Professional Documents
Culture Documents
No part of this document may be reproduced in any form or by any means (including electronic storage and retrieval or translation into a foreign language) without
prior agreement and written consent from Spartek Systems Inc. as governed by international copyright laws.
Disclaimer
The material contained in this document is provided “as is” and is subject to being changed without notice in future editions. The material in this manual should be
considered a guideline, but is no substitute for proper training and supervision by qualified personnel.
The information and guidelines contained herein have been compiled from sources believed to be reliable, representing industry best practices. There is no warranty,
guarantee, or representation, either expressed or implied by Spartek Systems Inc. to the correctness or sufficiency of any representation contained in this manual.
While Spartek Systems Inc. endeavors to ensure these guidelines are accurate at the time of their preparation, it takes no responsibility for matters arising from
changed circumstances or information or material that may have become available after the issued or reviewed date.
Spartek Systems Inc. shall not be liable for errors or for incidental or consequential damages in connection with the furnishing, use, or performance of this document
or any information contained herein.
The hardware and/or software described in this document are furnished under a license and may be used or copied only in accordance with the terms of such license.
2
Table of Contents
Introduction ........................................................................................ 5 Multi-Finger Calipers (MFC) ............................................................... 49
Spartek Systems ................................................................................ 6 MFC 24 Finger Tool String .................................................................. 50
About Us ...................................................................................... 6 MFC 24 Finger Tool String – Sour Service .......................................... 51
Customer Service Guidance ......................................................... 6 MFC 40 Finger Tool String .................................................................. 52
Contact Us ................................................................................... 6 SS8122 / SS8150 Hybrid SRO Telemetry 50K ..................................... 53
Surface Equipment .............................................................................. 7 SS8191 Cablehead Tension Tool ........................................................ 54
SS8211 Gamma Ray / Casing Collar Locator ...................................... 55
SS6702 SRO Panel .............................................................................. 8
SS8736 1.688” Knuckle Joint .............................................................. 56
SS6720 SRO Panel and Plotter Systems ............................................. 9
SS8720 PL In-Line Roller Centralizer (1.688”) .................................... 57
SS6800 Line Management System (LMS) ........................................... 10
SS9205 In-Line Roller Centralizer (2.75”) ........................................... 58
Printrex Thermal Line Printers ........................................................... 11
SS9102 Multi-Finger Caliper – 24 Finger ............................................ 59
SDS Warrior Logging Panel and Software .......................................... 12
SS9101 Multi-Finger Caliper – 40 Finger ............................................ 60
SS6905 Memory Controller Interface Module ................................... 13
SS9103 Multi-Finger Caliper – 60 Finger ............................................ 61
Accessories ........................................................................................ 14
SS8950 Signal Adapter Module (SAM) – Sour Service ........................ 62
Cables – BNC to BNC .................................................................... 14
SS9104 Multi-Finger Caliper – 24 Finger – Sour Service ..................... 63
Cables – Tool Cables .................................................................... 14
Accessories ........................................................................................ 64
Cables – Power / Adapter ............................................................ 14
Cables – USB A/B ......................................................................... 14 Battery Pack Housings (Standard) ...............................................64
Depth Encoder ............................................................................. 15 Battery Packs ...............................................................................64
Depth Splitter Box........................................................................ 15 Calibrators ...................................................................................65
Depth Encoder Cables .................................................................. 16 Crossover (1.375” to 1.688”) .......................................................66
Depth Simulator .......................................................................... 16 Crossover (1.688” to 1.375”) .......................................................66
Documents .................................................................................. 17 Bullnose / Crossover ....................................................................66
Logging Software ........................................................................ 17 Elastomer Redress Kits.................................................................67
Lubricants .................................................................................... 18 Miscellaneous Tools.....................................................................67
Shipping Cases ............................................................................. 18 Shipping Case ..............................................................................68
Shipping Case – SS6702 Surface Panel ......................................... 19 Shipping Case (MFC) ...................................................................68
SS1008 200C Battery Depassivation Box ..................................... 19 Thread Protectors (GO) ................................................................68
Tool Stands .................................................................................. 19 Thread Protectors (Spartek PLT) ..................................................69
Tool Vise-Clamp (Alumninum) ..................................................... 19 Cement Bond Logging Tools (SCBT) – SRO .......................................... 71
Warrior Line Card Interface ......................................................... 20 Tool String Configurations ................................................................. 72
Wireline Simulator ....................................................................... 20
SS9212 Segmented Cement Bond (1.688”) ........................................ 73
SS6916 PLT Tool Breakout Box..................................................... 21
SS9248 E-Line Roller Centralizer (1.688”) .......................................... 74
SS6917 PLT Memory Tool Volt / Amp Monitor Box ...................... 21
SS9249 In-Line Mid Roller Centralizer (1.688”) .................................. 75
SS6918 PLT Sonde Tool Volt / Amp Monitor Box.......................... 22
SS9220 Segmented Cement Bond (2.75”) .......................................... 76
Standalone Analog Tools ................................................................... 23 SS9228 E-Line Roller Centralizer (2.75”) ............................................ 77
SS8245 Analog GR/CCL ...................................................................... 24 SS9229 In-Line Mid Roller Centralizer (2.75”) .................................... 78
SS8246 Analog HTHP GR/CCL ............................................................. 25 SS9230 Segmented Cement Bond (3.50”) .......................................... 79
SS8716 PL E-Line Centralizer .............................................................. 26 SS9238 E-Line Roller Centralizer (3.50”) ............................................ 80
Casing Inspection Tools (CIT) .............................................................. 27 SS9239 In-Line Mid Roller Centralizer (3.50”) .................................... 81
Casing Inspection Tool ....................................................................... 28 Cement Bond Logging Tools (SCBT) - Memory .................................... 83
MFL 375 Tool String– Telemetry Only – Low Deviation ..................... 29 Tool String Configurations ................................................................. 84
MFL 450 Tool String– Telemetry Only – Low Deviation ..................... 30 SS8122 / SS8150 Hybrid SRO Telemetry 50K ..................................... 86
MFL 575 Tool String– Telemetry Only – Low Deviation ..................... 31 SS8191 Cablehead Tension Tool ........................................................ 86
MFL 575 Tool String– Telemetry Only – High Deviation .................... 32 SS8736 1.688” Knuckle Joint .............................................................. 88
MFL 800 Tool String– Telemetry Only – High Deviation .................... 33 SS8211 Gamma Ray / Casing Collar Locator ...................................... 89
SS8111 SRO / Telemetry .................................................................... 34 SS8720 PL In-Line Roller Centralizer (1.688”) .................................... 90
SS8191 Cablehead Tension Tool ........................................................ 35 SS9240 Segmented Cement Bond (1.688”) ........................................ 91
SS8225 Gamma Ray ........................................................................... 36 SS9249 In-Line Mid Roller Centralizer (1.688”) .................................. 92
SS8130 CIT Memory Assembly ........................................................... 37 SS9225 Segmented Cement Bond (2.75”) .......................................... 93
SS9000 CIT MFL 375 ........................................................................... 38 SS9205 In-Line Roller Centralizer (2.75”) ........................................... 94
SS9020 CIT MFL 450 ........................................................................... 39 SS9229 In-Line Mid Roller Centralizer (2.75”) .................................... 95
SS9030 CIT MFL 575 ........................................................................... 40 Accessories ........................................................................................ 96
SS9040 CIT MFL 800 ........................................................................... 41 Battery Pack Housings (Standard) ...............................................96
CIT MFL Bottom Adapter ................................................................... 42 Battery Packs ...............................................................................96
CIT Slip-Over Centralizers .................................................................. 43 Crossover (1.375” to 1.688”) .......................................................97
CIT High-Deviation Slip-Over Centralizers .......................................... 44 Crossover (1.688” to 1.375”) .......................................................97
Accessories ........................................................................................ 45 Bullnose / Crossover ....................................................................97
MFL Casing Extension Kits ........................................................... 45 Elastomer Redress Kits.................................................................98
Pad Protection Sleeves ................................................................ 45 Miscellaneous Tools.....................................................................98
Elastomer Redress Kits ................................................................ 45 Shipping Case ..............................................................................99
Consumables ............................................................................... 46 Shipping Case (SCBT) ..................................................................99
Hand Tools Kit ............................................................................. 47 Thread Protectors (Spartek PLT) ..................................................99
Thread Protectors ........................................................................ 47 Warranty ......................................................................................... 101
Introduction
5
Introduction
Spartek Systems
Spartek Systems
Spartek Systems strives to aggressively research and develop state of the art technologies to enhance our customers’ ability to evaluate, monitor and exploit oil and
gas assets. To ensure customer satisfaction by providing outstanding technical support and high-quality products at competitive prices.
