Professional Documents
Culture Documents
Product Guide
Features
• 60 t (65 USt) capacity
MEGAFORM™ boom
The superstructure features a full-power four-section
MEGAFORM™ boom that can reach to a maximum
tip height of 119 ft. The sequence synchronized
extension features telescopic boom sections via a
single lever joystick controller.
Extensions
An optional bi-fold swingaway lattice extension
easily stows on the side of the base boom for easy Smooth
transport while providing on-board extension operation
from 33 ft - 56 ft for a maximum tip height of The RT765E-2 has
174.5 ft. By adding inserts of 20 ft or 40 ft, the a quick-reeve boom
maximum tip height on the RT765E-2 can be nose and swingaway
extended even further to 194 ft or 214 ft. alignment device to
help operators set up
An optional 33 ft fixed swingaway is also smoothly.
available with a maximum tip height of 150 ft.
Contents
Specifications 4
Working range 8
Load charts 9
Symbols glossary 10
Specifications
Superstructure
Cab
Superstructure continued
Fuel tank capacity
Rope diameter: 19 mm (3/4 in)
280 L (74 gal)
Rope length: 152 m (500 ft)
*Optional 152 m (500 ft) 35 x 7 class rope Transmission
Spicer powershift with 6 forward and 6 reverse speeds
Rope type: 6 x 37 class EIPS IWRC (3 speeds high and 3 speeds low). Front axle disconnect
*Optional 35 x 7 class rotation resistant for 4 x 2 travel.
Steering
Outrigger system
Fully independent power steering:
Four hydraulic telescoping single-stage double box Front: Full hydraulic, steering wheel controlled.
beam outriggers with inverted jacks and integral
holding valves. Three position settings, 100%, 50% Rear: Full hydraulic, switch controlled.
and fully retracted. All steel fabricated, quick-release Provides infinite variations of 4 main steering modes:
type round outrigger floats, 610 mm (24 in) diameter. front only, rear only, crab and coordinated.
Maximum outrigger pad load: 41 731 kg (92,000 lb). Rear steer centered indicating light.
Outrigger position monitoring system.
4 wheel outside turning radius - 6,7 m (22.1 ft).
Outrigger controls
Axles
Controls and crane level indicator located in cab.
Front: Drive/steer with differential and planetary
Engine (Tier III) reduction hubs rigid-mounted to frame.
Rear: Drive/steer with differential and planetary
Cummins QSB 6.7 L diesel, six cylinders, reduction hubs pivot-mounted to frame.
turbocharged, 179 kW (240 bhp) (Gross) at 2500
Automatic full hydraulic lockouts on rear axle permit
rpm. Maximum torque: 987 N-m (728 ft lb) at 1500
203 mm (8 in) oscillation only with boom centered
rpm.
over the front.
Note: Required for sale outside of North American and
European Union countries
Brakes
Engine (Tier IV)
Full hydraulic split circuit brakes operating on
Cummins QSB 6.7 L diesel, six cylinders, turbocharged
all wheels. Spring-applied, hydraulically released
with Cummins Diesel Particulate Exhaust filter/
axle-mounted parking brake.
muffler. Meets emissions per U.S.E.P.A. Tier IV and
E.U. Stage III B. 179 kW (240 bhp) at 2500 rpm.
Maximum torque: 990 N-m (730 ft lb) at 1500 rpm. Tires
Fuel requirement: Maximum of 15 ppm sulphur
content (Ultra Low Diesel Fuel). 29.5 x 25 - 28PR bias earthmover type.
Note: Tier IV engine Required in North American and
European Union countries.
Carrier continued
*Optional equipment
Lights
Auxiliary Hoist Package (includes Model
HP30A-19G auxiliary hoist with electronic hoist
Full lighting package including turn indicators, head, drum rotation indicator, hoist drum cable follower,
tail, brake and hazard warning lights. 152 m (500 ft) of 19 mm (3/4 in) 35 X 7 class wire
rope, auxiliary single sheave boom nose.
