-3/16" 1.81 (46) 1.73 (44) 0.63 (16) 3.54 (90) C RR10034S
L
S66H1-14L 1-1/4" 1.91 (48.5) 1.73 (44) 0.63 (16) 3.54 (90) C RR10034S
S66H1-516L 1-5/16" 1.97 (50) 1.73 (44) 0.87 (22) 3.54 (90) C RR10034S
D2 S66H1-38L 1-3/8" 2.07 (52.5) 1.73 (44) 0.87 (22) 3.54 (90) C RR10034S
S66H1-716L 1-7/16" 2.11 (53.5) 1.73 (44) 0.87 (22) 3.54 (90) C RR10034S
D2 T L S66H1-12L 1-1/2" 2.2 (56) 1.73 (44) 0.87 (22) 3.54 (90) C RR10034S
S66H1-916L 1-9/16" 2.3 (58.5) 1.73 (44) 0.87 (22) 3.54 (90) C RR10034S
S66H1-58L 1-5/8" 2.36 (60) 1.73 (44) 0.87 (22) 3.54 (90) C RR10034S
S66H1-1116L 1-11/16" 2.5 (63.5) 1.73 (44) 1.06 (27) 3.54 (90) C RR10034S
S66H1-34L 1-3/4" 2.54 (64.5) 1.73 (44) 1.06 (27) 3.54 (90) C RR10034S
S66H1-1316L 1-13/16" 2.6 (66) 1.73 (44) 1.06 (27) 3.54 (90) C RR10034S
S66H1-78L 1-7/8" 2.68 (68) 1.73 (44) 1.06 (27) 3.54 (90) C RR10034S
S66H1-1516L 1-15/16" 2.76 (70) 1.73 (44) 1.06 (27) 3.54 (90) C RR10034S
S66H2L 2" 2.8 (71) 1.73 (44) 1.06 (27) 3.54 (90) C RR10034S
S66H2-116L 2-1/16" 2.91 (74) 2.13 (54) 1.22 (31) 3.94 (100) C RR10015S
S66H2-18L 2-1/8" 2.99 (76) 2.13 (54) 1.22 (31) 3.94 (100) C RR10015S
S66H2-316L 2-3/16" 3.07 (78) 2.13 (54) 1.22 (31) 3.94 (100) C RR10015S
S66H2-14L 2-1/4" 3.15 (80) 2.13 (54) 1.34 (34) 3.94 (100) C RR10015S
S66H2-516L 2-5/16" 3.21 (81.5) 2.13 (54) 1.34 (34) 4.13 (105) C RR10015S
S66H2-38L 2-3/8" 3.29 (83.5) 2.13 (54) 1.34 (34) 4.13 (105) C RR10015S
S66H2-716L 2-7/16" 3.35 (85) 2.13 (54) 1.34 (34) 4.13 (105) C RR10015S
S66H2-12L 2-1/2" 3.39 (86) 2.13 (54) 1.34 (34) 4.13 (105) C RR10015S
S66M17L 17 mm 1.18 (30) 1.73 (44) 0.75 (19) 3.54 (90) A RR10034S
S66M19L 19 mm 1.28 (32.5) 1.73 (44) 0.75 (19) 3.54 (90) A RR10034S
S66M20L 20 mm 1.32 (33.5) 1.73 (44) 0.75 (19) 3.54 (90) A RR10034S
S66M21L 21 mm 1.38 (35) 1.73 (44) 0.75 (19) 3.54 (90) A RR10034S
S66M22L 22 mm 1.42 (36) 1.73 (44) 0.75 (19) 3.54 (90) A RR10034S
S66M23L 23 mm 1.48 (37.5) 1.73 (44) 0.75 (19) 3.54 (90) A RR10034S
S66M24L 24 mm 1.52 (38.5) 1.73 (44) 0.75 (19) 3.54 (90) A RR10034S
ingersollrandproducts.com/accessories
52 Consumables & Attachments | 3/4" Impact Sockets
DEEP (cont'd)
S66M25L 25 mm 1.57 (40) 1.73 (44) 0.75 (19) 3.54 (90) A RR10034S
S66M26L 26 mm 1.61 (41) 1.73 (44) 0.87 (22) 3.54 (90) A RR10034S
S66M27L 27 mm 1.67 (42.5) 1.73 (44) 0.87 (22) 3.54 (90) A RR10034S
S66M28L 28 mm 1.73 (44) 1.73 (44) 0.87 (22) 3.54 (90) B RR10034S
S66M29L 29 mm 1.77 (45) 1.73 (44) 0.87 (22) 3.54 (90) C RR10034
S66M30L 30 mm 1.81 (46) 1.73 (44) 0.87 (22) 3.54 (90) C RR10034S
S66M31L 31 mm 1.87 (47.5) 1.73 (44) 0.87 (22) 3.54 (90) C RR10034S
S66M32L 32 mm 1.91 (48.5) 1.73 (44) 0.87 (22) 3.54 (90) C RR10034S
S66M33L 33 mm 1.97 (50) 1.73 (44) 0.98 (25) 3.54 (90) C RR10034S
Impact Sockets
S66M34L 34 mm 2.01 (51) 1.73 (44) 0.98 (25) 3.54 (90) C RR10034S
S66M35L 35 mm 2.07 (52.5) 1.73 (44) 0.98 (25) 3.54 (90) C RR10034S
S66M36L 36 mm 2.11 (53.5) 1.73 (44) 0.98 (25) 3.54 (90) C RR10034S
S66M38L 38 mm 2.2 (56) 1.73 (44) 0.98 (25) 3.54 (90) C RR10034S
S66M40L 40 mm 2.3 (58.5) 1.73 (44) 1.18 (30) 3.54 (90) C RR10034S
S66M41L 41 mm 2.36 (60) 1.73 (44) 1.18 (30) 3.54 (90) C RR10034S
S66M42L 42 mm 2.4 (61) 1.73 (44) 1.18 (30) 3.54 (90) C RR10034S
S66M43L 43 mm 2.46 (62.5) 1.73 (44) 1.18 (30) 3.54 (90) C RR10034S
S66M44L 44 mm 2.52 (64) 1.73 (44) 1.18 (30) 3.54 (90) C RR10034S
S66M46L 46 mm 2.6 (66) 1.73 (44) 1.18 (30) 3.54 (90) C RR10034S
S66M50L 50 mm 2.8 (71) 1.73 (44) 1.18 (30) 3.54 (90) C RR10034S
UNIVERSAL
S66H1116U 11/16" 1.14 (29) 1.73 (44) 0.51 (13) 3.74 (95) A RR10034S
S66H34U 3/4" 1.26 (32) 1.73 (44) 0.51 (13) 3.74 (95) A RR10034S
S66H1316U 13/16" 1.38 (35) 1.73 (44) 0.51 (13) 3.74 (95) A RR10034S
D1 S66H78U 7/8" 1.46 (37) 1.73 (44) 0.51 (13) 3.74 (95) A RR10034S
T S66H1516U 15/16" 1.54 (39) 1.73 (44) 0.51 (13) 3.74 (95) A RR10034S
S66H1U 1" 1.61 (41) 1.73 (44) 0.51 (13) 3.94 (100) A RR10034S
L S66H1-116U 1-1/16" 1.69 (43) 1.73 (44) 0.67 (17) 3.94 (100) A RR10034S
S66H1-18U 1-1/8" 1.73 (44) 1.73 (44) 0.67 (17) 3.94 (100) A RR10034S
S66H1-316U 1-3/16" 1.85 (47) 1.73 (44) 0.67 (17) 3.94 (100) A RR10034S
S66H1-14U 1-1/4" 1.93 (49) 1.73 (44) 0.67 (17) 4.13 (105) A RR10034S
D2
A S66H1-516U 1-5/16" 2.01 (51) 1.73 (44) 0.75 (19) 4.13 (105) A RR10034S
S66H1-38U 1-3/8" 2.09 (53) 1.73 (44) 0.75 (19) 4.13 (105) A RR10034S
S66H1-716U 1-7/16" 2.13 (54) 1.73 (44) 0.75 (19) 4.33 (110) A RR10034S
S66H1-12U 1-1/2" 2.24 (57) 1.73 (44) 0.87 (22) 4.33 (110) A RR10034S
S66H1-916U 1-9/16" 2.36 (60) 1.73 (44) 0.87 (22) 4.33 (110) A RR10034S
S66H1-58U 1-5/8" 2.36 (60) 1.73 (44) 0.87 (22) 4.53 (115) A RR10034S
S66H1-1116U 1-11/16" 2.48 (63) 1.73 (44) 1.06 (27) 4.53 (115) A RR10034S
S66H1-34U 1-3/4" 2.52 (64) 1.73 (44) 1.06 (27) 4.53 (115) A RR10034S
S66H1-1316U 1-13/16" 2.6 (66) 1.73 (44) 1.06 (27) 4.53 (115) A RR10034S
53
UNIVERSAL (cont'd)
S66H1-78U 1-7/8" 2.68 (68) 1.73 (44) 1.06 (27) 4.53 (115) A RR10034S
S66M17U 17 mm 1.14 (29) 1.73 (44) 0.47 (12) 3.74 (95) A RR10034S
S66M19U 19 mm 1.26 (32) 1.73 (44) 0.47 (12) 3.74 (95) A RR10034S
S66M20U 20 mm 1.34 (34) 1.73 (44) 0.47 (12) 3.74 (95) A RR10034S
S66M21U 21 mm 1.38 (35) 1.73 (44) 0.47 (12) 3.74 (95) A RR10034S
S66M22U 22 mm 1.46 (37) 1.73 (44) 0.55 (14) 3.74 (95) A RR10034S
S66M23U 23 mm 1.5 (38) 1.73 (44) 0.55 (14) 3.74 (95) A RR10034S
S66M24U 24 mm 1.54 (39) 1.73 (44) 0.55 (14) 3.74 (95) A RR10034S
S66M25U 25 mm 1.61 (41) 1.73 (44) 0.55 (14) 3.94 (100) A RR10034S
Impact Sockets
S66M26U 26 mm 1.65 (42) 1.73 (44) 0.67 (17) 3.94 (100) A RR10034S
S66M27U 27 mm 1.69 (43) 1.73 (44) 0.67 (17) 3.94 (100) A RR10034S
S66M28U 28 mm 1.73 (44) 1.73 (44) 0.67 (17) 3.94 (100) A RR10034S
S66M29U 29 mm 1.81 (46) 1.73 (44) 0.67 (17) 3.94 (100) A RR10034S
S66M30U 30 mm 1.85 (47) 1.73 (44) 0.67 (17) 3.94 (100) A RR10034S
S66M31U 31 mm 1.89 (48) 1.73 (44) 0.83 (21) 4.13 (105) A RR10034S
S66M32U 32 mm 1.93 (49) 1.73 (44) 0.83 (21) 4.13 (105) A RR10034S
S66M33U 33 mm 2.01 (51) 1.73 (44) 0.83 (21) 4.13 (105) A RR10034S
S66M34U 34 mm 2.05 (52) 1.73 (44) 0.83 (21) 4.13 (105) A RR10034S
S66M35U 35 mm 2.09 (53) 1.73 (44) 0.83 (21) 4.13 (105) A RR10034S
S66M36U 36 mm 2.13 (54) 1.73 (44) 0.91 (23) 4.33 (110) A RR10034S
S66M37U 37 mm 2.2 (56) 1.73 (44) 0.91 (23) 4.33 (110) A RR10034S
S66M38U 38 mm 2.24 (57) 1.73 (44) 0.91 (23) 4.33 (110) A RR10034S
S66M39U 39 mm 2.32(59) 1.73 (44) 0.91 (23) 4.33 (110) A RR10034S
S66M40U 40 mm 2.36 (60) 1.73 (44) 0.91 (23) 4.33 (110) A RR10034S
S66M41U 41 mm 2.36 (60) 1.73 (44) 1.02 (26) 4.53 (115) A RR10034S
S66M42U 42 mm 2.44 (62) 1.73 (44) 1.02 (26) 4.53 (115) A RR10034S
S66M43U 43 mm 2.48 (63) 1.73 (44) 1.02 (26) 4.53 (115) A RR10034S
S66M44U 44 mm 2.52 (64) 1.73 (44) 1.14 (29) 4.53 (115) A RR10034S
S66M45U 45 mm 2.6 (66) 1.73 (44) 1.14 (29) 4.53 (115) A RR10034S
S66M46U 46 mm 2.6 (66) 1.73 (44) 1.14 (29) 4.53 (115) A RR10034S
ingersollrandproducts.com/accessories
54 Consumables & Attachments | 3/4" Impact Sockets
Accessories
Recommended
Description Output Size Retaining Ring
A6F8Mp- 1"
3/4" female to 1" male adapter RR10034S
tion
55
Ø D2
Impact Sockets
1" Drive 13/16" square; 33 mm & 1-1/2" deep hex;
SK8C5T 5
truck service set 1-1/8" and 1-1/4" deep thin wall hex
SK8H8L
SK8M4L 1" Drive
4 27 mm, 30 mm, 32 mm, 33 mm
deep metric set
Individuals
Part Output D1 D2 T L Recommended
6-PT Number Size in (mm) in (mm) in (mm) in (mm) Type Retaining Ring
STANDARD
S68H34 3/4" 1.38 (35) 2.13 (54) 0.67 (17) 2.28 (58) A RR10015S
S68H1316 13/16" 1.48 (37.5) 2.13 (54) 0.67 (17) 2.28 (58) A RR10015S
S68H78 7/8" 1.54 (39) 2.13 (54) 0.67 (17) 2.28 (58) A RR10015S
S68H1516 15/16" 1.59 (40.5) 2.13 (54) 0.67 (17) 2.28 (58) A RR10015S
S68H1 1" 1.67 (42.5) 2.13 (54) 0.67 (17) 2.36 (60) A RR10015S
S68H1-116 1-1/16" 1.75 (44.5) 2.13 (54) 0.67 (17) 2.36 (60) A RR10015S
A B C
S68H1-18 1-1/8" 1.81 (46) 2.13 (54) 0.67 (17) 2.44 (62) A RR10015S
D1
S68H1-316 1-3/16" 1.93 (49) 2.13 (54) 0.67 (17) 2.44 (62) A RR10015S
T
S68H1-14 1-1/4" 2.13 (54) 2.13 (54) 0.75 (19) 2.48 (63) A RR10015S
L
S68H1-516 1-5/16 2.13 (54) 2.13 (54) 0.75 (19) 2.48 (63) A PR10015S
D2 S68H1-38 1-3/8" 2.17 (55) 2.13 (54) 0.75 (19) 2.6 (66) C RR10015S
S68H1-716 1-7/16" 2.22 (56.5) 2.13 (54) 0.75 (19) 2.6 (66) C RR10015S
S68H1-12 1-1/2" 2.32 (59) 2.13 (54) 0.87 (22) 2.6 (66) C RR10015S
S68H1-916 1-9/16" 2.4 (61) 2.13 (54) 0.87 (22) 2.6 (66) C RR10015S
S68H1-58 1-5/8" 2.46 (62.5) 2.13 (54) 0.87 (22) 2.68 (68) C RR10015S
S68H1-1116 1-11/16" 2.56 (65) 2.13 (54) 0.98 (25) 2.76 (70) C RR10015S
S68H1-34 1-3/4" 2.66 (67.5) 2.37 (60.3) 0.98 (25) 2.76 (70) C RR10015S
S68H1-1316 1-13/16" 2.72 (69) 2.37 (60.3) 1.06 (27) 2.83 (72) C RR10015
S68H1-78 1-7/8" 2.76 (70) 2.37 (60.3) 1.06 (27) 2.83 (72) C RR10015S
S68H1-1516 1-15/16" 2.85 (72.5) 2.37 (60.3) 1.06 (27) 2.99 (76) C RR10015S
S68H2 2" 2.91 (74) 2.37 (60.3) 1.06 (27) 2.99 (76) C RR10015S
ingersollrandproducts.com/accessories
56 Consumables & Attachments | 1" Impact Sockets
STANDARD (cont'd)
S68H2-116 2-1/16" 3.01 (76.5) 2.37 (60.3) 1.22 (31) 3.15 (80) C RR10015S
