Professional Documents
Culture Documents
CF6 80c2tools Manual
CF6 80c2tools Manual
________________________________________________________
GE Aviation
Email: geae.csc@ge.com
Phone: (877) 432-3272
Fax: (513) 552-3329
SUBJECT: CF6-80C2 Illustrated Tool and Equipment Manual, GEK 92463. Revision No. 8,
Dated December 01, 2016.
The subject manual is attached to this letter of transmittal. Please insert the attached into your
copy of the affected publication using the List (s) of Effective Pages. All obsolete pages should
be discarded. Upon completion of this updating process, please make the appropriate entry on
the Record of Revisions page.
GE Aviation
Distribution Center
One Neumann Way, Maildrop NP11C
Cincinnati, Ohio 45215 USA
Phone: (513) 552-3272
Fax: (513) 552-3329
Email: geae.csc@ge.com
If you have any questions or comments regarding the content of this manual, or if you need
technical assistance or spare parts, please contact:
GE Aviation
Phone: (513) 552-3272
Email: geae.csc@ge.com
The following disclosure notice is to inform you of your obligations as a recipient of technical
information under U.S. Export laws.
GE PROPRIETARY INFORMATION
Regards,
GE Aviation
GEK 92463
GE Aviation
CF6-80C2
TURBOFAN ENGINE
1 Nov 01/1986
2 Oct 01/1988
3 Feb 15/1991
4 Apr 01/1998
5 Feb 28/2005
6 Dec 01/2012
7 Dec 01/2014
8 Dec 01/2016
ALL HIGHLIGHTS
Page 1
Dec 01/2016
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
LIST OF EFFECTIVE PAGES
CHAPTER/ CHAPTER/
SECTION PAGE DATE SECTION PAGE DATE
Introduction MSE-25C
132-6 MSE-28
AM-1200-80C2 MSE-28C
AM-1928 MSE-29
AM-1963-122 MSE-41
AM-1966 MSE-43
AM-1994 MSE-46A
MSE-14 MSE-46B
1 thru 2 Dec 01/2012 1 thru 2 Dec 01/2012
MSE-20A MSE-51B
1 thru 2 Dec 01/2012 1 thru 2 Feb 28/2005
MSE-22 MSE-52
1 thru 2 Dec 01/2012 1 thru 2 Dec 01/2012
MSE-22A MSE-53
1 thru 2 Feb 28/2005 1 thru 2 Feb 28/2005
MSE-24E MSE-54
1 thru 2 Dec 01/2012 1 thru 2 Feb 28/2005
MSE-24F MSE-55A
1 thru 1 Dec 01/2012 1 thru 2 Dec 01/2012
MSE-25 MSE-57
1 thru 1 Dec 01/2012 1 thru 2 Feb 28/2005
1. General.
NOTE: The following disclosure notice is to inform you of your obligations as a
recipient of technical information under U.S. Export laws:
The information contained in this document is GE proprietary information and
is disclosed in confidence. It is the property of GE and must not be used,
disclosed to others or reproduced without the express written consent of GE,
including, but without limitation, it is not to be used in the creation,
manufacture, development, or derivation of any repairs, modifications,
spare parts, designs, or configuration changes or to obtain FAA or any
other government or regulatory approval to do so. If consent is given for
reproduction in whole or in part, this notice and the notice set forth on each
page of this document must appear in any such reproduction in whole or in part.
2. Purpose of Manual.
This manual is provided to give the airline planners and engineers a
comprehensive listing of the special tools and equipment required for the
maintenance of the CF6-80C2 Turbofan Engine.
3. Scope of Information.
A. The tooling information contained in this manual is intended for
descriptive use only. Specific information applicable to tool usage must
be obtained from the official publications provided for that purpose.
B. The tools listed in this manual include:
(1) GE Aircraft Engine (2C) tools.
(2) GE Aircraft Engine standard part number (such as 1303M20P01) tools.
(3) Advanced Ground System Engineering (AM) tools.
(4) Manufactured Standard Equipment (MSE) tools.
(5) Rohr Support Equipment (RSE) tools.
(6) Starrett tools (such as 132-6).
4. Structure of Manual.
This manual is arranged in sections to present tooling information in an easy
to use format. Pages that have been changed or added by current revision are
identified by change bars.
A. The Alpha Numerical List section provides a list of the special tools in
alpha numerical sequence.
B. The Tool Data Sheet section provides specific information for each tool.
The data sheets are arranged in alpha numerical order according to tool
number and contain the following information.
(1) Tool Nomenclature and Number: Complete name of tool and its tool
number.
(2) Purpose and Use: General explanation of the tool application and the
intended use.
(3) Description: Brief description of the tool design and physical
construction.
ALL
GEK 92463
INTRODUCTION
Page 1
Dec 01/2014
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
(4) Dimensions: General overall dimensions expressed in inches and
centimeters or millimeters.
(5) Weight: Approximate weight in pounds and kilograms.
(6) Supporting Tools: Tools used in conjunction with or in support of
the subject tool.
(7) Tool Maintenance: General light maintenance of tools and
preservation.
(8) Quantity Per Operation: Number of tools necessary for intended use.
(9) Replacement Parts List: Consists of the detail parts subject to
wear, deterioration, or loss.
(10) Illustration: A perspective view of the tool.
5. Additional Technical Publications.
The operation and maintenance requirements for the support of the CF6-80C2
Turbofan Engine are covered by the following publications:
A. Engine Manual.
B. Component Maintenance Manuals.
C. Service Bulletins.
D. Aircraft Maintenance Manuals.
E. Standard Practice Manuals (including Consumable Products section).
F. Illustrated Parts Catalog.
6. Tool Drawings.
Tool drawings are available in printed form.
7. Customer Service.
Please direct any suggestions or comments regarding this manual to:
Commercial Jet Engine Operator Contacts
GE Aviation Operation Center
1 Neumann Way, Maildrop RM 285
Cincinnati, Ohio 45215 U.S.A.
Phone: (513) 552-3272
Toll Free: (877) 432-3272
Fax (513) 552-3329
email: geae.aoc@ge.com
ALL
GEK 92463
INTRODUCTION
Page 2
Dec 01/2014
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
8. Supplementary Information.
A. Definition of terms. Refer to Table 1.
TABLE 1. DEFINITION OF TERMS
Term Definition
Alternate This term indicates that this tool
can be used interchangeably for the
primary tool.
Deleted This term indicates that a tool is
no longer required for use with
these engines.
Superseded By This term indicates the
non-interchangeability of an old
tool for a new tool.
Supersedes This term indicates that a new tool has
been introduced for use and that the old
tool is no longer authorized for use.
Replaced By This term is used to denote that a
redesigned tool has been introduced and
can be used interchangeably with the
old tool. When ordering a replacement
tool, order the new tool.
Replaces This term is used to denote that a
redesigned tool has been introduced
to replace the old tool. The old
tool can continue to be used; however,
when ordering a replacement tool,
order the new tool.
9. Servicing of Tools.
A. Remove tools from service when lubrication or calibration is required and
when the following conditions are known or suspected:
(1) Tools are worn beyond usable limits.
(2) Tools have been dropped or misused.
(3) Tools do not work properly.
(4) Tools have been severely stressed during use.
(5) Tools have been cancelled.
B. Keep tools clean and free of grease except for occasional lubrication of
all movable bearing surfaces. Lubricate castors periodically when the
tool is in use.
C. Every 6 months, lightly lubricate all threads, splines, pivot points,
sliding surfaces, bearings, and all pressure surfaces. Wipe off excess
oil.
ALL
GEK 92463
INTRODUCTION
Page 3
Dec 01/2014
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
D. In areas where corrosion is a problem, it is recommended that an
application of corrosion preventive compound be applied every 6 months.
10. Inspection of Tools.
NOTE: Defective tools must be repaired or replaced to avoid damage to the
engine.
A. Inspect tools for high metal, cracks, or other visible defects which may
cause the tool to work improperly.
B. Slings and hoisting devices must be inspected prior to each use.
11. Calibration of Tools.
NOTE: Tools that have been dropped or otherwise damaged must be inspected and
calibrated before further use.
A. All measuring tools must be carefully examined for damage which
might affect the accuracy of readings. They also must be calibrated
periodically to maintain accuracy. After calibration the tool should be
tagged to show date of inspection, deviation for original setting, if any,
and other data which will aid in the next calibration.
B. Use standard precision instrument care. Refer to the Tool Data Sheets for
specific calibration information for those tools requiring calibration.
12. Care of Tools in Storage.
A. Clean all tools and apply a thin coat of rust inhibitor prior to storage.
B. Place tools in their own storage containers or wrap them in a suitable
barrier material.
C. Store tools in a clean dry area to reduce the risk of corrosion.
13. Replacement Parts List.
When ordering tools or replacement parts for a tool, specify the tool part
number (AM-XXXX, MSE-XXX, RSE-XXX, 2CXXXXX or GE number) and replacement part
detail number that is stamped on the replacement part.
ALL
GEK 92463
INTRODUCTION
Page 4
Dec 01/2014
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
ALPHA NUMERICAL LIST
ALL
132-6
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
ALL
132-6
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
SELF-ERECTING GANTRY
AM-1200-80C2
FOR ALL
AM-1200-80C2
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
AM-1200-80C2
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
SHIPPING AND STORAGE STAND
AM-1928
PURPOSE AND USE: The Shipping and Storage Stand is used to hold the
engine during shipping and storage.
DESCRIPTION: The Shipping and Storage Stand is a frame designed with attaching
brackets to secure the engine (QEC configuration) during shipping and storage.
DIMENSIONS: 170 x 100 x 107 in. (4,318 x 2,540 x 2,718 mm).
WEIGHT: 14,500 lbs (6,577 kg).
SUPPORTING TOOLS: AM-2389-3 FADEC Container (optional), AM-2390-3
Oil Tank Container (optional).
TOOL MAINTENANCE: Refer to vendor literature.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to vendor literature.
FOR ALL
AM-1928
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
AM-1928
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
MIDSHAFT SUPPORT - NO. 3 BEARING
AM-1963-122
PURPOSE AND USE: This fixture is to support the No. 3 bearing. It is part
of the core shipping and transportation stand, AM-1963, which is part of
the AM-1192-80C2 split engine transport system.
DESCRIPTION: It slides and clamps onto the end of the shaft then bolt
to the forward core support.
DIMENSIONS: 16 x 32 x 3 in. (406 x 813 x 76 mm).
WEIGHT: 30 lbs (14 kg).
SUPPORTING TOOLS: None.
TOOL MAINTENANCE: None.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Contact Advanced Ground Systems Engineering, LLC for information.
FOR ALL
AM-1963-122
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
AM-1963-122
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
CORE MODULE SHIPPING CONTAINER
AM-1966
PURPOSE AND USE: The Core Module Shipping Container is used to support
the core module during shipping.
DESCRIPTION: The Core Module Shipping Container is a large container with attaching
brackets inside to secure the core module during shipping. Tool vendor is AGSE. For
information, contact Advanced Ground Systems Engineering, LLC for information.
DIMENSIONS: 102 x 80 x 62 in. (2,591 x 2,032 x 1,575 mm).
WEIGHT: 800 lbs (363 kg).
SUPPORTING TOOLS: Refer to vendor literature.
TOOL MAINTENANCE: Refer to vendor literature.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to vendor literature.
FOR ALL
AM-1966
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
AM-1966
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
UNIVERSAL PNEUMATIC TIRE DOLLY
AM-1994
PURPOSE AND USE: The Pneumatic Tire Dolly is used to hold the engine
during shipping and storage.
DESCRIPTION: The Pneumatic Tire Dolly is an open frame construction with a tow bar
and four posts to hold AM-1928. Tool vendor is AGSE. For information, contact
Advanced Ground Systems Engineering, LLC, for information.
DIMENSIONS: 168 x 108 x 24 in. (4,267 x 2,743 x 610 mm).
WEIGHT: 2500 lbs (1134 kg).
SUPPORTING TOOLS: AM-1928.
TOOL MAINTENANCE: Refer to vendor literature.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to vendor literature.
FOR ALL
AM-1994
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
AM-1994
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
SOCKET, FAN ROTOR NUT NUMBER 30 SPLINE
MSE-14
PURPOSE AND USE: The Fan Rotor Nut Socket is used to remove
the nuts on the fan rotor.
DESCRIPTION: The Fan Rotor Nut Socket is a splined socket. The
socket has a black oxide finish.
DIMENSIONS: 1.75 x 1.25 in. (44 x 32 mm).
WEIGHT: 0.1 lb (0.05 kg).
SUPPORTING TOOLS: 1/2 in. Drive Ratchet Wrench.
TOOL MAINTENANCE: Apply corrosion preventive oil to all surfaces
that have a black oxide finish.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to vendor literature.
NOTE: For vendor information, contact Snap-On Tools Corp., 8049 28th
Avenue, Kenosha, WI 53140 U.S.A.
FOR ALL
MSE-14
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
MSE-14
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
TABLE, ROTARY, BALL BEARING
MSE-20A
PURPOSE AND USE: For assembly and runout checks of HPT rotor.
DESCRIPTION: It has 18 in. (457 mm) dia table top with 20 in. (508 mm) table
base. Table top drilled for 12 each 0.625-11 UNC-2B x 0.86-0.90 in. (22-23
mm) deep holes on a 13.250 in. (336.5 mm) dia circle.
DIMENSIONS: 20 in. dia x 3.5 in. (508 mm dia x 89 mm).
WEIGHT: TBD
SUPPORTING TOOLS: Use with 2C14011P03.
TOOL MAINTENANCE: See vendor catalog.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS LIST
PART NO. NOMENCLATURE QUANTITY SUPPLIER
CODE
MSE-20A Table, Rotary 1 DP
UR18-00003 Table, Rotary 1 EY
FOR ALL
MSE-20A
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
MSE-20A
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
POSITIONER
MSE-22
FOR ALL
MSE-22
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
MSE-22
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
POSITIONER
MSE-22A
FOR ALL
MSE-22A
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
MSE-22A
Page 2
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
TORQUE MULTIPLIER, 12,000 LB FT (16,270 N.M)
MSE-24E
PURPOSE AND USE: The 12,000 lb ft (16,270 N.m) Torque Multiplier is used
to apply a turning force to threaded components.
DESCRIPTION: The 12,000 lb ft (16,270 N.m) Torque Multiplier consists of
a torque multiplier wrench, pneumatic torque multiplier, torque wrench,
ratchet adapters, and a work handle.
DIMENSIONS: 18 x 6 x 26 in. (457 x 152 x 660 mm).
WEIGHT: 85 lbs (39 kg).
SUPPORTING TOOLS: None.
TOOL MAINTENANCE: Refer to vendor literature.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS LIST
PART NO. NOMENCLATURE QUANTITY SUPPLIER
CODE
SWE-53 Torque Wrench 1 DT
SWE-63B Work Handle 1 DT
SWE-67B Ratchet Adapter 1 DT
SWE-8200 Mechanical Torque 1 DT
Multiplier
SWE-8202 Pneumatic Torque 1 DT
Multiplier
SWE-948514 Adapter 1 DT
FOR ALL
MSE-24E
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
MSE-24E
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
DELETED
MSE-24F
PURPOSE AND USE: This tool has been deleted in its entirety.
FOR ALL
MSE-24F
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
DELETED
MSE-25
PURPOSE AND USE: This tool has been deleted in its entirety.
FOR ALL
MSE-25
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
TORQUE MULTIPLIER, 3,000 LB FT (4,067 N.M)
MSE-25C
FOR ALL
MSE-25C
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
MSE-25C
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
TORQUE MULTIPLIER - 50,000 LB FT (67,791 N.M)
MSE-27C
FOR ALL
MSE-27C
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
MSE-27C
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
DELETED
MSE-28
PURPOSE AND USE: This tool has been deleted in its entirety.
FOR ALL
MSE-28
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
WRENCH, LOCKING LUG - COMPRESSOR ROTOR
MSE-28C
PURPOSE AND USE: To loosen and tighten the locking lugs on the compressor rotor.
DESCRIPTION: Consists of a handle with set-screw and hexagonal driver bits.
DIMENSIONS: 3 x 4 x 2 (76 x 101 x 50 mm).
WEIGHT: 1 lb (0.5 kg).
SUPPORTING TOOLS: None.
TOOL MAINTENANCE: None.
QUANTITY PER OPERATION: One.
NOTE: For vendor information, contact MSC Industrial Supply, 75 Maxess Road,
Melville, NY, U.S.A. 11747-3151, Phone 516-812-2000.
REPLACEMENT PARTS LIST
PART NO. NOMENCLATURE QUANTITY SUPPLIER
CODE
185-0 Driver Bit 1 DU
185-1 Driver Bit 1 DU
64224207 5/64" T-Handle Standard 1
Hex Wrench
64224215 3/32" T-Handle Standard 1
Hex Wrench
FOR ALL
MSE-28C
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
MSE-28C
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
STAND, PERSONNEL - CORE ENGINE, VERTICAL
MSE-29
PURPOSE AND USE: To provide a secure work stand for vertical engine maintenance.
DESCRIPTION: A scaffolding of aluminum construction with stairsteps.
DIMENSIONS: 154 x 124 x 115 in. (3900 x 3150 x 2920 mm).
WEIGHT: TBD
SUPPORTING TOOLS: None.
TOOL MAINTENANCE: Refer to vendor literature.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS LIST
PART NO. NOMENCLATURE QUANTITY SUPPLIER
CODE
MSE-29 Stand, Jet Engine Maint. 1 DP
L-2005 Stand, Jet Engine Maint. 1 DV
FOR ALL
MSE-29
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
MSE-29
Page 2
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
PUMP, HYDRAULIC, HAND OPERATED
MSE-41
FOR ALL
MSE-41
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
MSE-41
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
WRENCH, SPANNER
MSE-43
PURPOSE AND USE: To aid in the assembly and disassembly of the thrust
reverser ball screw angle gearbox.
DESCRIPTION: One piece wrench with lugs to engage the nut.
DIMENSIONS: 7 x 2 x 2 in. (178 x 51 x 51 mm).
WEIGHT: 2.2 lb (1 kg).
SUPPORTING TOOLS: None.
TOOL MAINTENANCE: Apply a light coat of oil when stored.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS LIST
PART NO. NOMENCLATURE QUANTITY SUPPLIER
CODE
MSE-43 Wrench, Spanner 1 DP
196502 Wrench, Spanner 1 DT
FOR ALL
MSE-43
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
MSE-43
Page 2
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
DELETED
MSE-46A
PURPOSE AND USE: This tool has been deleted in its entirety.
FOR ALL
MSE-46A
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
DRIVE BITS, INTERNAL, TORX
MSE-46B
FOR ALL
MSE-46B
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
MSE-46B
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
TORQUE MULTIPLIER, 2200 LB FT (2983 N.M)
MSE-51B
FOR ALL
MSE-51B
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
MSE-51B
Page 2
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
SURFACE PLATE
MSE-52
NOTE: For vendor information, contact Tru-Stone Corporation, P.O. Box 430,
Waite Park, Minn. 56387, U.S.A., 1-800-959-0517.
REPLACEMENT PARTS LIST
PART NO. NOMENCLATURE QUANTITY SUPPLIER
CODE
48 x 72 x 10 in. Plate, Gray Granite 1
(1,219 x 1,829 Surface, Grade "A"
x 254 mm) Inspection
48 x 72 in. Stand, Stationary for 1
(1,219 x 1,829 Item 2
mm)
FOR ALL
MSE-52
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
MSE-52
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
LIFT SLING
MSE-53
PURPOSE AND USE: To lift stage-1 and stage-2 HPT nozzles and combustor.
DESCRIPTION: Consists of a ring, 3 stainless steel ropes, 1/4 x 36 in. (6.4 x 915
mm), and safety latches. Sling has a 2000 lb (909 kg) working load.
DIMENSIONS: Approx. 40 in. (1016 mm) long.
WEIGHT: 10 lb (4.5 kg).
SUPPORTING TOOLS: None.
TOOL MAINTENANCE: Periodically load test with a 4000 lb (1818 kg) static load.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS LIST
PART NO. NOMENCLATURE QUANTITY SUPPLIER
CODE
MSE-53 Sling, Lift, Safe-Guard 1 DP
E-3 Sling, Lift, Safe-Guard 1 AC
FOR ALL
MSE-53
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
MSE-53
Page 2
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FORCEPS
MSE-54
FOR ALL
MSE-54
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
MSE-54
Page 2
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
SCREWDRIVER SET, TORQ-SET
MSE-55A
FOR ALL
MSE-55A
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
MSE-55A
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
WRENCH, COUPLING NUT - LPT MID SHAFT
MSE-57
FOR ALL
MSE-57
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
MSE-57
Page 2
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
WRENCH, COUPLING NUT - LPT MID SHAFT
MSE-57A
FOR ALL
MSE-57A
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
MSE-57A
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
TORQ-SET DRIVER SET
MSE-63
PURPOSE AND USE: The Torq-Set Driver Set is used to remove and install
torq-set screws from the engine.
DESCRIPTION: The Torq-Set Driver Set consists of a 5/16 in. hex shank bit
and a 3/8 in. female squared drive bit holder.
DIMENSIONS: 2 x 0.3125 in. (51 x 7.938 mm).
WEIGHT: 0.1 lb (0.05 kg).
SUPPORTING TOOLS: Driver.
TOOL MAINTENANCE: TBD
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS LIST
PART NO. NOMENCLATURE QUANTITY SUPPLIER
CODE
170-3/8A Insert Bit, Torq-Set 1 DU
Screw, 3/8 in. Screw
Size, 5/16 in. Hex
Shank
835 Drive Bit Holder - 3/8 1 DU
in. Female Square
Drive, 5/16 in. Hex
Opening
FOR ALL
MSE-63
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
MSE-63
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
BACK LIGHTED CONFORMATION TOOL
MSE-64
FOR ALL
MSE-64
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
MSE-64
Page 2
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
PLIERS, INSTALL AND REMOVE, RETAINING RING - FAN FWD AND MID SHAFT ASSY
MSE-66A
PURPOSE AND USE: The Install and Remove Retaining Ring Pliers are used to install
and remove the internal keyed ring in the fan forward/mid shaft assembly.
DESCRIPTION: The Install and Remove Retaining Ring Pliers are modified
standard pliers No. 0900 with standard 0900-12 tips.
DIMENSIONS: 14 in. (356 mm).
WEIGHT: 1 lb (0.5 kg).
SUPPORTING TOOLS: None.
TOOL MAINTENANCE: None.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing MSE-66A.
FOR ALL
MSE-66A
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
MSE-66A
Page 2
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
HPC BLADE BORESCOPE BLENDING TOOL
MSE-79
PURPOSE AND USE: The HPC Blade Borescope Blending Tool is used to repair
installed HPC blades found with unserviceable damage.
DESCRIPTION: The HPC Blade Borescope Blending Tool is a borescope, drive motor power
supply, borescope light projector, fiber light cable, and four grinding tips.
DIMENSIONS: Refer to vendor literature.
WEIGHT: Refer to vendor literature.
SUPPORTING TOOLS: Refer to vendor literature.
TOOL MAINTENANCE: Refer to vendor literature.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing MSE-79.
FOR ALL
MSE-79
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
MSE-79
Page 2
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
DOLLY, INLET COWL
RSE-1021-3B
PURPOSE AND USE: The Inlet Cowl Dolly is used to support the inlet
cowl during transport or storage.
DESCRIPTION: The Inlet Cowl Dolly consists of a foldable platform
on casters and a tow bar.
DIMENSIONS: Assembled: 161 x 120 x 130 in. (4,089 x 3,048 x 3,302 mm).
Disassembled: 84 x 120 x 62 in. (2,134 x 3,048 x 1,575 mm).
WEIGHT: 2,350 lbs (1,066 kg).
SUPPORTING TOOLS: None.
TOOL MAINTENANCE: Keep clean and free of grease except for occasional
oiling of all movable bearing surfaces.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing RSE-1021.
NOTE: This is a Rohr Support Equipment (RSE) tool, FSCM code 51563.
For information contact BF Goodrich.
FOR ALL
RSE-1021-3B
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
RSE-1021-3B
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
SLING, INLET COWL
RSE-1024-1A
PURPOSE AND USE: The Inlet Cowl Sling is used to lift and handle the inlet
cowl and to install or remove it from an aircraft.
DESCRIPTION: The Inlet Cowl Sling is made of wire rope, chains, turnbuckles, and
four attach pads all joined together at the top with a single link.
DIMENSIONS: Assembled: 12 x 12 x 12 in. (305 x 305 x 305 mm).
WEIGHT: 15 lbs (7 kg).
SUPPORTING TOOLS: None.
TOOL MAINTENANCE: Keep unit clean and dry during storage.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing RSE-1024.
NOTE: This is a Rohr Support Equipment (RSE) tool, FSCM code 51563.
For information contact BF Goodrich.
FOR ALL
RSE-1024-1A
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
RSE-1024-1A
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
SLING, FAN COWL
RSE-1025-1
PURPOSE AND USE: To support the fan cowls during installation or removal and
to provide a means of attachment for transport by crane.
DESCRIPTION: The sling consists of three legs of nylon webbing. Two of
the legs are adjustable in order to allow the ordered angles of suspension
to permit matching the pylon hinges. Each leg has an attachment pad
to effect safe attachment to the cowls.
DIMENSIONS: 10 x 10 x 10 in. (packaged) (254 x 254 x 254 mm).
WEIGHT: 8 lbs (3.6 kg).
SUPPORTING TOOLS: None.
TOOL MAINTENANCE: Keep unit clean and dry during storage.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: See drawing.
NOTE: This is a Rohr Support Equipment (RSE) tool, FSCM code 51563.
For information contact BF Goodrich.
FOR ALL
RSE-1025-1
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
RSE-1025-1
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
SLING, PRIMARY NOZZLE
RSE-1026-1
PURPOSE AND USE: The Primary Nozzle Sling is used to handle the primary
nozzle except for installation under the wing.
DESCRIPTION: The Primary Nozzle Sling is two wire supports on a spreader beam. A
system of arms are used to allow rotation of the part about its center of gravity.
DIMENSIONS: 65 x 12 x 12 in. (1,651 x 305 x 305 mm).
WEIGHT: 10 lbs (5 kg).
SUPPORTING TOOLS: None.
TOOL MAINTENANCE: Keep unit clean and dry during storage.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing RSE-1026.
NOTE: This is a Rohr Support Equipment (RSE) tool, FSCM code 51563.
For information contact BF Goodrich.
FOR ALL
RSE-1026-1
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
RSE-1026-1
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
ACCESSORIES HOIST SYSTEM
RSE-1027-1
PURPOSE AND USE: The Accessories Hoist System is used to position and
hold the IDG during installation or removal.
DESCRIPTION: The Accessories Hoist System consists of a hydraulic jack on
wheels, a strap, and an adapter to hold the IDG.
DIMENSIONS: 36 x 36 x 42 in. (914 x 914 x 1,067 mm).
WEIGHT: 176 lbs (80 kg).
SUPPORTING TOOLS: None.
TOOL MAINTENANCE: Maintain free of dirt and grease. Periodically
check the fluid level.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing RSE-1027.
NOTE: This is a Rohr Support Equipment (RSE) tool, FSCM code 51563.
For information contact BF Goodrich.
FOR ALL
RSE-1027-1
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
RSE-1027-1
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
DOLLY, FAN COWL DOOR
RSE-1028-3B
PURPOSE AND USE: The Fan Cowl Door Dolly is used to store and transport
one set of engine fan cowls.
DESCRIPTION: The Fan Cowl Door Dolly is provided with a tow bar in the front
and a pintle hook in the rear to allow train towing in line by a tractor. It
allows standing the cowls on edges and provides tie downs to prevent damage
from shifting by wind blast or cornering. The dolly can be disassembled to
fit into a standard container for shipping by aircraft.
DIMENSIONS: Assembled: 140 x 84 x 18 in. (3,556 x 2,134 x 457 mm). Disassembled:
84 x 80 x 24 in. (2,134 x 2,032 x 610 mm).
WEIGHT: 850 lbs (386 kg).
SUPPORTING TOOLS: None.
TOOL MAINTENANCE: TBD
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing RSE-1028.
NOTE: This is a Rohr Support Equipment (RSE) tool, FSCM code 51563.
For information contact BF Goodrich.
FOR ALL
RSE-1028-3B
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
RSE-1028-3B
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
DOLLY, PRIMARY NOZZLE STORAGE
RSE-1029-1
NOTE: This is a Rohr Support Equipment (RSE) tool, FSCM code 51563.
For information contact BF Goodrich.
FOR ALL
RSE-1029-1
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
RSE-1029-1
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
COVER, PRIMARY NOZZLE
RSE-1033-1A
PURPOSE AND USE: The Primary Nozzle Cover is used to close the primary nozzle
area and prevent the entrance of foreign material in the engine.
DESCRIPTION: The Primary Nozzle Cover is made of glass cloth and resin
build-up molded to fit snugly into the engine exhaust nozzle. It
is retained there by friction.
DIMENSIONS: 60 x 12 in. (1,524 x 305 mm).
WEIGHT: 35 lbs (16 kg).
SUPPORTING TOOLS: None.
TOOL MAINTENANCE: Keep clean and free of oil and grease.
QUANTITY PER OPERATION: One per engine.
REPLACEMENT PARTS: Refer to drawing RSE-1033.
NOTE: This is a Rohr Support Equipment (RSE) tool, FSCM code 51563.
For information contact BF Goodrich.
FOR ALL
RSE-1033-1A
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
RSE-1033-1A
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
DELETED
RSE-1035-1A
PURPOSE AND USE: This tool has been deleted in its entirety.
FOR ALL
RSE-1035-1A
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
DELETED
RSE-1035-1M
PURPOSE AND USE: This tool has been deleted in its entirety.
FOR ALL
RSE-1035-1M
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
DELETED
RSE-1036-1A
PURPOSE AND USE: This tool has been deleted in its entirety.
FOR ALL
RSE-1036-1A
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
DELETED
RSE-1036-1M
PURPOSE AND USE: This tool has been deleted in its entirety.
FOR ALL
RSE-1036-1M
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
PINS, LOCATING FAN AND CORE COWL HINGES
RSE-1037-1
PURPOSE AND USE: To align the three sets of hinge halves on the cowl
doors before inserting the bolt.
DESCRIPTION: The pins have bullet nose shape with diameter which is snug fit in the
bolt hole. The handle is knurled to give a sure grip and reduce mishandling.
DIMENSIONS: 0.5 x 4 in. (12.7 x 101.6 mm).
WEIGHT: 0.22 lb (0.10 kg).
SUPPORTING TOOLS: None.
TOOL MAINTENANCE: Keep clean and dry.
QUANTITY PER OPERATION: Three.
REPLACEMENT PARTS: See drawing.
NOTE: This is a Rohr Support Equipment (RSE) tool, FSCM code 51563.
For information contact BF Goodrich.
FOR ALL
RSE-1037-1
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
RSE-1037-1
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
DOLLY, CORE COWL
RSE-1039
PURPOSE AND USE: To store and transport one set of core cowl doors.
DESCRIPTION: This steel constructed dolly with 8 in. (203.2 mm) castors is intended
to be towed by a tractor from the shop to the line station or vice versa.
DIMENSIONS: 120 x 84 x 96 in. (3,048 x 2,134 x 2,438 mm).
WEIGHT: 2,536 lbs (1,151 kg).
SUPPORTING TOOLS: None.
TOOL MAINTENANCE: Keep clean and free from grease except for occasional
oiling of movable bearing surfaces.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: See drawing.
NOTE: This is a Rohr Support Equipment (RSE) tool, FSCM code 51563.
For information contact BF Goodrich.
FOR ALL
RSE-1039
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
RSE-1039
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
PIN, RIG
RSE-1041-3
PURPOSE AND USE: The Rig Pin is used in rigging the fuel control system.
DESCRIPTION: The Rig Pin is a round rod with chamfered ends.
DIMENSIONS: 0.1865-0.1870 in. dia x 4.9-5.1 in. (4.7371-4.7498
mm dia x 124.46-129.54 mm).
WEIGHT: 0.5 lb (0.23 kg).
SUPPORTING TOOLS: None.
TOOL MAINTENANCE: Keep the tool clean and dry.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing RSE-1041.
NOTE: This is a Rohr Support Equipment (RSE) tool, FSCM code 51563.
For information contact BF Goodrich.
FOR ALL
RSE-1041-3
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
RSE-1041-3
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
DELETED
RSE-1042-1
PURPOSE AND USE: This tool has been deleted in its entirety.
FOR ALL
RSE-1042-1
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
WRENCH
RSE-1060-1
PURPOSE AND USE: The Wrench is used to tighten the anti-ice duct connection
in the inlet cowl assembly to specific torque values.
DESCRIPTION: The Wrench is a steel castellated type with square
drive hole for torque wrench use.
DIMENSIONS: 5 x 7 x 12 in. (127 x 178 x 305 mm).
WEIGHT: 2 lbs (1 kg).
SUPPORTING TOOLS: Torque Wrench.
TOOL MAINTENANCE: Keep clean and dry.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing RSE-1060.
NOTE: This is a Rohr Support Equipment (RSE) tool, FSCM code 51563.
For information, contact BF Goodrich.
FOR ALL
RSE-1060-1
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
RSE-1060-1
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
COVER, INLET COWL
RSE-1061-1A
PURPOSE AND USE: The Inlet Cowl Cover is used to prevent entry of foreign
material into the engine during parking or mooring.
DESCRIPTION: The Inlet Cowl Cover is predominately nylon/vinyl cloth with
adjustable attachment straps to hold it in place.
DIMENSIONS: 12 x 36 x 36 in. (305 x 914 x 914 mm).
WEIGHT: 45 lbs (20 kg).
SUPPORTING TOOLS: None.
TOOL MAINTENANCE: Store in a cool, dry place out of sunlight.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing RSE-1061.
NOTE: This is a Rohr Support Equipment (RSE) tool, FSCM code 51563.
For information, contact BF Goodrich.
FOR ALL
RSE-1061-1A
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
RSE-1061-1A
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
PLUG, ANTI-ICE OVERBOARD VENT
RSE-1062
PURPOSE AND USE: To prevent entry of foreign material into the inlet cowl
assembly through the anti-ice overboard vent.
DESCRIPTION: The plug is made of 0.125 in. (3.2 mm) plastic sheet, formed to fit
and retain in itself by friction in the anti-ice vent opening.
DIMENSIONS: 5 x 10 x 12 in. (127 x 254 x 304.8 mm).
WEIGHT: 1 lb (0.5 kg).
SUPPORTING TOOLS: None.
TOOL MAINTENANCE: None.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: See drawing.
NOTE: This is a Rohr Support Equipment (RSE) tool, FSCM code 51563.
For information, contact BF Goodrich.
FOR ALL
RSE-1062
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
RSE-1062
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
ALIGNMENT TOOL
RSE-1070-1
PURPOSE AND USE: The Alignment Tool is used to align the components of the inlet
cowl so that the attaching bolt pattern will match the engine front flange.
DESCRIPTION: The Alignment Tool is a large round tool which fits onto the
aft flange of the inlet cowl and is used to define a plane area for use in
assembly or repair operation on the inlet cowl.
DIMENSIONS: 100 x 18 in. (2,540 x 457 mm).
WEIGHT: 170 lbs (77 kg).
SUPPORTING TOOLS: None.
TOOL MAINTENANCE: Keep clean, dry, and store flat.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing RSE-1070.
NOTE: This is a Rohr Support Equipment (RSE) tool, FSCM code 51563.
For information contact BF Goodrich.
FOR ALL
RSE-1070-1
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
RSE-1070-1
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
SPANNER SET — GENERAL
RSE-1071
PURPOSE AND USE: The Wrench Set is used to tighten the anti-ice duct connection
in the fan cowl assembly to specific torque values.
DESCRIPTION: The Wrench Set is carbon steel with a square drive hole.
DIMENSIONS: Wrench Nut - 4 x 7 in. (102 x 178 mm).
Wrench Union - 3 x 12 in. (76 x 305 mm).
WEIGHT: Wrench Nut - 2 lbs (0.9 kg).
Wrench Union - 3 lbs (1 kg).
SUPPORTING TOOLS: Torque Wrench.
TOOL MAINTENANCE: Keep clean and dry.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing RSE-1071.
NOTE: This is a Rohr Support Equipment (RSE) tool, FSCM code 51563.
For information, contact BF Goodrich.
FOR ALL
RSE-1071
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
RSE-1071
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
DELETED
RSE-1071-3
PURPOSE AND USE: This tool has been deleted in its entirety.
FOR ALL
RSE-1071-3
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FIXTURE, EXHAUST PLUG INSTALLATION AND REMOVAL
RSE-1078-1
PURPOSE AND USE: The Exhaust Plug Installation and Removal Fixture is used
to install and remove the exhaust nozzle plug.
DESCRIPTION: The Exhaust Plug Installation and Removal Fixture is a folding
support which can hold the exhaust plug in position for bolt installation or
removal and then can be folded up for removal from the nozzle.
DIMENSIONS: 28 x 4 x 12 in. (711 x 102 x 305 mm).
WEIGHT: 8 lbs (4 kg).
SUPPORTING TOOLS: None.
TOOL MAINTENANCE: Keep clean and dry.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing RSE-1078.
NOTE: This is a Rohr Support Equipment (RSE) tool, FSCM code 51563.
For information, contact BF Goodrich.
FOR ALL
RSE-1078-1
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
RSE-1078-1
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FIXTURE, PRIMARY NOZZLE
RSE-1080-1
PURPOSE AND USE: The Primary Nozzle Fixture is used to store the primary nozzle.
DESCRIPTION: The Primary Nozzle Fixture is a yoke holding fixture mounted
on a steel plate with provisions for handling by a forklift. The nozzle
is retained by a nylon webbed strap.
DIMENSIONS: 66 x 54 x 64 in. (1,676 x 1,372 x 1,626 mm).
WEIGHT: 294 lbs (133.5 kg).
SUPPORTING TOOLS: None.
TOOL MAINTENANCE: None.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing RSE-1080-1.
NOTE: This is a Rohr Support Equipment (RSE) tool, FSCM code 51563.
For information, contact BF Goodrich.
FOR ALL
RSE-1080-1
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
RSE-1080-1
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
DOLLY, PRIMARY EXHAUST CENTERBODY STORAGE
RSE-1081-1
PURPOSE AND USE: The Primary Exhaust Centerbody Storage Dolly is used to
transport or store the centerbody parts.
DESCRIPTION: The Primary Exhaust Centerbody Storage Dolly is made of mild
structural steel. It has four 8 in. (203 mm) wheels. The front two are
free to rotate to allow easy maneuvering.
DIMENSIONS: 92 x 52 x 65 in. (2,337 x 1,321 x 1,651 mm).
WEIGHT: 370 lbs (168 kg).
SUPPORTING TOOLS: None.
TOOL MAINTENANCE: Keep clean and free from grease except for the occasional
oiling of movable bearing surfaces.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing RSE-1081-1.
NOTE: This is a Rohr Support Equipment (RSE) tool, FSCM code 51563.
For information, contact BF Goodrich.
FOR ALL
RSE-1081-1
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
RSE-1081-1
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
PULLER, VENTURI
RSE-1140
PURPOSE AND USE: To remove venturi from flange located in the 8th stage ducts.
DESCRIPTION: The puller consists of three jaws, a center body with tension
spring, bell housing and puller bolt. The jaws are inserted through the venture
where they grip the back of the venturi. The bell housing pushes against the
flange when the nut is tightened to remove the venturi.
DIMENSIONS: 4.75 in. dia x 10 in. (120.6 mm dia x 254 mm).
WEIGHT: 10 lbs (4.5 kg).
SUPPORTING TOOLS: 9/16 combination wrench.
TOOL MAINTENANCE: Lightly coat with oil.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: See drawing.
NOTE: This is a Rohr Support Equipment (RSE) tool, FSCM code 51563.
For information, contact BF Goodrich.
FOR ALL
RSE-1140
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
RSE-1140
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
TORQUE ADAPTER TOOL
RSE-1165
PURPOSE AND USE: To check torque setting of the pressure relief latches.
DESCRIPTION: The torque adapter tool is made of carbon steel, with a square
drive hole on one end for a torque wrench square drive insert and a tapered
tang on opposite end to insert into the latch bolt.
DIMENSIONS: 0.375 x 1 x 2 in. (9.5 x 25.4 x 50.8 mm).
WEIGHT: 0.200 lb (0.09 kg).
SUPPORTING TOOLS: 3/8-in. drive torque wrench.
TOOL MAINTENANCE: Keep clean and dry.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: See drawing.
NOTE: This is a Rohr Support Equipment (RSE) tool, FSCM code 51563.
For information, contact BF Goodrich.
FOR ALL
RSE-1165
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
RSE-1165
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
HOIST, BELLMOUTH
RSE-1181
PURPOSE AND USE: To lift the bellmouth for removal and installation from the engine.
DESCRIPTION: The sling is provided with two two-hole pads attached to cable to
locate on threaded inserts on barrel. It also has two clevis bolts attached
through lift holes in the attach ring of the bellmouth.
DIMENSIONS: 4 x 4 x 89 in. (101.6 x 101.6 x 2,260.6 mm).
WEIGHT: 18 lbs (8.2 kg).
SUPPORTING TOOLS: None.
TOOL MAINTENANCE: Periodically check bolts for thread wear. Check
cable for fraying and separation.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: See drawing.
NOTE: This is a Rohr Support Equipment (RSE) tool, FSCM code 51563.
For information, contact BF Goodrich.
FOR ALL
RSE-1181
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
RSE-1181
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
HOIST ACCESSORY SYSTEM, IDG - 120KVA
RSE-1183-101
PURPOSE AND USE: The integrated drive generator (IDG) Hoist Accessory System is
used to position and hold the IDG during installation or removal.
DESCRIPTION: The IDG Hoist Accessory System is comprised of a hydraulic jack
and an adapter to fit and securely hold the IDG.
DIMENSIONS: 36 x 36 x 55 in. (914 x 914 x 1,397 mm).
WEIGHT: 180 lbs (82 kg).
SUPPORTING TOOLS: None.
TOOL MAINTENANCE: Maintain free of dirt and grease. Check fluid level periodically.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing RSE 1183.
NOTE: This is a Rohr Support Equipment (RSE) tool, FSCM code 51563.
For information, contact BF Goodrich.
FOR ALL
RSE-1183-101
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
RSE-1183-101
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
ALIGNMENT TOOL, ECS DUCT
RSE-1196
NOTE: This is a Rohr Support Equipment (RSE) tool, FSCM code 51563.
For information, contact BF Goodrich.
FOR ALL
RSE-1196
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
RSE-1196
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
ALIGNMENT TOOL, ECS DUCT
RSE-1197
NOTE: This is a Rohr Support Equipment (RSE) tool, FSCM code 51563.
For information, contact BF Goodrich.
FOR ALL
RSE-1197
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
RSE-1197
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
ALIGNMENT TOOL, ECS DUCT
RSE-1198
NOTE: This is a Rohr Support Equipment (RSE) tool, FSCM code 51563.
For information, contact BF Goodrich.
FOR ALL
RSE-1198
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
RSE-1198
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
WRENCH, SPANNER
RSE-1202
PURPOSE AND USE: To adjust the environmental control system tolerance take-up
duct for adjustment to fit the mating flanges.
DESCRIPTION: This tool is made from forged steel and has an adjustable
head with a hook to engage the notched ring.
DIMENSIONS: 4.5 x 12 in. (114.3 x 304.8 mm).
WEIGHT: 1 lb (0.5 kg).
SUPPORTING TOOLS: None.
TOOL MAINTENANCE: Keep clean and dry.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: See drawing.
NOTE: This is a Rohr Support Equipment (RSE) tool, FSCM code 51563.
For information, contact BF Goodrich.
FOR ALL
RSE-1202
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
RSE-1202
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
ALIGNMENT TOOL
RSE-1206
PURPOSE AND USE: To align the components of an inlet cowl so that the attaching
bolt pattern will match the engine front flange.
DESCRIPTION: This tool is a large round tool which fits onto the aft
flange of the inlet cowl and is used to define a plane area for use in
assembly or repair operation on the inlet cowl.
DIMENSIONS: 100 in. dia x 18 in. (2,540 mm dia x 457 mm).
WEIGHT: 180 lbs (81.8 kg).
SUPPORTING TOOLS: None.
TOOL MAINTENANCE: Keep clean, dry, and store flat.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: See drawing.
NOTE: This is a Rohr Support Equipment (RSE) tool, FSCM code 51563 and is supplied
by BF Goodrich. For information, contact BF Goodrich.
FOR ALL
RSE-1206
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
RSE-1206
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
SLING, CORE COWL
RSE-1210
PURPOSE AND USE: To provide a means of handling the core cowl for left hand
or right hand during installation or removal.
DESCRIPTION: The sling consists of three cable legs. Each leg has a
pad to attach to the cowl hoist points.
DIMENSIONS: 10 x 10 x 10 in. (254 x 254 x 254 mm).
WEIGHT: 8 lbs (3.6 kg).
SUPPORTING TOOLS: None.
TOOL MAINTENANCE: Keep unit clean and dry during storage.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: See drawing.
NOTE: This is a Rohr Support Equipment (RSE) tool, FSCM code 51563.
For information, contact BF Goodrich.
FOR ALL
RSE-1210
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
RSE-1210
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
ROUTER TOOL GUIDE
RSE-1233
NOTE: This is a Rohr Support Equipment (RSE) tool, FSCM code 51563, and is
supplied by BF Goodrich. For information, contact BF Goodrich.
FOR ALL
RSE-1233
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
RSE-1233
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
PROBE, PRESSURE
1303M20P01
PURPOSE AND USE: The Pressure Probe is used to check the low pressure
turbine (LPT) inlet pressure.
DESCRIPTION: The Pressure Probe is a small wand with four openings along
the probe and a connector on the end of the housing. This pressure
probe is the equivalent of GE-CTF-341.
DIMENSIONS: 0.8 x 8 in. (20 x 203 mm).
WEIGHT: 0.5 lb (0.2 kg).
SUPPORTING TOOLS: TBD
TOOL MAINTENANCE: TBD
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing 1303M20.
FOR ALL
1303M20P01
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
1303M20P01
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FIXTURE, PULLER - EXHAUST GAS TEMPERATURE PROBE
9429M49P01
PURPOSE AND USE: This fixture is used to test the EGT probe puller.
DESCRIPTION: This tool consists of a pivot plate with a threaded rod attached,
two finger clamps, a locking bracket, a bronze thrust bearing, an adapter with
a 0.75 in. (19.05 mm) hex surface on the top and a threaded hole, a retainer
that holds the thrust bearing and the adapter together against the locking
bracket, and a Snap-On brand puller, that is threaded into the adapter. All
steel components will have a black oxide or black phosphate finish.
DIMENSIONS: 26 x 7 x 2 in. (660.4 x 117.8 x 50.8 mm).
WEIGHT: 15 lbs (6.8 kg).
SUPPORTING TOOLS: None.
TOOL MAINTENANCE: Coat treated surface with corrosion preventive oil.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing 9429M49.
FOR ALL
9429M49P01
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
9429M49P01
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
CONTROLLER, HEATER-RESISTIVE ELEMENT
9446M18P01
PURPOSE AND USE: This fixture is used to provide heat and temperature control
of engine hardware during assembly and disassembly.
DESCRIPTION: The resistive element heater controller is a self-contained, portable
unit enclosed in an industry-standard sloped front 19 inch (483 mm) rack style
enclosure made of steel. Because of its light weight and portability, it can
be conveniently positioned at the point of use. All instruments, controls and
interface cable connections used for operation and testing are located on the main,
top and side panels of the unit. Connection cables are not provided.
DIMENSIONS: 25.0 x 14.3 x 12.5 in. (6.4 x 363.2 x 317.5 mm).
WEIGHT: 65 lbs (29.5 kg).
SUPPORTING TOOLS: Refer to vendor literature.
TOOL MAINTENANCE: Refer to vendor literature.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to vendor literature.
FOR ALL
9446M18P01
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
9446M18P01
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
PROGRAM, BALANCE - BLADE INSTALLATION/REPLACEMENT
9446M61G02
FOR ALL
9446M61G02
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
9446M61G02
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
PROGRAM, BALANCE - BLADE INSTALLATION/REPLACEMENT
9446M61G03
FOR ALL
9446M61G03
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
9446M61G03
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
TEST STAND, ASSEMBLY - LUBE SYSTEM AIRFLOW
9461M37G01
PURPOSE AND USE: The Test Stand is used to pressure test the lube system for leaks.
DESCRIPTION: The Test Stand is a cart on wheels with a control panel on
the front and a storage compartment under the panel. There are brackets
to store the cables on the side.
DIMENSIONS: 24 x 24 x 57 in. (610 x 610 x 1448 mm).
WEIGHT: TBD
SUPPORTING TOOLS: TBD
TOOL MAINTENANCE: TBD
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing 9461M37.
NOTE: This tool is obsolete and was superseded by test stand 9461M40G01
(115 VAC) and 9461M40G02 (230 VAC).
FOR ALL
9461M37G01
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
9461M37G01
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
TEST STAND, ASSEMBLY LUBE SYSTEM AIRFLOW
9461M40G01
PURPOSE AND USE: The test stand is used to pressure test the lube system for leaks.
DESCRIPTION: The tool consists of a console made from an altered commercial item.
It has a working panel exceeding dimensions to the front side for ergonomics. The
console has an ergonomic inclined panel for watching the readings and to set the
equipment during its use. The console has four casters for mobility, and it has
lifting provisions to allow lifting with trucks at a standardized spread. The
front door and the rear door of the console can be opened to allow handling of
internal components. It works with an input voltage of 115 VAC.
DIMENSIONS: 60 x 24 x 24 in. (1,524 x 610 x 610 mm).
WEIGHT: 400 lbs (181.4 kg).
SUPPORTING TOOLS: Power supply (115 VAC), air supply [50.76/101.5 psi
(3.50/7.0 bar)], universal adapter kit (PN 9429M63).
TOOL MAINTENANCE: None.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing 9461M40.
FOR ALL
9461M40G01
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
9461M40G01
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
TEST STAND, ASSEMBLY LUBE SYSTEM AIRFLOW
9461M40G02
PURPOSE AND USE: The test stand is used to pressure test the lube system for leaks.
DESCRIPTION: The tool consists of a console made from an altered commercial item.
It has a working panel exceeding dimensions to the front side for ergonomics. The
console has an ergonomic inclined panel for watching the readings and set the
equipment during its use. The console has four casters for mobility, and it has
lifting provisions to allow lifting with trucks at a standardized spread. The
front door and the rear door of the console can be opened to allow handling of
internal components. It works with an input voltage of 230 VAC.
DIMENSIONS: 60 x 24 x 24 in. (1,524 x 610 x 610 mm).
WEIGHT: 400 lbs (181.4 kg).
SUPPORTING TOOLS: Power supply (230 VAC), air supply [50.76/101.5 psi
(3.50/7.0 bar)], universal adapter kit (PN 9429M63).
TOOL MAINTENANCE: None.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing 9461M40.
FOR ALL
9461M40G02
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
9461M40G02
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
GUIDE, FAN SHAFT ASSEMBLY, INSTALLATION AND REMOVAL
2C6010G05
FOR ALL
2C6010G05
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C6010G05
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
SLING, LIFT, FAN MIDSHAFT
2C6011G02
PURPOSE AND USE: To hoist/handle the fan midshaft when removed from the engine.
DESCRIPTION: The fan shaft lift sling consists of a square, tubular steel spreader
bar with swivel hooks on each end. A lift eye is welded to the center of the
spreader bar. Two nylon straps with aluminum eyes are provided to support
either the fan midshaft of the fan midshaft assembly.
DIMENSIONS: 60 x 4 x 2 in. (1,525 x 101.6 x 51 mm).
WEIGHT: 35 lbs (15.9 kg).
SUPPORTING TOOLS: Overhead hoist (fixed or portable).
TOOL MAINTENANCE: Load test periodically (see GE drawing 2C6011 for
load test diagram and applicable NOTE).
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS LIST
GROUP PART NO. NOMENCLATURE QUANTITY SUPPLIER
NUMBER CODE
G02 2C6011P02 Spreader Bar 1
EN-lA x 4.0 ft. Lift Slings 2 AD
in length
S-3316 (0.5 ton) Safety Hook 2 AB
FOR ALL
2C6011G02
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C6011G02
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
TRUCK, FAN SHAFT
2C6012G01
PURPOSE AND USE: To transport and store midfan shaft and forward fan shaft.
DESCRIPTION: This tool consists of a four wheeled hand truck with provisions
for holding midfan shaft or forward fan shaft.
DIMENSIONS: 126 x 17 x 30 in. (3,200 x 430 x 760 mm).
WEIGHT: 245 lbs (111 kg).
SUPPORTING TOOLS: 2C6011.
TOOL MAINTENANCE: Lubricate casters periodically.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS LIST
GROUP PART NO. NOMENCLATURE QUANTITY SUPPLIER
NUMBER CODE
G01 2C6012P02 Handle 1
2C6012P03 Base 1
2C6012P04 Clamp 2
2C6012P05 Vee Block 2
R-MS-6D Rigid Caster 2 N
S-MS-6D Swivel Caster 2 N
TL-75 Floor Lock 1 N
FOR ALL
2C6012G01
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C6012G01
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
SLING, LIFT - COMPRESSOR ROTOR
2C6013G05
FOR ALL
2C6013G05
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C6013G05
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
SLING, LIFT - COMPRESSOR ROTOR
2C6013G06
FOR ALL
2C6013G06
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C6013G06
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FIXTURE, VERTICAL LIFT - COMPRESSOR STATOR HALF
2C6016G04
FOR ALL
2C6016G04
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C6016G04
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
TOOL SET, HOLDING - VARIABLE STATOR VANE
2C6018G01
FOR ALL
2C6018G01
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C6018G01
Page 2
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
DRIVER SET - COMPRESSOR STATOR VANE
2C6019G02
PURPOSE AND USE: The Driver Set is used to position the vanes and vane
segments in the stator grooves.
DESCRIPTION: The G02 Driver Set contains a plastic driver used for
compressor stator vanes stages 7 thru 12.
DIMENSIONS: 10 x 6 x 1 in. (254 x 152.4 x 25.4 mm).
WEIGHT: 1 lb (0.45 kg).
SUPPORTING TOOLS: A Mallet that is not made of metal.
TOOL MAINTENANCE: None.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing 2C6019.
FOR ALL
2C6019G02
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C6019G02
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
DRIVER SET - COMPRESSOR STATOR VANE
2C6019G03
PURPOSE AND USE: The Driver Set is used to position the vanes and vane
segments in the stator grooves.
DESCRIPTION: The G03 Driver Set contains two drivers made of plastic. One
is used for compressor stator vanes stages 7 thru 12 and the other is
used for compressor stator vane stage 13.
DIMENSIONS: 10 x 6 x 4 in. (254 x 152.4 x 101.6 mm).
WEIGHT: 6 lbs (3 kg).
SUPPORTING TOOLS: A Mallet that is not made of metal.
TOOL MAINTENANCE: None.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing 2C6019.
FOR ALL
2C6019G03
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C6019G03
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
DELETED
2C6024G06
PURPOSE AND USE: This tool has been deleted in its entirety.
Superseded by tool 2C6024G07.
FOR ALL
2C6024G06
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
TRUCK - COMPRESSOR ROTOR
2C6024G07
PURPOSE AND USE: To transport and store compressor rotor and also to pivot
rotor when changing from a horizontal to vertical position.
DESCRIPTION: A welded stand with casters and floor locks. Both support rings pivot
so that the rotor can be lifted vertically from one of the two ends. Front and
rear supports collapse for clearance. The stand is to be pushed by hand.
DIMENSIONS: 41 x 75 x 12 in. (1,041 x 1,905 x 305 mm) (with supports collapsed).
WEIGHT: 400 lbs (181 kg).
SUPPORTING TOOLS: Overhead Hoist and Lift Sling, 2C6013.
TOOL MAINTENANCE: Coat treated surfaces (black oxide or black phosphate)
with corrosion preventive light oil when stored.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS LIST
GROUP PART NO. NOMENCLATURE QUANTITY SUPPLIER
NUMBER CODE
G07 2C6024P02 Base 1
2C6024P03 Yoke 2
2C6024P11 Hand Knob 2
2C6024P18 Spring Clip 2
2C6024P33 Support 2
BLS6GT19 Ball-Lok Pin 4 A
BLS8GT13 Ball-Lok Pin 4 A
LTI504-C4-6 Lanyard 8 A
S-MS-6D-4SL Caster 4 N
49001 Floor Lock 2 O
FOR ALL
2C6024G07
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C6024G07
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
TRUCK - COMPRESSOR ROTOR
2C6024G08
PURPOSE AND USE: To transport and store compressor rotor and also to pivot rotor
when changing from a horizontal to vertical position. The G08 was created without
forward lifting features for compatibility with CF6-80A, -80E1, and -80C2 engines.
DESCRIPTION: A welded stand with casters and floor locks. Both support rings pivot
so that the rotor can be lifted vertically from one of the two ends. Front and
rear supports collapse for clearance. The stand is to be pushed by hand.
DIMENSIONS: 41 x 75 x 12 in. (1,041 x 1,905 x 305 mm) (with supports collapsed).
WEIGHT: 400 lbs (181 kg).
SUPPORTING TOOLS: Overhead Hoist and Lift Sling, 2C6013,
2C6054, 2C6800, and 2C14014.
TOOL MAINTENANCE: Coat treated surfaces (black oxide or black phosphate)
with corrosion preventive light oil when stored.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS LIST
GROUP PART NO. NOMENCLATURE QUANTITY SUPPLIER
NUMBER CODE
G08 2C6024P02 Base 1
2C6024P03 Yoke 2
2C6024P11 Hand Knob 2
2C6024P18 Spring Clip 2
2C6024P33 Support 2
BLS6GT19 Ball-Lok Pin 4 A
BLS8GT13 Ball-Lok Pin 4 A
LTI504-C4-6 Lanyard 8 A
S-MS-6D-4SL Caster 4 N
49001 Floor Lock 2 O
FOR ALL
2C6024G08
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C6024G08
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FIXTURE, DISASSEMBLY - COMPRESSOR ROTOR
2C6029G05
FOR ALL
2C6029G05
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C6029G05
Page 2
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FIXTURE, LIFT - COMPRESSOR ROTOR SPOOLS
2C6031G02
PURPOSE AND USE: This fixture is used to lift vertically the stage 3-9 and 11-14
spools during assembly/disassembly of compressor rotor.
DESCRIPTION: Tool consists of a lift bar with adjustable lift fixtures
to fit the different size spools.
DIMENSIONS: 24 in. (610 mm) long.
WEIGHT: 10 lbs (4.5 kg).
SUPPORTING TOOLS: Hoist, fixed, or portable.
TOOL MAINTENANCE: Apply a light coat of oil to all surfaces when stored. Load test
periodically (see GE drawing 2C6031 for load test diagram and applicable NOTE).
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS LIST
GROUP PART NO. NOMENCLATURE QUANTITY SUPPLIER
NUMBER CODE
G02 2C6031P04 Hand Knob 2
2C6031P05 Shoulder Pin 2
2C6031P10 Arm 1
2C6031P11 Shoe 2
2C6031P12 Washer 2
SPW-2 Spherical Washer 2 C
FOR ALL
2C6031G02
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C6031G02
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
PLATFORM, MAINTENANCE - CORE ENGINE VERTICAL
2C6054G10
PURPOSE AND USE: The Maintenance Platform is used to assemble and disassemble
the core engine with or without the low pressure turbine unit.
DESCRIPTION: The Maintenance Platform consists of a circular support for
vertical installation of the core surrounded by a rectangular steel stand
for personnel. The primary color of the tool is blue. The G10 is now
obsolete and was superseded by the G13 version.
DIMENSIONS: 72 x 60 x 16 in. (1,829 x 1,524 x 406 mm).
WEIGHT: 2,000 lbs (907 kg).
SUPPORTING TOOLS: 2C6102, 2C6162.
TOOL MAINTENANCE: Coat unpainted and unplated surfaces with a corrosion preventive
compound (MIL-C-16173, Grade 3) or equivalent. Apply corrosion preventive
oil to all surfaces that have a black oxide finish.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing 2C6054.
FOR ALL
2C6054G10
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C6054G10
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
PLATFORM, MAINTENANCE - CORE ENGINE VERTICAL
2C6054G13
PURPOSE AND USE: The Maintenance Platform is used to assemble and disassemble
the core engine with or without the low pressure turbine unit.
DESCRIPTION: The Maintenance Platform consists of a circular support for vertical
installation of the core surrounded by a rectangular steel stand for personnel. The
primary color of the tool is blue. The G13 differs from the G10 in that a Teflon
bearing replaces the engine bearing, 4 adjustable supports add rigidity to the main
plate, the spline adapter is modified for correct rotor add seating, and the rotor
drive is modified for use with a key mounting instead of a pin mounting.
DIMENSIONS: 72 x 60 x 16 in. (1,829 x 1,524 x 406 mm).
WEIGHT: 2,000 lbs (907 kg).
SUPPORTING TOOLS: 2C6102, 2C6162.
TOOL MAINTENANCE: Coat unpainted and unplated surfaces with a corrosion preventive
compound (MIL-C-16173, Grade 3) or equivalent. Apply corrosion preventive
oil to all surfaces that have a black oxide finish.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing 2C6054.
FOR ALL
2C6054G13
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C6054G13
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
PROTECTOR, STAGE 1 FAN DISK BORE
2C6075G03
FOR ALL
2C6075G03
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C6075G03
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
PUSHER, INNER RACE - SPACER - AIR AND OIL SEAL - NO. 1 BEARING
2C6120G02
PURPOSE AND USE: To seat No. 1 bearing spacer, race, and seal on forward shaft.
DESCRIPTION: Consists of steel ring with two handles and an adjustable
brace which is screwed to the forward fan shaft.
DIMENSIONS: 14.5 in. dia x 12 in. (370 mm dia x 305 mm).
WEIGHT: 20 lbs (9 kg).
SUPPORTING TOOLS: None required.
TOOL MAINTENANCE: Treated surfaces (black oxide) to be coated with
corrosion preventive light oil when stored.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS LIST
GROUP PART NO. NOMENCLATURE QUANTITY SUPPLIER
NUMBER CODE
G02 2C6120P02 Ring 1
2C6120P03 Handle 1
2C6120P04 Brace 1
2C6120P11 Screw 2
31907 Flat Washer 2 F
FOR ALL
2C6120G02
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C6120G02
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FIXTURE, INSTALL AND REMOVE - BOLTS - FORWARD FAN SHAFT
2C6122G02
PURPOSE AND USE: To remove and install bolts from forward fan shaft.
DESCRIPTION: Consists of a Steel plate with hydraulic cylinder. A pusher
fits over the head of the fan shaft bolt.
DIMENSIONS: Pusher 6 in. (150 mm) wide, plate and adapter for hydraulic
cylinder 5 in. (125 mm) deep.
WEIGHT: 13 lbs (6 kg).
SUPPORTING TOOLS: Hand Operated Hydraulic Power Source.
TOOL MAINTENANCE: Treated surfaces (black oxide) to be coated with
corrosion preventive light oil when stored.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS LIST
GROUP PART NO. NOMENCLATURE QUANTITY SUPPLIER
NUMBER CODE
G02 2C6122P02 Foot 1
2C6122P03 Pusher 1
2C6122P19 Manifold 1
2C6122P20 Gage Protector 1
RC119 Hydraulic Cylinder 1 D
AR400 Coupler 1 D
FOR ALL
2C6122G02
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C6122G02
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FIXTURE, INSTALL AND REMOVE - BOLTS - FORWARD FAN SHAFT
2C6122G03
PURPOSE AND USE: To remove and install bolts from forward fan shaft.
DESCRIPTION: Consists of a steel plate with hydraulic cylinder. A pusher fits over
the head of the fan shaft bolt. This tool replaces an obsolete hydraulic cylinder
with one currently available. This also requires new pipe fittings.
DIMENSIONS: Pusher 6 in. (150 mm) wide, plate and adapter for hydraulic
cylinder 5 in. (125 mm) deep.
WEIGHT: 13 lbs (6 kg).
SUPPORTING TOOLS: Hand operated hydraulic power source.
TOOL MAINTENANCE: Treated surfaces (black oxide) to be coated with
corrosion preventive light oil when stored.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS LIST
GROUP PART NO. NOMENCLATURE QUANTITY SUPPLIER
NUMBER CODE
G03 2C6122P02 Foot 1
2C6122P03 Pusher 1
2C6122P19 Manifold 1
2C6122P20 Gage Protector 1
BCR-25 Hydraulic Cylinder 1 D
AR400 Coupler 1 D
FOR ALL
2C6122G03
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C6122G03
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
STAND, SHIPPING - ENGINE
2C6143G10
PURPOSE AND USE: The Shipping Stand is used to either store or ship
the engine without the nose cowl.
DESCRIPTION: The Shipping Stand is a large cradle with caster, brakes,
shocks, and a tow bar. Without the casters the stand can be moved by a
fork lift. The primary color of the tool is blue. The G10 version has
different instruction plates than the G11.
DIMENSIONS: 96 x 162 x 72 in. (2,438 x 4,115 x 1,829 mm).
WEIGHT: 4,800 lbs (2,179 kg).
SUPPORTING TOOLS: 2C6126.
TOOL MAINTENANCE: TBD
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing 2C6143.
FOR ALL
2C6143G10
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C6143G10
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
STAND, SHIPPING - ENGINE
2C6143G11
PURPOSE AND USE: The Shipping Stand is used to either store or ship
the engine without the nose cowl.
DESCRIPTION: The Shipping Stand is a large cradle with caster, brakes,
shocks, and a tow bar. Without the casters the stand can be moved by a
fork lift. The primary color of the tool is blue. The G11 version has
different instruction plates than the G10.
DIMENSIONS: 96 x 162 x 72 in. (2,438 x 4,115 x 1,829 mm).
WEIGHT: 4,800 lbs (2,179 kg).
SUPPORTING TOOLS: 2C6126.
TOOL MAINTENANCE: TBD
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing 2C6143.
FOR ALL
2C6143G11
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C6143G11
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
PLATFORM, REMOVAL - VERTICAL - COMPRESSOR STATOR CASE
2C6162G04
FOR ALL
2C6162G04
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C6162G04
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
TOOL SET, JACKSCREW
2C6164G01
PURPOSE AND USE: To remove parts from engine where jackscrews are required.
DESCRIPTION: Set of various sized jackscrews stored in a container.
DIMENSIONS: 9 x 7 x 2 in (229 x 178 x 51 mm).
WEIGHT: 5 lb (23 kg).
SUPPORTING TOOLS: 0.375 in. (9.5 mm) wrench.
TOOL MAINTENANCE: Coat black oxided surfaces with light oil.
QUANTITY PER OPERATION: One set.
REPLACEMENT PARTS LIST
GROUP PART NO. NOMENCLATURE QUANTITY SUPPLIER
NUMBER CODE
G01 2C6164P02 Tool Box 1
2C6164P03 Jackscrew 4
2C6164P04 Jackscrew 4
2C6164P05 Jackscrew 4
2C6164P06 Jackscrew 4
FOR ALL
2C6164G01
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C6164G01
Page 2
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
SLING, FRAMES - LIFTING AND CLEANING, VERTICAL
2C6168G02
PURPOSE AND USE: To lift compressor rear frame, low pressure turbine stator
halves, turbine rear frame, and midframe.
DESCRIPTION: Consists of lift eye and three cables with brackets to secure
the tool to the aft flanges of the frames.
DIMENSIONS: 33 in. (840 mm) long.
WEIGHT: 8 lbs (4 kg).
SUPPORTING TOOLS: Hoist, fixed or portable.
TOOL MAINTENANCE: Load test periodically (see GE drawing 2C6168 for
load test diagram and applicable NOTE).