Maximum speed Auxiliary Light and Convenience Package: includes
superstructure mounted amber flashing light,
37 km/h (23 mph). in-cab LMI light bar, and dual base boom mounted
floodlights, rubber mat for stowage trough
Gradeability (theoretical) “CE” Mark Conformance (sound abatement
foam kits, 3rd wrap indicator, emergency auxiliary
130% (Based on 42 388 kg [93,447 lb] GVW) 29.5 steering, dual axis joystick controllers)
x 25 tires, pumps engaged, 33,6 m (110 ft) boom, Cross axle differential locks (front and rear)
bi-fold extension, aux. hoist and cable, and 65 USt Manual pump disconnect
hook block.
Pintle hook - rear
360⁰ NYC style positive swinglock
Miscellaneous standard equipment
PAT event recorder
Full width steel fenders, full length steel decking, dual Hydraulic removable counterweight
rear view mirrors, hook block tiedown, electronic 3rd wrap indicator with function lockout for main
back-up alarm, light package, front stowage well, hoist or main and auxiliary hoist
tachometer, rear wheel position indicator, 36,000
BTU hot water heater, air conditioning package with Wireless windspeed indicator
28,500 BTU hydraulic driven air conditioning, hoist
mirrors, engine distress A/V warning system. Auxiliary
hoist control valve arrangement (less hoist). Cold start
aid and immersion type engine block heater, 120V
1500 watt. Hoist access platform, CraneSTAR asset
management system, Outrigger position monitoring
system.
29.5 -2 5 14 961 mm 15 368 mm 12 460 mm 11 732 mm 11 342 mm 9004 mm 7662 mm 10 922 m 11 153 mm 7830 mm 7099 mm 6744 mm 4368 mm 3496 mm 2499 mm
(589") (605") (491") (462") (446") (355") (302") (430") (439") (308") (280") (266") (172") (138") (98.37")
2 Wheel Steer 4 Wheel Steer
Dimensions for table are represented in milimmeters (inches). exact.
3603 mm
(11' 10")
2252 mm
(88.65")
3334 mm
(131.25")
Carrier width
3175 mm (125.00")
Retracted
5283 mm (208.00")
Mid Extend
A H 7112 mm (280.00")
Track Full Extend
E
Outside
Turning Radius
D
Outside Curb
C Tailswing
Clearance 26° G
F 26° R4161 mm
Inside Turning Inside Curb (163.80")
Radius Clearance
Weights
GVW Front Rear
kg lb kg lb kg lb
Basic Machine: Including 110 ft main boom, main hoist with 500
ft of wire rope, auxiliary hoist with 500 ft of wire rope, full pinned 40 381 89 024 18 495 40,773 21 887 48,251
counterweight, full Decking, A/C, and hoist access platform
ADD: 60 t (65 USt) 5-sheave hookblock stowed in trough 480 1280 480 1280 0 0
ADD: 7,5 t (8.3 USt) headache ball tied to O/R cable 161 355 262 578 -101 -223
Grove RT765E-2 7
Working range
160
33' Ext.
150
140
130
110
50° 90
100
90 80
40°
80 70
30° 60
70
50
60
20° 40
50
36
40
10°
30
78° Max
boom
20
angle
0°
10
0
160 140 120 100 80 60 40 20
150 130 110 90 70 50 30 10 Axis of
rotation
Operating radius in feet from axis of rotation
THIS CHART IS ONLY A GUIDE AND SHOULD NOT BE USED TO OPERATE THE CRANE.
8 The individual crane’s load chart, operating instructions and other instructional plates must be read and understood prior to operating the crane
Working range
160
150
140
120 110
70°
60° 100
110
100 50° 90
80
90
40°
80 70
30° 60
70
60 50
20° 40
50
36
40
10° 78° Max
30
boom
20 angle
0°
10
0
180 160 140 120 100 80 60 40 20
170 150 130 110 90 70 50 30 10 Axis of
rotation
Operating radius in feet from axis of rotation
THIS CHART IS ONLY A GUIDE AND SHOULD NOT BE USED TO OPERATE THE CRANE.