About Us
Founded in Sylvan Lake, Alberta, Canada, Spartek Systems has over 100
employees worldwide. Our goal is to provide the industry with cost effective
solutions to solving reservoir problems. The Spartek team is dedicated to
providing their best efforts to ensure a safe working environment, delivering
high quality products with a goal of zero defects, and providing outstanding
customer technical support.
Sylvan Lake is our` center for Research and Development, and
Manufacturing. Our key staff has over 120 years of industry experience in
developing and deploying subsurface and surface equipment. We employ the
latest technologies in the design and development of our products. Our
development process begins with understanding our customer's
requirements and continues with outstanding technical support throughout
the life of the product
Presently Spartek Systems offers a wide range of memory and surface Head Office – Sylvan Lake, Alberta, Canada
readout pressure & temperature recorders, a complete suite of production
logging instrumentation, casing inspection technology, multi-cycle shut in
tool, permanent monitoring systems, perforating memory triggers and a full
range of surface and subsurface accessories to meet your measurement
needs.
Surface Equipment
The CE certified SRO PL Panel is the available option for the Specifications
Surface Acquisition section of the Production Logging Tool. Width 19.0"
Depth 15.0"
• Displays Depth and Line-speed on easy to see blue VFD
Height 3.25" (~ 2U)
• Light-weight, 19" x 24" rack mount portable chassis
Weight 12.52 lbs
• Interfaces the Spartek Telemetry tool with a PC
Mounting 19" Rack Mount
• USB 1.0/2.0 communication interface (2m USB A/B cable
110 / 220 V AC
included) Operating Voltage
60 / 50 Hz
• Operates with conventional or sour-service wirelines Operating Current 2A
• Up to 25Kft (7,600m) long
• Can acquire up to two 4-20mA analog surface channels
• CE certification
Accessories
Item Description Item Number
BNC-BNC Patch Cable - 50C - 1 m (3 ft) 10000297
Printrex Thermal Line Printer Accessory - Rack Mount Version - Rail Kit 10018899
The SRO PL Panel & Plotter is the available option for the Specifications
Surface Acquisition section of the Production Logging Tool. Width 24.5"
Depth 20.5"
• Portable, rugged and moisture resistant enclosure
Height 9.7"
suitable for shipping
Weight 60 lbs
• End covers are easily removed for quick set up and
110 / 220 V AC
operation Operating Voltage
60 / 50 Hz
• Industry standard Printrex Thermal black/white or color
Operating Current 5A
Line Plotter
• Spartek SS6702 PL SRO Panel included
• Displays Depth and Line-speed on easy to see blue VFD
• USB 1.0/2.0 communication interface
• Interfaces the Spartek Telemetry tool with the PC
Accessories
Item Description Item Number
BNC-BNC Patch Cable - 50C - 1 m (3 ft) 10000297
Accessories
Item Description Item Number
Cable - Depth Encoder - Non-Molded - 15 ft 10006534
1
Or internal battery pack.
2
With Spartek/BEI encoder connected.
www.sparteksystems.com 1 Sep 2023 Well Integrity Catalog
10
Surface Equipment
The Printrex 823DL/G black/white and C9201 color thermal- Desktop (B/W only)
line plotters are available for used for printing fan-fold log Width 12.3"
prints. Both plotters are available in either a rack mount or Depth 12.0"
desktop version. Height 4.87"
Weight 21.0 lbs
• Rack mount version mounts in any standard 19"wide x
Rack Mount (B/W & Color)
3U rack system
• Rugged design Width 19.0"
• Compatible with the SparWorks software application Depth 16.12"
• Accepts fan-fold or continuous role thermal paper Height (3U) 5.25"
Weight 22.0 lbs
• Cables included
• Used throughout the logging industry
• USB 2.0 interface and network connectivity
• Universal AC input
• Paper output stacker/basket and extra paper also
available2
Accessories
Item Description Item Number
Printrex Thermal Line Printer Accesory - Desktop Version - Paper 10024733
Printrex Thermal Line Printer Accessory - Desktop Version - Paper Input 10020121
Printrex Thermal Line Printer Accessory - Rack Mount Version - Paper 10020122
Printrex Thermal Line Printer Accessory - Rack Mount Version - Rail Kit 10018899
Printrex Thermal Line Printer Consumable - Paper - Roll (6 Rolls x 150ft per Case) 10020123
1
Color desktop plotter is available on special request only.
2
Upon request only.
www.sparteksystems.com 1 Sep 2023 Well Integrity Catalog
11
Surface Equipment
PL - Logging Panel - Warrior (incl. data acquisition boards) - 220VAC Operation 10018355
Accessories
Item Description Item Number
Software - Warrior 8 - Companion Key (dongle) 10027782
Software - Warrior 8 - Full Access Cased Hole - With Real Time Acquisiton 10027781
Accessories
Item Description Item Number
Cable - Power Supply - Auto 12VDC source - 3 ft 10017507
Accessories
Accessories
PL - Test Cable - Nexus Plug to 4-Pin / 6-Socket KTK Cable - 10 ft - 177C 10028062
Accessories
Depth Encoder
Item Description Item Number
Optical Depth Encoder - 6 pin 10014149
Accessories
Item Description Item Number
Depth System - Adapter - Veeder Root to K-Winch Encoder Crossover Assembly 10031505
Encoder Adaptor Kit - SB - K-Winch Depth System 10030706
4 x 10029969 Screw - M4 - 0.7 x 14mm - Socket Head Cap Screw - SS
1 x 10030704 Depth System - Replacement - Bi Directional Nut
1 x 10030707 Depth System - Replacement - K-Winch to Encoder - Outer Body
1 x 10030708 Depth System - Replacement - K-Winch to Encoder - Drive Shaft
1
Additional encoder models are available on request.
www.sparteksystems.com 1 Sep 2023 Well Integrity Catalog
15
Surface Equipment
Accessories
The Depth Encoder cables connect either the Line Management System (LMS) or SRO
PL Panel to the mechanical depth encode.
• Compatible with both the Spartek SRO panel and LMS box
• 15 ft long, molded, sealed connector
• Shielded throughout and grounded on one end only (black connector)
• Connector dust-covers included
• Custom lengths up to 75 ft available
Depth Simulator
Item Description Item Number
Depth Simulator Assembly 10008633
The Depth Simulator box connects to the depth port on the Line Management System
(LMS) or SRO PL Panel and provides a method for simulating logging up or down.
Typically used for testing depth cables, SRO panels, LMS boxes and training.
Accessories
Item Description Item Number
Cable - Depth Encoder - Non-Molded - 15 ft 10006534
Accessories
Documents
Item Description Item Number
Doc - OP - SS8000 Production Logging Operation Manual - Memory Mode 10026772
All documents are available in electronic form (PDF) or bound hard copy.
Maintenance Manuals
Maintenance manuals for the Production Logging Tool are available and listed on their
respective pages. They are categorized in three levels (ML1, ML2, and ML3).
• Level 1 - focuses on maintaining the integrity of field joints and the replacement of
normal wear items in dynamic mechanical assemblies. A field technician is required
to perform these procedures after each use.
• Level 2 - focuses on maintaining the integrity of internal seals, the inspection of
internal assemblies for damage, and the replacement of normal wear items in
dynamic mechanical assemblies. A field or laboratory technician is required to
perform these procedures, in conjunction with Level 1, after six months of use.
• Level 3 - focuses on the refurbishment and/or repair of all the module level parts
and assemblies. A laboratory technician is required to perform these procedures, in
conjunction with Levels 1 & 2, every twelve to twenty-four months depending on
the frequency of use and the type of well conditions the tool module has been
exposed to.
Logging Software
Item Description Item Number
Casing Evaluation & Analysis Module (Includes SparWorks) 10028758
SparWorks is the primary software application used for acquiring and processing data
from all Spartek Systems Production Logging Tool products. The USB security software
("dongle") provides licensing protection for the software on an installation by
installation basis.