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS LIST
GROUP PART NO. NOMENCLATURE QUANTITY SUPPLIER
NUMBER CODE
G02 2C6168P04 Button 3
2C6168P05 Pin 3
2C6168P06 Inseparable Assembly 1
2C6168P09 Lifting Hook 3
2C6168P10 Clamp 3
D9-625 Dowel Pin SST 3 M
FOR ALL
2C6168G02
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C6168G02
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
PINS, GUIDE - BEARINGS, INSTALLATION
2C6170G02
FOR ALL
2C6170G02
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C6170G02
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
HOLDER SET, VARIABLE STATOR VANES
2C6171G02
PURPOSE AND USE: To hold compressor forward stator variable vanes while installing
nuts. This tool is obsolete and was superseded by tool 2C14866G02.
DESCRIPTION: Plastic half-circle.
DIMENSIONS: 16 x 32 x 10 in. (405 x 815 x 255 mm).
WEIGHT: 75 lbs (34 kg).
SUPPORTING TOOLS: Standard hand tools.
TOOL MAINTENANCE: None required.
QUANTITY PER OPERATION: One set.
REPLACEMENT PARTS LIST
GROUP PART NO. NOMENCLATURE QUANTITY SUPPLIER
NUMBER CODE
G02 2C6171P02 Holder, Stage IGV 1
2C6171P03 Holder, Stage 1 1
2C6171P04 Holder, Stage 2 1
2C6171P05 Holder, Stage 3 1
2C6171P06 Holder, Stage 4 1
2C6171P07 Holder, Stage 5 1
FOR ALL
2C6171G02
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C6171G02
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
CONTAINER, SHIPPING - FAN MID/FORWARD SHAFT
2C6176G03
PURPOSE AND USE: To contain and cover the fan mid shaft or the fan forward shaft
during transportation and storage. Container to be moved by fork lift truck.
DESCRIPTION: Welded metal skid with cover.
DIMENSIONS: 144 x 24 x 19 in. (3,658 x 610 x 483 mm).
WEIGHT: 370 lbs (168 kg).
SUPPORTING TOOLS: None.
TOOL MAINTENANCE: Protect metal surfaces not painted or plated with corrosion
preventive compound (Kendex 7003, Kendall Oil Co., Bradford, PA) or equivalent.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS LIST
GROUP PART NO. NOMENCLATURE QUANTITY SUPPLIER
NUMBER CODE
G03 2C6176P03 Special Eye Nut 1
2C6176P05 Block Vee 1
2C6176P06 Clamp 1
2C6176P07 Rubber Pad 1
2C6176P08 Sleeve 1
2C6176P09 Lid 1
2C6176P10 Spacer 1
2C6176P11 Block 1
2C6176P32 Base 1
Spacer 1
2C6176P34
21FKF-420 Self-Locking Nut 1 AK
21FKF-518 Self-Locking Nut 1 AK
31FKF-1011 Self-Locking Nut 1 AK
FOR ALL
2C6176G03
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C6176G03
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
DELETED
2C6178G10
PURPOSE AND USE: This tool has been deleted in its entirety.
FOR ALL
2C6178G10
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FIXTURE SET, POSITION - VARIABLE STATOR VANES
2C6178G11
PURPOSE AND USE: The Position Fixture Set is used to preset the stator
vanes IGV thru stage 6 at the proper angle prior to grinding the stator
vane tips to required diameters.
DESCRIPTION: The Position Fixture Set consists of locating plates with
nuts and clamps to position stator vanes.
DIMENSIONS: 8 x 4 x 4 in. (203 x 102 x 102 mm).
WEIGHT: 5 lbs (2 kg).
SUPPORTING TOOLS: TBD
TOOL MAINTENANCE: Apply corrosion preventive oil to all surfaces that
have black oxide or black phosphate coating.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing 2C6178.
FOR FADEC
2C6178G11
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR FADEC
2C6178G11
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
DELETED
2C6178G12
PURPOSE AND USE: This tool has been deleted in its entirety.
FOR ALL
2C6178G12
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FIXTURE SET, POSITION - VARIABLE STATOR VANES
2C6178G13
PURPOSE AND USE: The Position Fixture Set is used to preset the stator
vanes IGV thru stage 5 at the proper angle prior to grinding the stator
vane tips to required diameters.
DESCRIPTION: The Position Fixture Set consists of locating plates with
nuts and clamps to position stator vanes. This tool is only applicable to
CF6-80C2 FADEC engines that are Post SB 72-1081.
DIMENSIONS: 8 x 4 x 4 in. (203 x 102 x 102 mm).
WEIGHT: 5 lbs (2 kg).
SUPPORTING TOOLS: TBD
TOOL MAINTENANCE: Apply corrosion preventive oil to all surfaces that
have black oxide or black phosphate coating.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing 2C6178.
FOR FADEC
2C6178G13
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR FADEC
2C6178G13
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FIXTURE, INSPECTION - FAN MID AND FAN ROTOR FORWARD SHAFTS
2C6179G05
PURPOSE AND USE: To determine the eccentricity runout of the No. 1 bearing
land while supporting the assembled shafts.
DESCRIPTION: Three pedestals, two of which support the shafts. The third contains a
dial indicator for measurement purposes. Pedestals are to be floor mounted.
DIMENSIONS: 30 x 9 x 25 in. (762 x 229 x 635 mm).
WEIGHT: 55 lbs (25 kg).
SUPPORTING TOOLS: None.
TOOL MAINTENANCE: Coat treated surfaces (black oxide or black phosphate)
with corrosion preventive light oil.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS LIST
GROUP PART NO. NOMENCLATURE QUANTITY SUPPLIER
NUMBER CODE
G05 2C6179P19 Upright Assembly - 1
Forward
2C6179P03 Upright Assembly - Mid 1
2C6179P23 Upright Assembly - Aft 1
2C6179P20 Bracket Assembly 1
2C6179P06 Pin, Headless 4
2C6179P08 Pin, Shouldered 2
CYR-17/8-S Cam Follower Bearing 6 BX
LC-067J-5 Spring 2 L
2C6179P30 End Stop 1
2C6179P25 Roller Block 1
No. 746A Test Set 1 AV
FOR ALL
2C6179G05
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C6179G05
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FIXTURE, LIFT - ENGINE TURNOVER, TURBINE REAR FRAME
2C6211G05
PURPOSE AND USE: To support and turn engine from horizontal to vertical position.
DESCRIPTION: A mounting ring with a pivoting lift bracket.
DIMENSIONS: 4 ft (1,219 mm) dia x 13 in. (330 mm).
WEIGHT: 260 lbs (118kg).
SUPPORTING TOOLS: 2C6182 Lift Fixture; overhead hoist, fixed or portable.
TOOL MAINTENANCE: Load test periodically (see GE drawing 2C6211 for
load test diagram and applicable NOTE). Protect surfaces not painted
or plated with a corrosive preventive compound (Kendex 7003, Kendall
Oil Co., Bradford, PA) or equivalent.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS LIST
GROUP PART NO. NOMENCLATURE QUANTITY SUPPLIER
NUMBER CODE
G05 2C6211P03 Lift Bracket 1
2C6211P05 Rest Pad 4
2C6211P27 Mounting Ring 1
2C6211P28 Clevis 2
4 Ton Size Eye Bolt 1 AS
BLS12LA22S Ball-Lok Pin 2 Q
L-10-T6-V Lanyard 2 Q
FOR ALL
2C6211G05
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C6211G05
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FIXTURE, LIFT - LOW PRESSURE TURBINE AND HIGH PRESSURE TURBINE ROTOR DISK
2C6238G04
PURPOSE AND USE: The Lift Fixture is used to lift the low pressure turbine (LPT) and
high pressure turbine (HPT) rotor disk during engine buildup or disassembly.
DESCRIPTION: The Lift Fixture consists of a three-legged sling with end fittings and
ball lock attachment pins. The tool has a black oxide or black phosphate finish.
DIMENSIONS: 22 in. (559 mm).
WEIGHT: 12 lb (5 kg).
SUPPORTING TOOLS: 1000 lb (454 kg) Hoist.
TOOL MAINTENANCE: Apply corrosion preventive oil to all surfaces that
have black oxide or black phosphate coating.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing 2C6238.
FOR ALL
2C6238G04
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C6238G04
Page 2
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FIXTURE SET, SECURE - VARIABLE STATOR ARMS, STAGE 3-6
2C6259G05
FOR ALL
2C6259G05
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C6259G05
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
WRENCH, SPANNER NUT - NO. 1 BEARING
2C6265G02
PURPOSE AND USE: To remove and install No. 1 bearing spanner nut.
DESCRIPTION: Circular steel plate with tube attachment and
provision for torque multiplier.
DIMENSIONS: 15 in. dia x 13 in. (380 mm dia x 330 mm).
WEIGHT: 45 lb (20.4 kg).
SUPPORTING TOOLS: Torque Multiplier, Sweeney Model 8100 (Supplier
Code B) or equivalent.
TOOL MAINTENANCE: Coat treated surfaces (black oxide) with
preventive light oil when stored.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS LIST
GROUP PART NO. NOMENCLATURE QUANTITY SUPPLIER
NUMBER CODE
G02 2C6265P05 Screw 5
2C6265P06 Hand Knob 1
2C6265P07 Retaining Ring 1
2C6265P12 Spacer 2
2C6265P14 Antitorque Bar 1
2C6265P15 Locating Assembly 1
2C6265P16 Spline Assembly 1
FOR ALL
2C6265G02
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C6265G02
Page 2
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
SCALE, SOURCE - MOMENT WEIGHT BLADES
2C6333
PURPOSE AND USE: To measure the moment weight of engine fan blades.
DESCRIPTION: A source drawing with critical blade dimensions for references.
DIMENSIONS: N/A
WEIGHT: N/A
SUPPORTING TOOLS: Adapters and counterweights as required.
TOOL MAINTENANCE: See vendor literature.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: N/A
FOR ALL
2C6333
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C6333
Page 2
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
SUPPORT - ENGINE HANDLING
2C6339G05
PURPOSE AND USE: The Support is used with various engine adapter brackets to
support the engine during maintenance operations and storage.
DESCRIPTION: The Support consists of a base pedestal with an adjustable screwjack
clevis post. The primary color of the tool is blue.
DIMENSIONS: 60 x 26 in. (1,524 x 660 mm).
WEIGHT: 183 lbs (83 kg).
SUPPORTING TOOLS: Pedestal adapters 2C14726G03 (non-FADEC) or 2C14726G05 (FADEC).
TOOL MAINTENANCE: Apply corrosion preventive oil to all surfaces that
have black oxide or black phosphate coating.
QUANTITY PER OPERATION: Four per engine.
REPLACEMENT PARTS: Refer to drawing 2C6339.
FOR ALL
2C6339G05
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C6339G05
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
SUPPORT - ENGINE HANDLING
2C6339G06
PURPOSE AND USE: The Support is used with various engine adapter brackets to
support the engine during maintenance operations and storage.
DESCRIPTION: The Support consists of a base pedestal with an adjustable screwjack
clevis post. The primary color of the tool is blue.
DIMENSIONS: 60 x 26 in. (1,524 x 660 mm).
WEIGHT: 183 lbs (83 kg).
SUPPORTING TOOLS: Pedestal adapters 2C14730G01, 2C14726G03 (non-FADEC) or 2C14726G05
(FADEC), CRF adapter 2C14780G02, and TRF adapter 2C14827G01.
TOOL MAINTENANCE: Apply corrosion preventive oil to all surfaces that
have black oxide or black phosphate coating.
QUANTITY PER OPERATION: Four per engine.
REPLACEMENT PARTS: Refer to drawing 2C6339.
FOR ALL
2C6339G06
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C6339G06
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
WRENCH, SPLINE - DIRECT DRIVE
2C6341G02
FOR ALL
2C6341G02
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C6341G02
Page 2
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
STAND, ASSEMBLY - ENGINE VERTICAL
2C6344G02
FOR ALL
2C6344G02
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C6344G02
Page 2
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
PIN, GUIDE - FAN ROTOR INSTALLATION
2C6348P02
PURPOSE AND USE: To guide fan onto fan forward shaft during installation.
DESCRIPTION: Tapered pin with head.
DIMENSIONS: 1.2 in. dia x 6.6 in. long (31 mm dia x 168 mm long).
WEIGHT: 1 lb (0.5 kg).
SUPPORTING TOOLS: None required.
TOOL MAINTENANCE: None required.
QUANTITY PER OPERATION: Three.
REPLACEMENT PARTS: Not applicable.
FOR ALL
2C6348P02
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C6348P02
Page 2
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FIXTURE, LIFT - FAN FRAME, AFT
2C6350G03
FOR ALL
2C6350G03
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C6350G03
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FIXTURE, LIFT - FAN FRAME, AFT
2C6350G04
FOR ALL
2C6350G04
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C6350G04
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
WRENCH SET, SPANNER - AIRTUBE NUTS
2C6352G06
PURPOSE AND USE: The Spanner Wrench Set is used to tighten and remove airtube nuts.
DESCRIPTION: The Spanner Wrench Set consists of spanner wrenches with
square drive and spanner wrench extension. This tool is obsolete and
was superseded by tool 2C14856G01.
DIMENSIONS: 10 x 10 x 14 in. (254 x 254 x 356 mm).
WEIGHT: 10 lbs (5 kg).
SUPPORTING TOOLS: 1/2 in. Square Drive, 10-200 lbs in. (1.1-22.6
N.m) Torque Wrench.
TOOL MAINTENANCE: None.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing 2C6352.
FOR ALL
2C6352G06
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C6352G06
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
WRENCH SET, SPANNER - AIRTUBE NUTS
2C6352G07
PURPOSE AND USE: The Spanner Wrench Set is used to tighten and remove airtube nuts.
DESCRIPTION: The Spanner Wrench Set consists of spanner wrenches with
square drive and spanner wrench extension. The spanner wrench set 2C6352G07
supersedes the G06 version and uses P24 and P25 spanners that work with part
number 1507M32 airtube retaining nuts. The 2C6352G07 tool was superseded by
spanner wrench set, 2C14856G01, which was designed for use with reinforced
tube end fittings introduced by SB 75-0040, SB 75-0072, SB 75-0077 thru SB
75-0079, SB 75-0081 thru SB 75-0089, and SB 75-0091.
DIMENSIONS: 10 x 10 x 14 in. (254 x 254 x 356 mm).
WEIGHT: 10 lbs (5 kg).
SUPPORTING TOOLS: 1/2 in. Square Drive, 10-200 lbs in. (1.1-22.6
N·m) Torque Wrench.
TOOL MAINTENANCE: None.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing 2C6352.
FOR ALL
2C6352G07
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C6352G07
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
DELETED
2C6353G02
PURPOSE AND USE: This tool has been deleted in its entirety.
FOR ALL
2C6353G02
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
ADAPTERS, PEDESTAL - FAN MIDSHAFT
2C6363G01
FOR ALL
2C6363G01
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C6363G01
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
TOOL, INSTALL/REMOVE - PIN - FAN REVERSER ACTUATOR
2C6367G01
PURPOSE AND USE: To install and remove fan reverser actuator rod pin.
DESCRIPTION: An impact tool with a threaded end to engage the headless straight pin.
DIMENSIONS: 2 in. diameter x 15 in. long (51 mm dia x 381 mm long).
WEIGHT: 12 lb (5.5 kg).
SUPPORTING TOOLS: None.
TOOL MAINTENANCE: Coat treated surfaces (black oxide) with corrosion
preventive light oil when stored.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Inseparable assembly.
FOR ALL
2C6367G01
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C6367G01
Page 2
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
HEATER, CASE - AFT FAN
2C6372G01
PURPOSE AND USE: To heat fan case so that fan frame can be slipped into fan case.
DESCRIPTION: A hand cart with cables and flexible heater elements. The six
heater elements measure 4.5 x 44 in. (114 x 1,118 mm).
DIMENSIONS: 39 x 24 x 32 in. (990 x 610 x 810 mm).
WEIGHT: 325 lbs (148 kg).
SUPPORTING TOOLS: None required.
TOOL MAINTENANCE: None required.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS LIST
GROUP PART NO. NOMENCLATURE QUANTITY SUPPLIER
NUMBER CODE
G01 2C6372P02 Truck 1
2C6372P03 Electric Cord 6
9422M18P01 Heater 6 AL
9422M19P0l Power Center 1 AL
CGB-599 Connector 1 AM
9361 Plug Connector 1 AN
FOR ALL
2C6372G01
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C6372G01
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
HEATER, CASE - AFT FAN
2C6372G02
PURPOSE AND USE: To heat fan case so that fan frame can be slipped into fan case.
DESCRIPTION: A hand cart with cables and flexible heater elements. The six
heater elements measure 4.5 x 44 in. (114 x 1,118 mm).
DIMENSIONS: 39 x 24 x 32 in. (990 x 610 x 810 mm).
WEIGHT: 325 lbs (148 kg).
SUPPORTING TOOLS: None required.
TOOL MAINTENANCE: None required.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS LIST
GROUP PART NO. NOMENCLATURE QUANTITY SUPPLIER
NUMBER CODE
G02 2C6372P03 Electric Cord 6
2C6372P17 Truck 1
2C6372P20 Transformer 1
2C6372P21 Power Center 1
9422M18P01 Heater 6 AL
9T21B1055G02 General Transformer 1 AM
CGB-599 Connector 1 AM
9368 Plug Connector 1 AN
FOR ALL
2C6372G02
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C6372G02
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
HEATER, CASE - AFT FAN
2C6372G03
PURPOSE AND USE: To heat fan case so that fan frame can be slipped into fan case.
DESCRIPTION: A hand cart with cables and flexible heater elements. The
six heater elements measure 4.5 x 44 in. (114 x 1,118 mm). This tool
requires power of 115V 50/60 Hz.
DIMENSIONS: 39 x 24 x 32 in. (990 x 610 x 810 mm).
WEIGHT: 325 lbs (148 kg).
SUPPORTING TOOLS: None required.
TOOL MAINTENANCE: None required.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS LIST
GROUP PART NO. NOMENCLATURE QUANTITY SUPPLIER
NUMBER CODE
G03 2C6372P32 Truck 1
2C6372P03 Electric Cord 6
9422M18P01 Heater 6 AL
2C6372P33 Power Center 1
CGB-599 Connector 1 AM
9361 Plug Connector 1 AN
HBL4700 Receptacle (110V) 3 AN
FOR ALL
2C6372G03
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C6372G03
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
HEATER, CASE - AFT FAN
2C6372G04
PURPOSE AND USE: To heat fan case so that fan frame can be slipped into fan case.
DESCRIPTION: A hand cart with cables and flexible heater elements. The
six heater elements measure 4.5 x 44 in. (114 x 1,118 mm). This tool
requires power of 230V 50/60 Hz.
DIMENSIONS: 39 x 24 x 32 in. (990 x 610 x 810 mm).
WEIGHT: 325 lbs (148 kg).
SUPPORTING TOOLS: None required.
TOOL MAINTENANCE: None required.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS LIST
GROUP PART NO. NOMENCLATURE QUANTITY SUPPLIER
NUMBER CODE
G04 2C6372P32 Truck 1
2C6372P42 Electric Cord 6
9422M18P02 Heater 6
2C6372P33 Power Center 1
CGB-599 Connector 1 AM
9368 Plug Connector 1 AN
HBL4550 Receptacle (220V) 3 AN
FOR ALL
2C6372G04
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C6372G04
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FIXTURE, LIFT - FAN FORWARD SHAFT
2C6376G02
PURPOSE AND USE: To lift and transport the forward fan shaft after
removal from the fan maintenance unit.
DESCRIPTION: An attaching pad arrangement with adjustable lift bar so that the
forward fan shaft can be handled at the forward flange of the shaft.
DIMENSIONS: 20 x 20 in. (508 x 508 mm).
WEIGHT: 10 lbs (4.5 kg).
SUPPORTING TOOLS: Overhead hoist.
TOOL MAINTENANCE: Treated surfaces (black oxide) to be coated with corrosion
preventive light oil when stored. Load test periodically (see GE drawing
2C6376 for load test diagram and applicable NOTE).
QUANTITY PER OPERATION:
REPLACEMENT PARTS LIST
GROUP PART NO. NOMENCLATURE QUANTITY SUPPLIER
NUMBER CODE
G02 2C6376P07 Pad 2
2C6376P14 Lift Bar 1
2C6376P15 Support 1
CL-1-HK2T Hand Knob 1 I
FOR ALL
2C6376G02
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C6376G02
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
BORESCOPE SET, FIBER LIGHT
2C6388G06
PURPOSE AND USE: The Fiber Light Borescope Set is used to make an inspection
of the internal engine parts without engine disassembly.
DESCRIPTION: The Fiber Light Borescope Set is an optical instrument with a light
source that will permit a periscopical view of internal engine parts.
DIMENSIONS: 20 x 20 x 8 in. (508 x 508 x 203 mm).
WEIGHT: 50 lb (23 kg).
SUPPORTING TOOLS: 35mm camera and adapter or Polaroid camera and adapter.
TOOL MAINTENANCE: See vendor literature.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing 2C6388.
FOR ALL
2C6388G06
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C6388G06
Page 2
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
ACTUATOR, INLET GUIDE VANE - HYDRAULIC
2C6395G05
PURPOSE AND USE: To supply operating pressure for static rigging of VSV/ VBV system.
DESCRIPTION: The unit is self-contained with a reservoir, hand pump,
gages, shutoff check and pressure relief valves, and connecting hoses, has
guard rails which serve as carrying handles.
DIMENSIONS: 10 x 17 x 8 in. (254 x 432 x 203 mm).
WEIGHT: 40 lb (18 kg).
SUPPORTING TOOLS: To be supplied.
TOOL MAINTENANCE: Maintain fluid level in tank.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: This actuator has an extensive parts list that will be of
little value without the drawings. Refer to GE Drawing, 2C6395.
FOR ALL
2C6395G05
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C6395G05
Page 2
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
SET, TRANSMITTER - VSV POSITION
2C6451G03
FOR ALL
2C6451G03
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C6451G03
Page 2
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
DELETED
2C6456P03
PURPOSE AND USE: This tool has been deleted in its entirety.
FOR ALL
2C6456P03
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
ADAPTER, TEST - COMPRESSOR DISCHARGE PRESSURE (PS3)
2C6456P04
PURPOSE AND USE: The Test Adapter is used to connect the instrumentation used
for measuring compressor discharge pressure during the engine test.
DESCRIPTION: The Test Adapter is a modified fitting with a hole through the length.
DIMENSIONS: 2 x 3 x 4 in. (102 x 76 x 102 mm).
WEIGHT: 8 oz. (227 grams).
SUPPORTING TOOLS: Engine test equipment.
TOOL MAINTENANCE: None.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing 2C6456.
FOR ALL
2C6456P04
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C6456P04
Page 2
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
PROBE, TEMPERATURE - OIL SUPPLY AND SCAVENGE
2C6458G09
PURPOSE AND USE: The Temperature Probe is used to measure supply oil and
scavenge oil temperature during engine test.
DESCRIPTION: The Temperature Probe is a thermocouple with a pipe plug and electrical
plug. It is copper/constantan and used for scavenge temperature.
DIMENSIONS: 4 x 3 x 2 in. (102 x 76 x 51 mm).
WEIGHT: 0.25 lb (0.1 kg).
SUPPORTING TOOLS: Grounded Cable, Digital Meter or Constant
Temperature Reference Junction.
TOOL MAINTENANCE: None.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing 2C6458.
FOR ALL
2C6458G09
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C6458G09
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
PROBE, TEMPERATURE - OIL SUPPLY AND SCAVENGE
2C6458G10
PURPOSE AND USE: The Temperature Probe is used to measure supply oil and
scavenge oil temperature during engine test.
DESCRIPTION: The Temperature Probe is a thermocouple with a pipe plug and electrical
plug. It is iron/constantan and used for scavenge temperature.
DIMENSIONS: 4 x 3 x 2 in. (102 x 76 x 51 mm).
WEIGHT: 0.25 lb (0.1 kg).
SUPPORTING TOOLS: Grounded Cable, Digital Meter or Constant
Temperature Reference Junction.
TOOL MAINTENANCE: None.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing 2C6458.
FOR ALL
2C6458G10
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C6458G10
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
PROBE, TEMPERATURE - OIL SUPPLY AND SCAVENGE
2C6458G11
PURPOSE AND USE: The Temperature Probe is used to measure supply oil and
scavenge oil temperature during engine test.
DESCRIPTION: The Temperature Probe is a thermocouple with a pipe plug and electrical
plug. It is chromel/alumel and used for scavenge temperature.
DIMENSIONS: 4 x 3 x 2 in. (102 x 76 x 51 mm).
WEIGHT: 0.25 lb (0.1 kg).
SUPPORTING TOOLS: Grounded Cable, Digital Meter or Constant
Temperature Reference Junction.
TOOL MAINTENANCE: None.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing 2C6458.
FOR ALL
2C6458G11
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C6458G11
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
PROBE, TEMPERATURE - OIL SUPPLY AND SCAVENGE
2C6458G12
PURPOSE AND USE: The Temperature Probe is used to measure supply oil and
scavenge oil temperature during engine test.
DESCRIPTION: The Temperature Probe is a thermocouple with a pipe plug and electrical
plug. It is chromel/constantan and used for scavenge temperature.
DIMENSIONS: 4 x 3 x 2 in. (102 x 76 x 51 mm).
WEIGHT: 0.25 lb (0.1 kg).
SUPPORTING TOOLS: Grounded Cable, Digital Meter or Constant
Temperature Reference Junction.
TOOL MAINTENANCE: None.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing 2C6458.
FOR ALL
2C6458G12
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C6458G12
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
PROBE, TEMPERATURE - OIL SUPPLY AND SCAVENGE
2C6458G13
PURPOSE AND USE: The Temperature Probe is used to measure supply oil and
scavenge oil temperature during engine test.
DESCRIPTION: The Temperature Probe is a thermocouple with a pipe plug and
electrical plug. It is copper/constantan and used for supply.
DIMENSIONS: 4 x 3 x 2 in. (102 x 76 x 51 mm).
WEIGHT: 0.25 lb (0.1 kg).
SUPPORTING TOOLS: Grounded Cable, Digital Meter or Constant
Temperature Reference Junction.
TOOL MAINTENANCE: None.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing 2C6458.
FOR ALL
2C6458G13
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C6458G13
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
PROBE, TEMPERATURE - OIL SUPPLY AND SCAVENGE
2C6458G14
PURPOSE AND USE: The Temperature Probe is used to measure supply oil and
scavenge oil temperature during engine test.
DESCRIPTION: The Temperature Probe is a thermocouple with a pipe plug and
electrical plug. It is iron/constantan and used for supply.
DIMENSIONS: 4 x 3 x 2 in. (102 x 76 x 51 mm).
WEIGHT: 0.25 lb (0.1 kg).
SUPPORTING TOOLS: Grounded Cable, Digital Meter or Constant
Temperature Reference Junction.
TOOL MAINTENANCE: None.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing 2C6458.
FOR ALL
2C6458G14
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C6458G14
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
PROBE, TEMPERATURE - OIL SUPPLY AND SCAVENGE
2C6458G15
PURPOSE AND USE: The Temperature Probe is used to measure supply oil and
scavenge oil temperature during engine test.
DESCRIPTION: The Temperature Probe is a thermocouple with a pipe plug and
electrical plug. It is chromel/alumel and used for supply.
DIMENSIONS: 4 x 3 x 2 in. (102 x 76 x 51 mm).
WEIGHT: 0.25 lb (0.1 kg).
SUPPORTING TOOLS: Grounded Cable, Digital Meter or Constant
Temperature Reference Junction.
TOOL MAINTENANCE: None.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing 2C6458.
FOR ALL
2C6458G15
Page 1
Dec 10/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C6458G15
Page 2
Dec 10/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
PROBE, TEMPERATURE - OIL SUPPLY AND SCAVENGE
2C6458G16
PURPOSE AND USE: The Temperature Probe is used to measure supply oil and
scavenge oil temperature during engine test.
DESCRIPTION: The Temperature Probe is a thermocouple with a pipe plug and
electrical plug. It is chromel/constantan and used for supply.
DIMENSIONS: 4 x 3 x 2 in. (102 x 76 x 51 mm).
WEIGHT: 0.25 lb (0.1 kg).
SUPPORTING TOOLS: Grounded Cable, Digital Meter or Constant
Temperature Reference Junction.
TOOL MAINTENANCE: None.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing 2C6458.
FOR ALL
2C6458G16
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C6458G16
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
DELETED
2C6459G09
PURPOSE AND USE: This tool has been deleted in its entirety.
FOR ALL
2C6459G09
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
DELETED
2C6459G10
PURPOSE AND USE: This tool has been deleted in its entirety.
FOR ALL
2C6459G10
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
PROTRACTOR, ELECTRONIC - VARIABLE STATOR VANE, PORTABLE
2C6459G11
FOR ALL
2C6459G11
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C6459G11
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
PROTRACTOR, ELECTRONIC - VARIABLE STATOR VANE, PORTABLE
2C6459G12
FOR ALL
2C6459G12
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C6459G12
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
BORESCOPE SET, FLYAWAY
2C6472G02
PURPOSE AND USE: The Flyaway Borescope Set is used to help make a fly or not fly
decision at a remote location by providing limited borescope inspection capability.
DESCRIPTION: The Flyaway Borescope Set consists of a light projector,
fiberlight cable, and borescope probe.
DIMENSIONS: Container, 20 x 16 x 9 in. (508 x 406 x 229 mm).
WEIGHT: 26 lb (12 kg).
SUPPORTING TOOLS: None.
TOOL MAINTENANCE: TBD
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing 2C6472.
FOR ALL
2C6472G02
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C6472G02
Page 2
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
SET, TRANSMITTER AND INDICATOR - VARIABLE STATOR VANE POSITION (B ANGLE) N2 CORE
SPEED
2C6483G01
PURPOSE AND USE: The Transmitter and Indicator Set is used to track
the variable stator vane position (B angle) and core speed (N2)
independent of the aircraft wiring.
DESCRIPTION: The Transmitter and Indicator Set is self-contained in a portable
aluminum carrying case along with its cables and a displacement transducer.
DIMENSIONS: Container, 21 x 17 x 8 in. (533 x 432 x 203 mm).
WEIGHT: 25 lb (11 kg).
SUPPORTING TOOLS: None.
TOOL MAINTENANCE: TBD
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing 2C6483.
FOR ALL
2C6483G01
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C6483G01
Page 2
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
TESTER, LUBE JET FLOW
2C6486G02
PURPOSE AND USE: The Lube Jet Flow Tester is used to check for plugged
or restricted oil jets on the engine.
DESCRIPTION: This Lube Jet Flow Tester consists of two pressure gates, an orifice,
a regulator filter, a relief valve and other hoses and adapter fittings.
DIMENSIONS: 14 x 7 x 4 in. (356 x 178 x 102 mm).
WEIGHT: 10 lb (5 kg).
SUPPORTING TOOLS: Shop air or nitrogen.
TOOL MAINTENANCE: Periodically check and calibrate according
to user quality control.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing 2C6486.
FOR ALL
2C6486G02
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C6486G02
Page 2
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
DELETED
2C6487G01
PURPOSE AND USE: This tool has been deleted in its entirety.
Superseded by tool 2C6487G05.
FOR ALL
2C6487G01
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
DELETED
2C6487G02
PURPOSE AND USE: This tool has been deleted in its entirety.
Superseded by tool 2C6487G05.
FOR ALL
2C6487G02
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
PROTRACTOR, ELECTRONIC - PORTABLE VARIABLE STATOR VANE
2C6487G05
PURPOSE AND USE: The Electronic Protractor is used to measure the variable
stator vane angles four channel unit.
DESCRIPTION: The Electronic Protractor consists of four encoders, one protractor
and a set master. The tool set is contained in one portable container. The
tool has a black oxide or black phosphate finish.
DIMENSIONS: Container, 26 x 18 x 10 in. (660 x 457 x 254 mm).
WEIGHT: 75 lbs (34 kg).
SUPPORTING TOOLS: 2C6395 or equivalent.
TOOL MAINTENANCE: Do an inspection and check the calibration of the tool
periodically. Refer to drawing 2C6487. Apply corrosion preventive oil to all
surfaces that have black oxide or black phosphate coating.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing 2C6487.
FOR ALL
2C6487G05
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C6487G05
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
PROTRACTOR, ELECTRONIC - PORTABLE VARIABLE STATOR VANE
2C6487G06
PURPOSE AND USE: The Electronic Protractor is used to measure the variable
stator vane angles four channel unit.
DESCRIPTION: The Electronic Protractor consists of four encoders, one protractor
and a set master. The tool set is contained in one portable container. The
tool has a black oxide or black phosphate finish.
DIMENSIONS: Container, 34 x 26 x 19 in. (864 x 660 x 482 mm).
WEIGHT: 99 lbs (45 kg).
SUPPORTING TOOLS: 2C6395 or equivalent.
TOOL MAINTENANCE: Do an inspection and check the calibration of the tool
periodically. Refer to drawing 2C6487. Apply corrosion preventive oil to all
surfaces that have black oxide or black phosphate coating.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing 2C6487.
FOR ALL
2C6487G06
Page 1
Dec 01/2016
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C6487G06
Page 2
Dec 01/2016
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
SNUBBER SET, TIP GRINDING - COMPRESSOR ROTOR
2C6510G01
FOR ALL
2C6510G01
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C6510G01
Page 2
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
JACK SET, ADJUSTING - T/R TRANSLATING COWL
2C6512G02
FOR ALL
2C6512G02
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C6512G02
Page 2
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
KIT, REFACING - INTERNAL FITTINGS, 37° ANGLE
2C6525G01
PURPOSE AND USE: To reface the 37° angle of "AN" internal fittings,
sizes -3, -4, -5, -6, -8 and -10.
DESCRIPTION: This tool consists of a set of cutters used with
a crank or a drill press.
DIMENSIONS: 12 x 6 x 4 in. (305 x 152 x 102 mm) deep.
WEIGHT: (To be furnished.)
SUPPORTING TOOLS: Drill press.
TOOL MAINTENANCE: Coat black oxide surfaces with a light coating of oil.
QUANTITY PER OPERATION: One set.
REPLACEMENT PARTS: See GE drawing 2C6525.
FOR ALL
2C6525G01
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C6525G01
Page 2
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
KIT, REFACING - SPHERICAL FITTINGS, EXTERNAL
2C6527G03
FOR ALL
2C6527G03
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C6527G03
Page 2
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
SNUBBER SET, GRINDING - COMPRESSOR STATOR VANES
2C6529G05
PURPOSE AND USE: To hold the stage 3 stator vanes to prevent vibration
during final length grinding operation.
DESCRIPTION: Curved segmented stainless steel plates with
rubber facing on both sides.
DIMENSIONS: 12 in. (305 mm) long.
WEIGHT: 70 lbs (32 kg).
SUPPORTING TOOLS: Vertical turret lathe with grinder.
TOOL MAINTENANCE: None required.
QUANTITY PER OPERATION: None required.
REPLACEMENT PARTS LIST
GROUP PART NO. NOMENCLATURE QUANTITY SUPPLIER
NUMBER CODE
G05 2C6529P02 Snubber 12
2C6529P09 Bolt 18
.250-20UNC-2B Wing Nut 18 AP
FOR ALL
2C6529G05
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C6529G05
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
SNUBBER SET, GRINDING - COMPRESSOR STATOR VANES
2C6529G06
PURPOSE AND USE: To hold the stage 4 and stage 5 stator vanes to prevent
vibration during final length grinding operation.
DESCRIPTION: Curved segmented stainless steel plates with
rubber facing on both sides.
DIMENSIONS: 12 in. (305 mm) long.
WEIGHT: 70 lbs (32 kg).
SUPPORTING TOOLS: Vertical turret lathe with grinder.
TOOL MAINTENANCE: None required.
QUANTITY PER OPERATION: None required.
REPLACEMENT PARTS LIST
GROUP PART NO. NOMENCLATURE QUANTITY SUPPLIER
NUMBER CODE
G06 2C6529P03 Snubber 24
2C6529P09 Bolt 36
.250-20UNC-2B Wing Nut 36 AP
FOR ALL
2C6529G06
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C6529G06
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
SNUBBER SET, GRINDING - COMPRESSOR STATOR VANES
2C6529G07
PURPOSE AND USE: To hold the stage 6 stator vanes to prevent vibration
during final length grinding operation.
DESCRIPTION: Curved segmented stainless steel plates with
rubber facing on both sides.
DIMENSIONS: 12 in. (305 mm) long.
WEIGHT: 70 lbs (32 kg).
SUPPORTING TOOLS: Vertical turret lathe with grinder.
TOOL MAINTENANCE: None required.
QUANTITY PER OPERATION: None required.
REPLACEMENT PARTS LIST
GROUP PART NO. NOMENCLATURE QUANTITY SUPPLIER
NUMBER CODE
G07 2C6529P04 Snubber 12
2C6529P06 Bolt 18
.250-20UNC-2B Wing Nut 18 AP
FOR ALL
2C6529G07
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C6529G07
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
SNUBBER SET, GRINDING - COMPRESSOR STATOR VANES
2C6529G08
PURPOSE AND USE: To hold the stage 7 stator vanes to prevent vibration
during final length grinding operation.
DESCRIPTION: Curved segmented stainless steel plates with
rubber facing on both sides.
DIMENSIONS: 12 in. (305 mm) long.
WEIGHT: 70 lbs (32 kg).
SUPPORTING TOOLS: Vertical turret lathe with grinder.
TOOL MAINTENANCE: None required.
QUANTITY PER OPERATION: None required.
REPLACEMENT PARTS LIST
GROUP PART NO. NOMENCLATURE QUANTITY SUPPLIER
NUMBER CODE
G08 2C6529P05 Snubber 12
2C6529P06 Bolt 18
.250-20UNC-2B Wing Nut 18 AP
FOR ALL
2C6529G08
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C6529G08
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
SNUBBER SET, GRINDING - COMPRESSOR STATOR VANES
2C6529G09
PURPOSE AND USE: To hold the stage 1 stator vanes to prevent vibration
during final length grinding operation.
DESCRIPTION: Curved segmented stainless steel plates with
rubber facing on both sides.
DIMENSIONS: 12 in. (305 mm) long.
WEIGHT: 70 lbs (32 kg).
SUPPORTING TOOLS: Vertical turret lathe with grinder.
TOOL MAINTENANCE: None required.
QUANTITY PER OPERATION: None required.
REPLACEMENT PARTS LIST
GROUP PART NO. NOMENCLATURE QUANTITY SUPPLIER
NUMBER CODE
G09 2C6529P10 Snubber 12
2C6529P12 Bolt 36
.250-20UNC-2B Wing Nut 36 AP
FOR ALL
2C6529G09
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C6529G09
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
SNUBBER SET, GRINDING - COMPRESSOR STATOR VANES
2C6529G10
PURPOSE AND USE: To hold the stage 2 stator vanes to prevent vibration
during final length grinding operation.
DESCRIPTION: Curved segmented stainless steel plates with
rubber facing on both sides.
DIMENSIONS: 12 in. (305 mm) long.
WEIGHT: 70 lbs (32 kg).
SUPPORTING TOOLS: Vertical turret lathe with grinder.
TOOL MAINTENANCE: None required.
QUANTITY PER OPERATION: None required.
REPLACEMENT PARTS LIST
GROUP PART NO. NOMENCLATURE QUANTITY SUPPLIER
NUMBER CODE
G10 2C6529P11 Snubber 12
2C6529P12 Bolt 36
.250-20UNC-2B Wing Nut 36 AP
FOR ALL
2C6529G10
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C6529G10
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
STAND, STORAGE - CORE ENGINE, VERTICAL
2C6532G02
FOR ALL
2C6532G02
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C6532G02
Page 2
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FIXTURE SET, PLASMA SPRAY - COMPRESSOR ROTOR
2C6536G07
PURPOSE AND USE: The Plasma Spray Fixture Set is used to hold the compressor
rotor spools for plasma spraying of the aluminum rub coat.
DESCRIPTION: The Plasma Spray Fixture Set consists of a set of masking
rings with a mounting base, stud shafts and a clamping handle. The
fixture is mounted on a rotating table.
DIMENSIONS: 30 x 10 in. (762 x 254 mm).
WEIGHT: 75 lb (34 kg).
SUPPORTING TOOLS: Plasma-Spraying Equipment, Rotating Table.
TOOL MAINTENANCE: None.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing 2C6536.
FOR ALL
2C6536G07
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C6536G07
Page 2
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
DELETED
2C6536G10
PURPOSE AND USE: This tool has been deleted in its entirety.
FOR ALL
2C6536G10
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FIXTURE, MACHINING - COMPRESSOR ROTOR SPOOL, STAGE 3-9 AND SPOOL SHAFT
2C6537G10
PURPOSE AND USE: To hold the compressor rotor stage 3-9 spool or spool shaft
for final machining of the aluminum rub coat.
DESCRIPTION: The tool consists of a base plate, top retainer plate, six
clamps and various screws and nut. Two tracer contour templates are
provided for setting the machining operation.
DIMENSIONS: 26 x 26 x 10 in. (660 x 660 x 250 mm).
WEIGHT: 300 lb (136 kg).
SUPPORTING TOOLS: VTL or engine lathe.
TOOL MAINTENANCE: None.
QUANTITY PER OPERATION: One set.
REPLACEMENT PARTS LIST
GROUP PART NO. NOMENCLATURE QUANTITY SUPPLIER
NUMBER CODE
G10 2C6537P05 Base 1
2C6537P08 Plate, Retainer 1
2C6537P09 Bar, Clamp 6
2C6537P10 Bar, Clamp 6
2C6537P22 Template 1
2C6537P23 Template 1
2C6537P26 Clamp 6
FOR ALL
2C6537G10
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C6537G10
Page 2
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FIXTURE, MACHINING - COMPRESSOR ROTOR SPOOL, STAGE 3-9 AND SPOOL SHAFT
2C6537G11
PURPOSE AND USE: To hold the compressor rotor stage 3-9 spool or spool shaft
for final machining of the aluminum rub coat.
DESCRIPTION: The tool consists of a base plate, top retainer plate, six
clamps and various screws and nut. Two tracer contour templates are
provided for setting the machining operation.
DIMENSIONS: 26 x 26 x 10 in. (660 x 660 x 250 mm).
WEIGHT: 300 lbs (136 kg).
SUPPORTING TOOLS: VTL or engine lathe.
TOOL MAINTENANCE: None.
QUANTITY PER OPERATION: One set.
REPLACEMENT PARTS LIST
GROUP PART NO. NOMENCLATURE QUANTITY SUPPLIER
NUMBER CODE
G11 2C6537P27 Base 1
2C6537P08 Plate, Retainer 1
2C6537P09 Bar, Clamp 6
2C6537P10 Bar, Clamp 6
2C6537P22 Template 1
2C6537P23 Template 1
2C6537P26 Clamp 6
FOR ALL
2C6537G11
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C6537G11
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
GAGE, INSPECTION - COMPRESSOR ROTOR SPOOL, STAGE 3-9
2C6540G02
PURPOSE AND USE: To inspect the compressor rotor spool, stage 3-9,
after machining the aluminum rub coat.
DESCRIPTION: This tool consists of a bridge support with dial
indicators and a set master.
DIMENSIONS: 4 x 7 x 30 in. (100 x 180 x 760 mm).
WEIGHT: 142 lbs (64.5 kg).
SUPPORTING TOOLS: 2C6537 machining fixture.
TOOL MAINTENANCE: Protect unplated or unpainted surfaces with a
corrosion preventive compound.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS LIST
GROUP PART NO. NOMENCLATURE QUANTITY SUPPLIER
NUMBER CODE
G02 2C6540P03 Arm 1
2C6540P04 Spacer 5
2C6540P05 Spacer 1
2C6540P07 Container 1
2C6540P11 Support Assembly 1
2C6540P12 Set Master 1
B3Q W/flat back and Dial Indicator 5 AV
point No. PT 233,
3 in. stem
FOR ALL
2C6540G02
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C6540G02
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
SHIELD, WATER FLOW - STAGE 1 AND 2 BLADE, HIGH PRESSURE TURBINE ROTOR
2C6569G02
PURPOSE AND USE: To confine water spray during flow check of air passages
in high pressure turbine rotor blades.
DESCRIPTION: This tool consists of a plastic cover with holes for using hands
inside of the covered area and a gasket and clamps.
DIMENSIONS: 32 x 20 x 20 in. (812 x 508 x 508 mm).
WEIGHT: To be supplied.
SUPPORTING TOOLS: Water and air flow check fixture, 2C6564.
TOOL MAINTENANCE: None.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS LIST
GROUP PART NO. NOMENCLATURE QUANTITY SUPPLIER
NUMBER CODE
G02 2C6569P09 Base 1
2C6569P10 Gasket 1
2C6569P12 Spacer 10 AJ
205U Clamp 10 AJ
0.750 FF-S Nipple 1 V
32 x 20 x 20 Dome Rectangular Dri-Bel 1 EZ
(Base - 34.50 by Shield
22.50)
FOR ALL
2C6569G02
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C6569G02
Page 2
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
STAND, FLAME SPRAY - STAGE 1 FAN DISK
2C6597G03
PURPOSE AND USE: To hold stage 1 fan rotor disk during flame spray.
DESCRIPTION: This stand is designed as a simple four- wheeled cart with
swivel casters and brakes on one end. The fan rotor disk is bolted to a
flange on an arbor and supported by a ring on this same arbor. The arbor
(holder) and disk are supported by the stand.
DIMENSIONS: 38 x 38 x 31 in. (813 x 965 x 787 mm).
WEIGHT: 190 lbs (86 kg).
SUPPORTING TOOLS: Flame spray equipment, masking set 2C6596.
TOOL MAINTENANCE: Coat black oxide surfaces with corrosion-preventive
oil. Touch-up paint as needed.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS LIST
GROUP PART NO. NOMENCLATURE QUANTITY SUPPLIER
NUMBER CODE
G03 2C6597P02 Stand 1
2C6597P04 Hold Ring 1
2C6597P16 Hold Ring 1
2C6597P17 Holder 1
12-TM-06201-BHC-A-WB Caster Swivel Lock 1 AI
12-TM-06201- BHC-A-R Caster, Rigid 1 AI
FOR ALL
2C6597G03
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C6597G03
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
TOOL, PREBEND, RETAINER - HPC ROTOR BLADE, STAGE 1
2C6599G01
FOR ALL
2C6599G01
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C6599G01
Page 2
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
TOOL, SEATING - RETAINER COMPRESSOR ROTOR BLADE STAGE 1
2C6600G03
PURPOSE AND USE: To hydraulically crimp the stage 1 compressor rotor blade
retainers during installation of blades.
DESCRIPTION: Hydraulically operated tongs (pincers) to squeeze compressor
rotor blade retainers during installation of blades.
DIMENSIONS: 4 x 8 x 15 in. (100 x 205 x 380 mm).
WEIGHT: 35 lb (16 kg).
SUPPORTING TOOLS: Hydraulic Pump and Retainer Prebend Tool, 2C6599.
TOOL MAINTENANCE: Coat treated surfaces (black oxide) with corrosion preventive
light oil when stored. Load test periodically (see GE drawing 2C6600 for load test
diagram and applicable NOTE). Apply a light coat of oil to all surfaces when stored.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS LIST
GROUP PART NO. NOMENCLATURE QUANTITY SUPPLIER
NUMBER CODE
G03 2C6600P04 Swivel Bracket 1
2C6600P05 Mounting Plate 1
2C6600P15 Right Leg 1
2C6600P16 Left Leg 1
2C6600P17 Lift Adapter 1
2C6600P18 Lift Bar 1
SPL-972-RO Hydraulic Cylinder 1 D
FOR ALL
2C6600G03
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C6600G03
Page 2
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
GAGE, IMMERSION DEPTH - IGNITER PLUG
2C6613G01
PURPOSE AND USE: To check the immersion depth of the igniter plug
into the combustion chamber.
DESCRIPTION: This gage consists of a standard vernier type depth gage with a
special sleeve with a carbide tip and storage case.
DIMENSIONS: 8 x 3 in. (205 x 75 mm).
WEIGHT: 2 lb (0.9 kg).
SUPPORTING TOOLS: Standard hand tools.
TOOL MAINTENANCE: Apply a light coat of oil to all surfaces when stored.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: None required.
FOR ALL
2C6613G01
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C6613G01
Page 2
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
TOOL SET, HOLDING - COMPRESSOR ROTOR BOLTS
2C6620G01
FOR ALL
2C6620G01
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C6620G01
Page 2
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FIXTURE, GAGING - FAN FORWARD SHAFT/FAN MIDSHAFT
2C6621G03
PURPOSE AND USE: To measure the axial distance between forward surfaces of
midshaft and front mounting flange of forward shaft.
DESCRIPTION: This fixture consists of a gage plate, depth
micrometer, and a plastic case.
DIMENSIONS: 8 x 3 x 0.5 in. (205 x 75 x 13 mm).
WEIGHT: 8 lb (3.6 kg).
SUPPORTING TOOLS: None required.
TOOL MAINTENANCE: Clean and lubricate with light oil after each use. Periodic
inspection of depth micrometer is required.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS LIST
GROUP PART NO. NOMENCLATURE QUANTITY SUPPLIER
NUMBER CODE
G03 2C6621P02 Bar 1
2C6621P06 Nameplate 1
No. 445 Body with Micrometer Depth Gage 1 AZ
12-13 in. Range Rod
P-61L Plastic Case 1 EP
FOR ALL
2C6621G03
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C6621G03
Page 2
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
PYLON, INDICATOR - COMPRESSOR ROTOR BUILDUP
2C6629G01
PURPOSE AND USE: To indicate compressor rotor subassemblies during rotor buildup
in conjunction with fixture, buildup compressor rotor 2C6624.
DESCRIPTION: This tool consists of a welded pylon assembly, clamp, boss,
arm, spacer, retainer plate, 2 support halves, cap, T-handle, indicator
rods, indicator and supporting hardware.
DIMENSIONS: 20 x 20 x 82 in. (510 x 510 x 2080 mm).
WEIGHT: 420 lb (191 kg).
SUPPORTING TOOLS: Used with compressor rotor build-up fixture 2C6624.
TOOL MAINTENANCE: Coat treated surfaces (black oxide) with corrosion preventive
light oil. Coat surface M of item 10 and exposed areas of item 16 with
Spray-Kote bonded coating 0.0002-0.0005 in. (0.005-0.013 mm) thick at
assembly, Dow Corning Corporation, Midland, MI.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS LIST
GROUP PART NO. NOMENCLATURE QUANTITY SUPPLIER
NUMBER CODE
G01 2C6629P02 Pylon 1
2C6629P03 Clamp 1
2C6629P04 Boss 1
2C6629P05 Arm, Tubing 1
2C6629P06 Spacer 1
2C6629P07 Plate, Retainer 1
2C6629P08 Support, Half 1
2C6629P09 Support, Half 1
2C6629P10 Cap 1
2C6629P11 Handle, T 1
2C6629P12 Counterweight 1
2C6629P13 Rod, Indicator 1
2C6629P14 Rod, Indicator 1
406-19 Single Row Radial Brg 1 BR
1/8 Dia 7 x 19 SST per Wire Rope 1 BS
MIL-C-5424 83 ± 1 Long
G450 Clip Size 1/8 Wire Rope Clip 2 AB
G291 1/4 x 2 Eye Bolt, Regular Nut 1 AB
G291 1/2 x 12 Eye Bolt, Regular Nut 1 AB
800 SMZ Indicator 1 BT
FOR ALL
2C6629G01
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C6629G01
Page 2
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
TOOL SET, SPACERS - COMPRESSOR ROTOR BUILDUP
2C6635G04
PURPOSE AND USE: To buildup the compressor rotor component subassemblies. They
permit bolting together the subassemblies for making runout and flatness checks.
DESCRIPTION: To buildup the compressor rotor component subassemblies. They permit
bolting together the subassemblies for making runout and flatness checks.
DIMENSIONS: Container: 4 x 6 in. (100 x 150 mm).
WEIGHT: 0.5 lb (0.3 kg).
SUPPORTING TOOLS: Stand hand tools and rotor buildup equipment.
TOOL MAINTENANCE: None required.
QUANTITY PER OPERATION: One set.
REPLACEMENT PARTS LIST
GROUP PART NO. NOMENCLATURE QUANTITY SUPPLIER
NUMBER CODE
G04 2C6635P03 Spacer 30
2C6335P05 Container 1
2C6635P09 Spacer 18
FOR ALL
2C6635G04
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C6635G04
Page 2
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
PULLER, VANE ARM AND VANE SPACER
2C6645G02
PURPOSE AND USE: To remove vane arm and vane arm spacer from
end of vane on stages 5 and 6.
DESCRIPTION: This tool is a special hooked puller and jackscrew
to pull vane arm and spacer.
DIMENSIONS: 2 x 1.25 x 0.75 in. (50 x 30 x 20 mm).
WEIGHT: 1 lb (0.5 kg).
SUPPORTING TOOLS: None required.
TOOL MAINTENANCE: Coated treated surfaces (black oxide) with corrosion
preventive light oil when stored.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS LIST
GROUP PART NO. NOMENCLATURE QUANTITY SUPPLIER
NUMBER CODE
G02 2C6645P03 Jackscrew 1
2C6645P05 Puller 1
FOR ALL
2C6645G02
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C6645G02
Page 2
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
GAGE BLOCK, COMPRESSOR STATOR VANE ACTUATION ARM - STAGES 5 AND 6
2C6646G01
PURPOSE AND USE: The Compressor Stator Vane Actuation Arm Gage Block
is used to check the straightness of the double nut stages 5 and 6
compressor stator vane lever arms.
DESCRIPTION: The Compressor Stator Vane Actuation Arm Gage Block is a gage and pin
that indicates if the arm is bent beyond limits. The tool has a black oxide finish.
DIMENSIONS: 3.25 x 1.5 x 1 in. (83 x 38 x 25 mm).
WEIGHT: 2 lb (1 kg).
SUPPORTING TOOLS: None.
TOOL MAINTENANCE: Apply corrosion preventive oil to all surfaces
that have a black oxide finish.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing 2C6646.
FOR ALL
2C6646G01
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C6646G01
Page 2
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
WRENCH, SPANNER - COMPRESSOR STATOR VANE SPACER
2C6647G01
FOR ALL
2C6647G01
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C6647G01
Page 2
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
TOOL, NUT STARTING - COMPRESSOR ROTOR - STAGES 3-9
2C6649G02
PURPOSE AND USE: To start nuts on bolts of the 9th-stage rotor joint during
installation of spool 3 through 9 of the compressor rotor.
DESCRIPTION: The tool consists of a steel bar with two drive gears and a drive
bolt. The end gear has a spline socket to drive the No. 12 nut. A piece of
tubing over the socket holds the nut to the wrench while being started.
DIMENSIONS: 1 x 1 x 14 in. (25 x 25 x 356 mm).
WEIGHT: 3 lbs (1.4 kg).
SUPPORTING TOOLS: 2C6620 and 2C6937.
TOOL MAINTENANCE: None.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS LIST
GROUP PART NO. NOMENCLATURE QUANTITY SUPPLIER
NUMBER CODE
G02 2C6649P03 Pulley, Thumb 1
2C6649P09 Handle 1
2C6649P10 Pulley, Socket 1
2C6649P11 Sleeve 6
FOR ALL
2C6649G02
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C6649G02
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FIXTURE ASSEMBLY, GRIND HIGH PRESSURE COMPRESSOR BLADE PLATFORMS STAGES 3 THROUGH 16
2C6661G01
PURPOSE AND USE: To grind blade platforms for rotor assembly operations.
DESCRIPTION: This assembly is comprised of grind fixture 2C6663 mounted to
cross slide base 2C6662, and is used to grind high pressure compressor blade
platforms stages 3 through 16 for rotor assembly operations.
DIMENSIONS: 14 x 14 x 8 in. (356 x 356 x 203 mm).
WEIGHT: 55 lbs (30 kg).
SUPPORTING TOOLS: Belt sander with table.
TOOL MAINTENANCE: No special requirements.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS LIST
GROUP PART NO. NOMENCLATURE QUANTITY SUPPLIER
NUMBER CODE
G01 2C6662G01 Base, Fixture Set
2C6663G01 Fixture, Holding
2C6663G02 Fixture, Holding
2C6663G03 Fixture, Holding
2C6663G04 Fixture, Holding
FOR ALL
2C6661G01
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C6661G01
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
CROSS SLIDE BASE, GRIND HIGH PRESSURE COMPRESSOR BLADE PLATFORMS STAGES 3 THROUGH 16
2C6662G01
FOR ALL
2C6662G01
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C6662G01
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FIXTURE, GRIND - HIGH PRESSURE COMPRESSOR BLADE PLATFORM, STAGES 3 THROUGH 16
2C6663G01
FOR ALL
2C6663G01
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C6663G01
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FIXTURE, GRIND - HIGH PRESSURE COMPRESSOR BLADE PLATFORM, STAGES 3 THROUGH 16
2C6663G02
FOR ALL
2C6663G02
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C6663G02
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FIXTURE, GRIND - HIGH PRESSURE COMPRESSOR BLADE PLATFORM, STAGES 3 THROUGH 16
2C6663G03
FOR ALL
2C6663G03
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C6663G03
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FIXTURE, GRIND - HIGH PRESSURE COMPRESSOR BLADE PLATFORM, STAGES 3 THROUGH 16
2C6663G04
FOR ALL
2C6663G04
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C6663G04
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
PULLER, FAN FORWARD AND FAN MID SHAFT
2C6671G04
PURPOSE AND USE: The Fan Forward and Fan Mid Shaft Puller is used to separate
the fan forward and fan mid shaft assemblies.
DESCRIPTION: The Fan Forward and Fan Mid Shaft Puller is a large capacity
pump, 10 feet of hose, pressure gage, quick disconnect fittings, a ram
support, pusher tube and spacer plate.
DIMENSIONS: 26 x 12 x 9 in. (660 x 305 x 229 mm).
WEIGHT: 125 lbs (57 kg).
SUPPORTING TOOLS: 2C6075 (PRE SB 72-1047) or 2C14890 (SB 72-1047).
TOOL MAINTENANCE: TBD
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing 2C6671.
FOR ALL
2C6671G04
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C6671G04
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
DELETED
2C6671G05
PURPOSE AND USE: This tool has been deleted in its entirety.
FOR ALL
2C6671G05
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
EYE, LIFT - COMPRESSOR ROTOR
2C6800G02
PURPOSE AND USE: To remove the compressor rotor from the engine and
to handle through repair operations.
DESCRIPTION: Lift eye with flanges to fit compressor rotor disk.
DIMENSIONS: 17 in. (180 mm) diameter.
WEIGHT: 7 lbs (3 kg).
SUPPORTING TOOLS: Hoist, portable or fixed.
TOOL MAINTENANCE: Apply a light coat of oil to all surfaces when stored. Load test
periodically (see GE drawing 2C6800 for load test diagram and applicable NOTE).
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS LIST
GROUP PART NO. NOMENCLATURE QUANTITY SUPPLIER
NUMBER CODE
G02 2C6800P02 Forward Lift Hub 1
1348 Eye Bolt 1 AS
FOR ALL
2C6800G02
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C6800G02
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
EYE, LIFT - COMPRESSOR ROTOR
2C6800G03
PURPOSE AND USE: To remove the compressor rotor from the engine and
to handle through repair operations.
DESCRIPTION: Lift eye with flanges to fit compressor rotor disk. This
tool has increased load capacity for LM6000 but is also applicable to
CF6-80C2, CF650, CF6-80A, and CF6-80E1.
DIMENSIONS: 17 in. (180 mm) diameter.
WEIGHT: 7 lbs (3 kg).
SUPPORTING TOOLS: Hoist, portable or fixed.
TOOL MAINTENANCE: Apply a light coat of oil to all surfaces when stored. Load test
periodically (see GE drawing 2C6800 for load test diagram and applicable NOTE).
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS LIST
GROUP PART NO. NOMENCLATURE QUANTITY SUPPLIER
NUMBER CODE
G03 2C6800P02 Forward Lift Hub 1
1348 Eye Bolt 1 AS
FOR ALL
2C6800G03
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C6800G03
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
PROTECTOR - COMPRESSOR FORWARD SHAFT, FAN MID SHAFT
2C6803G01
PURPOSE AND USE: The Protector is used to protect the fan mid shaft
during removal from the core engine.
DESCRIPTION: The Protector consists of a plastic sleeve and metal ring which fits
into the compressor rotor shaft to protect the bearing race.
DIMENSIONS: 7.5 x 4.5 in. (191 x 114 mm).
WEIGHT: 2 lbs (1 kg).
SUPPORTING TOOLS: None.
TOOL MAINTENANCE: None.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing 2C6803.
FOR ALL
2C6803G01
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C6803G01
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
DELETED
2C6803G02
PURPOSE AND USE: This tool has been deleted in its entirety.
FOR ALL
2C6803G02
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
WRENCH, SPANNER NUT - NO. 3 BEARING
2C6805G02
FOR ALL
2C6805G02
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C6805G02
Page 2
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
PULLER, NO. 3 BEARING - INNER RACE
2C6815G01
PURPOSE AND USE: To remove the No. 3 bearing inner race from the
compressor rotor forward shaft.
DESCRIPTION: A split sleeve is designed to engage the rear of the No. 3 bearing
race and the pressure plate for the hydraulic puller. A hydraulic cylinder and
pressure plate supplies the force to pull the bearing race. A ring is provided
to hold the halves of the split-sleeve together. Pressure to extend the puller
is supplied with a standard hand operated hydraulic pump.
DIMENSIONS: 6.75 in. (172 mm) diameter.
2C6815P05 Ring 1
2C6815P06 Plate 1 BU
CB-1005-38-01 Hydraulic Cylinder 1 F
41107 Spherical Washer 1 G
B1500-047 Belleville Washer 1 BU
XF-9901-30-11 3/8 Coupler 1 BU
XP-9901-30-11 Dust Cover 1 C
MIT-20 Thumb Screw 1
FOR ALL
2C6815G01
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C6815G01
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
PULLER, MANIFOLD - NO. 1 BEARING
2C6823G01
PURPOSE AND USE: To assemble and disassemble the No. 1 bearing manifold.
DESCRIPTION: A base and handle with four captured screws for
attaching to the manifold.
DIMENSIONS: 4 x 9 in. (100 x 230 mm).
WEIGHT: 3 lbs (1.4 kg).
SUPPORTING TOOLS: None required.
TOOL MAINTENANCE: None required.
QUANTITY PER OPERATION: One.
FOR ALL
2C6823G01
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C6823G01
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
ADAPTER, TORQUE, COUPLING NUT - FAN MAINTENANCE UNIT TO FAN MID SHAFT
2C6833G05
PURPOSE AND USE: To apply torque during installation or removal of the coupling
nut, connecting the forward fan shaft to the fan midshaft.
DESCRIPTION: The tool consists of a splined torque tube which engages the
internal spline to the coupling nut. An anti-torque engages the fan midshaft.
An indexing tube engages into the forward shaft of the coupling nut. Torque
tube engages into outer slots of coupling nut. A torque multiplier is
installed at the end of torque tube to apply the force.
DIMENSIONS: 44 x 11 x 16 in. (1120 x 28 x 406 mm).
WEIGHT: 170 lbs (77 kg).
SUPPORTING TOOLS: Sweeney Torque Multiplier 8100 or 8200.
TOOL MAINTENANCE: TBD
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS LIST
GROUP PART NO. NOMENCLATURE QUANTITY SUPPLIER
NUMBER CODE
G05 2C6833P04 Indexing Tube 1
2C6833P06 Anchor Screw 10
2C6833P07 Spacer 1
2C6833P10 Locating Pin 1
2C6833P12 Torque Tube 1
2C6833P15 Indexing Tube 1
2C6833P16 Hand Stop 2
2C6833P19 Support 1
FOR ALL
2C6833G05
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C6833G05
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
PUSHER, INNER RACE - NO. 2 BEARING
2C6836G01
FOR ALL
2C6836G01
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C6836G01
Page 2
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FIXTURE, LIFT - FAN ROTOR SUBASSEMBLY
2C6856G03
PURPOSE AND USE: The lift fixture is used to remove the fan rotor from
the engine and transport it to a storage stand.
DESCRIPTION: The lift fixture is a C-shaped fixture with an adjustable center
of gravity lift eye. The primary color of the tool is blue.
DIMENSIONS: 80 x 60 x 6 in. (2,032 x 1,524 x 152.4 mm).
WEIGHT: 200 lbs (90.7 kg).
SUPPORTING TOOLS: Fixed or portable overhead hoist, 2C14686G05, 2C14227G02.
TOOL MAINTENANCE: Apply corrosion preventive oil to all surfaces that
have black oxide or black phosphate coating.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing 2C6856.
FOR ALL
2C6856G03
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C6856G03
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FIXTURE, LIFT - FAN ROTOR SUBASSEMBLY
2C6856G04
PURPOSE AND USE: The lift fixture is used to remove the fan rotor from
the engine and transport it to a storage stand.
DESCRIPTION: The lift fixture is a C-shaped fixture with an adjustable center
of gravity lift eye. The primary color of the tool is blue. The G04 version
of this tool is the recommended tool and has a modified frame, support bracket,
and crank handle. The frame height is 23 in. (584.2 mm) less than the G03,
designed for in-shop use when the engine is not on a pylon.
DIMENSIONS: 80 x 60 x 6 in. (2,032 x 1,524 x 152.4 mm).
WEIGHT: 150 lbs (68 kg).
SUPPORTING TOOLS: Fixed or portable overhead hoist, 2C14686G05, 2C14227G02.
TOOL MAINTENANCE: Apply corrosion preventive oil to all surfaces that
have black oxide or black phosphate coating.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing 2C6856.
FOR ALL
2C6856G04
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C6856G04
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
WRENCH, CENTER VENT DUCT
2C6876G02
PURPOSE AND USE: To remove and install center vent tube in mid shaft.
DESCRIPTION: Keyed wrench and adapter to engage vent tube and mid shaft.
DIMENSIONS: 9 x 6 x 5 in. (29 x 152 x 127 mm).
WEIGHT: 10 lb (4.5 kg).
SUPPORTING TOOLS: Torque wrench; 0.75 in. (19 mm) male drives (2).
TOOL MAINTENANCE: None.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS LIST
GROUP PART NO. NOMENCLATURE QUANTITY SUPPLIER
NUMBER CODE
G02 2C6876P02 Wrench 1
2C6876P04 Key 4
2C6876P05 Key 2
2C6876P08 Adapter 1
FOR ALL
2C6876G02
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C6876G02
Page 2
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FIXTURE, INSPECTION - FAN FORWARD/FAN MIDSHAFT SEATING
2C6877G01
PURPOSE AND USE: To establish a reference surface for drop checks to check
seating of forward fan shaft to fan midshaft.
DESCRIPTION: A Vee block with a padded U-bolt.
DIMENSIONS: 8 x 8 in. (205 x 205 mm).
WEIGHT: TBD
SUPPORTING TOOLS: Depth Micrometer and Truck, 2C6012.
TOOL MAINTENANCE: None required.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS LIST
GROUP PART NO. NOMENCLATURE QUANTITY SUPPLIER
NUMBER CODE
G01 2C6877P02 Vee Block Guide 1
2C6877P03 U-Bolt 1
2C6877P04 Plate 1
CL-147 Spherical Washer 2 I
CL-127 Flange Nut 2 I
FOR ALL
2C6877G01
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C6877G01
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
TEMPLATE, LEADING EDGE - FAN BLADE STAGE 1
2C6879P01
PURPOSE AND USE: To inspect the Stage 1 Fan Blade Leading Edge
contour blades 9010M33 and 9081M53.
DESCRIPTION: This tool is a thin template made of stainless steel type 430.
DIMENSIONS: 1.5 x 1.0 x 0.1 in. (38.1 x 25.4 x 2.54 mm).
WEIGHT: 0.75 oz (21 g).
SUPPORTING TOOLS: N/A.
TOOL MAINTENANCE: Not required.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing 2C6879.
FOR ALL
2C6879P01
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C6879P01
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
TOOL, INSTALLATION - SELF WRENCHING BOLT, COMPRESSOR ROTOR
2C6888G03
PURPOSE AND USE: This tool is to install self wrenching bolts into
the compressor rotor spools.
DESCRIPTION: This tool is composed of two pieces of hardened steel,
configured to fit the spool, which are bolted together with a shoulder
bolt to form a plier-like device.
DIMENSIONS: 8 x 2 x 1 in. (203 x 51 x 25 mm).