S68H2-18 2-1/8" 3.11 (79) 2.37 (60.3) 1.22 (31) 3.15 (80) C RR10015S
S68H2-316 2-3/16" 3.15 (80) 2.37 (60.3) 1.22 (31) 3.31 (84) C RR10015S
S68H2-14 2-1/4" 3.25 (82.5) 2.37 (60.3) 1.34 (34) 3.31 (84) C RR10015S
S68H2-516 2-5/16" 3.31 (84) 2.37 (60.3) 1.34 (34) 3.31 (84) C RR10015S
S68H2-38 2-3/8" 3.41 (86.5) 2.37 (60.3) 1.34 (34) 3.46 (88) C RR10015S
S68H2-716 2-7/16" 3.5 (89) 2.37 (60.3) 1.42 (36) 3.46 (88) C RR10015S
A B C S68H2-12 2-1/2" 3.6 (91.5) 2.37 (60.3) 1.42 (36) 3.46 (88) C RR10015S
D1 S68H2-916 2-9/16" 3.64 (92.5) 2.37 (60.3) 1.42 (36) 3.62 (92) C RR10015S
Impact Sockets
T S68H2-58 2-5/8" 3.74 (95) 2.37 (60.3) 1.5 (38) 3.62 (92) C RR10015S
L S68H2-1116 2-11/16" 3.8 (96.5) 2.37 (60.3) 1.5 (38) 3.78 (96) C RR10015S
S68H2-34 2-3/4" 63.9 (99) 2.37 (60.3) 1.5 (38) 3.78 (96) C RR10015S
D2
S68H2-1316 2-13/16" 4 (101.5) 2.37 (60.3) 1.61 (41) 3.78 (96) C RR10015S
S68H2-78 2-7/8" 4.04 (102.5) 2.37 (60.3) 1.61 (41) 3.78 (96) C RR10015S
S68H2-1516 2-15/16" 4.11 (104.5) 2.37 (60.3) 1.61 (41) 3.94 (100) C RR10015S
S68H3 3" 4.19 (106.5) 2.37 (60.3) 1.73 (44) 3.94 (100) C RR10015S
S68H3-18 3-1/8" 4.37 (111) 2.37 (60.3) 1.73 (44) 3.94 (100) C RR10015S
S68H3-14 3-1/4" 4.53 (115) 3.39 (86) 1.73 (44) 4.02 (102) C RR10025S
S68H3-38 3-3/8" 4.69 (119) 3.39 (86) 1.93 (49) 4.17 (106) C RR10025S
S68H3-12 3-1/2" 4.88 (124) 3.39 (86) 1.93 (49) 4.25 (108) C RR10025S
S68H3-58 3-5/8" 5 (127) 3.39 (86) 2.09 (53) 4.33 (110) C RR10025S
S68H3-34 3-3/4" 5.12 (130) 3.39 (86) 2.09 (53) 4.33 (110) C RR10025S
S68H3-78 3-7/8" 5.35 (136) 3.74 (95) 2.2 (56) 4.53 (115) C RR10025S
S68H4 4" 5.51 (140) 3.74 (95) 2.2 (56) 4.53 (115) C RR10025S
S68H4-18 4-1/8" 5.63 (143) 3.74 (95) 2.32 (59) 4.72 (120) C RR10025S
S68H4-14 4-1/4" 5.75 (146) 3.74 (95) 2.32 (59) 4.72 (120) C RR10025S
S68H4-38 4-3/8" 5.87 (149) 3.74 (95) 2.4 (61) 4.72 (120) C RR10025S
S68H4-12 4-1/2" 5.98 (152) 3.74 (95) 2.4 (61) 4.72 (120) C RR10025S
S68M19 19 mm 1.38 (35) 2.13 (54) 0.67 (17) 2.28 (58) A RR10015S
S68M21 21 mm 1.48 (37.5) 2.13 (54) 0.67 (17) 2.28 (58) A RR10015S
S68M22 22 mm 1.54 (39) 2.13 (54) 0.67 (17) 2.28 (58) A RR10015S
S68M23 23 mm 1.57 (40) 2.13 (54) 0.67 (17) 2.28 (58) A RR10015S
S68M24 24 mm 1.63 (41.5) 2.13 (54) 0.67 (17) 2.28 (58) A RR10015S
S68M25 25 mm 1.67 (42.5) 2.13 (54) 0.67 (17) 2.36 (60) A RR10015S
S68M26 26 mm 1.73 (44) 2.13 (54) 0.67 (17) 2.36 (60) A RR10015S
S68M27 27 mm 1.77 (45) 2.13 (54) 0.67 (17) 2.36 (60) A RR10015S
S68M28 28 mm 1.83 (46.5) 2.13 (54) 0.67 (17) 2.36 (60) A RR10015S
S68M29 29 mm 1.87 (47.5) 2.13 (54) 0.75 (19) 2.44 (62) A RR10015S
S68M30 30 mm 1.93 (49) 2.13 (54) 0.75 (19) 2.44 (62) A RR10015S
S68M31 31 mm 1.97 (50) 2.13 (54) 0.75 (19) 2.44 (62) A RR10015S
57
STANDARD (cont'd)
S68M32 32 mm 2.03 (51.5) 2.13 (54) 0.75 (19) 2.48 (63) A RR10015S
S68M33 33 mm 2.07 (52.5) 2.13 (54) 0.83 (21) 2.48 (63) A RR10015S
S68M34 34 mm 2.13 (54) 2.13 (54) 0.83 (21) 2.48 (63) B RR10015S
S68M35 35 mm 2.17 (55) 2.13 (54) 0.83 (21) 2.6 (66) C RR10015S
S68M36 36 mm 2.22 (56.5) 2.13 (54) 0.91 (23) 2.6 (66) C RR10015S
S68M38 38 mm 2.32 (59) 2.13 (54) 0.91 (23) 2.6 (66) C RR10015S
S68M40 40 mm 2.4 (61) 2.13 (54) 0.91 (23) 2.6 (66) C RR10015S
S68M41 41 mm 2.46 (62.5) 2.13 (54) 0.98 (25) 2.68 (68) C RR10015S
S68M42 42 mm 62.52 (64) 2.13 (54) 0.98 (25) 2.68 (68) C RR10015S
Impact Sockets
S68M43 43 mm 2.56 (65) 2.13 (54) 0.98 (25) 2.76 (70) C RR10015S
S68M45 45 mm 2.66 (67.5) 2.13 (54) 0.98 (25) 2.76 (70) C RR10015S
S68M46 46 mm 2.72 (69) 2.13 (54) 1.14 (29) 2.83 (72) C RR10015S
S68M48 48 mm 2.81 (71.5) 2.13 (54) 1.14 (29) 2.99 (76) C RR10015S
S68M50 50 mm 2.91 (74) 2.13 (54) 1.22 (31) 2.99 (76) C RR10015S
S68M52 52 mm 3.01 (76.5) 2.13 (54) 1.22 (31) 3.15 (80) C RR10015S
S68M54 54 mm 3.11 (79) 2.13 (54) 1.22 (31) 3.15 (80) C RR10015S
S68M55 55 mm 3.15 (80) 2.13 (54) 1.34 (34) 3.31 (84) C RR10015S
S68M56 56 mm 3.21 (81.5) 2.13 (54) 1.34 (34) 3.31 (84) C RR10015S
S68M58 58 mm 3.31 (84) 2.13 (54) 1.34 (34) 3.31 (84) C RR10015S
S68M60 60 mm 3.41 (86.5) 2.13 (54) 1.38 (35) 3.46 (88) C RR10015S
S68M65 65 mm 3.64 (92.5) 2.13 (54) 1.38 (35) 3.62 (92) C RR10015S
S68M70 70 mm 3.9 (99) 2.13 (54) 1.38 (35) 3.78 (96) C RR10015S
S68M75 75 mm 4.13 (105) 2.37 (60.3) 1.38 (35) 4.02 (102) C RR10015S
S68M80 80 mm 4.39 (111.5) 2.37 (60.3) 1.38 (35) 4.02 (102) C RR10015S
S68M85 85 mm 4.63 (117.5) 3.39 (86) 1.38 (35) 4.17 (106) C RR10025S
S68M90 90 mm 4.88 (124) 3.39 (86) 1.38 (35) 4.25 (108) C RR10025S
S68M95 95 mm 5.12 (130) 3.39 (86) 1.38 (35) 4.33 (110) C RR10025S
DEEP
S68H34L 3/4" 1.38 (35) 2.13 (54) 0.98 (25) 3.54 (90) A RR10015S
S68H1316L 13/16" 1.46 (37) 2.13 (54) 0.98 (25) 3.54 (90) A RR10015S
S68H78L 7/8" 1.54 (39) 2.13 (54) 0.98 (25) 3.54 (90) A RR10015S
S68H1516L 15/16" 1.59 (40.5) 2.13 (54) 0.98 (25) 3.54 (90) A RR10015S
S68H1L 1" 1.67 (42.5) 2.13 (54) 0.98 (25) 3.54 (90) A RR10015S
A B C S68H1-116L 1-1/16" 1.75 (44.5) 2.13 (54) 0.98 (25) 3.54 (90) A RR10015S
D1 S68H1-18L 1-1/8" 1.81 (46) 2.13 (54) 0.98 (25) 3.54 (90) A RR10015S
T
S68H1-316L 1-3/16" 1.93 (49) 2.13 (54) 0.98 (25) 3.54 (90) A RR10015S
L
S68H1-14L 1-1/4" 2.03 (51.5) 2.13 (54) 0.98 (25) 3.54 (90) A RR10015S
S68H1-516L 1-5/16" 2.13 (54) 2.13 (54) 0.98 (25) 3.54 (90) B RR10015S
S68H1-38L 1-3/8" 2.17 (55) 2.13 (54) 0.98 (25) 3.54 (90) C RR10015S
D2 S68H1-716L 1-7/16" 2.22 (56.5) 2.13 (54) 0.98 (25) 3.54 (90) C RR10015S
D2 T L
ingersollrandproducts.com/accessories
58 Consumables & Attachments | 1" Impact Sockets
DEEP (cont'd)
S68H1-12L 1-1/2" 2.32 (59) 2.13 (54) 0.98 (25) 3.54 (90) C RR10015S
S68H1-916L 1-9/16" 2.4 (61) 2.13 (54) 0.98 (25) 3.54 (90) C RR10015S
S68H1-58L 1-5/8" 2.46 (62.5) 2.13 (54) 0.98 (25) 3.54 (90) C RR10015S
S68H1-1116L 1-11/16" 2.56 (65) 2.13 (54) 0.98 (25) 3.54 (90) C RR10015S
S68H1-34L 1-3/4" 2.66 (67.5) 2.37 (60.3) 1.22 (31) 3.94 (100) C RR10015S
S68H1-1316L 1-13/16" 2.72 (69) 2.37 (60.3) 1.22 (31) 3.94 (100) C RR10015S
S68H1-78L 1-7/8" 2.76 (70) 2.37 (60.3) 1.22 (31) 3.94 (100) C RR10015S
S68H1-1516L 1-15/16" 2.85 (72.5) 2.37 (60.3) 1.22 (31) 3.94 (100) C RR10015S
A B C S68H2L 2" 2.91 (74) 2.37 (60.3) 1.22 (31) 3.94 (100) C RR10015S
Impact Sockets
D1 S68H2-116L 2-1/16" 3.01 (76.5) 2.37 (60.3) 1.22 (31) 3.94 (100) C RR10015S
S68H2-18L 2-1/8" 3.11 (79) 2.37 (60.3) 1.22 (31) 4.25 (108) C RR10015S
T
S68H2-316L 2-3/16" 3.15 (80) 2.37 (60.3) 1.22 (31) 4.25 (108) C RR10015S
L
S68H2-14L 2-1/4" 3.25 (82.5) 2.37 (60.3) 1.42 (36) 4.25 (108) C RR10015S
S68H2-516L 2-5/16" 3.31 (84) 2.37 (60.3) 1.42 (36) 4.25 (108) C RR10015S
D2 S68H2-38L 2-3/8" 3.41 (86.5) 2.37 (60.3) 1.42 (36) 4.25 (108) C RR10015S
S68H2-716L 2-7/16" 3.5 (89) 2.37 (60.3) 1.42 (36) 4.25 (108) C RR10015S
D2 T L S68H2-12L 2-1/2" 3.6 (91.5) 2.37 (60.3) 1.42 (36) 4.72 (120) C RR10015S
S68H2-916L 2-9/16" 3.64 (92.5) 2.37 (60.3) 1.42 (36) 4.72 (120) C RR10015S
S68H2-58L 2-5/8" 3.74 (95) 2.37 (60.3) 1.73 (44) 4.72 (120) C RR10015S
S68H2-1116L 2-11/16" 3.8 (96.5) 2.37 (60.3) 1.73 (44) 4.72 (120) C RR10015S
S68H2-34L 2-3/4" 3.9 (99) 2.37 (60.3) 1.73 (44) 4.92 (125) C RR10015S
S68H2-1316L 2-13/16" 4 (101.5) 2.37 (60.3) 1.73 (44) 4.92 (125) C RR10015S
S68H2-78L 2-7/8" 4.04 (102.5) 2.37 (60.3) 1.73 (44) 4.92 (125) C RR10015S
S68H2-1516L 2-15/16" 4.11 (104.5) 2.37 (60.3) 1.73 (44) 4.92 (125) C RR10015S
S68H3L 3" 4.19 (106.5) 2.37 (60.3) 1.73 (44) 4.92 (125) C RR10015S
S68H3-18L 3-1/8" 4.39 (111.5) 2.37 (60.3) 1.73 (44) 4.92 (125) C RR10015S
S68H3-14L 3-1/4" 4.45 (113) 3.39 (86) 1.73 (44) 5.31 (135) C RR10025S
S68H3-38L 3-3/8" 4.53 (115) 3.39 (86) 2.2 (56) 5.31 (135) C RR10025S
S68H3-12L 3-1/2" 4.69 (119) 3.39 (86) 2.2 (56) 5.31 (135) C RR10025S
S68H3-58L 3-5/8" 5 (127) 3.39 (86) 2.2 (56) 5.51 (140) C RR10025S
S68H3-34L 3-3/4" 5.12 (130) 3.39 (86) 2.2 (56) 5.51 (140) C RR10025S
S68H3-78L 3-7/8" 5.35 (136) 3.74 (95) 2.2 (56) 5.51 (140) C RR10025S
S68H4L 4" 5.51 (140) 3.74 (95) 2.2 (56) 6.1 (155) C RR10025S
S68H4-18L 4-1/8" 5.63 (143) 3.74 (95) 2.4 (61) 6.1 (155) C RR10025S
S68H4-14L 4-1/4" 5.75 (146) 3.74 (95) 2.4 (61) 6.1 (155) C RR10025S
S68H4-38L 4-3/8" 5.87 (149) 3.74 (95) 2.4 (61) 6.1 (155) C RR10025S
S68H4-12L 4-1/2" 5.98 (152) 3.74 (95) 2.4 (61) 6.1 (155) C RR10025S
S68M19L 19 mm 1.38 (35) 2.13 (54) 0.98 (25) 3.54 (90) A RR10015S
S68M21L 21 mm 1.48 (37.5) 2.13 (54) 0.98 (25) 3.54 (90) A RR10015S
S68M22L 22 mm 1.54 (39) 2.13 (54) 0.98 (25) 3.54 (90) A RR10015S
59
DEEP (cont'd)
S68M23L 23 mm 1.57 (40) 2.13 (54) 0.98 (25) 3.54 (90) A RR10015S
S68M24L 24 mm 1.63 (41.5) 2.13 (54) 0.98 (25) 3.54 (90) A RR10015S
S68M25L 25 mm 1.67 (42.5) 2.13 (54) 0.98 (25) 3.54 (90) A RR10015S
S68M26L 26 mm 1.73 (44) 2.13 (54) 0.98 (25) 3.54 (90) A RR10015S
S68M27L 27 mm 1.77 (45) 2.13 (54) 0.98 (25) 3.54 (90) A RR10015S
S68M28L 28 mm 1.83 (46.5) 2.13 (54) 0.98 (25) 3.54 (90) A RR10015S
S68M29L 29 mm 1.87 (47.5) 2.13 (54) 0.98 (25) 3.54 (90) A RR10015S
S68M30L 30 mm 1.93 (49) 2.13 (54) 0.98 (25) 3.54 (90) A RR10015S
S68M31L 31 mm 1.97 (50) 2.13 (54) 0.98 (25) 3.54 (90) A RR10015S
Impact Sockets