• Full support for the SRO and Memory mode PLT systems
• Full support for the LMS
• Complete software solution for acquiring, processing and presenting of Spartek PLT
data
• Import and Export LAS and ASCII data files
• No annual license fees
• Software upgrades available at no extra cost
• Microsoft Windows 98SE/ME/NT/XP/VISTA/Window 7
• The USB port dongle is automatically -detected by SparWorks
Accessories
Lubricants
Item Description Item Number
Grease - Thread Lubricant - Fastorq 70+ (16 oz Brush Top) 10013669
Shipping Cases
Item Description Dimensions (L x D x H) Slots Slot Length Slot Width Item Number
Accessories
Shipping Case for the SS6702 Surface Readout (SRO) Panel. Specifications
Width 24.4"
• Pelican brand, model 1600, PVC, water-resistant case
Depth 19.4"
• Rugged construction, latches and handle
Height 8.8"
• Lined with high-impact foam
Weight (Empty) 13.0 lbs
• Suitable for shipping on all commercial carriers
• CE certified
• Compatible with the Spartek SRO panel and LMS box
SS1008 SB - 180C / 200C - Battery Depassivation Box - 7 & 11 Pin Connector 10031902
Battery Depassivation box for 7-pin and 11-pin 200 C Lithium battery packs.
Tool Stands
Item Description Item Number
Tool Stand - 2.30" H - Aluminum 10024734
Accessories
The Warrior Line Interface card is manufactured by Scientific Data Systems (SDS) and allows the
Spartek Production Logging Tool to be run using the SDS logging panel instead of the Spartek
Systems SRO Panel. This interface card is pre-installed in most SDS/Warrior panels built in 2005 or
later. This interface card can be purchased from Spartek systems or directly from SDS.
• Compatible with the SDS SRO panel and the Warrior software application
• Installs inside the SDS SRO panel
• Provides a bi-directional communications interface between the SDS/Warrior SRO panel and the
Spartek Telemetry Logging tool string
Wireline Simulator
Item Description Item Number
Wireline Simulator Module - 15K ft - 3/16" line Type 10004640
Accessories
The PLT Breakout Test Box connects between Spartek 1.375" Specifications
PL Telemetry (or Memory) tool and any Spartek 1.375"D PLT Width 3.0"
Sonde thereby allowing the voltage and current drawn by the Length 11.0"
tools Sonde to be monitored. The PLT Breakout Test Box also Height 2.5"
allows for easy access to the power and RS485 bus Weight 0.87 lbs
communication lines for troubleshooting. Operating Temperature -25 – 55 C
• External replaceable fuse Operating Voltage 5 – 20 V DC
Operating Current 1 - 999 mA
• Red and blue LED display of Volts and Amps
Voltage Resolution 0.1 V
• Rugged aluminum enclosure
Amperage Resolution 1 mA
• Access to probe tool-bus power and communication lines
• Compatible with all 1.375"D Spartek PLT Sondes
• Ideal for individual tool Sonde checkout and bench
testing
Accessories
23
Standalone Analog Tools
Accessories
Item Description Item Number
Kit - ML1 - PL GO Field Joint - 1.375D / 1.688D - Aflas 90D - Med Sour 10023088
Kit - ML1 - PL GO Field Joint - 1.375D / 1.688D - Chemraz 90D - Sour 10023087
Kit - ML1 - PL GO Field Joint - 1.375D / 1.688D - Viton 90D - Sweet 10027168
1
Between 25° C and 177° C.
www.sparteksystems.com 1 Sep 2023 Well Integrity Catalog
24
Standalone Analog Tools
Accessories
Item Description Item Number
Case - Transport - 1.688D - 2 x 90.0" Slot 10029170
Kit - ML1 - PL GO Field Joint - 1.375D / 1.688D - Aflas 90D - Med Sour 10023088
Kit - ML1 - PL GO Field Joint - 1.375D / 1.688D - Chemraz 90D - Sour 10023087
Kit - ML1 - PL GO Field Joint - 1.375D / 1.688D - Viton 90D - Sweet 10027168
1
Between 25° C and 177° C.
www.sparteksystems.com 1 Sep 2023 Well Integrity Catalog
25
Standalone Analog Tools
Accessories
Item Description Item Number
Kit - ML1 - PL - Field Joint - 1.375D Aflas 90D / PEEK - Sour 10018336
Kit - ML1 - PL - Field Joint - 1.375D - Chemraz 90D / PEEK - Sour 10015753
Kit - ML1 - PL - Field Joint - 1.375D - Viton 90D / PEEK - Sweet 10015752
Kit - ML1 - SS8716 - E-Line Centralizer 177C - 1.688D - Aflas 90D 10030050
Kit - ML1 - SS8716 - E-Line Centralizer 177C - 1.688D - Chemraz 90D 10030049
Kit - ML2 - SS8716 - E-Line Centralizer - 177C - 1.688D - Aflas 90D / PEEK 10030047
Kit - ML2 - SS8716 - E-Line Centralizer - 177C - 1.688D - Chemraz 90D / PEEK - Sour 10030048
PL - Manual - ML1+ML2 SS8716 SA/D PL E-Line Centralizer 10028937
1
Maximum values include a 20% safety factor. Minimum values include a 50% safety factor (recommended).
www.sparteksystems.com 1 Sep 2023 Well Integrity Catalog
26
Casing Inspection Tools (CIT)
27
Casing Inspection Tools (CIT)
Accessories
Item Description Item Number
BNC-BNC Patch Cable - 50C - 1.2 m (4 ft) 10004571
1
Vertical sampling at 120 feet per minute.
www.sparteksystems.com 1 Sep 2023 Well Integrity Catalog
28
Casing Inspection Tools (CIT)
2 1 SS8130 SC - CIT Memory Assembly - 3.75D to 1.688D - 150C - 15000 PSI - Sour 10029025
2 1 SS8130 SC - CIT Memory Assembly - 3.75D to 1.688D - 150C - 15000 PSI - Sour 10029025
2 1 SS8130 SC - CIT Memory Assembly - 3.75D to 1.688D - 150C - 15000 PSI - Sour 10029025
2 1 SS8130 SC - CIT Memory Assembly - 3.75D to 1.688D - 150C - 15000 PSI - Sour 10029025
2 1 SS8130 SC - CIT Memory Assembly - 3.75D to 1.688D - 150C - 15000 PSI - Sour 10029025
Accessories
Item Description Item Number
Kit - ML2 - PL SRO Telemetry 1.375D / 1.688D - Chemraz 90D / Peek - Sour 10024620
1
Between 25 C and 177 C.
2
Single axis in-line with tool body.
www.sparteksystems.com 1 Sep 2023 Well Integrity Catalog
34
Casing Inspection Tools (CIT)
The Cablehead Tension tool provides feedback to let the user Specifications
know how much tension is being pulled at the cable head, Outer Diameter 1.688"
aiding in accidental pullout prevention and also allowing the Weight 10.1 lbs
user to know how much tension can actually be pulled in Pressure Rating 15 K psi
deep wells without damaging a tool string. Temperature Rating 177 C
Material Inconel 718
• Compatible with the Spartek SRO Logging Systems
Operating Voltage 7 – 17 V DC
• Electronic identification of serial-number and tool type
1 24.2 mA
• Measures tension and compression force Operating Current
• Internal temperature sensor for force compensation. Tension / Compression
Sensor Type Strain
Resolution +/-2.0 lbf
Accuracy 200 lbf
Range -20K to 20K lbf
Accessories
Item Description Item Number
Kit - ML1 - PL - 1.688D - Aflas 90D/ PEEK 10028081
Kit - ML1 - PL - 1.688D - Chemraz 90D/ PEEK - Sour 10027025
Kit - ML1 - PL - 1.688D - Viton 90D / PEEK 10028082
1
Between 25° C and 177° C.
www.sparteksystems.com 1 Sep 2023 Well Integrity Catalog
35
Casing Inspection Tools (CIT)
Accessories
Item Description Item Number
Kit - ML1 - PL - 1.688D - Aflas 90D/ PEEK 10028081
1
Between 25 C and 177 C.
www.sparteksystems.com 1 Sep 2023 Well Integrity Catalog
36
Casing Inspection Tools (CIT)
Accessories
Item Description Item Number
Cable - USB - 2 Meters - A/B 10016251
1
Between 25 C and 177 C.