WEIGHT: 1 lb (0.4 kg).
SUPPORTING TOOLS: Not required.
TOOL MAINTENANCE: Apply corrosion preventive oil to all surfaces
that have black oxide finishing.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing 2C6888.
FOR ALL
2C6888G03
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C6888G03
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
TOOL, REMOVAL - FAN SPINNER
2C6894G03
PURPOSE AND USE: The Removal Tool is used to remove the fan rotor spinner
from the stage 1 fan disk during overhaul.
DESCRIPTION: The Removal Tool is a round pry bar with a tapered end and
a nylon pad to protect the fan rotor blades.
DIMENSIONS: 1 x 9 x 6 in. (25 x 229 x 152 mm).
WEIGHT: 2 lbs (1 kg).
SUPPORTING TOOLS: None.
TOOL MAINTENANCE: None.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing 2C6894.
FOR ALL
2C6894G03
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C6894G03
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
TOOL, REMOVAL - FAN SPINNER
2C6894G04
PURPOSE AND USE: The Removal Tool is used to remove the fan rotor spinner
from the stage 1 fan disk during overhaul.
DESCRIPTION: The Removal Tool is a round pry bar with a tapered end and a nylon
pad to protect the fan rotor blades. This tool incorporates a longer bar than
the G03, to increase leverage in prying off the spinner.
DIMENSIONS: 1 x 9 x 6 in. (25 x 229 x 152 mm).
WEIGHT: 2 lbs (1 kg).
SUPPORTING TOOLS: None.
TOOL MAINTENANCE: None.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing 2C6894.
FOR ALL
2C6894G04
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C6894G04
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
GUIDE PIN, FAN DISK - STAGE 1
2C6920P01
PURPOSE AND USE: To guide fan rotor spinner onto fan rotor disk.
DESCRIPTION: These are tapered pins that screw into fan rotor disk flange and
guide the fan rotor spinner onto fan rotor disk mounting flange.
DIMENSIONS: 0.4 in. dia x 4.3 in. (10 mm dia x 110 mm).
WEIGHT: 1 lb (0.45 kg).
SUPPORTING TOOLS: Hand tools.
TOOL MAINTENANCE: None required.
QUANTITY PER OPERATION: One set of three pins.
REPLACEMENT PARTS: None required.
FOR ALL
2C6920P01
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C6920P01
Page 2
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
DELETED
2C6925G03
PURPOSE AND USE: This tool has been deleted in its entirety.
Superseded by tool 2C6925G05.
FOR ALL
2C6925G03
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
GAGE, SET - VARIABLE STATOR VANE CLEVIS ASSEMBLIES
2C6925G05
PURPOSE AND USE: The Set Gage is used to measure and set variable stator
vane clevis assemblies to necessary length.
DESCRIPTION: The Set Gage is a rectangular baseplate with a rod on one end,
a pin to hold the clevis, and an adjustable pin to fit the spherical rod
end bearing. The tool has a black oxide finish.
DIMENSIONS: 7.5 x 2.5 x 4 in. (190 x 64 x 102 mm).
WEIGHT: 7 lbs (3.2 kg).
SUPPORTING TOOLS: Standard hand tools.
TOOL MAINTENANCE: Apply corrosion preventive oil to all surfaces
that have a black oxide finish.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing 2C6925.
FOR ALL
2C6925G05
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C6925G05
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FIXTURE, LEAK CHECK - A-SUMP, FAN FRAME
2C6934G04
PURPOSE AND USE: To pressure check the A-sump, using shop air pressure.
DESCRIPTION: This fixture provides a front and rear cover for the A-sump area
with a tie bolt between the two covers. There are other covers provided for
radial drive shaft pad and strut openings. The front cover contains a gage,
shutoff valve, pressure relief valve, and air inlet connection for the customer
furnished pressure regulated and filtered air supply.
DIMENSIONS: 20 in. dia x 38 in. (510 mm dia x 965 mm).
WEIGHT: 45 lb (20 kg).
SUPPORTING TOOLS: Shop air supply.
TOOL MAINTENANCE: Apply a light coat of oil to all surfaces when stored.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: See GE drawing 2C6934.
FOR ALL
2C6934G04
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C6934G04
Page 2
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
ADAPTER, TORQUE, SET - COMPRESSOR ROTOR
2C6937G07
PURPOSE AND USE: The Torque Adapter Set is used to assemble and
disassemble the compressor rotor.
DESCRIPTION: The Torque Adapter Set is wrenches and adapters used to
install and remove the nuts at stage 10.
DIMENSIONS: 4 x 4 x 12 in. (102 x 102 x 305 mm).
WEIGHT: 2 lb (1 kg).
SUPPORTING TOOLS: 3/4 in. Torque Ratchet Wrenches.
TOOL MAINTENANCE: None.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing 2C6937.
FOR ALL
2C6937G07
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C6937G07
Page 2
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
ADAPTER, TORQUE, SET - COMPRESSOR ROTOR
2C6937G08
PURPOSE AND USE: The Torque Adapter Set is used to assemble and
disassemble the compressor rotor.
DESCRIPTION: The Torque Adapter Set is wrenches and adapters used to
install and remove the nuts at stage 10.
DIMENSIONS: 4 x 4 x 12 in. (102 x 102 x 305 mm).
WEIGHT: 2 lb (1 kg).
SUPPORTING TOOLS: 3/4 in. Torque Ratchet Wrenches.
TOOL MAINTENANCE: None.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing 2C6937.
FOR ALL
2C6937G08
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C6937G08
Page 2
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
BORESCOPE GUIDE TUBE
2C6948P05
PURPOSE AND USE: The Borescope Guide Tube is used to guide the borescope
light and viewing cable tube in the high pressure turbine stator
port without damaging the cable.
DESCRIPTION: The Borescope Guide Tube is a 0.5 in. (13 mm) hollow tube with a
single curve. The tube goes through a rectangular block at one end.
DIMENSIONS: 6 x 4.5 in. (152 x 114 mm).
WEIGHT: 0.25 lb (0.1 kg).
SUPPORTING TOOLS: A borescope having a small diameter light and viewing cable.
TOOL MAINTENANCE: None.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing 2C6948.
FOR ALL
2C6948P05
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C6948P05
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
BORESCOPE GUIDE TUBE
2C6948P06
PURPOSE AND USE: The Borescope Guide Tube is used to guide the borescope light and
viewing cable tube in the high pressure turbine stator port without damaging the
cable. The P06 guide tube has a different configuration than the P05.
DESCRIPTION: The Borescope Guide Tube is a 0.5 in. (13 mm) hollow tube with a
single curve. The tube goes through a rectangular block at one end.
DIMENSIONS: 6 x 4.5 in. (152 x 114 mm).
WEIGHT: 0.25 lb (0.1 kg).
SUPPORTING TOOLS: A borescope having a small diameter light and viewing cable.
TOOL MAINTENANCE: None.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing 2C6948.
FOR ALL
2C6948P06
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C6948P06
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
KIT, SPLIT ENGINE, ALIGNMENT
2C6958G01
PURPOSE AND USE: The Split Engine Alignment Kit is used to align the fan
frame and compressor stator case before assembly.
DESCRIPTION: The Split Engine Alignment Kit consists of a modified 6
in. vernier caliper and two stop blocks.
DIMENSIONS: Container, 4 x 8 in. (102 x 203 mm).
WEIGHT: 1 lb (0.5 kg).
SUPPORTING TOOLS: None.
TOOL MAINTENANCE: None.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing 2C6958.
FOR ALL
2C6958G01
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C6958G01
Page 2
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
GAGE SET, SIGHT - COMPRESSOR STATOR VANE ACTUATION ARMS
2C6962G05
PURPOSE AND USE: The Sight Gage Set is used to check for bent variable
stator vane (VSV) lever arms on an on-wing engine.
DESCRIPTION: The Sight Gage Set is two cylindrical rings (with slots) on
L-shaped arms that have scribed gaging lines.
DIMENSIONS: Container, 6 x 6 x 4 in. (152 x 152 x 102 mm).
WEIGHT: 5 lb (2 kg).
SUPPORTING TOOLS: 2C6966, 2C8016.
TOOL MAINTENANCE: Apply corrosion preventive oil to all surfaces
that have a black oxide finish.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing 2C6962.
FOR ALL
2C6962G05
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C6962G05
Page 2
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
GAGE SET, COMPRESSOR STATOR VANE ACTUATION ARMS IGV AND STAGES 1 THROUGH 4
2C6963G04
PURPOSE AND USE: To check the amount of bend in the compressor stator vane
actuation arms of inlet guide vanes and stages 1 through 4.
DESCRIPTION: The actuation arm is placed on gage block and the gage block
provides visual reference to the amount of bend in the arm.
DIMENSIONS: 8 x 4 x 4 in. (205 x 100 x 100 mm).
WEIGHT: 10 lbs (4.5 kg).
SUPPORTING TOOLS: Standard hand tools.
TOOL MAINTENANCE: Coat treated surfaces (black oxide) with corrosion
preventive light oil when stored.
QUANTITY PER OPERATION: One set.
REPLACEMENT PARTS LIST
GROUP PART NO. NOMENCLATURE QUANTITY SUPPLIER
NUMBER CODE
G04 2C6963P02 Gage 1
2C6963P03 Gage 1
2C6963P04 Gage 1
2C6963P05 Gage 1
2C6963P10 Container 1
FOR ALL
2C6963G04
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C6963G04
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
WRENCH, TORQUE BREAKING - COMPRESSOR STATOR VANE ACTUATING ARM - RETAINING NUT
2C6964G04
PURPOSE AND USE: To break torque on compressor stator actuation arm retaining nuts.
DESCRIPTION: The body holds actuation arm while a socket is used to
break torque on retaining nut.
DIMENSIONS: 14 x 7 in. (355 x 180 mm).
WEIGHT: TBD
SUPPORTING TOOLS: Standard hand tools.
TOOL MAINTENANCE: Coat treated surfaces (black oxide) with corrosion
preventive light oil when stored.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS LIST
GROUP PART NO. NOMENCLATURE QUANTITY SUPPLIER
NUMBER CODE
G04 2C6964P02 Wrench 1
2C6964P03 Wrench 1
2C6964P06 Container 1
FOR ALL
2C6964G04
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C6964G04
Page 2
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
WRENCH, TORQUE - NUT RETAINING COMPRESSOR STATOR ACTUATION ARMS
2C6965P01
PURPOSE AND USE: The Torque Wrench is used to torque the compressor
stator actuation arm retaining nuts.
DESCRIPTION: The Torque Wrench has a preset torque of 70 lbs in.
(7.9 N.m) which makes it unlikely to exceed the torque value that is
required for the retaining nuts.
DIMENSIONS: 10 x 1.5 in. (254 x 38 mm).
WEIGHT: 1.5 lbs (1 kg).
SUPPORTING TOOLS: None.
TOOL MAINTENANCE: Periodically check the preset torque values.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing 2C6965.
FOR ALL
2C6965P01
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C6965P01
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
WRENCH, TORQUE - NUT RETAINING COMPRESSOR STATOR ACTUATION ARMS
2C6965P03
PURPOSE AND USE: The Torque Wrench is used to torque the compressor
stator actuation arm retaining nuts.
DESCRIPTION: The Torque Wrench has a preset torque of 92 lbs in.
(10.4 N.m) which makes it unlikely to exceed the torque value that is
required for the retaining nuts.
DIMENSIONS: 10 x 1.5 in. (254 x 38 mm).
WEIGHT: 1.5 lbs (1 kg).
SUPPORTING TOOLS: None.
TOOL MAINTENANCE: Periodically check the preset torque values.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing 2C6965.
FOR ALL
2C6965P03
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C6965P03
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
GAGE SET, COMPRESSOR STATOR VANE - ACTUATION ARMS
2C6966G05
FOR ALL
2C6966G05
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C6966G05
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
GAGE SET, COMPRESSOR STATOR VANE - ACTUATION ARMS
2C6966G07
FOR ALL
2C6966G07
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C6966G07
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
TOOL, INSTALLATION - STAGE 2 COMPRESSOR ROTOR BLADE RETAINER STOP
2C6967G06
PURPOSE AND USE: The Installation Tool is used to install the stage 2
compressor rotor blade stop on an assembled rotor.
DESCRIPTION: The Installation Tool consists of a moveable arm with a
hook that hinges on a base plate.
DIMENSIONS: 12 x 5 x 2 in. (305 x 127 x 51 mm).
WEIGHT: TBD
SUPPORTING TOOLS: None.
TOOL MAINTENANCE: Apply corrosion preventive oil to all surfaces that
have black oxide or black phosphate coating.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing 2C6967.
FOR ALL
2C6967G06
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C6967G06
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
TOOL, INSTALLATION - STAGE 2 COMPRESSOR ROTOR BLADE RETAINER STOP
2C6967G08
PURPOSE AND USE: The Installation Tool is used to install the stage 2
compressor rotor blade stop on a disassembled rotor.
DESCRIPTION: The Installation Tool consists of a moveable arm with a hook
that hinges on a base plate and a flanged spool that provides the support
provided by the compressor spool for the 2C6967G06.
DIMENSIONS: 12 x 5 x 2 in. (305 x 127 x 51 mm) and 13.2 in dia x 6 in.
(335.28 mm dia x 152.4 in.) flanged spool.
WEIGHT: TBD
SUPPORTING TOOLS: None.
TOOL MAINTENANCE: Apply corrosion preventive oil to all surfaces that
have black oxide or black phosphate coating.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing 2C6967.
FOR ALL
2C6967G08
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C6967G08
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
TOOL, REMOVAL - STAGE 2 COMPRESSOR BLADE RETAINER STOP
2C6968G02
FOR ALL
2C6968G02
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C6968G02
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
TOOL, REMOVAL - STAGE 2 COMPRESSOR BLADE RETAINER STOP
2C6968G04
PURPOSE AND USE: To remove the stage 2 compressor rotor blade retainer
stop on a disassembled rotor.
DESCRIPTION: A plate backs up front of blade retainer pin while one
anvil is inserted under one leg of the retainer tab and the other anvil
is placed on top of the other retainer tab. As the top anvil is forced
down the retainer stop is released.
DIMENSIONS: 14.75 in. dia x 0.75 in. (374.65 mm dia x 19.05 mm).
WEIGHT: 16 lbs (7.3 kg).
SUPPORTING TOOLS: None required.
TOOL MAINTENANCE: Coat treated surfaces (black oxide) with corrosion
preventive light oil when stored.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS LIST
GROUP PART NO. NOMENCLATURE QUANTITY SUPPLIER
NUMBER CODE
G04 2C6968P11 Plate 1
2C6968P17 Dowel Pin 2
FOR ALL
2C6968G04
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C6968G04
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
MICROMETER SET, STATOR CASE WEAR
2C6969G01
PURPOSE AND USE: To measure compressor stator case vane hole wear.
DESCRIPTION: Standard micrometers with reworked tips and special spindle and anvil.
DIMENSIONS: 6 x 3 in. (152 x 76 mm).
WEIGHT: 1 lb (0.5 kg).
SUPPORTING TOOLS: None.
TOOL MAINTENANCE: Standard precision instrument care and periodic inspection.
QUANTITY PER OPERATION: One set per unit.
REPLACEMENT PARTS LIST
GROUP PART NO. NOMENCLATURE QUANTITY SUPPLIER
NUMBER CODE
G01 2C6969P02 Container 1
2C6969P03 Micrometer 1
700A Micrometer ID 1 AZ
700B Micrometer ID 1
FOR ALL
2C6969G01
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C6969G01
Page 2
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
PUMP, HAND - COWL DOOR ACTUATOR - FAN REVERSER
2C6983P08
PURPOSE AND USE: The Hand Pump is used to actuate the fan reverser cowl doors.
DESCRIPTION: The Hand Pump is a hand-operated hydraulic pump and hose with quick
disconnect and dust cover. The primary color of the tool is blue.
DIMENSIONS: 23 x 6 x 6 in. (584 x 152 x 152 mm).
WEIGHT: 25 lb (11 kg).
SUPPORTING TOOLS: None.
TOOL MAINTENANCE: TBD
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing 2C6983.
FOR ALL
2C6983P08
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C6983P08
Page 2
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
PUMP HYDRAULIC - FAN REVERSER DOOR ACTUATOR
2C6983P09
PURPOSE AND USE: A portable hydraulic pump is required to pressurize the hydraulic
actuator used to open the engine fan reverser doors for access to the engine.
DESCRIPTION: This tool consists of a standard hydraulic pump modified for the
application that includes a reduced relief valve setting, a special hose with
quick disconnect fitting, hose mounting brackets, handle, tie down means, and
special marking and label. The pump has 4 mounting holes in the base to enable
the pump to be stored on fixed studs in the aircraft.
DIMENSIONS: 23 x 6 x 6 in. (584 x 152 x 152 mm).
WEIGHT: 25 lb (11 kg).
SUPPORTING TOOLS: MIL-L-7808, hold open rod.
TOOL MAINTENANCE: TBD
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing 2C6983.
FOR ALL
2C6983P09
Page 1
Dec 01/2014
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C6983P09
Page 2
Dec 01/2014
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
DELETED
2C6983P31
PURPOSE AND USE: This tool has been deleted in its entirety.
FOR ALL
2C6983P31
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FIXTURE, INSPECTION - VANE LEVER ARM - IGV THROUGH STAGE 5
2C6984G01
FOR ALL
2C6984G01
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C6984G01
Page 2
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FIXTURE, RUNOUT - FAN STATOR CASE
2C6987G03
PURPOSE AND USE: To measure both runout and radii of the stage 2 and stage 3 fan
stator case and stage 2 outer fan shroud during engine overhaul.
DESCRIPTION: The fixture basically consists of a table with a ring attached for
mounting the stage 3 fan stator case. The table incorporates a centered, bearing
mounted, vertical shaft with provisions for attaching a swing arm to measure
runouts and radii. The table also has a leveling capability.
DIMENSIONS: 50 in. dia x 30 in. (1270 mm dia x 762 mm).
WEIGHT: 300 lb (136 kg).
SUPPORTING TOOLS: None.
TOOL MAINTENANCE: Coat treated surfaces (black oxide) with corrosion
preventive light oil when stored.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: This fixture has an extensive parts list that will be of
little value without the drawing. Refer to GE Drawing 2C6987.
FOR ALL
2C6987G03
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C6987G03
Page 2
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FIXTURE, MACHINING - COMPRESSOR FRONT STATOR VANE SLOTS
2C7041G01
PURPOSE AND USE: To rework the stator vane slots of the front compressor stator.
DESCRIPTION: This fixture consists of a base plate, top locating ring, clamp
ring, post, eighteen swivel screw clamps, and sixteen strap clamps.
DIMENSIONS: 38 in. dia x 42.3 in. (965.2 mm dia x 1,074.42 mm).
WEIGHT: N/A.
SUPPORTING TOOLS: N/A.
TOOL MAINTENANCE: Apply corrosion preventive oil to all surfaces
that have black oxide finish.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing 2C7041.
FOR ALL
2C7041G01
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C7041G01
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
TOOL SET - ACTUATOR BEAM BEARING
2C7093G04
PURPOSE AND USE: To remove, install and test the plain spherical bearings of the
compressor vane actuator beam and the actuator and guide bracket.
DESCRIPTION: The tool set includes 14 swaging form blocks with three support
blocks and three pusher/pullers with three support blocks.
DIMENSIONS: 12 x 10 x 8 in. (304.8 x 254 x 203.2 mm) container.
WEIGHT: N/A.
SUPPORTING TOOLS: Not required.
TOOL MAINTENANCE: Treat coated surfaces (black oxide) with corrosion
preventive light oil when stored.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing 2C7093.
FOR ALL
2C7093G04
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C7093G04
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
ADAPTER SET, COMPRESSOR ROTOR TO ENGINE LATHE
2C7140G03
PURPOSE AND USE: To adapt the forward and rear shafts of the compressor
rotor to an engine lathe for blade tip grinding.
DESCRIPTION: A plate with adapter rings.
DIMENSIONS: 20 in. dia x 6 in. (490 mm dia x 148 mm).
WEIGHT: 120 lbs (55 kg).
SUPPORTING TOOLS: Lathe.
TOOL MAINTENANCE: Coat treated surfaces (black oxide) with corrosion
preventive light oil when stored.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS LIST
GROUP PART NO. NOMENCLATURE QUANTITY SUPPLIER
NUMBER CODE
G02 2C7140P02 Plate 1
2C7140P05 Ring 1
2C7140P06 Washer 2
2C7140P07 Ring 1
2C7140P10 Ring 1
FOR ALL
2C7140G03
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C7140G03
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FIXTURE SET, REPAIR - ACTUATOR RING SEGMENTS, COMPRESSOR STATOR
2C7224G03
FOR ALL
2C7224G03
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C7224G03
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FIXTURE, TRAVERSING - PLASMA SPRAY FAN DISK DOVETAIL SLOT
2C7312G03
PURPOSE AND USE: To automatically traverse the plasma-spray gun back and forth
across fan disk dovetail slot while depositing sprayed material on pressure faces.
DESCRIPTION: This fixture has a long metal frame resting on casters with
yokes to support the fan rotor disk. It has a traverse feed spray gun
with vane slots. There are fuses, conduit, relays, controls, thyrector
diode, connectors, electrical cabinet, safety switch, selector switches,
pilot lights, and remote controls to regulate and control operation of the
fixture. This fixture works with 115 V, 60 Hz.
DIMENSIONS: 36 x 36 x 100 in. (915 x 915 x 2,540 mm) long.
WEIGHT: 1,200 lbs (544 kg).
SUPPORTING TOOLS: Metco Plasma-Spray Mini-Gun, 5MBT, or equivalent.
TOOL MAINTENANCE: Periodic inspection and maintenance should be performed.
QUANTITY PER OPERATION: One per unit.
REPLACEMENT PARTS: This tool has an extensive parts list that will be of little
value without the drawing. Refer to GE drawing number 2C7312.
FOR ALL
2C7312G03
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C7312G03
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FIXTURE, TRAVERSING - PLASMA SPRAY FAN DISK DOVETAIL SLOT
2C7312G04
PURPOSE AND USE: To automatically traverse the plasma-spray gun back and forth
across fan disk dovetail slot while depositing sprayed material on pressure faces.
DESCRIPTION: This fixture has a long metal frame resting on casters with
yokes to support the fan rotor disk. It has a traverse feed spray gun
with vane slots. There are fuses, conduit, relays, controls, thyrector
diode, connectors, electrical cabinet, safety switch, selector switches,
pilot lights, and remote controls to regulate and control operation of the
fixture. This fixture works with 230 V, 50 Hz.
DIMENSIONS: 36 x 36 x 100 in. (915 x 915 x 2,540 mm) long.
WEIGHT: 1,200 lbs (544 kg).
SUPPORTING TOOLS: Metco Plasma-Spray Mini-Gun, 5MBT, or equivalent.
TOOL MAINTENANCE: Periodic inspection and maintenance should be performed.
QUANTITY PER OPERATION: One per unit.
REPLACEMENT PARTS: This tool has an extensive parts list that will be of little
value without the drawing. Refer to GE drawing number 2C7312.
FOR ALL
2C7312G04
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C7312G04
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FIXTURE, EXPANDER, HYDRAULIC
2C7344G08
PURPOSE AND USE: To resize combustor inner and outer liners and combustor dome.
DESCRIPTION: Segmented jaws on fixture are forced outward by a cone that is pulled
downward by a hydraulic cylinder located under the support table.
DIMENSIONS: Expander - 38 in. (955 mm) diameter x 12 in. (305 mm) high. Table
is 39 in. (990 mm) square by 36.25 in. (920 mm) high.
WEIGHT: 2700 lb (1227 kg).
SUPPORTING TOOLS: Fixture 2C7410, 2C7295, 2C7365, 2C7366, 2C7369, and 2C7334, and
Hydraulic Unit [40 tons pull force with a 6.5 in. (165 mm) stroke].
TOOL MAINTENANCE: Coat treated surfaces (black oxide) with corrosion
preventive light oil when stored.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS LIST
GROUP PART NO. NOMENCLATURE QUANTITY SUPPLIER
NUMBER CODE
G08 2C7344P04 Cone 1
2C7344P05 Plate, Locating 12
2C7344P06 Plate, Locating 12
2C7344P07 Plate, Wear 12
2C7344P08 Plate, Retaining 12
2C7344P09 Block, Spacer 12
2C7344P10 Sleeve 1
2C7344P28 Flange, Offset 1
2C7344P29 Table, Support 1
2C7344P31 Plate, Base 1
2C7344P32 Cylinder, Hydraulic 1
2C7344P33 Jaw, Expander 12
2C7344P35 Plate, Retaining 1
2C7344P37 Rod, Threaded 1
9-2032-11 Spring 12
FOR ALL
2C7344G08
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C7344G08
Page 2
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
GAGE SET, INSPECTION - COMPRESSOR STATOR VANE PLATFORM
2C7350G05
PURPOSE AND USE: To inspect the compressor stator vane platform after metal-spray.
DESCRIPTION: This gage has a steel base plate with a curved guide plate to position
the vane platform and a dial indicator to check the thickness of vane platform.
The gage is furnished with master to set "zero" on dial indicator.
DIMENSIONS: 3 x 3 x 8 in. long (75 x 75 x 200 mm) long.
WEIGHT: 25 lbs (12 kg).
SUPPORTING TOOLS: Metal-spraying equipment to deposit coating.
TOOL MAINTENANCE: Coat treated surfaces (black oxide) with
corrosion preventive light oil.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS LIST
GROUP PART NO. NOMENCLATURE QUANTITY SUPPLIER
NUMBER CODE
G05 2C7350P02 Base 1
2C7350P05 Gage, Master 1
2C7350P07 Plate, Guide 3
2C7350P14 Base 1
2C7350P15 Base 1
2C7350P16 Gage, Master 1
Model B21 Indicator, Dial with 3 AV
flat back and point,
PT229
LR-46 Lever, Mounting 3 AV
AAD-91 Bracket, Mounting 3 AV
FOR ALL
2C7350G05
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C7350G05
Page 2
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
TOOL SET, MACHINING - STAGE ONE FAN SHROUD
2C7372G04
PURPOSE AND USE: To machine the stage one fan shroud to provide clearance between
fan blades and shroud, and to cut grooves in the fan shroud.
DESCRIPTION: This tool consists of a diamond shaped tubular frame which is
bolted to the stage one fan rotor disk with 0.375-24UNF-3A x 6 in. (153
mm) long bolts. One end of the frame has the cutter and feed system and
the other end has counter weights. The disk and frame are rotated and
the cutter machines the sealing surface.
DIMENSIONS: 16 x 28 x 79 in. long (410 x 710 x 2010 mm long).
WEIGHT: 265 lb (120 kg).
SUPPORTING TOOLS: Standard hand tools.
TOOL MAINTENANCE: Periodic cleaning and lubrication is required. Periodic
sharpening of tool bit and cutter is required. Treated surfaces (black oxide)
to be coated with corrosion preventive light oil when stored.
QUANTITY PER OPERATION: One set.
REPLACEMENT PARTS LIST
GROUP PART NO. NOMENCLATURE QUANTITY SUPPLIER
NUMBER CODE
G04 2C7372P03 Counter Weight 10
2C7372P04 Counter Weight 11
2C7372P10 Tool Bit 1
2C7372P11 Tool Holder 1
2C7372P16 T-Bolt 2
2C7372P17 Compound Slide 1
2C7372P18 Hex Bolt 1
Pad 1
2C7372P20
Frame 1
2C7372P43
2C7372P44 Adapter Plate 1
2C7372P48 Threaded Stud 2
FOR ALL
2C7372G04
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C7372G04
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FIXTURE, WATERFLOW - STAGE 1 AND 2 HIGH PRESSURE TURBINE ROTOR BLADES
2C7376G03
PURPOSE AND USE: To waterflow check stage 1 and 2 high pressure turbine rotor
blades for obstructions in the cooling air passages.
DESCRIPTION: This fixture consists of a special nozzle and nipple that have rubber
sealing pads. The nozzle and nipple are used with a lever operated blow gun.
DIMENSIONS: 3 x 4 x 6 in. (76 x 102 x 152 mm).
WEIGHT: 2 lbs (1 kg).
SUPPORTING TOOLS: Waterflow Shield, 2C6569.
TOOL MAINTENANCE: None required.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS LIST
GROUP PART NO. NOMENCLATURE QUANTITY SUPPLIER
NUMBER CODE
G03 2C7376P03 Counter Weight 1
421-0402 Counter Weight 1
No. 8785W Tool Bit 1 DG
No. 474 Tool Holder 1 DG
FOR ALL
2C7376G03
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C7376G03
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FIXTURE, WATERFLOW - STAGE 2 NOZZLE HIGH PRESSURE TURBINE STATOR
2C7379G03
PURPOSE AND USE: To inspect cooling air holes to ensure that air holes are
not blocked and that air flow requirements are met.
DESCRIPTION: This fixture holds nozzle segment between two gasketed
pads and supplies air pressure to the internal passages to check flow
through the HPT nozzle segment.
DIMENSIONS: 16 x 14 x 10 in. (406 x 356 x 254 mm).
WEIGHT: 25 lb (11 kg)
SUPPORTING TOOLS: Regulated water supply.
TOOL MAINTENANCE: None.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: This tool has an extensive parts list that will be of little
value without the drawing. Refer to GE drawing number 2C7379.
FOR ALL
2C7379G03
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C7379G03
Page 2
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FIXTURE, INSPECTION/MACHINING - THERMAL SHIELD HIGH PRESSURE TURBINE ROTOR
2C7411G03
PURPOSE AND USE: To inspect and machine either the forward or aft flanges
and seals of the HPT rotor thermal shield.
DESCRIPTION: This fixture is a heavy steel plate machined on both sides with
capscrews to hold the thermal shield down on the fixture's rabbets. One side
is for the forward flange and the other side is for the aft flange.
DIMENSIONS: 28 in. (711 mm) dia x 0.375 in. (9.5 mm) thick.
WEIGHT: 30 lbs (14 kg).
SUPPORTING TOOLS: None.
TOOL MAINTENANCE: Coat fixture with light oil when not in use.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS LIST
GROUP PART NO. NOMENCLATURE QUANTITY SUPPLIER
NUMBER CODE
G03 2C7411P03 Washer 20
2C7411P07 Ring 1
0.3125 x 0.75 LG Scr, Soc, Hd Cap 20
0.250 x 1.5 LG Scr, Soc, Hd Cap 37
FOR ALL
2C7411G03
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C7411G03
Page 2
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FIXTURE SET, SHOT PEENING - COMPRESSOR ROTOR BLADE DOVETAIL
2C7423G04
PURPOSE AND USE: To provide holding, masking and almen strip holding
facilities for shot peening the dovetail on the compressor rotor blades
stages 1 thru 14 (all blades).
DESCRIPTION: The fixture set includes stages 1 thru 14 boots, boot retainers,
rubber pads, almen strip retainers, and a spring clip.
DIMENSIONS: N/A.
WEIGHT: N/A.
SUPPORTING TOOLS: Adapter sleeve (customer-supplied), air blast machine.
TOOL MAINTENANCE: Apply corrosion preventive oil to all surfaces
that have black oxide finish.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing 2C7423.
FOR ALL
2C7423G04
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C7423G04
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FIXTURE, DRILL AND REAM-RING SEGMENT, COMPRESSOR STATOR - STAGES 5 AND 6
2C7425G01
PURPOSE AND USE: To drill and ream the stages 5 and 6 of the compressor
stator ring segments during rework.
DESCRIPTION: The fixture consists of an aluminum base plate with mounting block
and clamps, drilling block, slide, and two locating pins.
DIMENSIONS: 14 x 18 x 6 in. (355.6 x 457.2 x 152.4 mm).
WEIGHT: N/A.
SUPPORTING TOOLS: N/A.
TOOL MAINTENANCE: Apply corrosion preventive oil to all surfaces
that have black oxide finish.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing 2C7425.
FOR ALL
2C7425G01
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C7425G01
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FIXTURE, STAGE 1 FAN BLADE LEADING EDGE
2C7546G11
PURPOSE AND USE: To contour the leading edge of the convex side
of the stage 1 fan blade.
DESCRIPTION: This fixture consists of a rigid frame and cabinet, motor driven
abrasive wheel, six guide rollers, cam and titanium ignitor assembly. The
abrasive wheel is mounted to the cabinet through two guide rails and is
driven by a 60 Hz. motor utilizing V-belts.
DIMENSIONS: 52 x 60 x 26 in. (1,321 x 1,524 x 660 mm).
WEIGHT: 1,250 lbs (567 kg).
SUPPORTING TOOLS: Optical profile Projector.
TOOL MAINTENANCE: Coat surfaces (black oxide) with corrosion
preventive light oil when stored.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: This fixture has an extensive Parts List that will be of
little value without the drawing. Refer to GE drawing 2C7546.
FOR ALL
2C7546G11
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C7546G11
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FIXTURE, STAGE 1 FAN BLADE LEADING EDGE
2C7546G12
PURPOSE AND USE: To contour the leading edge of the convex side
of the stage 1 fan blade.
DESCRIPTION: This fixture consists of a rigid frame and cabinet, motor driven
abrasive wheel, six guide rollers, cam and titanium ignitor assembly. The
abrasive wheel is mounted to the cabinet through two guide rails and is
driven by a 50 Hz. motor utilizing V-belts.
DIMENSIONS: 52 x 60 x 26 in. (1,321 x 1,524 x 660 mm).
WEIGHT: 1,250 lbs (567 kg).
SUPPORTING TOOLS: Optical profile projector.
TOOL MAINTENANCE: Coat surfaces (black oxide) with corrosion
preventive light oil when stored.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: This fixture has an extensive Parts List that will be of
little value without the drawing. Refer to GE drawing 2C7546.
FOR ALL
2C7546G12
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C7546G12
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FIXTURE, COMPRESSOR ROTOR BLADE LENGTH GAGE
2C7549G06
PURPOSE AND USE: To measure the length of the compressor rotor blades.
DESCRIPTION: This fixture seats the blade on its pressure surfaces and a dial
indicator indicates its length compared to the set master.
DIMENSIONS: 26 x 10 x 10 in. (660 x 255 x 255 mm).
WEIGHT: 78 lb (35 kg).
SUPPORTING TOOLS: None required.
TOOL MAINTENANCE: Apply a light coat of oil to all surfaces when stored.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: This fixture has an extensive parts list that will be of little
value without the drawing. Refer to GE Drawing No. 2C7549.
FOR ALL
2C7549G06
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C7549G06
Page 2
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FIXTURE, HOLDING - HIGH PRESSURE TURBINE ROTOR BLADE - STAGES 1 AND 2
2C7613G01
PURPOSE AND USE: To X-ray the high pressure turbine rotor blades
for contamination inspection.
DESCRIPTION: This fixture includes a PVC plastic frame with six blade
holders, operated by belt-driven sprockets.
DIMENSIONS: 8.5 x 20.5 x 11 in. (215.9 x 520.7 x 279.4 mm).
WEIGHT: N/A.
SUPPORTING TOOLS: N/A.
TOOL MAINTENANCE: Apply corrosion preventive oil to all surfaces
that have black oxide finish.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing 2C7613.
FOR ALL
2C7613G01
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C7613G01
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FIXTURE SET, SHOT PEENING - HIGH PRESSURE TURBINE ROTOR BLADE DOVETAILS
2C7614G05
PURPOSE AND USE: The Shot Peening Fixture Set is used to hold the high pressure
turbine rotor (HPTR) blades and the almen strip during shot peening.
DESCRIPTION: The Shot Peening Fixture Set consists of two molded rubber masks, three
almen strip holders, three almen strip blocks (black oxide) and one holder block.
DIMENSIONS: TBD
WEIGHT: 13 lb (6 kg).
SUPPORTING TOOLS: No. 613 Peenmatic Shot Peen Machine, Planetary Table.
TOOL MAINTENANCE: Apply corrosion preventive oil to all surfaces
that have a black oxide finish.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing 2C7614.
FOR ALL
2C7614G05
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C7614G05
Page 2
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FORM TOOL SET, DOVETAIL SLOT REWORK - COMPRESSOR ROTOR
2C7690G07
PURPOSE AND USE: To machine out fretted material of dovetail pressure faces
at stages 3 thru 9 of the compressor rotor spool.
DESCRIPTION: This fixture includes 14 left-hand and right-hand form tools with steel
shanks and carbide tips, used for stages 3 thru 9 of the compressor rotor spool.
DIMENSIONS: 6.0 x 0.8 x 1.0 in. (152.4 x 20.32 x 25.4 mm).
WEIGHT: N/A.
SUPPORTING TOOLS: N/A.
TOOL MAINTENANCE: Apply corrosion preventive oil to all surfaces
that have black oxide finish.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing 2C7690.
FOR ALL
2C7690G07
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C7690G07
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
CONTOUR MASTER, FAN BLADE LEADING EDGE, SECTION KK
2C7734P01
PURPOSE AND USE: This is a 20x precision, contour master that is used with the stage
1 fan blade rework machine P/N 2C7546 and herald blade edge projector.
DESCRIPTION: 20x contour master glassine transparency of fan blade leading edge.
DIMENSIONS: N/A.
WEIGHT: N/A.
SUPPORTING TOOLS: 2C7546, stage 1 fan blade leading edge fixture
and optical profile projector.
TOOL MAINTENANCE: Not required.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing 2C7734.
FOR ALL
2C7734P01
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C7734P01
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FIXTURE, MACHINING - STAGE 1 HIGH PRESSURE COMPRESSOR BLADE TIP
2C7799G01
PURPOSE AND USE: To locate and hold the blade for the machining of the
squealer tip following weld build-up.
DESCRIPTION: This fixture consists of a base plate platform, support, pivot
plate, two slide plates, cradle block, four guards, an indicator, stop, roller,
counterweight, and adapter. The cradle block holds the blade.
DIMENSIONS: 13.8 x 10.4 x 16 in. (350.52 x 264.16 x 406.4 mm).
WEIGHT: N/A.
SUPPORTING TOOLS: N/A.
TOOL MAINTENANCE: Apply corrosion preventive oil to all surfaces
that have black oxide finish.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing 2C7799.
FOR ALL
2C7799G01
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C7799G01
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
GAGE SET, LENGTH - COMPRESSOR STATOR VANE
2C7842G09
PURPOSE AND USE: The Length Gage Set is used to measure the length
of the compressor stator vanes.
DESCRIPTION: The Length Gage Set consists of a base, post, dial indicator,
holder, locator blocks, locators, and set masters. A container is supplied.
The G09 version of 2C7842 is used for SB 72-0475, Phase II Aero vanes. The
tool has a black oxide or black phosphate finish.
DIMENSIONS: 10 x 12 x 24 in. (254 x 305 x 610 mm).
WEIGHT: 20 lbs (9 kg).
SUPPORTING TOOLS: None.
TOOL MAINTENANCE: Apply corrosion preventive oil to all surfaces that
have black oxide or black phosphate coating.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing 2C7842.
FOR ALL
2C7842G09
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C7842G09
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
GAGE SET, LENGTH - COMPRESSOR STATOR VANE
2C7842G10
PURPOSE AND USE: The Length Gage Set is used to measure the length
of the compressor stator vanes.
DESCRIPTION: The Length Gage Set consists of a base, post, dial indicator,
holder, locator blocks, locators, and set masters. A container is supplied.
The G10 version of 2C7824 is used for Pre SB 72-0475, Phase O/I Aero vanes.
The tool has a black oxide or black phosphate finish.
DIMENSIONS: 10 x 12 x 24 in. (254 x 305 x 610 mm).
WEIGHT: 20 lbs (9 kg).
SUPPORTING TOOLS: None.
TOOL MAINTENANCE: Apply corrosion preventive oil to all surfaces that
have black oxide or black phosphate coating.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing 2C7842.
FOR ALL
2C7842G10
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C7842G10
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
STAND, BACKFLUSH, HIGH PRESSURE TURBINE ROTOR BLADES
2C7866G01
PURPOSE AND USE: To flush out foreign particles from HPT blade air
passages, which may become contaminated during overhaul. This stand
operates on either 50 or 60 Hz power.
DESCRIPTION: This stand consists primarily of a reservoir, water pump, filter,
air/water mixer, blade adapters, and spray chamber. The blades are backflushed by
forcing the water/air mixture through the holes in the airfoil, into the internal
passages and out the holes in the base of the blade dovetail. An air/water
mixture is used to ensure that a turbulent flow condition exists.
DIMENSIONS: 66 x 63 x 54 in. (1676 x 1600 x 1372 mm).
WEIGHT: 500 lb (227 kg).
SUPPORTING TOOLS: Use with 2C7877 HPT blades backflush seal.
TOOL MAINTENANCE: If water pressure drops below 25 psi, change the
filters (50 micron, Qty 8, Filterchem, Alhambra, California 71803).
Change water at least weekly.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: This stand has an extensive Parts List that will be of little
value without the drawing. Refer to GE drawing 2C7866.
FOR ALL
2C7866G01
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C7866G01
Page 2
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
SEAL, BACKFLUSH, HPT BLADES - STAGE 1
2C7877P05
PURPOSE AND USE: To ensure that the backflushing water enters the airfoil
holes and exits the dovetail cooling holes.
DESCRIPTION: The seal is made of silicon rubber.
DIMENSIONS: 11 x 3 x 3 in. (279 x 76 x 76 mm).
WEIGHT: 25 lbs (11 kg).
SUPPORTING TOOLS: 2C27866 Backflush Stand.
TOOL MAINTENANCE: None required.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Molds for producing these seals are the property
of GE and can be borrowed from GE.
FOR ALL
2C7877P05
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C7877P05
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
SEAL, BACKFLUSH, HPT BLADES - STAGE 2
2C7877P06
PURPOSE AND USE: To ensure that the backflushing water enters the airfoil
holes and exits the dovetail cooling holes.
DESCRIPTION: The seal is made of silicon rubber.
DIMENSIONS: 11 x 3 x 3 in. (279 x 76 x 76 mm).
WEIGHT: 25 lbs (11 kg).
SUPPORTING TOOLS: 2C27866 Backflush Stand.
TOOL MAINTENANCE: None required.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Molds for producing these seals are the property
of GE and can be borrowed from GE.
FOR ALL
2C7877P06
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C7877P06
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
TOOL SET, REPLACEMENT - ACTUATOR BEAM BEARING
2C7895G02
PURPOSE AND USE: To install, remove, swage and load test the slot-loaded bearings
of the front compressor stator vane actuation system.
DESCRIPTION: The tool set consists of the necessary punches, dies, adapters, and
washers to install, remove, swage and load test slot loaded bearings.
DIMENSIONS: 24 x 24 x 6 in. (610 x 610 x 152 mm).
WEIGHT: 20 lb (9 kg).
SUPPORTING TOOLS: Arbor press.
TOOL MAINTENANCE: Coat black oxided surfaces with corrosion preventive light oil.
QUANTITY PER OPERATION: One set.
REPLACEMENT PARTS LIST
GROUP PART NO. NOMENCLATURE QUANTITY SUPPLIER
NUMBER CODE
G02 2C7895P02 Punch, Seating 1
2C7895P03 Punch, Seating 1
2C7895P05 Die, Seating 1
2C7895P06 Die, Seating 1
2C7895P09 Adapter, Seating 1
2C7895P10 Adapter, Seating 1
2C7895P12 Punch, Swaging 1
2C7895P13 Punch, Swaging 1
2C7895P14 Punch, Swaging 1
2C7895P18 Punch, Swaging 1
2C7895P19 Punch, Swaging 1
2C7895P20 Die, Swaging 1
2C7895P22 Die, Swaging 1
2C7895P23 Container 1
FOR ALL
2C7895G02
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C7895G02
Page 2
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FIXTURE, PREHEAT WELDING - HIGH PRESSURE TURBINE BLADE
2C7897G01
PURPOSE AND USE: To pre-heat the area of the blade to be repaired to 1800-
2000°F (982-1093°C) in an argon atmosphere.
DESCRIPTION: The tool consists of two quartz line heaters that produce a heat zone
on the airfoil. The aluminum heater housings are water cooled and the quartz
elements are air cooled. Between the heaters is a chamber for mounting the blade,
adjusting the blade height, and providing an argon atmosphere for welding.
DIMENSIONS: 24 x 12 x 12 in. (610 x 305 x 305 mm).
WEIGHT: 40 lb (18 kg).
SUPPORTING TOOLS: Variac, 90 psi (621 kPa) filtered air, 0.2 gpm
(0.85 1/min) water, argon gas.
TOOL MAINTENANCE: None.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: See GE drawing 2C7897.
FOR ALL
2C7897G01
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C7897G01
Page 2
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FIXTURE, GRIND - SEAL LIP, HIGH PRESSURE TURBINE BLADES
2C7898G01
PURPOSE AND USE: This fixture is used to grind the seal lip (outer diameter and
inner diameter) to obtain required contour following deep weld repair.
DESCRIPTION: This fixture consists of an arm, arm extension, clamp block,
clamp jaw, base, slide plate, two bumpers, knurled knob, and revolving
handle. The clamp for the blade dovetail is mounted on the arm, which is
manually pivoted on top of the slide plate.
DIMENSIONS: 17.75 x 6.75 x 5.7 in. (450.85 x 171.45 x 144.78 mm).
WEIGHT: N/A.
SUPPORTING TOOLS: N/A.
TOOL MAINTENANCE: Apply corrosion preventive oil to all surfaces
that have black oxide finish.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing 2C7898.
FOR ALL
2C7898G01
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C7898G01
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FIXTURE, FLUSH - STAGE 2 HIGH PRESSURE TURBINE BLADE
2C7902G01
PURPOSE AND USE: To seal the high pressure turbine root holes during operation.
DESCRIPTION: This fixture consists of a silicone rubber block fitted to the
blade dovetail, with a threaded steel insert in the base.
DIMENSIONS: 1.25 x 2.38 x 1.38 in. (31.75 x 60.45 x 35.05 mm).
WEIGHT: N/A.
SUPPORTING TOOLS: N/A.
TOOL MAINTENANCE: Not required.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing 2C7902.
FOR ALL
2C7902G01
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C7902G01
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FIXTURE, FLUSH - STAGE 1 HIGH PRESSURE TURBINE BLADE
2C7903G01
PURPOSE AND USE: To seal the high pressure turbine blades root holes
during force flush operation.
DESCRIPTION: This fixture consists of a silicone rubber block fitted to the
blade dovetail, with a threaded steel insert in the base.
DIMENSIONS: 1.25 x 2.0 x 1.38 in. (31.75 x 50.8 x 35.05 mm).
WEIGHT: N/A.
SUPPORTING TOOLS: N/A.
TOOL MAINTENANCE: Not Required.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing 2C7903.
FOR ALL
2C7903G01
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C7903G01
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FIXTURE, REMOVAL - FAIRING, FAN STATOR
2C8008G01
FOR ALL
2C8008G01
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C8008G01
Page 2
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
GAGE, SIGHT - VARIABLE STATOR VANE - STAGES 5 AND 6
2C8016G02
PURPOSE AND USE: The Sight Gage is used to do a visual inspection of the stage
5 and stage 6 vane actuation arms of the compressor.
DESCRIPTION: The Sight Gage consists of matched half cylinders with tangs
to fit over the assembled vane lever and a spacer to engage the slots in
the vane lever. A Plexiglas indicator block mounts on top of the base. The
tool has a black oxide or black phosphate finish.
DIMENSIONS: 3 x 3 x 3 in. (76 x 76 x 76 mm).
WEIGHT: 1 lb (0.5 kg).
SUPPORTING TOOLS: None.
TOOL MAINTENANCE: Apply corrosion preventive oil to all surfaces
that have a black oxide finish.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing 2C8016.
FOR ALL
2C8016G02
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C8016G02
Page 2
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
EROM, COMPRESSOR ROTOR LASER MIKE
2C8017P08
PURPOSE AND USE: The Compressor Rotor Laser Mike Erom (Laser Mike) is used
to measure the compressor rotor and spool diameter.
DESCRIPTION: The Laser Mike is laser equipment used with Compressor
Rotor Erom Fixture, 2C8018.
DIMENSIONS: 66.2 x 12.8 x 9.5 in. (1681 x 325 x 241 mm).
WEIGHT: TBD
SUPPORTING TOOLS: 2C8018.
TOOL MAINTENANCE: TBD
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing 2C8017.
FOR ALL
2C8017P08
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C8017P08
Page 2
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FIXTURE, LIFT - COMPRESSOR ROTOR DISKS, STAGE 2, 10, AND 14
2C8019G01
PURPOSE AND USE: To lift and hold compressor rotor disks while heated
for installation and removal.
DESCRIPTION: Consists of spider with three knurled nuts and expanding
holding blocks for lifting the rotor disks.
DIMENSIONS: 12 x 12 x 5 in. (305 x 305 x 125 mm).
WEIGHT: 11 lbs (5 kg).
SUPPORTING TOOLS: Hoist.
TOOL MAINTENANCE: Coat treated surfaces (black oxide) with corrosion
preventive light oil when stored. Load test periodically (see GE drawing
2C8019 for load test diagram and applicable NOTE).
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS LIST
GROUP PART NO. NOMENCLATURE QUANTITY SUPPLIER
NUMBER CODE
G01 2C8019P02 Spider 1
2C8019P03 Holding Block 3
28105 Knurled Nut 3 F
0.5x3.25 Nut Ring Bolt 1 AB
FOR ALL
2C8019G01
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C8019G01
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
TOOL SET, WEDGING - COMPRESSOR ROTOR BLADES
2C8042G08
PURPOSE AND USE: The Wedging Tool Set is used to lock the compressor
rotor blades outward to grind the blade tip.
DESCRIPTION: The Wedging Tool Set consists of 24 locking lugs with screws
and nuts to wedge and lock the blades outward when grinding the blade
tips. The primary color of the tool is purple.
DIMENSIONS: 16 x 4 x 4 in. (406 x 102 x 102 mm).
WEIGHT: 5 lb (2 kg).
SUPPORTING TOOLS: Compressor Blade Tip Grinding Fixture.
TOOL MAINTENANCE: None.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing 2C8042.
FOR ALL
2C8042G08
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C8042G08
Page 2
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
CLEANING KIT, ENGINE - COKE
2C8043G02
PURPOSE AND USE: The Engine Cleaning Kit is used to spray abrasive media
into the engine to clean the compressor.
DESCRIPTION: The Engine Cleaning Kit consists of an upright hopper-like cylinder
on wheels, a two-piece wand, and a connecting hose.
DIMENSIONS: Cylinder, 10 x 24 in. (254 x 610 mm). Wand, 1 x
72 in. (25.4 x 1829 mm).
WEIGHT: 75 lb (34 kg).
SUPPORTING TOOLS: Dry shop air or nitrogen, Jet Shot Powdered Coke 20 Mesh of
Less Carbon Sand L340. Refer to GE Specification D50TF-Sl.
TOOL MAINTENANCE: TBD
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing 2C8043.
FOR ALL
2C8043G02
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C8043G02
Page 2
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
GO/NO GO GAGE, SPLINE WEAR - HORIZONTAL DRIVE SHAFT, IGB
2C8055G01
PURPOSE AND USE: To inspect spline wear, maximum wear limit 0.015 in. (0.38
mm), on inlet gearbox gearshaft assembly.
DESCRIPTION: Gage body with handle.
DIMENSIONS: 4 x 4 x 8 in. (102 x 102 x 203 mm) for case.
WEIGHT: 3 lbs (1.4 kg).
SUPPORTING TOOLS: None required.
TOOL MAINTENANCE: None required.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS LIST
GROUP PART NO. NOMENCLATURE QUANTITY SUPPLIER
NUMBER CODE
G01 2C8055P02 Gage 1
2C8055P03 Container 1
FOR ALL
2C8055G01
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C8055G01
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
GO/NO GO GAGE, SPLINE WEAR - HORIZONTAL DRIVE SHAFT IGB
2C8062G02
PURPOSE AND USE: The Spline Wear Go/No Go Gage is used to make an inspection
of the wear, maximum limit 0.030 in (0.76 mm), on the forward end of the
horizontal drive shaft of the inlet gearbox assembly.
DESCRIPTION: The Spline Wear Go/No Go Gage is a piece of carbide,
ground with a closely controlled tab and two triangular points. The
tool has a nickel plate finish.
DIMENSIONS: 8 x 4 x 4 in. (203 x 102 x 102 mm) for case.
WEIGHT: 3 lbs (1 kg).
SUPPORTING TOOLS: Optical Comparator.
TOOL MAINTENANCE: None.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing 2C8062.
FOR ALL
2C8062G02
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C8062G02
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
GO/NO GO GAGE, INSPECT SPLINED ADAPTER 0.015
2C8063G01
PURPOSE AND USE: To inspect spline wear, maximum limit 0.015 in. (0.38
mm), on compressor rotor splined adapter.
DESCRIPTION: The gage consists of a piece of carbide ground with a closely
controlled tag and two triangular points. The tab width equals the chordal
dimension of the space between two adjacent teeth plus the maximum wear tolerance
of 0.015 inch (0.4 mm). If the wear is at or exceeds the maximum tolerance, the
triangular points will not touch the major diameter. A container is furnished.
DIMENSIONS: 4 x 4 x 8 in. (102 x 102 x 203 mm) for case.
WEIGHT: 3 lbs (1.4 kg).
SUPPORTING TOOLS: None.
TOOL MAINTENANCE: TBD
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS LIST
GROUP PART NO. NOMENCLATURE QUANTITY SUPPLIER
NUMBER CODE
G01 2C8063P02 Gage 1
2C8063P03 Container 1
FOR ALL
2C8063G01
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C8063G01
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
GO/NO GO GAGE, INSPECT - SPLINED ADAPTER
2C8064G02
PURPOSE AND USE: The Inspect Go/No Go Gage is used to make an inspection of the wear
of the muff spline (where the forward end of the horizontal drive shaft touches)
on heavy maintenance units, maximum wear limit 0.030 in. (0.76 mm).
DESCRIPTION: The Inspect Go/No Go Gage is a steel handle attached to a
gage that is made from tool blank No. K1210.
DIMENSIONS: Container, 8 x 4 x 4 in. (203 x 102 x 102 mm) for case.
WEIGHT: 3 lbs (1 kg).
SUPPORTING TOOLS: Optical Comparator.
TOOL MAINTENANCE: None.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing 2C8064.
FOR ALL
2C8064G02
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C8064G02
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FIXTURE, PRELOAD - SPACER STAGE 1 FAN BLADE
2C8073G05
PURPOSE AND USE: The Preload Fixture is used to remove and install
stage 1 fan blade retainer key.
DESCRIPTION: The Preload Fixture consists of a handle, blade yoke, preload
yoke and an eight pitch quadruple thread stud and nut. The handle and
handle nut are coated with green plastisol.
DIMENSIONS: 15 x 6 x 3 in. (381 x 152 x 76 mm).
WEIGHT: 3 lb (1 kg).
SUPPORTING TOOLS: None.
TOOL MAINTENANCE: Apply corrosion preventive oil to all surfaces that
have black oxide or black phosphate coating.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing 2C8073.
FOR ALL
2C8073G05
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C8073G05
Page 2
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
DELETED
2C8082G01
PURPOSE AND USE: This tool has been deleted in its entirety.
FOR ALL
2C8082G01
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FIXTURE, GRIND/INSPECT - COMPRESSOR ROTOR
2C8087G04
FOR ALL
2C8087G04
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C8087G04
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
ADAPTER, GRINDING - HP TURBINE ROTOR
2C8094G04
PURPOSE AND USE: To adapt HP turbine rotor blade tip grinding on 2C8087
compressor rotor grinding fixture.
DESCRIPTION: Consists of a shaft, axial locator, dummy races, etc. which
adapt the HP turbine rotor to the 2C8087G03 grind fixture. All is secured
in a stand. Lift eyes are provided.
DIMENSIONS: Stand - 50 x 50 x 90 in. (1270 x 1270 x 2290 mm).
WEIGHT: 450 lb (204 kg).
SUPPORTING TOOLS: 2C8087.
TOOL MAINTENANCE: Coat treated surfaces (black oxide or black phosphate)
with corrosion preventive light oil. Load test periodically (see GE drawing
2C8094 for load test diagram and applicable NOTE).
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: This Grinding Adapter has an extensive Parts List that will be
of little value without the drawing. Refer to GE drawing 2C8094.
FOR ALL
2C8094G04
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C8094G04
Page 2
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
STANDARD - KNOWN DEFECT FLUORESCENT PENETRANT INSPECTION
2C8095G01
FOR ALL
2C8095G01
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C8095G01
Page 2
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FIXTURE, TORQUE MEASURING - VARIABLE STATOR VANE ASSEMBLY
2C8102G02
PURPOSE AND USE: The Torque Measuring Fixture is used to measure the torque required
to actuate the half rings and vanes of each stage of the variable stators.
DESCRIPTION: The Torque Measuring Fixture consists of six drive adapters, six
locator plugs, and six adapters. A container is also supplied.
DIMENSIONS: 24 x 5 x 2 in. (610 x 127 x 51 mm).
WEIGHT: 4 lb (2 kg).
SUPPORTING TOOLS: 3/8 in. Drive Torque Wrench.
TOOL MAINTENANCE: Apply corrosion preventive oil to all surfaces that
have black oxide or black phosphate coating.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing 2C8102.
FOR ALL
2C8102G02
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C8102G02
Page 2
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FIXTURE, RUNOUT, MEASUREMENT - FAN BOOSTER ROTOR ASSEMBLY
2C8113G03
PURPOSE AND USE: The Runout Measurement Fixture is used to measure the
runout and actual radii of the fan booster blades.
DESCRIPTION: The Runout Measurement Fixture consists of a steel base, pedestal,
rotary table, and an indicator gage. The primary color of the tool is blue.
DIMENSIONS: 46 x 22 x 22 in. (1168 x 559 x 559 mm).
WEIGHT: 1800 lb (816 kg).
SUPPORTING TOOLS: 2C14686.
TOOL MAINTENANCE: Clean the bushings at regular intervals with the brush that
is included with the tool. Apply corrosion preventive oil to all surfaces
that have black oxide or black phosphate coating.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing 2C8113.
FOR ALL
2C8113G03
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C8113G03
Page 2
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
DELETED
2C14011P02
PURPOSE AND USE: This tool has been deleted in its entirety.
Superseded by tool 2C14011P03.
FOR ALL
2C14011P02
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FIXTURE, BUILDUP, HPT ROTOR
2C14011P03
PURPOSE AND USE: This tool is used to hold high pressure turbine rotor
during buildup and runout check.
DESCRIPTION: The fixture is a single-piece item which has holes to mount
it to a rotary table. At the top of the fixture there is a checking
diameter which engages with the turbine rotor. Tapped holes are provided
to fasten the rotor to the fixture.
DIMENSIONS: 14.5 in. dia x 4 in. (370 mm. dia x 100 mm).
WEIGHT: 90 lbs (41 kg).
SUPPORTING TOOLS: Rotab, Ultraron UR-18-00005-1 or equivalent.
TOOL MAINTENANCE: Apply a light coat of oil on all surfaces when stored.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: None required.
FOR ALL
2C14011P03
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C14011P03
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FIXTURE, LIFT AND TURN - COMPRESSOR ROTOR AFT
2C14014G01
PURPOSE AND USE: To lift the compressor rotor in the vertical position, forward
end down, translate to the vertical position, aft end down.
DESCRIPTION: Consists of a cap, an arm, a clevis, and a pin. The cap threads on the
aft end of the rotor. A clevis is attached to the cap to provide a linkage for the
arm and to allow the swivel motion. A pin attaches the arm to the clevis.
DIMENSIONS: 8 in. dia x 26.5 in. (205 mm dia x 675 mm).
WEIGHT: 35 lb (16 kg).
SUPPORTING TOOLS: Overhead Hoist.
TOOL MAINTENANCE: Coat treated surfaces (black oxide or black phosphate)
with corrosion preventive light oil when stored. Load test periodically
(see GE drawing 2C14014 for load test diagram).
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS LIST
GROUP PART NO. NOMENCLATURE QUANTITY SUPPLIER
NUMBER CODE
G01 2C14014P02 Cap 1
2C14014P03 Arm 1
2C14014P04 Clevis 1
BLS10TA34SL8 Ball-Lok Pin 1
FOR ALL
2C14014G01
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C14014G01
Page 2
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
BRACKET SET - COMPRESSOR REAR FRAME TO SUBASSEMBLY STAND
2C14015G05
PURPOSE AND USE: The Bracket Set is used to support the compressor
rear frame in a subassembly stand.
DESCRIPTION: The Bracket Set consists of two plates welded to the ends
of a pipe with an adapter bracket welded laterally to the pipe. The
primary color of the tool is blue.
DIMENSIONS: 8 x 17 x 24 in. (203 x 432 x 610 mm).
WEIGHT: 25 lbs (11 kg).
SUPPORTING TOOLS: 2C14227 subassembly dolly.
TOOL MAINTENANCE: Apply corrosion preventive oil to all surfaces that
have black oxide or black phosphate coating.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing 2C14015.
FOR ALL
2C14015G05
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C14015G05
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
PUSHER SET, RACES AND SEALS - HIGH PRESSURE TURBINE ROTOR STAGE 1
2C14025G05
PURPOSE AND USE: The Races and Seals Pusher Set is used to hold various
engine parts against mating parts after being heated during assembly of the
high pressure turbine (HPT) rotor stage 1 disk.
DESCRIPTION: The Pusher Set consists of one internally threaded steel ring,
with 0.5 in. (13 mm) square female drive lugs and a puller plate assembly.
The tool has a black oxide or black phosphate finish.
DIMENSIONS: 29 x 16 x 8 in. (737 x 406 x 203 mm).
WEIGHT: 45 lb (20 kg).
SUPPORTING TOOLS: 1/2 in. square Drive Wrench.
TOOL MAINTENANCE: Apply corrosion preventive oil to all surfaces that
have black oxide or black phosphate coating.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing 2C14025.
FOR ALL
2C14025G05
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C14025G05
Page 2
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
DELETED
2C14027G02
PURPOSE AND USE: This tool has been deleted in its entirety.
FOR ALL
2C14027G02
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
PUSHER, INSTALL - HIGH PRESSURE TURBINE ROTOR
2C14028G01
PURPOSE AND USE: This tool is used to seat the high pressure turbine (HPT)
rotor on the compressor rotor aft shaft.
DESCRIPTION: The Pusher Install consists of a circular adapter with an internal
spline and a torque plate. The inside of the adapter is coated with plastisol.
The tool has a black phosphate or black oxide finish.
DIMENSIONS: 8 x 7 x 7 in. (203 x 178 x 178 mm).
WEIGHT: 7 lbs (3.2 kg).
SUPPORTING TOOLS: 2C14040, and SWE 8100 or 8108.
TOOL MAINTENANCE: Apply corrosion preventive oil to all surfaces that
have black oxide or black phosphate coating.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing 2C14028.
FOR ALL
2C14028G01
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C14028G01
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
DELETED
2C14028G02
PURPOSE AND USE: This tool has been deleted in its entirety.
FOR ALL
2C14028G02
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
PULLER, LOW PRESSURE TURBINE MODULE
2C14029G04
PURPOSE AND USE: The Low Pressure Turbine Module Puller is used to pull the
low pressure turbine/module from the low pressure midshaft.
DESCRIPTION: The Low Pressure Turbine Module Puller consists of a long
pusher tube with a hydraulic cylinder that is mounted in a nut. The tool
has a black oxide or black phosphate finish.
DIMENSIONS: 7.5 x 36 in. (191 x 914 mm).
WEIGHT: 75 lb (34 kg).
SUPPORTING TOOLS: Hydraulic Hand Pump, 2C14052, 2C14602.
TOOL MAINTENANCE: Apply corrosion preventive oil to all surfaces that
have black oxide or black phosphate coating.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing 2C14029.
FOR ALL
2C14029G04
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C14029G04
Page 2
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FIXTURE, LIFT AND TURN - CORE MODULE, AFT
2C14030G04
PURPOSE AND USE: To lift and rotate aft end of core engine from vertical
to horizontal position and vice versa.
DESCRIPTION: The 3000 lb (1364 kg) capacity lift fixture consists of a lift
beam with a hoisting attachment to which is attached two lifting cables. The
cables are attached to a lifting ring configured to interface with the compressor
rear frame, with the high pressure turbine (HPT) rotor, and HPT stator support
removed, or with the HPT stator support, shroud support, and the HPT rotor
installed. Attachment is made with bolts and nuts.
DIMENSIONS: 39 in. dia x 6 in. (990 mm dia x 150 mm).
WEIGHT: 125 lb (57 kg).
SUPPORTING TOOLS: Hoist and Fixture, Lift - Core Module Forward (To be supplied).
TOOL MAINTENANCE: Coat treated surfaces (black oxide or black phosphate) with
corrosion preventive light oil when stored. Load test periodically (see GE
drawing 2C14030 for load test diagram and applicable NOTE).
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS LIST
GROUP PART NO. NOMENCLATURE QUANTITY SUPPLIER
NUMBER CODE
G04 2C14030P18 Dummy Support - HPT 1
Stator
2C14030P22 Frame 1
2C14030P23 Beam 1
2C14030P24 Latch 1
2C14030P25 Cable 2
2C14030P26 Adj. Screw 1
2C14030P27 Pivot Plate 1
2C14030P28 Nut 1
2C14030P29 Clevis 2
BLC16R20SL12 Quick Release Clevis 2 A
Pin
BLC4R12SL8 Quick Release Clevis 1 A
Pin
BLC4R85L8 Quick Release Clevis 1 A
Pin
18912 Thrust Washer 1 H
32711 Clevis Pin 2 F
FOR ALL
2C14030G04
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C14030G04
Page 2
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
TRUCK, LOW PRESSURE TURBINE MODULE
2C14031G04
PURPOSE AND USE: For transportation and storage of the low pressure
turbine module in the horizontal position.
DESCRIPTION: Consists of a frame made of welded square section tube provided
with four casters. Attached to the frame are two supports which engage
the ground handling mounts of the module and two supports which engage
the forward flange of the module. Welded on the bottom of the frame
are two channels for use with a lift truck.
DIMENSIONS: 65 x 46 x 35 in. (1650 x 1170 x 890 mm).
WEIGHT: 200 lb (90 kg).
SUPPORTING TOOLS: Fixture, Lift and Turn - Low Pressure Turbine Module (2C14052).
TOOL MAINTENANCE: Apply a light coat of oil to all unpainted surfaces when
stored. Lubricate casters periodically when in use.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS LIST
GROUP PART NO. NOMENCLATURE QUANTITY SUPPLIER
NUMBER CODE
G04 2C14031P04 Left Hand Stand 1
2C14031P06 Right Hand Stand 1
2C14031P22 Base 1
2C14031P28 Caster Pad 4
2C14031P30 Column 1
2C14031P31 Clevis 2
2C14031P32 Column 1
S-WWMS-6P-2-4SL Swivel Caster 4 N
C00-01-001 Floor Lock 2 O
BLS6BC21SL6 Ball-Lok Pin 2 A
BLS9BC21SL6 Ball-Lok Pin 2 A
MS16208-105 Screw 16
12705-8C-32B Shoulder Screw 2 AK
FOR ALL
2C14031G04
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C14031G04
Page 2
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FIXTURE, LIFT - HIGH PRESSURE TURBINE ROTOR, AFT
2C14038G02
PURPOSE AND USE: The Lift Fixture is used to lift the high pressure
turbine rotor assembly from the aft end and turn the assembly from
forward end down to aft end down.
DESCRIPTION: The Lift Fixture consists of a plate with a full swiveling lift eye
and a lift bar. The tool has a black oxide or black phosphate finish.
DIMENSIONS: 27 x 12 in. (686 x 305 mm).
WEIGHT: 18 lb (8 kg).
SUPPORTING TOOLS: Overhead Hoist, 2C14002, 2C14003.
TOOL MAINTENANCE: Apply corrosion preventive oil to all surfaces that
have black oxide or black phosphate coating.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing 2C14038.
FOR ALL
2C14038G02
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C14038G02
Page 2
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
DELETED
2C14040G06
PURPOSE AND USE: This tool has been deleted in its entirety.
Superseded by tool 2C14040G08.