S68M32L 32 mm 2.03 (51.5) 2.13 (54) 0.98 (25) 3.54 (90) A RR10015S
S68M33L 33 mm 2.07 (52.5) 2.13 (54) 0.98 (25) 3.54 (90) A RR10015S
S68M34L 34 mm 2.13 (54) 2.13 (54) 0.98 (25) 3.54 (90) B RR10015S
S68M35L 35 mm 2.17 (55) 2.13 (54) 0.98 (25) 3.54 (90) C RR10015S
S68M36L 36 mm 2.22 (56.5) 2.13 (54) 0.98 (25) 3.54 (90) C RR10015S
S68M37L 37 mm 2.28 (58) 2.13 (54) 0.98 (25) 3.54 (90) C RR10015S
S68M38L 38 mm 2.32 (59) 2.13 (54) 0.98 (25) 3.54 (90) C RR10015S
S68M40L 40 mm 2.4 (61) 2.13 (54) 0.98 (25) 3.54 (90) C RR10015S
S68M41L 41 mm 2.46 (62.5) 2.13 (54) 0.98 (25) 3.54 (90) C RR10015S
S68M42L 42 mm 2.52 (64) 2.13 (54) 0.98 (25) 3.54 (90) C RR10015S
S68M43L 43 mm 2.56 (65) 2.13 (54) 0.98 (25) 3.54 (90) C RR10015S
S68M45L 45 mm 2.66 (67.5) 2.13 (54) 1.18 (30) 3.94 (100) C RR10015S
S68M46L 46 mm 2.72 (69) 2.13 (54) 1.18 (30) 3.94 (100) C RR10015S
S68M48L 48 mm 2.81 (71.5) 2.13 (54) 1.18 (30) 3.94 (100) C RR10015S
S68M50L 50 mm 2.91 (74) 2.13 (54) 1.18 (30) 3.94 (100) C RR10015S
S68M52L 52 mm 3.01 (76.5) 2.13 (54) 1.18 (30) 3.94 (100) C RR10015S
S68M54L 54 mm 3.11 (79) 2.13 (54) 1.38 (35) 4.25 (108) C RR10015S
S68M55L 55 mm 3.15 (80) 2.13 (54) 1.38 (35) 4.25 (108) C RR10015S
S68M56L 56 mm 3.21 (81.5) 2.13 (54) 1.38 (35) 4.25 (108) C RR10015S
S68M58L 58 mm 3.31 (84) 2.13 (54) 1.38 (35) 4.25 (108) C RR10015S
S68M60L 60 mm 3.41 (86.5) 2.13 (54) 1.38 (35) 4.25 (108) C RR10015S
S68M65L 65 mm 3.64 (92.5) 2.13 (54) 1.38 (35) 4.72 (120) C RR10015S
S68M70L 70 mm 3.9 (99) 2.13 (54) 1.38 (35) 4.92 (125) C RR10015S
S68M75L 75 mm 4.13 (105) 2.37 (60.3) 1.38 (35) 4.92 (125) C RR10015S
S68M80L 80 mm 4.39 (111.5) 2.37 (60.3) 1.38 (35) 4.92 (125) C RR10015S
S68M85L 85 mm 4.53 (115) 3.39 (86) 1.38 (35) 5.31 (135) C RR10025S
S68M90L 90 mm 4.88 (124) 3.39 (86) 1.38 (35) 5.31 (135) C RR10025S
S68M95L 95 mm 5.12 (130) 3.39 (86) 1.38 (35) 5.51 (140) C RR10025S
ingersollrandproducts.com/accessories
60 Consumables & Attachments | 1" Impact Sockets
UNIVERSAL
S68H78U 7/8" 1.54 (39) 2.13 (54) 0.75 (19) 5 (127) A RR10015S
S68H1516U 15/16" 1.61 (41) 2.13 (54) 0.75 (19) 5.2 (132) A RR10015S
S68H1-116U 1-1/16" 1.77 (45) 2.13 (54) 0.75 (19) 5.2 (132) A RR10015S
D1
S68H1-18U 1-1/8" 1.89 (48) 2.13 (54) 0.75 (19) 5.2 (132) A RR10015S
T
S68H1-316U 1-3/16" 1.93 (49) 2.13 (54) 0.75 (19) 5.2 (132) A RR10015S
S68H1-14U 1-1/4" 2.01 (51) 2.13 (54) 0.75 (19) 5.2 (132) A RR10015S
L
S68H1-516U 1-5/16" 2.09 (53) 2.13 (54) 0.75 (19) 5.2 (132) A RR10015S
S68H1-38U 1-3/8" 2.17 (55) 2.13 (54) 0.75 (19) 5.2 (132) A RR10015S
S68H1-716U 1-7/16" 2.28 (58) 2.13 (54) 0.75 (19) 5.2 (132) A RR10015S
Impact Sockets
D2 S68H1-12U 1-1/2" 2.32 (59) 2.13 (54) 0.98 (25) 5.39 (137) A RR10015S
A
S68H1-916U 1-9/16" 2.4 (61) 2.13 (54) 0.98 (25) 5.39 (137) A RR10015S
S68H1-58U 1-5/8" 2.48 (63) 2.13 (54) 0.98 (25) 5.39 (137) A RR10015S
S68H1-1116U 1-11/16" 2.56 (65) 2.13 (54) 0.98 (25) 5.39 (137) A RR10015S
S68H1-34U 1-3/4" 2.64 (67) 2.13 (54) 0.98 (25) 5.39 (137) A RR10015S
S68H1-1316U 1-13/16" 2.72 (69) 2.13 (54) 1.06 (27) 5.59 (142) A RR10015S
S68H1-78U 1-7/8" 2.8 (71) 2.13 (54) 1.06 (27) 5.59 (142) A RR10015S
S68H1-1516U 1-15/16" 2.83 (72) 2.13 (54) 1.06 (27) 5.59 (142) A RR10015S
S68H2U 2" 2.99 (76) 2.13 (54) 1.06 (27) 5.59 (142) A RR10015S
S68M24U 24 mm 1.61 (41) 2.13 (54) 0.67 (17) 5.2 (132) A RR10015S
S68M26U 26 mm 1.73 (44) 2.13 (54) 0.67 (17) 5.2 (132) A RR10015S
S68M27U 27 mm 1.77 (45) 2.13 (54) 0.67 (17) 5.2 (132) A RR10015S
S68M29U 29 mm 1.89 (48) 2.13 (54) 0.67 (17) 5.2 (132) A RR10015S
S68M30U 30 mm 1.93 (49) 2.13 (54) 0.67 (17) 5.2 (132) A RR10015S
S68M32U 32 mm 2.01 (51) 2.13 (54) 0.87 (22) 5.2 (132) A RR10015S
S68M33U 33 mm 2.09 (53) 2.13 (54) 0.87 (22) 5.2 (132) A RR10015S
S68M34U 34 mm 2.13 (54) 2.13 (54) 0.87 (22) 5.2 (132) A RR10015S
S68M35U 35 mm 2.17 (55) 2.13 (54) 0.87 (22) 5.2 (132) A RR10015S
S68M36U 36 mm 2.2 (56) 2.13 (54) 0.87 (22) 5.2 (132) A RR10015S
S68M38U 38 mm 2.32 (59) 2.13 (54) 0.98 (25) 5.39 (137) A RR10015S
S68M41U 41 mm 2.48 (63) 2.13 (54) 0.98 (25) 5.39 (137) A RR10015S
S68M42U 42 mm 2.52 (64) 2.13 (54) 0.98 (25) 5.39 (137) A RR10015S
S68M43U 43 mm 2.56 (65) 2.13 (54) 0.98 (25) 5.39 (137) A RR10015S
S68M44U 44 mm 2.64 (67) 2.13 (54) 0.98 (25) 5.39 (137) A RR10015S
S68M45U 45 mm 2.68 (68) 2.13 (54) 1.06 (27) 5.59 (142) A RR10015S
S68M46U 46 mm 2.72 (69) 2.13 (54) 1.06 (27) 5.59 (142) A RR10015S
S68M47U 47 mm 2.76 (70) 2.13 (54) 1.06 (27) 5.59 (142) A RR10015S
S68M48U 48 mm 2.8 (71) 2.13 (54) 1.06 (27) 5.59 (142) A RR10015S
S68M50U 50 mm 2.91 (74) 2.13 (54) 1.06 (27) 5.59 (142) A RR10015S
61
Accessories
Recommended
Description Output Size Retaining Ring
A8F12Mp- 1-1/2"
1" female to 1-1/2" male adapter RR10015S
tion
Impact Sockets
E87H 7" Extension 1" RR10015S Extension
ingersollrandproducts.com/accessories
Ø D1
T
L
62
Ø D2
STANDARD
S612H1-316 1-3/16" 2.2 (56) 3.39 (86) 0.83 (21) 3.07 (78) A RR10025S
S612H1-14 1-1/4" 2.28 (58) 3.39 (86) 0.87 (22) 3.07 (78) A RR10025S
S612H1-516 1-5/16" 2.36 (60) 3.39 (86) 0.87 (22) 3.07 (78) A RR10025S
S612H1-38 1-3//8" 2.52 (64) 3.39 (86) 0.87 (22) 3.07 (78) A RR10025S
S612H1-716 1-7/16" 2.52 (64) 3.39 (86) 0.94 (24) 3.07 (78) A RR10025S
Impact Sockets
S612H1-12 1-1/2" 2.6 (66) 3.39 (86) 1.02 (26) 3.15 (80) A RR10025S
S612H1-916 1-9⁄16" 2.68 (68) 3.39 (86) 1.1 (28) 3.15 (80) A RR10025S
S612H1-58 1-5/8" 2.76 (70)D1 3.39 (86) 1.1 (28) 3.15 (80) A RR10025S
D1
D1
S612H1-1116 1-11/16" 2.87 (73) 3.39 (86) 1.1 (28) 3.23 (82) A RR10025S
S612H1-34 1-3/4" 2.95 (75) 3.39 (86) 1.18 (30) 3.31 (84) A RR10025S
T T
T
S612H1-1316 1-13/16" 2.99 (76) 3.39 (86) 1.18 (30) 3.31 (84) A RR10025S
L L L
S612H1-78 1-7/8" 3.07 (78) 3.39 (86) 1.26 (32) 3.43 (87) A RR10025S
A
S612H1-1516 1-15⁄16" 3.15 (80) 3.39 (86) 1.26 (32) 3.43 (87) A RR10025S
S612H2 2" 3.23 (82) 3.39 (86) 1.26 (32) 3.43 (87) A RR10025S
D2 D2 D2
S612H2-116 2-1⁄16" 3.27 (83) 3.39 (86) 1.34 (34) 3.43 (87) A RR10025S
S612H2-18D1 2-1⁄8" 3.39 (86) 3.39 (86) 1.46 (37) 3.54 (90) B RR10025S
D1
D1
S612H2-316 2-3⁄16" 3.46 (88) 3.39 (86) 1.46 (37) 3.54 (90) C RR10025S
S612H2-14 2-1⁄4" 3.54 (90) 3.39 (86) 1.54 (39) 3.74 (95) C RR10025S
T
T
S612H2-516 2-5⁄16" 3.66 (93) 3.39 (86) 1.54 (39) 3.74 (95) C RR10025S
L L L
S612H2-38 2-3⁄8" 3.7 (94) 3.39 (86) 1.54 (39) 3.74 (95) C RR10025S
B S612H2-716 2-7⁄16" 3.78 (96) 3.39 (86) 1.65 (42) 3.94 (100) C RR10025S
S612H2-12 2-1⁄2" 3.86 (98) 3.39 (86) 1.65 (42) 3.94 (100) C RR10025S
D2 D2 D2
S612H2-916 2-9⁄16" 3.94 (100) 3.39 (86) 1.65 (42) 3.94 (100) C RR10025S
S612H2-58 2-5⁄8" 4.02 (102) 3.39 (86) 1.81 (46) 4.13 (105) C RR10025S
D1
D1 S612H2-1116 2-11⁄16" 4.09 (104) 3.39 (86) 1.81 (46) 4.13 (105) C RR10025S
S612H2-34 2-3⁄4" 4.17 (106) 3.39 (86) 1.81 (46) 4.13 (105) C RR10025S
T S612H2-1316 2-13⁄16" 4.25 (108) 3.39 (86) 1.93 (49) 4.25 (108) C RR10025S
L L
S612H2-78 2-7⁄8" 4.33 (110) 3.39 (86) 1.93 (49) 4.25 (108) C RR10025S
C S612H2-1516 2-15⁄16" 4.41 (112) 3.39 (86) 1.93 (49) 4.25 (108) C RR10025S
S612H3 3" 4.45 (113) 3.39 (86) 1.93 (49) 4.25 (108) C RR10025S
D2 D2
S612H3-116 3-1⁄16" 4.53 (115) 3.39 (86) 2.09 (53) 4.53 (115) C RR10025S
S612H3-18 3-1⁄8" 4.65 (118) 3.39 (86) 2.09 (53) 4.53 (115) C RR10025S
S612H3-316 3-3⁄16" 4.72 (120) 3.39 (86) 2.09 (53) 4.53 (115) C RR10025S
S612H3-14 3-1⁄4" 4.8 (122) 3.39 (86) 2.09 (53) 4.53 (115) C RR10025S
S612H3-516 3-5⁄16" 4.88 (124) 3.39 (86) 2.2 (56) 4.65 (118) C RR10025S
63
STANDARD (cont'd)
S612H3-38 3-3⁄8" 4.96 (126) 3.39 (86) 2.2 (56) 4.65 (118) C RR10025S
S612H3-716 3-7⁄16" 5.04 (128) 3.39 (86) 2.2 (56) 4.65 (118) C RR10025S
S612H3-12 3-1⁄2" 5.08 (129) 3.39 (86) 2.32 (59) 4.84 (123) C RR10025S
S612H3-916 3-9⁄16" 5.16 (131) 3.39 (86) 2.32 (59) 4.84 (123) C RR10025S
S612H3-58 3-5⁄8" 5.24 (133) 3.39 (86) 2.32 (59) 4.84 (123) C RR10025S
S612H3-1116 3-11⁄16" 5.31 (135) 3.39 (86) 2.4 (61) 4.84 (123) C RR10025S
S612H3-34 3-3⁄4" 5.39 (137) 3.74 (95) 2.4 (61) 4.84 (123) C RR10025S
S612H3-1316 3-13⁄16" 5.39 (137) 3.74 (95) 2.56 (65) 5.12 (130) C RR10025S
S612H3-78 3-7⁄8" 5.67 (144) 3.74 (95) 2.56 (65) 5.12 (130) C RR10025S
Impact Sockets
S612H3-1516 3-15⁄16" 5.67 (144) 3.74 (95) 2.56 (65) 5.12 (130) C RR10025S
S612H4 4" 5.79 (147) 3.74 (95) 2.56 (65) 5.12 (130) C RR10025S
S612H4-116 4-1⁄16" 5.79 (147) 3.74 (95) 2.68 (68) 5.12 (130) C RR10025S
S612H4-18 4-1⁄8" 6.06 (154) 3.74 (95) 2.68 (68) 5.12 (130) C RR10025S
S612H4-316 4-3/16" 6.06 (154) 3.74 (95) 2.68 (68) 5.12 (130) C RR10025S
S612H4-14 4-1⁄4" 6.06 (154) 3.74 (95) 2.83 (72) 5.31 (135) C RR10025S
S612H4-516 4-5⁄16" 6.18 (157) 3.74 (95) 2.83 (72) 5.31 (135) C RR10025S
S612H4-38 4-3⁄8" 6.18 (157) 3.74 (95) 2.83 (72) 5.31 (135) C RR10025S
S612H4-716 4-7⁄16" 6.18 (157) 3.74 (95) 2.83 (72) 5.31 (135) C RR10025S
S612H4-12 4-1/2" 6.46 (164) 3.74 (95) 3.03 (77) 5.51 (140) C RR10025S
S612H4-58 4-5⁄8" 6.46 (164) 3.74 (95) 3.03 (77) 5.51 (140) C RR10025S
S612H4-34 4-3⁄4" 6.57 (167) 3.74 (95) 3.03 (77) 5.51 (140) C RR10025S
S612M30 30 mm 2.2 (56) 3.39 (86) 0.83 (21) 3.07 (78) A RR10025S
S612M32 32 mm 2.28 (58) 3.39 (86) 0.87 (22) 3.07 (78) A RR10025S