Grove RT765E-2 The individual crane’s load chart, operating instructions and other instructional plates must be read and understood prior to operating the crane 9
Working range
110 ft main boom with two inserts and 33 ft - 56 ft bi-fold swingaway
180
170
160
150
Height from ground in feet
140
130
120 110
70°
60° 100
110
100 50° 90
90 80
40°
80 70
60
70 30°
50
60
20° 40
50 36
40
10° 78° Max
30 boom
angle
20
10 0°
0
200 180 160 140 120 100 80 60 40 20
190 170 150 130 110 90 70 50 30 10 Axis of
rotation
THIS CHART IS ONLY A GUIDE AND SHOULD NOT BE USED TO OPERATE THE CRANE.
10 The individual crane’s load chart, operating instructions and other instructional plates must be read and understood prior to operating the crane
Load chart
Counterweight Outriggers
Radius #0001
in Main boom length in feet
feet
36 40 50 **60 70 80 90 100 110
130,000 90,300 90,300 *62,500
10
(69.5) (71.5) (75.5) (78)
112,500 90,300 90,300 62,500 *40,200
12
(65.5) (68.5) (73) (76.5) (78)
93,250 90,300 90,250 62,500 40,200 *40,200
15
(60) (63.5) (69.5) (73.5) (76) (78)
71,550 71,500 71,300 62,500 40,200 40,200 40,200 *36,900
20
(49.5) (55) (63) (68) (71.5) (74.5) (78) (78)
56,650 56,600 56,350 53,650 40,200 40,200 37,950 34,900 *25,150
25
(36.5) (45) (56) (63) (67) (70.5) (73) (75) (78)
43,500 44,300 43,950 43,650 40,200 36,050 32,750 30,200 25,150
30
(11.5) (32) (48.5) (57.5) (62.5) (66.5) (69.5) (72) (74)
33,550 33,700 34,700 31,450 28,550 26,400 24,700
35
(40) (51.5) (58) (62.5) (66) (69) (71.5)
25,800 26,150 26,900 27,700 25,200 23,300 21,800
40
(28) (44.5) (52.5) (58.5) (62.5) (66) (68.5)
20,650 21,450 22,300 22,400 20,700 19,400
45
(36.5) (47) (54) (59) (62.5) (65.5)
16,550 17,400 18,250 19,100 18,550 17,350
50
(26.5) (41) (49.5) (55) (59.5) (62.5)
14,300 15,150 16,000 16,400 15,600
55
(33.5) (44) (51) (56) (60)
11,800 12,700 13,550 13,950 14,100
60
(23.5) (38.5) (46.5) (52.5) (56.5)
10,700 11,550 11,950 12,300
65
(31.5) (41.5) (48.5) (53.5)
9010 9920 10,250 10,650
70
(22.5) (36) (44) (50)
8510 8890 9250
75
(29.5) (39.5) (46)
7260 7690 8050
80
(21) (34.5) (42.5)
6620 7010
85
(28.5) (38)
5630 6100
90
(20) (33)
5240
95
(27)
4480
100
(19.5)
Minimum boom angle (° ) for indicated length (no load) 0
Maximum boom length (ft ) at 0° boom angle (no load) 110
NOTE: ( ) Boom angles are in degrees.
#LMI operating code. Refer to LMI manual for operating instructions.
*This capacity is based on maximum boom angle.
Lifting capacities at zero degree boom angle
Boom Main boom length in feet
angle 36 40 50 **60 70 80 90 100 110
30,350 25,700 17,950 13,050 10,050 7790 6300 4900 3900
0°
(30.1) (34.2) (44.2) (54.6) (64.2) (74.2) (84.2) (94.2) (104.2)
NOTE: ( ) Reference radii in feet. 80039604
** Boom length is with inner-mid fully extended and outer-mid & fly fully retracted.
THIS CHART IS ONLY A GUIDE AND SHOULD NOT BE USED TO OPERATE THE CRANE.