www.sparteksystems.com 1 Sep 2023 Well Integrity Catalog
37
Casing Inspection Tools (CIT)
The Magnetic Flux Leakage (MFL) tool section of the Casing Specifications
Inspection Tool (CIT) is the key element of the tool string, Outer Diameter 3.75” collapsed
responsible for magnetizing the casing/pipe and then 4.30” open
detecting, identifying and quantifying flaws and defects in Weight 103.0 lbs
the casing. The MFL tool is available in several different Pressure Rating 15 K psi
diameters designed to suit the different casing and pipe Temperature Rating 150° C
diameters. Material Inconel 718
• Permanent Rare Earth Magnets Operating Voltage 7 V DC
• Magnetic Field Strength Sensors Operating Current1 950 mA
Sample Rate2 10 per inch
• Identifies both internal and external corrosion
Pad Count 8
• 4 GB Memory
Pad Sensor
• High Sampling Speed (not limited by wireline telemetry
systems) MFL Sensors 8
• Insensitive to logging speed Eddy Current Sensors 2
• Full radial coverage via 64 MFL sensors and 16 EC sensor Int. Temperature Sensor 1
Casing Penetration Range 20 – 100%
• 8 internal pad temperature sensors
Penetration Sensitivity 0.25” @ 20%
• Comes with thread protectors
Accuracy3 ± 15%
Repeatability ± 10%
Measurement Types
Metal Loss MFL
Int. vs Ext. Corrosion Flux Coupling
Accessories
Item Description Item Number
CIT - Manual - ML1+ML2 SS9000 MFL375 10032143
Kit - ML1 - SS90X0 - MFL - All Sizes - Field Joint - Viton 90D 10024214
1
Between 25 C and 177 C.
2
Vertical sampling at 120 feet per minute.
3
Isolated pit detection.
www.sparteksystems.com 1 Sep 2023 Well Integrity Catalog
38
Casing Inspection Tools (CIT)
The Magnetic Flux Leakage (MFL) tool section of the Casing Specifications
Inspection Tool (CIT) is the key element of the tool string, Outer Diameter 4.50” collapsed
responsible for magnetizing the casing/pipe and then 5.10” open
detecting, identifying and quantifying flaws and defects in Weight 133.0 lbs
the casing. The MFL tool is available in several different Pressure Rating 15 K psi
diameters designed to suit the different casing and pipe Temperature Rating 150° C
diameters. Material Inconel 718
• Permanent Rare Earth Magnets Operating Voltage 7 V DC
• Magnetic Field Strength Sensors Operating Current1 1025 mA
Sample Rate2 10 per inch
• Identifies both internal and external corrosion
Pad Count 10
• 4 GB Memory
Pad Sensor
• High Sampling Speed (not limited by wireline telemetry
systems) MFL Sensors 10
• Insensitive to logging speed Eddy Current Sensors 2
• Full radial coverage via 80 MFL sensors and 20 EC sensor Int. Temperature Sensor 1
Casing Penetration Range 20 – 100%
• 10 internal pad temperature sensors
Penetration Sensitivity 0.25” @ 20%
• Comes with thread protectors
Accuracy3 ± 15%
Repeatability ± 10%
Measurement Types
Metal Loss MFL
Int. vs Ext. Corrosion Flux Coupling
Accessories
Item Description Item Number
CIT - Manual - ML1+ML2 SS9020 MFL 450 10032144
Kit - ML1 - SS90X0 - MFL - All Sizes - Field Joint - Viton 90D 10024214
SS9020 - MFL450 - Casing Extension Kit for 6.625D Casing (5.790" to 5.921") 10032038
1
Between 25 C and 177 C.
2
Vertical sampling at 120 feet per minute.
3
Isolated pit detection.
www.sparteksystems.com 1 Sep 2023 Well Integrity Catalog
39
Casing Inspection Tools (CIT)
The Magnetic Flux Leakage (MFL) tool section of the Casing Specifications
Inspection Tool (CIT) is the key element of the tool string, Outer Diameter 5.75” collapsed
responsible for magnetizing the casing/pipe and then 6.60” open
detecting, identifying and quantifying flaws and defects in Weight 193.0 lbs
the casing. The MFL tool is available in several different Pressure Rating 15 K psi
diameters designed to suit the different casing and pipe Temperature Rating 150° C
diameters. Material Inconel 718
• Permanent Rare Earth Magnets Operating Voltage 7 V DC
• Magnetic Field Strength Sensors Operating Current1 1100 mA
Sample Rate2 10 per inch
• Identifies both internal and external corrosion
Pad Count 12
• 4 GB Memory
Pad Sensor
• High Sampling Speed (not limited by wireline telemetry
systems) MFL Sensors 12
• Insensitive to logging speed Eddy Current Sensors 2
• Full radial coverage via 96 MFL sensors and 24 EC sensor Int. Temperature Sensor 1
Casing Penetration Range 20 – 100%
• 12 internal pad temperature sensors
Penetration Sensitivity 0.25” @ 20%
• Comes with thread protectors
Accuracy3 ± 15%
Repeatability ± 10%
Measurement Types
Metal Loss MFL
Int. vs Ext. Corrosion Flux Coupling
Accessories
Item Description Item Number
CIT - Centralizer - Bullnose - 3 1/8" - 12 UNF - 3.75"D - set screw 10024991
Kit - ML1 - SS90X0 - MFL - All Sizes - Field Joint - Viton 90D 10024214
SS9030 - MFL575 - Casing Extension Kit for 8.625D Casing (7.725" - 7.921") 10032070
1
Between 25 C and 177 C.
2
Vertical sampling at 120 feet per minute.
3
Isolated pit detection.
www.sparteksystems.com 1 Sep 2023 Well Integrity Catalog
40
Casing Inspection Tools (CIT)
The Magnetic Flux Leakage (MFL) tool section of the Casing Specifications
Inspection Tool (CIT) is the key element of the tool string, Outer Diameter 8.00” collapsed
responsible for magnetizing the casing/pipe and then 12.75” open
detecting, identifying and quantifying flaws and defects in Weight 353.0 lbs
the casing. The MFL tool is available in several different Pressure Rating 15 K psi
diameters designed to suit the different casing and pipe Temperature Rating 150° C
diameters. Material Inconel 718
• Permanent Rare Earth Magnets Operating Voltage 7 V DC
• Magnetic Field Strength Sensors Operating Current1 1250 mA
Sample Rate2 10 per inch
• Identifies both internal and external corrosion
Pad Count 16
• 4 GB Memory
Pad Sensor
• High Sampling Speed (not limited by wireline telemetry
systems) MFL Sensors 16
• Insensitive to logging speed Eddy Current Sensors 2
• Full radial coverage via 128 MFL sensors and 32 EC sensor Int. Temperature Sensor 1
Casing Penetration Range 20 – 100%
• 16 internal pad temperature sensors
Penetration Sensitivity 0.25” @ 20%
• Comes with thread protectors
Accuracy3 ± 15%
Measurement Types
Metal Loss MFL
Int. vs Ext. Corrosion Flux Coupling
Accessories
Item Description Item Number
CIT - Manual - ML1+ML2 SS9040 MFL800 10032146
Kit - ML1 - SS90X0 - MFL - All Sizes - Field Joint - Viton 90D 10024214
1
Between 25 C and 177 C.
2
Vertical sampling at 120 feet per minute.