FOR ALL
2C14040G06
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
TORQUE ADAPTER, PRESSURE TUBE - COUPLING NUT, HIGH PRESSURE TURBINE ROTOR
2C14040G07
PURPOSE AND USE: The Pressure Tube Torque Adapter is used to transmit
rotational force from a torque multiplier to remove or install and torque
the high pressure turbine rotor coupling nut.
DESCRIPTION: The Pressure Tube Torque Adapter consists of a tube with male splines
on both ends located inside a larger tube that has anti-rotation devices attached to
it. The tool has a black oxide or black phosphate finish. This tool is aplicable
to all CF6-80C2 engines models except model B8F (which has boltless, R88DT rotors).
DIMENSIONS: 34 x 6 x 6 in. (864 x 152 x 152 mm).
WEIGHT: 90 lbs (41 kg).
SUPPORTING TOOLS: Sweeney Torque Multiplier 8112, 2C6187, 2C14099, 2C14100.
TOOL MAINTENANCE: Apply corrosion preventive oil to all surfaces that
have black oxide or black phosphate coating.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing 2C14040.
PURPOSE AND USE: The Pressure Tube Torque Adapter is used to transmit
rotational force from a torque multiplier to remove or install and torque
the high pressure turbine rotor coupling nut.
DESCRIPTION: The Pressure Tube Torque Adapter consists of a tube with male splines
on both ends located inside a larger tube that has anti-rotation devices attached
to it. The tool has a black oxide or black phosphate finish. This tool has a
horizontal support that is necessary for thicker aft rotor flanges of the boltless,
R88DT rotors. However, it can be used with all CF6-80C2 engine models.
DIMENSIONS: 34 x 6 x 6 in. (864 x 152 x 152 mm).
WEIGHT: 90 lbs (41 kg).
SUPPORTING TOOLS: Sweeney Torque Multiplier 8112, 2C6187, 2C14099, 2C14100.
TOOL MAINTENANCE: Apply corrosion preventive oil to all surfaces that
have black oxide or black phosphate coating.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing 2C14040.
FOR ALL
2C14040G08
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C14040G08
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
STAND, REWORK AND STORAGE - HIGH PRESSURE TURBINE ROTOR
2C14048G03
PURPOSE AND USE: The Rework and Storage Stand is used to disassemble, store and
transport the high pressure turbine rotor in a vertical position.
DESCRIPTION: The Rework and Storage Stand is a square base made of metal tubes
mounted on casters. In the center are four vertical tubes that support a circular
aluminum plate that interfaces with the stage 1 disk. The primary color of the tool
is blue. This tool is applicable to all CF6-80C2 engine models except model B8F.
DIMENSIONS: 40 x 40 x 28 in. (1,016 x 1,016 x 711 mm).
WEIGHT: 400 lbs (181 kg).
SUPPORTING TOOLS: None.
TOOL MAINTENANCE: TBD
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing 2C14048.
PURPOSE AND USE: The Rework and Storage Stand is used to disassemble, store and
transport the high pressure turbine rotor in a vertical position.
DESCRIPTION: The Rework and Storage Stand is a square base made of metal tubes
mounted on casters. In the center are four vertical tubes that support a
circular aluminum plate that interfaces with the stage 1 disk. The primary
color of the tool is blue. This tool is only applicable to CF6-80C2 engine
model B8F, which has boltless, R88DT rotors.
DIMENSIONS: 40 x 40 x 28 in. (1,016 x 1,016 x 711 mm).
WEIGHT: 400 lbs (181 kg).
SUPPORTING TOOLS: None.
TOOL MAINTENANCE: TBD
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing 2C14048.
FOR B8F
2C14048G04
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR B8F
2C14048G04
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
TRUCK - HIGH PRESSURE TURBINE ROTOR HORIZONTAL
2C14049G02
PURPOSE AND USE: The Truck is used to transport and store the high pressure
turbine rotor assembly in a horizontal position.
DESCRIPTION: The Truck is a square base made of metal tubes mounted
on four casters. There are two upright supports for the rotor. The
primary color of the tool is blue.
DIMENSIONS: 46 x 46 x 34 in. (1168 x 1168 x 864 mm).
WEIGHT: 375 lb (170 kg).
SUPPORTING TOOLS: None.
TOOL MAINTENANCE: Apply corrosion preventive oil to all surfaces that
have black oxide or black phosphate coating.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing 2C14049.
FOR ALL
2C14049G02
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C14049G02
Page 2
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
TRUCK - HIGH PRESSURE TURBINE ROTOR HORIZONTAL
2C14049G03
PURPOSE AND USE: The Truck is used to transport and store the high pressure
turbine rotor assembly in a horizontal position.
DESCRIPTION: The Truck is a square base made of metal tubes mounted on four casters.
There are two upright supports for the rotor. The primary color of the tool is
blue. It has a modified roller to improve removal of the HPT Rotor from the truck.
DIMENSIONS: 46 x 46 x 34 in. (1,168 x 1,168 x 864 mm).
WEIGHT: 375 lbs (170 kg).
SUPPORTING TOOLS: None.
TOOL MAINTENANCE: Apply corrosion preventive oil to all surfaces that
have black oxide or black phosphate coating.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing 2C14049.
FOR ALL
2C14049G03
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C14049G03
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FIXTURE, LIFT AND TURN - LOW PRESSURE TURBINE - HORIZONTAL
2C14052G05
PURPOSE AND USE: The Lift and Turn Fixture is used to lift and turn the low pressure
turbine module during installation to or removal from the engine.
DESCRIPTION: The Lift and Turn Fixture is a fabricated steel strongback attached to
an L-shaped lift bar with an adjustable CG. The primary color of the tool is blue.
DIMENSIONS: 38 x 40 x 66 in. (965 x 1016 x 1680 mm).
WEIGHT: 335 lb (152 kg).
SUPPORTING TOOLS: Overhead Hoist (4000 lb (101600 kg) minimum capacity).
TOOL MAINTENANCE: Apply corrosion preventive oil to all surfaces that
have black oxide or black phosphate coating.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing 2C14052.
FOR ALL
2C14052G05
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C14052G05
Page 2
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
PULLER, NO. 4 BEARING - AFT INNER RACE
2C14061G03
PURPOSE AND USE: To provide a means of reaching down through the compressor rear
frame to attach to the puller groove of the No. 4B aft inner race for removing it.
DESCRIPTION: Consists of a tube with expandable feet. A second tube inside the
first moves axially forward to expand the feet which engage the No. 4B aft inner
race puller groove. Removal force is generated by a hydraulic ram assembly.
DIMENSIONS: 13 in. dia x 29 in. (330 mm dia x 737 mm).
WEIGHT: 45 lb (21 kg).
SUPPORTING TOOLS: Hydraulic Hand Pump.
TOOL MAINTENANCE: Coat treated surfaces (black oxide or black phosphate)
with corrosion preventive light oil when stored.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS LIST
GROUP PART NO. NOMENCLATURE QUANTITY SUPPLIER
NUMBER CODE
G03 2C14061P03 Locking Plate 1
2C14061P09 Puller 1
2C14061P11 Pilot 1
2C14061P12 Limit Tube 4
RC-57 Hydraulic Cylinder 1 D
FOR ALL
2C14061G03
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C14061G03
Page 2
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
ADAPTER, PUSHER/COUNTERTORQUE - COMPRESSOR REAR FRAME AFT SUMP HOUSING
2C14073G03
PURPOSE AND USE: To provide a rapid attachment for the damper support
pusher and No. 5R bearing housing pushers and provide for the attachment
of a torque multiplier fixture.
DESCRIPTION: Consists of a ring shaped adapter which is bolted to the
aft sump housing. Tapped holes are provided for mounting the pushers
and torque multiplier fixture.
DIMENSIONS: 15 in. dia x 4 in. (380 mm dia x 100 mm).
WEIGHT: 25 lb (11 kg).
SUPPORTING TOOLS: Support, 2C14621G01; Puller, 2C14618G01; Pusher 2C14190G02.
TOOL MAINTENANCE: Coat treated surfaces (black oxide or black phosphate)
with corrosion preventive light oil when stored.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS LIST
GROUP PART NO. NOMENCLATURE QUANTITY SUPPLIER
NUMBER CODE
G03 2C14073P09 Adapter Ring 1
(Inseparable Assembly)
FOR ALL
2C14073G03
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C14073G03
Page 2
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FIXTURE, RAISE/LOWER - ACCESSORY DRIVE GEARBOX MODULE
2C14084G01
PURPOSE AND USE: To provide a means of raising and lowering the accessory
drive module with an engine in the horizontal position.
DESCRIPTION: Consists of a scissors type hydraulic lift table raised by
a manual hydraulic pump. The lift table incorporates casters, floor
locks, and four leveling jackscrews. The top of the lift table has
provisions for attaching the 2C14086 lift fixture.
DIMENSIONS: 40 x 56 x 12 in. (1016 x 1422 x 305 mm).
WEIGHT: 500 lb (227 kg).
SUPPORTING TOOLS: Fixture, 2C14086G01.
TOOL MAINTENANCE: Apply a light coat of corrosion preventive oil to
all unpainted surfaces when stored.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS LIST
GROUP PART NO. NOMENCLATURE QUANTITY SUPPLIER
NUMBER CODE
G01 2C14084P02 Post 4
2C14084P03 Plate 4
CL-6-8LP-R-2.7 Ball-Lock Pin 4 I
CL-21-DA-10.0 Cable Assembly 4 I
Special M-107-36.0 Scissor Lift EQ
x 55.0 Platform 7.0
Closed Height
FOR ALL
2C14084G01
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C14084G01
Page 2
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
WRENCH, STARTER - LOW PRESSURE TURBINE COUPLING NUT
2C14092G03
PURPOSE AND USE: The Starter Wrench is used to install and remove the low
pressure turbine (LPT) coupling nut from the LPT shaft.
DESCRIPTION: The Starter Wrench is a long aluminum rod with a handle on one end and
a circular housing on the other. Two circular plates are located along the rod. A
coupling nut wrench is threaded on the rod, inside the circular housing.
DIMENSIONS: 5.25 x 41 in. (133 x 1041 mm).
WEIGHT: 15 lb (7 kg).
SUPPORTING TOOLS: 2C14016.
TOOL MAINTENANCE: Apply corrosion preventive oil to all surfaces that
have black oxide or black phosphate coating.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing 2C14092.
FOR ALL
2C14092G03
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C14092G03
Page 2
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
WRENCH, COUPLING NUT - LOW PRESSURE TURBINE MIDSHAFT
2C14093G03
PURPOSE AND USE: The Coupling Nut Wrench is used to remove and install the coupling
nut for the low pressure turbine rotor (LPTR) shaft to fan midshaft.
DESCRIPTION: The Coupling Nut Wrench consists of three concentric tubes
with splines on the ends and an adapter wrench. The tool has a black
oxide or black phosphate finish.
DIMENSIONS: 8 x 18 x 51 in. (203 x 457 x 1295 mm).
WEIGHT: 80 lb (36 kg).
SUPPORTING TOOLS: Torque Multipliers (Sweeney 8100 or 8108) or
(Advanced Hydraulics AHX), 2C14602.
TOOL MAINTENANCE: Apply corrosion preventive oil to all surfaces that
have black oxide or black phosphate coating.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing 2C14093.
FOR ALL
2C14093G03
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C14093G03
Page 2
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
WRENCH, COUPLING NUT - LOW PRESSURE TURBINE MIDSHAFT
2C14093G05
PURPOSE AND USE: The Coupling Nut Wrench is used to remove and install the coupling
nut for the low pressure turbine rotor (LPTR) shaft to fan midshaft.
DESCRIPTION: The Coupling Nut Wrench consists of three concentric tubes
with splines on the ends and an adapter wrench. The tool has a black oxide
or black phosphate finish. The G05 version is an alternative to the G03
because of the increased weight capacity.
DIMENSIONS: 8 x 18 x 51 in. (203 x 457 x 1,295 mm).
WEIGHT: 80 lbs (36 kg).
SUPPORTING TOOLS: Torque Multipliers (Sweeney 8100 or 8108) or
(Advanced Hydraulics AHX), 2C14602.
TOOL MAINTENANCE: Apply corrosion preventive oil to all surfaces that
have black oxide or black phosphate coating.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing 2C14093.
FOR ALL
2C14093G05
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C14093G05
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FIXTURE, SEAT CHECK - NO. 4B BEARING AND SEAL
2C14094G06
PURPOSE AND USE: The Seat Check Fixture is used to inspect the seating
of the No. 4B rotating air/oil seal and the No. 4B bearing inner races
onto the compressor rotor spool shaft.
DESCRIPTION: The Seat Check Fixture consists of a circular body with a bracket to
hold a micrometer. A rod extends from the micrometer to measure the distance to the
No. 4B inner race. The tool has a black oxide or black phosphate finish.
DIMENSIONS: 10 x 7 x 6 in. (254 x 178 x 152 mm).
WEIGHT: 7 lb (3 kg).
SUPPORTING TOOLS: None.
TOOL MAINTENANCE: Apply corrosion preventive oil to all surfaces that
have black oxide or black phosphate coating. Periodically check and
calibrate. Refer to drawing 2C14094.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing 2C14094.
FOR ALL
2C14094G06
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C14094G06
Page 2
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FIXTURE, SEATING CHECK - LOW PRESSURE TURBINE ROTOR
2C14096G02
PURPOSE AND USE: The Seating Check Fixture is used to make sure the low pressure
turbine coupling nut is properly seated during engine assembly.
DESCRIPTION: The Seating Check Fixture is an aluminum tube with a spring
loaded plunger through the center. Two circular pilots are welded to the
tube, and a dial indicator is attached to measure plunger travel. The tool
has a black oxide or black phosphate finish.
DIMENSIONS: 6 x 38 in. (152 x 965 mm).
WEIGHT: 20 lb (9 kg).
SUPPORTING TOOLS: None.
TOOL MAINTENANCE: Apply corrosion preventive oil to all surfaces that
have black oxide or black phosphate coating.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing 2C14096.
FOR ALL
2C14096G02
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C14096G02
Page 2
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
CASE, DUMMY - COMPRESSOR STATOR
2C14103G02
PURPOSE AND USE: The Dummy Case is used to support the compressor rear frame
when installing or removing the compressor stator case.
DESCRIPTION: The Dummy Case consists of a segmented circular base with two support
posts that hold a top plate. The tool has a black oxide or black phosphate finish.
DIMENSIONS: 45 x 28 x 6 in. (1143x 711 x 152 mm).
WEIGHT: 20 lb (9 kg).
SUPPORTING TOOLS: Dummy Fan Frame (To be supplied), 2C6054.
TOOL MAINTENANCE: Apply corrosion preventive oil to all surfaces that
have black oxide or black phosphate coating.
QUANTITY PER OPERATION: One (Contains two dummy stator cases).
REPLACEMENT PARTS: Refer to drawing 2C14103.
FOR ALL
2C14103G02
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C14103G02
Page 2
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FIXTURE, HOLDING - NO. 4B BEARING AFT INNER RACE
2C14104G01
PURPOSE AND USE: To position the No. 4B bearing aft inner race on the
high pressure compressor aft shaft.
DESCRIPTION: Consists of a U-shaped tong with a screw-type device near the aft
end which varies the distance between the tong forward ends. Each tong forward
end has a lip that fits into a groove in the aft inner race.
DIMENSIONS: 18 x 8 x 1 in. (457 x 203 x 25 mm).
WEIGHT: 4 lb (2 kg).
SUPPORTING TOOLS: None.
TOOL MAINTENANCE: Coat treated surfaces (black oxide or black phosphate)
with corrosion preventive light oil when stored.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS LIST
GROUP PART NO. NOMENCLATURE QUANTITY SUPPLIER
NUMBER CODE
G01 2C14104P02 Tongs 1
2C14104P03 Pin 2
2C14104P04 Adjusting Nut 1
2C14104P05 R.H. Stud 1
2C14104P06 L.H. Stud 1
FOR ALL
2C14104G01
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C14104G01
Page 2
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
PILOT - LP MIDSHAFT, AFT
2C14105G01
FOR ALL
2C14105G01
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C14105G01
Page 2
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FIXTURE, REMOVE/INSTALL - ACCESSORY GEARBOX DRIVE SHAFT
2C14107G01
FOR ALL
2C14107G01
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C14107G01
Page 2
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FIXTURE, INSTALLATION AND REMOVAL - COMPRESSOR ROTOR FORWARD SHAFT SPLINE ADAPTER
2C14113G01
PURPOSE AND USE: To remove and install the splined adapter in the stage 2
compressor disk during engine assembly/disassembly.
DESCRIPTION: The fixture consists of a base, a pusher for installation,
and a press plate for removal.
DIMENSIONS: 12.5 in. (318 mm) dia x 4.5 in. (114 mm).
WEIGHT: 30 lb (14 kg).
SUPPORTING TOOLS: Arbor press.
TOOL MAINTENANCE: Coat treated surfaces (black oxide or black phosphate)
with corrosion preventive light oil when stored.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS LIST
GROUP PART NO. NOMENCLATURE QUANTITY SUPPLIER
NUMBER CODE
G01 2C14113P02 Base 1
2C14113P03 Press Plate 1
2C14113P04 Protector Tube 1
2C14113P05 Pusher 1
FOR ALL
2C14113G01
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C14113G01
Page 2
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FIXTURE, SEAL/PRESSURIZE - ACCESSORY GEARBOX
2C14124G02
PURPOSE AND USE: To pressurize the accessory gearbox to check carbon seals
for leakage with the engine installed on wing.
WEIGHT: 15 lb (7 kg).
SUPPORTING TOOLS: None.
FOR ALL
2C14124G02
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
GROUP PART NO. NOMENCLATURE QUANTITY SUPPLIER
NUMBER CODE
23203-012 Male Coupler 1 CC
23903-210 Male Connector 2 CC
FOR ALL
2C14124G02
Page 2
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C14124G02
Page 3
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FIXTURE, LIFT - ENGINE, HORIZONTAL
2C14130G04
PURPOSE AND USE: The Lift Fixture is used to lift a complete engine in a
horizontal position using only one hoist.
DESCRIPTION: The Lift Fixture consists of a main lift beam with a cross
beam on the aft end. The primary color of the tool is blue. This tool
is applicable to CF6-80C2 Boeing engines only.
DIMENSIONS: 30 x 120 x 20 in. (762 x 3,048 x 508 mm).
WEIGHT: 300 lbs (136 kg).
SUPPORTING TOOLS: Facility Crane, 12,000 lbs (5,448 kg) minimum capacity.
TOOL MAINTENANCE: Apply corrosion preventive oil to all surfaces that have black
oxide or black phosphate coating and all unplated or unpainted surfaces.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing 2C14130.
PURPOSE AND USE: The Lift Fixture is used to lift a complete engine in a
horizontal position using only one hoist.
DESCRIPTION: The Lift Fixture consists of a main lift beam with a cross
beam on the aft end. The primary color of the tool is blue. This tool
is applicable to CF6-80C2 Airbus engines only.
DIMENSIONS: 30 x 120 x 20 in. (762 x 3,048 x 508 mm).
WEIGHT: 300 lbs (136 kg).
SUPPORTING TOOLS: Facility Crane, 12,000 lbs (5,448 kg) minimum capacity.
TOOL MAINTENANCE: Apply corrosion preventive oil to all surfaces that have black
oxide or black phosphate coating and all unplated or unpainted surfaces.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing 2C14130.
PURPOSE AND USE: The Lift Fixture is used to lift a complete engine in a
horizontal position using only one hoist.
DESCRIPTION: The Lift Fixture consists of a main lift beam with a cross
beam on the aft end. The primary color of the tool is blue. This tool
is applicable to CF6-80C2 Douglas engines only.
DIMENSIONS: 30 x 120 x 20 in. (762 x 3,048 x 508 mm).
WEIGHT: 300 lbs (136 kg).
SUPPORTING TOOLS: Facility Crane, 12,000 lbs (5,448 kg) minimum capacity.
TOOL MAINTENANCE: Apply corrosion preventive oil to all surfaces that have black
oxide or black phosphate coating and all unplated or unpainted surfaces.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing 2C14130.
PURPOSE AND USE: The Lift Fixture is used to lift a complete engine in a
horizontal position using only one hoist.
DESCRIPTION: The Lift Fixture consists of a main lift beam with a cross
beam on the aft end. The primary color of the tool is blue. This tool
is applicable to CF6-80C2 Boeing engines only.
DIMENSIONS: 30 x 120 x 20 in. (762 x 3,048 x 508 mm).
WEIGHT: 300 lbs (136 kg).
SUPPORTING TOOLS: Facility Crane, 12,000 lbs (5,448 kg) minimum capacity.
TOOL MAINTENANCE: Apply corrosion preventive oil to all surfaces that have black
oxide or black phosphate coating and all unplated or unpainted surfaces.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing 2C14130.
PURPOSE AND USE: The Lift Fixture is used to lift a complete engine in a
horizontal position using only one hoist.
DESCRIPTION: The Lift Fixture consists of a main lift beam with a cross
beam on the aft end. The primary color of the tool is blue. This tool
is applicable to CF6-80C2 Airbus engines only.
DIMENSIONS: 30 x 120 x 20 in. (762 x 3,048 x 508 mm).
WEIGHT: 300 lbs (136 kg).
SUPPORTING TOOLS: Facility Crane, 12,000 lbs (5,448 kg) minimum capacity.
TOOL MAINTENANCE: Apply corrosion preventive oil to all surfaces that have black
oxide or black phosphate coating and all unplated or unpainted surfaces.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing 2C14130.
PURPOSE AND USE: The Lift Fixture is used to lift a complete engine in a
horizontal position using only one hoist.
DESCRIPTION: The Lift Fixture consists of a main lift beam with a cross
beam on the aft end. The primary color of the tool is blue. This tool
is applicable to CF6-80C2 Douglas engines only.
DIMENSIONS: 30 x 120 x 20 in. (762 x 3,048 x 508 mm).
WEIGHT: 300 lbs (136 kg).
SUPPORTING TOOLS: Facility Crane, 12,000 lbs (5,448 kg) minimum capacity.
TOOL MAINTENANCE: Apply corrosion preventive oil to all surfaces that have black
oxide or black phosphate coating and all unplated or unpainted surfaces.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing 2C14130.
PURPOSE AND USE: To assure that the high pressure turbine rotor
is fully seated on the shaft.
DESCRIPTION: Consists of a depth micrometer with a 15 inch spindle
bolted to a positioning bar.
DIMENSIONS: 15 x 15 x 4 in. (380 x 380 x 100 mm).
WEIGHT: 8 lb (4 kg).
SUPPORTING TOOLS: None required.
TOOL MAINTENANCE: Coat treated surfaces (black oxide or black phosphate)
with corrosion preventive light oil when stored.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS LIST
GROUP PART NO. NOMENCLATURE QUANTITY SUPPLIER
NUMBER CODE
G02 2C14131P07 Rod 1
2C14131P08 Plate 1
2C14131P09 Depth Micrometer 1
FOR ALL
2C14131G02
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C14131G02
Page 2
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FIXTURE, LIFT - LPT ROTOR AND LPT MODULE - VERTICAL
2C14132G02
PURPOSE AND USE: The Lift Fixture is used to lift the low pressure turbine
rotor/module vertically with fixture 2C14602 installed.
DESCRIPTION: The Lift Fixture consists of an internally threaded cap with an eye
bolt attached to the center. The tool has a black oxide or black phosphate finish.
DIMENSIONS: 7.5 x 2 in. (191 x 51 mm).
WEIGHT: 10 lbs (5 kg).
SUPPORTING TOOLS: Overhead Hoist, 2C14016.
TOOL MAINTENANCE: Apply corrosion preventive oil to all surfaces that
have black oxide or black phosphate coating.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing 2C14132.
FOR ALL
2C14132G02
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C14132G02
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
GUIDE - LP TURBINE REAR FRAME
2C14133G03
PURPOSE AND USE: To prevent damaging the No. 6 bearing rotating oil seal
while installing/removing the turbine rear frame.
DESCRIPTION: Consists of a tube with one tapered end and internal
threads on the other end. A small tube is tack-welded near the tapered
end that serves as a handle.
DIMENSIONS: 7 in. dia x 6 in. (180 mm dia x 152 mm).
WEIGHT: 8 lb (4 kg).
SUPPORTING TOOLS: Stand, 2C14208G01.
TOOL MAINTENANCE: Coat treated surfaces (black oxide or black phosphate)
with corrosion preventive light oil when stored.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS LIST
GROUP PART NO. NOMENCLATURE QUANTITY SUPPLIER
NUMBER CODE
G03 2C14133P05 Tube 1
2C14133P06 Guide 1
FOR ALL
2C14133G03
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C14133G03
Page 2
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
TOOL, INSTALLATION - ACCESSORY GEARBOX MATING RING SEAL
2C14137G01
PURPOSE AND USE: The Installation Tool is used to install the seal
mating rings into the accessory gearbox.
DESCRIPTION: The Installation Tool is a pair of pliers with three fingers which fit
over the outside diameter of the seal mating rings. The tool has a black oxide or
black phosphate finish. This tool is applicable to CF6-80C2 B6FA engines only.
DIMENSIONS: 3 x 5 x 9.5 in. (76 x 127 x 241 mm).
WEIGHT: 15 lbs (7 kg).
SUPPORTING TOOLS: 2C14138.
TOOL MAINTENANCE: Apply corrosion preventive oil to all surfaces that
have black oxide or black phosphate coating.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing 2C14137.
PURPOSE AND USE: The Installation Tool is used to install the seal
mating rings into the accessory gearbox.
DESCRIPTION: The Installation Tool is a pair of pliers with three fingers which fit
over the outside diameter of the seal mating rings. The tool has a black oxide or
black phosphate finish. This tool is applicable to CF6-80C2 B6FA engines only.
DIMENSIONS: 3 x 5 x 9.5 in. (76 x 127 x 241 mm).
WEIGHT: 15 lbs (7 kg).
SUPPORTING TOOLS: 2C14138.
TOOL MAINTENANCE: Apply corrosion preventive oil to all surfaces that
have black oxide or black phosphate coating.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing 2C14137.
FOR B6FA
2C14137G02
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR B6FA
2C14137G02
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
DELETED
2C14137G03
PURPOSE AND USE: This tool has been deleted in its entirety.
FOR ALL
2C14137G03
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
TOOL, INSTALLATION - ACCESSORY GEARBOX MATING RING SEAL
2C14137G04
PURPOSE AND USE: The Installation Tool is used to install the seal
mating rings into the accessory gearbox.
DESCRIPTION: The Installation Tool is a pair of pliers with three fingers which fit
over the outside diameter of the seal mating rings. The tool has a black oxide or
black phosphate finish. This tool is applicable to CF6-80C2 B6FA engines only.
DIMENSIONS: 3 x 5 x 9.5 in. (76 x 127 x 241 mm).
WEIGHT: 15 lbs (7 kg).
SUPPORTING TOOLS: 2C14138.
TOOL MAINTENANCE: Apply corrosion preventive oil to all surfaces that
have black oxide or black phosphate coating.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing 2C14137.
FOR B6FA
2C14137G04
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR B6FA
2C14137G04
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FIXTURE, REMOVAL - MATING SEAL RINGS - ACCESSORY GEARBOX
2C14138G01
PURPOSE AND USE: The Removal Fixture is used to remove mating seal
rings from the accessory gearbox.
DESCRIPTION: The Removal Fixture is a pusher plate, an inner sleeve with
thirty fingers, a neoprene stop ring and an outer sleeve. This tool is
applicable to CF6-80C2 B6FA engines only.
DIMENSIONS: Container, 4 x 4 x 12 in. (102 x 102 x 305 mm).
WEIGHT: 12 lbs (5 kg).
SUPPORTING TOOLS: 2C14137.
TOOL MAINTENANCE: Apply corrosion preventive oil to all surfaces that
have black oxide or black phosphate coating.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS LIST
GROUP PART NO. NOMENCLATURE QUANTITY SUPPLIER
NUMBER CODE
G01 2C14138P02 Sleeve, Inner 1
2C14138P04 Sleeve, Outer 1
2C14138P06 Plate, Pusher 1
2C14138P08 Ring, Stop 1
2C14138P10 Screw 1
2C14138P11 Container 1
Commercial Nut Self-Locking - STL 1
FOR B6FA
2C14138G01
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR B6FA
2C14138G01
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FIXTURE, REMOVAL - MATING SEAL RINGS - ACCESSORY GEARBOX
2C14138G02
PURPOSE AND USE: The Removal Fixture is used to remove mating seal
rings from the accessory gearbox.
DESCRIPTION: The Removal Fixture is a pusher plate, an inner sleeve with
thirty fingers, a neoprene stop ring and an outer sleeve. This tool is
applicable to CF6-80C2 B6FA engines only.
DIMENSIONS: Container, 4 x 4 x 12 in. (102 x 102 x 305 mm).
WEIGHT: 12 lbs (5 kg).
SUPPORTING TOOLS: 2C14137.
TOOL MAINTENANCE: Apply corrosion preventive oil to all surfaces that
have black oxide or black phosphate coating.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS LIST
GROUP PART NO. NOMENCLATURE QUANTITY SUPPLIER
NUMBER CODE
G02 2C14138P03 Sleeve, Inner 1
2C14138P05 Sleeve, Outer 1
2C14138P07 Plate, Pusher 1
2C14138P09 Ring, Stop 1
2C14138P10 Screw 1
2C14138P11 Container 1
Commercial Nut Self-Locking - STL 1
FOR B6FA
2C14138G02
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR B6FA
2C14138G02
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
DELETED
2C14138G03
PURPOSE AND USE: This tool has been deleted in its entirety.
FOR ALL
2C14138G03
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FIXTURE, REMOVAL - MATING SEAL RINGS - ACCESSORY GEARBOX
2C14138G04
PURPOSE AND USE: The Removal Fixture is used to remove mating seal
rings from the accessory gearbox.
DESCRIPTION: The Removal Fixture is a pusher plate, an inner sleeve with
thirty fingers, a neoprene stop ring and an outer sleeve. This tool is
applicable to CF6-80C2 B6FA engines only.
DIMENSIONS: Container, 4 x 4 x 12 in. (102 x 102 x 305 mm).
WEIGHT: 12 lbs (5 kg).
SUPPORTING TOOLS: 2C14137.
TOOL MAINTENANCE: Apply corrosion preventive oil to all surfaces that
have black oxide or black phosphate coating.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS LIST
GROUP PART NO. NOMENCLATURE QUANTITY SUPPLIER
NUMBER CODE
G04 2C14138P10 Screw 1
2C14138P11 Container 1
2C14138P15 Plate, Pusher 1
2C14138P17 Sleeve, Inner 1
2C14138P18 Sleeve, Outer 1
2C14138P19 Ring, Stop 1
Commercial Nut Self-Locking - STL 1
FOR B6FA
2C14138G04
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR B6FA
2C14138G04
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
CONTAINER, SHIPPING-HIGH PRESSURE TURBINE ROTOR AND STG 2 NOZZLE
2C14148G01
PURPOSE AND USE: To ship or store a high pressure turbine and stage 2 nozzle.
DESCRIPTION: Consists of a steel base with fork lift provisions, a plywood
box cover and brackets to hold and protect the high pressure rotor/stage
2 nozzle for shipping or storage.
DIMENSIONS: 48 x 65 x 65 in. (1219 x 1651 x 1651 mm).
WEIGHT: To be supplied.
SUPPORTING TOOLS: None.
TOOL MAINTENANCE: Coat treated surfaces (black oxide or black phosphate)
with corrosion preventive light oil when stored.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS LIST
GROUP PART NO. NOMENCLATURE QUANTITY SUPPLIER
NUMBER CODE
G01 2C14148P02 Frame 1
2C14148P03 Cover 1
2C14148P04 Bracket 4
2C14148P05 Lift Eye 3
29810-5 Shipping Mount 4 CK
TL-4 Leveling Pad 4 C
FOR ALL
2C14148G01
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C14148G01
Page 2
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
CONTAINER, SHIPPING - LP TURBINE MODULE
2C14149G02
PURPOSE AND USE: To ship or store the low pressure turbine module.
DESCRIPTION: Made primarily of wood with a metal frame support structure mounted
on a steel base. The base supports a shock mount system and a mounting structure
on which the LPT module seats and is secured. The module is centered by a
post with a protective sleeve and supported by a clamping device. The forward
flange of the LPT is seated on a protective textolite ring and bolted to a
baseplate which is part of the suspended steel structure.
DIMENSIONS: 70 x 70 x 56 in. (1780 x 1780 x 1420 mm).
WEIGHT: 1800 lb (816 kg).
SUPPORTING TOOLS: Fixture, 2C14762G01; Fixture, 2C14052G03; Overhead Hoist.
TOOL MAINTENANCE: Coat treated surfaces (black oxide or black phosphate)
with corrosion preventive light oil when stored.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS LIST
GROUP PART NO. NOMENCLATURE QUANTITY SUPPLIER
NUMBER CODE
G02 2C14149P02 Container 1
2C14149P03 Pallet 1
2C14149P04 Frame 1
2C14149P05 Stand 1
2C14149P07 Bracket 6
2C14149P23 Bolt Ring 3
2C14149P26 Plate 1
2C14149P27 Washer 1
2C14149P28 Cap 1
2C14149P36 Plastic Sleeve 1
CBG-1500-20C2 Shock and Vibration 4 CJ
Mount
FS-7 Eye Bolt 6 C
0.3125 Size Washer, Nylon 101 20 BM
FOR ALL
2C14149G02
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C14149G02
Page 2
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
DELETED
2C14155G01
PURPOSE AND USE: This tool has been deleted in its entirety.
FOR ALL
2C14155G01
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
CLOSURES, PROTECTIVE - ENGINE PORTS
2C14155G05
PURPOSE AND USE: The Protective Closures are used to close off various accessory
pads and service air ports to prevent entrance of foreign objects and/or loss
of bleed air and lubrication fluids during engine test.
DESCRIPTION: The Protective Closure set consists of several couplings and seal
rings. A container is provided. This is for shipping/storage.
DIMENSIONS: Container, 24 x 12 x 6 in. (610 x 305 x 152 mm).
WEIGHT: 20 lbs (9.1 kg).
SUPPORTING TOOLS: None.
TOOL MAINTENANCE: Apply corrosion preventive oil to all surfaces that
have black oxide or black phosphate coating.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing 2C14155.
FOR ALL
2C14155G05
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C14155G05
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
CLOSURES, PROTECTIVE - ENGINE PORTS
2C14155G06
PURPOSE AND USE: The Protective Closures are used to close off various accessory
pads and service air ports to prevent entrance of foreign objects and/or loss
of bleed air and lubrication fluids during engine test.
DESCRIPTION: The Protective Closure set consists of several couplings and seal
rings. A container is provided. This is for testing.
DIMENSIONS: Container, 24 x 12 x 6 in. (610 x 305 x 152 mm).
WEIGHT: 25 lbs (11.3 kg).
SUPPORTING TOOLS: None.
TOOL MAINTENANCE: Apply corrosion preventive oil to all surfaces that
have black oxide or black phosphate coating.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing 2C14155.
FOR ALL
2C14155G06
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C14155G06
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FIXTURE, GRINDING - COMPRESSOR STATOR VANE TIPS
2C14156G02
PURPOSE AND USE: To position the compressor stator case on the rotating
base of the vertical turret lathe, restrain the forward and aft stator case
flanges round and flat, and fix the position of stages 3, 4, and 5 variable
stator vanes for grinding of stator vane tips.
DESCRIPTION: Consists of two rabbeted steel rings which fit the forward and
aft flanges of the stator case assembly. A two inch diameter post is attached
between the two rings which supports the rod ends and turnbuckles to properly
position stages 3, 4, and 5 variable stator vanes.
DIMENSIONS: 50 x 50 x 15 in. (1270 x 1270 x 381 mm).
WEIGHT: 1000 lb (454 kg).
SUPPORTING TOOLS: Protractor, 2C6459G09; Sling, MSE-53; Overhead Hoist.
TOOL MAINTENANCE: Coat treated surfaces (black oxide or black phosphate)
with corrosion preventive light oil when stored.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS LIST
GROUP PART NO. NOMENCLATURE QUANTITY SUPPLIER
NUMBER CODE
G02 2C14156P02 Ring 1
2C14156P03 Support 1
2C14156P04 Pad 1
2C14156P06 Clevis 3
2C14156P07 Turnbuckle 3
2C14156P23 Ring Plate 1
2C14156P24 Pin Screw 2
2C14156P25 Pin Screw 1
2C14156P26 Pin Screw 1
CL-2-DP Diamond Locating Pin 1 I
CL-4-SHA Clamp Assembly 8 I
ADB-23053 Safety Hoist Ring 6 CN
HML-4C Rod End 3 CO
HM-4C Rod End 3 CO
CL-3-RP Round Pin 3 I
FOR ALL
2C14156G02
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C14156G02
Page 2
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
WRENCH SET - LP TURBINE ROTOR
2C14165G01
PURPOSE AND USE: To remove/install the nuts that retain the LP turbine
rotor stages 2, 3 and 4 together.
DESCRIPTION: Consists of two U-shaped rods, each with a 0.5 in. (12.7 mm)
square female drive on one end and a 0.375 in. (9.5 mm) square male drive
on the other end. On the male end of the tools, a two inch offset adapter
is installed and secured with a pin. One uses a 0.375 in. (9.5 mm) hex
while the other has a 0.438 in. (11.1 mm) hex.
DIMENSIONS: 3 x 7 x 6 in. (76 x 178 x 152 mm).
WEIGHT: 7 lb (3 kg).
SUPPORTING TOOLS: None.
TOOL MAINTENANCE: Coat treated surfaces (black oxide or black phosphate)
with corrosion preventive light oil when stored.
QUANTITY PER OPERATION: One set.
REPLACEMENT PARTS LIST
GROUP PART NO. NOMENCLATURE QUANTITY SUPPLIER
NUMBER CODE
G01 2C14165P02 Wrench 1
2C14165P03 Torque Adapter 1
2C14165P04 Torque Adapter 1
2C14165P05 Container 3
FOR ALL
2C14165G01
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C14165G01
Page 2
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
TOOL SET, INSTALLATION AND REMOVAL - NO. 5R BEARING
2C14176G05
PURPOSE AND USE: The Installation and Removal Tool Set is used to remove and
install the No. 5R bearing and the No. 5R bearing spanner nut.
DESCRIPTION: The Installation and Removal Tool Set consists of a wrench,
holder, anti-torque plate, pusher, and puller.
DIMENSIONS: 14 x 14 x 18 in. (356 x 356 x 457 mm).
WEIGHT: 130 lb (59 kg).
SUPPORTING TOOLS: Sweeney Torque Multiplier, Model 8100 or equivalent.
TOOL MAINTENANCE: Apply corrosion preventive oil to all surfaces that
have black oxide or black phosphate coating.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing 2C14176.
FOR ALL
2C14176G05
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C14176G05
Page 2
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
ADAPTER, PEDESTAL - COMPRESSOR REAR FRAME AFT FLANGE
2C14178G01
PURPOSE AND USE: To support the engine at the compressor rear frame
aft flange during maintenance or storage.
DESCRIPTION: Consists of two identical flat plates radiused on one side.
Three lugs with one hole in each lug protrude from the radiused side and
bolt to the engine. At the bottom of each plate there is an elongated
hole that interfaces with the pedestal supports.
DIMENSIONS: 7 x 13 x 0.60 in. (180 x 330 x 15 mm).
WEIGHT: 13 lb (6 kg).
SUPPORTING TOOLS: Support, 2C6339G03 or G05.
TOOL MAINTENANCE: Coat treated surfaces (black oxide or black phosphate) with
corrosion preventive light oil when stored. Load test periodically (see GE
drawing 2C14178 for load test diagram and applicable NOTE).
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS LIST
GROUP PART NO. NOMENCLATURE QUANTITY SUPPLIER
NUMBER CODE
G01 2C14178P02 Bracket 2
FOR ALL
2C14178G01
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C14178G01
Page 2
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
PULLER, BUMPER BEARING
2C14179G01
PURPOSE AND USE: To remove bumper bearing from compressor rotor air duct.
DESCRIPTION: Consists of a base, nut, plate, rod and a hydraulic cylinder. The
base attaches to the compressor rotor air duct. The cylinder is actuated and
pulls the plate which pulls the bumper bearing from the air duct.
DIMENSIONS: 8 in. dia x 13 in. (203 mm dia x 330 mm).
WEIGHT: TBD
SUPPORTING TOOLS: Hydraulic Hand Pump.
TOOL MAINTENANCE: Treated surfaces (black oxide or black phosphate) with
corrosion preventive light oil when stored.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS LIST
GROUP PART NO. NOMENCLATURE QUANTITY SUPPLIER
NUMBER CODE
G01 2C14179P02 Base 1
2C14179P03 Nut 1
2C14179P04 Plate 1
2C14179P05 Threaded Rod 1
RCH-121 Hollow Plunger 1 D
Cylinder
AR-400 Coupler 1 D
Z-410 Dust Cap 1 D
FOR ALL
2C14179G01
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C14179G01
Page 2
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FIXTURE, GRIND - HIGH PRESSURE TURBINE SHROUD
2C14181G03
PURPOSE AND USE: The Grind Fixture is used to restrain the high pressure
turbine (HPT) stator assembly during inspection and grinding of the
stage 1 and 2 turbine shrouds.
DESCRIPTION: The Grind Fixture consists of a round base with posts that
support two restraining rings. A lift bar attached to one of the rings.
The primary color of the tool is blue.
DIMENSIONS: 48 x 12.5 in. (1219 x 318 mm).
WEIGHT: 600 lb (272 kg).
SUPPORTING TOOLS: Standard Vertical Turret Lathe.
TOOL MAINTENANCE: Apply corrosion preventive oil to all surfaces that
have black oxide or black phosphate coating. Periodically check and
recalibrate. Refer to drawing 2C14181.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing 2C14181.
FOR ALL
2C14181G03
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C14181G03
Page 2
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FIXTURE, GRIND - HIGH PRESSURE TURBINE SHROUD
2C14181G04
PURPOSE AND USE: The Grind Fixture is used to restrain the high pressure
turbine (HPT) stator assembly during inspection and grinding of the
stage 1 and 2 turbine shrouds.
DESCRIPTION: The Grind Fixture consists of a round base with posts that
support two restraining rings. A lift bar attached to one of the rings.
The primary color of the tool is blue.
DIMENSIONS: 48 x 12.5 in. (1219 x 318 mm).
WEIGHT: 600 lb (272 kg).
SUPPORTING TOOLS: Standard Vertical Turret Lathe.
TOOL MAINTENANCE: Apply corrosion preventive oil to all surfaces that
have black oxide or black phosphate coating. Periodically check and
recalibrate. Refer to drawing 2C14181.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing 2C14181.
FOR ALL
2C14181G04
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C14181G04
Page 2
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FIXTURE, LIFT/TURN CORE MODULE - FORWARD
2C14186G02
PURPOSE AND USE: To lift and turn the core module from horizontal to vertical.
DESCRIPTION: Consists of an inverted "U" rectangular tube to which is attached a
lift eye, swivels for interfacing with the compressor case horizontal flanges and
a pivoting arm which interfaces with the compressor case rear flange.
DIMENSIONS: 45 x 38 x 7 in. (1143 x 965 x 178 mm).
WEIGHT: 110 LB (50 kg).
SUPPORTING TOOLS: Overhead Hoists (2); Fixture 2C14030G03.
TOOL MAINTENANCE: Coat treated surfaces (black oxide or black phosphate) with
corrosion preventive light oil when stored. Load test periodically (see GE
drawing 2C14186 for load test diagram and applicable NOTE).
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS LIST
GROUP PART NO. NOMENCLATURE QUANTITY SUPPLIER
NUMBER CODE
G02 2C14186P03 Left Hand Foot 1
2C14186P04 Right Hand Foot 1
2C14186P05 Rod 2
2C14186P06 Bracket 1
2C14186P07 Tie Rod 1
2C14186P08 Washer 4
2C14186P09 Washer 4
2C14186P17 Frame 1
2C14186P18 Adjustable Screw 1
2C14186P19 Pivot Plate 1
2C14186P20 Hex Nut 1
BLC8R20SL12 Ball-Lok Pin 5 A
MS21045-C7 Hex Nut 2
14S21045-C8 Hex Nut 2
18912 Thrust Washer 1 H
18882 Thrust Washer 1 H
FOR ALL
2C14186G02
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C14186G02
Page 2
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
PUSHER, SUMP CLOSURE, FORWARD BEARING NO. 5R
2C14190G03
PURPOSE AND USE: The Pusher is used to install the No. 5R forward sump
closure into the aft housing sump.
DESCRIPTION: The Pusher consists of a triangular plate, pusher plate, and
a hydraulic cylinder, all used to seat the sump closure. The tool has
a black oxide or black phosphate finish.
DIMENSIONS: 14 x 17 in. (356 x 432 mm).
WEIGHT: 30 lb (14 kg).
SUPPORTING TOOLS: Hydraulic Hand Pump, 0.375 in. Connector, 2C14073.
TOOL MAINTENANCE: Apply corrosion preventive oil to all surfaces that
have black oxide or black phosphate coating.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing 2C14190.
FOR ALL
2C14190G03
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C14190G03
Page 2
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
PUSHER, SUMP CLOSURE, FORWARD BEARING NO. 5R
2C14190G04
PURPOSE AND USE: The Pusher is used to install the No. 5R forward sump
closure into the aft housing sump.
DESCRIPTION: The Pusher consists of a triangular plate, pusher plate, and
a hydraulic cylinder, all used to seat the sump closure. The tool has
a black oxide or black phosphate finish.
DIMENSIONS: 14 x 17 in. (356 x 432 mm).
WEIGHT: 30 lb (14 kg).
SUPPORTING TOOLS: Hydraulic Hand Pump, 0.375 in. Connector, 2C14073.
TOOL MAINTENANCE: Apply corrosion preventive oil to all surfaces that
have black oxide or black phosphate coating.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing 2C14190.
FOR ALL
2C14190G04
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C14190G04
Page 2
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
STAND, SHIPPING/STORAGE HIGH PRESSURE TURBINE MODULE
2C14193G03
FOR ALL
2C14193G03
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C14193G03
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
TOOL STARTING AND STRAIGHTENING RETAINERS C/R BLADES STAGE 1
2C14198G02
FOR ALL
2C14198G02
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C14198G02
Page 2
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FIXTURE, INSTALL AND REMOVE - HP TURBINE MODULE ASSEMBLY
2C14199G07
PURPOSE AND USE: The Install and Remove Fixture is used to align the rotor
and to support the high pressure turbine stator to allow for installation
and removal of the high pressure turbine module.
DESCRIPTION: The Install and Remove Fixture consists of an anti-rotation frame,
several tubes (pushing, pulling, guide, etc.) and adapters. The primary color of
the tool is blue. This tool is applicable to all CF6-80C2 engines, except B8F.
DIMENSIONS: 42.25 x 52 in. (1,073 x 1,320 mm).
WEIGHT: 390 lbs (177 kg).
SUPPORTING TOOLS: Sweeney Torque Multiplier 8100 and 8102, 2C14220.
TOOL MAINTENANCE: Apply corrosion preventive oil to all surfaces that
have black oxide or black phosphate coating.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing 2C14199.
PURPOSE AND USE: The Install and Remove Fixture is used to align the rotor
and to support the high pressure turbine stator to allow for installation
and removal of the high pressure turbine module.
DESCRIPTION: The Install and Remove Fixture consists of an anti-rotation frame,
several tubes (pushing, pulling, guide, etc.) and adapters. The primary color of
the tool is blue. This tool is applicable to all CF6-80C2 engines.
DIMENSIONS: 42.25 x 52 in. (1,073 x 1,320 mm).
WEIGHT: 390 lbs (177 kg).
SUPPORTING TOOLS: Sweeney Torque Multiplier 8100 and 8102, 2C14220.
TOOL MAINTENANCE: Apply corrosion preventive oil to all surfaces that
have black oxide or black phosphate coating.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing 2C14199.
FOR ALL
2C14199G08
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C14199G08
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
ADAPTER SET, PEDESTAL - COMPRESSOR REAR FRAME
2C14203G01
PURPOSE AND USE: To use with engine supports 2C6339 during maintenance operations
and storage of the engine or its subassemblies.
DESCRIPTION: Consists of two flat plates with a bolt pattern to interface with
the CRF forward flange and engine support pedestals.
DIMENSIONS: 13 x 7 x 0.625 in. (330 x 178 x 16 mm).
WEIGHT: 19 lb (9 kg).
SUPPORTING TOOLS: Support, 2C6339G01 and G03.
TOOL MAINTENANCE: Coat treated surfaces (black oxide or black phosphate) with
corrosion preventive light oil when stored. Load test periodically (see GE
drawing 2C14203 for load test diagram and applicable NOTE).
QUANTITY PER OPERATION: One set.
REPLACEMENT PARTS LIST
GROUP PART NO. NOMENCLATURE QUANTITY SUPPLIER
NUMBER CODE
G01 2C14203P02 Bracket 2
2C14203P05 Washer 24
0.375-16UNC-3AX2.0 12 Pt. Cap Screw 12 CW
FOR ALL
2C14203G01
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C14203G01
Page 2
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
DELETED
2C14204G02
PURPOSE AND USE: This tool has been deleted in its entirety.
FOR ALL
2C14204G02
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
STAND, ASSEMBLY, LOW PRESSURE TURBINE MODULE
2C14208G06
PURPOSE AND USE: The Low Pressure Turbine (LPT) Module Assembly Stand is used to
allow stacking of rotor and stator components for the 360 degree low pressure
turbine case and provide inspection capability of shrouds and interstage seals.
DESCRIPTION: The Low Pressure Turbine Module Assembly Stand consists of a
rectangular frame and an aft restraining ring with a center hub and inspection
post. The primary color of the tool is blue.
DIMENSIONS: 50 x 46 x 40 in. (1270 x 1168 x.1016 mm).
WEIGHT: 1000 lb (454 kg).
SUPPORTING TOOLS: 2C14215, 2C14216, 2C14218, 2C6168.
TOOL MAINTENANCE: Do an inspection and check the calibration of the tool
periodically. Refer to drawing 2C14208. Apply corrosion preventive oil to all
surfaces that have black oxide or black phosphate coating.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing 2C14208.
FOR ALL
2C14208G06
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C14208G06
Page 2
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
DOLLY, TRANSPORTATION/STORAGE - LOW PRESSURE TURBINE MODULE
2C14209G04
PURPOSE AND USE: To transport and store the low pressure turbine module
and permit attachment of the turbine rear frame.
DESCRIPTION: Consists of a frame with a pilot ring for attaching the stage 1
low pressure turbine nozzle assembly or stage 1 dummy nozzle, a screw jack with
a pilot to engage the low pressure turbine shaft, and a dial indicator for
monitoring axial movement. Casters and floor locks also provided.
DIMENSIONS: 60 x 60 x 25 in. (1524 x 1524 x 635 mm).
WEIGHT: 500 lb (227 kg).
SUPPORTING TOOLS: Fixtures - 2C14214G01, 2C14218G0l.
TOOL MAINTENANCE: Coat treated surfaces (black oxide or black phosphate)
with corrosion preventive light oil when stored.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS LIST
GROUP PART NO. NOMENCLATURE QUANTITY SUPPLIER
NUMBER CODE
G04 2C14209P02 Base 1
2C14209P03 Top Plate 1
2C14209P06 Bottom Plate 1
2C14209P07 Gage Plate 1
2C14209P08 Spacer 1
2C14209P09 Screw 2
2C14209P10 Shaft 1
2C14209P11 Socket 1
2C14209P12 Bracket 1
2C14209P33 Bolt 2
2C14209P36 Clamp 1
2C14209P37 Center Post 1
C00-01-001 Floor Lock 2 O
12-TM-06201-S Caster 4 AI
NY-01-SL120000
25496 J2-UNI-LIFT Worm Gear Actuator 1 CZ
with fixed screw and
traveling nut
D81T with Rev. 2.00 Dial Indicator 1 AV
Range counter
AD-87 Split Collet 1 AV
PT-155 Indicator Point 1 AV
FOR ALL
2C14209G04
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
GROUP PART NO. NOMENCLATURE QUANTITY SUPPLIER
NUMBER CODE
1095K11 (1/8 NPT) Grease Fitting 1 R
FOR ALL
2C14209G04
Page 2
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C14209G04
Page 3
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
ADAPTER, LIFT - COMBUSTOR AND STAGE 1 OR 2 HPT NOZZLE
2C14219G01
PURPOSE AND USE: To provide horizontal lift capability for the combustor
and Stage 1 or 2 HPT nozzle lift adapters.
DESCRIPTION: Consists of an "L" shaped lift adapter with a series of holes
for center of gravity adjustment, a link for hoist attachment and ball lock
pin for attaching other fixtures and adapters.
DIMENSIONS: 26 x 13 x 3 in. (660 x 330 x 76 mm).
WEIGHT: 8 lb (4 kg).
SUPPORTING TOOLS: Fixtures - 2C14122G01 and 2C6810G01; Adapters -
2C14121G01 and 2C14205G01; Overhead Hoist.
TOOL MAINTENANCE: Coat treated surfaces (black oxide or black phosphate) with
corrosion preventive light oil when stored. Load test periodically (see GE
drawing 2C14219 for load test diagram and applicable NOTE).
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS LIST
GROUP PART NO. NOMENCLATURE QUANTITY SUPPLIER
NUMBER CODE
G01 2C14219P02 Lift Adapter 1
S-209- 1 Ton Shackle 1 CQ
S-341-4200 lb Link 1 CQ
BLC4BC30SL10 Ball-Lock Pin 1 A
FOR ALL
2C14219G01
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C14219G01
Page 2
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FIXTURE, LIFT - HP TURBINE HORIZONTAL
2C14220G01
PURPOSE AND USE: To lift the high pressure turbine rotor and tooling (2C14199)
horizontally during installation and removal.
DESCRIPTION: Consists of an "L" shaped lift adapter which attaches to
the support shaft of fixture 2C14199G01. An adjustable lift eye allows
for center of gravity adjustments.
DIMENSIONS: 10 x 30 x 40 in. (254 x 762 x 1016 mm).
WEIGHT: 150 lb (68 kg).
SUPPORTING TOOLS: (Min. 1 Ton) two overhead cranes; Fixture, 2C14199G02.
TOOL MAINTENANCE: Coat treated surfaces (black oxide or black phosphate) with
corrosion preventive light oil when stored. Load test periodically (see GE
drawing 2C14220 for load test diagram and applicable NOTE).
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS LIST
GROUP PART NO. NOMENCLATURE QUANTITY SUPPLIER
NUMBER CODE
G01 2C14220P02 Frame 1
2C14220P03 Frame Cap 1
2C14220P04 Frame Dolly 2
2C14220P05 Threaded Rod 1
2C14220P06 Spacer 1
2C14220P07 Swivel Nut 1
2C14220P08 Hand Crank 1
2C14220P09 Threaded Bushing 2
2C14220P10 Spacer 2
2C14220P11 Wear Strip 1
2C14220P12 Wear Strip 1
2C14220P13 Spacer 2
2C14220P14 Washer 4
2C14220P15 Shoulder Bolt 2
2C14220P16 Scale 2
2C14220P17 Swing Bolt 2
CL-5-HK-6 Hand Knob 2 I
31718 Dowel Pin 4 I
G-2130 Shackle 1 S
CL-120-HR Hoist Ring 1 I
FOR ALL
2C14220G01
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C14220G01
Page 2
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
STAND, INSTALL/REMOVE - HPT TURBINE ROTOR SHAFT SEALS AND BEARING RACES
2C14222G01
PURPOSE AND USE: To support the high pressure turbine module when fixture
2C14199P02 is attached for the purpose of installing/removing high pressure
turbine forward shaft seals and bearing races.
DESCRIPTION: Consists of a tubular base having four supports and clamps to hold the
HPT module when supported in 2C14199 support frame, and a forward yoke to support
the forward HPT rotor shaft. Four casters and floor locks are provided.
DIMENSIONS: 41 x 53 x 30 in. (1041 x 1346 x 762 mm).
WEIGHT: 150 lb (68 kg).
SUPPORTING TOOLS: Fixtures - 2C14220G01, 2C14199G01.
TOOL MAINTENANCE: Coat treated surfaces (black oxide or black phosphate)
with corrosion preventive light oil when stored.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS LIST
GROUP PART NO. NOMENCLATURE QUANTITY SUPPLIER
NUMBER CODE
G01 2C14222P02 Frame 1
2C14222P03 Clevis 1
2C14222P04 Arm 1
2C14222P05 Arm 1
2C14222P06 Swing Bolt 1
2C14222P07 Pad 2
2C14222P24 Tag 2
12-TM-06201-S-NY Caster 4 AI
01-SL-120000
C00-01-001 Floor Lock 2 O
CL-7-KSA-N Knob Shoe Assy 4 I
CL-4-HK-4 Hand Knob 1 I
CL-2-SWA-1 Swing Clamp Assy 4 I
91151A029 Bevel Washer 4 R
FOR ALL
2C14222G01
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C14222G01
Page 2
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
ADAPTER SET, PEDESTAL - LOW PRESSURE TURBINE MODULE, FORWARD
2C14224G02
PURPOSE AND USE: To use with engine supports 2C6339 during maintenance and storage
to provide support for the LPT module at the forward end. The adapters also
interface with overhead rail supports for lifting the LPT module.
DESCRIPTION: Consists of two adapters having a six bolt hole pattern to interface
with the forward flange of the LPT forward stator case and two slots on the
opposite end to interface with the engine support pedestals.
DIMENSIONS: 14 x 6 x 0.625 in. (356 x 153 x 16 mm).
WEIGHT: 18 lb (8 kg).
SUPPORTING TOOLS: Fixture - 2C6339G03/G05.
TOOL MAINTENANCE: Treated surfaces (black oxide or black phosphate) with
corrosion preventive light oil when stored. Load test periodically (see GE
drawing 2C14224 for load test diagram and applicable NOTE).
QUANTITY PER OPERATION: One set.
REPLACEMENT PARTS LIST
GROUP PART NO. NOMENCLATURE QUANTITY SUPPLIER
NUMBER CODE
G02 2C14224P03 Washer 12
2C14224P06 Bracket 2
FOR ALL
2C14224G02
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C14224G02
Page 2
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
DOLLY, SUB-ASSEMBLY - FRAME
2C14227G02
PURPOSE AND USE: The Sub-Assembly Dolly is used to support the various frame
subassemblies while performing various maintenance operations or services. The
Sub-Assembly Dolly will also serve as a temporary storage for the frames.
DESCRIPTION: The Subassembly Dolly consists of a base on wheels with a triangular,
upright tubular frame welded on each end with revolving trunnions so the frames
may be rotated 360 degrees. The primary color of the tool is blue.
DIMENSIONS: 90 x 45 x 60 in. (2,286 x 1,143 x 1,524 mm).
WEIGHT: 600 lbs (272 kg).
SUPPORTING TOOLS: 2C14015, 2C14082, 2C14087, 2C6169, 2C6204, 2C6218,
2C6223, and 2C14643 to the supporting tools.
TOOL MAINTENANCE: Apply corrosion preventive oil to all surfaces that
have black oxide or black phosphate coating.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing 2C14227.
FOR ALL
2C14227G02
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C14227G02
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
HOSE, TEST - FAN REVERSER
2C14228P01
PURPOSE AND USE: The Test Hose is used to supply an air pressure connection to the
left hand fan reverser center actuator during fan reverser ground testing.
DESCRIPTION: The Test Hose is a 146 in. (3708 mm) long hose with fittings
on each end. One end attaches to the air starter duct and the other
end attaches to the fan reverser.
DIMENSIONS: 1.5 x 144 in. (38 x 3658 mm).
WEIGHT: 18 lb (8 kg).
SUPPORTING TOOLS: None.
TOOL MAINTENANCE: None.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing 2C14228.
FOR ALL
2C14228P01
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C14228P01
Page 2
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
GAGE SET, CONCENTRICITY, COMPRESSOR REAR FRAME AFT SEALS
2C14229G02
PURPOSE AND USE: The Concentricity Gage Set is used with 2C14175 to runout
the seals and other concentric structures in the compressor rear frame prior
to high pressure turbine (HPT) rotor installation.
DESCRIPTION: The Concentricity Gage consists of an aluminum collar which clamps
around the 2C14175 retaining sleeve and is the base to which the support post and
other adapters are mounted. The tool has a black oxide or black phosphate finish.
DIMENSIONS: 24 x 12 x 6 in. (610 x 305 x 152 mm).
WEIGHT: 20 lb (9 kg).
SUPPORTING TOOLS: 2C14175.
TOOL MAINTENANCE: Do an inspection and check the calibration of the tool
periodically. Refer to drawing 2C14229. Apply corrosion preventive oil to all
surfaces that have black oxide or black phosphate coating.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing 2C14229.
FOR ALL
2C14229G02
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C14229G02
Page 2
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
TOOL KIT, REMOVAL - THERMAL SHIELD HOOK BOLT
2C14238G02
PURPOSE AND USE: The Removal Tool Kit is used to remove the hook bolts in the high
pressure turbine (HPT) thermal shield without damaging the thermal shield.
DESCRIPTION: The Removal Tool Kit consists of four pairs of modified pliers.
DIMENSIONS: 10 x 5 x 1 in. (254 x 127 x 25 mm).
WEIGHT: 2 lb (1 kg).
SUPPORTING TOOLS: None.
TOOL MAINTENANCE: TBD
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing 2C14238.
FOR ALL
2C14238G02
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C14238G02
Page 2
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FIXTURE, RUNOUT - HIGH PRESSURE TURBINE ROTOR AFT FLANGE
2C14239G03
PURPOSE AND USE: The Runout Fixture is used to indicate a twelve point runout on the
outside diameter of the aft end of the high pressure turbine rotor (HPTR).
DESCRIPTION: The Runout Fixture consists of a wide channel that bolts across the
stage 2 high pressure turbine (HPT) nozzle aft flange or compressor rear frame aft
flange, a magnetic base indicator holder and an indicator with .0001 in graduations.
A container is provided. The tool has a black oxide or black phosphate finish.
DIMENSIONS: 40 x 12 x 6 in. (1016 x 305 x 152 mm).
WEIGHT: 20 lb (9 kg).
SUPPORTING TOOLS: 2C14240.
TOOL MAINTENANCE: Do an inspection and check the calibration of the tool
periodically. Refer to drawing 2C14239. Apply corrosion preventive oil to all
surfaces that have black oxide or black phosphate coating.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing 2C14239.
FOR ALL
2C14239G03
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C14239G03
Page 2
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
GAGE SET, INSPECTION - HIGH PRESSURE TURBINE INTERSTAGE STATIONARY SEAL
2C14246G01
PURPOSE AND USE: To inspect the HPT interstage seal honeycomb cells after the seals
have been ground to assure an adequate braze free cell depth exists.
DESCRIPTION: The gage set consists of three step pin gages sized to
meet final acceptance criteria.
DIMENSIONS: 6 x 4 x 2 in. (152 x 102 x 51 mm).
WEIGHT: 2 lb (0.9 kg).
SUPPORTING TOOLS: None.
TOOL MAINTENANCE: Lightly coat black oxide or black phosphate surfaces
with corrosion preventive oil.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS LIST
GROUP PART NO. NOMENCLATURE QUANTITY SUPPLIER
NUMBER CODE
G01 2C14246P02 Step Plug 1
2C14246P03 Step Plug 1
2C14246P04 Step Plug 1
2C14246P05 Gage Handle 1
2C14246P06 Gage Handle 1
2C14246P07 Gage Handle 1
2C14246P08 Container 1
FOR ALL
2C14246G01
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C14246G01
Page 2
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
PLATFORM, SUPPORT - HIGH PRESSURE TURBINE ROTOR BUILD-UP
2C14250G01
PURPOSE AND USE: To support the high pressure turbine rotor build-up fixture
at a convenient height during rotor build-up.
DESCRIPTION: Consists of a platform and four rectangular tubular legs.
DIMENSIONS: 20 x 20 x 22 in. (508 x 508 x 559 mm).
WEIGHT: 125 lb (57 kg).
SUPPORTING TOOLS: Build-up Fixture, 2C14011.
TOOL MAINTENANCE: None.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: None required.
FOR ALL
2C14250G01
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C14250G01
Page 2
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FIXTURE, ALIGNMENT - HIGH PRESSURE TURBINE ROTOR IMPELLER COVER
2C14261G01
PURPOSE AND USE: To align the impeller cover for minimum run-out during
high pressure turbine rotor build-up.
DESCRIPTION: Consists of a steel circular ring with three rabbet diameters.
It has four tapped holes for jack screws to aid in disassembly of the
engine hardware from the fixture.
DIMENSIONS: 26 in. dia x 1 in. (660 mm dia x 25 mm).
WEIGHT: 21 lb (10 kg).
SUPPORTING TOOLS: None required.
TOOL MAINTENANCE: Coat treated surfaces (black oxide or black phosphate)
with corrosion preventive light oil when stored.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS LIST
GROUP PART NO. NOMENCLATURE QUANTITY SUPPLIER
NUMBER CODE
G01 2C14261P02 Alignment Ring 1
2C14261P03 Jack Screw 4
FOR ALL
2C14261G01
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C14261G01
Page 2
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
GAGE, INSPECTION - FAN SHAFT TO HPT STATOR CASE
2C14276G01
PURPOSE AND USE: To measure the drop ("AE") dimension from the fan
midshaft aft shoulder to the HPT stator case aft flange so that shims
may be installed on the LPT shaft.
DESCRIPTION: This set consists of a black oxided 4130/4142 steel gage bar and a
L.S. Starrett Co. Vernier depth gage in a reusable container.
DIMENSIONS: 7.5 x 38.3 x 2 in. (191 x 973 x 51 mm).
WEIGHT: 50 lb (23 kg).
SUPPORTING TOOLS: None.
TOOL MAINTENANCE: None.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS LIST
GROUP PART NO. NOMENCLATURE QUANTITY SUPPLIER
NUMBER CODE
G01 2C14276P02 Bar, Gage 1
FOR ALL
2C14276G01
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C14276G01
Page 2
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FIXTURE, POSITION - FUEL NOZZLE
2C14280G02
PURPOSE AND USE: To restrain the fuel nozzle fittings at the proper attitude
with respect to the engine centerline while the screws that attach the
nozzles to the compressor rear frame are torqued.
DESCRIPTION: The fixture consists of a 30 degree segment with three locator holes
located 12 degrees apart. For each locator hole there is a knurled alignment
plug. The alignment plug is locked in place by a thumb screw.
DIMENSIONS: 2 x 3 x 10 in. (51 x 76 x 254 mm).
WEIGHT: 2 lb (0.9 kg).
SUPPORTING TOOLS: None.
TOOL MAINTENANCE: Lightly coat black oxide surfaces with corrosion preventive oil.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS LIST
GROUP PART NO. NOMENCLATURE QUANTITY SUPPLIER
NUMBER CODE
G02 2C14280P02 Body 1
2C14280P03 Clamp Screw 3
2C1428OP05 Centering Plug 3
FOR ALL
2C14280G02
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C14280G02
Page 2
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
ADAPTER KIT, LUBE AND DRYOUT - ENGINE BEARING
2C14283G01
PURPOSE AND USE: The Lube and Dryout Adapter Kit is used to connect the engine start
cart to the lube and scavenge pump to dry moisture out of the engine bearings and
sumps and lubricate the bearings while they are still hot and dry.
DESCRIPTION: The Lube and Dryout Adapter Kit has a manifold and an oil
container connected to each other and the engine by five hose assemblies.
The primary color of the tool container is blue.
DIMENSIONS: Container, 20 x 20 x 20 in. (508 x 508 x 508 mm).
WEIGHT: 30 lb (14 kg).
SUPPORTING TOOLS: Engine Start Cart.
TOOL MAINTENANCE: TBD
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing 2C14283.
FOR ALL
2C14283G01
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C14283G01
Page 2
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
ADAPTER, CABLE - HMU TO MEC ENGINE PRESERVATION UNIT
2C14286G01
PURPOSE AND USE: The Adapter Cable is used to adapt the engine preservation unit,
2C14974, to also work with the main engine control (MEC) on PMC-type engines.