S612M35 35 mm 2.52 (64) 3.39 (86) 0.87 (22) 3.07 (78) A RR10025S
S612M36 36 mm 2.52 (64) 3.39 (86) 0.94 (24) 3.07 (78) A RR10025S
S612M38 38 mm 2.6 (66) 3.39 (86) 1.02 (26) 3.15 (80) A RR10025S
S612M41 41 mm 2.76 (70) 3.39 (86) 1.1 (28) 3.15 (80) A RR10025S
S612M46 46 mm 2.99 (76) 3.39 (86) 1.18 (30) 3.31 (84) A RR10025S
S612M50 50 mm 3.19 (81) 3.39 (86) 1.26 (32) 3.43 (87) A RR10025S
S612M54 54 mm 3.39 (86) 3.39 (86) 1.46 (37) 3.54 (90) B RR10025S
S612M55 55 mm 3.43 (87) 3.39 (86) 1.46 (37) 3.54 (90) C RR10025S
S612M58 58 mm 3.62 (92) 3.39 (86) 1.54 (39) 3.74 (95) C RR10025S
S612M60 60 mm 3.7 (94) 3.39 (86) 1.54 (39) 3.74 (95) C RR10025S
S612M62 62 mm 3.78 (96) 3.39 (86) 1.65 (42) 3.94 (100) C RR10025S
S612M65 65 mm 3.94 (100) 3.39 (86) 1.65 (42) 3.94 (100) C RR10025S
S612M68 68 mm 4.09 (104) 3.39 (86) 1.81 (46) 4.13 (105) C RR10025S
S612M70 70 mm 4.17 (106) 3.39 (86) 1.81 (46) 4.13 (105) C RR10025S
S612M73 73 mm 4.33 (110) 3.39 (86) 1.93 (49) 4.25 (108) C RR10025S
S612M75 75 mm 4.41 (112) 3.39 (86) 1.93 (49) 4.25 (108) C RR10025S
ingersollrandproducts.com/accessories
64 Consumables & Attachments | 1-1/2" Impact Sockets
STANDARD (cont'd)
S612M78 78 mm 4.53 (115) 3.39 (86) 2.09 (53) 4.53 (115) C RR10025S
S612M80 80 mm 4.69 (119) 3.39 (86) 2.09 (53) 4.53 (115) C RR10025S
S612M85 85 mm 4.92 (125) 3.39 (86) 2.2 (56) 4.65 (118) C RR10025S
S612M90 90 mm 5.16 (131) 3.39 (86) 2.32 (59) 4.84 (123) C RR10025S
S612M95 95 mm 5.39 (137) 3.74 (95) 2.4 (61) 4.84 (123) C RR10025S
S612M100 100 mm 5.67 (144) 3.74 (95) 2.56 (65) 5.12 (130) C RR10025S
S612M105 105 mm 6.06 (154) 3.74 (95) 2.68 (68) 5.12 (130) C RR10025S
S612M110 110 mm 6.18 (157) 3.74 (95) 2.83 (72) 5.31 (135) C RR10025S
S612M115 115 mm 6.46 (164) 3.74 (95) 3.03 (77) 5.51 (140) C RR10025S
Impact Sockets
S612M120 120 mm 6.57 (167) 3.74 (95) 3.03 (77) 5.51 (140) C RR10025S
S612M125 125 mm 6.85 (174) 5 (127) 3.03 (77) 5.51 (140) C RR10035S
DEEP
S612H1-58L 1-5⁄8" 2.76 (70) 3.39 (86) 1.1 (28) 4.53 (115) A RR10025S
S612H1-1116L 1-11⁄16" 2.87 (73) 3.39 (86) 1.1 (28) 4.53 (115) A RR10025S
S612H1-34L 1-3/4" 2.95 (75) 3.39 (86) 1.18 (30) 4.53 (115) A RR10025S
S612H1-1316L 1-13/16" 2.99 (76) 3.39 (86) 1.18 (30) 4.53 (115) A RR10025S
S612H1-78L 1-7/8" 3.07 (78) 3.39 (86) 1.26 (32) 4.53 (115) A RR10025S
S612H1-1516L 1-15⁄16" 3.15 (80) D1 3.39 (86) 1.26 (32) 4.53 (115) A RR10025S
D1
D1 S612H2L 2" 3.23 (82) 3.39 (86) 1.34 (34) 5.31 (135) A RR10025S
S612H2-116L 2-1⁄16" 3.27 (83) 3.39 (86) 1.34 (34) 5.51 (140) A RR10025S
T T
T S612H2-18L 2-1/8" 3.39 (86) 3.39 (86) 1.46 (37) 5.51 (140) B RR10025S
L L L
S612H2-316L 2-3⁄16" 3.46 (88) 3.39 (86) 1.46 (37) 5.51 (140) C RR10025S
A S612H2-14L 2-1⁄4" 3.54 (90) 3.39 (86) 1.54 (39) 5.91 (150) C RR10025S
S612H2-516L 2-5⁄16" 3.66 (93) 3.39 (86) 1.54 (39) 5.91 (150) C RR10025S
D2 D2 D2
S612H2-38L 2-3⁄8" 3.7 (94) 3.39 (86) 1.54 (39) 5.91 (150) C RR10025S
D1
D1
D1 S612H2-716L 2-7⁄16" 3.78 (96) 3.39 (86) 1.65 (42) 5.91 (150) C RR10025S
S612H2-12L 2-1⁄2" 3.86 (98) 3.39 (86) 1.65 (42) 5.91 (150) C RR10025S
T
S612H2-916L
T 2-9⁄16" 3.94 (100) 3.39 (86) 1.65 (42) 5.91 (150) C RR10025S
L L S612H2-58L 2-5⁄8" L 4.02 (102) 3.39 (86) 1.81 (46) 5.91 (150) C RR10025S
S612H2-1116L 2-11⁄16" 4.09 (104) 3.39 (86) 1.81 (46) 5.91 (150) C RR10025S
B
S612H2-34L 2-3⁄4" 4.17 (106) 3.39 (86) 1.81 (46) 6.3 (160) C RR10025S
D2 D2 S612H2-1316L
D2 2-13⁄16" 4.25 (108) 3.39 (86) 1.93 (49) 6.3 (160) C RR10025S
S612H2-78L 2-7⁄8" 4.33 (110) 3.39 (86) 1.93 (49) 6.3 (160) C RR10025S
D1
D1 S612H2-1516L 2-15⁄16" 4.41 (112) 3.39 (86) 1.93 (49) 6.69 (170) C RR10025S
S612H3L 3" 4.45 (113) 3.39 (86) 1.93 (49) 6.69 (170) C RR10025S
T
S612H3-116L 3-1⁄16" 4.53 (115) 3.39 (86) 2.09 (53) 6.69 (170) C RR10025S
L L
S612H3-18L 3-1⁄8" 4.65 (118) 3.39 (86) 2.09 (53) 6.69 (170) C RR10025S
C S612H3-38L 3-3⁄8" 4.96 (126) 3.39 (86) 2.2 (56) 6.69 (170) C RR10025S
S612H3-12L 3-1⁄2" 5.08 (129) 3.39 (86) 2.32 (59) 6.69 (170) C RR10025S
D2 D2
S612H3-916L 3-9⁄16" 5.16 (131) 3.39 (86) 2.32 (59) 6.69 (170) C RR10025S
65
DEEP (cont'd)
S612H3-34L 3-3⁄4" 5.39 (137) 3.74 (95) 2.4 (61) 7.09 (180) C RR10025S
S612H3-78L 3-7⁄8" 5.67 (144) 3.74 (95) 2.56 (65) 7.09 (180) C RR10025S
S612H3-1516L 3-15⁄16" 5.67 (144) 3.74 (95) 2.56 (65) 7.48 (190) C RR10025S
S612H4L 4" 5.79 (147) 3.74 (95) 2.56 (65) 7.48 (190) C RR10025S
S612H4-116L 4-1⁄16" 5.79 (147) 3.74 (95) 2.68 (68) 7.48 (190) C RR10025S
S612H4-18L 4-1⁄8" 6.06 (154) 3.74 (95) 2.68 (68) 7.48 (190) C RR10025S
S612H4-316L 4-3/16" 6.06 (154) 3.74 (95) 2.68 (68) 7.48 (190) C RR10025S
S612H4-14L 4-1⁄4" 6.06 (154) 3.74 (95) 2.83 (72) 7.48 (190) C RR10025S
S612H4-516L 4-5⁄16" 6.18 (157) 3.74 (95) 2.83 (72) 7.87 (200) C RR10025S
Impact Sockets
S612H4-38L 4-3⁄8" 6.18 (157) 3.74 (95) 2.83 (72) 7.87 (200) C RR10025S
S612H4-716L 4-7/16" 6.18 (157) 3.74 (95) 2.83 (72) 7.87 (200) C RR10025S
S612H4-12L 4-1/2" 6.46 (164) 3.74 (95) 3.03 (77) 8.27 (210) C RR10025S
S612H4-58L 4-5⁄8" 6.46 (164) 3.74 (95) 3.03 (77) 8.27 (210) C RR10025S
S612H4-34L 4-3⁄4" 6.57 (167) 3.74 (95) 3.03 (77) 8.27 (210) C RR10025S
S612M41L 41 mm 2.76 (70) 3.39 (86) 1.1 (28) 4.53 (115) A RR10025S
S612M46L 46 mm 2.99 (76) 3.39 (86) 1.18 (30) 4.53 (115) A RR10025S
S612M50L 50 mm 3.19 (81) 3.39 (86) 1.34 (34) 5.31 (135) A RR10025S
S612M54L 54 mm 3.39 (86) 3.39 (86) 1.46 (37) 5.51 (140) B RR10025S
S612M55L 55 mm 3.43 (87) 3.39 (86) 1.46 (37) 5.51 (140) C RR10025S
S612M57L 57 mm 3.54 (90) 3.39 (86) 1.54 (39) 5.91 (150) C RR10025S
S612M60L 60 mm 3.7 (94) 3.39 (86) 1.54 (39) 5.91 (150) C RR10025S
S612M62L 62 mm 3.78 (96) 3.39 (86) 1.65 (42) 5.91 (150) C RR10025S
S612M65L 65 mm 3.94 (100) 3.39 (86) 1.65 (42) 5.91 (150) C RR10025S
S612M70L 70 mm 4.17 (106) 3.39 (86) 1.81 (46) 6.3 (160) C RR10025S
S612M73L 73 mm 4.33 (110) 3.39 (86) 1.93 (49) 6.3 (160) C RR10025S
S612M75L 75 mm 4.41 (112) 3.39 (86) 1.93 (49) 6.69 (170) C RR10025S
S612M76L 76 mm 4.45 (113) 3.39 (86) 1.93 (49) 6.69 (170) C RR10025S
S612M78L 78 mm 4.53 (115) 3.39 (86) 2.09 (53) 6.69 (170) C RR10025S
S612M80L 80 mm 4.69 (119) 3.39 (86) 2.09 (53) 6.69 (170) C RR10025S
S612M85L 85 mm 4.92 (125) 3.39 (86) 2.2 (56) 6.69 (170) C RR10025S
S612M90L 90 mm 5.16 (131) 3.39 (86) 2.32 (59) 6.69 (170) C RR10025S
S612M95L 95 mm 5.39 (137) 3.74 (95) 2.4 (61) 7.09 (180) C RR10025S
S612M100L 100 mm 5.67 (144) 3.74 (95) 2.56 (65) 7.48 (190) C RR10025S
S612M105L 105 mm 6.06 (154) 3.74 (95) 2.68 (68) 7.48 (190) C RR10025S
S612M110L 110 mm 6.18 (157) 3.74 (95) 2.83 (72) 7.87 (200) C RR10025S
S612M115L 115 mm 6.46 (164) 3.74 (95) 3.03 (77) 8.27 (210) C RR10025S
S612M120L 120 mm 6.57 (167) 3.74 (95) 3.03 (77) 8.27 (210) C RR10025S
ingersollrandproducts.com/accessories
66 Consumables & Attachments | 1-1/2" Impact Sockets
Accessories
Recommended
Description Output Size Retaining Ring
A12F20Mp-
1-1/2" female to 2-1/2" male adapter 2-1/2" RR10025S
tion
67
Ø D2
STANDARD
S620H3 3" 4.72 (120) 5 (127) 1.77 (45) 5.51 (140) A RR10035S
S620H3-18 3-1/8" 4.88 (124) 5 (127) 1.77 (45) 5.51 (140) A RR10035S
S620H3-14 3-1⁄4" 5 (127) 5 (127) 1.77 (45) 5.51 (140) B RR10035S
S620H3-38 3-3⁄8" 5.16 (131) 5 (127) 2.05 (52) 5.51 (140) C RR10035S
S620H3-12 3-1/2" 5.31 (135) 5 (127) 2.05 (52) 5.51 (140) C RR10035S
S620H3-58 3-5/8" 5.47 (139) 5 (127) 2.05 (52) 5.71 (145) C RR10035S
S620H3-34 3-3/4" 5.63 (143) 5 (127) 2.05 (52) 5.71 (145) C RR10035S
S620H3-78 3-7/8" 5.79 (147) 5 (127) 2.28 (58) 5.91 (150) C RR10035S
S620H4D1 4" 5.94 (151) D1 5 (127) 2.28 (58) 5.91 (150) C RR10035S
D1
S620H4-18 4-1/8" 6.1 (155) 5 (127) 2.28 (58) 6.1 (155) C RR10035S
S620H4-14 4-1/4" 6.26
T
(159) 5 (127) 2.36 (60) 6.3 (160) C RR10035S
T
T
S620H4-38 4-3/8" 6.42 (163) 5 (127) L 2.44 (62) 6.5 (165) C RR10035S
L L
S620H4-12 4-1/2" 6.57 (167) 5 (127) 2.44 (62) 6.5 (165) C RR10035S
A S620H4-58 4-5/8" 6.77 (172) 5 (127) 2.64 (67) 6.69 (170) C RR10035S
S620H4-34 4-3/4" 6.93 (176) 5 (127) 2.64 (67) 6.69 (170) C RR10035S
D2 D2 D2
S620H4-78 4-7/8" 7.24 (184) 5 (127) 2.83 (72) 6.89 (175) C RR10035S
S620H5 D1 5" 7.24 (184) 5 (127) 2.83 (72) 6.89 (175) C RR10035S
D1
D1
S620H5-18 5-1/8" 7.36 (187) 5.98 (152) 2.83 (72) 6.89 (175) C 588-216 & 588-215
S620H5-14
T
5-1/4" 7.64 (194) 5.98 (152) 2.83 (72) 6.89 (175) C 588-216 & 588-215
T
S620H5-38 5-3/8" L 7.76 (197) 5.98 (152) 3.03 (77) 7.09 (180) C 588-216 & 588-215
L L
S620H5-12 5-1/2" 8.03 (204) 5.98 (152) 3.03 (77) 7.09 (180) C 588-216 & 588-215
S620H5-58 5-5/8" 8.15 (207) 5.98 (152) 3.27 (83) 7.28 (185) C 588-216 & 588-215
B S620H5-34 5-3/4" 8.43 (214) 5.98 (152) 3.27 (83) 7.28 (185) C 588-216 & 588-215
D2 D2 D2
S620H5-78 5-7/8" 8.43 (214) 5.98 (152) 3.27 (83) 7.28 (185) C 588-216 & 588-215
S620H6 6" 8.54 (217) 5.98 (152) 3.27 (83) 7.28 (185) C 588-216 & 588-215
D1
D1 S620H6-18 6-1/8" 8.82 (224) 5.98 (152) 3.54 (90) 7.48 (190) C 588-216 & 588-215
S620H6-14 6-1/4" 8.94 (227) 5.98 (152) 3.54 (90) 7.48 (190) C 588-216 & 588-215
T
S620H6-38 6-3/8" 9.21 (234) 5.98 (152) 3.74 (95) 7.68 (195) C 588-216 & 588-215
L L