3
Isolated pit detection.
www.sparteksystems.com 1 Sep 2023 Well Integrity Catalog
41
Casing Inspection Tools (CIT)
The MFL bottom adapter is placed in the CIT tool string Specifications
below the MFL section. The adapter supports the lower slip Outer Diameter 3.75”"
over centralizer. Weight 23.5 lbs
• Electrical feed thru allows other Spartek logging tools to Pressure Rating 15 K psi
be attached below the CIT tool string. Check with Spartek Temperature Rating 150 C
Sales personnel to determine tool string compatibility. Material Inconel 718
Operating Voltage N/A
Operating Current N/A
Accessories
Item Description Item Number
CIT - Manual - ML1+ML2 Bottom Adapter - 3.75D to 1.66D 10032261
CIT - Replacement - Bottom Adapter Slip Over Thread Protector - 3.75"D 10029086
Accessories
Item Description Item Number
CIT - 3.75" - Level Centralizer Bullnose with 1.702 ID 10029732
1
See the Maintenance Level 1 document for assembly and disassembly instructions.
www.sparteksystems.com 1 Sep 2023 Well Integrity Catalog
43
Casing Inspection Tools (CIT)
Accessories
Item Description Item Number
CIT - Manual - ML1+ML2 SS8731 SA High Deviation Centralizer 10032128
CIT - Replacement - SS8732 Centralizer - Maximum Open Limit Ring - 0.165W 10029222
CIT - Replacement - SS8732 Centralizer - Maximum Open Limit Ring - 1.86 W 10029214
Accessories
Accessories
SS9030 - MFL575 - Casing Extension Kit for 8.625D Casing (7.725" - 7.921") 10032070
Extends the pads of the MFL 450 and 575 tools to measure MFL 450 MFL575
larger casing sizes Tool Body OD 4.50” 5.75”
Kit OD 5.50” 7.40”
• Kit bolts on to tool – No modifications are required to
Measurement 5.790” to 7.725” to
MFL sections
Range 5.921” 7.921”
• No need to change or remove electrical connections
• Original pads on the tool remain the same
Accessories
Elastomer % H2S Tolerated
Service Temperature
Material
Cost Type Range < 150 C > 150 C
Viton $ Sweet < 150 C < 5% Not Rated
Aflas $$ Medium-Sour 5 – 218 C < 20% < 7%
Chemraz $$$ Sour -20 – 250 C > 20% > 7%
Kalrez $$$ Sour -26 – 325 C > 20% > 7%
Celazole - -- -20 - 350 C > 20% > 7%
PEEK -- -- -20 – 200 C > 20% > 7%
EPDM $$ Steam -< 10% -60 – 315 C < 7% < 7%
Petroleum
Consumables
The following consumables are used for assembly and field maintenance of the CIT tool strings.
Accessories
Thread Protectors
Item Description Item Number
CIT - Replacement - Thread Protector - 1.875 -12 UN - Bottom Adapter - 3.75"D 10023977
CIT - Replacement - Thread Protector - 3.25-12 SA - Memory/Pad Section Bottom - 3.75"D 10023965
CIT - Replacement - Thread Protector - 3.25-12 SA - Pad Section Top - 3.75"D 10023966
The thread protectors are used to protect the "GO" tool box
and pin threads of each individual sonde in the Production
Logging Tool.
Accessories
This page is intentionally blank.
49
Multi-Finger Calipers (MFC)
PL - 1.688" - Battery Housing - 4 x "DD" - 0.938" 10 UN Pin - Sucker Rod - Sour 10026037
2 SS8122 SB - HYBRID - SRO/MEM - Controller - 177C - 15000 psi - 1.688D - Sour 10031425
4 SS8720 SB - PL In-Line Roller Centralizer - 177C - 15000 psi - 1.688D - Sour 10028767
5 SS9102 SA - Multi Finger Caliper - 24 Finger - 175C - 15000 psi - 1.688 OD - Extended Finger 10026758
6 SS8720 SB - PL In-Line Roller Centralizer - 177C - 15000 psi - 1.688D - Sour 10028767
PL - 1.688" - Battery Housing - 4 x "DD" - 0.938" 10 UN Pin - Sucker Rod - Sour 10026037
2 SS8122 SB - HYBRID - SRO/MEM - Controller - 177C - 15000 psi - 1.688D - Sour 10031425
4 SS8720 SB - PL In-Line Roller Centralizer - 177C - 15000 psi - 1.688D - Sour 10028767
5 SS8950 SA - Signal Adapter Module - 177C - 15000 psi - 1.688D - Sour 10031203
6 SS9104 SA - Multi Finger Caliper - 24 Finger - 175C - 15000 psi - 1.69 OD - Sour 10031039
* A SS8716SA E-line centralizer can be placed between the SS8950 SA SAM and the SS9104 SA MFC.
PL - 1.688" - Battery Housing - 4 x "DD" - 0.938" 10 UN Pin - Sucker Rod - Sour 10026037
2 SS8122 SB - HYBRID - SRO/MEM - Controller - 177C - 15000 psi - 1.688D - Sour 10031425
4 SS9205 SA - In-Line Centralizer - 5 Arm Roller - 177C - 15000 psi - 2.75D - Sour 10026090
5 SS9101 SA - Multi Finger Caliper - 40 Finger - 175C - 15000 psi - 2.88D 10026357
6 SS9205 SA - In-Line Centralizer - 5 Arm Roller - 177C - 15000 psi - 2.75D - Sour 10026090
The SS8150 is a Hybrid SRO Controller that supports our new Specifications
data framing structure for surface communications. It is Outer Diameter 1.688”
capable of supporting array type data sensors and variable Weight 15.78 lbs
sample rates. Makeup Length 46.21”
Pressure Rating 15 K psi
Features Temperature Rating 177 C
• Power: Wireline or Battery Pack Material Inconel 718
• Modes: SRO (Warrior), Memory (SparWorks) & Hybrid Operating Voltage 175 V DC
(Mixed) (nominal)
• Sampling: Varying Sample Rates & Complex Array Data Operating Current 25 mA
Voltage Range 120 – 240 V DC
SS8150 Modem SS8150 Modem
• 50 K bits / sec Uplink Downlink 5 K bps
• Enhanced Power Supply Uplink 50 K bps
• Control - Bi-Directional Uplink & Down Link Weight 9.60 lbs
• Standard 1-3/16”-12 GO box connection at top Makeup Length 27.10”
SS8122 Controller
SS8122 Hybrid SRO/Memory Controller Tool Bus 115 K / 460.8 K bps
• 1 GB Memory Memory 1 G bytes
• High Speed USB Dump Channel Weight 9.60 lbs
• Tool Bus Power Management (enhanced DBAM) Makeup Length 19.11”
• Audible Indicator for Power Activation (memory) Cablehead Voltage Range 0 – 240 V
• Cablehead (or Battery) Voltage & Current Accelerometer (ACC)
• Incorporates a three-axis accelerometer for measuring Range ±5 g
tool movement and inclination. Resolution 0.01g
• Automatic connected tool sonde detection
Accessories
Item Description Item Number
Kit - ML1 - SS8122 SB - Memory - 1.688D - Aflas 83D / PEEK 10031846
Kit - ML1 - SS8122 SB - Memory - 1.688D - Kalrez 90D / PEEK - Sour 10031847
Kit - ML1 - SS8122 SB - Memory - 1.688D - Viton 90D / PEEK - Sweet 10031845
Kit - ML2 - SS8122 SB - Memory - 1.688D - Kalrez 90D / PEEK - Sour 10031848
SRO/Telemetry Tool Power Adapter - 1.375 OD 10005851
1
All three items need to be ordered to make up a tool.
www.sparteksystems.com 1 Sep 2023 Well Integrity Catalog
53
Multi-Finger Calipers (MFC)
The Cablehead Tension tool provides feedback to let the user Specifications
know how much tension is being pulled at the cable head, Outer Diameter 1.688"
aiding in accidental pullout prevention and also allowing the Weight 10.1 lbs
user to know how much tension can actually be pulled in Pressure Rating 15 K psi
deep wells without damaging a tool string. Temperature Rating 177 C
Material Inconel 718
• Compatible with the Spartek SRO Logging Systems
Operating Voltage 7 – 17 V DC
• Electronic identification of serial-number and tool type
1 24.2 mA
• Measures tension and compression force Operating Current
• Internal temperature sensor for force compensation. Tension / Compression
Sensor Type Strain
Resolution +/-2.0 lbf
Accuracy 200 lbf
Range -20K to 20K lbf
Accessories
Item Description Item Number
Kit - ML1 - PL - 1.688D - Aflas 90D/ PEEK 10028081
Kit - ML1 - PL - 1.688D - Chemraz 90D/ PEEK - Sour 10027025
Kit - ML1 - PL - 1.688D - Viton 90D / PEEK 10028082
1
Between 25° C and 177° C.
www.sparteksystems.com 1 Sep 2023 Well Integrity Catalog
54
Multi-Finger Calipers (MFC)
Accessories
Item Description Item Number
Kit - ML1 - PL - 1.688D - Aflas 90D/ PEEK 10028081
Kit - ML1 - PL - 1.688D - Chemraz 90D/ PEEK - Sour 10027025
Kit - ML1 - PL - 1.688D - Viton 90D / PEEK 10028082
Kit - ML2 - SS8211 SA - GR/CCL - 1.688D - Chemraz 90D/ PEEK - Sour 10027684
PL - Gamma Ray Calibration Fixture 10013605
PL - Manual - ML1+ML2 SS8211 SA 1.688D Gamma CCL 10027598
1
Between 25 C and 177 C.
