Professional Documents
Culture Documents
Kf6 Catalogo Nuevo
Kf6 Catalogo Nuevo
PARTS LIST
Section VI - Page # 4
UNIVERSAL TOP CAP MOUNTING
KF6QT HYDRARAM
4 K10194 24 Washer
Inch Milimeter
A 4.50 114.3 Boss Hole Diameter
B 17.00 431.8 Boss Width (Pin Length)
C 10.50 266.7 Boss Inside Spacing
D 14.00 355.6 Pin Center to Center
Section VI - Page # 5
T-BOX MOUNTING
And DAMPER SYSTEM
KF6QT HYDRARAM
Section VI - Page # 6
T-BOX MOUNTING
And DAMPER SYSTEM
KF6QT HYDRARAM
7 K101032-24050 4 Bolt
8 K120132-24000 4 Locknut
9 K140112-24000 4 Washer
Inch Milimeter
A 0.866 22 Bolt Hole Diameter
B 16.929 430 Flange, Long Side
C 13.386 340 Flange, Short Side
D 14.961 380 Center to Center
E 11.417 290 Center to Center
F 5.512 140 Center to Center
G 3.397 100 Center to Center
Section VI - Page # 7
SWITCH HITCH ™ MOUNTING
KF6TLB HYDRARAM
Tractor-Loader-Backhoe Version
Section VI - Page # 8
SWITCH HITCH ™ MOUNTING
KF6TLB HYDRARAM
Tractor-Loader-Backhoe Version
ITEM PART NUMBER QUANTITY DESCRIPTION
Section VI - Page # 9
FLANGED SIDE PLATE MOUNTING
KF6FSP HYDRARAM
Section VI - Page # 10
FLANGED SIDE PLATE MOUNTING
KF6FSP HYDRARAM
KENT's Qt and FSP Hammers use the same Top Caps. KENT can also supply many
other top caps to match OEM specifications. Contact KENT's engineering department
to determine which version to use with the carrier and attachment required. You must
use an OEM style top cap with quick attachment and pin grabbing systems.
Section VI - Page # 11
MOUNTING PIN KIT PARTS LIST
KF6 HYDRARAM
For KF6TLB and KF6FSP Versions
Using KENT's Universal Mounting System
KENT's Qt and FSP Hammers use the same Top Caps. KENT can also supply many
other top caps to match OEM specifications. Contact KENT's engineering department
to determine which version to use with the carrier and attachment required. You must
use an OEM style top cap with quick attachment and pin grabbing systems.
Section VI - Page # 12
MOUNTING PIN KIT PARTS LIST
KF6 HYDRARAM
For KF6TLB and KF6FSP Versions
Using KENT's Universal Mounting System
Serial Number
Section VI - Page # 13
TWO-POSITION (PIN-ON)
QUICK ATTACH BRACKET
For KF6TLB HYDRARAM
NOTE: The bushings are installed on the outside of the hammer frame, and the pins extend through the
attachment breacket. This configuartion requires extra-long pins as noted.
Section VI - Page # 14
BOLTED ONE-PIECE RIGID
QUICK ATTACH BRACKET
For KF6QT or KF6FSP HYDRARAMS
Section VI - Page # 15
OPEN STYLE ONE-PIECE RIGID
QUICK ATTACH BRACKET
For KF6B HYDRARAM
Section VI - Page # 16
SERVICE TOOL KIT
P/N KF690001
Kent includes a tool kit with every new hydraulic breaker. This tool kit
contains many of the special tools and wrenches required to perform normal
maintenance or repairs on the breaker. This is a basic tool kit, and is by no
means complete or comprehensive, but it does contain some specialized tools,
and wrench sizes not commonly found in the field. The following illustration
depicts a typical tool kit and its contents:
Section VI - Page # 17
Section VI - Page # 18