DESCRIPTION: The Adapter Cable is a Y-shaped cable with labeled connectors on
each end. Steel items have a black oxide or black phosphate finish.
DIMENSIONS: 2 x 19 in. (51 x 483 mm).
WEIGHT: 2 lbs (1 kg).
SUPPORTING TOOLS: 2C14974.
TOOL MAINTENANCE: TBD
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing 2C14286.
FOR PMC
2C14286G01
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR PMC
2C14286G01
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
DELETED
2C14287G01
PURPOSE AND USE: This tool has been deleted in its entirety.
FOR ALL
2C14287G01
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FIXTURE, LIFT/TURN COMPRESSOR ROTOR SPOOLS
2C14288G01
PURPOSE AND USE: This fixture is used to lift and turn the compressor
rotor from stages 10 thru 14 spool/shaft and the stages 3 thru 9 spool
vertically and horizontally.
DESCRIPTION: The lift fixture consists of an aluminum lift plate with four
equally spaced triangular access holes. There are four equally spaced attachment
pads bolted on one face plate near the outer circumference.
DIMENSIONS: 11 x 11 x 25 in. (279 x 279 x 635 mm).
WEIGHT: 15 lbs (6.8 kg).
SUPPORTING TOOLS: Used with 2C14014G01, and an overhead hoist
with capacity 0.5 ton (454 kg).
TOOL MAINTENANCE: Apply corrosion preventive oil to all surfaces
that have black oxide finish.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing 2C14288.
FOR ALL
2C14288G01
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C14288G01
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
ADAPTER, TORQUE
2C14290G01
PURPOSE AND USE: This fixture is used to break the torque on the forward
flange of the stage 1 stationary seal.
DESCRIPTION: This tool consists of an offset 0.5 in. square drive extension and
special reduced outside diameter #14 spline socket (fits also 7/16 12 point).
DIMENSIONS: 6 x 1 x 1 in. (152 x 25 x 25 mm).
WEIGHT: 0.5 lb (0.23 kg).
SUPPORTING TOOLS: Breaker bar.
TOOL MAINTENANCE: Apply corrosion preventive oil to all surfaces
that have black oxide finish.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing 2C14290.
FOR ALL
2C14290G01
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C14290G01
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
TOOL ASSEMBLY, LIFT - LPT NOZZLE STAGE 2, STAGE 3, STAGE 4 AND STAGE 5
2C14292G01
PURPOSE AND USE: This fixture is used to lift the low pressure turbine assembly
nozzles stages 2 thru 5 for installation into the case.
DESCRIPTION: This tool is a collector drawing of four aluminum fixtures:
9481M58G01, 9481M59G01, 9481M60G01 and 9481M61G01.
DIMENSIONS: 52.25 in. dia x 11 in. (1328.2 mm. dia x 279 mm).
WEIGHT: 310 lbs (141 kg).
SUPPORTING TOOLS: 2C14295, 9481M58G01, 9481M59G01, 9481M60G01, and 9481M61G01.
TOOL MAINTENANCE: Not required.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing 2C14292.
FOR ALL
2C14292G01
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C14292G01
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
TOOL, INSTALLATION - SLABBED HEAD SHOULDER BOLTS, LPT ROTOR STAGE 2
2C14293G01
PURPOSE AND USE: This fixture is used to install the slabbed head shoulder
bolts in the low pressure turbine rotor stage 2 disk.
DESCRIPTION: The tool is a set of pliers that consists of two jaws made of
black oxide steel coated with plastisol on the handles and nylon on the ends to
avoid damage to the engine hardware. One of the jaws is slotted to straddle
the bolt shank to react against the LPTR stage 2 disk.
DIMENSIONS: 3.5 x 11.5 x 1 in. (89 x 292 x 25 mm).
WEIGHT: 2 lbs (0.91 kg).
SUPPORTING TOOLS: N/A.
TOOL MAINTENANCE: Apply corrosion preventive oil to all surfaces
that have black oxide finish.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing 2C14293.
FOR ALL
2C14293G01
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C14293G01
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
TOOL SET, ALIGN/INSTALLATION - TUBE, AIR STAGE 1, LPT
2C14294G01
PURPOSE AND USE: This fixture is used to align the holes in the nozzle segments
and impingement cover for ease of installation of the air tube.
DESCRIPTION: The tool consists of an alignment rod, stored in
a commercial container.
DIMENSIONS: 24 x 4 x 4 in. (610 x 102 x 102 mm).
WEIGHT: 2.5 lbs (1.1 kg).
SUPPORTING TOOLS: Mallet.
TOOL MAINTENANCE: N/R.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing 2C14294.
FOR ALL
2C14294G01
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C14294G01
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FIXTURE, BUILD UP - LPT NOZZLE STAGE 2 THRU 5
2C14295G01
PURPOSE AND USE: To orient the nozzle segments during build up for case
installation of the nozzle assembly as one 360 degrees unit.
DESCRIPTION: The fixture consists of a stages 2 thru 5 plate, spacer plate,
separator plate, supporting ring, lug, and swivel hoist ring.
DIMENSIONS: N/A.
WEIGHT: N/A.
SUPPORTING TOOLS: N/A.
TOOL MAINTENANCE: Apply corrosion preventive oil to all surfaces
that have black oxide finish.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing 2C14295
FOR ALL
2C14295G01
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C14295G01
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
COVER – PRIMARY NOZZLE
2C14296G01
PURPOSE AND USE: This fixture is used to cover and protect the primary nozzle.
DESCRIPTION: The cover consists of a ring made of a rigid red
urethane reinforced with glass matt.
DIMENSIONS: 3.5 in. x 52 in. dia (89 mm x 1,321 mm dia).
WEIGHT: 12 lbs (5 kg).
SUPPORTING TOOLS: None.
TOOL MAINTENANCE: Not required.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing 2C14296.
FOR ALL
2C14296G01
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C14296G01
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
DELETED
2C14600G01
PURPOSE AND USE: This tool has been deleted in its entirety.
FOR ALL
2C14600G01
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
DELETED
2C14602G03
PURPOSE AND USE: This tool has been deleted in its entirety.
Superseded by tool 2C14602G04.
FOR ALL
2C14602G03
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FIXTURE, RESTRAIN - TURBINE REAR FRAME TO LOW PRESSURE TURBINE ROTOR
2C14602G04
PURPOSE AND USE: The Restrain Fixture is used to prevent the low pressure turbine
(LPT) rotor to the turbine rear frame to maintain the correct rotor/stator
relationship during installation, removal and handling of the LPT module.
DESCRIPTION: The Restrain Fixture consists of a strongback, adjusting
nut, jam nut, and a pilot tube. The pilot tube has internal threads
on the forward end and external threads on the aft end. The primary
color of the tool is either green or black.
DIMENSIONS: 30 x 28 in. (762 x 711 mm).
WEIGHT: 130 lbs (59 kg).
SUPPORTING TOOLS: 2C1402G04, 2C14052, 2C14092, 2C14093, 2C14132,
2C18004, 2C18008, and 2C18010.
TOOL MAINTENANCE: Apply corrosion preventive oil to all surfaces that
have black oxide or black phosphate coating.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing 2C14602.
FOR ALL
2C14602G04
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C14602G04
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FIXTURE, ASSEMBLY - BOOSTER STATOR, STAGE 1
2C14605G01
PURPOSE AND USE: This fixture is used to support the fan stator and
its component parts during assembly.
DESCRIPTION: This fixture includes a base plate three support rings,
twenty-two mounting pads, rods and pressure plates.
DIMENSIONS: N/A.
WEIGHT: N/A.
SUPPORTING TOOLS: N/A.
TOOL MAINTENANCE: Apply corrosion preventive oil to all surfaces
that have black oxide finish.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing 2C14605.
FOR ALL
2C14605G01
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C14605G01
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
PUSHER - NO. 6 BEARING INNER RACE AND SEAL
2C14610G01
PURPOSE AND USE: To provide force required to seat No. 6 bearing oil seal and
No. 6 bearing inner race on low pressure turbine rotor shaft.
DESCRIPTION: The pusher consists of a threaded tube with plate welded to the
aft end. An extension bar is welded to the center of the plate. The pusher
is also used with a spacer to seat the bearing oil seal.
DIMENSIONS: 8.75 in. dia x 11 in. (222 mm dia x 279 mm).
WEIGHT: 3 lb (1 kg).
SUPPORTING TOOLS: 0.5 in. square male drive torque wrench.
TOOL MAINTENANCE: Coat treated surfaces (black oxide or black phosphate)
with corrosion preventive light oil when stored.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS LIST
GROUP PART NO. NOMENCLATURE QUANTITY SUPPLIER
NUMBER CODE
G01 2C14610P02 Spacer 1
2C14610P03 Torque Sleeve 1
FOR ALL
2C14610G01
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C14610G01
Page 2
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
DELETED
2C14612G04
PURPOSE AND USE: This tool has been deleted in its entirety.
Superseded by tool 2C14612G05.
FOR ALL
2C14612G04
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
TOOL, INSTALLATION AND REMOVAL SUPPORTS CENTER VENT TUBE
2C14612G05
PURPOSE AND USE: The Installation and Removal Tool is used to remove and
install the center vent air tube support assemblies.
DESCRIPTION: The Center Vent Tube Support is used to torque the tube and
anti-torque tube with swing clamps operated by an extension shaft. The
tool has a black oxide or black phosphate finish.
DIMENSIONS: 6 x 105 in. (152 x 2,667 mm).
WEIGHT: 65 lbs (29 kg).
SUPPORTING TOOLS: Standard Torque Wrench, 3/4 in. Drive Ratchet.
TOOL MAINTENANCE: Apply corrosion preventive oil to all surfaces that
have black oxide or black phosphate coating.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing 2C14612.
FOR ALL
2C14612G05
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C14612G05
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FIXTURE, RESTRAIN - LOW PRESSURE TURBINE ASSEMBLY AFT
2C14614G01
PURPOSE AND USE: The Restrain Fixture is used to hold the correct stator/
rotor position of the low pressure turbine module during transfer
to and from the balance area.
DESCRIPTION: The Restrain Fixture is a ring with six spokes that attach the outer
hub to the center hub. A nut is located in the center hub to attach the low
pressure turbine rotor (LPTR) shaft. The primary color of the tool is blue.
DIMENSIONS: 55 x 25 in. (1397 x 635 mm).
WEIGHT: 290 lb (132 kg).
SUPPORTING TOOLS: Hoist, 2C14208, 2C14209.
TOOL MAINTENANCE: Apply corrosion preventive oil to all surfaces that
have black oxide or black phosphate coating.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing 2C14614.
FOR ALL
2C14614G01
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C14614G01
Page 2
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
DELETED
2C14615G01
PURPOSE AND USE: This tool has been deleted in its entirety.
FOR ALL
2C14615G01
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
DELETED
2C14616G01
PURPOSE AND USE: This tool has been deleted in its entirety.
FOR ALL
2C14616G01
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
PULLER, SUMP CLOSURE AND SEAL STATIONARY NO. 4R & 5R HEARINGS
2C14618G02
PURPOSE AND USE: To remove the No. 5R bearing sump closure and the
No. 4R and 5R bearing stationary oil seal.
DESCRIPTION: Consists primarily of a puller plate, pusher plate, circular cap,
hydraulic cylinder, and three rods which connect the plates to one of two puller
tubes. The puller tubes have tabs which engage the tabs on the No. 5R bearing
sump closure or No. 4R and 5R bearing stationary oil seal.
DIMENSIONS: 14.5 in. dia x 20 in. (368 mm dia x 508 mm).
WEIGHT: 43 lb (20 kg).
SUPPORTING TOOLS: Hydraulic hand pump, 0.375 connector, 2C14073G03
adapter and 2C14621G01 support.
TOOL MAINTENANCE: Coat treated surfaces (black oxide or black phosphate)
with corrosion preventive light oil when stored.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS LIST
GROUP PART NO. NOMENCLATURE QUANTITY SUPPLIER
NUMBER CODE
G02 2C14618P02 Plate 1
2C14618P03 Plate 1
2C14618P04 Puller 1
2C14618P06 Nut 1
2C14618P07 Handle 1
2C14618P08 Rod 1
2C14618P25 Puller 1
RC-101 Hydraulic Cylinder 1 D
FZ-1610 3/8 Female Elbow 1 D
AR-400 Coupler 1 D
SL-4 Spring Plunger 1 C
FZ-1614 1/4-20 x 1.00 lg Bar 1 D
FOR ALL
2C14618G02
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C14618G02
Page 2
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FIXTURE, LIFT/TURN - STAGE 1 FAN DISK AND STAGE 2-5 FAN ROTOR, FORWARD
2C14620G01
PURPOSE AND USE: To lift and turn either the stage 1 fan disk or the
stage 2-5 fan rotor from the forward end.
DESCRIPTION: Consists of an aluminum ring with four spokes, a load centering
eye bolt and pick-up bar. The aluminum ring bolts to the forward end of
either the stage 1 fan disk or stage 2-5 fan rotor.
DIMENSIONS: 36 x 50 x 6 in. (914 x 1270 x 152 mm).
WEIGHT: 40 lb (18 kg).
SUPPORTING TOOLS: Overhead Hoist; Fixture, 2C14633.
TOOL MAINTENANCE: Coat treated surfaces (black oxide or black phosphate) with
corrosion preventive light oil when stored. Load test periodically (see GE
drawing 2C14620 for load test diagram and applicable NOTE).
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS LIST
GROUP PART NO. NOMENCLATURE QUANTITY SUPPLIER
NUMBER CODE
G01 2C14620P02 Ring 1
2C14620P03 Pick-up Bar 1
2C14620P04 Eye Bolt 1
FOR ALL
2C14620G01
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C14620G01
Page 2
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
DELETED
2C14628G01
PURPOSE AND USE: This tool has been deleted in its entirety.
FOR ALL
2C14628G01
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FIXTURE, LIFT AND ROTATION - FAN MAINTENANCE UNIT
2C14629G01
PURPOSE AND USE: The Lift and Rotation Fixture is used to support the forward end of
the maintenance unit when rotating from the vertical to the horizontal position.
DESCRIPTION: The Lift and Rotation Fixture consists of a support assembly,
a bar with a lift eye and two cables connected to the support assembly.
The primary color of the tool is blue.
DIMENSIONS: 7 x 11 x 57 in. (178 x 279 x 1448 mm).
WEIGHT: 60 lb (27 kg).
SUPPORTING TOOLS: Overhead Crane, 2C6350.
TOOL MAINTENANCE: Apply corrosion preventive oil to all surfaces that
have black oxide or black phosphate coating.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing 2C14629.
FOR ALL
2C14629G01
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C14629G01
Page 2
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FIXTURE, LIFT AND ROTATION - FAN MAINTENANCE UNIT
2C14629G02
PURPOSE AND USE: The Lift and Rotation Fixture is used to support the forward end of
the maintenance unit when rotating from the vertical to the horizontal position.
DESCRIPTION: The Lift and Rotation Fixture consists of a support assembly,
a bar with a lift eye and two cables connected to the support assembly.
The primary color of the tool is blue.
DIMENSIONS: 7 x 11 x 57 in. (178 x 279 x 1448 mm).
WEIGHT: 60 lb (27 kg).
SUPPORTING TOOLS: Overhead Crane, 2C6350.
TOOL MAINTENANCE: Apply corrosion preventive oil to all surfaces that
have black oxide or black phosphate coating.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing 2C14629.
FOR ALL
2C14629G02
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C14629G02
Page 2
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
DELETED
2C14632G01
PURPOSE AND USE: This tool has been deleted in its entirety.
FOR ALL
2C14632G01
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
DELETED
2C14633G01
PURPOSE AND USE: This tool has been deleted in its entirety.
FOR ALL
2C14633G01
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FIXTURE, LIFT AND TURN - AFT FAN BOOSTER ROTOR
2C14633G03
PURPOSE AND USE: The Lift and Turn Fixture is used to lift and turn one of the two
the stage 2 thru 5 booster rotor spool or the entire fan rotor from the aft end.
DESCRIPTION: The Lift and Turn Fixture consists of a lift arm and a beam with an "L"
shaped clamp knurled knob on either end. The primary color of the tool is black.
DIMENSIONS: 50 x 6 x 15 in. (1,270 x 152 x 381 mm).
WEIGHT: 30 lbs (14 kg).
SUPPORTING TOOLS: Overhead Hoist, 2C14620.
TOOL MAINTENANCE: Apply corrosion preventive oil to all surfaces that
have black oxide or black phosphate coating.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing 2C14633.
FOR ALL
2C14633G03
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C14633G03
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
ADAPTER, MOTORING - CORE ENGINE
2C14635G01
PURPOSE AND USE: The Motoring Adapter is used to provide an adapter for
the motoring tool that motors the core engine through the accessory
gearbox starter pad for borescope inspection.
DESCRIPTION: The Motoring Adapter consists of a disk with a centering rabbet and a
splined spool. The tool has a black oxide or black phosphate finish.
DIMENSIONS: 9 x 9 x 14 in. (229 x 229 x 356 mm).
WEIGHT: 25 lb (11 kg).
SUPPORTING TOOLS: Sweeney 18901.
TOOL MAINTENANCE: Apply corrosion preventive oil to all surfaces that
have black oxide or black phosphate coating.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing 2C14635.
FOR ALL
2C14635G01
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C14635G01
Page 2
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FIXTURE, RESTRAIN - LPT ASSEMBLY AFT
2C14636G01
FOR ALL
2C14636G01
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C14636G01
Page 2
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
WRENCH, SPANNER - NO. 2 BEARING NUT, SEAL, GEAR
2C14637G01
FOR ALL
2C14637G01
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C14637G01
Page 2
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
CLOSURE SET, LEAK CHECK - TURBINE FRAME LUBE SYSTEM
2C14638G01
PURPOSE AND USE: The Leak Check Closure Set is used to check for leaks in the oil
supply and scavenge tubes of the assembled turbine rear frame sump and frame.
DESCRIPTION: The Leak Check Closure Set consists of a forward plate, an
aft plate (with provisions for a gage, relief valve, and a union), two
plugs, a tee cap with a pressure relief valve, and an oil cap. The tool
has a black oxide or black phosphate finish.
DIMENSIONS: 12.5 x 13 in. (318 x 330 mm).
WEIGHT: 20 lb (9 kg).
SUPPORTING TOOLS: None.
TOOL MAINTENANCE: Apply corrosion preventive oil to all surfaces that
have black oxide or black phosphate coating.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing 2014638.
FOR ALL
2C14638G01
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C14638G01
Page 2
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
DELETED
2C14638G02
PURPOSE AND USE: This tool has been deleted in its entirety.
FOR ALL
2C14638G02
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
TOOL SET, REMOVAL - MAGNETIC SEALS, AGB
2C14639G01
PURPOSE AND USE: To remove the magnetic seals from the drive pads of an assembled
installed accessory gearbox. Also to remove the adapter plates.
DESCRIPTION: This tool consists of two pullers and four jack screws. Jack
puller has a pusher plate, inner sleeve, a neoprene stop ring and an outer
sleeve. In the center is a screw assembly.
DIMENSIONS: 2.75 in. dia x 3.25 in. (70 mm dia x 83 mm).
WEIGHT: 4 lb (2 kg).
SUPPORTING TOOLS: None required.
TOOL MAINTENANCE: Coat treated surfaces (black oxide or black phosphate)
with corrosion preventive light oil when stored.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS LIST
GROUP PART NO. NOMENCLATURE QUANTITY SUPPLIER
NUMBER CODE
G01 2C14639P02 Puller 1
2C14639P03 Puller 1
2C14639P04 Sleeve 1
2C14939P05 Sleeve 1
2C14639P06 Stop Ring 1
2C14639P07 Stop Ring 1
2C14639P08 Pusher Plate 1
2C14639P09 Pusher Plate 1
2C14639P10 Screw 2
2C14639P11 Container 1
2C14639P12 Stop Ring 1
2C14639P13 Stop Ring 1
FOR ALL
2C14639G01
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C14639G01
Page 2
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
RETAINING CLIP SET, LPT SHROUDS
2C14641G01
PURPOSE AND USE: To hold shrouds in place during inspection and disk installation.
DESCRIPTION: This retaining clip set consists of 85 "C" shaped clips.
A container is provided for storage.
DIMENSIONS: 14 x 12 x 6 in. (356 x 305 x 153 mm).
WEIGHT: 5 lb (2.3 kg).
SUPPORTING TOOLS: None required
TOOL MAINTENANCE: Place clips in storage container if not in use.
QUANTITY PER OPERATION: One set.
REPLACEMENT PARTS LIST
GROUP PART NO. NOMENCLATURE QUANTITY SUPPLIER
NUMBER CODE
G01 2C14641P02 Stage 1 Shroud 17
Retainer
2C14641P03 Stage 2 Shroud 20
Retainer
2C14641P04 Stage 3 Shroud 24
Retainer
2C14641P05 Stage 4 Shroud 24
Retainer
2C14641P06 Container 1
FOR ALL
2C14641G01
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C14641G01
Page 2
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
PULLER, CAGE - FAN SPEED SENSOR AND NO. 2 BEARING INNER RACE
2C14642G01
PURPOSE AND USE: To remove the fan speed sensor cage and the No. 2 bearing inner
race from the forward fan shaft due to interference fit between the engine parts.
DESCRIPTION: The puller consists of six plunger pin assemblies, which are
attached to the puller housing. A hydraulic cylinder is installed to the
puller housing along with a puller plate (cylinder plate).
DIMENSIONS: 9 in. dia x 9 in. (229 mm dia x 229 mm).
WEIGHT: 30 lb (14 kg).
SUPPORTING TOOLS: Hydraulic Pump MSE-41 (2 people).
TOOL MAINTENANCE: Coat treated surfaces (black oxide or black phosphate)
with corrosion preventive light oil when stored.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS LIST
GROUP PART NO. NOMENCLATURE QUANTITY SUPPLIER
NUMBER CODE
G01 2C14642P02 Knob 6
2C14642P03 Plunger 6
2C14642P04 Housing 1
2C14642P05 Cylinder Plate 1
2C14642P06 Pusher Plate 1
2C14642P15 Guard 1
AR-400 Coupler 1 D
RC-104 Hydraulic Cylinder 1 D
CL-75W Spherical Washer 1 I
B2000-097 Belleville Spring 1 G
Washer
LC-026C-3 Compression Spring 6 L
FOR ALL
2C14642G01
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C14642G01
Page 2
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
BRACKET SET - ACCESSORY GEARBOX TO SUB-ASSEMBLY STAND
2C14643G02
PURPOSE AND USE: The Bracket Set is used to mount and support the accessory gearbox
in the sub-assembly stand 2C14644 and to the lift fixture 2C14645.
DESCRIPTION: The Bracket Set consists of two brackets, two adapter brackets
to interface with the lift fixture 2C14645, and an adjustable "L" shaped
plate to interface with the installation and removal fixture 2C14644.
The tool has a black oxide or black phosphate finish. This tool is
applicable to all CF6-80C2 engine models.
DIMENSIONS: 18.2 x 10 x 17.9 in. (462 x 254 x 455 mm).
WEIGHT: 57 lbs (26 kg).
SUPPORTING TOOLS: 2C14644, 2C14645.
TOOL MAINTENANCE: Apply corrosion preventive oil to all surfaces that
have black oxide or black phosphate coating.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing 2C14643.
FOR ALL
2C14643G02
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C14643G02
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
BRACKET SET - ACCESSORY GEARBOX TO SUB-ASSEMBLY STAND
2C14643G03
PURPOSE AND USE: The Bracket Set is used to mount and support the accessory gearbox
in the sub-assembly stand 2C14644 and to the lift fixture 2C14645.
DESCRIPTION: The Bracket Set consists of two brackets, two adapter brackets
to interface with the lift fixture 2C14645, and an adjustable "L" shaped
plate to interface with the installation and removal fixture 2C14644.
The tool has a black oxide or black phosphate finish. This tool is
applicable to CF6-80C2 engine model B6FA only.
DIMENSIONS: 18.2 x 10 x 17.9 in. (462 x 254 x 455 mm).
WEIGHT: 57 lbs (26 kg).
SUPPORTING TOOLS: 2C14644, 2C14645.
TOOL MAINTENANCE: Apply corrosion preventive oil to all surfaces that
have black oxide or black phosphate coating.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing 2C14643.
FOR B6FA
2C14643G03
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR B6FA
2C14643G03
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FIXTURE, INSTALLATION AND REMOVAL - ACCESSORY GEARBOX MODULE
2C14644G02
PURPOSE AND USE: The Installation and Removal Fixture is used to install
and remove the accessory gearbox module from the engine, with the
engine in the horizontal position.
DESCRIPTION: The Installation and Removal Fixture consists of a square base
frame with a pedestal protruding perpendicular to the base to meet the mount
of the accessory gearbox. The primary color of the tool is blue. This tool
is applicable to all CF6-80C2 engine models except B6FA.
DIMENSIONS: 54 x 39 x 21 in. (1,372 x 991 x 533 mm).
WEIGHT: 200 lbs (91 kg).
SUPPORTING TOOLS: 2C14084, 2C14643.
TOOL MAINTENANCE: Apply corrosion preventive oil to all surfaces that
have black oxide or black phosphate coating.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing 2C14644.
PURPOSE AND USE: The Installation and Removal Fixture is used to install
and remove the accessory gearbox module from the engine, with the
engine in the horizontal position.
DESCRIPTION: The Installation and Removal Fixture consists of a square base
frame with a pedestal protruding perpendicular to the base to meet the mount
of the accessory gearbox. The primary color of the tool is blue. This
tool is applicable to all CF6-80C2 engine models.
DIMENSIONS: 54 x 39 x 21 in. (1,372 x 991 x 533 mm).
WEIGHT: 200 lbs (91 kg).
SUPPORTING TOOLS: 2C14084, 2C14643.
TOOL MAINTENANCE: Apply corrosion preventive oil to all surfaces that
have black oxide or black phosphate coating.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing 2C14644.
FOR ALL
2C14644G03
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C14644G03
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FIXTURE, LIFT - ACCESSORY GEARBOX
2C14645G01
PURPOSE AND USE: The Lift Fixture is used to lift the accessory gearbox to and from
the subassembly stand (with or without accessories) and to and from the installation
and removal stand with the accessory gearbox in the horizontal position.
DESCRIPTION: The Lift Fixture is a tubular structure with center of gravity
adjustment capabilities in both directions. The primary color of the tool is blue.
DIMENSIONS: 62 x 16 x 4 in. (1575 x 406 x 102 mm).
WEIGHT: 106 lb (48 kg).
SUPPORTING TOOLS: Overhead Crane, 2C14643.
TOOL MAINTENANCE: Apply corrosion preventive oil to all surfaces that
have black oxide or black phosphate coating.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing 2C14645.
FOR ALL
2C14645G01
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C14645G01
Page 2
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FIXTURE, LIFT - ACCESSORY GEARBOX
2C14645G02
PURPOSE AND USE: The Lift Fixture is used to lift the accessory gearbox to and from
the subassembly stand (with or without accessories) and to and from the installation
and removal stand with the accessory gearbox in the horizontal position.
DESCRIPTION: The Lift Fixture is a tubular structure with center of gravity
adjustment capabilities in both directions. The primary color of the tool is blue.
DIMENSIONS: 62 x 16 x 4 in. (1575 x 406 x 102 mm).
WEIGHT: 106 lb (48 kg).
SUPPORTING TOOLS: Overhead Crane, 2C14643.
TOOL MAINTENANCE: Apply corrosion preventive oil to all surfaces that
have black oxide or black phosphate coating.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing 2C14645.
FOR ALL
2C14645G02
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C14645G02
Page 2
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
PULLER, NO. 6 BEARING INNER RACE AND SEAL
2C14646G01
PURPOSE AND USE: To remove the No. 6 bearing inner race and rotating
air seal from LPT shaft in one operation.
DESCRIPTION: The puller consists of a puller plate with hydraulic cylinder, a
pusher plate, attached to the hydraulic cylinder, and two puller ring halves, with
inner and outer lip, and a retainer ring. The inner lip interfaces with a groove
in the No. 6 bearing rotating air seal, the outer lip serves as a stop for the
retainer ring. The retainer ring retains the puller ring halves.
DIMENSIONS: 10 in. (254 mm) dia x 10 in. (254 mm) long.
WEIGHT: 42 lb (19 kg).
SUPPORTING TOOLS: Hydraulic hand pump and 0.375 in. connector.
TOOL MAINTENANCE: Coat treated surfaces (black oxide or black phosphate)
with corrosion preventive light oil when stored.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS LIST
GROUP PART NO. NOMENCLATURE QUANTITY SUPPLIER
NUMBER CODE
G01 2C14646P02 Pusher Plate 1
2C14646P03 Retainer Ring 1
2C14646P04 Puller Plate 1
2C14646P05 Puller Plate 1
2C14646P06 Collar 1
RC102 Hydraulic Cylinder 1 D
B2000-065 Belleville Washer 1 G
41109 Spherical Washer 1 F
AR-400 Coupler 1 D
FZ1616 Elbow 1 D
FOR ALL
2C14646G01
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C14646G01
Page 2
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
WRENCH, RETAINER NUT - NO. 6 BEARING OUTER RACE
2C14647G01
PURPOSE AND USE: To tighten or loosen the No. 6 bearing outer race.
DESCRIPTION: Consists of a countertorque plate, a guide, and a torque tube.
The guide is bolted to the turbine rear frame sump housing. The torque tube
is inserted through the guide. It incorporates four fingers which engage the
No. 6 bearing retainer nut and is splined on the opposite end for interfacing
with a torque multiplier. The countertorque plate bolts to the turbine rear
frame flange and guides the aft end of the torque tube. It also contains
provision for mounting the torque multiplier.
DIMENSIONS: 32 x 15 x 16 in. (812 x 381 x 406 mm).
WEIGHT: 60 lb (27 kg).
SUPPORTING TOOLS: Sweeney Torque Multiplier, Model 8100.
TOOL MAINTENANCE: Coat treated surfaces (black oxide or black phosphate)
with corrosion preventive light oil when stored.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS LIST
GROUP PART NO. NOMENCLATURE QUANTITY SUPPLIER
NUMBER CODE
G01 2C14647P02 Countertorque Plate 1
2C14647P03 Guide 1
2C14647P04 Torque Tube 1
2C14647P05 Hand Knob 2
2C14647P06 Pin 1
CL-10-KR Cable Ring 2 I
133091 Steel Chain Ring 2 ER
No. 8 Sash Chain 2 R
FOR ALL
2C14647G01
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C14647G01
Page 2
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
PULLER, NO. 1 BEARING AND AIR/OIL SEAL
2C14648G01
PURPOSE AND USE: To remove the No. 1 rotating bearing air/oil seal and
the inner races from the fan forward shaft.
DESCRIPTION: The puller consists of three puller tubes, a pusher
plate, and a puller plate.
DIMENSIONS: 48 x 24 x 15 in. (1220 x 610 x 380 mm).
WEIGHT: 5 lb (23 kg).
SUPPORTING TOOLS: Hydraulic hand pump and a 0.375 connector.
TOOL MAINTENANCE: Coat treated surfaces (black oxide or black phosphate)
with corrosion preventive light oil when stored.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS LIST
GROUP PART NO. NOMENCLATURE QUANTITY SUPPLIER
NUMBER CODE
G01 2C14648P02 Puller 1
2C14648P03 Sleeve 1
2C14648P04 Handle 2
2C14648P05 Puller 1
2C14648P06 Puller 1
2C14648P07 Sleeve 1
2C14648P08 Locator Ring 1
2C14648P09 Pusher Plate 1
2C14648P10 Pilot 1
2C14648P11 Puller Plate 1
2C14648P12 Plate 1
2C14648P13 Detent Pin 6
2C14648P23 Handle 2
2C14648P24 Ring 1
2C14648P25 Strip 1
RC252 Hydraulic Cylinder 1 D
12705-4C-8B Shoulder Bolt 6 U
BLDC4-03 Quick Release Pin 2 A
BLDC4-05 Quick Release Pin 2 A
133091 Chain Ring 4 ER
133091 Sash-Nickel Plated 4 R
Steel Chain
FOR ALL
2C14648G01
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C14648G01
Page 2
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FIXTURE, MOTORING - CORE ENGINE
2C14649P02
PURPOSE AND USE: The Motoring Fixture is used to rotate the high pressure
compressor (HPC) rotor to facilitate borescope engine inspection.
DESCRIPTION: The Motoring Fixture consists of a pneumatic drive motor with a right
angle drive. The P02 has a hand control, is a non-FADEC and was superseded by P04.
DIMENSIONS: 5 x 30 in. (127 x 762 mm).
WEIGHT: 6 lbs (3 kg).
SUPPORTING TOOLS: 90 psi (621 kPa) filtered and lubricated air supply.
TOOL MAINTENANCE: TBD
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing 2C14649.
FOR ALL
2C14649P02
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C14649P02
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FIXTURE, MOTORING - CORE ENGINE
2C14649P03
PURPOSE AND USE: The Motoring Fixture is used to rotate the high pressure
compressor (HPC) rotor to facilitate borescope engine inspection.
DESCRIPTION: The Motoring Fixture consists of a pneumatic drive motor with a right
angle drive. The P03 is foot-controlled, is a non-FADEC and was superseded by P05.
DIMENSIONS: 5 x 30 in. (127 x 762 mm).
WEIGHT: 6 lbs (3 kg).
SUPPORTING TOOLS: 90 psi (621 kPa) filtered and lubricated air supply.
TOOL MAINTENANCE: TBD
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing 2C14649.
FOR ALL
2C14649P03
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C14649P03
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FIXTURE, MOTORING - CORE ENGINE
2C14649P04
PURPOSE AND USE: The Motoring Fixture is used to rotate the high pressure
compressor (HPC) rotor to facilitate borescope engine inspection.
DESCRIPTION: The Motoring Fixture consists of a pneumatic drive motor with
a right angle drive. The P04 has a hand control.
DIMENSIONS: 5 x 30 in. (127 x 762 mm).
WEIGHT: 6 lbs (3 kg).
SUPPORTING TOOLS: 90 psi (621 kPa) filtered and lubricated air supply.
TOOL MAINTENANCE: TBD
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing 2C14649.
FOR ALL
2C14649P04
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C14649P04
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FIXTURE, MOTORING - CORE ENGINE
2C14649P05
PURPOSE AND USE: The Motoring Fixture is used to rotate the high pressure
compressor (HPC) rotor to facilitate borescope engine inspection.
DESCRIPTION: The Motoring Fixture consists of a pneumatic drive motor with
a right angle drive. The P05 is foot-controlled.
DIMENSIONS: 5 x 30 in. (127 x 762 mm).
WEIGHT: 6 lbs (3 kg).
SUPPORTING TOOLS: 90 psi (621 kPa) filtered and lubricated air supply.
TOOL MAINTENANCE: TBD
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing 2C14649.
FOR ALL
2C14649P05
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C14649P05
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
WRENCH, RETAINER NUT - INNER RACE, NO. 6 BEARING
2C14650G01
FOR ALL
2C14650G01
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C14650G01
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
WRENCH, RETAINER NUT - INNER RACE, NO. 6 BEARING
2C14650G02
FOR ALL
2C14650G02
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C14650G02
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
CHUCK TABLE COMPRESSOR ROTOR ASSEMBLY FIXTURE
2C14651G01
PURPOSE AND USE: To hold and turn the compressor rotor during runout check.
DESCRIPTION: The tool consists of a rota table, centering block, anti-rotation
device, and hydraulic chuck. It is part of buildup fixture, 2C14659.
DIMENSIONS: 38 x 22 in. (965 x 559).
WEIGHT: 950 lbs (431 kg).
SUPPORTING TOOLS: 2C14652 and 2C6629.
TOOL MAINTENANCE: Apply corrosion preventive oil and store with
cover to resist corrosion.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS LIST
GROUP PART NO. NOMENCLATURE QUANTITY SUPPLIER
NUMBER CODE
G01 2C14651P02 Rotary Table 1
2C14651P03 Centering Block 6
2C14651P04 Anti-Rotation Device 1
2C14651P05 Hydraulic Chuck 1
2C14651P06 Cover 1
FOR ALL
2C14651G01
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C14651G01
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
MASTER, SETUP - COMPRESSOR ROTOR BUILDUP
2C14652P01
PURPOSE AND USE: To set up and check runout of the hydraulic chuck
2C14651 when mounted on a rotary table.
DESCRIPTION: This is a multiple diameter precision set master to be
used with the hydraulic chuck 2C14651.
DIMENSIONS: 7.5 in. (191 mm) dia x 63 in. (1600 mm) long.
WEIGHT: TBD
SUPPORTING TOOLS: Used with hydraulic chuck 2C14651.
TOOL MAINTENANCE: TBD
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: None required.
FOR ALL
2C14652P01
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C14652P01
Page 2
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
BRACKET SET - TURBINE REAR FRAME TO SUB-ASSEMBLY STAND
2C14653G01
PURPOSE AND USE: The Bracket Set is used to attach the turbine rear frame to
the rotation mechanisms of the sub-assembly stand.
DESCRIPTION: The Bracket Set consists of two U-shaped items with twelve through
holes. The tool has a black oxide or black phosphate finish.
DIMENSIONS: 10 x 10 x 7 in. (254 x 254 x 178 mm).
WEIGHT: 6 lb (3 kg).
SUPPORTING TOOLS: 2C6217, 2C14277.
TOOL MAINTENANCE: Apply corrosion preventive oil to all surfaces that
have black oxide or black phosphate coating.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing 2C14653.
FOR ALL
2C14653G01
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C14653G01
Page 2
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FIXTURE, LIFT - LPT DISK, STAGE 5
2C14654G01
PURPOSE AND USE: To install/remove the stage 5 low pressure turbine disk
during build-up of the low pressure module.
DESCRIPTION: This fixture consists of an aluminum ring to which is
attached a three-legged sling by means of three hoist rings, and three
"U" shaped brackets to captivate the disk. The G01 version is used with
Pre SB 72-0984, stage 5 disk 9373M55.
DIMENSIONS: 22 in. (559 mm) dia x 0.75 in. (19.1 mm).
WEIGHT: 18 lbs (8 kg).
SUPPORTING TOOLS: Hoist.
TOOL MAINTENANCE: Coat treated surfaces (black oxide or black phosphate)
with corrosion preventive light oil when stored.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS LIST
GROUP PART NO. NOMENCLATURE QUANTITY SUPPLIER
NUMBER CODE
G01 2C14654P02 Support Ring 1
2C14654P03 Holding Block 3
2C14654P04 Insert 3
2C14654P05 Stud 3
2C14654P06 Sling Assembly 1
52325-4-11F Ball Lock Pin 3 A
125054 Chain Ring 6 ER
No. 8 Sash-Nickel Plated 3 P
Chain
FOR ALL
2C14654G01
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C14654G01
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FIXTURE, LIFT - LPT DISK, STAGE 5
2C14654G02
PURPOSE AND USE: To install/remove the stage 5 low pressure turbine disk
during build-up of the low pressure module.
DESCRIPTION: This fixture consists of an aluminum ring to which is attached a
three-legged sling by means of three hoist rings, and three "U" shaped brackets to
captivate the disk. The G02 version is used with SB 72-0984, stage 5 disk 1863M65.
DIMENSIONS: 22 in. dia x 0.75 in. (559 mm dia x 19.1 mm).
WEIGHT: 18 lbs (8 kg).
SUPPORTING TOOLS: Hoist.
TOOL MAINTENANCE: Coat treated surfaces (black oxide or black phosphate)
with corrosion preventive light oil when stored.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS LIST
GROUP PART NO. NOMENCLATURE QUANTITY SUPPLIER
NUMBER CODE
G02 2C14654P02 Support Ring 1
2C14654P05 Stud 3
2C14654P06 Sling Assembly 1
52325-4-11F Ball Lock Pin 3 A
125054 Chain Ring 6 ER
No. 8 Sash-Nickel Plated 3 P
Chain
2C14654P15 Holding Block 3
FOR ALL
2C14654G02
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C14654G02
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
DELETED
2C14655G01
PURPOSE AND USE: This tool has been deleted in its entirety.
Superseded by tool 2C14655G03.
FOR ALL
2C14655G01
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
WRENCH, TORX SCREW - LPT STATIONARY AIR SEAL
2C14655G03
FOR ALL
2C14655G03
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C14655G03
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
BRACKET SET - TURBINE REAR FRAME TO SUB-ASSEMBLY STAND
2C14656G02
PURPOSE AND USE: The Concentricity Gage is used to check the concentricity
of the seals relative to the No. 6 bearing I.D.
DESCRIPTION: The Concentricity Gage consists of an expansion arbor, one
dial indicator, and an actuation thumb screw. A container is provided. The
tool has a black oxide or black phosphate finish.
DIMENSIONS: 7 x 8 in. (178 x 203 mm).
WEIGHT: 4 lb (2 kg).
SUPPORTING TOOLS: None.
TOOL MAINTENANCE: Apply corrosion preventive oil to all surfaces that have
black oxide or black phosphate coating. Periodic inspection and calibration
are required. Refer to drawing 2C14656.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing 2C14656.
FOR ALL
2C14656G02
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C14656G02
Page 2
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FIXTURE, BUILDUP - COMPRESSOR ROTOR
2C14659G01
PURPOSE AND USE: The Buildup Fixture is used to support the compressor rotor aft
shaft and to take runout readings during compressor rotor assembly.
DESCRIPTION: The Buildup Fixture consists of chuck table fixture 2C14651,
indicator pylon 2C6629, four mounting bolts and washers. The tool has
a black oxide or black phosphate finish.
DIMENSIONS: 2C6629, 85 x 20 x 30 in. (2159 x 508 x 762 mm). 2C14651,
38 x 22 in. (965 x 559 mm).
WEIGHT: 1371 lbs (622 kg).
SUPPORTING TOOLS: 2C14651, 2C6629.
TOOL MAINTENANCE: Apply corrosion preventive oil to all surfaces that
have black oxide or black phosphate coating.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing 2C14659.
FOR ALL
2C14659G01
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C14659G01
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
TOOL, PREBEND AND SEAT - RETAINERS
2C14660G01
PURPOSE AND USE: The Prebend and Seat Tool is used to prebend and final seat
stage 1, 4, and 5 low pressure turbine (LPT) blade retainers. It is designed
for individual disks and is not to be used on an assembled rotor.
DESCRIPTION: The Prebend and Seat Tool consists of a pair of hydraulic
actuated pliers with interchangeable feet. The tool has a black
oxide or black phosphate finish.
DIMENSIONS: 20 x 10 x 4 in. (508 x 254 x 102 mm).
WEIGHT: 28 lb (13 kg).
SUPPORTING TOOLS: 6000 psi (41370 kPa) Hydraulic Pump.
TOOL MAINTENANCE: Apply corrosion preventive oil to all surfaces that
have black oxide or black phosphate coating.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing 2C14660.
FOR ALL
2C14660G01
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C14660G01
Page 2
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
TOOL, PREBEND AND SEAT - RETAINERS
2C14660G02
PURPOSE AND USE: The Prebend and Seat Tool is used to prebend and final seat
stage 1, 4, and 5 low pressure turbine (LPT) blade retainers. It is designed
for individual disks and is not to be used on an assembled rotor.
DESCRIPTION: The Prebend and Seat Tool consists of a pair of hydraulic
actuated pliers with interchangeable feet. The tool has a black
oxide or black phosphate finish.
DIMENSIONS: 20 x 10 x 4 in. (508 x 254 x 102 mm).
WEIGHT: 28 lb (13 kg).
SUPPORTING TOOLS: 6000 psi (41370 kPa) Hydraulic Pump.
TOOL MAINTENANCE: Apply corrosion preventive oil to all surfaces that
have black oxide or black phosphate coating.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing 2C14660.
FOR ALL
2C14660G02
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C14660G02
Page 2
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FIXTURE, INSTALLATION/REMOVAL COMPRESSOR REAR FRAME ASSEMBLY
2C14661G01
FOR ALL
2C14661G01
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
GROUP PART NO. NOMENCLATURE QUANTITY SUPPLIER
NUMBER CODE
2C14661P17 Pusher Tube 1
2C14661P18 Shaft 1
2C14661P19 Nut 1
2C14661P20 Guide Tube 1
2C14661P21 Drive Tube 1
2C14661P22 Container 1
2C14661P48 Tag 1
LC-08OL-5 Compression Spring 6 L
H64-16 Head Pressfit Bushing 6 CN
12705L-12C-608 Shoulder Screw 6 U
CL-4-BLP-L-1-5-S Ball-Lock Pin 1 I
12705-L-5C-248 Shoulder Screw 1 U
133091 Chain Ring 8 ER
8 Nickel Plated Chain 4 R
C810 with flat back Dial Indicator 1 AV
and 3.0 special stem
AD-87 Split Callet AV
ADB23006 Safety Hoist Ring 2 CN
CL-6-BLP-B-3.0-S Ball-Lock Pin 1 I
CL-6-BLP-L-1.5-S Ball-Lock Pin 2 I
ADB-23052 Safety Hoist Ring 2 CN
FOR ALL
2C14661G01
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C14661G01
Page 3
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FIXTURE, INSTALLATION/REMOVAL COMPRESSOR REAR FRAME ASSEMBLY
2C14661G02
FOR ALL
2C14661G02
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
GROUP PART NO. NOMENCLATURE QUANTITY SUPPLIER
NUMBER CODE
2C14661P18 Shaft 1
2C14661P19 Nut 1
2C14661P20 Guide Tube 1
2C14661P21 Drive Tube 1
2C14661P22 Container 1
2C14661P49 Tag 1
2C14661P50 Frame 1
2C14661P51 Safe Guard Sling 3
2C14661P52 Side Pull Hoist Ring 2
LC-08OL-5 Compression Spring 6 L
H64-16 Head Pressfit Bushing 6 CN
12705L-12C-608 Shoulder Screw 6 U
CL-4-BLP-L-1-5-S Ball-Lok Pin 1 I
12705-L-5C-248 Shoulder Screw 1 U
133091 Chain Ring 8 ER
8 Nickel Plated Chain 4 R
C810 with flat back Dial Indicator 1 AV
and 3.0 special stem
AD-87 Split Callet AV
CL-6-BLP-B-3.0-S Ball-Lok Pin 1 I
CL-6-BLP-L-1.5-S Ball-Lok Pin 2 I
ADB-23052 Safety Hoist Ring 2 CN
FOR ALL
2C14661G02
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C14661G02
Page 3
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FIXTURE, MACHINING AND INSPECTION - FAN BOOSTER STATOR CASES
2C14662G01
PURPOSE AND USE: The Machining and Inspection Fixture is used to hold
the fan booster stator assembly on a vertical turret lathe (VTL)
while the shrouds are machined.
DESCRIPTION: The Machining and Inspection Fixture consists primarily of a
circular mounting ring and a circular support ring with twelve clamps. The
tool has a black oxide or black phosphate finish.
DIMENSIONS: 50 x 6 in. (1270 x 152 mm).
WEIGHT: 750 lb (340 kg).
SUPPORTING TOOLS: Vertical Turret Lathe, 60 in. (1524 mm) capacity.
TOOL MAINTENANCE: Apply corrosion preventive oil to all surfaces that
have black oxide or black phosphate coating.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing 2C14662.
FOR ALL
2C14662G01
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C14662G01
Page 2
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
WRENCH SET, RETAINER NUT - NO. 5 INNER BEARING RACE
2C14664G01
PURPOSE AND USE: To install or remove the inner spanner nuts from the 5R bearing.
DESCRIPTION: The wrench set consists of: 1. A mounting plate for the torque
multiplier. 2. An anti-torque tube to react the multiplier torque on the
stage 1 HPT shaft inner splines. 3. A torque tube assembly that interfaces
with the spanner nut through the use of spring loaded quarter turn pins and
external splines to engage the torque multiplier.
DIMENSIONS: 9 x 18.5 in. (229 x 470 mm).
WEIGHT: 180 lbs (82 kg).
SUPPORTING TOOLS: Torque Multiplier, Sweeney Model No. 8100 or equivalent.
TOOL MAINTENANCE: Coat treated surfaces (black oxide or black phosphate)
with corrosion preventive light oil when stored.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS LIST
GROUP PART NO. NOMENCLATURE QUANTITY SUPPLIER
NUMBER CODE
G01 2C14664P02 Spanner Plate 1
2C14664P03 Anti-Torque Tube 1
2C14664P04 Ring 2
2C14664P05 Torque Tube 1
2C14664P06 Knurled Head Screw 2
2C14664P07 Plunger 8
2C14664P08 Knurled Knob 8
2C14664P09 Hand Knob 1
LC-026C-1 Compression Spring 8
CL-42-KA-12-12-L Cable Assembly 1
FOR ALL
2C14664G01
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C14664G01
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
WRENCH SET, RETAINER NUT - NO. 5 INNER BEARING RACE
2C14664G02
PURPOSE AND USE: To install or remove the inner spanner nuts from the 5R bearing.
DESCRIPTION: The wrench set consists of: 1. A mounting plate for the torque
multiplier. 2. An anti-torque tube to react the multiplier torque on the
stage 1 HPT shaft inner splines. 3. A torque tube assembly that interfaces
with the spanner nut through the use of spring loaded quarter turn pins and
external splines to engage the torque multiplier.
DIMENSIONS: 9 x 18.5 in. (229 x 470 mm).
WEIGHT: 180 lbs (82 kg).
SUPPORTING TOOLS: Torque Multiplier, Sweeney Model No. 8100 or equivalent.
TOOL MAINTENANCE: Coat treated surfaces (black oxide or black phosphate)
with corrosion preventive light oil when stored.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS LIST
GROUP PART NO. NOMENCLATURE QUANTITY SUPPLIER
NUMBER CODE
G02 2C14664P04 Ring 2
2C14664P06 Knurled Head Screw 2
2C14664P08 Knurled Knob 8
2C14664P09 Hand Knob 1
2C14664P15 Spanner Plate 1
2C14664P16 Anti-Torque Tube 1
2C14664P17 Torque Tube 1
2C14664P19 Plunger 8
LC-026C-1 Compression Spring 8
CL-42-KA-12-12-L Cable Assembly 1
FOR ALL
2C14664G02
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C14664G02
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
TOOL SET, INSTALLATION OR REMOVAL - NO. 4R BEARING OUTER RACE AND SPANNER NUT
2C14665G02
PURPOSE AND USE: The Installation or Removal Tool Set is used to install or remove
the No. 4R bearing outer race and 4R bearing outer race spanner nut.
DESCRIPTION: The Installation or Removal Tool Set consists primarily of a torque
tube, countertorque plate, a circular base with upper and lower plates and a
hydraulic cylinder. The tool has a black oxide or black phosphate finish.
DIMENSIONS: 24 x 24 x 16 in. (610 x 610 x 406 mm).
WEIGHT: 80 lbs (36 kg).
SUPPORTING TOOLS: Torque Multiplier, Sweeney Model No. 8100 or equivalent.
TOOL MAINTENANCE: Apply corrosion preventive oil to all surfaces that
have black oxide or black phosphate coating.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing 2C14665.
FOR ALL
2C14665G02
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C14665G02
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
PUSHER, INSTALLATION OR REMOVAL - NO. 4B BEARING OUTER RACE
2C14666G01
PURPOSE AND USE: To install or remove the No. 4B bearing outer race.
DESCRIPTION: The pusher consists of a base plate with posts attached to the aft
side. The posts support a circular cylinder plate which has a hydraulic cylinder
secured at the center in an inverted position. It also has two circular sectors
which are attached to the forward side 180 degrees apart. Each circular sector
can be moved radially outward or inward after disengaging a retainer ring. When
in the engaged position, the retainer ring keeps the tabs of the circular sectors
engaged in the gaps between the ribs of the No. 4B bearing housing. This keeps the
No. 4B bearing housing from moving axially upward while removing the outer race.
A circular pusher plate is attached to the piston of the hydraulic cylinder with a
bolt. The circular pusher plate is attached to the two rabbet diameters near its
outer perimeter. The forward end of the No. 4B bearing housing interfaces with the
largest rabbet diameter while installing the outer race. A pusher ring interfaces
with the other rabbet diameter during the removal of the outer race. During this
operation, the pusher ring is retained in position by studs and nuts. Each stud is
inserted through a hole in the pusher ring and the circular pusher plate; then it
is attached to the circular cylinder plate and held in place with loctite. A nut
is installed to the other end of each stud which captivates the pusher ring.
DIMENSIONS: 15 x 15 x 15 in. (380 x 380 x 380 mm).
WEIGHT: 40 lbs (18 kg).
SUPPORTING TOOLS: Hydraulic Hand Pump and 0.375 Connector.
TOOL MAINTENANCE: Coat treated surfaces (black oxide or black phosphate)
with corrosion preventive light oil when stored.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS LIST
GROUP PART NO. NOMENCLATURE QUANTITY SUPPLIER
NUMBER CODE
G01 2C14666P02 Plate 1
2C14666P03 Bar 4
2C14666P04 Puller Plate 1
2C14666P05 Pusher Plate 1
2C14666P06 Collar 1
2C14666P07 Knurled Nut 3
2C14666P08 Pusher Ring 1
2C14666P09 Retainer Ring 1
2C14666P10 Protector Plate 1
2C14666P11 Puller Ring 2
2C14666P12 Handle 2
2C14666P13 Threaded Rod 3
FOR ALL
2C14666G01
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
GROUP PART NO. NOMENCLATURE QUANTITY SUPPLIER
NUMBER CODE
RC53 Hydraulic Cylinder 1 D
41107 Spherical Washer 1 F
B1500-107 Belleville Washer 1 Y
12705L-4C-4B Shoulder Screw 4 U
12705L-4C-8B Shoulder Screw 4 U
SKA-1 Knurled Knob 2 C
FOR ALL
2C14666G01
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C14666G01
Page 3
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
DELETED
2C14667G01
PURPOSE AND USE: This tool has been deleted in its entirety.
Superseded by tool 2C14667G02.
FOR ALL
2C14667G01
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
PUSHER, NO. 4R AND 4B BEARING INNER RACES, ROTATING AIR OR OIL SEAL
2C14667G02
PURPOSE AND USE: To install the No. 4R rotating air or oil seal, the No. 4R
inner race, and the No. 4B forward and aft inner races.
DESCRIPTION: The pusher consists of a hydraulic cylinder which is attached to a
pusher. The pusher pilots on a guide which is threaded into the compressor rotor
spool shaft. A stud is threaded into and is welded to the center of the guide
which extends aft through the pusher tube and cylinder rod. Threaded on the aft
end of the center stud is a knurled nut which interfaces with the cylinder rod. An
adapter (ring) which interfaces with the forward end of the pusher tube is supplied
to install the rotating air or oil seal and the No. 4R inner race.
DIMENSIONS: 10 x 20 x 20 in. (254 x 508 x 508 mm).
WEIGHT: 70 lbs (32 kg).
SUPPORTING TOOLS: Hydraulic Hand Pump with 3/8 connector.
TOOL MAINTENANCE: Coat treated surfaces (black oxide or black phosphate)
with corrosion preventive light oil when stored.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS LIST
GROUP PART NO. NOMENCLATURE QUANTITY SUPPLIER
NUMBER CODE
G02 2C14667P04 Ring 1
2C14667P10 Pusher 1
2C14667P11 Guide 1
2C14667P12 Knurled Nut 1
RCH-123 Holl-O-Cylinder 1 D
AR-400 High Flow Coupler 1 D
FZ1616 Street Elbow 1 D
FOR ALL
2C14667G02
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C14667G02
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FIXTURE SET, INSTALLATION AND REMOVAL - LOW PRESSURE TURBINE NOZZLES STAGE 1
2C14668G01
PURPOSE AND USE: The Installation and Removal Fixture Set is used to hoist the stage
1 low pressure turbine (LPT) nozzle, inner air tubes (spoolies) and pressure balance
seal assembly; to either install or remove them from the LPT case as an assembly.
DESCRIPTION: The Installation and Removal Fixture Set consists of a base ring
with a rest ring, three hold down clamps, a lift ring, thirteen sliding clamps,
three sliding clamps, thirteen radial sliding wedges, and a three legged lift
sling is attached to the lift ring. The tool has a black oxide or black phosphate
finish. The G01 version of the tool, now obsolete for the CF6-80C2 engine,
has an increased capacity for use on the CF6-80E1 engine.
DIMENSIONS: 40 x 10 in. (1,016 x 254 mm).
WEIGHT: 70 lbs (32 kg).
SUPPORTING TOOLS: 2C14208.
TOOL MAINTENANCE: Apply corrosion preventive oil to all surfaces that
have black oxide or black phosphate coating.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing 2C14668.
FOR ALL
2C14668G01
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C14668G01
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FIXTURE SET, INSTALLATION AND REMOVAL - LOW PRESSURE TURBINE NOZZLES STAGE 1
2C14668G02
PURPOSE AND USE: The Installation and Removal Fixture Set is used to hoist the stage
1 low pressure turbine (LPT) nozzle, inner air tubes (spoolies) and pressure balance
seal assembly; to either install or remove them from the LPT case as an assembly.
DESCRIPTION: The Installation and Removal Fixture Set consists of a base ring with
a rest ring, three hold down clamps, a lift ring, thirteen sliding clamps, three
sliding clamps, thirteen radial sliding wedges, and a three legged lift sling is
attached to the lift ring. The tool has a black oxide or black phosphate finish.
DIMENSIONS: 40 x 10 in. (1016 x 254 mm).
WEIGHT: 70 lb (32 kg).
SUPPORTING TOOLS: 2C14208.
TOOL MAINTENANCE: Apply corrosion preventive oil to all surfaces that
have black oxide or black phosphate coating.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing 2C14668.
FOR ALL
2C14668G02
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C14668G02
Page 2
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
PULLER, NO. 4R BEARING INNER RACE, ROTATING AIR, OIL SEAL, AND NO. 4B BEARING
FORWARD RACE
2C14669G01
PURPOSE AND USE: The Puller is used to remove the No. 4R bearing inner
race, rotating air and oil seal in one operation, and remove the No. 4B
bearing forward inner race in another operation.
DESCRIPTION: The Puller consists of a hydraulic cylinder threaded into
a pusher plate with its piston attached to a plug. The tool has a
black oxide or black phosphate finish.
DIMENSIONS: 10 x 16 x 20 in. (254 x 406 x 508 mm).
WEIGHT: 70 lb (32 kg).
SUPPORTING TOOLS: Hydraulic Hand Pump, 3/8 in. Connector.
TOOL MAINTENANCE: Apply corrosion preventive oil to all surfaces that
have black oxide or black phosphate coating.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing 2C14669.
FOR ALL
2C14669G01
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C14669G01
Page 2
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
PULLER, NO. 4R BEARING INNER RACE, ROTATING AIR, OIL SEAL, AND NO. 4B BEARING
FORWARD RACE
2C14669G02
PURPOSE AND USE: The Puller is used to remove the No. 4R bearing inner
race, rotating air and oil seal in one operation, and remove the No. 4B
bearing forward inner race in another operation.
DESCRIPTION: The Puller consists of a hydraulic cylinder threaded into
a pusher plate with its piston attached to a plug. The tool has a
black oxide or black phosphate finish.
DIMENSIONS: 10 x 16 x 20 in. (254 x 406 x 508 mm).
WEIGHT: 70 lb (32 kg).
SUPPORTING TOOLS: Hydraulic Hand Pump, 3/8 in. Connector.
TOOL MAINTENANCE: Apply corrosion preventive oil to all surfaces that
have black oxide or black phosphate coating.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing 2C14669.
FOR ALL
2C14669G02
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C14669G02
Page 2
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
WRENCH, 4R BEARING INNER RACE RETAINER NUT
2C14670G01
PURPOSE AND USE: To install or remove the 4R bearing inner race retainer
nut during engine assembly or disassembly.
DESCRIPTION: This wrench consists of: 1. A mounting plate for the torque
multiplier. 2. An anti-torque tube to react the multiplier torque on the
compressor rotor spool shaft. 3. A torque tube assembly which interfaces with the
spanner nut through spring loaded quarter turn pins. The opposite end of the torque
tube assembly has external splines to interface with the torque multiplier.
DIMENSIONS: 13 x 13 x 20.5 in. (330 x 330 x 521 mm).
WEIGHT: 180 lbs (82 kg).
SUPPORTING TOOLS: Torque Multiplier, Sweeney Model No. 8100 or equivalent.
TOOL MAINTENANCE: Coat treated surfaces (black oxide or black phosphate)
with corrosion preventive light oil when stored.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS LIST
GROUP PART NO. NOMENCLATURE QUANTITY SUPPLIER
NUMBER CODE
G01 2C14670P02 Spline Tube 1
2C14670P03 Anti-Torque Tube 1
2C14670P04 Countertorque Plate 1
2C1467OP05 Lock Knob 8
2C14670P06 Lock Pin 8
2C14670P07 Knob 1
2C14670P08 Thumb Screw 2
MS16555-631 Dowel-SST Pin 8
LC-026C-3 Compression Spring 8 L
FOR ALL
2C14670G01
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C14670G01
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
WRENCH, 4R BEARING INNER RACE RETAINER NUT
2C14670G02
PURPOSE AND USE: To install or remove the 4R bearing inner race retainer
nut during engine assembly or disassembly.
DESCRIPTION: This wrench consists of: 1. A mounting plate for the torque
multiplier. 2. An anti-torque tube to react the multiplier torque on the
compressor rotor spool shaft. 3. A torque tube assembly which interfaces with the
spanner nut through spring loaded quarter turn pins. The opposite end of the torque
tube assembly has external splines to interface with the torque multiplier. This
tool incorporates eight lock knobs to prevent disengagement during use.
DIMENSIONS: 13 x 13 x 20.5 in. (330 x 330 x 521 mm).
WEIGHT: 180 lbs (82 kg).
SUPPORTING TOOLS: Torque Multiplier, Sweeney Model No. 8100 or equivalent.
TOOL MAINTENANCE: Coat treated surfaces (black oxide or black phosphate)
with corrosion preventive light oil when stored.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS LIST
GROUP PART NO. NOMENCLATURE QUANTITY SUPPLIER
NUMBER CODE
G02 2C14670P02 Spline Tube 1
2C14670P03 Anti-Torque Tube 1
2C14670P04 Countertorque Plate 1
2C14670P06 Lock Pin 8
2C14670P07 Knob 1
2C14670P08 Thumb Screw 2
2C14670P11 Lock Knob 8
MS16555-631 Dowel-SST Pin 8
LC-026C-3 Compression Spring 8 L
FOR ALL
2C14670G02
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C14670G02
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
WRENCH, 4R BEARING INNER RACE RETAINER NUT
2C14670G04
PURPOSE AND USE: To install or remove the 4R bearing inner race retainer
nut during engine assembly or disassembly.
DESCRIPTION: This wrench consists of: 1. A mounting plate for the torque
multiplier. 2. An anti-torque tube to react the multiplier torque on the
compressor rotor spool shaft. 3. A torque tube assembly which interfaces
with the spanner nut through spring loaded quarter turn pins. The opposite
end of the torque tube assembly has external splines to interface with
the torque multiplier. This tool has an optional anti-torque tube with
a higher torque capacity and it is optional.
DIMENSIONS: 13 x 13 x 20.5 in. (330 x 330 x 521 mm).
WEIGHT: 180 lbs (82 kg).
SUPPORTING TOOLS: Torque Multiplier, Sweeney Model No. 8100 or equivalent.
TOOL MAINTENANCE: Coat treated surfaces (black oxide or black phosphate)
with corrosion preventive light oil when stored.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS LIST
GROUP PART NO. NOMENCLATURE QUANTITY SUPPLIER
NUMBER CODE
G04 2C14670P08 Thumb Screw 2
2C14670P13 Spline Tube 1
2C14670P14 Anti-Torque Tube 1
2C1467OP15 Countertorque Plate 1
2C14670P16 Lock Pin 8
Commercial Hex Screw Cap HD-STL, 2
GR8
FOR ALL
2C14670G04
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C14670G04
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
WRENCH, INSTALLATION OR REMOVAL - NO. 4B BEARING RETAINER NUT
2C14671G02
FOR ALL
2C14671G02
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C14671G02
Page 2
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
DELETED
2C14672G02
PURPOSE AND USE: This tool has been deleted in its entirety.
Superseded by tool 2C14672G04.
FOR ALL
2C14672G02
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FIXTURE, LIFT - HIGH PRESSURE TURBINE ASSEMBLY FORWARD
2C14672G04
PURPOSE AND USE: The Lift Fixture is used to lift and turn the high
pressure turbine (HPT) rotor assembly at the forward end during assembly
or disassembly and balance operations.
DESCRIPTION: The Lift Fixture consists of a guide tube, an index plate, a
lift plate, a compression spring, and two cotter pins. The tool is made of
steel with a black oxide or black phosphate finish.
DIMENSIONS: 8 in. dia x 27 in. (203 mm dia x 686 mm).
WEIGHT: 16 lbs (7.3 kg).
SUPPORTING TOOLS: Overhead Hoist.
TOOL MAINTENANCE: Apply corrosion preventive oil to all surfaces that
have black oxide or black phosphate coating.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing 2C14672.
FOR ALL
2C14672G04
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C14672G04
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
TOOL SET - ACCESSORY, INLET AND TRANSFER GEARBOX
2C14673G03
PURPOSE AND USE: The Tool Set is used to disassemble and assemble the
accessory, inlet and transfer gearboxes.
DESCRIPTION: The Tool Set consists of various pushers, pusher tubes, split plates,
rings, pullers, etc. This tool is applicable to CF6-80C2 FADEC engine models only.
DIMENSIONS: 36 x 36 x 36 in. (914 x 914 x 914 mm).
WEIGHT: 180 lbs (82 kg).
SUPPORTING TOOLS: Arbor Press.
TOOL MAINTENANCE: Apply corrosion preventive oil to all surfaces that
have black oxide or black phosphate coating.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing 2C14673.
FOR FADEC
2C14673G03
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR FADEC
2C14673G03
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
TOOL SET - ACCESSORY, INLET AND TRANSFER GEARBOX
2C14673G04
PURPOSE AND USE: The Tool Set is used to disassemble and assemble the
accessory, inlet and transfer gearboxes.
DESCRIPTION: The Tool Set consists of various pushers, pusher tubes, split plates,
rings, pullers, etc. This tool is applicable to CF6-80C2 PMC models only.
DIMENSIONS: 36 x 36 x 36 in. (914 x 914 x 914 mm).
WEIGHT: 180 lbs (82 kg).
SUPPORTING TOOLS: Arbor Press.
TOOL MAINTENANCE: Apply corrosion preventive oil to all surfaces that
have black oxide or black phosphate coating.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing 2C14673.
FOR PMC
2C14673G04
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR PMC
2C14673G04
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
DELETED
2C14673G06
PURPOSE AND USE: This tool has been deleted in its entirety.
FOR ALL
2C14673G06
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
TOOL SET - ACCESSORY, INLET AND TRANSFER GEARBOX
2C14673G07
PURPOSE AND USE: The Tool Set is used to disassemble and assemble the
accessory, inlet and transfer gearboxes.
DESCRIPTION: The Tool Set consists of various pushers, pusher tubes, split plates,
rings, pullers, etc. This tool is applicable to CF6-80C2 B6FA engine models only.
DIMENSIONS: 36 x 36 x 36 in. (914 x 914 x 914 mm).
WEIGHT: 180 lbs (82 kg).
SUPPORTING TOOLS: Arbor Press.
TOOL MAINTENANCE: Apply corrosion preventive oil to all surfaces that
have black oxide or black phosphate coating.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing 2C14673.
FOR B6FA
2C14673G07
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR B6FA
2C14673G07
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
TOOL SET - ACCESSORY, INLET AND TRANSFER GEARBOX
2C14673G08
PURPOSE AND USE: The Tool Set is used to disassemble and assemble the
accessory, inlet and transfer gearboxes.
DESCRIPTION: The Tool Set consists of various pushers, pusher tubes, split plates,
rings, pullers, etc. This tool is applicable to CF6-80C2 FADEC engine models only.
DIMENSIONS: 36 x 36 x 36 in. (914 x 914 x 914 mm).
WEIGHT: 180 lbs (82 kg).