S620H6-12 6-1/2" 9.21 (234) 5.98 (152) 3.74 (95) 7.68 (195) C 588-216 & 588-215
S620H6-58 6-5/8" 9.33 (237) 5.98 (152) 3.74 (95) 7.68 (195) C 588-216 & 588-215
S620H6-34 6-3/4" 9.61 (244) 5.98 (152) 3.74 (95) 7.68 (195) C 588-216 & 588-215
D2
D2 C S620H6-78 6-7/8" 9.72 (247) 5.98 (152) 3.94 (100) 7.87 (200) C 588-216 & 588-215
S620H7 7" 10 (254) 5.98 (152) 3.94 (100) 7.87 (200) C 588-216 & 588-215
S620H7-12 7-1/2" 10.39 (264) 5.98 (152) 4.13 (105) 8.27 (210) C 588-216 & 588-215
S620H7-58 7-5/8" 10.51 (267) 5.98 (152) 4.13 (105) 8.27 (210) C 588-216 & 588-215
ingersollrandproducts.com/accessories
68 Consumables & Attachments | 2-1/2" Impact Sockets
Recommended
6-PT Part Output D1 D2 T L Retaining Ring
Number Size in (mm) in (mm) in (mm) in (mm) Type or O-Ring / Pin
STANDARD (cont'd)
S620H7-78 7-7/8" 10.79 (274) 5.98 (152) 4.33 (110) 8.66 (220) C 588-216 & 588-215
S620H8 8" 10.91 (277) 5.98 (152) 4.33 (110) 8.66 (220) C 588-216 & 588-215
S620M75 75 mm 4.65 (118) 5 (127) 1.65 (42) 5.51 (140) A RR10035S
S620M76 76 mm 4.8 (122) 5 (127) 1.77 (45) 5.51 (140) A RR10035S
S620M80 80 mm 4.88 (124) 5 (127) 1.77 (45) 5.51 (140) B RR10035S
S620M85 85 mm 5.12 (130) 5 (127) 2.05 (52) 5.51 (140) C RR10035S
S620M90 90 mm 5.35 (136) 5 (127) 2.05 (52) 5.71 (145) C RR10035S
S620M95 95 mm 5.63 (143) 5 (127) 2.05 (52) 5.71 (145) C RR10035S
S620M100 100 mm 5.87 (149) 5 (127) 2.28 (58) 5.91 (150) C RR10035S
Impact Sockets
S620M105 105 mm 6.1 (155) 5 (127) 2.28 (58) 6.1 (155) C RR10035S
S620M110 110 mm 6.34 (161) 5 (127) 2.36 (60) 6.3 (160) C RR10035S
S620M115 115 mm 6.57 (167) 5 (127) 2.44 (62) 6.5 (165) C RR10035S
S620M120 120 mm 6.93 (176) 5 (127) 2.64 (67) 6.69 (170) C RR10035S
S620M125 125 mm 7.24 (184) 5 (127) 2.83 (72) 6.89 (175) C RR10035S
S620M130 130 mm 7.36 (187) 5.98 (152) 2.83 (72) 6.89 (175) C 588-216 & 588-215
S620M135 135 mm 7.64 (194) 5.98 (152) 3.03 (77) 7.09 (180) C 588-216 & 588-215
S620M140 140 mm 8.03 (204) 5.98 (152) 3.03 (77) 7.09 (180) C 588-216 & 588-215
S620M145 145 mm 8.15 (207) 5.98 (152) 3.27 (83) 7.28 (185) C 588-216 & 588-215
S620M150 150 mm 8.43 (214) 5.98 (152) 3.27 (83) 7.28 (185) C 588-216 & 588-215
S620M155 155 mm 8.82 (224) 5.98 (152) 3.54 (90) 7.48 (190) C 588-216 & 588-215
S620M160 160 mm 8.94 (227) 5.98 (152) 3.54 (90) 7.48 (190) C 588-216 & 588-215
S620M165 165 mm 9.21 (234) 5.98 (152) 3.74 (95) 7.68 (195) C 588-216 & 588-215
S620M170 170 mm 9.61 (244) 5.98 (152) 3.74 (95) 7.68 (195) C 588-216 & 588-215
S620M175 175 mm 9.72 (247) 5.98 (152) 3.94 (100) 7.87 (200) C 588-216 & 588-215
S620M180 180 mm 10 (254) 5.98 (152) 3.94 (100) 7.87 (200) C 588-216 & 588-215
S620M185 185 mm 10.12 (257) 5.98 (152) 4.13 (105) 8.27 (210) C 588-216 & 588-215
S620M190 190 mm 10.39 (264) 5.98 (152) 4.13 (105) 8.27 (210) C 588-216 & 588-215
S620M200 200 mm 10.79 (274) 5.98 (152) 4.33 (110) 8.66 (220) C 588-216 & 588-215
Accessories
Recommended
Description Output Size Retaining Ring
69
Ø D2
STANDARD
S65SH1-116 1-1/16" 1.89 (48) 2.17 (55) 0.94 (24) 3.15 (80) A
S65SH1-118 1-1/8" 1.89 (48) 2.17 (55) 0.94 (24) 3.15 (80) A
S65SH1-114 1-1/4" 2.17 (55) 2.17 (55) 0.94 (24) 3.15 (80) B
S65SM33 33 mm 2.17 (55) 2.17 (55) 0.94 (24) 3.15 (80) B
S65SM35 35 mm 2.24 (57) 2.17 (55) 0.94 (24) 3.15 (80) C
Impact Sockets
D1 D1 D1 D1 D1 D1 D1 D1 D1
S65SM38 38 mm 2.36 (60) 2.17 (55) 0.94 (24) 3.15 (80) C
T T T T T T
S65SM41 41 mm 2.64 (67) 2.17 (55) 0.94 (24) 3.15 (80) C
T T T
S65SH1-34 1-3/4" 2.87 (73) 2.56 (65) 1.5 (38) 3.15 (80) C
L L L L L L L L
S65SH1-12
L 1-1/2" 2.36 (60) 2.17 (55) 0.94 (24) 3.15 (80) C
S65SH78 7/8" 1.73 (44) 2.17 (55) 0.94 (24) 3.15 (80) A
S65SH1516 15/16" 1.73 (44) 2.17 (55) 0.94 (24) 3.15 (80) A
D2 D2 D2 D2 D2 D2 D2 D2 D2 S65SH1 1" 1.81 (46) 2.17 (55) 0.94 (24) 3.15 (80) A
A B C
S65SH1-316 1-3/16" 2.01 (51) 2.17 (55) 0.94 (24) 3.15 (80) A
4-PT
STANDARD
S45SM17 17 mm 1.73 (44) 2.17 (55) 0.94 (24) 3.15 (80) A
S45SM21 21 mm 1.73 (44) 2.17 (55) 0.94 (24) 3.15 (80) A
S45SH1316 13/16" 1.73 (44) 2.17 (55) 0.94 (24) 3.15 (80) A
S45SH1516 15/16" 1.73 (44) 2.17 (55) 0.94 (24) 3.15 (80) A
ingersollrandproducts.com/accessories
70 Consumables & Attachments | Retaining Rings
Retaining Rings
Internal
Part Number Quantity in (mm) Material
RR10001 10 3/5" (15) Plastic
Dimensions Weight
Part Number Description (H x W x D) (lb)
Impact Sockets
3/8" Drive combo 32
SD-38C 22" x 24" x 16"
impact sockets
ingersollrandproducts.com/accessories
72
Sets
Moil Point Hex Shank Size 7/8" x 3-1/4" 1" x 4-1/4" 1-1/8" x 6" 1-1/4" x 6"
Length Part Weight Part Weight Part Weight Part Weight
Under Collar Number lb Number lb Number lb Number lb
ingersollrandproducts.com/accessories
74 Consumables & Attachments | Pneumatic Tool Steels & Accessories
1" Narrow Hex Shank Size 7/8" x 3-1/4" 1" x 4-1/4" 1-1/8" x 6" 1-1/4" x 6"
Chisel Length Part Weight Part Weight Part Weight Part Weight
Under Collar Number lb Number lb Number lb Number lb
1" Narrow ChiselS — Standard-duty
14" 50199207 3.25 50197805 4.5 50197904 6 50196385 7.5
General demolition
18" 50199215 4 50197821 5.5 50197912 7.25 50196401 9
24" 50199223 5.25 45510245 6.75 50197938 9.5 50196419 11.25
36" 45510682 7.5 45510252 10 51298107 13.25 51299477 15.75
48" 45510690 9.75 45510260 13 50197979 17 51299485 20.5
60" 45510708 12 45510278 15.75 50197987 20.5 51299048 25
72" 45510716 14.25 45510286 18.75 50197995 24 51299493 29.5
84" – – 45510294 21.75 45510385 28 45509965 34
96" – – 45510302 24.5 45510393 31.75 45509973 38.75
Pneumatic Tool Steels
3" Chisel Hex Shank Size 7/8" x 3-1/4" 1" x 4-1/4" 1-1/8" x 6" 1-1/4" x 6"
Length Part Weight Part Weight Part Weight Part Weight
Under Collar Number lb Number lb Number lb Number lb
3" ChiselS
Concrete demolition
and asphalt cutting 14" 50195288 3.25 50195320 4.5 50114883 6 50193879 7.5
18" 50195296 4 50195338 5.5 50193754 7.25 50193887 9
24" 45510542 5.5 50195353 6.75 50193747 9.75 50193903 12.25
36" 45510559 8 50195361 10 45510500 13.5 45510484 16.75
48" 45510567 10 50195379 12.75 45510518 17.25 50193937 21.25
60" 45510575 12.25 45510476 16.5 45510526 21 45510492 26
72" 45510583 14 51304574 19.25 45510534 24.75 50191790 30
1-1/2" Super Hex Shank Size 7/8" x 3-1/4" 1" x 4-1/4" 1-1/8" x 6" 1-1/4" x 6"
Cut Chisel Length Part Weight Part Weight Part Weight Part Weight
Under Collar Number lb Number lb Number lb Number lb
1-1/2" Super Cut Chisel
3-3/4" Combo Hex Shank Size 7/8" x 3-1/4" 1" x 4-1/4" 1-1/8" x 6" 1-1/4" x 6"
Cutter Length Part Weight Part Weight Part Weight Part Weight
Under Collar Number lb Number lb Number lb Number lb
3-3/4" Combo Cutter
Great for manhole 12" – – – – 22040612 8.5 22040620 9.5
reconstruction
5" Asphalt Hex Shank Size 7/8" x 3-1/4" 1" x 4-1/4" 1-1/8" x 6" 1-1/4" x 6"
Cutter Length Part Weight Part Weight Part Weight Part Weight
Under Collar Number lb Number lb Number lb Number lb
5" Asphalt Cutter
12" 22040935 6.75 50190404 7.25 50185982 8.5 50185990 9.25
Asphalt cutting and
5-1/2" Clay Hex Shank Size 7/8" x 3-1/4" 1" x 4-1/4" 1-1/8" x 6" 1-1/4" x 6"
Length Part Weight Part Weight Part Weight Part Weight
Spade Under Collar Number lb Number lb Number lb Number lb
5-1/2" Clay Spade
16" 50189596 7 50189554 7.25 50189562 8.5 50189570 11
Trench digging and
trimming
3" Digging Hex Shank Size 7/8" x 3-1/4" 1" x 4-1/4" 1-1/8" x 6" 1-1/4" x 6"
Chisel Length Part Weight Part Weight Part Weight Part Weight
Under Collar Number lb Number lb Number lb Number lb
3" Digging Chisel
16" 22040968 7.5
22040976 8 22040984 10 50186014 11.5
Digging and deeper
asphalt cutting
Frost Wedge Hex Shank Size 7/8" x 3-1/4" 1" x 4-1/4" 1-1/8" x 6" 1-1/4" x 6"
Length Part Weight Part Weight Part Weight Part Weight
Under Collar Number lb Number lb Number lb Number lb
Frost Wedge
Used for breaking
frozen ground 16-1/2" FW40810 7 FW40820 10 FW40830 13 FW40840 18
Bushing Tool Hex Shank Size 7/8" x 3-1/4" 1" x 4-1/4" 1-1/8" x 6" 1-1/4" x 6"
Length Part Weight Part Weight Part Weight Part Weight
Under Collar Number lb Number lb Number lb Number lb
BUSHING TOOL
Concrete surface 9" BT41310 5 BT41320 6.5 BT41330 7 BT41340 7.25
removal or roughing
ingersollrandproducts.com/accessories
76 Consumables & Attachments | Pneumatic Tool Steels & Accessories
Concrete Hex Shank Size 7/8" x 3-1/4" 1" x 4-1/4" 1-1/8" x 6" 1-1/4" x 6"
Length Part Weight Part Weight Part Weight Part Weight
Breaker Under Collar Number lb Number lb Number lb Number lb
Concrete Breaker
14-1/2" – – – – CB40960 11.25 CB40970 12.25
Breaking up concrete;
driven into drilled hole
1" Pipe Driver Hex Shank Size 7/8" x 3-1/4" 1" x 4-1/4" 1-1/8" x 6" 1-1/4" x 6"
Length Part Weight Part Weight Part Weight Part Weight
Under Collar Number lb Number lb Number lb Number lb
1" Pipe Driver
Driving steel pipe up
Pneumatic Tool Steels
1-1/2" Pipe Hex Shank Size 7/8" x 3-1/4" 1" x 4-1/4" 1-1/8" x 6" 1-1/4" x 6"
Driver Length Part Weight Part Weight Part Weight Part Weight
Under Collar Number lb Number lb Number lb Number lb
1-1/2" Pipe Driver
11" – – – – 22040547 7 22040554 7.5
Driving steel pipe up
to 1-1/2" O.D.