Grove RT765E-2 The individual crane’s load chart, operating instructions and other instructional plates must be read and understood prior to operating the crane 11
Load chart
ON OUTRIGGERS FULLY EXTENDED - 360°
NOTES:
Counterweight Outriggers 1. All capacities above the bold line are based on
structural strength of boom extension.
36 ft - 110 ft 33 ft - 56 ft 14,365 lb 23 ft 4 in 360°
(100%) 2. 33 ft and 56 ft boom extension lengths may be
used for single line lifting service.
3 3 ft LE NGTH 56 ft LE NGTH
3. For main boom lengths less than 110 ft with
Radius
0° 25° 45° 0° 25° 45° the boom extension erected, the rated loads are
in
OFFSET OFFSET OFFSET OFFSET OFFSET OFFSET determined by boom angle. Use only the column
feet
#0021 #0022 #0023 #0041 #0042 #0043 which corresponds to the boom extension length
and offset for which the machine is set up. For
12,900 boom angles not shown, use the rating of the next
30
(78) lower boom angle.
12,900 *8330
35
(76.5) (78) 4. WARNING: Operation of this machine with
12,900 *10,850 8330 heavier loads than the capacities listed is strictly
40 prohibited. Machine tipping with boom extension
(74.5) (78) (77.5)
occurs rapidly and without advance warning.
12,900 10,450 *7410 8330
45
(72) (76.5) (78) (76)
5. Boom angle is the angle above or below
12,100 10,000 7200 8330 horizontal of the longitudinal axis of the boom base
50
(70) (74.5) (77.5) (74) section after lifting rated load.
11,100 9220 6990 8250 *5300
55 6. Capacities listed are with outriggers fully
(68) (72.5) (75.5) (72) (78)
extended and vertical jacks set only.
10,100 8550 6800 7540 5140
60
(65.5) (70) (73) (70.5) (77.5)
7. When lifting over the main boom nose with 33 ft
9130 7930 6650 7160 5100 *3860 or 56 ft extension erected, the outriggers must be
65
(63.5) (67.5) (70.5) (68.5) (75.5) (78) fully extended or 50% extended (17 ft spread).
8460 7380 6490 6820 5100 3790
70
(61) (65.5) (68) (66.5) (73.5) (77.5)
7840 6900 6370 6300 4800 3660
75
(58.5) (63) (65.5) (64.5) (71.5) (75.5)
7230 6470 6110 5810 4580 3550
80
(56) (60.5) (63) (62.5) (69.5) (73)
6690 6070 5780 5370 4470 3,450
85
(53.5) (58) (60) (60.5) (67) (71)
6,140 5720 5480 4980 4330 3410
90
(51) (55.5) (57.5) (58.5) (65) (68.5)
5670 5400 5200 4,630 4070 3,300
95
(48.5) (52.5) (54.5) (56.5) (63) (66.5)
5150 5100 4950 4320 3830 3260
100
(45.5) (49.5) (51.5) (54) (60.5) (64)
4650 4760 4650 4040 3620 3220
105
(42.5) (46.5) (48) (52) (58.5) (61.5)
4,070 4430 3770 3410 3180
110
(39.5) (43) (49.5) (56) (59)
3540 3930 3540 3230 3060
115
(36) (39.5) (47.5) (53.5) (56)
3060 3400 3310 3050 2940
120
(32) (35) (45) (50.5) (53)
2630 2920 3070 2890 2800
125
(27) (30) (42) (48) (50)
2230 2770 2730
130
(21.5) (39.5) (45)
2400 2590
135
(36.5) (41.5)
2050 2410
140
(33) (38)
1720 2040
145
(29) (33.5)
1420
150
(24.5)
Minimum boom angle
(°) for indicated length 19 29 47 23 32 49
(no load)
Maximum boom length
(ft) at 0° boom angle 1 00 90
(no load)
NOTE: ( ) Boom angles are in degrees. 80039607
#LMI operating code. Refer to LMI manual for operating instructions.