www.sparteksystems.com 1 Sep 2023 Well Integrity Catalog
55
Multi-Finger Calipers (MFC)
Accessories
Item Description Item Number
Grease - Metalon High-Tech EP 1.5 - 400 gm Tube 10027207
Grease Fitting with Ball Check - .25"-28 Straight Steel Zinc 10027338
Grease Gun - HD Lincoln 10028607
Kit - ML1 - PL - 1.688D - Aflas 90D/ PEEK 10028081
Kit - ML1 - PL - 1.688D - Chemraz 90D/ PEEK - Sour 10027025
Kit - ML1 - PL - 1.688D - Viton 90D / PEEK 10028082
Accessories
Item Description Item Number
Kit - ML1 - PL - 1.688D - Aflas 90D/ PEEK 10028081
Kit - ML2 - SS8720 SA - In-Line Centralizer - 1.688D - Chemraz 90D/ PEEK - Sour 10028094
1
Between 25 C and 177 C.
www.sparteksystems.com 1 Sep 2023 Well Integrity Catalog
57
Multi-Finger Calipers (MFC)
Accessories
Item Description Item Number
Field Service Kit - 5 Arm Roller Centralizers - RAC-20 10024223
Accessories
Item Description Item Number
Case - Transport - MFC - 1.688D - 24 Finger 10027306
Accessories
Item Description Item Number
Case - Transport - MFC - 2.88D - 40 Finger 10027173
MFC - Multi Finger Caliper - 40 Finger - Cal Bowl - 10" - Ext Finger 10033763
1
Connection to 1.375” PLT’s requires crossover 10026038 or 10026039
www.sparteksystems.com 1 Sep 2023 Well Integrity Catalog
60
Multi-Finger Calipers (MFC)
Accessories
Item Description Item Number
Case - Transport - MFC - 4.0D - 60 Finger 10027307
1
Between 25 C and 177 C.
2
Single axis in-line with tool body.
www.sparteksystems.com 1 Sep 2023 Well Integrity Catalog
61
Multi-Finger Calipers (MFC)
Accessories
Item Description Item Number
Kit - ML1 - PL - 1.688D - Aflas 90D/ PEEK 10028081
Kit - ML1 - PL - Field Joint - 1.375D Aflas 90D / PEEK - Sour 10018336
Kit - ML1 - PL - Field Joint - 1.375D - Chemraz 90D / PEEK - Sour 10015753
Kit - ML1 - PL - Field Joint - 1.375D - Viton 90D / PEEK - Sweet 10015752
Accessories
Item Description Item Number
Kit - ML1 - PL - Field Joint - 1.375D Aflas 90D / PEEK - Sour 10018336
Kit - ML1 - PL - Field Joint - 1.375D - Chemraz 90D / PEEK - Sour 10015753
Kit - ML1 - PL - Field Joint - 1.375D - Viton 90D / PEEK - Sweet 10015752
SS8950 SA - Signal Adapter Module - 177C - 15000 psi - 1.688D - Sour 10031203
Accessories
Accessories
PL - 1.688" - Battery Housing - 4 x "D" - 0.938" 10 UN Pin - Sucker Rod - Sour 17.62” 10026036
PL - 1.688" - Battery Housing - 4 x "DD" - 0.938" 10 UN Pin - Sucker Rod - Sour 28.12” 10026037
Battery housing options for use with the Memory Production Specifications
Logging Tool (MPLT) or the Compact Memory Production Outer Diameter 1.688”
Logging Tool (CPLT). Pressure Rating 15 K psi
Temperature Rating 177 °C
Material Inconel 718
Pin Thread 0.938”-10 UN Pin
Sucker Rod
Tensile Strength 64 K lbs
Battery Packs
Item Description Item Number
PL - Battery Pack - 4 x "D" - 10.0 Ah - 14.6V - 165C - Non-Locking - 11 Pin 10026042
PL - Battery Pack - 4 x "DD" - 18.0Ah - 14.6V - 165C - Non Locking - 11 Pin 10026043
Lithium Battery Packs for use with the Memory Production Capacity (Ah)1 Run Time (hours)2
Logging Tool (MPLT) 10.0 50
18.0 90
• Locking 11-pin connector
• Unique serial number on each pack
1
Battery pack capacity values (Amp hours) are based on worst case conditions.
2
Estimated run time is based on a typical PLT tool string configuration drawing approximately 200 mA.
-Typical PLT string: MEM + CENT + GR/CCL + TP + CAP + ADT + ILS + CENT + FBS
www.sparteksystems.com 1 Sep 2023 Well Integrity Catalog
64
Multi-Finger Calipers (MFC)
Accessories
Calibrators
Item Description Item Number
Case - Transport - MFC - Calibration Bowl 10031871
MFC - Multi Finger Caliper - 40 Finger - Cal Bowl - 10" - Ext Finger 10033763
MFC - Multi Finger Caliper - 40 Finger - Cal Bowl - 7.5" Standard Finger 10029729
Accessories
Accessories
Item Description Item Number
Kit - ML1 - PL - Crossover 1.688D to 1.375D - Chemraz 90D / PEEK - Sour 10028598
Bullnose / Crossover
Item Description ML Item Number
Bullnose - 1.375" OD - 0.938" 10 UN Pin - 316 SS 3.50” 10028507
Bullnose - 1.375D - GO Box - 15000 psi - Sour 4.00” 10027570
Crossover - PL - 1.688" PL Pin to 5/8" Sucker Rod-Box - Sour 2.38” 10028453
PL - Bullnose - 1.688D Tool String - 15000 psi - Sour 2.62” 10025247
The Bullnose provides a pressure seal for the bottom of the Specifications
tool. Outer Diameter 1.688"
Pressure Rating 20 K psi
• Compatible with all Spartek 1.688" PL tools Temperature Rating 300 C
Material Inconel 718
Accessories
Item Description Item Number
Kit - Redress - PL - HTHP - 1.688D Field Joint - Kalrez - Sour 10028540
Accessories
Miscellaneous Tools
Item Description Item Number
O-Ring Removal Tool - Plastic 10010354
Wrench - Open End - 1.50" - 0.34 Wide 10028573
Wrench - Thin Pattern Pump - 1-1/2" 10016665
Accessories
Shipping Case
Item Description Item Number
Case - Transport - PL - 1.688D - 4 x 48.5" Slot 10026789
The thread protectors are used to protect those tools that Specifications
have a GO tool box or pin threads. Outer Diameter 1.88"
Length 2.50”
• Compatible with 1.688" OD GO tools
Weight 0.25 lbs
• Protects threads and O-rings during transportation
Material PVC
• Prevents moisture entering tool connectors while
washing tools
Accessories
The thread protectors are used to protect the tool box and Specifications
pin threads of each individual sonde in the Production Outer Diameter 1.88"
Logging Tool. Length 1.50" / 1.10”
Weight 0.35 lbs
• Compatible with all Spartek or 1.688" OD PL Tools
Material PVC
• Protects threads and O-rings during transportation
• Prevents moisture entering tool connectors while
washing tools
Accessories
This page is intentionally blank.