Ground Hex Shank Size 7/8" x 3-1/4" 1" x 4-1/4" 1-1/8" x 6" 1-1/4" x 6"
Rod Driver Length Part Weight Part Weight Part Weight Part Weight
Under Collar Number lb Number lb Number lb Number lb
Ground Rod Driver
9" – – 22040588 5.25 22040596 6.75 22040604 7.25
Driving steel rod up
to 1" O.D.
3-Piece Sign Hex Shank Size 7/8" x 3-1/4" 1" x 4-1/4" 1-1/8" x 6" 1-1/4" x 6"
Post Driver Length Part Weight Part Weight Part Weight Part Weight
Under Collar Number lb Number lb Number lb Number lb
3-Piece Sign Post Driver
7-3/4" 22040778 5 22040943 5.25 22041008 5.25 22041016 6
Includes shank, post
block, and 3-1/2" driver
77
Detachable Hex Shank Size 7/8" x 3-1/4" 1" x 4-1/4" 1-1/8" x 6" 1-1/4" x 6"
Shank Length Part Weight Part Weight Part Weight Part Weight
Under Collar Number lb Number lb Number lb Number lb
Detachable Shank
9" 22040927 4 50187830 4.5 50187848 5.25 50187855 6
Used with tent stake
drivers and tamping
pads
2" Tent Stake Hex Shank Size 7/8" x 3-1/4" 1" x 4-1/4" 1-1/8" x 6" 1-1/4" x 6"
Length Part Weight Part Weight Part Weight Part Weight
Driver Under Collar Number lb Number lb Number lb Number lb
2" Tent Stake Driver
2-1/2" Tent Hex Shank Size 7/8" x 3-1/4" 1" x 4-1/4" 1-1/8" x 6" 1-1/4" x 6"
Length Part Weight Part Weight Part Weight Part Weight
Stake Driver Under Collar Number lb Number lb Number lb Number lb
2-1/2" Tent Stake Driver
N/A 22040646 4 22040646 4 22040646 4 22040646 4
Used with detachable
shank
6" Tamping Pad Hex Shank Size 7/8" x 3-1/4" 1" x 4-1/4" 1-1/8" x 6" 1-1/4" x 6"
Square Length Part Weight Part Weight Part Weight Part Weight
Under Collar Number lb Number lb Number lb Number lb
6" Tamping Pad Square
N/A 51305894 10.5 51305894 10.5 51305894 10.5 51305894 10.5
Tamping and backfilling;
used with detachable
shank
Hex Shank Size 7/8" x 3-1/4" 1" x 4-1/4" 1-1/8" x 6" 1-1/4" x 6"
8" Tamping Pad
Length Part Weight Part Weight Part Weight Part Weight
Square Under Collar Number lb Number lb Number lb Number lb
8" Tamping Pad Square
N/A 50187897 14.5 50187897 14.5 50187897 14.5 50187897 14.5
Tamping and backfilling;
used with detachable
shank
ingersollrandproducts.com/accessories
78 Consumables & Attachments | Pneumatic Tool Steels & Accessories
Sets
Jackhammer Rods Hex Shank Size 7/8" x 3-1/4" 7/8" x 4-1/4" 1" x 4-1/4"
Length
Under Part Weight Part Weight Part Weight
Diameter Depth Collar Number lb Number lb Number lb
Hexagon shank whirlibits
carbide-tipped drill steels Hexagon Shank Whirlibits Carbide-Tipped Drill SteelS
5/8" 6" 9" WB5869 1.5 WBA5869 1.75 – –
5/8" 9" 12" WB58912 1.75 WBA58912 2 – –
5/8" 15" 18" WB581518 2 WBA581518 2.25 – –
5/8" 21" 24" WB582124 2.5 WBA582124 2.75 – –
5/8" 27" 30" WB582730 3 WBA582730 3.25 – –
3/4" 6" 9" WB3469 1.75 WBA3469 2 – –
3/4" 9" 12" WB34912 2 WBA34912 2.25 WBC34912 2.5
3/4" 15" 18" WB341518 2.5 WBA341518 2.75 WBC341518 3
3/4" 21" 24" WB342124 3 WBA342124 3.25 WBC342124 3.5
3/4" 27" 30" WB342730 3.5 WBA342730 3.75 WBC342730 4
3/4" 33" 36" WB343336 3.75 WBA343336 4 – –
3/4" 45" 48" WB344548 4.25 WBA344548 4.5 – –
7/8" 6" 9" WB7869 2 WBA7869 2.25 – –
7/8" 9" 12" WB78912 2.5 WBA78912 2.75 WBC78912 2.5
7/8" 15" 18" WB781518 3 WBA781518 3.25 WBC781518 3.25
7/8" 21" 24" WB782124 3.75 WBA782124 4 WBC782124 4
7/8" 27" 30" WB782730 4.5 WBA782730 4.75 WBC782730 4.5
7/8" 33" 36" WB783336 5 WBA783336 5.25 WBC783336 5.5
7/8" 45" 48" WB784548 6.25 WBA784548 6.5 – –
ingersollrandproducts.com/accessories
80 Consumables & Attachments | Pneumatic Tool Steels & Accessories
Jackhammer Rods Hex Shank Size 7/8" x 3-1/4" 7/8" x 4-1/4" 1" x 4-1/4"
Length
Under Part Weight Part Weight Part Weight
Diameter Depth Collar Number lb Number lb Number lb
Hexagon Shank Whirlibits
Carbide-tipped Drill Steel Hexagon Shank Whirlibits Carbide-Tipped Drill SteelS
1" 9" 12" WB1912 2.75 WBA1912 3 WBC1912 3
1" 15" 18" WB11518 3.5 WBA11518 3.75 WBC11518 4
1" 21" 24" WB12124 4.25 WBA12124 4.5 WBC12124 5
1" 27" 30" WB12730 5.25 WBA12730 5.5 WBC12730 5.75
1" 33" 36" WB13336 6 WBA13336 6.25 – –
1" 45" 48" WB14548 7.5 WBA14548 7.75 – –
1-1/8" 9" 12" WB118912 3 WBA118912 3.25 WBC118912 3.75
1-1/8" 15" 18" WB1181518 4 WBA1181518 4.25 WBC1181518 4.5
Pneumatic Tool Steels
Jackhammer Rods Hex Shank Size 7/8" x 3-1/4" 7/8" x 4-1/4" 1" x 4-1/4"
Length Part Weight Part Weight Part Weight
Under Collar Number lb Number lb Number lb
ingersollrandproducts.com/accessories
82 Consumables & Attachments | Pneumatic Tool Steels & Accessories
Sets
Our jumbo shank rivet buster steels and attachments are ideal
for general demolition and steel demolition applications.
Pneumatic Tool Steels
Jumbo shank
Backout Punches
Backout Punches Weight
Length Rivet Diameter Part Number lb
Backout Punches
Removing bolts and rivets 9-1/2" 3/8" 9001-278 2
9-1/2" 1/2" 9001-279 2
9-1/2" 5/8" 9001-280 2
9-1/2" 3/4" 9001-281 2.25
9-1/2" 7/8" 9001-282 2.25
9-1/2" 1" 9001-283 2.25
ingersollrandproducts.com/accessories
84 Consumables & Attachments | Pneumatic Tool Steels & Accessories
Sets
round shank oval collar hex shank oval collar round shank round collar hex shank round collar
Round Shank Oval Collar Hex Shank Oval Collar Round Shank Round Collar Hex Shank Round Collar
1" Flat Chisels Part Part Part Part Weight
Length Number Number Number Number lb
1" Flat Chisels
General demolition 9" HH1-215F-9 HH1-214F-9 H3R-215F-9 H3R-214F-9 1.25
12" HH1-215F-12 HH1-214F-12 H3R-215F-12 H3R-214F-12 1.75
18" HH1-215F-18 HH1-214F-18 H3R-215F-18 H3R-214F-18 2.5
24" HH1-215F-24 HH1-214F-24 H3R-215F-24 H3R-214F-24 3
36" HH1-215F-36 HH1-214F-36 H3R-215F-36 H3R-214F-36 5.25
48" HH1-215F-48 HH1-214F-48 H3R-215F-48 H3R-214F-48 6
60" HH1-215F-60 HH1-214F-60 H3R-215F-60 H3R-214F-60 9
72" HH1-215F-72 HH1-214F-72 H3R-215F-72 H3R-214F-72 9.25
84" HH1-215F-84 HH1-214F-84 H3R-215F-84 H3R-214F-84 13.25
96" HH1-215F-96 HH1-214F-96 H3R-215F-96 H3R-214F-96 15.25
85
Moil Points Round Shank Oval Collar Hex Shank Oval Collar Round Shank Round Collar Hex Shank Round Collar
Part Part Part Part Weight
Length Number Number Number Number lb
Moil Points
General demolition
9" HH1-215M-9 HH1-214M-9 H3R-215M-9 H3R-214M-9 1.25
12" HH1-215M-12 HH1-214M-12 H3R-215M-12 H3R-214M-12 1.75
18" HH1-215M-18 HH1-214M-18 H3R-215M-18 H3R-214M-18 2.5
24" HH1-215M-24 HH1-214M-24 H3R-215M-24 H3R-214M-24 3
36" HH1-215M-36 HH1-214M-36 H3R-215M-36 H3R-214M-36 5.25
1-1/2" Scaling Round Shank Oval Collar Hex Shank Oval Collar Round Shank Round Collar Hex Shank Round Collar
Part Part Part Part Weight
Chisels Length Number Number Number Number lb
1-1/2" Scaling Chisels
9" HH1-215B-9 HH1-214B-9 H3R-215B-9 H3R-214B-9 1.25
General demolition 12" HH1-215B-12 HH1-214B-12 H3R-215B-12 H3R-214B-12 1.75
18" HH1-215B-18 HH1-214B-18 H3R-215B-18 H3R-214B-18 2.5
2" Scaling Chisels Round Shank Oval Collar Hex Shank Oval Collar Round Shank Round Collar Hex Shank Round Collar
Part Part Part Part Weight
Length Number Number Number Number lb
2" Scaling Chisels
General demolition 9" HH1-323-9 HH1-324-9 H3R-423-9 H3R-424-9 1.25
12" HH1-323-12 HH1-324-12 H3R-423-12 H3R-424-12 2
18" HH1-323-18 HH1-324-18 H3R-423-18 H3R-424-18 2.5
24" HH1-323-24 HH1-324-24 H3R-423-24 H3R-424-24 3.5
36" HH1-323-36 HH1-324-36 H3R-423-36 H3R-424-36 5.25
48" HH1-323-48 HH1-324-48 H3R-423-48 H3R-424-48 7
60" HH1-323-60 HH1-324-60 H3R-423-60 H3R-424-60 9.25
72" HH1-323-72 HH1-324-72 H3R-423-72 H3R-424-72 11
84" HH1-323-84 HH1-324-84 H3R-423-84 H3R-424-84 12.5
96" HH1-323-96 HH1-324-96 H3R-423-96 H3R-424-96 14.5
3" Scaling
Round Shank Oval Collar Hex Shank Oval Collar Round Shank Round Collar Hex Shank Round Collar
Chisels Part Part Part Part Weight
Length Number Number Number Number lb
3" Scaling Chisel
Bushing Tools Round Shank Oval Collar Hex Shank Oval Collar Round Shank Round Collar Hex Shank Round Collar
Part Part Part Part Weight
Length Number Number Number Number lb
BUSHING TOOL
Concrete surface
9" HH1-215T-9 HH1-214T-9 H3R-215T-9 H3R-214T-9 2.5
removal or roughing
ingersollrandproducts.com/accessories
86 Consumables & Attachments | Pneumatic Tool Steels & Accessories
Tooth Round Shank Oval Collar Hex Shank Oval Collar Round Shank Round Collar Hex Shank Round Collar
Part Part Part Part Weight
Length Number Number Number Number lb
Ripper Round Shank Oval Collar Hex Shank Oval Collar Round Shank Round Collar Hex Shank Round Collar
Part Part Part Part Weight
Length Number Number Number Number lb
Splitting steel ripper
12" HH1-215R-12 HH1-214R-12 H3R-215R-12 H3R-214R-12 1.75
Round Nose Round Shank Oval Collar Hex Shank Oval Collar Round Shank Round Collar Hex Shank Round Collar
Pneumatic Tool Steels
Straight Fuller Round Shank Oval Collar Hex Shank Oval Collar Round Shank Round Collar Hex Shank Round Collar
Part Part Part Part Weight
Length Number Number Number Number lb
Gouge Round Shank Oval Collar Hex Shank Oval Collar Round Shank Round Collar Hex Shank Round Collar
Part Part Part Part Weight
Length Number Number Number Number lb
Caulking Round Shank Oval Collar Hex Shank Oval Collar Round Shank Round Collar Hex Shank Round Collar
Part Part Part Part Weight
Length Number Number Number Number lb
Diamond Point Round Shank Oval Collar Hex Shank Oval Collar Round Shank Round Collar Hex Shank Round Collar
Part Part Part Part Weight
Length Number Number Number Number lb
Cape Chisel Round Shank Oval Collar Hex Shank Oval Collar Round Shank Round Collar Hex Shank Round Collar
Part Part Part Part Weight
Length Number Number Number Number lb
ingersollrandproducts.com/accessories
88 Consumables & Attachments | Pneumatic Tool Steels & Accessories
Part Number
Rubber Buffered (threaded) Barrel Area Type K, A, D Series W Series
Rubber Buffered (standard on all W Series chippers)
Threaded – HHW1-A300
Sets
1/2" Offset Flat Chisel Hex Shank Size 7" 9" 12" 18"
Part Weight Part Weight Part Weight Part Weight
Number lb Number lb Number lb Number lb
1/2" Offset Flat Chisel
401OFC127 0.5 401OFC129 0.75 401OFC1212 1 401OFC1218 1.25
1/2" Sidecut Chisel Hex Shank Size 7" 9" 12" 18"
Part Weight Part Weight Part Weight Part Weight
Number lb Number lb Number lb Number lb
1/2" Sidecut Chisel
401SC127 0.75 401SC129 0.75 401SC1212 1 401SC1218 1.25
Offset Sidecut Chisel Hex Shank Size 7" 9" 12" 18"
Part Weight Part Weight Part Weight Part Weight
Number lb Number lb Number lb Number lb
offset Sidecut Chisel
401OSC127 0.75 – – – – – –
1-1/4" Wide Flat Blade Hex Shank Size 7" 9" 12" 18"
Part Weight Part Weight Part Weight Part Weight
Number lb Number lb Number lb Number lb
1-1/4" wide flat blade
401WBC1147 0.5 401WBC1149 0.75 401WBC11412 1 401WBC11418 1.25
ingersollrandproducts.com/accessories
90 Consumables & Attachments | Pneumatic Tool Steels & Accessories
3/4" Flat Chisel Hex Shank Size 7" 9" 12" 18"
Part Weight Part Weight Part Weight Part Weight
Number lb Number lb Number lb Number lb
3/4" Flat Chisel
401FC347 0.5 401FC349 0.75 401FC3412 1 401FC3418 1.5
Pneumatic Tool Steels
Chisel Set 5-piece high-quality chisel set made 4-piece high-quality chisel set made
of heat-treated alloy of heat-treated alloy
9500/9501
• Tapered punch • Tapered punch
• Flat chisel • Panel cutter
• Panel cutter • Flat chisel
• Sheet metal cutter • Spot weld breaker
• Spot weld breaker
Accessories
Quick Change Retainer Manufacturer Fits Models
9512 Ingersoll Rand 115, 116, 117, 121, 132
Chicago Pneumatic All 0.401 shank hammers except CP7 16
Cleco E3, E4, E15, E16
Dayton All
Sets
ingersollrandproducts.com/accessories
92 Consumables & Attachments | Pneumatic Tool Steels & Accessories
Sets
INgersoll rand
Scaler Chisels
Blank Hex Shank Size 7" 12" 18"
Part Weight Part Weight Part Weight
Number lb Number lb Number lb
Blank
WF-14-007 0.5 WF-14-12 0.75 WF-14-18 1.25
ingersollrandproducts.com/accessories
94 Consumables & Attachments | Pneumatic Tool Steels & Accessories
CLECO
Chicago Pneumatic
Narrow
ingersollrandproducts.com/accessories
96 Consumables & Attachments | Pneumatic Tool Steels & Accessories
Bulk Needles
Part Number Description Quantity
Bulk Needles
22038194 2 mm needle holder for 170PG N/A
22038202 2 mm needle holder for 180PG N/A
22038210 4 mm needle holder for 180PG N/A
22038525 2 mm flat tip 7" steel 100
22038533 3 mm flat tip 5" steel 100
22038566 3 mm flat tip 7" beryllium 500
22038558 3 mm flat tip 7" beryllium 100
22038541 3 mm flat tip 7" steel 1,000
89940597 3 mm flat tip 7" steel 100
22038582 3 mm chisel tip 7" steel 1,000
22038574 3 mm chisel tip 7" steel 100
22038608 3 mm pointed tip 7" steel 1,000
22038590 3 mm pointed tip 7" steel 100
22038624 4 mm flat tip 7" steel 500
22038616 4 mm flat tip 7" steel 100
22038640 4 mm chisel tip 7" steel 500
22038632 4 mm chisel tip 7" steel 100
22038665 4 mm pointed tip 7" steel 500
22038657 4 mm pointed tip 7" steel 100
97
ingersollrandproducts.com/accessories
98 Consumables & Attachments | Abrasives & Pads
Ingersoll Rand offers a complete line of 1-1/2" to 3" surface-conditioning discs designed
to maximize the productivity of our grinders, while ensuring the best possible finishes.