SUPPORTING TOOLS: Arbor Press.
TOOL MAINTENANCE: Apply corrosion preventive oil to all surfaces that
have black oxide or black phosphate coating.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing 2C14673.
FOR FADEC
2C14673G08
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR FADEC
2C14673G08
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
TOOL SET - ACCESSORY, INLET AND TRANSFER GEARBOX
2C14673G09
PURPOSE AND USE: The Tool Set is used to disassemble and assemble the
accessory, inlet and transfer gearboxes.
DESCRIPTION: The Tool Set consists of various pushers, pusher tubes, split plates,
rings, pullers, etc. This tool is applicable to CF6-80C2 FADEC engine models only.
DIMENSIONS: 36 x 36 x 36 in. (914 x 914 x 914 mm).
WEIGHT: 180 lbs (82 kg).
SUPPORTING TOOLS: Arbor Press.
TOOL MAINTENANCE: Apply corrosion preventive oil to all surfaces that
have black oxide or black phosphate coating.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing 2C14673.
FOR FADEC
2C14673G09
Page 1
Dec 01/2016
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR FADEC
2C14673G09
Page 2
Dec 01/2016
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
TOOL ASSEMBLY, INSTALLATION OR REMOVAL, BUMPER BEARING RETAINER - COMPRESSOR ROTOR
2C14674G02
PURPOSE AND USE: The Installation or Removal Tool Assembly is used to remove
or install the high pressure compressor rotor.
DESCRIPTION: The Installation or Removal Tool Assembly consists of a torque
tube, forty blades, a clamp tube, a mounting plate, and a hoist ring. The
tool has a black oxide or black phosphate finish.
DIMENSIONS: 24 x 22 x 12 in. (610 x 559 x 305 mm).
WEIGHT: 20 lb (9 kg).
SUPPORTING TOOLS: Torque Multiplier, Sweeney Model No. 8100 or 8112.
TOOL MAINTENANCE: Apply corrosion preventive oil to all surfaces that
have black oxide or black phosphate coating.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing 2C14674.
FOR ALL
2C14674G02
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C14674G02
Page 2
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
SUPPORT, SUMP HOUSING - COMPRESSOR REAR FRAME, AFT
2C14675G03
PURPOSE AND USE: The Sump Housing Support is used to support the aft end of the
sump housing after removing the No. 5R bearing housing.
DESCRIPTION: The Sump Housing Support consists of an aluminum ring,
socket head cap screws, washers, and nuts.
DIMENSIONS: 18.75 x 1.25 in. (476 x 32 mm).
WEIGHT: 10 lb (5 kg).
SUPPORTING TOOLS: 2C14073.
TOOL MAINTENANCE: TBD
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing 2C14675.
FOR ALL
2C14675G03
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C14675G03
Page 2
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FIXTURE, INSTALLATION AND REMOVAL - AIR TUBE, STAGE 1 LPT NOZZLE
2C14676G01
PURPOSE AND USE: To install and remove the cooling air tube (spoolies).
G01 to be used on outer spoolies.
DESCRIPTION: This tool consists of a slide hammer assembly, a removable chuck
(body) to hold the expansion feet, and a threaded expansion pin 16 in. in
length. The expansion pin runs through the center of the fixture. A knob at
the top turns the pin and causes it to move down relative to the slide hammer
and expansion chuck assembly. This action forces the expansion feet out to
grip the spoolie. There are two sets of three expansion feet; one set for
the inner spoolies and one set for the outer spoolies.
DIMENSIONS: 2.5 in. (63 mm) dia x 15 in. (381 mm).
WEIGHT: 7 lb (3 kg).
SUPPORTING TOOLS: None required.
TOOL MAINTENANCE: TBD
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS LIST
GROUP PART NO. NOMENCLATURE QUANTITY SUPPLIER
NUMBER CODE
G01 2C1476P02 Expansion Pin 1
2C1476P03 Foot 3
2C1476P04 Body 1
2C1476P05 Slide Hammer 1
2C1476P06 Handle 1
2-118 O-Ring 6 K
FOR ALL
2C14676G01
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C14676G01
Page 2
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FIXTURE, INSTALLATION AND REMOVAL - AIR TUBE, STAGE 1 LPT NOZZLE
2C14676G02
PURPOSE AND USE: To install and remove the cooling air tube (spoolies).
G02 to be used on inner spoolies.
DESCRIPTION: This tool consists of a slide hammer assembly, a removable chuck
(body) to hold the expansion feet, and a threaded expansion pin 16 in. in
length. The expansion pin runs through the center of the fixture. A knob at
the top turns the pin and causes it to move down relative to the slide hammer
and expansion chuck assembly. This action forces the expansion feet out to
grip the spoolie. There are two sets of three expansion feet; one set for
the inner spoolies and one set for the outer spoolies.
DIMENSIONS: 2.5 in. (63 mm) dia x 15 in. (381 mm).
WEIGHT: 7 lb (3 kg).
SUPPORTING TOOLS: None required.
TOOL MAINTENANCE: TBD
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS LIST
GROUP PART NO. NOMENCLATURE QUANTITY SUPPLIER
NUMBER CODE
G02 2C1476P02 Expansion Pin 1
2C1476P04 Body 1
2C1476P05 Slide Hammer 1
2C1476P06 Handle 1
2C1476P13 Foot 3
2-118 O-Ring 6 K
FOR ALL
2C14676G02
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C14676G02
Page 2
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
TOOL SET - STRAIGHTENING AND REMOVAL, BLADE RETAINERS, LOW PRESSURE TURBINE ROTOR
2C14678G02
PURPOSE AND USE: The Straightening and Removal Tool Set is used to straighten the
low pressure turbine (LPT) blade retainers during disassembly.
DESCRIPTION: The Straightening and Removal Tool Set consists primarily of a pair of
pliers, a pair of pivot arms, a set of anvils, a straightening bar, a nylon rod,
and a pair of steel drivers. The pliers and straightening bar have green plastisol
coating. The other parts have a black oxide or black phosphate coating.
DIMENSIONS: Container, 20 x 12 x 10 in. (508 x 305 x 254 mm).
WEIGHT: 20 lb (9 kg).
SUPPORTING TOOLS: Soft Mallet.
TOOL MAINTENANCE: Apply corrosion preventive oil to all surfaces that
have black oxide or black phosphate coating.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing 2C14678.
FOR ALL
2C14678G02
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C14678G02
Page 2
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
SLEEVE, RETAINING - NO. 4B BEARING STACK UP
2C14679P01
PURPOSE AND USE: To retain the No. 4B bearing inner race so the bearing can
support the thrust load of the compressor rotor when the core engine turned
from the vertical to the horizontal position and reverse.
DESCRIPTION: The sleeve consists of a steel tube 7 in. (178 mm) dia x 17
in. (432 mm) long. Three sets of four lightening holes are cross-drilled
through the tube. On the I.D., at approximately the center of the tube, is a
6.50-3 buttress thread. Four 0.500 diameter holes at the aft end are for the
use of a drift pin for a little mechanical advantage.
DIMENSIONS: 7 in. (178 mm) dia x 17 in. (432 mm) long.
WEIGHT: 17 lb (8 kg).
SUPPORTING TOOLS: None required.
TOOL MAINTENANCE: Coat treated surfaces (black oxide or black phosphate)
with corrosion preventive light oil when stored.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: None required.
FOR ALL
2C14679P01
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C14679P01
Page 2
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
PULLER, MANIFOLD - COMPRESSOR ROTOR
2C14680G01
PURPOSE AND USE: To remove the manifold from the I.D. of the compressor
rotor spool at shaft. The puller reacts between the forward face of
the spool and the manifold aft lip.
DESCRIPTION: This is a three legged puller, guided by a threaded rod, which is
centered in a circular plate (hub). The legs will expand by turning the hex
nut at the forward end of the rod counterclockwise. The cone is being drawn
forward, pushing the tripod against the compression spring. This clamping
action between the tripod and the cone wedges the expandable legs radially
outward. Once contact between the components is made, the cone, tripod, and
legs simultaneously are drawn axially forward along the threaded rod with the
legs at a preset diametrical dimension. Retraction of the expandable legs
is accomplished by turning the rod counterclockwise. This causes the stop
screw (socket shoulder screw) to bottom out in the aft side slot of the plate.
This allows the cone to move away axially from the tripod enough to radially
retract the legs below the inside radius of the manifold.
DIMENSIONS: 12 x 7 x 7 in. (305 x 178 x 178 mm).
WEIGHT: 10 lb (4.5 kg).
SUPPORTING TOOLS: Torque Wrench, Twenty Five Ft/Lb minimum.
TOOL MAINTENANCE: Coat treated surfaces (black oxide or black phosphate)
with corrosion preventive light oil when stored.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS LIST
GROUP PART NO. NOMENCLATURE QUANTITY SUPPLIER
NUMBER CODE
G01 2C14680P02 Hub 1
2C14680P03 Shim 1
2C14680P04 Finger 3
2C14680P05 Pad 3
2C14680P06 Expander 1
2C14680P07 Shaft 1
2C14680P08 Nut 1
2C14680P09 Clevis 1
2C14680P10 Container 1
4412 Socket Head Shoulder 1 M
Screw
No-2-151 O-Ring 1 K
C-1100-135-1500 Compression Spring 1 M
FOR ALL
2C14680G01
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C14680G01
Page 2
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
GAGE SET, CONCENTRICITY - COMPRESSOR REAR FRAME
2C14681G02
PURPOSE AND USE: The Concentricity Gage Set is used to do run out checks on the No.
4 and No. 5 bearing stationary seals and frame flanges during engine overhaul.
DESCRIPTION: The Concentricity Gage Set is used with concentricity arbor
2C14683P02, clamps, brackets, and dial indicators. A container is provided.
The primary color of the tool is blue.
DIMENSIONS: Container, 48 x 15 x 18 (1219 x 381 x 457 mm).
WEIGHT: 75 lb (34 kg).
SUPPORTING TOOLS: 2C14227.
TOOL MAINTENANCE: Apply corrosion preventive oil to all surfaces that
have black oxide or black phosphate coating.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing 2C14681.
FOR ALL
2C14681G02
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C14681G02
Page 2
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
CLOSURE SET, LEAK CHECK - LUBE SYSTEM AND SUMP, COMPRESSOR REAR FRAME
2C14682G03
PURPOSE AND USE: The Leak Check Closure Set is used to check for leaks
by pressurizing the forward and aft sump, and the lube, scavenge, and
vent systems of the compressor rear frame.
DESCRIPTION: The Leak Check Closure Set consists of the forward sump plate, seal
ring, housing retainer, aft sump plate, cap ring, caps, and a restraint fixture for
sealing the forward and aft ends of the sumps. Additional items are provided to
seal the compressor rear frame. The primary color of the tool is blue.
DIMENSIONS: 48 x 26 x 24 in. (1219 x 660 x 610 mm).
WEIGHT: 90 lb (41 kg).
SUPPORTING TOOLS: Regulated air.
TOOL MAINTENANCE: TBD
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing 2C14682.
FOR ALL
2C14682G03
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C14682G03
Page 2
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
CLOSURE SET, LEAK CHECK - LUBE SYSTEM AND SUMP, COMPRESSOR REAR FRAME
2C14682G04
PURPOSE AND USE: The Leak Check Closure Set is used to check for leaks
by pressurizing the forward and aft sump, and the lube, scavenge, and
vent systems of the compressor rear frame.
DESCRIPTION: The Leak Check Closure Set consists of the forward sump plate, seal
ring, housing retainer, aft sump plate, cap ring, caps, and a restraint fixture
for sealing the forward and aft ends of the sumps. Additional items are provided
to seal the compressor rear frame. The primary color of the tool is blue. The
G04 version of the tool has a new aft sump plate and retainer and is applicable
to the CF6-80E1 and LM6000 engines, in addition to the CF6-80C2.
DIMENSIONS: 48 x 26 x 24 in. (1,219 x 660 x 610 mm).
WEIGHT: 90 lbs (41 kg).
SUPPORTING TOOLS: Regulated air.
TOOL MAINTENANCE: TBD
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing 2C14682.
FOR ALL
2C14682G04
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C14682G04
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
TOOL SET, REMOVAL - HIGH PRESSURE COMPRESSOR STATOR VANE SPRINGS
2C14684G02
PURPOSE AND USE: The Removal Tool Set is used to remove small springs holding
the vanes radially inward in the stator case preceding the removal of the
high pressure compressor (HPC) stator vanes.
DESCRIPTION: The Removal Tool Set consists of two pairs of spreaders. Both
spreaders consist of a pry-bar, a special pin, a fixed bar, a shoulder screw, and
a dowel pin. The tool has a black oxide or black phosphate finish.
DIMENSIONS: 14 x 2 x 1.75 in. (356 x 51 x 44 mm).
WEIGHT: 6 lb (3 kg).
SUPPORTING TOOLS: None.
TOOL MAINTENANCE: Apply corrosion preventive oil to all surfaces that
have black oxide or black phosphate coating.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing 2C14684.
FOR ALL
2C14684G02
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C14684G02
Page 2
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
ADAPTER, ANTI-TORQUE - FAN STATOR TO FAN DISK
2C14685G01
PURPOSE AND USE: To prevent the fan stator from rotating due to input torque when
tightening the 20 nuts which attach the fan disk to the fan forward shaft.
DESCRIPTION: The adapter consists of a steel plate that bolts to the
fan case, an arm fabricated from steel pipe with a clevis on an end
and an angle on the opposite end.
DIMENSIONS: 50 x 5 x 3 in (1270 x 127 x 76 mm).
WEIGHT: 10 lb (5 kg).
SUPPORTING TOOLS: LPC Lift Adapter, 2C14686.
TOOL MAINTENANCE: Coat treated surfaces (black oxide or black phosphate)
with corrosion preventive light oil when stored.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS LIST
GROUP PART NO. NOMENCLATURE QUANTITY SUPPLIER
NUMBER CODE
G01 2C14685P02 Torque Arm 1
2C14685P03 Adapter Plate 1
CL-6-DEP-1.4-5 Ball-Lok Pin 1 I
133091 Chain Ring 2 ER
8 Sash-Nickel Plated 1 R
Chain
FOR ALL
2C14685G01
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C14685G01
Page 2
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
ADAPTER, LIFT - LOW PRESSURE COMPRESSOR
2C14686G05
PURPOSE AND USE: The Lift Adapter is used to support and maintain
alignment between the low pressure compressor rotor and the stator during
low pressure compressor operations.
DESCRIPTION: The Lift Adapter consists of a welded adapter assembly, eight
struts made from 2 in. (51 mm) square tubing, a clevis on either side to allow
interface with stand 2C14227, and an adapter at the 12 o'clock position for
lift fixture 2C6856. The primary color of the tool is blue.
DIMENSIONS: 53 x 19 in. (1346 x 483 mm).
WEIGHT: 300 lb (136 kg).
SUPPORTING TOOLS: Dolly, 2C6856, 2C14227.
TOOL MAINTENANCE: Apply a corrosion preventive compound to all unplated and
unpainted surfaces. Refer to MIL-C-16173, Grade 3.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing 2C14686.
FOR ALL
2C14686G05
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C14686G05
Page 2
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
PULLER SET - STAGE 1 HIGH PRESSURE TURBINE DISK, RACES AND SEALS
2C14688G04
PURPOSE AND USE: The Puller Set is used to remove the diffuser, rotating
air seal, No. 5R bearing inner race and the bearing heat shield from
the high pressure turbine (HPT) rotor disk.
DESCRIPTION: The Puller Set consists of a hydraulic cylinder, puller
plate (compression plate), and adapters. The tool has a black
oxide or black phosphate finish.
DIMENSIONS: Container, 9 in. dia x 23.5 in. (229 mm dia x 597 mm).
WEIGHT: 200 lbs (91 kg).
SUPPORTING TOOLS: A CE-compliant pump with a pressure gage with maximum
pressure of 689 bar (10,000 psi).
TOOL MAINTENANCE: Apply corrosion preventive oil to all surfaces that
have black oxide or black phosphate coating.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing 2C14688.
FOR ALL
2C14688G04
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C14688G04
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
PULLER SET - STAGE 1 HIGH PRESSURE TURBINE DISK, RACES AND SEALS
2C14688G05
PURPOSE AND USE: The Puller Set is used to remove the diffuser, rotating
air seal, No. 5R bearing inner race and the bearing heat shield from
the high pressure turbine (HPT) rotor disk.
DESCRIPTION: The Puller Set consists of a hydraulic cylinder, puller plate
(compression plate), and adapters. The tool has a black oxide or black phosphate
finish. The G05 version of this tool uses different pullers than the G04 version
for use on R88DT boltless 80CX and CF6-80E1 HPT rotors.
DIMENSIONS: Container, 9 in. dia x 23.5 in. (229 mm dia x 597 mm).
WEIGHT: 200 lbs (91 kg).
SUPPORTING TOOLS: A CE-compliant pump with a pressure gage with a maximum
pressure of 689 bar (10,000 psi).
TOOL MAINTENANCE: Apply corrosion preventive oil to all surfaces that
have black oxide or black phosphate coating.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing 2C14688.
FOR ALL
2C14688G05
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C14688G05
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
ADAPTER LIFT - COMBUSTOR
2C14689G01
FOR ALL
2C14689G01
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C14689G01
Page 2
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FIXTURE, INSTALL/REMOVE - COMBUSTOR
2C14691G01
PURPOSE AND USE: To pull the combustor from the compressor rear frame
during disassembly, providing force to overcome the pressure fit between
the outer liner and the frame.
DESCRIPTION: Consists of a steel ring, eight socket head cap screws, nine
clamps, eight push pins, and three guides.
DIMENSIONS: 4 in. x 38 in. dia (102 mm x 965 mm dia).
WEIGHT: 85 lb (39 kg).
SUPPORTING TOOLS: Lift fixture, 4012388-609 hand wrenches.
TOOL MAINTENANCE: Coat black oxided surfaces with corrosion preventive oil.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS LIST
GROUP PART NO. NOMENCLATURE QUANTITY SUPPLIER
NUMBER CODE
G01 2C14691P02 Ring 1
2C14691P03 Pin 8
2C14691P04 Screw 8
2C14691P05 Clamp 9
2C14691P06 Knob 9
2C14691P07 Shim AR
2C14691P08 Guide 3
FOR ALL
2C14691G01
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C14691G01
Page 2
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FIXTURE, SEATING — LOW PRESSURE TURBINE NOZZLES STAGES 2 AND 3
2C14692G01
PURPOSE AND USE: To overcome the interference fit between the Low
Pressure Turbine Nozzles and shrouds.
DESCRIPTION: Consists of an aluminum ring with three open center hydraulic
cylinders attached to it. Three threaded rods project thru the cylinders.
A set of thickness gages is also provided. The fixture also includes
a pressure gage and a relief valve.
DIMENSIONS: 54 in. outer dia x 20 in. (1,372 mm outer dia x 508 mm).
WEIGHT: 300 lbs (136 kg).
SUPPORTING TOOLS: This tool is used with 2C14208 hydraulic pump.
TOOL MAINTENANCE: Apply corrosion preventive oil to all surfaces
that have black oxide finish.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing 2C14692.
FOR ALL
2C14692G01
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C14692G01
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
TOOL SET, INSTALLATION OR REMOVAL LPT MODULE TO OR FROM CORE MODULE
2C14693G01
PURPOSE AND USE: To prevent damage to the LPT rotating seals during installation
or removal of the LPT module. A container is provided.
DESCRIPTION: This tool set consists of four guides, 12 clamps, and 12 knurled
nuts. These guides keep the forward flanges concentric and limit the motion
in the axial direction to prevent damage to the seals.
DIMENSIONS: 9 x 4 x 3 in. (230 x 102 x 77 mm).
WEIGHT: 20 lb (9 kg).
SUPPORTING TOOLS: None required.
TOOL MAINTENANCE: Coat treated surfaces (black oxide or black phosphate)
with corrosion preventive light oil when stored.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS LIST
GROUP PART NO. NOMENCLATURE QUANTITY SUPPLIER
NUMBER CODE
G01 2C14693P02 Guide 4
2C14693P03 Clamp 12
2C14693P04 Pin 12
2C14693P05 Container 1
CL-l-KN Knurled Nut 12 I
FOR ALL
2C14693G01
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C14693G01
Page 2
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
PULLER, HEAT SHIELD - NO. 4R BEARING
2C14694G01
PURPOSE AND USE: To remove the 4R heat shield from the 4R stationary airoil
seal while it is attached to the compressor rear frame.
DESCRIPTION: The puller consists of a plate to which a hydraulic cylinder
is mounted. Two puller halves clamp around the outside diameter of the
plate and the lip of the heat shield. A puller ring is attached to the
hydraulic cylinder piston. This puller ring has a coated rabbet diameter
to prevent damaging the stationary seal.
DIMENSIONS: 12 in. dia x 8 in. (305 mm dia x 203 mm).
WEIGHT: 12 lbs (5.5 kg).
SUPPORTING TOOLS: Hydraulic hand pump and 3/8 connector.
TOOL MAINTENANCE: Coat treated surfaces (black oxide or black phosphate)
with corrosion preventive light oil when stored.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS LIST
GROUP PART NO. NOMENCLATURE QUANTITY SUPPLIER
NUMBER CODE
G01 2C14694P02 Plate 1
2C14694P03 Guide 1
2C14694P04 Puller Ring 1
2C14694P05 Swing Bolt 1
RC51 Hydraulic Cylinder 1 D
AR-400 Coupler 1 D
41107 Spherical Washer 1 F
27902 Knurled Knob 1 F
B1500-060 Belleville Washer 1 G
FOR ALL
2C14694G01
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C14694G01
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FIXTURE, LIFT - STAGE 1 HPT NOZZLE ASSEMBLY
2C14695G01
PURPOSE AND USE: To install or remove from the engine the stage 1 nozzle
assembly without disturbing the seals between the nozzles.
DESCRIPTION: This fixture consists of an aluminum ring that engages the
nozzle support on the I.D. Rubber foam is cemented to the O.D. face
of the ring to prevent seal disengagement.
DIMENSIONS: 36 x 34 x 10 in. (915 x 864 x 254 mm).
WEIGHT: 40 lbs (22 kg).
SUPPORTING TOOLS: Lift Adapter, 2C14219, Stage 1 HPT Nozzle
Assembly Fixture 2C14696.
TOOL MAINTENANCE: Coat treated surfaces (black oxide or black phosphate) with
corrosion preventive light oil when stored. Load test periodically (see GE
drawing 2C14695 for load test diagram and applicable NOTE).
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS LIST
GROUP PART NO. NOMENCLATURE QUANTITY SUPPLIER
NUMBER CODE
G01 2C14695P02 Arm 1
2C14695P03 Plate 1
CL-1420-KS Threaded Insert 4 I
CL-51618KS Threaded Insert 3 I
ADB-23051 Hoist Ring 3 Z
ADB-23004 Hoist Ring 1 Z
FOR ALL
2C14695G01
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C14695G01
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FIXTURE, ASSEMBLY - STAGE 1 HIGH PRESSURE TURBINE NOZZLE
2C14696G02
PURPOSE AND USE: The Assembly Fixture is used to install the stage 1 high
pressure turbine (HPT) nozzles to the nozzle support.
DESCRIPTION: The Assembly Fixture consists of a top and bottom plate supported
by four supports (spacers). Also provided are 23 knurled handles. The
tool has a black oxide or black phosphate finish.
DIMENSIONS: 42 x 6 in. (1067 x 152 mm).
WEIGHT: 75 lb (34 kg).
SUPPORTING TOOLS: 2C14695.
TOOL MAINTENANCE: Apply corrosion preventive oil to all surfaces that
have black oxide or black phosphate coating.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing 2C14696.
FOR ALL
2C14696G02
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C14696G02
Page 2
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
TOOL SET, RIGGING - BY-PASS VALVE
2C14697G03
PURPOSE AND USE: The Rigging Tool Set is used to hold the unison
ring circumferentially in a set position, during rigging of the
by-pass valve and linkages.
DESCRIPTION: The Rigging Tool Set consists of a circumferential locator,
a gage, and a ball-lok pin. A container is also provided. The tool has
a black oxide or black phosphate finish.
DIMENSIONS: 9 x 3 x 4 in. (229 x 76 x 102 mm).
WEIGHT: 15 lb (7 kg).
SUPPORTING TOOLS: None.
TOOL MAINTENANCE: Do an inspection and check the calibration of the tool
periodically. Refer to drawing 2C14697. Apply corrosion preventive oil to all
surfaces that have black oxide or black phosphate coating.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing 2C14697.
FOR ALL
2C14697G03
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C14697G03
Page 2
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
PULLER, NO. 2 ROLLER BEARING
2C14698G01
PURPOSE AND USE: To pull the No. 2 bearing from the No. 1 bearing housing
due to the interference fit between the two components.
DESCRIPTION: This puller consists of a support housing. This housing assembly
interfaces with the bearing housing through three dowel pins. A hydraulic
cylinder is mounted to a puller plate. Three puller feet apply force until
the bearing has been freed from the housing.
DIMENSIONS: 9 in. (230 mm) dia x 6 in. (153 mm) long.
WEIGHT: 20 lb (9 kg).
SUPPORTING TOOLS: None required.
TOOL MAINTENANCE: Coat treated surfaces (black oxide or black phosphate)
with corrosion preventive light oil when stored.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS LIST
GROUP PART NO. NOMENCLATURE QUANTITY SUPPLIER
NUMBER CODE
G01 2C14698P02 Support 1
2C14698P03 Puller Plate 1
2C14698P04 Puller Shaft 3
2C14698P05 Collar 3
2C14698P06 Puller Foot 3
2C14698P07 Stud 1
2C14698P08 Nut 1
SPW-6 Spherical Washer 1 C
X6-N Ball Plunger 3 C
B1500-045 Belleville Spring 1 G
Washer
5100-75 Retaining Ring 3 J
RC53 Hydraulic Cylinder 1 D
FZ1616 Street Elbow 1 D
FOR ALL
2C14698G01
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C14698G01
Page 2
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FIXTURE, LIFT - COMPRESSOR STATOR CASE, UPPER
2C14699G02
PURPOSE AND USE: The Lift Fixture is used to remove the upper
compressor stator case.
DESCRIPTION: The Lift Fixture consists of a telescoping bar with triangular plates
welded on each end. Pins are pressed into the triangular plates to interface with
the compressor stator case flanges. The primary color of the tool is blue.
DIMENSIONS: 46 x 12 x 9 in. (1168 x 305 x 229 mm).
WEIGHT: 45 lb (20 kg).
SUPPORTING TOOLS: Hoist.
TOOL MAINTENANCE: Apply corrosion preventive oil to all surfaces that have black
oxide or black phosphate coating. Coat all unplated and unpainted surfaces with
corrosion preventive compound. Refer to MIL-C-16173, Grade 3.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing 2C14699.
FOR ALL
2C14699G02
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C14699G02
Page 2
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
PULLER, NO. 6 BEARING OUTER RACE
2C14700G01
PURPOSE AND USE: To pull the No. 6 bearing puller from the bearing housing
due to interference fit between the two engine components.
DESCRIPTION: This puller consists of a tube, which interfaces with the
bearing housing. Three foot assemblies and a pilot plate interface the
forward and aft face of the bearing respectively. Hydraulic force is used to
separate the bearing from the housing. This tool is replaced by 2C14883G01,
due to unavailability of hydraulic cylinder.
DIMENSIONS: 10 in. (254 mm) dia x 10 in. (254 mm) long.
WEIGHT: 20 lbs (9 kg).
SUPPORTING TOOLS: None required.
TOOL MAINTENANCE: Coat treated surfaces (black oxide or black phosphate)
with corrosion preventive light oil when stored.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS LIST
GROUP PART NO. NOMENCLATURE QUANTITY SUPPLIER
NUMBER CODE
G01 2C14700P02 Pilot Plate 1
2C14700P03 Tube 1
2C14700P04 Cylinder Plate 1
2C14700P05 Foot 3
2C14700P06 Cylinder Nut 1
2C14700P07 Hand Knob 3
2C14700P08 Lift Handle 1
2C14700P09 Nut 3
RWP-101 Hydraulic Cylinder 1 D
1/4 FF-S Pipe Nipple 1 V
1/4 DD-S Female Pipe Elbow 1 V
1/4 FFF-3.5-S Long Pipe Nipple 1 V
3/8 x 1/4 GG-S Pipe Connector 1 V
AR-400 Coupler 1 D
FOR ALL
2C14700G01
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C14700G01
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FIXTURE, ASSEMBLY - STAGE 1 BOOSTER VANES
2C14701G02
PURPOSE AND USE: The Assembly Fixture is used to facilitate the alignment
of the stage 1 components during assembly.
DESCRIPTION: The Assembly Fixture consists of a base plate, ring (gage block), and
three lift eyes. The base plate has rings attached to position and hold down the
vanes. The tool has a nickel plate and black oxide or black phosphate finish.
DIMENSIONS: 57 x 4 in. (1448 x 102 mm).
WEIGHT: 588 lb (267 kg).
SUPPORTING TOOLS: 9383M90, 9392M99, 9392M81.
TOOL MAINTENANCE: Apply corrosion preventive oil to all surfaces that
have black oxide or black phosphate coating.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing 2C14701.
FOR ALL
2C14701G02
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C14701G02
Page 2
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FIXTURE, ASSEMBLY - HPT NOZZLE, STAGE 2
2C14702G01
FOR ALL
2C14702G01
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C14702G01
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
ADAPTER, LIFT - STAGE 2 HPT NOZZLE
2C14703G01
PURPOSE AND USE: To install or remove the stage 2 HPT nozzle assembly horizontally
or vertically while the fan mid shaft is being installed.
DESCRIPTION: This adapter consists of a welded spider assembly that has three legs
equally spaced, attached to the outside diameter of the pipe. Through holes in
the angle are provided to attach it to the HPT stator support aft flange. Each
upper gusset has a through hole for attaching a sling. A tube is attached at
the top vertical centerline to interface with lift adapter 2C14219.
DIMENSIONS: 38 in. dia x 6 in. (965 mm dia x 152 mm).
WEIGHT: 21 lbs (10 kg).
SUPPORTING TOOLS: Lift Adapter 2C14219 and three-legged sling.
TOOL MAINTENANCE: Coat treated surfaces (black oxide or black phosphate) with
corrosion preventive light oil when stored. Load test periodically (see GE
drawing 2C14703 for load test diagram and applicable NOTE).
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS LIST
GROUP PART NO. NOMENCLATURE QUANTITY SUPPLIER
NUMBER CODE
G01 2C14703P02 Spider 1
MS51971-1 Hex Nut, Steel 3
MS16995-54 Socket Head Cap Screw, 3
Steel
FOR ALL
2C14703G01
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C14703G01
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
TOOL SET, DUMMY SHAFT - COMPRESSOR OR HIGH PRESSURE TURBINE ROTOR
2C14704G06
PURPOSE AND USE: The Dummy Shaft Tool Set is used to do run-out checks on the
high pressure turbine (HPT) rotor or the compressor rotor.
DESCRIPTION: The Simulated Shaft Tool Set consists of a high pressure
compressor aft shaft, two coupling nuts, an HPT forward shaft, a stage 2
HPCR shaft, and a No. 4B bearing race. The tool has a silver plate, nickel
plate, and black oxide or black phosphate finish.
DIMENSIONS: 170 x 20 in. (4318 x 508 mm).
WEIGHT: 280 lb (127 kg).
SUPPORTING TOOLS: None.
TOOL MAINTENANCE: Do an inspection and check the calibration of the tool
periodically. Refer to drawing 2C14704. Apply corrosion preventive oil to all
surfaces that have black oxide or black phosphate coating.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing 2C14704.
FOR ALL
2C14704G06
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C14704G06
Page 2
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
CLOSURE, PRESSURE CHECK - FUEL DRAIN MANIFOLD
2C14711G01
PURPOSE AND USE: To check for leaks by pressurizing the fuel drain manifold.
DESCRIPTION: This closure set consists of a hose with two swage fittings,
one secured to each end. An elbow swivel nut secures the closure to
the drain manifold. A relief valve, gage, and connector is attached
to a cross at the aft end of the closure.
DIMENSIONS: 14 x 12 x 6 in. (356 x 305 x 153 mm).
WEIGHT: 6 lbs (3 kg).
SUPPORTING TOOLS: Nitrogen cart or equivalent.
TOOL MAINTENANCE: TBD
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS LIST
GROUP PART NO. NOMENCLATURE QUANTITY SUPPLIER
NUMBER CODE
G01 2C14711P02 Container 1
6-CX6-SS 90° Elbow Swivel Nut 1 V
1/4 KMM00-SS Female Pipe Cross 1 V
D559T-2M-60 Relief Valve 1 DD
2.50 Type 1009A 0.250 Gage 1 EF
NPT Lower Stem 0-100
PSI
5-4FTX-SS Connector 1 V
10191-4-6C Swage Fitting 1 CS
919-6 (2 ft long) Hose 1 CS
20690-6-6C Swage Fitting 1 CS
FOR ALL
2C14711G01
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C14711G01
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FIXTURE, POSITIONING - HORIZONTAL DRIVE SHAFT HOUSING
2C14712G01
PURPOSE AND USE: To engage or disengage the horizontal drive shaft housing
to or from the transfer or accessory gearbox.
DESCRIPTION: The fixture consists of a rectangular block. A ball-lok pin attaches
through both sides of the block and the boss of the horizontal drive shaft at
the mid point. A knurled handle attaches to bottom of the block. A mallet
is used to strike the end of the block to engage the housing. To disengage
the housing, use the mallet to strike the opposite end.
DIMENSIONS: 9 x 4 x 3 in. (230 x 112 x 76 mm).
WEIGHT: 2 lbs (0.9 kg).
SUPPORTING TOOLS: Mallet.
TOOL MAINTENANCE: Coat treated surfaces (black oxide or black phosphate)
with corrosion preventive light oil when stored.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS LIST
GROUP PART NO. NOMENCLATURE QUANTITY SUPPLIER
NUMBER CODE
G01 2C14712P02 Handle 1
2C14712P03 Pusher 1
BLC5BC22S Ball-Lock Pin 1 A
133091 Chain Ring 2 ER
N08 Sash-Nickel Plated 1 R
Chain
FOR ALL
2C14712G01
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C14712G01
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FIXTURE, RESTRAINING, STAGE 2 HIGH PRESSURE TURBINE NOZZLE ASSEMBLY
2C14714G02
PURPOSE AND USE: The Restraining Fixture is used to restrain the stage
2 high pressure turbine (HPT) nozzle support and nozzle assembly while
the bolts are being tightened.
DESCRIPTION: The Restraining Fixture consists of two plates (top and bottom), a
restraint ring, and a dial indicator support arm. Three lift eyes are provided in
the top plate to attach a three leg sling. Twenty-four radial clamps are attached
to the restraint ring. The tool has a black oxide or black phosphate finish.
DIMENSIONS: 42 x 6 in. (1067 x 152 mm).
WEIGHT: 250 lb (113 kg).
SUPPORTING TOOLS: None.
TOOL MAINTENANCE: Do an inspection and check the calibration of the tool
periodically. Refer to drawing 2C14714. Apply corrosion preventive oil to all
surfaces that have black oxide or black phosphate coating.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing 2C14714.
FOR ALL
2C14714G02
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C14714G02
Page 2
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FIXTURE, LIFT AND TURN - ENGINE, FORWARD
2C14715G01
PURPOSE AND USE: The Lift and Turn Fixture is used to lift and turn the forward
end of an engine from a vertical to horizontal position.
DESCRIPTION: The Lift and Turn Fixture consists of a base and an arm. The primary
color of the tool is blue. This tool is applicable to CF6-80C2 Airbus engines only.
DIMENSIONS: 36 x 8 x 3 in. (914 x 203 x 76 mm).
WEIGHT: 50 lbs (23 kg).
SUPPORTING TOOLS: Hoist, with a minimum capacity of 10,000 lbs (4,536 kg),
2C6211. Also uses Lift Adapter, 2C14795.
TOOL MAINTENANCE: Apply corrosion preventive oil to all surfaces that have black
oxide or black phosphate coating. Apply corrosion preventive compound to all
unplated and unpainted surfaces. Refer to MIL-C-16173, Grade 3.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing 2C14715.
FOR AIRBUS
2C14715G01
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR AIRBUS
2C14715G01
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FIXTURE, LIFT AND TURN - ENGINE, FORWARD
2C14715G02
PURPOSE AND USE: The Lift and Turn Fixture is used to lift and turn the forward
end of an engine from a vertical to horizontal position.
DESCRIPTION: The Lift and Turn Fixture consists of a base and an arm. The primary
color of the tool is blue. This tool is applicable to CF6-80C2 Boeing engines only.
DIMENSIONS: 36 x 8 x 3 in. (914 x 203 x 76 mm).
WEIGHT: 50 lbs (23 kg).
SUPPORTING TOOLS: Hoist, with a minimum capacity of 10,000 lbs (4,536 kg),
2C6211. Also uses Lift Adapter, 2C14795.
TOOL MAINTENANCE: Apply corrosion preventive oil to all surfaces that have black
oxide or black phosphate coating. Apply corrosion preventive compound to all
unplated and unpainted surfaces. Refer to MIL-C-16173, Grade 3.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing 2C14715.
FOR BOEING
2C14715G02
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR BOEING
2C14715G02
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FIXTURE, LIFT AND TURN - ENGINE, FORWARD
2C14715G03
PURPOSE AND USE: The Lift and Turn Fixture is used to lift and turn the forward
end of an engine from a vertical to horizontal position.
DESCRIPTION: The Lift and Turn Fixture consists of a base and an arm.
The primary color of the tool is blue. This tool is applicable to
CF6-80C2 Douglas engines only.
DIMENSIONS: 36 x 8 x 3 in. (914 x 203 x 76 mm).
WEIGHT: 50 lbs (23 kg).
SUPPORTING TOOLS: Hoist, with a minimum capacity of 10,000 lbs (4,536 kg),
2C6211. Also uses Lift Adapter, 2C14795.
TOOL MAINTENANCE: Apply corrosion preventive oil to all surfaces that have black
oxide or black phosphate coating. Apply corrosion preventive compound to all
unplated and unpainted surfaces. Refer to MIL-C-16173, Grade 3.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing 2C14715.
FOR DOUGLAS
2C14715G03
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR DOUGLAS
2C14715G03
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
ADAPTER SET, PEDESTAL - FAN STATOR
2C14717G01
PURPOSE AND USE: To support the engine at the forward fan case during
storage or maintenance operations.
DESCRIPTION: This adapter set consists of two brackets that
mount to the fan forward case.
DIMENSIONS: 30 x 8 in. (762 x 203 mm).
WEIGHT: 15 lb (7 kg).
SUPPORTING TOOLS: Engine Handling Support, 2C6339.
TOOL MAINTENANCE: Coat treated surfaces (black oxide or black phosphate)
with corrosion preventive light oil when stored.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS LIST
GROUP PART NO. NOMENCLATURE QUANTITY SUPPLIER
NUMBER CODE
G01 2C14717P02 Bracket 1
2C14717P03 Bracket 1
MS35308-362 Screw 6
MS51922-22 Nut 6
FOR ALL
2C14717G01
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C14717G01
Page 2
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FIXTURE, INSTALLATION AND REMOVAL - AIR TUBE HIGH PRESSURE TURBINE STAGE 2 NOZZLE
2C14718G02
PURPOSE AND USE: The Installation and Removal Fixture is used to install and remove
the cooling air tubes (spoolies) during buildup of the stage 2 nozzle assembly.
DESCRIPTION: The Installation and Removal Fixture consists of a slide
hammer, removable body and collar, expansion feet, and an expansion
pin. The tool is nickel plated.
DIMENSIONS: 2.5 x 15 in. (64 x 381 mm).
WEIGHT: 5.5 lb (2 kg).
SUPPORTING TOOLS: None.
TOOL MAINTENANCE: TBD
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing 2C14718.
FOR ALL
2C14718G02
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C14718G02
Page 2
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FIXTURE RUNOUT - FAN STATOR, ASSEMBLED ENGINE
2C14722G01
FOR ALL
2C14722G01
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C14722G01
Page 2
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FIXTURE, LIFT - INLET GEARBOX
2C14725G01
PURPOSE AND USE: To remove and install the inlet gearbox in the fan frame
when the fan frame is in the horizontal position.
DESCRIPTION: This fixture consists of a "C" shaped welded assembly fabricated
from rectangular steel tubing. This structure is equipped with two pilots made
from phenolic material that interface with the inside diameter of the horizontal
gearshaft. Two draw bars at the same end prevent disengagement of the gearbox
from the fixture. A "U" bolt is attached to the opposite end for an overhead
lifting system. This tool has a capacity of 90 lbs (40.8 kg).
DIMENSIONS: 57 x 58 in. (1,448 x 1,473 mm).
WEIGHT: 60 lbs (28 kg).
SUPPORTING TOOLS: None required.
TOOL MAINTENANCE: Coat treated surfaces (black oxide or black phosphate) with
corrosion preventive light oil when stored. Load test periodically (see GE
drawing 2C14725 for load test diagram and applicable NOTE).
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS LIST
GROUP PART NO. NOMENCLATURE QUANTITY SUPPLIER
NUMBER CODE
G01 2C14725P02 Lift Arm 1
2C14725P03 U Bolt 1
2C14725P04 Draw Bar 2
2C14725P05 Check Nut 2
2C14725P06 Knurled Knob 2
FOR ALL
2C14725G01
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C14725G01
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FIXTURE, LIFT - INLET GEARBOX
2C14725G02
PURPOSE AND USE: To remove and install the inlet gearbox in the fan
frame when is in the horizontal position.
DESCRIPTION: This fixture consists of a "C" shaped welded assembly fabricated
from rectangular steel tubing. This structure is equipped with two pilots made
from phenolic material that interface with the inside diameter of the horizontal
gearshaft. Two draw bars at the same end prevent disengagement of the gearbox
from the fixture. A "U" bolt is attached to the opposite end for an overhead
lifting system. This tool has a capacity of 120 lbs (54.4 kg).
DIMENSIONS: 59 x 61 in. (1,498.6 x 1,549.4 mm).
WEIGHT: 65 lbs (29.5 kg).
SUPPORTING TOOLS: None required.
TOOL MAINTENANCE: Coat treated surfaces (black oxide or black phosphate) with
corrosion preventive light oil when stored. Load test periodically (see GE
drawing 2C14725 for load test diagram and applicable NOTE).
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS LIST
GROUP PART NO. NOMENCLATURE QUANTITY SUPPLIER
NUMBER
G02 2C14725P03 U Bolt 1 CODE
FOR ALL
2C14725G02
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C14725G02
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
ADAPTER, PEDESTAL - ENGINE, FORWARD
2C14726G03
PURPOSE AND USE: The Pedestal Adapter is used to support the engine through the
fan case during various maintenance operations and during storage.
DESCRIPTION: The Pedestal Adapter is two C-shaped brackets with bosses at
two locations. The tool has a black oxide or black phosphate finish. This
tool is applicable to CF6-80C2 PMC engines only.
DIMENSIONS: 33 x 14 x 7 in. (838 x 356 x 178 mm).
WEIGHT: 120 lbs (54 kg).
SUPPORTING TOOLS: 2C6339.
TOOL MAINTENANCE: Apply corrosion preventive oil to all surfaces that
have black oxide or black phosphate coating.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing 2C14726.
FOR PMC
2C14726G03
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR PMC
2C14726G03
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
ADAPTER, PEDESTAL - ENGINE, FORWARD
2C14726G04
PURPOSE AND USE: The Pedestal Adapter is used to support the engine through the
fan case during various maintenance operations and during storage.
DESCRIPTION: The Pedestal Adapter is two C-shaped brackets with bosses
at two locations. The tool has a black oxide or black phosphate finish.
This tool is obsolete and was superseded by G05. This tool is applicable
to CF6-80C2 FADEC engines only.
DIMENSIONS: 33 x 14 x 7 in. (838 x 356 x 178 mm).
WEIGHT: 120 lbs (54 kg).
SUPPORTING TOOLS: 2C6339.
TOOL MAINTENANCE: Apply corrosion preventive oil to all surfaces that
have black oxide or black phosphate coating.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing 2C14726.
FOR FADEC
2C14726G04
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR FADEC
2C14726G04
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
ADAPTER, PEDESTAL - ENGINE, FORWARD
2C14726G05
PURPOSE AND USE: The Pedestal Adapter is used to support the engine through the
fan case during various maintenance operations and during storage.
DESCRIPTION: The Pedestal Adapter is two C-shaped brackets with bosses
at two locations. The tool has a black oxide or black phosphate finish.
This tool changes the adapter brackets from 2C14726G04 and is applicable
to CF6-80C2 FADEC engines only.
DIMENSIONS: 33 x 14 x 7 in. (838 x 356 x 178 mm).
WEIGHT: 120 lbs (54 kg).
SUPPORTING TOOLS: 2C6339.
TOOL MAINTENANCE: Apply corrosion preventive oil to all surfaces that
have black oxide or black phosphate coating.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing 2C14726.
FOR FADEC
2C14726G05
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR FADEC
2C14726G05
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
TOOL, REMOVAL, HIGH PRESSURE TURBINE STAGE 1
2C14727G01
PURPOSE AND USE: To remove stage 1 HPT shroud from nozzle support during overhaul.
DESCRIPTION: This tool consists of a special plier jaw, which firmly grip the
shroud and forces the aft shroud end radially inward. The impact hammer is
used to drive the shroud aft and out of the nozzle support.
DIMENSIONS: 17 x 2 x 12 in. (432 x 51 x 304 mm).
WEIGHT: 12 lb (6 kg).
SUPPORTING TOOLS: None required.
TOOL MAINTENANCE: Coat treated surfaces (black oxide or black phosphate)
with corrosion preventive light oil when stored.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS LIST
GROUP PART NO. NOMENCLATURE QUANTITY SUPPLIER
NUMBER CODE
G01 2C14727P02 Side Keyed Plate 1
2C14727P03 Side Plate 1
2C14727P04 Jaw 1
2C14727P05 Spacer 1
2C14727P06 Dowel Pin 1
2C14727P07 Bushing 1
2C14727P08 Geared Handle 1
2C14727P09 Stationary Handle 1
2C14727P10 Ram Block 1
SP80 Seal Puller 1 DE
FOR ALL
2C14727G01
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C14727G01
Page 2
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
TEMPLATE, BLEND LIMITS - LEADING EDGE, STAGE 1
2C14728G01
PURPOSE AND USE: To visually inspect the fan blades after leading
edge damage has been repaired.
DESCRIPTION: The template is manufactured from plexiglass, in which limit lines
are etched. It is molded to the blade convex contour and overhangs the leading
edge for the entire length of the airfoil. An alignment bracket is attached
to the template at the midspan platform which is contoured to match and line
up with the midspan surface. A container is provided.
DIMENSIONS: 6 x 3 x 30 in. (152 x 76 x 762 mm).
WEIGHT: 6 lb (3 kg).
SUPPORTING TOOLS: None required.
TOOL MAINTENANCE: TBD
QUANTITY PER OPERATION: One set.
REPLACEMENT PARTS LIST
GROUP PART NO. NOMENCLATURE QUANTITY SUPPLIER
NUMBER CODE
G01 2C14728P02 Template 1
2C14728P03 Container 1
FOR ALL
2C14728G01
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C14728G01
Page 2
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
ADAPTERS, PEDESTAL - COMPRESSOR STATOR, FORWARD
2C14730G01
PURPOSE AND USE: To support the forward end of the compressor stator
case during maintenance and/or storage.
DESCRIPTION: Two adapters are required. They are manufactured from 0.625 in.
(15.88 mm) thick steel with five bolt holes to interface with the flange of the
compressor stator. There are two elongated holes at the bottom of the flange to
interface with the engine supports of the engine or sub-assemblies.
DIMENSIONS: 13 x 13 in. (330 x 330 mm).
WEIGHT: 18 lb (8 kg).
SUPPORTING TOOLS: Engine handling support, 2C6339.
TOOL MAINTENANCE: Coat treated surfaces (black oxide or black phosphate) with
corrosion preventive light oil when stored. Load test periodically (see GE
drawing 2C14730 for load test diagram and applicable NOTE).
QUANTITY PER OPERATION: One set.
REPLACEMENT PARTS LIST
GROUP PART NO. NOMENCLATURE QUANTITY SUPPLIER
NUMBER CODE
G01 2C14730P02 Bracket 1
2C14730P03 Bracket 1
MS35308-338 Socket Head Cap Screw 8
MS51972-2 Plain Hex Nut 8
MS3508-389 Socket Head Cap Screw 2
MS51972-4 Plain Hex Nut 2
FOR ALL
2C14730G01
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C14730G01
Page 2
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
BRACKET SET, SUPPORT - AFT FAN MAINTENANCE UNIT
2C14731G02
PURPOSE AND USE: The Bracket Support Set is used to support the aft end of the
fan module in the horizontal position from an overhead rail.
DESCRIPTION: The Bracket Support Set is two "Y" shaped arms with a shackle
at one end to attach to an overhead rail system and a pin through the prongs
to connect the brackets with the aft fan case.
DIMENSIONS: 6 x 4 x 4 in. (152 x 102 x 102 mm).
WEIGHT: 6 lb (3 kg).
SUPPORTING TOOLS: Overhead Rail System.
TOOL MAINTENANCE: Apply corrosion preventive oil to all surfaces that
have black oxide or black phosphate coating.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing 2C14731.
FOR ALL
2C14731G02
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C14731G02
Page 2
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
TOOL SET, REMOVAL - MAGNETIC SEAL, N1 CONTROL ADAPTER
2C14733G01
PURPOSE AND USE: To pull the magnet and the seal case with the carbon
seal from the N1 control adapter.
DESCRIPTION: This tool set consists of two pullers; one to pull the magnet and one
to pull the seal case with the carbon seal from the adapter housing. A container
is supplied. SB 72-0371 engines do not use tool set 2C14733.
DIMENSIONS: 12 x 8 x 6 in. (305 x 203 x 153 mm).
WEIGHT: 6 lbs (3 kg).
SUPPORTING TOOLS: None required.
TOOL MAINTENANCE: Coat treated surfaces (black oxide or black phosphate)
with corrosion preventive light oil when stored.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS LIST
GROUP PART NO. NOMENCLATURE QUANTITY SUPPLIER
NUMBER CODE
G01 2C14733P02 Puller 1
2C14733P03 Expander 1
2C14733P04 Knob 2
2C14733P05 Sleeve 1
2C14733P06 Puller 1
2C14733P07 Spacer 1
2C14733P08 Screw 1
2C14733P09 Container 1
FOR ALL
2C14733G01
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C14733G01
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
PROTECTOR, FAN SHAFT
2C14734P01
PURPOSE AND USE: To protect the inside diameter of the fan shaft. This
requirement exists when tightening or loosening bolts during disassembly or
assembly of the stage 1 fan disk to or from the fan shaft.
DESCRIPTION: The protector is a developed flat pattern of a cone on polyethylene
high density 0.02 inch (0.5 mm) thick sleeve, natural color.
DIMENSIONS: 7 in. dia x 13 in. (178 mm dia x 330 mm).
WEIGHT: 3 lb (1.4 kg).
SUPPORTING TOOLS: None required.
TOOL MAINTENANCE: TBD
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: None required.
FOR ALL
2C14734P01
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C14734P01
Page 2
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FIXTURE, RUNOUT - FAN STATOR SUPPORT
2C14735G01
PURPOSE AND USE: The Runout Fixture is used to check the runout between the
No. 1 bearing housing and the stage 5 fan stator support.
DESCRIPTION: The Runout Fixture is a circular support plate mounted on
an L-shaped arm with a bracket to hold a dial indicator. The tool has
a black oxide or black phosphate finish.
DIMENSIONS: 20 x 25 x 20 in. (508 x 635 x 508 mm).
WEIGHT: 35 lb (16 kg).
SUPPORTING TOOLS: None.
TOOL MAINTENANCE: Apply corrosion preventive oil to all surfaces that
have black oxide or black phosphate coating.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing 2C14735.
FOR ALL
2C14735G01
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C14735G01
Page 2
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FIXTURE, RUNOUT - FAN STATOR SUPPORT
2C14735G02
PURPOSE AND USE: The Runout Fixture is used to check the runout between the
No. 1 bearing housing and the stage 5 fan stator support.
DESCRIPTION: The Runout Fixture is a circular support plate mounted on
an L-shaped arm with a bracket to hold a dial indicator. The tool has
a black oxide or black phosphate finish.
DIMENSIONS: 20 x 25 x 20 in. (508 x 635 x 508 mm).
WEIGHT: 35 lb (16 kg).
SUPPORTING TOOLS: None.
TOOL MAINTENANCE: Apply corrosion preventive oil to all surfaces that
have black oxide or black phosphate coating.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing 2C14735.
FOR ALL
2C14735G02
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C14735G02
Page 2
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FIXTURE, LIFT - FAN MAINTENANCE UNIT
2C14736G01
PURPOSE AND USE: To lift the fan maintenance unit using a single hoist.
DESCRIPTION: This lift fixture consists of a fabricated body assembly with a plate
on each end. A lift sling connects to a plate which interfaces with the forward fan
case. A second lift sling connects to a lift bar, which interfaces with the aft fan
case. Turning of a lead screw changes the center of gravity in a horizontal plane.
DIMENSIONS: 55 x 20 x 8 in. (1,400 x 510 x 205 mm).
WEIGHT: 60 lbs (28 kg).
SUPPORTING TOOLS: Used with overhead hoist.
TOOL MAINTENANCE: Coat treated surfaces (black oxide or black phosphate) with
corrosion preventive light oil when stored. Load test periodically (see GE
drawing 2C14736 for load test diagram and application NOTE).
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS LIST
GROUP PART NO. NOMENCLATURE QUANTITY SUPPLIER
NUMBER CODE
G01 2C14736P02 Body 1
2C14736P03 Lead Screw 1
2C14736P04 Handle 1
2C14736P05 Swivel Nut 1
2C14736P06 Lift Bar 2
2C14736P07 Pin 2
2C14736P08 Plate 1
2C14736P09 Bearing 2
2C14736P10 Washer 2
2C14736P11 Spacer 1
2C14736P12 Frame 2
2C14736P13 Washer 4
2C14736P14 Spacer 2
2C14736P15 Bracket 2
2C14736P16 Wear Strip 2
2C14736P31 Plate 1
S2130-437 Anchor Shackle 8 AC
12705-16C-63B Shoulder Screw 2 U
S2130-875 Anchor Shackle 1 AC
FOR ALL
2C14736G01
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C14736G01
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
LIFT ADAPTER FAN CASE AND FRAME AFT
2C14737G01
PURPOSE AND USE: To lift the aft fan case when used with the fan lift fixture.
DESCRIPTION: The adapter consists of a mounting plate, arm, and bracket.
DIMENSIONS: 16 x 9 x 4 in. (410 x 230 x 100 mm).
WEIGHT: 10 lb (5 kg).
SUPPORTING TOOLS: Lift fixture, Fan Maintenance Unit 2C14736.
TOOL MAINTENANCE: Coat treated surfaces (black oxide or black phosphate) with
corrosion preventive light oil when stored. Load test periodically (see GE
drawing 2C14737 for load test diagram and applicable NOTE).
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS LIST
GROUP PART NO. NOMENCLATURE QUANTITY SUPPLIER
NUMBER CODE
G01 2C14737P02 Plate 1
2C14737P03 Arm 1
2C14737P04 Bracket 1
Size 0.437 Anchor Shackle 1 AC
FOR ALL
2C14737G01
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C14737G01
Page 2
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
ADAPTER SET, INSTALL/REMOVE - STAGE 1 FAN DISK NUTS
2C14738G01
PURPOSE AND USE: To torque or loosen the nuts that secure the stage 1
fan disk to the fan forward shaft.
DESCRIPTION: The adapter set consists of an extension bar with a plastic coating
on the shank. It interfaces with the aft end of the spline socket. The spline
socket has a plastisol coating on the outside diameter.
DIMENSIONS: 2 in. dia x 12 in. (51 mm dia x 305 mm).
WEIGHT: 3 lb (1.2 kg).
SUPPORTING TOOLS: Torque wrench.
TOOL MAINTENANCE: None required.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS LIST
GROUP PART NO. NOMENCLATURE QUANTITY SUPPLIER
NUMBER CODE
G01 2C14738P02 Extension Bar 1
2C14738P03 Spline Socket 1
FOR ALL
2C14738G01
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C14738G01
Page 2
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
PULLER, STATIONARY AIR/OIL SEAL - NO. 1 BEARING
2C14740G01
PURPOSE AND USE: To pull No. 1 bearing stationary air/oil seal from
the No. 1 bearing aft housing.
DESCRIPTION: This puller consists of a puller plate, a pusher plate, a
center shaft, and three puller arms.
DIMENSIONS: 34 in. dia x 9 in. (864 mm dia x 229 mm).
WEIGHT: 40 lb (18 kg).
SUPPORTING TOOLS: None required.
TOOL MAINTENANCE: Coat treated surfaces (black oxide) with corrosion
preventive light oil when stored.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS LIST
GROUP PART NO. NOMENCLATURE QUANTITY SUPPLIER
NUMBER CODE
G01 2C14740P02 Puller Plate 1
2C14740P03 Pusher Plate 1
2C14740P04 Shaft 1
2C14740P05 Puller Arm 2
2C14740P06 Indicator Handle 2
2C14740P07 Puller Arm 1
2C14740P08 Knurled Nut 1
2C14740P09 Stop Nut 2
K5-N Stubby Spring Plunger 2 C
FOR ALL
2C14740G01
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C14740G01
Page 2
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
DELETED
2C14741G01
PURPOSE AND USE: This tool has been deleted in its entirety.
FOR ALL
2C14741G01
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
STAND, MAINTENANCE - FAN MAINTENANCE UNIT
2C14742G03
PURPOSE AND USE: The Maintenance Stand is used to support the fan
maintenance unit (FMU) during assembly and disassembly and to transport
the fan module to and from buildup.
DESCRIPTION: The Maintenance Stand consists of a rectangular base on wheels
with four uprights that hold the mounting brackets. An elevated support holds
the fan shaft. The primary color of the tool is blue.
DIMENSIONS: 100 x 100 x 75 in. (2540 x 2540 x 1905 mm).
WEIGHT: 1000 lb (454 kg).
SUPPORTING TOOLS: 2C6350, 2C14737, 2C14751.
TOOL MAINTENANCE: Apply corrosion preventive oil to all surfaces that have black
oxide or black phosphate coating. Coat all unplated or unpainted surfaces
with a preventive compound. Refer to MIL-C-16173, Grade 3.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing 2C14742.
FOR ALL
2C14742G03
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C14742G03
Page 2
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
RACE, BEARING - NO. 4R - DUMMY
2C14743P02
PURPOSE AND USE: The Bearing Race is used to protect the No. 4R bearing
journal during grind, balancing, and EROM inspection.
DESCRIPTION: The Bearing Race is a hardened steel ring with a lip at one end.
The tool has a black oxide or black phosphate finish.
DIMENSIONS: 8 x 2 in. (203 x 51 mm).
WEIGHT: 2 lb (1 kg).
SUPPORTING TOOLS: 2C8018, 2C8080.
TOOL MAINTENANCE: Apply corrosion preventive oil to all surfaces that
have black oxide or black phosphate coating.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing 2C14743.
FOR ALL
2C14743P02
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C14743P02
Page 2
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FIXTURE, HOLD - NO. 4B BEARING
2C14744G01
PURPOSE AND USE: To retain the No. 4B bearing cage and ball assembly
radially outward during normal shop handling, transportation, and inspection
of the compressor rear frame module.
DESCRIPTION: The retaining fixture consists of a nylon ring fitted with an o-ring to
prevent disengagement of the fixture when the module is in vertical position.
DIMENSIONS: 7.5 x 1.5 in. (190 x 38 mm).
WEIGHT: 25 lb (12 kg).
SUPPORTING TOOLS: None required.
TOOL MAINTENANCE: None required.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS LIST
GROUP PART NO. NOMENCLATURE QUANTITY SUPPLIER
NUMBER CODE
G01 2C14744P02 Ring 1
2C14774P03 O-Ring 1
FOR ALL
2C14744G01
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C14744G01
Page 2
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
TOOL, INSTALLATION - WEAR SLEEVE, HORIZONTAL DRIVE SHAFT HOUSING
2C14745G01
PURPOSE AND USE: To aid in the assembly of the wear sleeve to the
horizontal drive shaft housing.
DESCRIPTION: The tool consists of a pilot and a sleeve. The pilot interfaces
with the drive shaft housing at one end and is knurled to provide a gripping
surface at the opposite end. A cone is machined on the outside diameter
of the pilot to allow expansion of the wear sleeve as it is installed over
the housing. One end of the sleeve has eight fingers, which expand while
pushing the wear sleeve over the housing.
DIMENSIONS: 3 x 10 in. (76 x 254 mm).
WEIGHT: 5 lb (2.5 kg).
SUPPORTING TOOLS: None required.
TOOL MAINTENANCE: Coat treated surfaces (black oxide or black phosphate)
with corrosion preventive light oil when stored.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS LIST
GROUP PART NO. NOMENCLATURE QUANTITY SUPPLIER
NUMBER CODE
G01 2C14745P02 Pilot 1
2C14745P03 Sleeve 1
FOR ALL
2C14745G01
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C14745G01
Page 2
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
BRACKET, SHIPPING - COMPRESSOR REAR FRAME AFT SUMP SUPPORT
2C14746G01
PURPOSE AND USE: To support the compressor rear frame aft sump during shipment
and storage of the simplified compressor rear frame.
DESCRIPTION: This bracket consists of a molded support (made from polyester) and
socket head cap screws nuts and washers. A nylon draw string bag is furnished for
safe-keeping of the hardware. The support mounts to the compressor rear frame.
The vertical centerline is marked on the support for alignment.
DIMENSIONS: 15 in. dia x 1 in. (381 mm dia x 25 mm).
WEIGHT: 3 lb (1.5 kg).
SUPPORTING TOOLS: None required.
TOOL MAINTENANCE: TBD
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS LIST
GROUP PART NO. NOMENCLATURE QUANTITY SUPPLIER
NUMBER CODE
G01 2C14746G01 Support 1
MS16996-39B Socket Head Cap Screws 6
0.375-24UNF-3A x
0.75 long
MS35650-3384 Plain Hex Nut 9
0.375-24UNF-2B
MS9321-12 Plain Flat Steel 9
Washer for 0.375
dia fastener
Coml Draw String Nylon Bag 1
8.0 x 6.5
FOR ALL
2C14746G01
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C14746G01
Page 2
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FIXTURE, ASSEMBLY AND TEST - THRUST REVERSER
2C14748G01
PURPOSE AND USE: The Assembly and Test Fixture is used to assemble and test the
thrust reverser halves by simulating the aircraft pylon.
DESCRIPTION: The Assembly and Test Fixture consists of a frame, a brace, six
pylon side hinges, thrust channels, and inner thrust rings (left and right
handed). The primary color of the tool is blue.
DIMENSIONS: 96 x 63 in. (2438 x 1600 mm).
WEIGHT: 300 lb (136 kg).
SUPPORTING TOOLS: Positioning Fixture, Aronson No. HC60A-3,
with B4RT60 Roundtable, 2C14750.
TOOL MAINTENANCE: Apply corrosion preventive compound to all surfaces that
are unplated or unpainted. Refer to MIL-C-16173, Grade 3.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing 2C14748.
FOR ALL
2C14748G01
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C14748G01
Page 2
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FIXTURE, ASSEMBLY AND TEST - THRUST REVERSER
2C14748G02
PURPOSE AND USE: The Assembly and Test Fixture is used to assemble and test the
thrust reverser halves by simulating the aircraft pylon.
DESCRIPTION: The Assembly and Test Fixture consists of a frame, a brace, six
pylon side hinges, thrust channels, and inner thrust rings (left and right
handed). The primary color of the tool is blue.
DIMENSIONS: 96 x 63 in. (2438 x 1600 mm).
WEIGHT: 300 lb (136 kg).
SUPPORTING TOOLS: Positioning Fixture, Aronson No. HC60A-3,
with B4RT60 Roundtable, 2C14750.
TOOL MAINTENANCE: Apply corrosion preventive compound to all surfaces that
are unplated or unpainted. Refer to MIL-C-16173, Grade 3.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing 2C14748.
FOR ALL
2C14748G02
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C14748G02
Page 2
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
PULLER, NO. 3R BEARING AIR SEALS AND HOUSING
2C14749G01
PURPOSE AND USE: To separate the No. 3 roller bearing air seal and
damper housing from the fan frame.
DESCRIPTION: Consists of a base, a ring, six pulling screws, and three jack screws.
DIMENSIONS: 17 x 34 x 5 in. (432 x 864 x 127 mm).
WEIGHT: 40 lb (18 kg).
SUPPORTING TOOLS: None.
TOOL MAINTENANCE: Coat black oxided surfaces with corrosion preventive oil.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS LIST
GROUP PART NO. NOMENCLATURE QUANTITY SUPPLIER
NUMBER CODE
G01 2C14749P02 Puller, Base 1
2C14749P03 Puller, Ring 1
2C14749P04 Screw, Cap 6
FOR ALL
2C14749G01
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C14749G01
Page 2
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
SLING, AFT, THRUST REVERSER HALF
2C14750G01
PURPOSE AND USE: To install and remove the fan reverser to and
from 2C14748 test fixture.
DESCRIPTION: The fixture consists of an adjustable CG spreader bar, two
seven-foot lift puller hoists, and four bracket strap assemblies. The
fixture also consists of three hinge guide pins.
DIMENSIONS: 70 x 24 x 24 in. (1778 x 610 x 610 mm).
WEIGHT: 50 lb (23 kg).
SUPPORTING TOOLS: None.
TOOL MAINTENANCE: None.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS LIST
GROUP PART NO. NOMENCLATURE QUANTITY SUPPLIER
NUMBER CODE
G01 2C14750P02 Bracket, Lift 2
2C14750P03 Bracket, Lift 2
2C14750P04 Plate, Lift 2
2C14750P05 Bar, Spreader 1
2C14750P06 Spacer 2
2C14750P07 Plate, Slide 2
2C14750P08 Block, Threaded 1
2C14750P09 Bracket 1
2C14750P10 Rod, Threaded 1
2C14750P11 Wheel, Hand 1
2C14750P12 Strap, Spacer 2
2C14750P13 Strap, Aft 1
2C14750P14 Strap, Fwd 1
2C14750P15 Bushing, Lock 1
2C14750P34 Guide, Hinge Pin 3
2C14750P35 Retainer, Stud 3
FOR ALL
2C14750G01
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C14750G01
Page 2
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FIXTURE LIFT - FAN STATOR FORWARD
2C14751G01
PURPOSE AND USE: To install the forward fan stator case to and remove from
the engine when the engine is horizontal. It will also allow to turn the
stator case vertical for maintenance operations.
DESCRIPTION: This lift fixture consists of a "L" shaped fabricated arm assembly (a
tubular structure welded to a plate), which attaches to the forward fan stator case.
DIMENSIONS: 50 x 24 x 27 in. (1270 x 610 x 690 mm).
WEIGHT: 110 lb (50 kg).
SUPPORTING TOOLS: Overhead Crane.
TOOL MAINTENANCE: Coat treated surfaces (black oxide or black phosphate) with
corrosion preventive light oil when stored. Load test periodically (see GE
drawing 2C14751 for load test diagram and applicable NOTE).
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS LIST
GROUP PART NO. NOMENCLATURE QUANTITY SUPPLIER
NUMBER CODE
G01 2C14751P02 Mounting Arm 1
2C14751P03 Lift Eye 1
2C14751P04 Stop 1
BLS8BC40S Ball-Lok Pin 1 A
FOR ALL
2C14751G01
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C14751G01
Page 2
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
CONTAINER, SHIPPING - STAGE 1 HPT NOZZLE ASSEMBLY
2C14752G01
PURPOSE AND USE: To ship or store the stage 1 high pressure turbine
nozzle. The nozzle is being restrained, and the container can be placed
in either vertical or horizontal positions.
DESCRIPTION: This shipping container is a square wooden structure consisting
of three inseparable assemblies, box, clamp, and cover.