71
Cement Bond Logging Tools (SCBT) – SRO
• 1.688” inline centralizer is recommended for all jobs (no matter the casing size or deviation)
• 2.75” Inline centralizer is recommended for wells exceeding 30° or casings 7” or larger
• 3.50” Inline centralizer is recommended for wells exceeding 30° or 9-5/8” casings or larger
1.688”
# Item Description Item Number
1 SS9248 SA - Roller Centralizer - E-Line - 204C - 20000 psi - 1.68D 10025192
2 SS9212 SA - SCBT - (CCL/GR/TEMP/6x Radial/3' Near/5' Far) - 204C - 25000 psi - 1.68D 10025237
3 1
SS9249 SA - Mid Roller Centralizer - Inline (19 Pin) - 204C - 20000 psi - 1.68D 10025973
2.75”
# Item Description Item Number
1 SS9228 SA - Roller Centralizer - E-Line - 204C - 20000 psi - 2.75D 10023064
2 SS9220 SA - SCBT - (CCL/GR/TEMP/8x Radial/3' Near/5' Far) - 204C - 25000 psi - 2.75D 10023066
337
SS9229 SA - Mid Roller Centralizer - Inline (19 pin) - 204C - 20000 psi - 2.75D 10023067
3.50”
# Item Description Item Number
1 SS9238 SA - Roller Centralizer - E-Line - 204C - 20000 psi - 3.50D 10023070
2 SS9230 SA - SCBT - (CCL/GR/TEMP/12x Radial/3' Near/5' Far) - 204C - 25000 psi - 3.50D 10026743
337 SS9239 SA - Mid Roller Centralizer - Inline (19 pin) - 204C - 20000 psi - 3.50D 10023071
1
Centralizer is placed between electronics and sonde in SCBT
www.sparteksystems.com 1 Sep 2023 Well Integrity Catalog
72
Cement Bond Logging Tools (SCBT) – SRO
Accessories
Item Description Item Number
Bullnose - 1.375D - GO Box - 15000 psi - Sour 10027570
Redress Kit - SS9240 - Go End Assembly and Filling Port Assembly 10029298
Accessories
Item Description Item Number
Redress Kit - SS9212 SA - Field Service Kit 10025885
Redress Kit - SS9248 & SS9249 - Arms and Related Pins 10029307
Redress Kit - SS9248 & SS9249 - Wheels and Related Pins 10029301
SCBT - Manual - SS9248 & SS9249 - Centralizer Service and Operation Manual - 1.688" 10027259
Accessories
Item Description Item Number
Redress Kit - SS9248 & SS9249 - Arms and Related Pins 10029307
Redress Kit - SS9248 & SS9249 - Wheels and Related Pins 10029301
SCBT - Manual - SS9248 & SS9249 - Centralizer Service and Operation Manual - 1.688" 10027259
Accessories
Item Description Item Number
Bullnose - 1.375D - GO Box - 15000 psi - Sour 10027570
Redress Kit - SS9220 - Go End Assembly and Filling Port Assembly 10029299
Accessories
Item Description Item Number
Redress Kit - SS9228 - Exposed O-Rings 10029282
Redress Kit - SS9228 & SS9229 - Arms and Related Pins 10029308
Redress Kit - SS9228 & SS9229 - Wheels and Related Pins 10029302
SCBT - Manual - SS9228/9 & SS9205 - Centralizer Service and Operation Manual - 2.75" 10027260
Accessories
Item Description Item Number
Redress Kit - SS9228 & SS9229 - Arms and Related Pins 10029308
Redress Kit - SS9228 & SS9229 - Wheels and Related Pins 10029302
SCBT - Manual - SS9228/9 & SS9205 - Centralizer Service and Operation Manual - 2.75" 10027260
Accessories
Item Description Item Number
Bullnose - 1.375D - GO Box - 15000 psi - Sour 10027570
Field Service Kit - High Speed Radial Bond Tool - HSR-35 10025123
Redress Kit - SS9230 - Go End Assembly and Filling Port Assembly 10029300
Accessories
Item Description Item Number
Case - Transport - Bond Tool Centralizer - 3.5" OD X 1 10026558
Redress Kit - SS9238 & SS9239 - Arms and Related Pins 10029309
Redress Kit - SS9238 & SS9239 - Wheels and Related Pins 10029303
Accessories
Item Description Item Number
Case - Transport - Bond Tool Centralizer - 3.5" OD X 1 10026558
Redress Kit - SS9238 & SS9239 - Arms and Related Pins 10029309
Redress Kit - SS9238 & SS9239 - Wheels and Related Pins 10029303
83
Cement Bond Logging Tools (SCBT) - Memory
PL - 1.688" - Battery Housing - 4 x "DD" - 0.938" 10 UN Pin - Sucker Rod - Sour 10026037
2 SS8122 SB - HYBRID - SRO/MEM - Controller - 177C - 15000 psi - 1.688D - Sour 10031425
4 SS8720 SB - PL In-Line Roller Centralizer - 177C - 15000 psi - 1.688D - Sour 10028767
61 SS9249 SA - Mid Roller Centralizer - Inline (19 Pin) - 204C - 20000 psi - 1.68D 10025973
7 SS8720 SB - PL In-Line Roller Centralizer - 177C - 15000 psi - 1.688D - Sour 10028767
1
Centralizer is placed between electronics and sonde in SCBT
www.sparteksystems.com 1 Sep 2023 Well Integrity Catalog
84
Cement Bond Logging Tools (SCBT) - Memory
2.75” Configuration
# Item Description Item Number
1 PL - 1.688" - Battery Housing - 4 x "D" - 0.938" 10 UN Pin - Sucker Rod - Sour 10026036
PL - 1.688" - Battery Housing - 4 x "DD" - 0.938" 10 UN Pin - Sucker Rod - Sour 10026037
2 SS8122 SB - HYBRID - SRO/MEM - Controller - 177C - 15000 psi - 1.688D - Sour 10031425
4 SS9205 SA - In-Line Centralizer - 5 Arm Roller - 177C - 15000 psi - 2.75D - Sour 10026090
6 SS9229 SA - Mid Roller Centralizer - Inline (19 pin) - 204C - 20000 psi - 2.75D 10023067
7 SS9205 SA - In-Line Centralizer - 5 Arm Roller - 177C - 15000 psi - 2.75D - Sour 10026090
The SS8150 is a Hybrid SRO Controller that supports our new Specifications
data framing structure for surface communications. It is Outer Diameter 1.688”
capable of supporting array type data sensors and variable Weight 15.78 lbs
sample rates. Makeup Length 46.21”
Pressure Rating 15 K psi
Features Temperature Rating 177 C
• Power: Wireline or Battery Pack Material Inconel 718
• Modes: SRO (Warrior), Memory (SparWorks) & Hybrid Operating Voltage 175 V DC
(Mixed) (nominal)
• Sampling: Varying Sample Rates & Complex Array Data Operating Current 25 mA
Voltage Range 120 – 240 V DC
SS8150 Modem SS8150 Modem
• 50 K bits / sec Uplink Downlink 5 K bps
• Enhanced Power Supply Uplink 50 K bps
• Control - Bi-Directional Uplink & Down Link Weight 9.60 lbs
• Standard 1-3/16”-12 GO box connection at top Makeup Length 27.10”
SS8122 Controller
SS8122 Hybrid SRO/Memory Controller Tool Bus 115 K / 460.8 K bps
• 1 GB Memory Memory 1 G bytes
• High Speed USB Dump Channel Weight 9.60 lbs
• Tool Bus Power Management (enhanced DBAM) Makeup Length 19.11”
• Audible Indicator for Power Activation (memory) Cablehead Voltage Range 0 – 240 V
• Cablehead (or Battery) Voltage & Current Accelerometer (ACC)
• Incorporates a three-axis accelerometer for measuring Range ±5 g
tool movement and inclination. Resolution 0.01g
• Automatic connected tool sonde detection
Accessories
Item Description Item Number
Kit - ML1 - SS8122 SB - Memory - 1.688D - Aflas 83D / PEEK 10031846
Kit - ML1 - SS8122 SB - Memory - 1.688D - Kalrez 90D / PEEK - Sour 10031847
Kit - ML1 - SS8122 SB - Memory - 1.688D - Viton 90D / PEEK - Sweet 10031845
Kit - ML2 - SS8122 SB - Memory - 1.688D - Kalrez 90D / PEEK - Sour 10031848
SRO/Telemetry Tool Power Adapter - 1.375 OD 10005851
1
All three items need to be ordered to make up a tool.
www.sparteksystems.com 1 Sep 2023 Well Integrity Catalog
86
Cement Bond Logging Tools (SCBT) - Memory
The Cablehead Tension tool provides feedback to let the user Specifications
know how much tension is being pulled at the cable head, Outer Diameter 1.688"
aiding in accidental pullout prevention and also allowing the Weight 10.1 lbs
user to know how much tension can actually be pulled in Pressure Rating 15 K psi
deep wells without damaging a tool string. Temperature Rating 177 C
• Compatible with the Spartek SRO Logging Systems Material Inconel 718
Operating Voltage 7 – 17 V DC
• Electronic identification of serial-number and tool type
1 24.2 mA
• Measures tension and compression force Operating Current
• Internal temperature sensor for force compensation. Tension / Compression
Sensor Type Strain
Resolution +/-2.0 lbf
Accuracy 200 lbf
Range -20K to 20K lbf
Accessories
Item Description Item Number
Kit - ML1 - PL - 1.688D - Aflas 90D/ PEEK 10028081
Kit - ML1 - PL - 1.688D - Chemraz 90D/ PEEK - Sour 10027025
Kit - ML1 - PL - 1.688D - Viton 90D / PEEK 10028082
1
Between 25° C and 177° C.