*This capacity is based upon maximum boom angle.
THIS CHART IS ONLY A GUIDE AND SHOULD NOT BE USED TO OPERATE THE CRANE.
12 The individual crane’s load chart, operating instructions and other instructional plates must be read and understood prior to operating the crane
Load chart
Counterweight Outriggers
NOTES:
36 ft - 110 ft 14,365 lb 23 ft 4 in 360° 1. All capacities above the bold line are based on structural
56 ft 20 ft
(100%) strength of boom extension.
THIS CHART IS ONLY A GUIDE AND SHOULD NOT BE USED TO OPERATE THE CRANE.
Grove RT765E-2 The individual crane’s load chart, operating instructions and other instructional plates must be read and understood prior to operating the crane 13
Load ON
chart
OUTRIGGERS FULLY EXTENDED - 360°
Counterweight Outriggers
NOTES:
36 ft - 110 ft 56 ft 40 ft 14,365 lb 23 ft 4 in 360° 1. All capacities above the bold line are based on structural
(100%) strength of boom extension.
THIS CHART IS ONLY A GUIDE AND SHOULD NOT BE USED TO OPERATE THE CRANE.
14 The individual crane’s load chart, operating instructions and other instructional plates must be read and understood prior to operating the crane
STATIONARY CAPACITIES - 360°
Load chart
NOTES TO ALL RUBBER CAPACITY CHARTS:
Counterweight 1. Capacities are in pounds and do not exceed 75% of tipping
loads as determined by test in accordance with SAE J765.
36 ft - 110 ft 14,365 lb Stationary 360°
2. Capacities are applicable to machines equipped with 29.5
x 25 (28 or 34 ply General/Titan, Denman Rock Plus, Denman
#9005 Broadway and Advance bias plus ply) tires at 65 psi cold
Radius inflation pressure.
in Main boom length in feet
feet 3. Capacities appearing above the bold line are based on
36 40 50 *60 70 structural strength and tipping should not be relied upon as
45,300 39,700 a capacity limitation.
10
(69.5) (71.5)
4. Capacities are applicable only with machine on firm level
41,500 39,700 29,600 surface.
12
(66) (68.5) (73)
5. On rubber lifting with boom extensions not permitted.
32,450 31,750 26,450 20,900
15
(60) (63.5) (69.5) (73.5) 6. For pick and carry operation, boom must be centered over
front of machine, mechanical swing lock engaged and load
19,200 18,850 18,750 18,550 17,300
20 restrained from swinging.
(50) (55) (63) (68) (71.5)
12,600 12,350 12,250 12,050 12,550 7. Axle lockouts must be functioning when lifting on rubber.
25
(36.5) (44.5) (56) (63) (67)
8. All lifting depends on proper tire inflation, capacity and
8650 8530 8250 8150 8710 condition. Capacities must be reduced for lower tire inflation
30 pressures. See lifting capacity chart for tire used. Damaged
(11.5) (31.5) (48.5) (57) (62.5)
tires are hazardous to safe operation of crane.
5600 5450 6170
35
(39.5) (51) (57.5) 9. Creep - not over 200 ft of movement in any 30 minute
period and not exceeding 1 mph.
3700 3410 4300
40
(28) (44) (52)
1760 2850
45
(36) (46.5)
1250
50
(40)
Minimum boom angle (°) for indicated length
35 39
(no load)
Maximum boom length (ft) at 0° boom angle
50
(no load)
NOTE: ( ) Reference boom angles in degrees.
THIS CHART IS ONLY A GUIDE AND SHOULD NOT BE USED TO OPERATE THE CRANE.