DIMENSIONS: 46 x 46 x 14 in. (1,170 x 1,170 x 355 mm).
WEIGHT: 60 lbs (28 kg).
SUPPORTING TOOLS: Lift fixture, 2C14695.
TOOL MAINTENANCE: None required.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS LIST
GROUP PART NO. NOMENCLATURE QUANTITY SUPPLIER
NUMBER CODE
G01 2C14752P02 Box 1
2C14752P03 Clamp 1
2C14752P04 Cover 1
FOR ALL
2C14752G01
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C14752G01
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
CONTAINER, SHIPPING - ACCESSORY GEARBOX
2C14753G01
PURPOSE AND USE: To provide a shipping container for the accessory gearbox (without
accessories) that gives protection of the bearing from vibration during shipping.
DESCRIPTION: Container is a wooden structure with neoprene bumper pads on the four
sides, supported on vibration isolation mounts, and held down with two straps.
DIMENSIONS: 16 x 32 x 55 in. (406 x 813 x 1397 mm).
WEIGHT: 150 lb (68 kg).
SUPPORTING TOOLS: None.
TOOL MAINTENANCE: None.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS LIST
GROUP PART NO. NOMENCLATURE QUANTITY SUPPLIER
NUMBER CODE
G02 2C14753P02 Box 1
2C14753P03 Lid 1
2C14753P04 Plate, Support 1
2C14753P05 Plate, Support 1
2C14753P06 Plate, Support 1
2C14753P07 Plate, Support 1
2C14753P08 Shim 1
FOR ALL
2C14753G01
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C14753G01
Page 2
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FIXTURE, ALIGN - LOW PRESSURE TURBINE COOLING
2C14754G01
PURPOSE AND USE: The Align Fixture is used to align the flex slide joints when
installing into the low pressure turbine (LPT) case.
DESCRIPTION: The Align Fixture consists of thirteen identical clamps
made of two halves with a hinge on one side and a swing bolt on the
other side. A container is provided.
DIMENSIONS: 8 x 16 x 29 in. (203 x 406 x 737 mm).
WEIGHT: 7 lb (3 kg).
SUPPORTING TOOLS: None.
TOOL MAINTENANCE: Apply corrosion preventive oil to all surfaces that
have black oxide or black phosphate coating.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing 2C14754.
FOR ALL
2C14754G01
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C14754G01
Page 2
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
CONTAINER, SHIPPING - FAN BOOSTER
2C14755G01
PURPOSE AND USE: To protect the fan booster module during shipment and storage.
DESCRIPTION: Container consists of a combination of wooden and metal construction
which centers the fan booster module and holds it firmly in place.
DIMENSIONS: 71 x 20 x 50 in. (1803 x 508 x 1270 mm).
WEIGHT: TBD
SUPPORTING TOOLS: 2C14686.
TOOL MAINTENANCE: None.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS LIST
GROUP PART NO. NOMENCLATURE QUANTITY SUPPLIER
NUMBER CODE
G01 2C14755P02 Base 1
2C14755P03 Box, Accessory 2
2C14755P04 Pad 4
2C14755P05 Strut 6
2C14755P06 Cover 1
2C14755P07 Pad 1
2C14755P08 Clamp 1
2C14755P08 Support 1
2C14755P08 Ring Lifting 3
FOR ALL
2C14755G01
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C14755G01
Page 2
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
PRESSURE TEST KIT, FAN REVERSER INFLATABLE AIR SEAL
2C14756G01
FOR ALL
2C14756G01
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C14756G01
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FIXTURE, MACHINING, FAN STATOR CASES
2C14757G01
PURPOSE AND USE: To machine teflon shrouds being replaced during overhaul to size.
DESCRIPTION: This fixture consists of a beam structure 2 x 4 x 24 in. (51
x 102 x 610 mm) long, that has the following design features: 1. A slide
mounted pivoting cutter, that is air driven. 2. A lift eye for a hoist to
raise the unit from and lower it to the inspection fixture 2C6987. 3. A
roller assembly to support the forward outer portion of the tool on a wear
ring mounted on the stage 1 fan case forward flange.
DIMENSIONS: 36 x 27 x 16 in. (915 x 686 x 407 mm).
WEIGHT: 200 lb (91 kg).
SUPPORTING TOOLS: 90 psi filtered and lubricated air supply.
Inspection fixture 2C6987.
TOOL MAINTENANCE: Coat treated surfaces (black oxide or black phosphate)
with corrosion preventive light oil when stored.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: This fixture has an extensive parts list that will be little
value without the drawing. Refer to GE drawing 2C14757.
FOR ALL
2C14757G01
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C14757G01
Page 2
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
TOOL SET, INSTALLATION OR REMOVAL - LPT ROTOR BOLTS, STAGES 1 AND 2
2C14758G01
PURPOSE AND USE: To prevent rotation of stage 1 and stage 2 LPT rotor bolts
during installation and removal of the nuts.
DESCRIPTION: This tool set consists of two "U" shaped ratchet wrenches.
One wrench is used to install or remove the nut. The second wrench
is used to hold the bolt head.
DIMENSIONS: 16 x 8 x 6 in. (407 x 203 x 152 mm).
WEIGHT: 5 lbs (2.5 kg).
SUPPORTING TOOLS: LPT balance tooling, 2C14922.
TOOL MAINTENANCE: Coat treated surfaces (black oxide or black phosphate)
with corrosion preventive light oil when stored.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS LIST
GROUP PART NO. NOMENCLATURE QUANTITY SUPPLIER
NUMBER CODE
G01 2C14758P02 Removal Body Wrench 1
2C14758P03 Wrench 1
2C14758P04 Ratchet Wrench 2
2C14758P05 Container 1
2C14758P06 Installation Body 1
Wrench
FOR ALL
2C14758G01
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C14758G01
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
TOOL SET, INSTALLATION OR REMOVAL - LPT ROTOR BOLTS, STAGES 1 AND 2
2C14758G02
PURPOSE AND USE: To prevent rotation of stage 1 and stage 2 LPT rotor bolts
during installation and removal of the nuts.
DESCRIPTION: This tool set consists of two "U" shaped ratchet wrenches.
One wrench is used to install or remove the nut. The second wrench
is used to hold the bolt head.
DIMENSIONS: 16 x 8 x 6 in. (407 x 203 x 152 mm).
WEIGHT: 5 lbs (2.5 kg).
SUPPORTING TOOLS: LPT balance tooling, 2C14922.
TOOL MAINTENANCE: Coat treated surfaces (black oxide or black phosphate)
with corrosion preventive light oil when stored.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS LIST
GROUP PART NO. NOMENCLATURE QUANTITY SUPPLIER
NUMBER CODE
G02 2C14758P03 Wrench 1
2C14758P05 Container 1
2C14758P08 Ratchet Wrench 2
2C14758P09 Installation Body 1
Wrench
2C14758P10 Removal Body Wrench 1
FOR ALL
2C14758G02
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C14758G02
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
CONTAINER, SHIPPING - COMBUSTION CHAMBER LINER ASSEMBLY
2C14760G01
PURPOSE AND USE: To ship or store the combustion chamber liner assembly.
DESCRIPTION: This shipping container is a square wooden structure consisting
of three inseparable assemblies; a box, clamp, and cover.
DIMENSIONS: 44 x 44 x 24 in. (1120 x 1120 x 610 mm).
WEIGHT: 90 lb (41 kg).
SUPPORTING TOOLS: Combustor lift fixture, 2C14689.
TOOL MAINTENANCE: None required.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS LIST
GROUP PART NO. NOMENCLATURE QUANTITY SUPPLIER
NUMBER CODE
G01 2C14760P02 Box 1
2C14760P03 Cover 1
2C14760P04 Clamp 1
FOR ALL
2C14760G01
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C14760G01
Page 2
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
CONTAINER, SHIPPING - FAN STATOR
2C14761G01
PURPOSE AND USE: To house and protect the fan stator assembly during shipment.
DESCRIPTION: Consists of a plywood box with various brackets, clamps, etc. to
hold and protect the fan stator for shipping or storage.
DIMENSIONS: 103 x 100 x 60 in. (2616 x 2540 x 1524 mm).
WEIGHT: TBD
SUPPORTING TOOLS: TBD
TOOL MAINTENANCE: None.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS LIST
GROUP PART NO. NOMENCLATURE QUANTITY SUPPLIER
NUMBER CODE
G01 2C14761P02 Box 1
2C14761P03 Lid 1
2C14761P04 Ring, Bolt 3
2C14761P05 Wedge 4
2C14761P06 Rod 1
2C14761P07 Post, Center 1
2C14761P08 Clamp, Bearing 1
FOR ALL
2C14761G01
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C14761G01
Page 2
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FIXTURE, HOLDING - LPT ROTOR/STATOR - SPLIT ENGINE SHIPPING
2C14762G01
PURPOSE AND USE: To prevent axial movement of the low pressure turbine
rotor during split engine shipment.
DESCRIPTION: This fixture consists of four parts; drum, carriage, nut, and locknut.
The drum has external threads on one end and a flange on the other end. The nut,
carriage, and locknut are captive on the threaded portion of the drum. The carriage
has three tubes with mounting pads which extend radially outward.
DIMENSIONS: 31 in. dia x 22 in. (787 mm dia x 559 mm).
WEIGHT: 70 lb (32 kg).
SUPPORTING TOOLS: Hand tools.
TOOL MAINTENANCE: Apply a light coat of corrosion preventive compound to
unplated and unpainted surfaces when stored. Load test periodically (see GE
drawing 2C14762 for load test diagram and applicable NOTE).
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS LIST
GROUP PART NO. NOMENCLATURE QUANTITY SUPPLIER
NUMBER CODE
G01 2C14762P02 Pilot Tube 1
2C14762P03 Nut 1
2C14762P04 Retainer 1
2C14762P05 Instruction Card 1
2C14762P06 Support 1
MS35650-304 Nut 6
.190-32UNF-2B
MS35650-3314 Nut 7
.3125-24UNF-2B
FOR ALL
2C14762G01
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C14762G01
Page 2
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FIXTURE, LIFT AND TURN - ENGINE
2C14763G02
PURPOSE AND USE: The Lift and Turn Fixture is used to attach to the AFT end
of the core module to turn the engine (with or without the accessory gearbox
(AGB) assembly) to a horizontal or vertical position.
DESCRIPTION: The Lift and Turn Fixture is a large ring held concentric
by a support structure in the center. A lift link is located in the
center. The tool has a crank with an extender to attach the tool to the
engine. The primary color of the tool is blue.
DIMENSIONS: 39 x 15 in. (991 x 381 mm).
WEIGHT: 125 lb (57 kg).
SUPPORTING TOOLS: Two Overhead Cranes, 10,000 lb (4536 kg)
minimum capacity, 2C14715.
TOOL MAINTENANCE: None.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing 2C14763.
FOR ALL
2C14763G02
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C14763G02
Page 2
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FIXTURE, MOTORING - CORE ENGINE
2C14764G05
PURPOSE AND USE: The Motoring Fixture is used to turn the high pressure turbine
rotor (HPTR) to do a borescope inspection for 115 VAC applications.
DESCRIPTION: The Motoring Fixture is a control box with three cables. The
tool has a black oxide or black phosphate finish.
DIMENSIONS: 10 x 16 x 6 in. (254 x 406 x 152 mm).
WEIGHT: TBD
SUPPORTING TOOLS: 2C14070, 2C14635, 2C14649.
TOOL MAINTENANCE: Apply corrosion preventive oil to all surfaces that
have black oxide or black phosphate coating.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing 2C14764.
FOR ALL
2C14764G05
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C14764G05
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FIXTURE, MOTORING - CORE ENGINE
2C14764G06
PURPOSE AND USE: The Motoring Fixture is used to turn the high pressure turbine
rotor (HPTR) to do a borescope inspection for 220 VAC applications.
DESCRIPTION: The Motoring Fixture is a control box with three cables. The
tool has a black oxide or black phosphate finish.
DIMENSIONS: 10 x 16 x 6 in. (254 x 406 x 152 mm).
WEIGHT: TBD
SUPPORTING TOOLS: 2C14070, 2C14635, 2C14649.
TOOL MAINTENANCE: Apply corrosion preventive oil to all surfaces that
have black oxide or black phosphate coating.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing 2C14764.
FOR ALL
2C14764G06
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C14764G06
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FIXTURE, CLAMP - HP TURBINE ROTOR DISKS
2C14766G01
PURPOSE AND USE: To clamp the stage 1 and stage 2 HP turbine disks
together so they do not shift while interchanging parts to reduce residual
unbalance during rotor balancing.
DESCRIPTION: This tool consists of three major components: 1. The Support Frame
- This item supports the centering rods, hydraulic cylinder, hydraulic tubing,
pressure regulator, and transmits the clamping forces between the HPT rotor
stage 2 disk aft face and the HPT rotor stage 1 disk bore. The centering rods,
which are an integral part of the frame, have a larger diameter offset at one
end that can be turned to either engage or disengage the bore for installation
and removal. 2. The Extension Rod - This transmits the load from the hydraulic
cylinder to the bore plate. 3. The Bore Plate - This item transmits the
clamping load from the extension rod to the three leg caps.
DIMENSIONS: 20 in. dia x 19 in. (503 mm dia x 483 mm).
WEIGHT: 30 lb (14 kg).
SUPPORTING TOOLS: Hydraulic pump with gage.
TOOL MAINTENANCE: Coat treated surfaces (black oxide or black phosphate)
with corrosion preventive light oil when stored.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS LIST
GROUP PART NO. NOMENCLATURE QUANTITY SUPPLIER
NUMBER CODE
G01 2C14766P02 Support Frame 1
2C14766P03 Plate 1
2C14766P04 Frame Handle 1
2C14766P05 Extension Rod 1
FOR ALL
2C14766G01
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
GROUP PART NO. NOMENCLATURE QUANTITY SUPPLIER
NUMBER CODE
AR-400 Female Coupler 1
FZ-1612 Tee Fitting 1
6-6-FBTX-SS Male Connector 1 V
2084-6S-2 Extension Nipple 1 P
133091 Steel Chain Ring 6 ER
8 Sash Chain 3 R
CL-6-BLP-B-2.2-S Ball-Lok Pin 3 I
FP-3 Eye Bolt 1 C
1/4 FFF4.00 Pipe Nipple 1
V8 Shut-off Valve 1
FZ-1617 Hex Nipple 1
6DBTX-SS Female Elbow 1
FOR ALL
2C14766G01
Page 2
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C14766G01
Page 3
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FIXTURE, CLAMP - HP TURBINE ROTOR DISKS
2C14766G02
PURPOSE AND USE: To clamp the stage 1 and stage 2 HP turbine disks
together so they do not shift while interchanging parts to reduce residual
unbalance during rotor balancing.
DESCRIPTION: This tool consists of three major components: 1. The Support
Frame - This item supports the centering rods, hydraulic cylinder, hydraulic
tubing, pressure regulator, and transmits the clamping forces between the
HPT rotor stage 2 disk aft face and the HPT rotor stage 1 disk bore. The
centering rods, which are an integral part of the frame, have a larger diameter
offset at one end that can be turned to either engage or disengage the bore
for installation and removal. 2. The Extension Rod - This transmits the
load from the hydraulic cylinder to the bore plate. 3. The Bore Plate -
This item transmits the clamping load from the extension rod to the three leg
caps. The G02 version is used with Post SB 72-1313 engines.
DIMENSIONS: 20 in. dia x 19 in. (503 mm dia x 483 mm).
WEIGHT: 30 lbs (14 kg).
SUPPORTING TOOLS: Hydraulic pump with gage.
TOOL MAINTENANCE: Coat treated surfaces (black oxide or black phosphate)
with corrosion preventive light oil when stored.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS LIST
GROUP PART NO. NOMENCLATURE QUANTITY SUPPLIER
NUMBER CODE
G02 2C14766P11 Valve Clamp 1
2C14766P36 Block 1
2C14766P37 Clamp 1
RCP-25 Hydraulic Cylinder 1 D
V-152(3400 PSI) Control Valve 1
AR-400 Female Coupler 1
FZ-1612 Tee Fitting 1
6-6-FBTX-SS Male Connector 1 V
2084-6S-2 Extension Nipple 1 P
FP-3 Eye Bolt 1 C
1/4 FFF4.00 Pipe Nipple 1
V8 Shut-off Valve 1
FZ-1617 Hex Nipple 1
6DBTX-SS Female Elbow 1
FOR ALL
2C14766G02
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C14766G02
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FIXTURE, INSPECTION - 4R/4B AND 4B LUBE NOZZLE
2C14767P01
PURPOSE AND USE: To check the depth of the lube nozzles during compressor rear frame
buildup. This assures clearance between the No. 4R or 4B lube nozzle and the
outside diameter of the No. 4R bearing inner spanner nut and the clearance between
the 4B aft lube nozzle and the No. 4R and 5R heat shield outside diameter.
DESCRIPTION: The fixture is a one piece construction. The aft end has concentric
diameters. The smaller diameter interfaces with the inside diameter of the No. 4B
bearing housing. The larger diameter forms a lip, which serves as a stop that rests
on the aft side of the No. 4B bearing housing flange. The fixture has two other
diameters. One diameter interfaces with the No. 4B bearing aft lube nozzle, near
the midpoint. The other diameter interfaces with the No. 4R/4B bearing lube nozzle
at the forward end. A rectangular cutout provides a means to grip the fixture.
DIMENSIONS: 11 x 6 x 5 in. (280 x 152 x 127 mm).
WEIGHT: 7 lbs (3 kg).
SUPPORTING TOOLS: None required.
TOOL MAINTENANCE: None required.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: None required.
FOR ALL
2C14767P01
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C14767P01
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
TOOL SET, INSTALLATION OR REMOVAL, STAGE 1 FAN DISK NUTS
2C14769G03
PURPOSE AND USE: The Tool Set is used to tighten or loosen the stage 1 fan
nuts during booster installation or removal.
DESCRIPTION: The Tool Set consists of a mounting plate, two antitorque
tools, and a spline drive tool.
DIMENSIONS: 36 x 14 x 14 in. (914 x 356 x 356 mm).
WEIGHT: 35 lb (16 kg).
SUPPORTING TOOLS: Sweeney Wrenches 103, 392, and 393, 2C14680, 2C6827, 2C6075.
TOOL MAINTENANCE: Apply corrosion preventive oil to all surfaces that
have black oxide or black phosphate coating.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing 2C14769.
FOR ALL
2C14769G03
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C14769G03
Page 2
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FIXTURE, INSPECT - LPT NOZZLE ASSEMBLY, STAGE 1
2C14770G01
PURPOSE AND USE: To perform run-out/drop check inspections on the forward side of
the 1st stage nozzle assembly and to axial load the pressure balance seal.
DESCRIPTION: The tool is composed of a base structure consisting of a 44 in. O.D.
x 3.5 in. I.D. x 0.62 in. (1,118 mm O.D. x 88.9 mm I.D. x 15.7 mm) thick plate
supported by vertical 19 in. (483 mm) high tubular legs. A tubular, spoked ring
attached to the legs and in the center of the spokes is a roller bearing mounted
shaft. An inspection arm attaches to the bearing mounted shaft. The inspection
arm is calibrated to read both runout and actual radii. A precision machined plate
is part of the main tool frame for taking required axial drop dimensions. Four
pneumatic cylinders attach to the tool frame to load the pressure balance seal aft.
A pressure regulator and on-off valve complete the pneumatic system. A lift and
turn bar are provided to permit inverting the LP turbine case assembly.
DIMENSIONS: 44 in. dia x 25 in. (1,118 mm dia x 635 mm).
WEIGHT: 200 lbs (91 kg).
SUPPORTING TOOLS: 90 psi (621 kPa) filtered, lubricated air supply.
TOOL MAINTENANCE: None.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: This fixture has an extensive parts list that will be of
little value without the drawing. Refer to GE Drawing 2C14770.
FOR ALL
2C14770G01
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C14770G01
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FIXTURE, LIFT/TURN - LP TURBINE MODULE - AFT
2C14771G01
PURPOSE AND USE: To lift and turn the LP turbine module to a proper position to
perform inspection on the stage 1 low pressure turbine nozzle assembly.
DESCRIPTION: This tool consists of a two legged sling. Attached to each
leg is a swivel eye and plate to interface with the aft low pressure turbine
case restraint ring, 2C14208. Four cylindrical feet are also provided to
permit the case to set on the floor, forward end up.
DIMENSIONS: 6 x 12 x 6 in. (152 x 305 x 152 mm).
WEIGHT: 8 lb (4 kg).
SUPPORTING TOOLS: Fixtures, 2C14208, 2C14770, 2C14772, and two hoists.
TOOL MAINTENANCE: Coat treated surfaces (black oxide or black phosphate) with
corrosion preventive light oil when stored. Load test periodically (see GE
drawing 2C14771 for load test diagram and applicable NOTE).
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS LIST
GROUP PART NO. NOMENCLATURE QUANTITY SUPPLIER
NUMBER CODE
G01 2C14771P02 Two Leg Sling 1
2C14771P03 Adapter Plate 2
2C14771P04 Spacer Leg 4
2C14771P05 Sling Tag 1
2C14771P06 Plate Screw 4
2C14771P07 Leg Screw 4
Size 1/4 Anchor Shackle 2 AC
ADB-23051 Hoist Ring 2 Z
133091 Steel Chain Ring 2 ER
8 Nickel Plated Sash 1 R
Chain
MS21301-1 Shoulder Bolt 2
MS35691-B1l Plain Nut 2
MS15795-812B Flat Washer 4
FOR ALL
2C14771G01
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C14771G01
Page 2
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FIXTURE, CLAMPING - STAGE 1 LOW PRESSURE TURBINE SHROUD
2C14772G01
PURPOSE AND USE: To retain nozzles and stage 1 shrouds in position while turning
the low pressure turbine case during low pressure turbine module build up.
DESCRIPTION: This fixture consists of a ring and eight equally spaced swing clamps.
DIMENSIONS: 42 in. dia x 4 in. (1067 mm dia x 102 mm).
WEIGHT: 12 lbs (6 kg).
SUPPORTING TOOLS: Inspection fixture, 2C14770.
TOOL MAINTENANCE: Coat treated surfaces (black oxide or black phosphate)
with corrosion preventive light oil when stored.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS LIST
GROUP PART NO. NOMENCLATURE QUANTITY SUPPLIER
NUMBER CODE
G01 2C14772P02 Ring 1
2C14772P03 Swing Clamp 8
2C14772P04 Screw 8
5100-31 Retainer Ring 8 J
8-HL-5/16 x 1/2 x 1/2 Head Liner Bushing 8 I
FOR ALL
2C14772G01
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C14772G01
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
GAGE, FLOW AREA - HIGH PRESSURE TURBINE NOZZLE
2C14774G04
PURPOSE AND USE: The Flow Area Gage is used to check the area of individual nozzles
as well as the total area of the nozzle assembly during engine overhaul.
DESCRIPTION: The Flow Area Gage consists of a gage, master, and container.
DIMENSIONS: 12 x 12 x 8 in. (305 x 305 x 203 mm).
WEIGHT: 15 lb (7 kg).
SUPPORTING TOOLS: None.
TOOL MAINTENANCE: It is recommended that periodic checks of gage and
master for operation and accuracy be performed by tool vendor. The time
between checks will vary with gage usage.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing 2C14774.
FOR ALL
2C14774G04
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C14774G04
Page 2
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FIXTURE, RUN ON TORQUE - CENTER VENT TUBE SUPPORT NUTS
2C14775G04
PURPOSE AND USE: The Run On Torque Fixture is used to determine the run on torque
value of the mid shaft support nuts before installation.
DESCRIPTION: The Run On Torque Fixture is a base that supports the center
vent tube support assembly, a lock plate and a wrench head. The tool has
a black oxide or black phosphate finish.
DIMENSIONS: 6 x 4.25 in. (152 x 108 mm).
WEIGHT: 5 lb (2 kg).
SUPPORTING TOOLS: None.
TOOL MAINTENANCE: Apply corrosion preventive oil to all surfaces that
have black oxide or black phosphate coating.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing 2C14775.
FOR ALL
2C14775G04
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C14775G04
Page 2
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
TOOL, INSTALL - MAGNETIC SEAL AND RETAINING RING, N1 CONTROL ADAPTER
2C14776G01
PURPOSE AND USE: To install the magnetic seal assembly into the N1 control
adapter assembly while the adapter assembly is installed on the engine.
The alignment during installation is critical to prevent damage to the
o-ring. This tool fulfills these requirements.
DESCRIPTION: The tool consists of a threaded rod which actuates the fingers
which expand behind the lip of the magnetic seal which threads through a
plunger/pusher which rests on the back side of the magnetic seal to hold
the magnetic seal firmly. The pusher/plunger has external threads which
interface with a split outer case to activate the pusher. The tool is made
of tool steel and is black oxided for corrosion protection. This tool is
non-FADEC only and is item 62 of tool set, 2C14673G04.
DIMENSIONS: 30 in. dia x 8 in. (762 mm dia x 203 mm).
WEIGHT: 3 lbs (1 kg).
SUPPORTING TOOLS: None.
TOOL MAINTENANCE: None.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS LIST
GROUP PART NO. NOMENCLATURE QUANTITY SUPPLIER
NUMBER CODE
G01 2C14776P02 Sleeve 1
2C14776P03 Holder 1
2C14776P04 Pusher 1
2C14776P05 Expander 1
2C14776P06 Knob 1
2C14776P07 Knob 1
2C14776P08 Container 1
2C14776P09 Knob 1
2C14776P10 Adapter 1
FOR PMC
2C14776G01
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR PMC
2C14776G01
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
GAGE, INSPECT - HPT BLADE STAGE 1 TRAILING EDGE
2C14777G01
PURPOSE AND USE: To inspect the trailing edge for distortion or bowing.
DESCRIPTION: The fixture consists of an "L" shaped steel base with a handle.
The long side of the "L" is angled to approximate the airfoil contour. Two
construction balls are used to locate the blade radially, and two construction
balls are used to contact the airfoil. The handle has an angled surface to
locate against the angled side of the blade. A dial indicator measures bow
or displacement, and a set master is also provided.
DIMENSIONS: 3 x 2.2 x 1.5 in. (76 x 56 x 38 mm).
WEIGHT: 1 lb (0.5 kg).
SUPPORTING TOOLS: None.
TOOL MAINTENANCE: Lightly coat black oxide or black phosphate surfaces
with corrosion preventive oil.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS LIST
GROUP NAME PART NUMBER QUANTITY SUPPLIER
NUMBER CODE
G01 Body 2C14777P02 1
Set Master 2C14777P03 1
Container 2C14777P04 1
FOR ALL
2C14777G01
Page 1
Dec 01/2014
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C14777G01
Page 2
Dec 01/2014
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
TOOL SET, POSITION - LUBE AND SCAVENGE TUBE, TRF
2C14778G01
PURPOSE AND USE: To position and restrain the oil supply and
scavenge tubes while welding.
DESCRIPTION: Consists of adapters, an inner base plate and an outer base plate.
DIMENSIONS: 14 x 11 x 6 in. (356 x 279 x 152 mm).
WEIGHT: 75 lb (34 kg).
SUPPORTING TOOLS: None.
TOOL MAINTENANCE: Coat black oxided or black phosphate surfaces
with corrosion preventive oil.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS LIST
GROUP PART NO. NOMENCLATURE QUANTITY SUPPLIER
NUMBER CODE
G01 2C14778P02 Plate, Base Outer 1
2C14778P03 Adapter, Female, 1
Scav. Tube
2C14778P04 Adapter, Female, Oil 1
Supply Tube
2C14778P05 Plate, Base Inner 1
2C14778P06 Adapter, Male, Scav. 1
Tube
2C14778P07 Adapter, Male, Oil 1
Supply Tube
2C14778P08 Container 1
FOR ALL
2C14778G01
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C14778G01
Page 2
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
TOOL SET, ALIGNMENT - COMPRESSOR HORIZONTAL FLANGE
2C14779G02
PURPOSE AND USE: The Alignment Tool Set is used to improve the alignment of the
compressor horizontal flanges to increase efficiency and stall margin.
DESCRIPTION: The Alignment Tool Set consists of sixteen adjustable expansion
alignment pins of five different sizes, a modified flexible socket, and a
container. The tool has a black oxide or black phosphate finish.
DIMENSIONS: 4 x 4 x 8 in. (102 x 102 x 203 mm).
WEIGHT: 1.5 lb (0.7 kg).
SUPPORTING TOOLS: Hand tools.
TOOL MAINTENANCE: Apply corrosion preventive oil to all surfaces that have black
oxide or black phosphate coating. Calibrate every 20th use.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing 2C14779.
FOR ALL
2C14779G02
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C14779G02
Page 2
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
ADAPTER, PEDESTAL - COMPRESSOR REAR FRAME
2C14780G02
PURPOSE AND USE: The Pedestal Adapter is used to support the engine at the junction
of the compressor stator case and the compressor rear frame.
DESCRIPTION: The Pedestal Adapter is a semi-circular frame made of aluminum channel
with brackets attached to each end. The primary color of the tool is blue.
DIMENSIONS: 94 x 59 x 5 in. (2388 x 1499 x 127 mm).
WEIGHT: 145 lb (66 kg).
SUPPORTING TOOLS: Overhead Hoist, 2C6339.
TOOL MAINTENANCE: Coat black oxide or black phosphate treated surfaces
with corrosion preventive oil.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing 2C14780.
FOR ALL
2C14780G02
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C14780G02
Page 2
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
GAGE, TRAILING EDGE BOW - HIGH PRESSURE TURBINE BLADE STAGE 1
2C14781G01
PURPOSE AND USE: The Trailing Edge Bow Gage is used to measure the trailing edge bow
on the stage 1 blades in an assembled high pressure turbine rotor (HPTR).
DESCRIPTION: The Trailing Edge Bow Gage is a U-shaped block with six pin locators
and a dial indicator. The tool has a black oxide or black phosphate finish.
This tool is obsolete and was superseded by 2C14805G01.
DIMENSIONS: 3 x 4 x 4 in. (76 x 102 x 102 mm).
WEIGHT: 2 lbs (1 kg).
SUPPORTING TOOLS: None.
TOOL MAINTENANCE: TBD
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing 2C14781.
FOR ALL
2C14781G01
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C14781G01
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FIXTURE, LIFT - ENGINE, AFT
2C14782G01
FOR ALL
2C14782G01
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C14782G01
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
RING SET, ASSEMBLY - STAGE 2 HPT NOZZLE
2C14783G02
PURPOSE AND USE: To assemble the case and nozzle subassembly onto the
hanger support and stage 1 shroud support.
DESCRIPTION: The fixture consists of two components, an aft assembly ring and
a forward assembly ring. The forward ring is a heavy steel ring which rabbets
onto the HPTN case. It also has twelve strap clamps to hold the assembly to
the fixture. On the back side there are jack plates used to force the HPT
stage 1 shroud support into the slot of the HPT stator case. It also has
two special alignment pins to align the HPT hanger support to the HPT stator
case. Two tapped storage holes are provided for the alignment pins when they
are not being used. The aft ring is a lighter aluminum ring used to assemble
the HPT stage 2 shroud support to the HPT stator case.
DIMENSIONS: 46 in. (1168 mm) dia x 30 in. (763 mm).
WEIGHT: 540 lb (245 kg).
SUPPORTING TOOLS: Crane.
TOOL MAINTENANCE: Apply a light coat of corrosion preventive oil to
treated surfaces when in storage. Load test periodically (see GE
drawing 2C24783 for load test diagram).
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS LIST
GROUP PART NO. NOMENCLATURE QUANTITY SUPPLIER
NUMBER CODE
G02 2C14783P02 Ring, aft 1
2C14783P03 Clamp 12
2C14783P04 Ring, forward 1
2C14783P07 Support 8
2C14783P08 Pin, locating 2
2C14783P10 Clamp 3
2C14783P33 Segment, jacking 24
20097-12C-40B Screw, skt hd cap 48
47311 Hoist, ring 3 F
47312 Hoist, ring 3 F
CL-3-SW Washer, spherical 18 I
CL-5-SW Washer, spherical 48 I
MS15795-814 Washer, flat 3
MS16995-81B Screw, skt hd cap 3
MS16995-99B Screw, skt hd cap 12
MS16995-111B Screw, skt hd cap 8
FOR ALL
2C14783G02
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C14783G02
Page 2
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
RING SET, ASSEMBLY - STAGE 2 HPT NOZZLE
2C14783G03
PURPOSE AND USE: To assemble the case and nozzle subassembly onto the
hanger support and stage 1 shroud support.
DESCRIPTION: The fixture consists of two components, an aft assembly ring and
a forward assembly ring. The forward ring is a heavy steel ring which rabbets
onto the HPTN case. It also has twelve strap clamps to hold the assembly to the
fixture. On the back side there are jack plates used to force the HPT stage 1
shroud support into the slot of the HPT stator case. It also has two special
alignment pins to align the HPT hanger support to the HPT stator case. Two
tapped storage holes are provided for the alignment pins when they are not being
used. The aft ring is a lighter aluminum ring used to assemble the HPT stage 2
shroud support to the HPT stator case. The G03 version of the tool is similar
to the G02 version, but can also be used on the CF6-80E1 engine.
DIMENSIONS: 46 in. dia x 30 in. (1,168 mm dia x 763 mm).
WEIGHT: 540 lbs (245 kg).
SUPPORTING TOOLS: Crane.
TOOL MAINTENANCE: Apply a light coat of corrosion preventive oil to
treated surfaces when in storage. Load test periodically (see GE
drawing 2C24783 for load test diagram).
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS LIST
GROUP PART NO. NOMENCLATURE QUANTITY SUPPLIER
NUMBER CODE
G03 2C14783P03 Clamp 12
2C14783P04 Ring, forward 1
2C14783P07 Support 8
2C14783P08 Pin, locating 2
2C14783P10 Clamp 3
2C14783P34 Gauge 1
2C14783P36 Segment, Jacking 24
2C14783P37 Ring, Aft 1
20097-12C-40B Screw, Skt HD Cap 48
47311 Hoist, ring 3 F
47312 Hoist, ring 3 F
CL-3-SW Washer, spherical 18 I
CL-5-SW Washer, spherical 48 I
MS15795-814 Washer, flat 3
FOR ALL
2C14783G03
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
GROUP PART NO. NOMENCLATURE QUANTITY SUPPLIER
NUMBER CODE
MS16995-81B Screw, Skt HD Cap 3
MS16995-99B Screw, Skt HD Cap 12
MS16995-111B Screw, Skt HD Cap 8
91251A843 Screw Skt HD Cap ALT
FOR ALL
2C14783G03
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C14783G03
Page 3
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FIXTURE, REMOVE - HPT ROTOR AFT AIR SEALS
2C14784G01
FOR ALL
2C14784G01
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C14784G01
Page 2
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FIXTURE, PULL - HIGH PRESSURE TURBINE ROTOR AFT AIR SEALS
2C14785G01
PURPOSE AND USE: The Pull Fixture is used to remove the aft air seal from
the high pressure turbine (HPT) rotor disk.
DESCRIPTION: The Pull Fixture consists of a guide tube, rest pad, slide clamps,
clamp arms, and support frame. The tool has a black oxide or black phosphate
finish. The G01 version is obsolete and was superseded by 2C14785G02, which has
a modified arm clamp and can be used with the CF6-80E1 engine also.
DIMENSIONS: 16 x 10 in. (406 x 254 mm).
WEIGHT: 15 lbs (7 kg).
SUPPORTING TOOLS: None.
TOOL MAINTENANCE: Apply corrosion preventive oil to all surfaces that
have black oxide or black phosphate coating.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing 2C14785.
FOR ALL
2C14785G01
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C14785G01
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FIXTURE, PULL - HIGH PRESSURE TURBINE ROTOR AFT AIR SEALS
2C14785G02
PURPOSE AND USE: The Pull Fixture is used to remove the aft air seal from
the high pressure turbine (HPT) rotor disk.
DESCRIPTION: The Pull Fixture consists of a guide tube, rest pad, slide clamps,
clamp arms, and support frame. The tool has a black oxide or black phosphate
finish. This tool has a modified arm clamp and is applicable to the CF6-80E1 also.
DIMENSIONS: 16 x 10 in. (406 x 254 mm).
WEIGHT: 15 lbs (7 kg).
SUPPORTING TOOLS: None.
TOOL MAINTENANCE: Apply corrosion preventive oil to all surfaces that
have black oxide or black phosphate coating.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing 2C14785.
FOR ALL
2C14785G02
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C14785G02
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FIXTURE, EXPANSION - INNER OGV SUPPORT
2C14786G01
PURPOSE AND USE: To lift the inner OGV support liner up over the alignment pin
in the stator booster case and to provide a ramp over the pin to prevent other
engine parts from hanging up on the pins during LPC module removal.
DESCRIPTION: The fixture consists of 32 wedges in a series of four sets
with eight wedges on one cord. Each set can be connected to the other
to form a circle around the LPC stator case.
DIMENSIONS: 8 x 8 x 10 in. (203 x 203 x 254 mm).
WEIGHT: 10 lb (4.5 kg).
SUPPORTING TOOLS: None.
TOOL MAINTENANCE: None.
QUANTITY PER OPERATION: One set.
REPLACEMENT PARTS LIST
GROUP PART NO. NOMENCLATURE QUANTITY SUPPLIER
NUMBER CODE
G01 2C14786P02 Wedge Set 4
2C14786P03 Container 1
FOR ALL
2C14786G01
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C14786G01
Page 2
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
ARBOR, CONCENTRICITY FIXTURE - NO. 3 BEARING HOUSING
2C14789P02
FOR ALL
2C14789P02
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C14789P02
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FIXTURE, RUNOUT - NO. 3 BEARING SEALS
2C14790G01
PURPOSE AND USE: To indicate FIR of inboard and outboard No. 3 bearing
air seals for minimum radius calculations.
DESCRIPTION: The fixture consists of a hydraulically actuated arbor,
clamp, dial indicator, and ring gage. The G01 version is obsolete
and was superseded by 2C14790G03.
DIMENSIONS: 8 x 8 x 8 x in. (203 x 203 x 203 mm).
WEIGHT: 25 lbs (11 kg).
SUPPORTING TOOLS: None.
TOOL MAINTENANCE: Coat treated surfaces (black oxide or black phosphate)
with corrosion preventive oil when stored.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS LIST
GROUP PART NO. NOMENCLATURE QUANTITY SUPPLIER
NUMBER CODE
G01 2C14789P01 Arbor, concentricity 1
2C14790P02 Clamp 1
2C14790P03 Thumb screw 2
2C14790P04 Clamp, ball joint 1
2C14790P05 Container 1
FOR ALL
2C14790G01
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C14790G01
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FIXTURE, RUNOUT - NO. 3 BEARING SEALS
2C14790G03
PURPOSE AND USE: To indicate FIR of inboard and outboard No. 3 bearing
air seals for minimum radius calculations.
DESCRIPTION: The fixture consists of a hydraulically actuated arbor,
clamp, dial indicator, and ring gage.
DIMENSIONS: 8 x 8 x 8 x in. (203 x 203 x 203 mm).
WEIGHT: 25 lbs (11 kg).
SUPPORTING TOOLS: None.
TOOL MAINTENANCE: Coat treated surfaces (black oxide or black phosphate)
with corrosion preventive oil when stored.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS LIST
GROUP PART NO. NOMENCLATURE QUANTITY SUPPLIER
NUMBER CODE
G03 2C14789P02 Arbor, concentricity 1
2C14790P02 Clamp 1
2C14790P03 Thumb screw 2
599-7054 Attachment, dovetail 1
2C14790P05 Container 1
FOR ALL
2C14790G03
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C14790G03
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
CLAMP, RETAINING - STAGE 1 SHROUD SUPPORT
2C14791G01
PURPOSE AND USE: To hold the stage 1 high pressure turbine stator shroud support
during transportation from assembly to machining operation.
DESCRIPTION: This fixture consists of a ring with studs that interface with the
forward flange of the HPT stator case. Washers and nuts are supplied. The tool
is made of steel and black oxided for corrosion protection.
DIMENSIONS: 38 in. dia x 1.5 in. (965 mm dia x 38 mm).
WEIGHT: 35 lbs (16 kg).
SUPPORTING TOOLS: None.
TOOL MAINTENANCE: Coat treated surfaces (black oxide or black phosphate)
with corrosion preventive oil.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS LIST
GROUP PART NO. NOMENCLATURE QUANTITY SUPPLIER
NUMBER CODE
G01 2C14791P02 Ring, clamp 1
MS35649-2 Nut, plain 24
MS9321-10 Washer, flat 24
FOR ALL
2C14791G01
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C14791G01
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
ADAPTER, LOCKING - CORE ENGINE
2C14793P01
PURPOSE AND USE: To lock the core engine for maintenance or for engine ferry.
DESCRIPTION: Adapter is a square plate with four holes to attach to the
motoring pad of the accessory gearbox module. The square protrusion prevents
rotation of the gearbox and the core engine.
DIMENSIONS: 3.4 x 2.3 in. (86.4 x 58 mm).
WEIGHT: 2 lb (0.9 kg).
SUPPORTING TOOLS: Used with 2C14794G01.
TOOL MAINTENANCE: Coat black oxide or black phosphate surfaces
with corrosion preventive oil.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: None.
FOR ALL
2C14793P01
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C14793P01
Page 2
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
STRAP, LOCKING - FAN ROTOR
2C14794G01
PURPOSE AND USE: The Locking Strap is used to prevent the fan rotor from
windmilling during engine ferry or maintenance.
DESCRIPTION: The Locking Strap consists of brackets and strap assemblies.
DIMENSIONS: 6 x 10 x 18 in. (152 x 254 x 457 mm).
WEIGHT: 30 lbs (14 kg).
SUPPORTING TOOLS: 2C14793.
TOOL MAINTENANCE: None.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing 2C14794.
FOR ALL
2C14794G01
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C14794G01
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
ADAPTER, LIFT - AFT ENGINE
2C14795G01
PURPOSE AND USE: To lift the engine (Boeing and Airbus only) at the
aft flight mounts while the engine is positioned horizontally in or
out of its shipping container.
DESCRIPTION: The adapter consists of a base and an arm.
DIMENSIONS: 12 x 7 x 13 in. (305 x 178 x 330 mm).
WEIGHT: 50 lbs (22.7 kg).
SUPPORTING TOOLS: Used with 2C14130, 2C14715G01/G02 and two overhead
hoists, 10,000 lbs (4,545 kg) each.
TOOL MAINTENANCE: Lightly coat black oxide or black phosphate surfaces
with corrosion preventive oil.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS LIST
GROUP PART NO. NOMENCLATURE QUANTITY SUPPLIER
NUMBER CODE
G01 2C14795P02 Base 1
2C14795P03 Arm 1
2C14795P04 Pin 1
2C14795P05 Pin 1
2C14795P06 Spacer 1
S-213-.875 6.5 Tons Anchor Shackle 1
FOR ALL
2C14795G01
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C14795G01
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
GAGE, LENGTH - HP TURBINE ROTOR BLADE, STAGE 1
2C14796G01
PURPOSE AND USE: To determine both the relative blade height and the
absolute blade height. This is used for stage 1 blades, part numbers
9374M95G12/G14, which are made of R80 material.
DESCRIPTION: The fixture consists of a base to which is mounted a block
holding a carbide locating pin. The indicator mounted on the block is
calibrated with a set master that is supplied.
DIMENSIONS: 2 x 8 x 5 in. (51 x 203 x 127 mm).
WEIGHT: 10 lbs (4.5 kg) each.
SUPPORTING TOOLS: None.
TOOL MAINTENANCE: Lightly coat black oxide or black phosphate surfaces
with corrosion preventive oil.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: See GE drawing 2C14796.
FOR ALL
2C14796G01
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C14796G01
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
GAGE, LENGTH - HP TURBINE ROTOR BLADE, STAGE 2
2C14796G02
PURPOSE AND USE: To determine both the relative blade height and the
absolute blade height. This is used for stage 2 blades, part numbers
9374M95G12/G14, which are made of R80 material.
DESCRIPTION: The fixture consists of a base to which is mounted a block
holding a carbide locating pin. The indicator mounted on the block is
calibrated with a set master that is supplied.
DIMENSIONS: 2 x 8 x 5 in. (51 x 203 x 127 mm).
WEIGHT: 10 lbs (4.5 kg) each.
SUPPORTING TOOLS: None.
TOOL MAINTENANCE: Lightly coat black oxide or black phosphate surfaces
with corrosion preventive oil.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: See GE drawing 2C14796.
FOR ALL
2C14796G02
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C14796G02
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
GAGE, LENGTH - HP TURBINE ROTOR BLADE, STAGE 2
2C14796G03
PURPOSE AND USE: To determine both the relative blade height and the
absolute blade height. This is used for stage 2 blades, part number
1881M52G01, which are made of DSR142 material.
DESCRIPTION: The fixture consists of a base to which is mounted a block
holding a carbide locating pin. The indicator mounted on the block is
calibrated with a set master that is supplied.
DIMENSIONS: 2 x 8 x 5 in. (51 x 203 x 127 mm).
WEIGHT: 10 lbs (4.5 kg) each.
SUPPORTING TOOLS: None.
TOOL MAINTENANCE: Lightly coat black oxide or black phosphate surfaces
with corrosion preventive oil.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: See GE drawing 2C14796.
FOR ALL
2C14796G03
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C14796G03
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
TOOL, INSTALLATION - LPT BALANCE WEIGHT CLIP
2C14798G01
PURPOSE AND USE: To assist the installation of the low pressure turbine balance
weights during the low pressure turbine balancing procedure.
DESCRIPTION: The tool consists of a claw to hold the clip, a crimp finger to crimp
the tab and a pliers-type mechanism to actuate the crimper finger.
DIMENSIONS: 3 x 12 x 25 in. (76 x 305 x 635 mm).
WEIGHT: 1.5 lb (0.7 kg).
SUPPORTING TOOLS: Used with 2C14963 and 2C14965.
TOOL MAINTENANCE: None.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: See GE drawing 2C14798.
FOR ALL
2C14798G01
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C14798G01
Page 2
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FIXTURE, LIFT AND TURN - ENGINE WITH MID-SHAFT
2C14802G01
PURPOSE AND USE: The Lift and Turn Fixture is used to rotate the engine
vertical/horizontal with the low pressure turbine module removed.
DESCRIPTION: The Lift and Turn Fixture has a lift beam with an adjustable
eye for C.G. adjustments, and lifting cables on each end that attach to a
lifting ring. The primary color of the tool is green.
DIMENSIONS: 39 x 6 in. (991 x 152 mm).
WEIGHT: 150 lb (68 kg).
SUPPORTING TOOLS: Two Hoists, 2C14186.
TOOL MAINTENANCE: Apply corrosion preventive oil to all surfaces that
have black oxide or black phosphate coating.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing 2C14802.
FOR ALL
2C14802G01
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C14802G01
Page 2
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
GAGE, TRAILING EDGE BOW - STAGE 1 HPT ROTOR BLADE
2C14805G01
PURPOSE AND USE: To inspect the trailing edge for distortion or bowing.
DESCRIPTION: The fixture consists of a base, angular pedestal, and gage plate with
pins and locator balls to position the blade. A master is provided for calibration.
DIMENSIONS: 9 x 7 x 6 in. (229 x 178 x 152 mm).
WEIGHT: 15 lb (6.8 kg).
SUPPORTING TOOLS: None.
TOOL MAINTENANCE: Lightly coat black oxide or black phosphate surfaces
with corrosion preventive oil.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS LIST
GROUP PART NO. NOMENCLATURE QUANTITY SUPPLIER
NUMBER CODE
G01 2C14805P02 Plate, Base 1
2C14805P03 Block, Raiser 1
2C14805P04 Plate, Gage 1
2C14805P05 Indicator, Dial 1
2C14805P06 Master, Set 1
AD-87 Collet, Split 1 AV
FOR ALL
2C14805G01
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C14805G01
Page 2
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
SET, RESTRAINING RING - HPT COOLING MANIFOLD
2C14807G01
PURPOSE AND USE: To restrain the flex joint radially outward during
assembly of the HPT cooling manifold.
DESCRIPTION: The fixture consists of a four-piece collar and four hose clamps.
DIMENSIONS: 3.5 in. dia x 2 in. long (89 mm dia x 51 mm).
WEIGHT: 2 lbs (0.9 kg).
SUPPORTING TOOLS: None.
TOOL MAINTENANCE: Lightly coat black oxide or black phosphate surfaces
with corrosion preventive oil.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS LIST
GROUP PART NO. NOMENCLATURE QUANTITY SUPPLIER
NUMBER CODE
G01 2C14807P02 Collar 4
MS35842-14 Clamp, Hose 4
FOR ALL
2C14807G01
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C14807G01
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
COVER, ENGINE - SHIPPING
2C14808P03
PURPOSE AND USE: The Engine Cover is used to protect the engine from contamination
and rain during transport and short-term outdoor storage.
DESCRIPTION: The Engine Cover is made of fabric coated with vinyl or
chloroprene and it is fire retardant, waterproof and resistant to tearing.
The primary color of the tool is blue.
DIMENSIONS: 104 in. dia x 158 in. (2,642 mm dia x 4,013 mm).
WEIGHT: 75 lbs (34 kg).
SUPPORTING TOOLS: AM-1928 or 2C6143.
TOOL MAINTENANCE: None.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing 2C14808.
FOR ALL
2C14808P03
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C14808P03
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
COVER, ENGINE - SHIPPING
2C14808P04
PURPOSE AND USE: The Engine Cover is used to protect the engine from contamination
and rain during transport and short-term outdoor storage.
DESCRIPTION: The Engine Cover is made of fabric coated with vinyl or chloroprene
and it is fire retardant, waterproof and resistant to tearing. The primary color
of the tool is blue. The P04 version is the same as P03 but adds 24 grommets
for improved drainage in the bottom half of the cover.
DIMENSIONS: 104 in. dia x 158 in. (2,642 mm dia x 4,013 mm).
WEIGHT: 75 lbs (34 kg).
SUPPORTING TOOLS: AM-1928 or 2C6143.
TOOL MAINTENANCE: None.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing 2C14808.
FOR ALL
2C14808P04
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C14808P04
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FIXTURE, REMOVAL - STAGE 13 VANE SEGMENTS
2C14809G01
PURPOSE AND USE: The Removal Fixture is used to remove the stage
13 compressor stator vanes.
DESCRIPTION: The Removal Fixture has a base, half ring with studs, swing hammer, and
a clamp assembly. The tool has a black oxide or black phosphate finish.
DIMENSIONS: 24 x 38 x 9 in. (610 x 965 x 229 mm).
WEIGHT: 350 lb (159 kg).
SUPPORTING TOOLS: None.
TOOL MAINTENANCE: Apply corrosion preventive oil to all surfaces that
have black oxide or black phosphate coating.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing 2C14809.
FOR ALL
2C14809G01
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C14809G01
Page 2
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
TOOL, REMOVAL - FUEL MANIFOLD SHROUD
2C14810G01
PURPOSE AND USE: The Removal Tool is used to hold the fuel manifold
shroud in disassembly operations.
DESCRIPTION: The Removal Tool is a pair of pliers with an upper adapter clamp and
a lower clamp/toggle welded assembly. The primary color of the tool is blue.
DIMENSIONS: 7.6 x 3 x 2 in. (193 x 76 x 51 mm).
WEIGHT: 1 lb (0.5 kg).
SUPPORTING TOOLS: None.
TOOL MAINTENANCE: TBD
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing 2C14810.
FOR ALL
2C14810G01
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C14810G01
Page 2
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
PULLER, NO. 6 BEARING PLUG
2C14811G01
FOR ALL
2C14811G01
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C14811G01
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FIXTURE, TORQUE - PLUG ADAPTER
2C14812G01
PURPOSE AND USE: The Torque Fixture is used to hold the engine identification
plug when you torque the adapter and cap.
DESCRIPTION: The Torque Fixture is a restraint plate and two cylindrical
socket adapters with a 150 degree section removed. The tool has a
black oxide or black phosphate finish.
DIMENSIONS: 6 x 2 x 4 in. (152 x 51 x 102 mm).
WEIGHT: 2 lb (1 kg).
SUPPORTING TOOLS: Torque Wrench.
TOOL MAINTENANCE: Apply corrosion preventive oil to all surfaces that
have black oxide or black phosphate coating.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing 2C14812.
FOR ALL
2C14812G01
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C14812G01
Page 2
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
KIT, CLEARANCE GAGE - LOW PRESSURE TURBINE MODULE
2C14813G01
PURPOSE AND USE: The Clearance Gage Kit is used to make a measurement
of the axial dimension between the stage 1 or 5 nozzle outer platform
and the stage 1 or 5 blade outer platform.
DESCRIPTION: The tool has two parts. One part is used for the stage 1
measurement, the other for the stage 5 measurement.
DIMENSIONS: 12 x 8 x 6 in. (305 x 203 x 152 mm).
WEIGHT: 2 lb (1 kg).
SUPPORTING TOOLS: Dial Calipers.
TOOL MAINTENANCE: None.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing 2C14813.
FOR ALL
2C14813G01
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C14813G01
Page 2
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
PROTECTOR, MACHINE SCREW REMOVAL - CDP SEAL
2C14814P01
PURPOSE AND USE: The Machine Screw Removal Protector is used to prevent
damage to the No. 4 bearing rotating air seal during installation
and removal of the machine screws.
DESCRIPTION: The Machine Screw Removal Protector is a urethane ring with
forty-four equally spaced through holes.
DIMENSIONS: 15 x 0.1 in. (381 x 3 mm).
WEIGHT: 0.4 lb (0.2 kg).
SUPPORTING TOOLS: None.
TOOL MAINTENANCE: None.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing 2C14814.
FOR ALL
2C14814P01
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C14814P01
Page 2
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FIXTURE, ASSEMBLY/INSTALL - STAGE 1 HPT SHROUD ASSEMBLY
2C14816P01
PURPOSE AND USE: The Assembly/Install Fixture is used to hold the stage 1 high
pressure turbine (HPT) shrouds when the seals are assembled.
DESCRIPTION: The Assembly/Install Fixture is a single ring with a black oxide or
black phosphate finish. This tool is used with Pre SB 72-0607 configurations only.
DIMENSIONS: 37 x 0.38 in. (940 x 10 mm).
WEIGHT: 8 lbs (4 kg).
SUPPORTING TOOLS: 2C14783.
TOOL MAINTENANCE: Apply corrosion preventive oil to all surfaces that
have black oxide or black phosphate coating.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing 2C14816.
FOR ALL
2C14816P01
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C14816P01
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
DELETED
2C14817G01
PURPOSE AND USE: This tool has been deleted in its entirety.
FOR ALL
2C14817G01
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
GAGE ASSEMBLY, CONCENTRICITY - HOUSING, BEARING NO. 2 - GEARSHAFT, HORIZONTAL -
INLET GEARBOX
2C14817G02
PURPOSE AND USE: The Concentricity Gage Assembly is used to check the minimum
concentricity between the No. 2 bearing housing and the inlet gearbox seal nut.
DESCRIPTION: The Concentricity Gage Assembly has a precision circular plate
with knurled knobs and a locator plate mounted on a handle. The tool has
a black oxide or black phosphate finish.
DIMENSIONS: 16 x 9.5 in. (406 x 241 mm).
WEIGHT: 15 lb (7 kg).
SUPPORTING TOOLS: None.
TOOL MAINTENANCE: Apply corrosion preventive oil to all surfaces that
have black oxide or black phosphate coating.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing 2C14817.
FOR ALL
2C14817G02
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C14817G02
Page 2
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FIXTURE ASSEMBLY, RESTRAINING - HIGH PRESSURE TURBINE NOZZLE SUPPORT - STAGE 1
2C14818G01
PURPOSE AND USE: The Restraining Fixture Assembly is used to hold the high
pressure turbine nozzle (HPTN) support during inspection.
DESCRIPTION: The Restraining Fixture Assembly is a plate with eight spring loaded
clamps along the top. The tool has a black oxide or black phosphate finish.
DIMENSIONS: 18 x 2 in. (457 x 51 mm).
WEIGHT: 60 lb (27 kg).
SUPPORTING TOOLS: None.
TOOL MAINTENANCE: Apply corrosion preventive oil to all surfaces that
have black oxide or black phosphate coating.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing 2C14818.
FOR ALL
2C14818G01
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C14818G01
Page 2
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
KIT ASSEMBLY, COVER - FUEL PUMP AND LINE
2C14819G01
PURPOSE AND USE: The Assembly Kit permits the fuel pump inlet and quick
engine change fuel line outlet to be blocked, or to put oil into the
fuel pump during engine preservation.
DESCRIPTION: The Assembly Kit has two plates each with four attaching bolts.
One plate has a male connector in the center.
DIMENSIONS: 3 x 3 x 3 in. (76 x 76 x 76 mm).
WEIGHT: 2 lb (1 kg).
SUPPORTING TOOLS: None.
TOOL MAINTENANCE: None.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing 2C14819.
FOR ALL
2C14819G01
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C14819G01
Page 2
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
DELETED
2C14821G01
PURPOSE AND USE: This tool has been deleted in its entirety.
Superseded by tool 2C14821G02.
FOR ALL
2C14821G01
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FIXTURE ASSEMBLY, RESTRAIN - HIGH PRESSURE TURBINE ROTOR SPACER IMPELLER
2C14821G02
PURPOSE AND USE: The Restrain Fixture Assembly is used to hold the
high pressure turbine rotor (HPTR) spacer impeller during inspection
of the forward rabbet diameter.
DESCRIPTION: The Restrain Fixture Assembly is a large ring with 20 spring loaded
clamps along the top. The tool has a black oxide or black phosphate finish.
DIMENSIONS: 28 x 4 in. (711 x 102 mm).
WEIGHT: 172 lbs (78 kg).
SUPPORTING TOOLS: None.
TOOL MAINTENANCE: Apply corrosion preventive oil to all surfaces that
have black oxide or black phosphate coating.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing 2C14821.
FOR ALL
2C14821G02
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C14821G02
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FIXTURE, GRIND - HIGH PRESSURE TURBINE, STAGE 2 SHROUDS
2C14822G03
PURPOSE AND USE: This tool is used to measure the axial width of the
low pressure turbine blade retainers.
DESCRIPTION: This tool consists of a frame. The frame is a "U" shaped
tube that has a steel block welded to each end.
DIMENSIONS: 20 x 12 x 6 in. (508 x 205 x 152.4 mm).
WEIGHT: 5 lbs (2 kg).
SUPPORTING TOOLS: Spanner wrench and vernier caliper.
TOOL MAINTENANCE: Apply corrosion preventive oil to all surfaces that
have black oxide or black phosphate.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing 2C14822.
FOR ALL
2C14822G03
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C14822G03
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FIXTURE, GRIND - HIGH PRESSURE TURBINE, STAGE 2 SHROUDS
2C14823G01
PURPOSE AND USE: The Grind Fixture is used to restrain the high pressure turbine
(HPT) shrouds and nozzles as an assembly during grinding operations. It also
provides a means to force fluid through the ports where grinding debris may enter.
DESCRIPTION: The Grind Fixture consists of a base plate, forward and aft restraint
rings, a cylindrical shaped coolant contamination shell, hoses, and a lift
and turn fixture. The primary color of the tool is blue.
DIMENSIONS: 64 x 64 x 40 in. (1626 x 1626 x 1016 mm).
WEIGHT: 3500 lb (1588 kg).
SUPPORTING TOOLS: VTL, Hoist, Pump, and Filtration System.
TOOL MAINTENANCE: Do an inspection and check the calibration of the tool
periodically. Refer to drawing 2C14823.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing 2C14823.
FOR ALL
2C14823G01
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C14823G01
Page 2
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FIXTURE, INSTALLATION/REMOVAL - ROTATING INTERSTAGE SEAL HIGH PRESSURE TURBINE ROTOR
DISK
2C14824G01
PURPOSE AND USE: To install and remove the Rotating Interstage Seal from stage
1 of the High Pressure Rotor Disk on boltless, R88DT rotors. The G01 version
is used with Pre SB 72-1318 Rotating Interstage Seal PN 1778M69P04.
DESCRIPTION: The tool consists of four main parts, a guide tube, clamp, housing, and
the pusher plate. This tool is applicable to CF6-80C2 engine model B8F only.
DIMENSIONS: 32 in. outer dia x 30 in. (812 mm outer dia x 762 mm).
WEIGHT: 300 lbs (136 kg).
SUPPORTING TOOLS: Use with 2C14833G01, 2C14844, Sweeney 8100 and Anchor Plate
Sweeney 23480-4, customer supplied torque wrench.
TOOL MAINTENANCE: Apply corrosion preventive oil to all surfaces
that have black oxide finish.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing 2C14824.
FOR B8F
2C14824G01
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR B8F
2C14824G01
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FIXTURE, INSTALLATION/REMOVAL - ROTATING INTERSTAGE SEAL HIGH PRESSURE TURBINE ROTOR
DISK
2C14824G02
PURPOSE AND USE: To install and remove the Rotating Interstage Seal from stage
1 of the High Pressure Rotor Disk on boltless, R88DT rotors. The G02 version
is used with SB 72-1318 Rotating Interstage Seal PN 1778M69P05.
DESCRIPTION: The tool consists of four main parts, a guide tube, clamp, housing,
and the pusher plate. The G01 had a P02 guide tube, but the G02 has a P21
guide tube with a different length. The G01 also had a P03 clamp, whereas
the G02 has a P22 clamp due to a resigned rotating interstage seal. The G02
also adds three tapped holes to the guide tube to lift the part. This tool
is applicable to CF6-80C2 engine model B8F only.
DIMENSIONS: 32 in. outer dia x 30 in. (812 mm outer dia x 762 mm).
WEIGHT: 300 lbs (136 kg).
SUPPORTING TOOLS: Use with 2C14833G01, 2C14844, Sweeney 8100 and Anchor Plate
Sweeney 23480-4, customer supplied torque wrench.
TOOL MAINTENANCE: Apply corrosion preventive oil to all surfaces
that have black oxide finish.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing 2C14824.
FOR B8F
2C14824G02
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR B8F
2C14824G02
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FIXTURE, INSTALLATION/REMOVAL - ROTATING INTERSTAGE SEAL HIGH PRESSURE TURBINE ROTOR
DISK
2C14824G03
PURPOSE AND USE: To install and remove the Rotating Interstage Seal from stage
1 of the High Pressure Rotor Disk on boltless, R88DT rotors. The G02 version
is used with SB 72-1318 Rotating Interstage Seal PN 1778M69P05.
DESCRIPTION: The tool consists of four main parts, a guide tube, clamp, housing,
and the pusher plate. The G03 uses the P02 guide tube that was used on the
G01, but uses the P22 clamp from the G02. The G03 adds an adapter ring, P23,
to make up for height difference between the P02 and P21 guide tube. The G03
was intended to replace the G02 until the G02 guide tube, P21, was completed and
shipped. This tool is applicable to CF6-80C2 engine model B8F only.
DIMENSIONS: 32 in. outer dia x 30 in. (812 mm outer dia x 762 mm).
WEIGHT: 300 lbs (136 kg).
SUPPORTING TOOLS: Use with 2C14833G01, 2C14844, Sweeney 8100 and Anchor Plate
Sweeney 23480-4, customer supplied torque wrench.
TOOL MAINTENANCE: Apply corrosion preventive oil to all surfaces
that have black oxide finish.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing 2C14824.
FOR B8F
2C14824G03
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR B8F
2C14824G03
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FIXTURE, INSTALLATION/REMOVAL - ROTATING INTERSTAGE SEAL HIGH PRESSURE TURBINE ROTOR
DISK
2C14824G04
PURPOSE AND USE: To install and remove the Rotating Interstage Seal
from stage 1 of the High Pressure Rotor Disk on boltless, R88DT rotors.
The G04 version is an improvement over the G01 and is used with Pre
SB-72-1318 Rotating Interstage Seal PN 1778M69P04.
DESCRIPTION: The tool consists of four main parts, a guide tube, clamp, housing, and
the pusher plate. The G04 uses the P02 guide tube that was on the G01. The G04 can
use either clamp P03 from the G01, or alternate clamp P22 from G02. The G04 adds
a new adapter ring, P24, which has a different thickness that the P23 adapter ring
from G03. This tool is applicable to CF6-80C2 engine model B8F only.
DIMENSIONS: 32 in. outer dia x 30 in. (812 mm outer dia x 762 mm).
WEIGHT: 300 lbs (136 kg).
SUPPORTING TOOLS: Use with 2C14833G01, 2C14844, Sweeney 8100 and Anchor Plate
Sweeney 23480-4, customer supplied torque wrench.
TOOL MAINTENANCE: Apply corrosion preventive oil to all surfaces
that have black oxide finish.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing 2C14824.
FOR B8F
2C14824G04
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR B8F
2C14824G04
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FIXTURE, INSTALLATION/REMOVAL - HIGH PRESSURE TURBINE FRONT ROTATING AIR SEAL
2C14825G03
PURPOSE AND USE: To install and remove the High Pressure Turbine Rotor Front
Seal (FOS) from/to the high pressure turbine rotor stage disk.
DESCRIPTION: This tool consists of two assemblies, the set-up table and the
restraint fixture. There is also a four-piece segmented ring puller that
interfaces with the restraint fixture to deflect the outer ring of the FOS.
This tool updates the G02 with changes necessary for a spring-style alignment
pin, and is used for boltless R88DT high pressure turbine rotors only. This
tool is applicable to CF6-80C2 engine model B8F only.
DIMENSIONS: 28 in. dia x 25 in. (711 mm dia x 635 mm).
WEIGHT: 550 lbs (249.5 kg).
SUPPORTING TOOLS: Used in combination with hand tools, overhead hoist
with minimum capacity of 550 lbs (249.5 kg).
TOOL MAINTENANCE: Apply corrosion preventive oil to all surfaces
that have black oxide finish.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing 2C14825.
FOR B8F
2C14825G03
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR B8F
2C14825G03
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FIXTURE, RESTRAINT – RETAINING RING, STAGE 2 HIGH PRESSURE TURBINE ROTOR
2C14826G02
PURPOSE AND USE: This fixture is used to assemble and disassemble the high
pressure turbine rotor heat shield to the stage 2 disk.
DESCRIPTION: The fixture consists of ten retainers which are threaded rods
with a block with a pin on one end that interfaces with the holes in the tabs
or ring position on the retainer, a plug which fits down into the dovetail
to provided anti-torque, and a restraint for the knurled knob that pulls
the threaded rod radially outward when tightened. The rod has another pin
through the top portion to indicate the position of the hook. This tool
is applicable to CF6-80C2 engine model B8F only.
DIMENSIONS: 4 x 4 x 16 in. (102 x 102 x 406 mm).
WEIGHT: 5 lbs (2.3 kg).
SUPPORTING TOOLS: None.
TOOL MAINTENANCE: Apply corrosion preventive oil to all surfaces
that have black oxide finish.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing 2C14826.
FOR B8F
2C14826G02
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR B8F
2C14826G02
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
ADAPTER SET, PEDESTAL - ENGINE, AFT
2C14827G01
PURPOSE AND USE: The Pedestal Adapter Set is used to support the aft
end of the engine or turbine rear frame during maintenance operations
and/or storage of the engine or subassemblies.
DESCRIPTION: The Pedestal Adapter Set consists of two identical plates.
Each plate has threaded fasteners located on a radius which corresponds
with the holes on the turbine rear frame.
DIMENSIONS: 32.5 x 10 x 1.25 in. (826 x 254 x 32 mm).
WEIGHT: 22 lb (10 kg).
SUPPORTING TOOLS: Overhead Hoist with a capacity of 10000 lb
(22046 kg), 2C6339, 2C14130.
TOOL MAINTENANCE: TBD
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing 2C14827.
FOR ALL
2C14827G01
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C14827G01
Page 2
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FIXTURE, TORQUE - HPT ROTOR BOLTS
2C14829G01
PURPOSE AND USE: This fixture is used to final torque/break loose the nuts
attaching the high pressure turbine rotor for stages 1 and 2 disks.