AO Series Quick-Change
Quick-Change Backer Pads Sanding Discs
Part Number Description Part Number Description Grit
Abrasives & Pads
03A-FRMPD 3" Firm holder pad w/ 1/4" mandrel 02A-080AO-100 2" AO Series sanding disc 80
02A-120AO-100 2" AO Series sanding disc 120
02A-180AO-100 2" AO Series sanding disc 180
02A-240AO-100 2" AO Series sanding disc 240
03A-036AO-50 3" AO Series sanding disc 36
03A-050AO-50 3" AO Series sanding disc 50
03A-080AO-50 3" AO Series sanding disc 80
03A-120AO-50 3" AO Series sanding disc 120
03A-180AO-50 3" AO Series sanding disc 180
03A-240AO-50 3" AO Series sanding disc 240
Automotive Packs (smaller quantity flip-top BOxes)
AO Series 02A-036AO-25 2" AO series sanding disc 36
Features Benefits 02A-050AO-25 2" AO series sanding disc 50
Quick-change Instant disc changes; disc is 02A-080AO-25 2" AO Series sanding disc 80
fastening systems centered; smooth-running 02A-120AO-25 2" AO Series sanding disc 120
Multiple layers of backing Works well on flat and 02A-180AO-25 2" AO Series sanding disc 180
contoured surfaces
02A-240AO-25 2" AO Series sanding disc 240
Aggressive stock removal Greater productivity
03A-036AO-25 3" AO Series sanding disc 36
03A-050AO-25 3" AO Series sanding disc 50
03A-080AO-25 3" AO Series sanding disc 80
03A-120AO-25 3" AO Series sanding disc 120
03A-180AO-25 3" AO Series sanding disc 180
03A-240AO-25 3" AO Series sanding disc 240
99
ingersollrandproducts.com/accessories
100 Consumables & Attachments | Abrasives & Pads
Available in coarse,
medium, and fine grit.
101
02A-080AO-6 2" AO Series sanding disc 80 03F-SFTWL-6 3" Hook & loop wool pad (for compounding)
02A-120AO-6 2" AO Series sanding disc 120 03F-MEDFM-6 3" Hook & loop waffle pad white (for compounding)
03A-036AO-6 3" AO Series sanding disc 36 03F-SFTFM-6 3" Hook & loop waffle pad yellow (for polishing)
ingersollrandproducts.com/accessories
102 Consumables & Attachments | Abrasives & Pads
Whatever your surface preparation needs happen to be, we offer a full range of sanding,
backing, and polishing pads. Genuine Ingersoll Rand pads are specifically engineered to work
at the tolerances of our powerful tools, ensuring you get the best finishes possible.
ingersollrandproducts.com/accessories
104 Consumables & Attachments | Abrasives & Pads
Cutting Discs
Sets
These high quality Type 1 discs are designed for cutting through metal materials.
Common applications include cutting exhaust pipes, trimming bolts, and slicing
through sheet metal. The fiber reinforcement and the 1/16'' thickness produces a
disc that cuts quickly but remains durable. For use with any 3/8'' arbor cutting tool.
Maximum 25,000 RPM speed rating.
Cutting Discs
Abrasives & Pads
ingersollrandproducts.com/accessories
106 Consumables & Attachments | Burs, Stones, & Collets
Ingersoll Rand carbide burs set the industry standard for quality and are the perfect
complements to our innovative grinders and finishing tools. You’ll find a complete
range of versatile, durable, high-precision burs, in a variety of types and sizes.
Multi-shaped
**Solid carbide bur with steel shank.
ingersollrandproducts.com/accessories
108 Consumables & Attachments | Burs, Stones, & Collets
Bur Head
Style Shank Diameter
1818TiN Kits
Cylindrical 1/8" 1/8" 814TiN
Boxed Kit
Ball-nosed cylindrical 1/8" 1/8"
Ball-nosed tree 1/8" 1/8"
Ball-nosed Cone 1/8" 1/8"
Pointed tree 1/8" 1/8"
Ball 1/8" 1/8"
814TiN Boxed kits
Cylindrical 1/4" 1/2 & 3/8"
Ball-nosed cylindrical 1/4" 1/2 & 3/8"
Burs, Stones & Collets
This 8-piece carbide bur kit contains the most popular sizes in a durable storage box.
This 30-piece carbide bur mega set covers a wide range of applications. The kit includes
each available bur with 1/8" and 1/4" shank with various head diameters. M30TiN
Boxed Kit
NOTE: Burs have a maximum operating speed of 40,000 rpm.
Collets
Part
Number Size Where Used
Tapper Collets
2U-103-1/4 1/4" Tappers
4U-103-1/2 1/2" Tappers
DIE Grinder collets
DG110-700-6MM 6 mm Metric die grinder
DG110-700-G2 1/8" Die grinder
301-700C 1/8" 3102 and 3108 Series
DG110-700-G4 1/4" Die grinder
DG110-700-G2
G160HD-700-1/4 1/4" Die and horizontal grinders
307-700 1/4" 3102 and 3108 series
DG120-700-G6 3/8" Die grinder
DG120-700-G6
Part
Number Size Description Where Used
Horizontal grinder collet body assemblY
DG220-A290-G4 1/4" Replacement collet All grinder models ending in G4,
body assembly except C Series and G1 Series;
Pro Series (61H) DG220-A290-G6
109
ingersollrandproducts.com/accessories
110 Consumables & Attachments | Air Reciprocating Saw Blades
Sets
Part Number Description TPI
P4FS-6 6-Pack — Fine standard pitch air recip saw blade 32
P4CS-6 6-Pack — Coarse standard pitch air recip saw blade 34
P4EV-6 6-Pack — Extra coarse variable pitch air recip saw blade 14/18
P4FS-20 20-Pack — Fine standard pitch air recip saw blade 32
P4CS-20 20-Pack — Coarse standard pitch air recip saw blade 24
P4EV-20 20-Pack — Extra coarse variable pitch air recip saw blade 14/18
P4FS-50 50-Pack — Fine standard pitch air recip saw blade 32
P4CS-50 50-Pack — Coarse standard pitch air recip saw blade 24
P4EV-50 50-Pack — Extra coarse variable pitch air recip saw blade 14/18
Ingersoll Rand blades can be used with all standard 1/2” shank air reciprocating saws.
111
ingersollrandproducts.com/accessories
112 Consumables & Attachments | Drill & Nutrunner Bits
Bits
Sets
Our quick change driver bits and related accessories are the
perfect complement to our line of fastening tools. All sets
come in ballistic nylon accessory cases.
Drill & Nutrunner Bits
ingersollrandproducts.com/accessories
114 Consumables & Attachments | Drill & Nutrunner Bits
ingersollrandproducts.com/accessories
116 Consumables & Attachments | Drill & Nutrunner Bits
No matter what you're drilling needs may be, count on Ingersoll Rand
for the bits you require to get the job done. We offer a variety of drill
bit sets of different material compositions to allow you the flexibility
to match the bit to your specific job.
ingersollrandproducts.com/accessories
118 Consumables & Attachments | Drill & Nutrunner Bits
Drill Adapters
Part Thread Morse Taper Drive
Number Size Number Size
Square Drive Adapter
R0H-P212-3/8 3/8" x 24 – 3/8"
Socket Adapters
R4J-214 3 3/4" – 3 3/4"
R5SM-214 – 5 1"
Quick Change Adapter
R0H-A925-4 3/8" x 24 – 1/4"
Standard-duty Chucks
7801-99-6 0 – 3/8" Standard-duty 3/8" x 24 728N-253
7806-99-8 0 – 1/2" Standard-duty 3/8" x 24 728N-253
MEDIUM-duty Chucks R0H-99
R0H-99 0 – 1/4" Medium-duty 3/8" x 24 R1H-J253
HEAVY-duty Chucks
6A-99 0 – 3/8" Heavy-duty 3/8" x 24 R0J-J253
R00A-99 0 – 1/4" Heavy-duty 3/8" x 24 R00A-J253
R0K-99 5/64" – 1/2" Heavy-duty 3/8" x 24 R1T-J253 6A-99
ingersollrandproducts.com/accessories
120 Consumables & Attachments | Drill & Nutrunner Bits
DE-215A
DE-323A-2
R33SW-151-1/2 K-27
TC-365
121
ingersollrandproducts.com/accessories
122 Consumables & Attachments | Drill & Nutrunner Bits
"A"
T Diameter "L" Screw Size
Part Number Size in (mm) Length Range Quantity
Slot Bits
DLB2220-10 0.012 .078" (1.981) 1.7" 00 – 0 10
DLB2221-10 0.012 .097" (2.464) 1.7" 00 – 0 10
DLB2222-10 0.016 .116" (2.946) 1.7" 0–2 10
DLB2223-10 0.02 .157" (3.988) 1.7" 2–4 10
DLB2224-10 0.026 .196" (4.987) 1.7" 3–5 10
"H"
Srew Hex Size "L" Use
Part Number Size in (mm) Length Diagram Quantity
Hexagon, Male and Female
DLB2321-10 0.12 .06" (1.5) 1.7" Male 10
DLB2322-10 0.16 .08" (2) 1.7" Male 10 Male
DLB2323-10 0.24 .12" (3) 1.7" Male 10
DLB2324-10 0.31 .16" (4) 1.7" Male 10
DLB2420-10 – 09" (2.3) 1.7" Female 10
DLB2421-10 – .10" (2.5) 1.7" Female 10
DLB2422-10 – .12" (3) 1.7" Female 10 Female
DLB2423-10 0.08 .16" (4) 1.7" Female 10
DLB2424-10 0.09 .18" (4.5) 1.7" Female 10
DLB2425-10 0.1 .20" (5) 1.7" Female 10
DLB2426-10 0.12 .22" (5.5) 1.7" Female 10
123
1/4" Hex
Part Number Description For Use With
Insert Bit Holders
M631-4 Magnetic All screwdriver models M631-4
RX2-631-4 Non-magnetic All screwdriver models
DLW-4100 Slotted bit holder EL0109B
DLW-4100
ingersollrandproducts.com/accessories
124
Spring Balancers
125
Spring Balancers
Sets
Spring Balancers
• Stainless-steel cable; nylon cable option Features
available for the 2.2 lb (1 kg) capacity model; • Rugged construction, cast aluminum body
order BLD1/P for this option • Stainless-steel cable
• Adjustable capacity • Adjustable capacity
• Adjustable stroke limiting device • Safety device against load dropping due to the spring
• Cable guide in anti-friction material breakage (>3 kg); not available on model BMDS-2
• Upper suspension shackle included on • Adjustable stroke limiting device
balancer for ease of installation • Cable guide in anti-friction material
• Upper suspension shackle included on
balancer for ease of installation
Model lb (kg) ft (m) lb (kg) Model lb (kg) ft (m) lb (kg)
BLD Series BMD Series
BLD1 1.3 (0.6) 5.2' (1600) 0.9 – 2.2 (0.4 – 1) BMDS-2 4.4 (2) 6.5' (2000) 2.2 – 5.5 (1 – 2.5)
BLD2 1.3 (0.6) 5.2' (1600) 2.2 – 4.4 (1 – 2) BMDS-4 4.4 (2) 6.5' (2000) 4.4 – 8.8 (2 – 4)
BLD3 1.3 (0.7) 5.2' (1600) 4.4 – 6.6 (2 – 3) BMDS-6 5.1 (2.3) 6.5' (2000) 8.8 – 13.2 (4 – 6)
BMDS-8 5.5 (2.5) 6.5' (2000) 13.2 – 17.6 (6 – 8)
ingersollrandproducts.com
126 Ergonomic Accessories | Spring Balancers
Model lb (kg) ft (m) lb (kg) Model lb (kg) ft (m) lb (kg)
BMDL Series BMDLL Series
BMDLN-4 6.4 (2.9) 8.2' (2500) 4.4 – 8.8 (2 – 4) BMDLLN-4 6.6 (3) 8.2' (2500) 4.4 – 8.8 (2 – 4)
BMDLN-6 7.1 (3.2) 8.2' (2500) 8.8 – 13.2 (4 – 6) BMDLLN-6 7.3 (3.3) 8.2' (2500) 8.8 – 13.2 (4 – 6)
BMDLN-8 7.7 (3.5) 8.2' (2500) 13.2 – 17.6 (6 – 8) BMDLLN-8 7.9 (3.6) 8.2' (2500) 13.2 – 17.6 (6 – 8)
BMDLN-10 8.2 (3.7) 8.2' (2500) 17.6 – 22 (8 –10) BMDLLN-10 8.4 (3.8) 8.2' (2500) 17.6 – 22.0 (8 – 10)
BMDLN-12 8.8 (4) 8.2' (2500) 22 – 30 (10 – 13.6)
Model lb (kg) ft (m) lb (kg) Model lb (kg) ft (m) lb (kg)
BID Series BHD Series
BIDS-7 5 (2.3) 6.5' (2000) 8.8 – 15.4 (4 – 7) BHD-15 22.7 (10.3) 6.5' (2000) 22 – 33 (10 – 15)
BIDS-10 5.5 (2.5) 6.5' (2000) 15.4 – 22 (7 – 10) BHD-20 23.4 (10.6) 6.5' (2000) 33 – 44 (15 – 20)
BIDS-14 5.5 (2.5) 6.5' (2000) 22 – 30.8 (10 –14) BHD-25 24.7 (11.2) 6.5' (2000) 44 – 55 (20 – 25)
BIDS-18 6.5 (2.9) 6.5' (2000) 30.8 – 39.6 (14 – 18) BHD-30 25.4 (11.5) 6.5' (2000) 55 – 66 (25 – 30)
BIDS-22 6.5 (2.9) 6.5' (2000) 39.6 – 48.4 (18 – 22) BHD-35 26 (11.8) 6.5' (2000) 66 – 77 (30 – 35)
BIDS-26 6.5 (2.9) 6.5' (2000) 48.4 – 55 (22 – 25) BHD-45 27.3 (12.4) 6.5' (2000) 77 – 99 (35 – 45)
BHD-55 27.6 (12.5) 6.5' (2000) 99 – 121 (45 – 55)
BHD-65 30 (13.6) 6.5' (2000) 121 – 143 (55 – 65)
SWL = Safe Working Load
127
Dimension Dimension
Type Type
Model lb (kg) ft (m) lb (kg) Model lb (kg) ft (m) lb (kg)