Grove RT765E-2 The individual crane’s load chart, operating instructions and other instructional plates must be read and understood prior to operating the crane 15
Load charts
Counterweight Counterweight
36 ft - 110 ft 14,365 lb Pick and carry Over 36 ft - 110 ft 14,365 lb Creep speed Over
up to 2.5 mph front front
29.5 x 25 tires
#9006 #9030
Radius Radius
in Main boom length in feet in Main boom length in feet
feet feet
36 40 50 *60 70 36 40 50 *60 70
47,200 44,000 34,000 47,200 44,000 34,000
10 10
(69.5) (71.5) (75.5) (69.5) (71.5) (75.5)
43,450 42,500 34,000 28,500 47,200 44,000 34,000 28,500
12 12
(66) (68.5) (73) (76.5) (66) (68.5) (73) (76.5)
35,900 35,200 34,000 28,500 21,350 43,250 42,500 34,000 28,500 21,350
15 15
(60) (63.5) (69.5) (73.5) (75.5) (60) (63.5) (69.5) (73.5) (75.5)
27,000 26,650 26,300 26,500 21,350 32,950 32,600 32,250 28,500 21,350
20 20
(50) (55) (63) (68) (71.5) (50) (55) (63) (68) (71.5)
20,750 20,550 20,500 20,550 21,300 25,450 24,850 25,250 25,250 21,350
25 25
(36.5) (44.5) (56) (63) (67) (36.5) (44.5) (56) (63) (67)
16,150 16,100 16,200 16,200 17,000 17,850 17,250 17,800 18,050 19,000
30 30
(11.5) (31.5) (48.5) (57) (62.5) (11.5) (31.5) (48.5) (57) (62.5)
12,850 12,850 13,750 12,950 13,300 14,300
35 35
(39.5) (51) (57.5) (39.5) (51) (57.5)
9550 9970 10,950 9550 9970 10,950
40 40
(28) (44) (52) (28) (44) (52)
7470 8470 7470 8470
45 45
(36) (46.5) (36) (46.5)
5550 6540 5550 6540
50 50
(26) (40) (26) (40)
5010 5010
55 55
(33) (33)
3760 3760
60 60
(23) (23)
Minimum boom angle (°) for indicated length (no load) 0 Minimum boom angle (°) for indicated length (no load) 0
Maximum boom length (ft) at 0° boom angle (no load) 70 Maximum boom length (ft) at 0° boom angle (no load) 70
NOTE: ( ) Reference boom angles in degrees. NOTE: ( ) Reference boom angles in degrees.
Lifting capacities at zero degree boom angle Lifting capacities at zero degree boom angle
Boom Main boom length in feet Boom Main boom length in feet
angle 36 40 50 *60 70 angle 36 40 50 *60 70
16,100 12,950 7,390 4,140 2,880 17,750 12,950 7,390 4,140 2,880
0° 0°
(30.1) (34.2) (44.2) (54.6) (64.2) (30.1) (34.2) (44.2) (54.6) (64.2)
Note: ( ) Re fe re nce radii in fee t. 8003 9613 Note : ( ) Re fe re nce radii in fe e t. 8003 9612
#LMI operating code. Refer to LMI manual for instructions. #LMI operating code. Refer to LMI manual for instructions.
*60 ft. boom length is with inner-mid extended and outer-mid & fly *60 ft. boom length is with inner-mid extended and outer-mid & fly
retracted. retracted.
NOTES TO ALL RUBBER CAPACITY CHARTS: 5. On rubber lifting with boom extensions not permitted.
1. Capacities are in pounds and do not exceed 75% of tipping loads
as determined by test in accordance with SAE J765. 6. For pick and carry operation, boom must be centered over front of
machine, mechanical swing lock engaged and load restrained from
2. Capacities are applicable to machines equipped with 29.5 x 25 swinging.
(28 or 34 ply General/Titan, Denman Rock Plus, Denman Broadway
and Advance bias plus ply) tires at 65 psi cold inflation pressure. 7. Axle lockouts must be functioning when lifting on rubber.
3. Capacities appearing above the bold line are based on structural 8. All lifting depends on proper tire inflation, capacity and condition.
strength and tipping should not be relied upon as a capacity Capacities must be reduced for lower tire inflation pressures. See
limitation. lifting capacity chart for tire used. Damaged tires are hazardous to safe
operation of crane.