www.sparteksystems.com 1 Sep 2023 Well Integrity Catalog
87
Cement Bond Logging Tools (SCBT) - Memory
Accessories
Item Description Item Number
Grease - Metalon High-Tech EP 1.5 - 400 gm Tube 10027207
Grease Fitting with Ball Check - .25"-28 Straight Steel Zinc 10027338
Grease Gun - HD Lincoln 10028607
Kit - ML1 - PL - 1.688D - Aflas 90D/ PEEK 10028081
Kit - ML1 - PL - 1.688D - Chemraz 90D/ PEEK - Sour 10027025
Kit - ML1 - PL - 1.688D - Viton 90D / PEEK 10028082
Accessories
Item Description Item Number
Kit - ML1 - PL - 1.688D - Aflas 90D/ PEEK 10028081
Kit - ML1 - PL - 1.688D - Chemraz 90D/ PEEK - Sour 10027025
Kit - ML1 - PL - 1.688D - Viton 90D / PEEK 10028082
Kit - ML2 - SS8211 SA - GR/CCL - 1.688D - Chemraz 90D/ PEEK - Sour 10027684
PL - Gamma Ray Calibration Fixture 10013605
PL - Manual - ML1+ML2 SS8211 SA 1.688D Gamma CCL 10027598
1
Between 25 C and 177 C.
www.sparteksystems.com 1 Sep 2023 Well Integrity Catalog
89
Cement Bond Logging Tools (SCBT) - Memory
Accessories
Item Description Item Number
Kit - ML1 - PL - 1.688D - Aflas 90D/ PEEK 10028081
Kit - ML2 - SS8720 SA - In-Line Centralizer - 1.688D - Chemraz 90D/ PEEK - Sour 10028094
1
Between 25 C and 177 C.
www.sparteksystems.com 1 Sep 2023 Well Integrity Catalog
90
Cement Bond Logging Tools (SCBT) - Memory
Accessories
Item Description Item Number
Kit - ML1 - PL - 1.688D - Aflas 90D/ PEEK 10028081
SCBT - Manual - ML1+ML2 SS9240 SA 1.688D Segmented Cement Bond Tool 10029385
SS8121 SA - Memory Controller - 177C - 15000 psi - 1.69D - Inconel -718 - Sour 10025938
SS8720 SB - PL In-Line Roller Centralizer - 177C - 15000 psi - 1.688D - Sour 10028767
SS9249 SA - Mid Roller Centralizer - Inline (19 Pin) - 204C - 20000 psi - 1.68D 10025973
Accessories
Item Description Item Number
Redress Kit - SS9248 & SS9249 - Arms and Related Pins 10029307
Redress Kit - SS9248 & SS9249 - Wheels and Related Pins 10029301
SCBT - Manual - SS9248 & SS9249 - Centralizer Service and Operation Manual - 1.688" 10027259
Accessories
Item Description Item Number
Doc - OP - SS9225 Segmented Cement Bond Tool (SCBT) 10028327
SCBT - Manual - ML1+ML2 SS9225 2.75D Segmented Cement Bond Tool 10027732
SS8121 SA - Memory Controller - 177C - 15000 psi - 1.69D - Inconel -718 - Sour 10025938
SS9205 SA - In-Line Centralizer - 5 Arm Roller - 177C - 15000 psi - 2.75D - Sour 10026090
SS9229 SA - Mid Roller Centralizer - Inline (19 pin) - 204C - 20000 psi - 2.75D 10023067
Accessories
Item Description Item Number
Field Service Kit - 5 Arm Roller Centralizers - RAC-20 10024223
Accessories
Item Description Item Number
Redress Kit - SS9228 & SS9229 - Arms and Related Pins 10029308
Redress Kit - SS9228 & SS9229 - Wheels and Related Pins 10029302
SCBT - Manual - SS9228/9 & SS9205 - Centralizer Service and Operation Manual - 2.75" 10027260
Accessories
Accessories
PL - 1.688" - Battery Housing - 4 x "D" - 0.938" 10 UN Pin - Sucker Rod - Sour 17.62” 10026036
PL - 1.688" - Battery Housing - 4 x "DD" - 0.938" 10 UN Pin - Sucker Rod - Sour 28.12” 10026037
Battery housing options for use with the Memory Production Specifications
Logging Tool (MPLT) or the Compact Memory Production Outer Diameter 1.688”
Logging Tool (CPLT). Pressure Rating 15 K psi
Temperature Rating 177 °C
Material Inconel 718
Pin Thread 0.938”-10 UN Pin
Sucker Rod
Tensile Strength 64 K lbs
Battery Packs
Item Description Item Number
PL - Battery Pack - 4 x "D" - 10.0 Ah - 14.6V - 165C - Non-Locking - 11 Pin 10026042
PL - Battery Pack - 4 x "DD" - 18.0Ah - 14.6V - 165C - Non Locking - 11 Pin 10026043
Lithium Battery Packs for use with the Memory Production Capacity (Ah)1 Run Time (hours)2
Logging Tool (MPLT) 10.0 50
18.0 90
• Locking 11-pin connector
• Unique serial number on each pack
1
Battery pack capacity values (Amp hours) are based on worst case conditions.
2
Estimated run time is based on a typical PLT tool string configuration drawing approximately 200 mA.
-Typical PLT string: MEM + CENT + GR/CCL + TP + CAP + ADT + ILS + CENT + FBS
www.sparteksystems.com 1 Sep 2023 Well Integrity Catalog
96
Cement Bond Logging Tools (SCBT) - Memory
Accessories
Accessories
Item Description Item Number
Kit - ML1 - PL - Crossover 1.688D to 1.375D - Chemraz 90D / PEEK - Sour 10028598
Bullnose / Crossover
Item Description ML Item Number
Bullnose - 1.375" OD - 0.938" 10 UN Pin - 316 SS 3.50” 10028507
Bullnose - 1.375D - GO Box - 15000 psi - Sour 4.00” 10027570
Crossover - PL - 1.688" PL Pin to 5/8" Sucker Rod-Box - Sour 2.38” 10028453
PL - Bullnose - 1.688D Tool String - 15000 psi - Sour 2.62” 10025247
The Bullnose provides a pressure seal for the bottom of the Specifications
tool. Outer Diameter 1.688"
Pressure Rating 20 K psi
• Compatible with all Spartek 1.688" PL tools Temperature Rating 300 C
Material Inconel 718
Accessories
Item Description Item Number
Kit - Redress - PL - HTHP - 1.688D Field Joint - Kalrez - Sour 10028540
Accessories
Miscellaneous Tools
Item Description Item Number
O-Ring Removal Tool - Plastic 10010354
Wrench - Open End - 1.50" - 0.34 Wide 10028573
Wrench - Thin Pattern Pump - 1-1/2" 10016665
Accessories
Shipping Case
Item Description Item Number
Case - Transport - PL - 1.688D - 4 x 48.5" Slot 10026789
The thread protectors are used to protect the tool box and Specifications
pin threads of each individual sonde in the Production Outer Diameter 1.88"
Logging Tool. Length 1.50" / 1.10”
Weight 0.35 lbs
• Compatible with all Spartek or 1.688" OD PL Tools
Material PVC
• Protects threads and O-rings during transportation
• Prevents moisture entering tool connectors while
washing tools
Accessories
This page is intentionally blank.
Accessories
Warranty
1–Year Limited Warranty
Spartek Systems warrants that all its Products are free of any known defects in materials and workmanship, have been calibrated, and tested to work as intended.
In the event the Product fails during twelve months from date of shipment, and said Product has not been abused as determined by Seller’s Agent, the defective
Product will be repaired (or replaced at Spartek Systems discretion) at no charge.
If abuse is determined to be the cause of failure, the Customer will be notified and repair charges will be applicable.
Product items that are expendable in normal use are not covered by this warranty (i.e. battery packs, rollers, axles, bearings arms, etc.)
Seller warrants the repair or replacement of the Product for the balance of the one (1) year warranty as stated above or ninety (90) days, whichever is longer.
Seller warrants the repair or replacement of the Product for ninety (90) days after shipment back to Customer.
For all the above-mentioned warranty terms, the warranty is valid only when recommended parts are used (i.e., parts listed in the parts list).