BSD Series BSDL Series
BSD-20 41.9 (18.6) 8.2' (2500) 33 – 44 (15 – 20) A BSD-20 42.1 (19.1) 9.8' (3000) 33 – 44 (15 – 20) A
BSD-30 43.7 (19.8) 8.2' (2500) 44 – 66 (20 – 30) A BSD-25 43.9 (19.9) 9.8' (3000) 44 – 55 (20 – 25) A
BSD-40 45.9 (20.8) 8.2' (2500) 66 – 88 (30 – 40) A BSD-35 46.1 (20.9) 9.8' (3000) 55 – 77 (25 – 35) A
BSD-50 52.7 (23.9) 8.2' (2500) 88 – 110 (40 – 50) A BSD-45 52.5 (23.8) 9.8' (3000) 77 – 99 (35 – 45) B
BSD-60 56 (25.4) 8.2' (2500) 110 – 132 (50 – 60) A BSD-50 52.7 (23.9) 9.8' (3000) 99 – 110 (40 – 50) B
BSD-70 59.1 (26.8) 8.2' (2500) 132 – 154 (60 – 70) B BSD-60 55.8 (25.3) 9.8' (3000) 110 – 132 (50 – 60) B
BSD-80 61.3 (27.8) 8.2' (2500) 154 – 176 (70 – 80) B BSD-70 58.9 (26.7) 9.8' (3000) 132 – 154 (60 – 70) B
BSD-90 63.5 (28.8) 8.2' (2500) 176 – 198 (80 – 90) B BSD-80 61.7 (28) 9.8' (3000) 154 – 176 (70 – 80) B
BSD-100 78.5 (35.6) 8.2' (2500) 198 – 220 (90 – 100) C BSD-90 64 (29) 9.8' (3000) 176 – 198 (80 – 90) B
Spring Balancers
BSD-120 85.3 (38.8) 8.2' (2500) 220 – 265 (100 – 120) C BSD-100 81.1 (36.8) 9.8' (3000) 198 – 220 (90 – 100) C
BSD-140 92.2 (41.8) 8.2' (2500) 265 – 309 (120 – 140) C BSD-115 85.3 (38.7) 9.8' (3000) 220 – 254 (100 –115) C
BSD-150 98.1 (44.5) 8.2' (2500) 287 – 330 (130 – 150) C BSD-130 88 (39.9) 9.8' (3000) 254 – 286 (115 – 130) C
BSD-165 106.3 (48.2) 8.2' (2500) 330 – 363 (150 – 165) C BSD-140 94.4 (42.8) 9.8' (3000) 286 – 309 (130 – 140) C
BSD-150 100.6 (45.6) 9.8' (3000) 309 – 330 (140 – 150) C
ingersollrandproducts.com
128 Ergonomic Accessories | Spring Balancers
Dimensional Info
.3”
1/4”
11.75”
10.2”
.2 11.5”
4”
1/4”
.3”
.3”
13”
10.8”
.4 13.6”
.3 11.1” ”
”
24”
24.4”
22.8” 22.1”
.5” .7”
BSD Series
A B C
8.7” 12” 9.1” 12” 14.8”
12”
1” 1” 1”
1.1” 1.1”
1.1” 3.4”
.6” .6”
.6”
26”
24” 26”
27.6”
27.6” 27.6”
.7” .7”
.7”
129
ingersollrandproducts.com
130 Ergonomic Accessories | Torque Reaction Arms
Ingersoll Rand QTA bench-mounted torque reaction arms are constructed of lightweight aluminum
and are available in a variety of torque capacities, ranging from 10 to 150 Nm. They include an
Ingersoll Rand spring-loaded, die-cast aluminum balancer for impressive strength and reduced weight.
Spring balancer adjusts easily and Cable or air line clamps keep
offers effortless vertical movement. work area clear and organized.
Max.
Working
Reach
Model ft-lb (Nm) lb (kg) in (mm) in (mm) in (mm)
QTA010 7.4 (10) 2.64 (1.20) 15" (381) 13.0" (330) 27.8" (706)
QTA020 14.8 (20) 5.00 (2.27) 20" (508) 14.5" (368) 31.8" (808)
QTA040 29.5 (40) 6.50 (2.95) 25" (635) 17.5" (445) 39.7" (1008)
QTA100 73.8 (100) 8.00 (3.63) 30" (762) 17.5" (445) 39.7" (1008)
QTA150 110.6 (150) 10.00 (4.54) 52" (1321) 22.0" (559) 78.7" (2000)
NOTE: QTA150 is adjustable to mount to the floor or a bench and does not include a tool holder.
SWL = Safe Working Load.
Torque Arms
Accessories QTA010 QTA020 QTA040 QTA100
Inverse mounting kit IMK010 IMK020 IMK100 IMK100 Inverse mounting kit Upper pole clamp
Upper pole clamp PUC010 PUC020 PUC100 PUC100
131
Ingersoll Rand
air regulator
included with
QTA270 and
QTA475 arms.
Max.
Working
Reach
Model ft-lb (Nm) lb (kg) in (mm) in (mm) in (mm)
QTA270 model
QTA150 110.6 (150) 10.0 (4.5) 52" (1321) 22.0" (559) 78.7" (2000) shown
QTA270 199 (270) 22.0 (10.0) 60" (1524) 18.8" (477) 78.7" (2000)
QTA475 350 (475) 50.6 (23.0) 79" (2007) 23.2" (590) 78.7" (2000)
Note: Arms above do not include tool holders (please refer to the following page for holders for your Ingersoll Rand tools).
SWL = Safe Working Load
ingersollrandproducts.com
132 Ergonomic Accessories | Torque Reaction Arms
Torque Arms Generic tool holders are not available
Tool Holders QTA010 QTA020 QTA040 QTA100 for arms 150 Nm and above.
Flange mounting is recommended for in-line
Inline (included with arm) ITC010-1C ITC040-1C ITC040-1C ITC100-1C tools with torque capacity above 40 Nm.
Right angle ATC010-1C ATC040-1C ATC040-1C ATC100-1C Note the tool diameter range for
Pistol PTC010-1C PTC040-1C PTC040-1C – generic holders:
Rotating RTC010-1C RTC040-1C RTC040-1C – QTA010: 25 – 40 mm (1" – 1.57")
QTA020 / QTA040 / QTA100:
1/4" NPT NTC010-1T – – –
28 – 52 mm (1.1" – 2")
Note: Every Ingersoll Rand QE- or QA-specific tool holder listed in the table above accepts both angle and inline tools but requires an integrated flanged gear case or bolt-on mounting
flange to attach the tool holder to the tool. If your tool came with mounting style “P,” “R,” or “J,” order Part No. 15E4-K48 for any Ingersoll Rand-specific tool holder that ends with
“1B.” Order Part No. GEM120-K48 for any Ingersoll Rand-specific tool holder that ends with “2B.” Order Part No. QA4-K48 for any Ingersoll Rand-specific tool holder that ends with
“6B.”
Model Description
IRBS3-EO Basic station (no absorber)
IRBS3-N30 Air tool station with torque absorber
IRBS3-E30 Electric tool station with torque absorber
Note: Workstations do not include tool, spring balancer, air hose, or FRL. All must be purchased separately.
133
ingersollrandproducts.com
134 Ergonomic Accessories | Grips & Braces
Grips and braces are designed to provide comfort and better control while using
the tool. They help minimize reaction forces and vibrations to prevent harmful
effects to extremities.
Ergo-Grips ™
• Ergo-Grip™ makes tool operation more comfortable with reduced grip pressure and vibration dampening
• Easy installation:
1. Unscrew clutch housing.
2. Slip on grip.
3. Reattach housing.
Bio-Braces ™
• Ergonomically designed Bio Brace™ minimizes start-up and shut-off force to your arm.
• Eliminates the need for a dead handle, freeing up your other hand.
135
ingersollproducts.com/accessories
136 Maintenance | Lubricants & Grease Guns
It goes without saying that proper lubrication of any tool is essential if you
want the tool to last. By lubricating your air tools, you’ll prolong the life of
tool motors, mechanisms, gearing, and other vital parts. Ingersoll Rand offers
a complete line of specialized oils and greases that are engineered specifically
for use with our air tools. Also, grease guns are available for your convenience
to dispense the line of lubricants.
10P Class 1 #10 oils for use with percussive, assembly, and impact wrenches 1 pt
10G Class 1 #10 oils for use with percussive, assembly, and impact wrenches 1 gal
10G55 Class 1 #10 oils for use with percussive, assembly, and impact wrenches 55 gal
10GW Class 1 #10 oil and antifreeze for use with percussive, assembly, and impact wrenches 1 gal
50P Class II lubricant, #50 oil for use with grinders, impact wrenches, hoists, and winches 1 pt
50G Class II lubricant, #50 oil for use with grinders, impact wrenches, hoists, and winches 1 gal
62 1 Gal Class II #62 oil for hoist and winch gear boxes 1 gal
137
Greases
Part Number Description Grease No. Size
GREASES
23-1 LB For the gearing of drills 23 1 lb
28 1 LB For screwdriver gearing and clutches; drills, grinders, saws; tie tamper grease 28 1 lb
66 1 LB For slow-speed, high-torque angle heads 66 1 lb
66 8 LB For slow-speed, high-torque angle heads 66 8 lb
67-4T For high-speed, high-temp angle heads (green) 67 4 oz
67-1 LB For high-speed, high-temp angle heads (green) 67 1 lb
67 8 LB For high-speed, high-temp angle heads (green) 67 8 lb
68-1LB Coupling splines and high speed angle heads 68 1 lb
68 8 LB Coupling splines and high speed angle heads 68 8 lb
70 1 LB For large-piston motors and gear cases 70 1 lb
70 8 LB For large-piston motors and gear cases 70 8 lb
77-1 LB For grinder angle heads 77 1 lb
80 1 LB For bearings on sump pumps 80 1 lb
80 8 LB For bearings on sump pumps 80 8 lb
90-14 0Z For gear heads and tube nut wrenches 90 14 oz
100 1 LB Standard-duty impact wrench grease 100 1 lb
100 8 LB Standard-duty impact wrench grease 100 8 lb
105-4T Metallic housing impact wrench grease 105 4 oz
105-1LB Metallic housing impact wrench grease 105 1 lb
105-8LB Metallic housing impact wrench grease 105 8 lb
115-4T Composite housing impact wrench grease 115 4 oz
115-1LB Composite housing impact wrench grease 115 1 lb
150-1 LB For impact mechanisms with swinging weight 150 1 lb
150 8 LB For impact mechanisms with swinging weight 150 8 lb
170-1LB Premium impact grease for high temps, used with impact mechanisms 170 1 lb
105-4T 100 1 lb
ingersollproducts.com/accessories
138 Maintenance | Lubricants & Grease Guns
Lubrication Kits
Part Number Description
LUBRICATION KITS
The 10Z4, 10P, 10G, 100-1LB, 105-LBK1, & 115-LBK1 are available in case quantities.
See the website for quantities and part numbers.
105-LBK1
Grease Guns
Grease Guns Part Number Description
GREASE GUNS
P25-228 Push-type hand grease gun for hydraulic-type fittings, holds up to 3 oz of grease
P25-228
R000A2-228 Push-type hand grease gun for flush-type fittings, holds up to 3 oz of grease
GTH-1
Lubricants & Grease Guns
139
Hose inner
Ø NPT size Ø diameter
Ø Max. torque
Coiled hose
width
Coiled hose
Weight Ø
working length
Ø
Lift Length
Capacity
Approximate
travel
Overall height
ingersollproducts.com/accessories
Ingersoll Rand (NYSE:IR) advances the quality of life by creating and sustaining comfortable and efficient
environments. Our people and our family of brands—including Club Car®, Ingersoll Rand®, Thermo King®
and Trane® —work together to enhance the quality and comfort of air in homes and buildings; transport and protect
food and perishables; and increase industrial productivity and efficiency. Ingersoll Rand products range from complete
compressed air systems, tools and pumps to material handling systems. The diverse and innovative products, services
and solutions enhance our customers’ energy efficiency, productivity and operations. We are a $14 billion global
business committed to a world of sustainable progress and enduring results.
For more information, visit ingersollrandproducts.com.
ingersollrandproducts.com
Distributed by:
Ingersoll Rand, IR and the IR logo are trademarks of Ingersoll Rand, its subsidiaries and/or affiliates. All other trademarks are the property of their respective owners.
Nothing contained on these pages is intended to extend any warranty or representation, expressed or implied, regarding the product described herein.
Any such warranties or other terms and conditions of sale of products shall be in accordance with Ingersoll Rand’s standard terms and conditions of sale
for such products, which are available upon request.
Product improvement is a continuing goal at Ingersoll Rand. Designs and specifications are subject to change without notice or obligation.
We are committed to using environmentally conscious print practices. ©2014 Ingersoll Rand IRITS-0810-069 0413