4. Capacities are applicable only with machine on firm level
surface. 9. Creep - not over 200 ft of movement in any 30 minute period and not
exceeding 1 mph.
THIS CHART IS ONLY A GUIDE AND SHOULD NOT BE USED TO OPERATE THE CRANE.
16 The individual crane’s load chart, operating instructions and other instructional plates must be read and understood prior to operating the crane
Load handling
Weight reductions for load handling devices Line pulls and reeving information
33 ft - 56 ft : Folding boom extension: Permissable Nominal
Hoists Cable specs line pulls cable length
Without block With 355 lb 19 mm (3/4 in)
or ball overhaul ball 6 x 37 class, EIPS,
IWRC Special
*33 ft extension (erected) 3850 lb 5980 lb Main Flexible 16,800 lb 500 ft
Min. breaking
strength
*56 ft extension (erected) 8620 lb 12,170 lb 58,800 lb
Over Over
CG of load
front rear
Front
See note
at bottom
Over Centerline
side rotation
D6-829-013434
Bold lines determine the limiting position of any laod for operation withing working areas indicated.
THIS CHART IS ONLY A GUIDE AND SHOULD NOT BE USED TO OPERATE THE CRANE.
Grove RT765E-2 The individual crane’s load chart, operating instructions and other instructional plates must be read and understood prior to operating the crane 17
Symbols glossary
Extension
Boom extension Hydraulic system Steering
THIS CHART IS ONLY A GUIDE AND SHOULD NOT BE USED TO OPERATE THE CRANE.
18 The individual crane’s load chart, operating instructions and other instructional plates must be read and understood prior to operating the crane
Notes
THIS CHART IS ONLY A GUIDE AND SHOULD NOT BE USED TO OPERATE THE CRANE.
Grove RT765E-2 The individual crane’s load chart, operating instructions and other instructional plates must be read and understood prior to operating the crane 19
Manitowoc Cranes
Regional headquarters
Americas Europe, Middle East, Africa China Greater Asia-Pacific
Manitowoc, Wisconsin, USA Ecully, France Shanghai, China Singapore
Tel: +1 920 684 6621 Tel: +33 (0)4 72 18 20 20 Tel: +86 21 6457 0066 Tel: +65 6264 1188
Fax: +1 920 683 6277 Fax: +33 (0)4 72 18 20 00 Fax: +86 21 6457 4955 Fax: +65 6862 4040
Shady Grove, Pennsylvania, USA
Tel: +1 717 597 8121
Fax: +1 717 597 4062
Regional offices
Americas
Brazil
China
Beijing
Factories This document is non-contractual. Constant improvement and engineering progress
make it necessary that we reserve the right to make specification, equipment, and price
Brazil changes without notice. Illustrations shown may include optional equipment and
Alphaville Chengdu accessories and may not include all standard equipment.
Alphaville
Mexico Guangzhou
China
Monterrey Xian
TaiAn
Chile
Zhangjiagang
Santiago Greater Asia-Pacific
France
Australia
Charlieu
Europe, Middle East, Adelaide
Moulins
Africa Brisbane
Germany
Czech Republic Melbourne
Wilhelmshaven
Netvorice Sydney
India
France India
Pune
Baudemont Calcutta
Italy
Cergy Chennai
Niella Tanaro
Decines Delhi
Portugal
Germany Hyderabad
Baltar
Langenfeld Pune
Fânzeres
Hungary Korea
Slovakia
Budapest Seoul
Saris
Italy Philippines
USA
Lainate Makati City
Manitowoc
Netherlands Singapore
Port Washington
Breda
Shady Grove
Poland
Warsaw
Portugal
Baltar
Russia
Moscow
U.A.E.
Dubai
U.K.
Buckingham
©2011 Manitowoc
Form No.RT765E-2 PG
Part No.10-009-2M-0911 www.manitowoc.com