DESCRIPTION: The tool consists of a “U” shaped spline box wrench with an index pin
at the drive end. The drive end has a female square to engage a torque wrench
or standard square drive tools. Two additional wrenches are provided that have
ratcheting box ends for nut running on/off. A thick ring is provided to allow
the wrench to rotate about a fixed center above the bolt. The aluminum ring is
hard-coat anodized and the wrenches are black-oxided and nylon coated.
DIMENSIONS: 16 in. dia x 3 in. (406 mm dia x 76 mm).
WEIGHT: 15 lbs (6.8 kg).
SUPPORTING TOOLS: 3/8 sq. drive breaker bar, torque wrench, 2C14831, and 2C14845.
TOOL MAINTENANCE: Coat treated surfaces with corrosion preventive oil.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing 2C14829.
FOR B8F
2C14829G01
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR B8F
2C14829G01
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
RETAINER, SLAVE BLADE - STAGE 1 HPT ROTOR
2C14830G01
PURPOSE AND USE: This fixture is used to retain the stage 1 high pressure turbine
blades and to facilitate the exchanging of blades during assembly balancing.
DESCRIPTION: The tool consists of a steel ring with eight quarter-turn, swing clamps
to secure the tool to the disk. Eight equally tapped holes are also provided
to interface with a slide hammer to facilitate tool removal.
DIMENSIONS: 26.3 in. dia x 2.0 in. (668 mm dia x 51 mm).
WEIGHT: 22 lbs (10.0 kg).
SUPPORTING TOOLS: None.
TOOL MAINTENANCE: Coat treated surfaces with corrosion preventive oil.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing 2C14830.
FOR B8F
2C14830G01
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR B8F
2C14830G01
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
NUT PLATE, SET - STAGE 2 HIGH PRESSURE TURBINE
2C14831G01
PURPOSE AND USE: To provide a means to safely attach tools to the high
pressure turbine stage 2 rotor disk aft flange.
DESCRIPTION: The nut plate set consists of two half rings each with
twelve tapped thru holes, bolts and washers. This tool is used for
boltless R88DT High Pressure Rotors only.
DIMENSIONS: 24 x 12 x 6 in. (610 x 305 x 152 mm).
WEIGHT: 10 lbs (4.5 kg).
SUPPORTING TOOLS: This fixture is used in combination with
2C14632, 2C14829G01, and 2C14836.
TOOL MAINTENANCE: Apply corrosion preventive oil to all surfaces
that have black oxide finish.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing 2C14831.
FOR B8F
2C14831G01
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR B8F
2C14831G01
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FIXTURE, SEPARATE/LIFT STAGE 2 HPT ROTOR DISK
2C14832G01
PURPOSE AND USE: This fixture is used to lift or separate the stage 2
high pressure turbine rotor stage 2 disk.
DESCRIPTION: The fixture consists of a pusher plate, puller plate,
tube, cylinder, and hoist ring.
DIMENSIONS: 12 in. dia x 22 in. (305 mm dia x 559 mm).
WEIGHT: 45 lbs (20.4 kg).
SUPPORTING TOOLS: Three-legged sling, hand pump with a pressure capacity of 10,000
psi (689.5 bar) and overhead hoist with a minimum capacity of 2,000 lbs (907.2 kg).
TOOL MAINTENANCE: Coat treated surfaces with corrosion preventive oil.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing 2C14832.
FOR B8F
2C14832G01
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR B8F
2C14832G01
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FIXTURE, CLAMPING - HIGH PRESSURE TURBINE ROTOR ASSY
2C14835G02
FOR B8F
2C14835G02
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR B8F
2C14835G02
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FIXTURE, INSTALLATION/REMOVAL - STAGE 2 AFT BLADE RETAINER
2C14836G02
PURPOSE AND USE: To install and remove the stage 2 aft blade retainer.
DESCRIPTION: The main frame consists of two plates separated by circular tubes.
The large diameter plate has a heel to direct the force to the desired location
on the blade retainer. The smaller diameter has a bolt pattern into which the
cylinder mounts. The cylinder (pump with pressure gage included) rod is attached
to a flanged push/pull cylinder that mates against the aft flange of the stage 2
high pressure turbine disk. Two semi-circular puller ring halves are included, and
are installed over the forward flange of the push/pull cylinder and the lip of the
stage 2 high pressure turbine disk, locking the two together for operation. Also
included are clips for holding the retainer ring in the collapsed position. This
tool is used for boltless R88DT high pressure turbine rotors only.
DIMENSIONS: 27 in. dia x 29 in. (685 mm dia x 736 mm).
WEIGHT: 300 lbs (136 kg).
SUPPORTING TOOLS: 2C14839, overhead hoist.
TOOL MAINTENANCE: Apply corrosion preventive oil to all surfaces
that have black oxide finish.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing 2C15637.
FOR B8F
2C14836G02
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR B8F
2C14836G02
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
RETAINER, SLAVE - STAGE 2 HPT ROTOR BLADES
2C14837G01
PURPOSE AND USE: This fixture is used to retain the stage 2 high pressure turbine
blades and to facilitate the exchanging of blades during assembly balancing.
DESCRIPTION: The tool consists of a steel ring with eight equally spaced,
quarter-turn, swing clamps to secure the tool to the disk. Eight
equally spaced tapped holes are also provided to interface with a slide
hammer to facilitate tool removal.
DIMENSIONS: 24 in. dia x 2 in. (610 mm dia x 51 mm).
WEIGHT: 7 lbs (3.2 kg).
SUPPORTING TOOLS: Balance machine.
TOOL MAINTENANCE: Coat treated surface with corrosion preventive oli.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing 2C14837.
FOR B8F
2C14837G01
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR B8F
2C14837G01
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FIXTURE, INSTALL/REMOVE - HPT ROTOR PRESSURE BALANCE SEAL
2C14838G01
PURPOSE AND USE: This fixture is used to install/remove the high pressure
turbine rotor pressure balance seal to/from the high pressure turbine
rotor stage 1 disk and front rotating air seal.
DESCRIPTION: The fixture includes a functional subassembly consisting of a
disk adapter tube coupled on its outer diameter to a cylinder adapter tube. A
double acting hydraulic cylinder is installed on the cylinder adapter tube. A
lift cap and hoist ring is provided for handling the subassembly. The fixture
also includes an installation adapter and installation adapter ID ring for
installation, twenty alignment pins, and a removal adapter for removal of the
seal. The fixture is made from steel and has a black oxide finish.
DIMENSIONS: 32 x 17 in. dia (813 x 432 mm dia).
WEIGHT: 120 lbs (54.4 kg).
SUPPORTING TOOLS: 2C14048 and overhead hoist with minimum
capacity of 1,000 lbs (454 kg).
TOOL MAINTENANCE: Coat treated surfaces with corrosion preventive oil.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing 2C14838.
FOR B8F
2C14838G01
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR B8F
2C14838G01
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FIXTURE, INSTALL/REMOVE - HPT ROTOR PRESSURE BALANCE SEAL
2C14838G02
PURPOSE AND USE: This fixture is used to install/remove the high pressure
turbine rotor pressure balance seal to/from the high pressure turbine
rotor stage 1 disk and front rotating air seal.
DESCRIPTION: The fixture has an actuation subassembly consisting of a disk
adapter tube coupled on its outer diameter to a cylinder adapter tube. A
double-acting hydraulic cylinder with two female hydraulic couplers is
attached to the cylinder adapter tube. This fixture uses a spacer ring
necessary for SB 72-1061 configurations.
DIMENSIONS: 32 x 17 in. (813 x 432 mm).
WEIGHT: 130 lbs (59.0 kg).
SUPPORTING TOOLS: Overhead hoist with minimum capacity of 1,000 lbs
(454 kg) and hydraulic hand pump.
TOOL MAINTENANCE: Coat treated surfaces with corrosion preventive oil.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing 2C14838.
FOR B8F
2C14838G02
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR B8F
2C14838G02
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
TOOL INSTALLATION/REMOVAL - RETAINING RING, AFT BLADE RETAINER
2C14839G01
PURPOSE AND USE: To install and remove the high pressure turbine
rotor aft retaining ring.
DESCRIPTION: The tool consists of two modified parallel jaw pliers. One set
has replaceable pins, similar to snap-ring pliers, and the other has blocks
welded to the jaw ends. Extra pins are provided. This tool is used for
boltless R88DT high pressure turbine rotors only.
DIMENSIONS: 11 x 10 x 5 in. (279 x 254 x 127 mm).
WEIGHT: 4 lbs (1.8 kg).
SUPPORTING TOOLS: Not required.
TOOL MAINTENANCE: Apply corrosion preventive oil to all surfaces
that have black oxide finish.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing 2C14839.
FOR B8F
2C14839G01
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR B8F
2C14839G01
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
DELETED
2C14840G01
PURPOSE AND USE: This tool has been deleted in its entirety.
Superseded by tool 2C14871G01.
FOR ALL
2C14840G01
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FIXTURE, LIFT/TURN – HPT ROTOR STAGE 1 AND 2 DISK
2C14844G01
PURPOSE AND USE: This fixture is used to lift and turn the stage 1 and stage
2 high pressure turbine disks from forward up to aft up.
DESCRIPTION: The fixture consists of a functionally reversible lift plate with a
centrally located clevis on each side. A lift arm, shackle, and link subassembly
is used for attachment to an overhead hoist. Nut plates for interfacing with
the disks flanges are also included with the lift fixture.
DIMENSIONS: 24.1 x 14.3 x 5.2 in. (612 x 363 x 132 mm).
WEIGHT: 23 lbs (10.4 kg).
SUPPORTING TOOLS: Overhead hoist with minimum capacity of 1,000 lbs (454 kg).
TOOL MAINTENANCE: Coat treated surfaces with corrosion preventive oil.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing 2C14844.
FOR B8F
2C14844G01
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR B8F
2C14844G01
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
PROTECTOR SET - STAGE 1 AND 2 HPT TURBINE ROTOR DISK BORES
2C14845G01
PURPOSE AND USE: This fixture is used to protect the stage 1 and stage 2
high pressure turbine rotor disk bore from damage while the interstage
nuts are being installed and torqued.
DESCRIPTION: This fixture is an assembly that includes a stage 1 protector and a
stage 2 protector. Both protectors are made of urethane durometer 70A.
DIMENSIONS: Stage 1: 6.98-7.01 in. dia (177.3-178.1 mm dia)
Stage 2: 6.975-7.005 in. dia (177.17-177.93 mm dia)
WEIGHT: TBD
SUPPORTING TOOLS: TBD
TOOL MAINTENANCE: None.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing 2C14845.
FOR B8F
2C14845G01
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR B8F
2C14845G01
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FIXTURE, ASSEMBLY/DISASSY – HPT ROTOR
2C14848G01
PURPOSE AND USE: This fixture is used to hold the high pressure turbine
rotor for assembly and disassembly.
DESCRIPTION: This assembly fixture tool consists of a locator riser that
has an inner flange for supporting the high pressure turbine rotor, and
clamp ring with an internal thread for mating with the high pressure turbine
rotor. A base ring supports the assembly, and a center post is mounted to
the base ring through the center of the locator riser.
DIMENSIONS: 22.5 in. dia x 18 in. (572 mm dia x 457 mm).
WEIGHT: 300 lbs (136 kg).
SUPPORTING TOOLS: Three-point chain sling 9429M54P01, 11C3021, and
temperature-resistant gloves.
TOOL MAINTENANCE: Coat treated surfaces with corrosion preventive oil.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing 2C14848.
FOR B8F
2C14848G01
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR B8F
2C14848G01
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FIXTURE, TORQUE - FUEL FILTER
2C14854G02
PURPOSE AND USE: The Torque Fixture is used to torque the fuel filter attachment
nuts to the correct engine manual specification and also remove them.
DESCRIPTION: The Torque Fixture consists of a box style wrench end, a
square drive wrench end, and a curved bar that separates the two ends.
The tool has a black oxide finish.
DIMENSIONS: 0.75 x 2.5 x 7.5 in. (19 x 64 x 191 mm).
WEIGHT: 0.5 lb (0.2 kg).
SUPPORTING TOOLS: None.
TOOL MAINTENANCE: Apply corrosion preventive oil to all surfaces
that have a black oxide finish.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing 2C14854.
FOR ALL
2C14854G02
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C14854G02
Page 2
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FIXTURE, PNEUMATIC DRIVE MOTOR — CORE ENGINE
2C14855G01
PURPOSE AND USE: To provide a means of rotating the high pressure rotor to
facilitate the borescope inspection of the engine.
DESCRIPTION: The fixture consists of a pneumatic drive motor, a motor adapter
fixture which interfaces with the spur gearshaft, a mechanical protractor, and a
pneumatic hand control. The drive motor has a shear pin which will sustain up to
120 lb ft (163 N.m) of torque. The hand control can be adjusted to rotate the core
between 1/15 and 1/5 revolutions per minute (RPM). The protractor indicates the
rotation of the core. A reusable container for storage and transit is supplied with
this fixture. This tool is applicable to CF6-80C2 engine model B6FA only.
DIMENSIONS: 6.7 x 7.0 x 32.0 in. (170 x 178 x 813 mm).
WEIGHT: 60 lbs (27 kg).
SUPPORTING TOOLS: Used with a motor-adapter.
TOOL MAINTENANCE: None.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing 2C14855.
FOR B6FA
2C14855G01
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR B6FA
2C14855G01
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FIXTURE, PNEUMATIC DRIVE MOTOR — CORE ENGINE
2C14855G02
PURPOSE AND USE: To provide a means of rotating the high pressure rotor to
facilitate the borescope inspection of the engine.
DESCRIPTION: The fixture consists of a pneumatic drive motor, a motor adapter
fixture which interfaces with the spur gearshaft, a mechanical protractor, and a
pneumatic foot tool. The drive motor has a shear pin which will sustain up to 120
lb ft (163 N.m) of torque. The foot control can be adjusted to rotate the core
between 1/15 and 1/5 revolutions per minute (RPM). The protractor indicates the
rotation of the core. A reusable container for storage and transit is supplied with
this fixture. This tool is applicable to CF6-80C2 engine model B6FA only.
DIMENSIONS: 6.7 x 7.0 x 32.0 in. (170 x 178 x 813 mm).
WEIGHT: 60 lbs (27 kg).
SUPPORTING TOOLS: 9470M32P01.
TOOL MAINTENANCE: None.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing 2C14855.
FOR B6FA
2C14855G02
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR B6FA
2C14855G02
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
ADAPTER SET, SPANNER - AIRTUBE NUTS
2C14856G01
NOTE: This tool supersedes the spanner adapter set, 2C6352G07, for use with
reinforced tube end fittings introduced by SB 75-0040, SB 75-0072, SB 75-0077
thru SB 75-0079, SB 75-0081 thru SB 75-0089, and SB 75-0091.
FOR ALL
2C14856G01
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C14856G01
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FIXTURE, INSTALL — HPC BUMPER BEARING
2C14858G01
PURPOSE AND USE: This fixture is used to set the depth of installation of
the stage 10-14 spool/shaft bumper bearing.
DESCRIPTION: The fixture is an expandable finger design with a plunger that forces
the finger out against the bumper bearing that holds it to the tool. This tool is
used with engines that use a stage 10-14 spool shaft (SB 72-0954) only.
DIMENSIONS: 8 x 8 x 24 in. (203 x 203 x 610 mm).
WEIGHT: 8 lbs (3.6 kg).
SUPPORTING TOOLS: Dry ice.
TOOL MAINTENANCE: Coat treated surfaces with corrosion preventive oil.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing 2C14858.
FOR ALL
2C14858G01
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C14858G01
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
PULLER, MANIFOLD - COMPRESSOR ROTOR, STAGE 10–14 SPOOL
2C14859G02
PURPOSE AND USE: To remove the manifold from the inner diameter of the
compressor rotor, stages 10-14 spool/aft shaft.
DESCRIPTION: This tool consists of a housing, arms, arm guide,
shaft, and clevis brackets.
DIMENSIONS: 7.25 in. dia x 20 in. long (184.2 mm dia x 508 mm long).
WEIGHT: 65 lbs (29.5 kg).
SUPPORTING TOOLS: This tool is used with 10,000 psi (68,948 kPa) hydraulic
pump, overhead hoist and hand tools.
TOOL MAINTENANCE: Apply corrosion preventive oil to all surfaces
that have black oxide finish.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing 2C14859.
FOR ALL
2C14859G02
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C14859G02
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FIXTURE, CHILL — HIGH PRESSURE TURBINE STAGE 2 DISK, FORWARD
2C14861P01
PURPOSE AND USE: This fixture is used to keep dry ice on the high pressure turbine
impeller spacer inner flange so the stage 2 disk face is not chilled.
DESCRIPTION: The fixture consists of an aluminum cylinder coated with
plastisol that creates a cavity on the top of the impeller into which
dry ice is placed to cool the impeller.
DIMENSIONS: 11.25 in. dia x 2 in. (286 mm dia x 51 mm).
WEIGHT: 2 lbs (0.9 kg).
SUPPORTING TOOLS: This fixture is used with dry ice.
TOOL MAINTENANCE: None.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing 2C14861.
FOR ALL
2C14861P01
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C14861P01
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
TOOL SET, BREAKING, TORQUE - COMPRESSOR STATOR VANE RETAINING NUT
2C14865G01
PURPOSE AND USE: This fixture is used to break the torque of the compressor
stator vane actuation arm retaining nuts.
DESCRIPTION: There are three torque adapters in the fixture set. The P02
is for the IGV, the P03 is for stages 1 and 2 vanes, and the P04 is for
stages 3 and 4 vanes. Each adapter consists of a socket (12 point) in a
socket with short lever arms attached to each. This is applicable to SB
72-0475, Phase II Aero, FADEC engines only.
DIMENSIONS: 2 x 4 x 6 in. (51 x 102 x 152 mm).
WEIGHT: 3 lbs (1.4 kg).
SUPPORTING TOOLS: Pliers.
TOOL MAINTENANCE: Coat treated surfaces with corrosion preventive oil.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing 2C14865.
FOR ALL
2C14865G01
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C14865G01
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
HOLDER SET - VARIABLE STATOR VANES
2C14866G02
PURPOSE AND USE: This fixture is used to hold multiple vanes when removing
or installing the vane stem nuts.
DESCRIPTION: The fixture set consists of seven phenolic half rings (for stages
IGV through 6) with a series of slots cut into the face to fit over the trailing
edges of the airfoils. This tool supersedes 2C6172G02.
DIMENSIONS: 40 x 20 x 15 in. (1016 x 508 x 381 mm).
WEIGHT: 35 lbs (16 kg).
SUPPORTING TOOLS: Used with 2C6018, 2C6964, 2C6965, 2C14865, and hand tools.
TOOL MAINTENANCE: Not required.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing 2C14866.
FOR ALL
2C14866G02
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C14866G02
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
GAGE, TRAILING EDGE THICKNESS — HPC AIRFOILS
2C14867P01
PURPOSE AND USE: This fixture is used as go/no-go gauge for high pressure
compressor airfoil trailing edge thickness inspection.
DESCRIPTION: The tool consists of a tool steel plate with fifteen notches
terminating in 0.186 diameter holes. The tool has a black oxide finish.
DIMENSIONS: 3 x 3 x 0.006 in. (76 x 76 x 0.15 mm).
WEIGHT: 0.25 lb (0.113 kg).
SUPPORTING TOOLS: None.
TOOL MAINTENANCE: Coat treated surfaces with corrosion preventive oil.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing 2C14867.
FOR ALL
2C14867P01
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C14867P01
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
PUSHER - HIGH PRESSURE TURBINE ROTOR/DUMMY COMPRESSOR ROTOR
2C14869G01
PURPOSE AND USE: This fixture is used to push the high pressure turbine
dummy shaft from the stage 1 disk.
DESCRIPTION: The tool consists of a plate that is threaded at the center
for a hydraulic cylinder. It has a bolt circle to interface with the aft
flange of the stage 2 high pressure turbine disk.
DIMENSIONS: 12 in. dia x 30 in. (305 mm dia x 762 mm).
WEIGHT: 35 lbs (16 kg).
SUPPORTING TOOLS: Hydraulic source with 10,000 psi (68,948 kPa) maximum.
TOOL MAINTENANCE: Apply corrosion preventive oil to all surfaces
that have black oxide finish.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing 2C14869.
FOR ALL
2C14869G01
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C14869G01
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
GAGE, ADJUSTMENT — WEAR BUTTON — COMPRESSOR ACTUATOR RINGS
2C14870G01
PURPOSE AND USE: This tool is used to set actuation ring wear button depth.
DESCRIPTION: The tool consists of three “C” shaped tool steel gages. The
tools have a black oxide finish. A container is provided.
DIMENSIONS: 8.5 x 6.5 x 3.2 in. (216 x 165 x 81 mm).
WEIGHT: 2 lbs (0.91 kg).
SUPPORTING TOOLS: Normal hand tools.
TOOL MAINTENANCE: Coat treated surfaces with corrosion preventive oil.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing 2C14870.
FOR ALL
2C14870G01
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C14870G01
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FIXTURE, INSTALL/REMOVE - MANIFOLD, NO. 1 BEARING
2C14871G01
PURPOSE AND USE: This tool is used to install or remove the No. 1 bearing
oil manifold from the stage 1 disk/forward fan shaft bore.
DESCRIPTION: This tool consists of two circular plates attached by a threaded rod.
It is used with Pre SB 72-1047 fan disks and supersedes 2C14840G01.
DIMENSIONS: 14 in. dia x 14 in. (356 mm dia x 356 mm).
WEIGHT: 15 lbs (7 kg).
SUPPORTING TOOLS: Not required.
TOOL MAINTENANCE: Apply corrosion preventive oil to all surfaces that
have black oxide or black phosphate coating.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing 2C14871.
FOR ALL
2C14871G01
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C14871G01
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FIXTURE, INSTALL/REMOVE - MANIFOLD, NO. 1 BEARING
2C14871G03
PURPOSE AND USE: This tool is used to install or remove the No. 1 bearing
oil manifold from the stage 1 disk/forward fan shaft bore.
DESCRIPTION: This tool consists of two circular plates attached by a
threaded rod. The G03 version of this tool uses taller block clamps
than G01, for POST SB 72-1047 fan disks.
DIMENSIONS: 14 in. dia x 14 in. (356 mm dia x 356 mm).
WEIGHT: 15 lbs (7 kg).
SUPPORTING TOOLS: Not required.
TOOL MAINTENANCE: Apply corrosion preventive oil to all surfaces that
have black oxide or black phosphate coating.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing 2C14871.
FOR ALL
2C14871G03
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C14871G03
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
TOOL SET, NUT INSTALL/REMOVE - COMPRESSOR ROTOR STAGES 9 AND 10
2C14873G02
PURPOSE AND USE: This tool is used to install, torque and remove the
compressor rotor stage 9 and 10 nuts.
DESCRIPTION: The tool set consists of a nut-starter (9448M66), a ratcheting
box wrench to run the nuts on/off, a "click" type torque wrench, a torque
adapter for nut removal, a tool for the installation of the "D" head bolts
into the disk, an adapter, and a container for all items.
DIMENSIONS: 13 x 13 x 6 in. (330 x 330 x 152 mm).
WEIGHT: 5 lbs (2.3 kg).
SUPPORTING TOOLS: Used with standard hand tools.
TOOL MAINTENANCE: Apply corrosion preventive oil to all surfaces
that have black oxide finish.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing 2C14873.
FOR ALL
2C14873G02
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C14873G02
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
PROTECTOR — COMPRESSOR REAR FRAME OUTER AFT FLANGE
2C14875G01
PURPOSE AND USE: This fixture is used to prevent foreign objects from entering
the core assembly during vertical assembly.
DESCRIPTION: The protector is a red ABS plastic "hat shaped" circular cover
with three nylon cords that serve as handles. The handles are located along
the horizontal center line near each side and at the center.
DIMENSIONS: 40 in. dia x 6 in. (1016 mm dia x 152 mm).
WEIGHT: 8 lbs (4 kg).
SUPPORTING TOOLS: None.
TOOL MAINTENANCE: None.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing 2C14875.
FOR ALL
2C14875G01
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C14875G01
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FIXTURE, LIFT COMPRESSOR ROTOR SPOOLS
2C14878G01
PURPOSE AND USE: This fixture is used to lift vertically the stage 3 thru 9
spools during assembly/disassembly of the compressor rotor.
DESCRIPTION: The fixture consists of two blue-painted rectangular steel tubes with a
circular rod welded between them at each end and a "U" shaped circular rod welded
between at the midpoint. The "U" shaped circular rod is used to attach a lifting
device. At each end, a shoe is attached with a hand knob. Also, the rectangular
tube has markings where the shoes are attached and used for lifting.
DIMENSIONS: 24 x 6 x 4 in. (610 x 152 x 102 mm).
WEIGHT: 25 lbs (11 kg).
SUPPORTING TOOLS: Used with an overhead hoist.
TOOL MAINTENANCE: Apply corrosion preventive oil to all surfaces
that have black oxide finish.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing 2C14878.
FOR ALL
2C14878G01
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C14878G01
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
PROTECTOR SET, INSTALL/REMOVE - HPT ROTOR RING
2C14879G01
PURPOSE AND USE: This fixture is used to protect the disk bore when
removing or installing the disk ring.
DESCRIPTION: The fixture includes a center bore protector, a cone bore protector,
and a pick that wraps around the stage 1 HPT rotor disk ring.
DIMENSIONS: TBD.
WEIGHT: TBD.
SUPPORTING TOOLS: None.
TOOL MAINTENANCE: Coat treated surfaces with corrosion preventive oil.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing 2C14879.
FOR ALL
2C14879G01
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C14879G01
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
PULLER, NO. 6 BEARING OUTER RACE
2C14883G01
PURPOSE AND USE: This tool is used to remove No. 6 bearing outer race
from the turbine rear frame sump housing.
DESCRIPTION: The puller consists of a circular puller plate attached to a
circular pusher plate by a hydraulic cylinder. This tool supersedes the
obsolete No. 6 bearing outer race puller, 2C14700G01.
DIMENSIONS: 12 in. dia x 18 in. (305 mm dia x 457 mm).
WEIGHT: 35 lbs (16 kg).
SUPPORTING TOOLS: Hydraulic hand pump and over head hoist.
TOOL MAINTENANCE: Coat treated surfaces with corrosion preventive oil.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing 2C14883.
FOR ALL
2C14883G01
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C14883G01
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
GAUGE, DIAMETER — HPT ROTOR DISK, STAGE 1
2C14885G01
PURPOSE AND USE: The gauge and master are used to check the diameter of the
transition radius between the disk and the shaft portion of disk.
DESCRIPTION: The gage consists of a beam-type aluminum frame to which is attached
two pivoting arms. One pivoting arm is fixed to the frame and the other is
attached to a slide. A collet-mounted dial indicator monitors the slide movement
and allows diametral measurement to the provided master.
DIMENSIONS: 24 x 21 x 9 in. (610 x 533 x 229 mm).
WEIGHT: 20 lbs (9.1 kg).
SUPPORTING TOOLS: None.
TOOL MAINTENANCE: Coat treated surfaces with corrosion preventive oil.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing 2C14885.
FOR ALL
2C14885G01
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C14885G01
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FIXTURE, PROTECTOR, STAGE 1 FAN DISK BORE
2C14890G01
PURPOSE AND USE: This tool is used to protect the fan disk bore.
DESCRIPTION: The protector is a U-shaped ring with two flanges pointed
radially outward. Material is urethane rubber. This fixture is for Post SB
72-1047 disks. For Pre SB 72-1047 disks, use 2C6075.
DIMENSIONS: 13.50 in. dia x 3.62 in. (342.9 mm dia x 91.9 mm).
WEIGHT: 1 lb (0.4 kg).
SUPPORTING TOOLS: Not required.
TOOL MAINTENANCE: Not required.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing 2C14890.
FOR ALL
2C14890G01
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C14890G01
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
COVER, SHIPPING — CF6–80C2 ENGINE (C5)
2C14896P01
PURPOSE AND USE: This fixture is used to provide engine protection from dirt,
water and other contaminants during engine shipment.
DESCRIPTION: The cover is constructed of vinyl or chloroprene coated fabric
containing evenly dispersed fire retardant. The cover is waterproof under normal
rain conditions, flexible at high and low temperatures, and is resistant to
tearing. This fixture is applicable to CF6-80C2 L1F engines only.
DIMENSIONS: N/A.
WEIGHT: 125 lbs (57 kg).
SUPPORTING TOOLS: This fixture is used with two overhead cranes and AGSE-E128-G01/2.
TOOL MAINTENANCE: None.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing 2C14896.
FOR CF6-80C2L1F
2C14896P01
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR CF6-80C2L1F
2C14896P01
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
TOOL SET, RUN ON/OFF — STAGE 1 FAN DISK NUT
2C14897G01
PURPOSE AND USE: This tool is used to run on/off the stage 1 fan disk nuts.
DESCRIPTION: The tool set consists of a drive socket and container.
DIMENSIONS: 1.3 in. dia x 9.00 in. (33 mm dia x 228.6 mm)
WEIGHT: TBD.
SUPPORTING TOOLS: 2C14890.
TOOL MAINTENANCE: Coat treated surfaces with corrosion preventive oil.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing 2C14897.
FOR ALL
2C14897G01
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C14897G01
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
ADAPTER, BALANCE - STAGE 2 COMPRESSOR DRIVE AND BLADES
2C14900G01
PURPOSE AND USE: To provide a means to static balance the stage 2 disk with
blades prior to assembly in the compressor rotor.
DESCRIPTION: Consists of a hardened plate with a rabbet fit for the
balance machine and a rabbet for the aft side of the stage 2 disk, and
assorted screws and nuts for assembly.
DIMENSIONS: 14 in. dia x 1 in. (356 mm dia x 25 mm).
WEIGHT: 24 lb (11 kg).
SUPPORTING TOOLS: Vertical Balance Machine.
TOOL MAINTENANCE: Coat treated surfaces (black oxide or black phosphate)
with corrosion preventive light oil when stored.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS LIST
GROUP PART NO. NOMENCLATURE QUANTITY SUPPLIER
NUMBER CODE
G01 2C14900P02 Plate 1
2C14900P03 Ring 1
CS-32 Setscrew 3 M
FOR ALL
2C14900G01
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C14900G01
Page 2
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
ADAPTER, BALANCE - STAGE 1 COMPRESSOR DISK AND BLADES
2C14901G01
PURPOSE AND USE: To provide a means to static balance the stage 1 disk with
blades prior to assembly in the compressor rotor.
DESCRIPTION: Consists of a hardened plate with a rabbet fit for the balance machine
and stage 1 disk flange, and assorted screws and nuts for assembly.
DIMENSIONS: 13 in dia x 1 in. (330 mm dia x 25 mm).
WEIGHT: 21 lb (10 kg).
SUPPORTING TOOLS: Vertical Balance Machine.
TOOL MAINTENANCE: Coat treated surfaces (black oxide or black phosphate)
with corrosion preventive light oil when stored.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS LIST
GROUP PART NO. NOMENCLATURE QUANTITY SUPPLIER
NUMBER CODE
G01 2C14901P02 Plate 1
2C14901P03 Ring 1
CS-32 Setscrew 3 M
FOR ALL
2C14901G01
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C14901G01
Page 2
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
DELETED
2C14902G01
PURPOSE AND USE: This tool has been deleted in its entirety.
Superseded by tool 2C14902G03.
FOR ALL
2C14902G01
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
STAND, BALANCE BUILD UP - LOW PRESSURE TURBINE MODULE
2C14902G03
PURPOSE AND USE: The balance build up stand is used to support the
balance arbor vertically during assembly of the low pressure turbine
(LPT) module to the balance arbor.
DESCRIPTION: The balance build up stand consists of a square steel frame
on four swivel casters with two floor locks, three arbor supports, and
a worm gear actuator on the frame.
DIMENSIONS: 48 x 48 x 28 in. (1,219 x 1,219 x 711 mm).
WEIGHT: 500 lbs (227 kg).
SUPPORTING TOOLS: 2C14912.
TOOL MAINTENANCE: Apply corrosion preventive oil to all surfaces that
have black oxide or black phosphate coating.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing 2C14902.
FOR ALL
2C14902G03
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C14902G03
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
ADAPTER, BALANCE - STAGE 3-9 AFT AND STAGE 11-14 FORWARD
2C14903G01
PURPOSE AND USE: To support the aft end of the stage 3-9 spool or the
forward end of the stage 11-14 spool.
DESCRIPTION: Consists of a hardened arbor with a 7.166 inch (182.02 mm)
journal and a 273/3 U-joint driver.
DIMENSIONS: 22 in. dia x 7 in. (560 mm dia x 180 mm).
WEIGHT: 53 lb (24 kg).
SUPPORTING TOOLS: Fixtures - 2C14907G01 or 2C14908G01.
TOOL MAINTENANCE: Coat treated surfaces (black oxide or black phosphate)
with corrosion preventive light oil when stored.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS LIST
GROUP PART NO. NOMENCLATURE QUANTITY SUPPLIER
NUMBER CODE
G01 2C14903P02 Adapter 1
CS-30 Setscrew 3 M
FOR ALL
2C14903G01
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C14903G01
Page 2
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
ADAPTER, BALANCE - STAGE 10 DISK AND BLADES
2C14905G01
FOR ALL
2C14905G01
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C14905G01
Page 2
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
PULLER, DRIVE ADAPTERS - ROTOR BALANCING
2C14906G01
PURPOSE AND USE: To provide a means to break the interference fit between the
drive adapters and the engine part or other adapters.
DESCRIPTION: Consists of an automotive type slide hammer with various
adapters for different size drive.
DIMENSIONS: 8 in. dia x 20 in. (203 mm dia x 510 mm).
WEIGHT: 10 lb (4.5 kg).
SUPPORTING TOOLS: Adapters - 2C14906P02, 2C14906P05.
TOOL MAINTENANCE: Coat treated surfaces (black oxide or black phosphate)
with corrosion preventive light oil when stored.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS LIST
GROUP PART NO. NOMENCLATURE QUANTITY SUPPLIER
NUMBER CODE
G01 2C14906P02 Plate 1
2C14906P05 Plate 1
2C14906P07 Plate 1
PS943R Slide Hammer 1 DE
FOR ALL
2C14906G01
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C14906G01
Page 2
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
ADAPTER, BALANCE - STAGE 3-9 COMPRESSOR ROTOR SPOOL - FORWARD
2C14907G01
PURPOSE AND USE: To provide support for the forward end of the stage 3-9
compressor rotor spool during dynamic balance.
DESCRIPTION: Consists of a hardened arbor with a 7.166 in. (182.02 mm) journal and
a 273/3 U-joint rabbet. The arbor mates with the forward flange of the spool.
DIMENSIONS: 13 in. dia x 5 in. (330 mm dia x 127 mm).
WEIGHT: 27 lb (12 kg).
SUPPORTING TOOLS: Adapters - 2C14903G01.
TOOL MAINTENANCE: Coat treated surfaces (black oxide or black phosphate)
with corrosion preventive light oil when stored.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS LIST
GROUP PART NO. NOMENCLATURE QUANTITY SUPPLIER
NUMBER CODE
G01 2C14907P02 Adapter 1
CS-30 Setscrew 3 M
FOR ALL
2C14907G01
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C14907G01
Page 2
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
ADAPTER SET, DRIVE - HIGH PRESSURE COMPRESSOR ROTOR BALANCING
2C14908G02
PURPOSE AND USE: To provide slave races to protect the bearing journals and an
adapter to connect the high pressure compressor rotor to the balance machine.
DESCRIPTION: Consists of a hardened slave races with identical O.D. and a hardened
drive adapter which locates on the 66 tooth spline on the rear shaft.
DIMENSIONS: 9 in. dia x 9 in. (229 mm dia x 229 mm).
WEIGHT: 35 lbs (16 kg).
SUPPORTING TOOLS: Bearing Puller - 2C6815G01; Adapters - 2C14903G01 and 2C14906G01.
TOOL MAINTENANCE: Coat treated surfaces (black oxide or black phosphate)
with corrosion preventive light oil when stored.
QUANTITY PER OPERATION: One.
NOTE: Shop must check with manufacturer of shop's balance machine to make
sure of compatibility with this tooling.
REPLACEMENT PARTS LIST
GROUP PART NO. NOMENCLATURE QUANTITY SUPPLIER
NUMBER CODE
G02 2C14743P02 Dummy Bearing Race 1
2C14908P03 Dummy Race No. 3 1
2C14908P04 Drive Ring 1
2C14908P05 Drive Coupling 1
2C14908P06 Wrench 1
2C14908P07 Nut 1
2C14908P08 Spline Drive 3
2C14908P16 Dummy Nut 1
FOR ALL
2C14908G02
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C14908G02
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
SUPPORT, BALANCE - BUILD UP - COMPRESSOR SPOOLS
2C14909G01
FOR ALL
2C14909G01
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C14909G01
Page 2
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
SHROUD, BALANCE - HPTR OR 11-14 COMPRESSOR SPOOL
2C14914G01
PURPOSE AND USE: To provide an enclosure for the high pressure turbine rotor or
11-14 compressor spool during balance to protect the operator.
DESCRIPTION: Consists of a clam shell cover supported by four adjustable
legs. The primary color of the tool is blue.
DIMENSIONS: 51 x 38 x 12 in. (1,295 x 965 x 305 mm).
WEIGHT: 100 lbs (45 kg).
SUPPORTING TOOLS: Horizontal Balance Machine.
TOOL MAINTENANCE: Coat treated surfaces (black oxide or black phosphate)
with corrosion preventive light oil when stored.
QUANTITY PER OPERATION: One.
NOTE: Shop must check with manufacturer of shop's balance machine to make
sure of compatibility with this tooling.
REPLACEMENT PARTS LIST
GROUP PART NO. NOMENCLATURE QUANTITY SUPPLIER
NUMBER CODE
G01 2C14914P02 Shroud 1
2C14914P03 Foot 2
FOR ALL
2C14914G01
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C14914G01
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
SHROUD, BALANCE - COMPRESSOR ROTOR
2C14915G01
PURPOSE AND USE: To provide an enclosure for the compressor rotor during
balance to protect the operator.
DESCRIPTION: Consists of a clam shell cover supported by four adjustable
legs. The cover is opened and closed by an air cylinder. The
primary color of the tool is blue.
DIMENSIONS: 32 x 50 x 40 in. (813 x 1,270 x 1,016 mm).
WEIGHT: 200 lbs (91 kg).
SUPPORTING TOOLS: HL5 Balance Machine.
TOOL MAINTENANCE: Coat treated surfaces (black oxide or black phosphate)
with corrosion preventive light oil when stored.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS LIST
GROUP PART NO. NOMENCLATURE QUANTITY SUPPLIER
NUMBER CODE
G01 2C14915P02 Shroud-Lower Half 1
2C14915P03 Shroud-Upper Half 1
2C14915P04 Foot 4
2C14915P05 Pin 1
2C14915P061 Hinge Rod 1
1525-4 Hose (0.25 I.D.) AR DF
4504 Muffler Speed Control 1 DG
824H Valve, 4 - Way 1 DG
D-231-3 Piston Rod and Nut 1 CR
Clevis
D-620 Pivot Bracket 1 CR
4738-4-4 Hose Connection 4 DF
3112-DXP Air Cylinder Pivot 1 CR
Mount
TB-1225 Thrust Bearing AR E
FOR ALL
2C14915G01
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C14915G01
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
SHROUD, BALANCE - STAGE 3-9 COMPRESSOR SPOOL
2C14916G01
PURPOSE AND USE: To provide an enclosure for the stage 3-9 compressor
spool during balance to protect the operator.
DESCRIPTION: Consists of a clam shell cover which is supported by four
adjustable legs. The primary color of the tool is blue.
DIMENSIONS: 50 x 36 x 40 in. (1,270 x 914 x 1,016 mm).
WEIGHT: 150 lbs (68 kg).
SUPPORTING TOOLS: Schenck HL5 Balance Machine.
TOOL MAINTENANCE: None required.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS LIST
GROUP PART NO. NOMENCLATURE QUANTITY SUPPLIER
NUMBER CODE
G01 2C14916P02 Shroud 1
2C14916P03 Foot 4
FOR ALL
2C14916G01
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C14916G01
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
SHROUD, BALANCE - FAN ROTOR
2C14917G01
FOR ALL
2C14917G01
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
GROUP PART NO. NOMENCLATURE QUANTITY SUPPLIER
NUMBER CODE
3250C Flow Control 4 DG
1525-8 Hose AR DF
2090-8-8S Internal Tee 2 DF
2021-8-BS Male Connector 4 DF
4738-8-8S Fitting 4 DF
2089-8-8S Street Elbow 6 DF
3464XG Regulator 1 DG
4797-85 Fitting 4 DF
FOR ALL
2C14917G01
Page 2
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C14917G01
Page 3
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
TOOL SET, BALANCE - HIGH PRESSURE TURBINE ROTOR
2C14920G02
PURPOSE AND USE: The Balance Tool Set is used to provide slave blade
retainers to reposition blades without clamping the rotor joints during
balance of the high pressure turbine (HPT) rotor.
DESCRIPTION: The Balance Tool Set consists of two steel rings and 175 special
washers. The tool has a black oxide or black phosphate finish.
DIMENSIONS: 27 x 3 in. (686 x 76 mm).
WEIGHT: 75 lbs (34 kg).
SUPPORTING TOOLS: Balance equipment.
TOOL MAINTENANCE: Apply corrosion preventive oil to all surfaces that
have black oxide or black phosphate coating.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing 2C14920.
FOR ALL
2C14920G02
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C14920G02
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
ADAPTER, BALANCE - LOW PRESSURE TURBINE ROTATING SEAL
2C14921G01
PURPOSE AND USE: The balance adapter is used to balance the low pressure
turbine (LPT) rotating seals.
DESCRIPTION: The balance adapter consists of an adapter, set screws, and socket
head cap screws. The tool has a black oxide or black phosphate finish.
DIMENSIONS: 13.5 x 2.5 in. (343 mm x 64 mm).
WEIGHT: 12 lbs (5 kg).
SUPPORTING TOOLS: Balance Machine.
TOOL MAINTENANCE: Apply corrosion preventive oil to all surfaces that
have black oxide or black phosphate coating.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing 2C14921.
NOTE: Shop must check with manufacturer of shop's balance machine to make
sure of compatibility with this tooling.
FOR ALL
2C14921G01
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C14921G01
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
ADAPTER, BALANCE - LOW PRESSURE TURBINE ROTATING SEAL
2C14921G02
PURPOSE AND USE: The balance adapter is used to balance the low pressure
turbine (LPT) rotating seals.
DESCRIPTION: The balance adapter consists of an adapter, set screws, and socket
head cap screws. The tool has a black oxide or black phosphate finish. The G02
version of 2C14921 does not use the P03 adapter. Therefore, it requires fewer
set screws for attachment to the LPT rotating seals than the G01.
DIMENSIONS: 13.5 x 2.5 in. (343 mm x 64 mm).
WEIGHT: 12 lbs (5 kg).
SUPPORTING TOOLS: Balance Machine.
TOOL MAINTENANCE: Apply corrosion preventive oil to all surfaces that
have black oxide or black phosphate coating.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing 2C14921.
NOTE: This tool does not use the P03 adapter and thus requires fewer set screws
than the G01 for attaching the tool to the LPT rotating seals.
FOR ALL
2C14921G02
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C14921G02
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
ADAPTER, BALANCE - LPT MODULE
2C14922G01
PURPOSE AND USE: To support the LP turbine case and rotor during
dynamic balance of the rotor.
DESCRIPTION: The adapter mates with a balance build stand (2C14902) so that the
adapter and LP Turbine can be assembled. The adapter consists of forward and
rear strongbacks, forward drive arbor, forward and aft bearings, and associated
special tooling. The adapter is designed to be used with a balance machine
that has 13.00 inch (330.2 mm) diameter work supports.
DIMENSIONS: 55 in. dia x 53 in. (1,397 mm dia x 1,346 mm).
WEIGHT: 900 lbs (408 kg).
SUPPORTING TOOLS: None.
TOOL MAINTENANCE: Load test periodically (see GE drawing 2C14922 for
load test diagram and applicable NOTE).
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: This fixture has an extensive parts list that will be of
little value without the drawing. Refer to GE Drawing 2C14922.
FOR ALL
2C14922G01
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C14922G01
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
ADAPTER SET, BALANCE - LPT ROTOR, STAGES 1-5
2C14923G01
PURPOSE AND USE: To mount various bladed low pressure turbine disks on a
balancing machine for force balance of the disk.
DESCRIPTION: The tools consists of three balanced tool steel plates. A rabbet plate
attaches to the center of each plate. Various attaching hardware is provided.
DIMENSIONS: 27 in. dia x 3 in. (686 mm dia x 76 mm).
WEIGHT: 250 lb (114 kg).
SUPPORTING TOOLS: Used with vertical balance machine.
TOOL MAINTENANCE: Lightly coat black oxide or black phosphate surfaces
with corrosion preventive oil.
QUANTITY PER OPERATION: One set.
REPLACEMENT PARTS LIST
GROUP PART NO. NOMENCLATURE QUANTITY SUPPLIER
NUMBER CODE
G01 2C14923P02 Pin 32
2C14923P03 Adapter 1
2C14923P04 Ring, Mounting 3
2C14923P05 Adapter 1
2C14923P06 Pin 20
2C14923P07 Bolt 16
2C14923P08 Spacer 1
2C14923P09 Adapter 1
2C14923P10 Bolt, Shoulder 20
FOR ALL
2C14923G01
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C14923G01
Page 2
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
ARBOR, BALANCE - FAN ROTOR
2C14924G01
PURPOSE AND USE: To hold the fan rotor during dynamic balancing.
DESCRIPTION: The non-rotating portion of the arbor locates on the work
supports so that the fan rotor is overhung. The fan rotor is supported on
bearings in a manner similar to the engine set up.
DIMENSIONS: 56 in. x 20 in. dia (1422 mm x 508 mm dia).
WEIGHT: 300 lb (136 kg).
SUPPORTING TOOLS: Schenck RJ50U balance machine.
TOOL MAINTENANCE: Coat black oxide or black phosphate surfaces
with corrosion preventive oil.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: This tool has an extensive parts list that would be of little
value without the drawing. Refer to drawing 2C14924.
FOR ALL
2C14924G01
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C14924G01
Page 2
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
TOOL SET, BALANCE, HIGH PRESSURE TURBINE ROTOR
2C14925G01
NOTE: Shop must check with manufacturer of shop's balance machine to make
sure of compatibility with this tooling.
REPLACEMENT PARTS LIST
GROUP PART NO. NOMENCLATURE QUANTITY SUPPLIER
NUMBER CODE
G01 2C14925P02 Spacer 1
2C14925P03 Adapter, Drive 1
2C14925P04 Nut 1
2C14925P05 Ring 1
FOR ALL
2C14925G01
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C14925G01
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
ARBOR, BALANCE - FAN ROTOR
2C14926G01
PURPOSE AND USE: To hold the fan rotor during dynamic balancing.
DESCRIPTION: The arbor consists of a steel tube upon which another steel tube is
welded. A steel ring provides the interface with the engine hardware.
DIMENSIONS: 28 in. x 8.5 in. dia (711 mm x 216 in. dia).
WEIGHT: 300 lbs (136 kg).
SUPPORTING TOOLS: Used with 2C6075, 2C14928, 2C14929, and 2C14930.
TOOL MAINTENANCE: Lightly coat black oxide or black phosphate surfaces
with corrosion preventive oil.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS LIST
GROUP PART NO. NOMENCLATURE QUANTITY SUPPLIER
NUMBER CODE
G01 2C14926P02 Arbor 1
2C14926P03 Ring 1
2C14926P04 Bolt, Shear 5
2C14926P05 Cap 1
2C14926P06 Link 1
2C14926P07 Clevis 1
9691M14Pll Nut, Self-locking 5 OP
CL-12-2BLPT-2.50 Pin, Ball Lock 1 I
No. 8 Chain, Sash 1 R
28420-250A-48 Pin, Dowel 1 U
133091 Ring, Chain 1 ER
S-213-.875 Shackle 1 S
FOR ALL
2C14926G01
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C14926G01
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
SHROUD, BALANCE - FAN ROTOR WITHOUT STAGE 1 BLADES
2C14928G02
PURPOSE AND USE: The Balance Shroud is used to enclose the fan
rotor during balance operations.
DESCRIPTION: The Balance Shroud is an aluminum and steel clam shell type enclosure
supported on four steel legs. The primary color of the tool is blue.
DIMENSIONS: 76 x 32 in. (1930 x 813 mm).
WEIGHT: 950 lb (431 kg).
SUPPORTING TOOLS: Shank Balance Machine RL50 or HL50.
TOOL MAINTENANCE: TBD
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing 2C14928.
FOR ALL
2C14928G02
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C14928G02
Page 2
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
DOLLY, INSTALLATION - FAN ROTOR/BALANCE ARBOR WITHOUT STAGE 1 BLADES
2C14929G01
PURPOSE AND USE: The Installation Dolly is used to help with the assembly of
the arbor onto the fan booster rotor (without stage 1 blades).
DESCRIPTION: The Installation Dolly is a square frame base with cross
supports to hold a vertical tube into which the arbor is placed. The
primary color of the tool is blue.
DIMENSIONS: 56 x 56 x 35 in. (1422 x 1422 x 889 mm).
WEIGHT: 350 lb (159 kg).
SUPPORTING TOOLS: 2C14926, 2C14928, 2C14929, 2C14930.
TOOL MAINTENANCE: TBD
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing 2C14929.
FOR ALL
2C14929G01
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C14929G01
Page 2
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FIXTURE, LIFT AND TURN - FAN ROTOR ASSEMBLY
2C14930G01
PURPOSE AND USE: The Lift and Turn Fixture is used to lift and turn the fan
rotor assembly while it is installed in 2C14928 and 2C14929.
DESCRIPTION: The Lift and Turn Fixture is a V-shaped lift bar mounted on
a ring that attaches to the stage 1 fan disk or stage 2 thru 5 fan rotor
spool. The primary color of the tool is blue.
DIMENSIONS: 36 x 4 in. (914 x 102 mm).
WEIGHT: 55 lb (25 kg).
SUPPORTING TOOLS: 2C14928, 2014929.
TOOL MAINTENANCE: TBD
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing 2C14930.
FOR ALL
2C14930G01
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C14930G01
Page 2
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
ADAPTER, DRIVE - BALANCE, FAN MID SHAFT
2C14931G02
PURPOSE AND USE: The drive adapter is used to balance the fan mid shaft.
DESCRIPTION: The drive adapter is composed of a cap, race, and nut. This
tool has a black oxide or black phosphate finish.
DIMENSIONS: 3.75 x 7.4 in. (95 x 188 mm).
WEIGHT: 40 lbs (18.2 kg).
SUPPORTING TOOLS: Drive Shaft.
TOOL MAINTENANCE: Apply corrosion preventive oil to all surfaces that
have black oxide or black phosphate coating.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing 2C14931.
NOTE: Shop must check with manufacturer of shop's balance machine to make
sure of compatibility with this tooling.
FOR ALL
2C14931G02
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C14931G02
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
PROGRAM, BALANCE - BLADE REPLACEMENT
2C14932G01
PURPOSE AND USE: To assist the location of compressor blades around the disk of
the compressor rotor at initial build or partial blade replacement.
DESCRIPTION: The tool consists of a program on a diskette. The G01
version was superseded by 9446M61G03.
DIMENSIONS: 3.50 x 3.50 x 0.125 in. (88.9 x 88.9 x 3.18 mm).
WEIGHT: 0.2 lb (0.1 kg).
SUPPORTING TOOLS: Used with IPM-PC or compatible.
TOOL MAINTENANCE: None.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS LIST
GROUP PART NO. NOMENCLATURE QUANTITY SUPPLIER
NUMBER CODE
G01 2C14932P02 Program, BRIBPCF6.EXE 1
2C14932P03 Diskette, 3.5 1
2C14932P04 Container 1
FOR ALL
2C14932G01
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C14932G01
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
PROGRAM, BALANCE - BLADE REPLACEMENT
2C14932G02
PURPOSE AND USE: To assist the location of compressor blades around the disk of
the compressor rotor at initial build or partial blade replacement.
DESCRIPTION: The tool consists of a program on a diskette. The G02
version was superseded by 9446M61G03.
DIMENSIONS: 5.25 x 5.25 x 0.125 in. (133 x 133 x 3 mm).
WEIGHT: 0.2 lb (0.1 kg).
SUPPORTING TOOLS: Used with IPM-PC or compatible.
TOOL MAINTENANCE: None.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS LIST
GROUP PART NO. NOMENCLATURE QUANTITY SUPPLIER
NUMBER CODE
G02 2C14932P02 Program, BRIBPCF6.EXE 1
2C14932P03 Diskette, 3.5 1
2C14932P04 Container 1
FOR ALL
2C14932G02
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C14932G02
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
PROGRAMMER, FADEC - ENGINE SERIAL NUMBER
2C14933G01
PURPOSE AND USE: The FADEC Programmer is used to program a selected engine serial
number into the electronic control unit non-volatile memory.
DESCRIPTION: The FADEC Programmer consists of thirteen switches
mounted in a container with an eight-foot cable. The G01 version is
used with CF6-80C2 engines only.
DIMENSIONS: Container, 9 x 4 x 8 in. (229 x 102 x 203 mm).
WEIGHT: 5 lbs (2 kg).
SUPPORTING TOOLS: None.
TOOL MAINTENANCE: None.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing 2C14933.
REPLACEMENT PARTS LIST
GROUP PART NO. NOMENCLATURE QUANTITY SUPPLIER
NUMBER CODE
G01 2C14933P02 Container 1
2C14933P03 Cable, Assembly 1
2C14933P04 Panel, Mounting 1
MS16996-37 Screw, SKT HD CAP 4
- STL
62111121-0-9-V Switch, Rocker 10
62151121-0-9-B Switch, Rocker 3
1237 TYPE SJT-18/3 Relief, Strain 1
FOR FADEC
2C14933G01
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR FADEC
2C14933G01
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
PROGRAMMER, FADEC - ENGINE SERIAL NUMBER
2C14933G02
PURPOSE AND USE: The FADEC Programmer is used to program a selected engine serial
number into the electronic control unit non-volatile memory.
DESCRIPTION: The FADEC Programmer consists of thirteen switches mounted
in a container with an eight-foot cable. The G02 version is used with
both CF6-80C2 and CF6-80E1 engines.
DIMENSIONS: Container, 9 x 4 x 8 in. (229 x 102 x 203 mm).
WEIGHT: 5 lbs (2 kg).
SUPPORTING TOOLS: None.
TOOL MAINTENANCE: None.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing 2C14933.
REPLACEMENT PARTS LIST
GROUP PART NO. NOMENCLATURE QUANTITY SUPPLIER
NUMBER CODE
G02 2C14933P02 Container 1
2C14933P03 Cable, Assembly 1
2C14933P09 Panel, Mounting 1
MS16996-37 Screw, SKT HD CAP 4
- STL
62111121-0-9-V Switch, Rocker 10
62151121-0-9-B Switch, Rocker 3
1237 TYPE SJT-18/3 Relief, Strain 1
FOR FADEC
2C14933G02
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR FADEC
2C14933G02
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
PROGRAMMER, FADEC - ENGINE SERIAL NUMBER
2C14933G04
PURPOSE AND USE: The FADEC Programmer is used to program a selected engine serial
number into the electronic control unit non-volatile memory.
DESCRIPTION: The FADEC Programmer consists of thirteen switches mounted
in a container with an eight-foot cable. The G04 version is used with
both CF6-80C2 and CF6-80E1 engines.
DIMENSIONS: Container, 9 x 4 x 8 in. (229 x 102 x 203 mm).
WEIGHT: 5 lbs (2 kg).
SUPPORTING TOOLS: None.
TOOL MAINTENANCE: None.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing 2C14933.
REPLACEMENT PARTS LIST
GROUP PART NO. NOMENCLATURE QUANTITY SUPPLIER
NUMBER CODE
G04 2C14933P02 Container 1
2C14933P03 Cable, Assembly 1
2C18073G01 Cable, Assembly 1
2C14933P11 Panel, Mounting 1
MS16996-37 Screw, SKT HD CAP 4
- STL
62111121-0-9-V Switch, Rocker 10
621511121-0-9-B Switch, Rocker 3
1237 TYPE SJT-18/3 Relief, Strain 1
FOR FADEC
2C14933G04
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR FADEC
2C14933G04
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
PROGRAM RETRIEVAL - NVM DATA, FADEC ECU (GEMSAV)
2C14934G01
PURPOSE AND USE: To retrieve the non-volatile memory (NVM) from the electronic
control unit (ECU) on wing to be used for engine analysis.
DESCRIPTION: The tool consists of a floppy disk containing the
program and a container.
DIMENSIONS: 5 x 8 x 1 in. (127 x 203 x 25 mm).
WEIGHT: 0.2 lb (0.1 kg).
SUPPORTING TOOLS: Used with 2C14973.
TOOL MAINTENANCE:
QUANTITY PER OPERATION:
REPLACEMENT PARTS LIST
GROUP PART NO. NOMENCLATURE QUANTITY SUPPLIER
NUMBER CODE
G01 2C14834P02 Program, GEMSAVII.EXE 1
2C14834P03 Diskette 1
2C14834P04 Container 1
2C14934P05 Users Manual 1
FOR FADEC
2C14934G01
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR FADEC
2C14934G01
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
ARBOR ASSEMBLY, BALANCE - FAN ROTOR SPINNER
2C14935G03
PURPOSE AND USE: The Arbor Balance Assembly is used to support the fan rotor spinner
in a horizontal dynamic balance machine during dynamic balancing.
DESCRIPTION: The Arbor Balance Assembly is a common aluminum arbor shaft,
fan rotor support spoked frame, and a steel fan rotor spinner adapter. The
tool has a black oxide or black phosphate finish.
DIMENSIONS: 36 x 34 in. (914 x 864 mm).
WEIGHT: 300 lb (136 kg).
SUPPORTING TOOLS: Horizontal Dynamic Balance Machine.
TOOL MAINTENANCE: Apply corrosion preventive oil to all surfaces that
have black oxide or black phosphate coating.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing 2C14935.
FOR ALL
2C14935G03
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C14935G03
Page 2
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
PROBE, PRESSURE/TEMPERATURE - FAN DISCHARGE
2C14952G01
PURPOSE AND USE: To measure the temperature (Tt25) and pressure (Pt25) at
the high pressure compressor inlet during engine test.
DESCRIPTION: Consists of a probe, gasket, mounting hardware, and a
container. The G01 version of 2C14952 is made of chromel constantan
alloy and is the recommended tool.
DIMENSIONS: 5 x 20 x 3 in. (127 x 51 x 76 mm).
WEIGHT: 1 lb (0.45 kg).
SUPPORTING TOOLS: Engine test equipment.
TOOL MAINTENANCE: Apply a light coat of corrosion preventive oil to
all treated surfaces when stored.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS LIST
GROUP PART NO. NOMENCLATURE QUANTITY SUPPLIER
NUMBER CODE
G01 2C14952P02 Washer 1
2C14952P03 Container 1
2C14954P01 Probe 1
MS20995C32 Lockwire AR
MS9034-8 Mach. Bolt 4
FOR ALL
2C14952G01
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C14952G01
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
PROBE, PRESSURE/TEMPERATURE - FAN DISCHARGE
2C14952G02
PURPOSE AND USE: To measure the temperature (Tt25) and pressure (Pt25) at
the high pressure compressor inlet during engine test.
DESCRIPTION: Consists of a probe, gasket, mounting hardware, and a container. It
is an alternate to G01 and is made of copper constantan alloy.
DIMENSIONS: 5 x 20 x 3 in. (127 x 51 x 76 mm).
WEIGHT: 1 lb (0.45 kg).
SUPPORTING TOOLS: Engine test equipment.
TOOL MAINTENANCE: Apply a light coat of corrosion preventive oil to
all treated surfaces when stored.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS LIST
GROUP PART NO. NOMENCLATURE QUANTITY SUPPLIER
NUMBER CODE
G02 2C14952P02 Washer 1
2C14952P03 Container 1
2C14954P02 Probe 1
MS20995C32 Lockwire AR
MS9034-8 Mach. Bolt 4
FOR ALL
2C14952G02
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C14952G02
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
PROBE, PRESSURE/TEMPERATURE - FAN DISCHARGE
2C14952G03
PURPOSE AND USE: To measure the temperature (Tt25) and pressure (Pt25) at
the high pressure compressor inlet during engine test.
DESCRIPTION: Consists of a probe, gasket, mounting hardware, and a container. It
is an alternate to G01 and is made of iron constantan alloy.
DIMENSIONS: 5 x 20 x 3 in. (127 x 51 x 76 mm).
WEIGHT: 1 lb (0.45 kg).
SUPPORTING TOOLS: Engine test equipment.
TOOL MAINTENANCE: Apply a light coat of corrosion preventive oil to
all treated surfaces when stored.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS LIST
GROUP PART NO. NOMENCLATURE QUANTITY SUPPLIER
NUMBER CODE
G03 2C14952P02 Washer 1
2C14952P03 Container 1
2C14954P03 Probe 1
MS20995C32 Lockwire AR
MS9034-8 Mach. Bolt 1
FOR ALL
2C14952G03
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C14952G03
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
PROBE, PRESSURE/TEMPERATURE - FAN DISCHARGE
2C14952G04
PURPOSE AND USE: To measure the temperature (Tt25) and pressure (Pt25) at
the high pressure compressor inlet during engine test.
DESCRIPTION: Consists of a probe, gasket, mounting hardware, and a container.
It is an alternate to G01 and is made of chromel alumel alloy.
DIMENSIONS: 5 x 20 x 3 in. (127 x 51 x 76 mm).
WEIGHT: 1 lb (0.45 kg).
SUPPORTING TOOLS: Engine test equipment.
TOOL MAINTENANCE: Apply a light coat of corrosion preventive oil to
all treated surfaces when stored.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS LIST
GROUP PART NO. NOMENCLATURE QUANTITY SUPPLIER
NUMBER CODE
G04 2C14952P02 Washer 1
2C14952P03 Container 1
2C14954P04 Probe 1
MS20995C32 Lockwire AR
MS9034-8 Mach. Bolt 1
FOR ALL
2C14952G04
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C14952G04
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
RAKE, TEMPERATURE - COMPRESSOR DISCHARGE
2C14953G01
PURPOSE AND USE: The temperature rake is used to measure the compressor discharge
temperature profile when running engine tests in a test cell.
DESCRIPTION: The temperature rake is five capped ungrounded thermocouples
contained in a stainless steel case. The lead from the temperature rake is
50 feet (15 meters) long with a mating quick disconnect on one end and five
standard thermocouple plugs on the other. The wire is made of chromel/alumel
alloy. The G01 version of this tool is obsolete and has a 24 in. (609.6
mm) lead with 50 feet (15.2 meters) jumper.
DIMENSIONS: Container, 10 x 10 x 5 in. (254 x 254 x 127 mm).
WEIGHT: 10 lbs (5 kg).
SUPPORTING TOOLS: Thermocouple readout.
TOOL MAINTENANCE: Do a fluorescent penetrant inspection after every 50 hours of use.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing 2C14953.
FOR PMC
2C14953G01
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR PMC
2C14953G01
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
RAKE, TEMPERATURE - COMPRESSOR DISCHARGE
2C14953G02
PURPOSE AND USE: The temperature rake is used to measure the compressor discharge
temperature profile when running engine tests in a test cell.
DESCRIPTION: The temperature rake is five capped ungrounded thermocouples
contained in a stainless steel case. The lead from the temperature rake is 50
feet (15 meters) long with a mating quick disconnect on one end and five standard
thermocouple plugs on the other. The wire is made of chromel/constantan alloy.
This tool is an alternate to the G03 version. The G02 version of this tool is
obsolete and has a 24 in. (609.6 mm) lead with 50 feet (15.2 meters) jumper.
DIMENSIONS: Container, 10 x 10 x 5 in. (254 x 254 x 127 mm).
WEIGHT: 10 lbs (5 kg).
SUPPORTING TOOLS: Thermocouple readout.
TOOL MAINTENANCE: Do a fluorescent penetrant inspection after every 50 hours of use.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing 2C14953.
FOR ALL
2C14953G02
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C14953G02
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
RAKE, TEMPERATURE - COMPRESSOR DISCHARGE
2C14953G03
PURPOSE AND USE: The temperature rake is used to measure the compressor discharge
temperature profile when running engine tests in a test cell.
DESCRIPTION: The temperature rake is five capped ungrounded thermocouples
contained in a stainless steel case. The lead from the temperature rake is 50
feet (15 meters) long with a mating quick disconnect on one end and five standard
thermocouple plugs on the other. The wire is made of chromel/alumel alloy.
DIMENSIONS: Container, 10 x 10 x 5 in. (254 x 254 x 127 mm).
WEIGHT: 10 lbs (5 kg).
SUPPORTING TOOLS: Thermocouple readout.
TOOL MAINTENANCE: Do a fluorescent penetrant inspection after every 50 hours of use.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing 2C14953.
FOR PMC
2C14953G03
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR PMC
2C14953G03
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
RAKE, TEMPERATURE - COMPRESSOR DISCHARGE
2C14953G04
PURPOSE AND USE: The temperature rake is used to measure the compressor discharge
temperature profile when running engine tests in a test cell.
DESCRIPTION: The temperature rake is five capped ungrounded thermocouples
contained in a stainless steel case. The lead from the temperature rake is
50 feet (15 meters) long with a mating quick disconnect on one end and five
standard thermocouple plugs on the other. The wire is made of chromel/constantan
alloy. This is an alternate to the G03 version.
DIMENSIONS: Container, 10 x 10 x 5 in. (254 x 254 x 127 mm).
WEIGHT: 10 lbs (5 kg).
SUPPORTING TOOLS: Thermocouple readout.
TOOL MAINTENANCE: Do a fluorescent penetrant inspection after every 50 hours of use.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing 2C14953.
FOR PMC
2C14953G04
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR PMC
2C14953G04
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
KIT, TRIM BALANCE - ENGINE
2C14963G04
PURPOSE AND USE: The Trim Balance Kit provides cables and connections to perform
trim balance of the fan rotor. The G04 is used with FADEC engines.
DESCRIPTION: This kit consists of three cables on reels and four adapter cables
stored in a container. The primary color of the container is blue.
DIMENSIONS: 15 x 20 x 20 in. (381 x 508 x 508 mm).
WEIGHT: 70 lbs (32 kg).
SUPPORTING TOOLS: 2C14965.
TOOL MAINTENANCE: TBD
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing 2C14963.
FOR FADEC
2C14963G04
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR FADEC
2C14963G04
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
KIT, TRIM BALANCE - ENGINE
2C14963G06
PURPOSE AND USE: The Trim Balance Kit provides cables and connections to perform
trim balance of the fan rotor. The G06 is used with PMC engines.
DESCRIPTION: This kit consists of two cables on reels and two adapter cables
stored in a container. The primary color of the container is blue.
DIMENSIONS: 15 x 20 x 20 in. (381 x 508 x 508 mm).
WEIGHT: 70 lbs (32 kg).
SUPPORTING TOOLS: 2C14965.
TOOL MAINTENANCE: TBD
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing 2C14963.
FOR PMC
2C14963G06
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR PMC
2C14963G06
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
DELETED
2C14963G07
PURPOSE AND USE: This tool has been deleted in its entirety.
FOR ALL
2C14963G07
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
ANALYZER, TRIM BALANCE - FAN
2C14965P01
PURPOSE AND USE: The trim balance analyzer is used to measure the amplitude
and location of fan rotor imbalance.
DESCRIPTION: The trim balance analyzer is self-contained in a portable carrying
case. The P01 version of 2C14965 is 120V/60 Hz.
DIMENSIONS: 10 x 13 x 14 in. (254 x 330 x 356 mm).
WEIGHT: 25 lbs (11 kg).
SUPPORTING TOOLS: 2C14963.
TOOL MAINTENANCE: See vendor literature.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing 2C14965.
NOTE: The following trim balance analyzing tools are optional replacements
for 2C14965: PBS-4100 (manufactured by MTI Instruments Inc.), and
Scientific-Atlanta BalancePro.
FOR ALL
2C14965P01
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C14965P01
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
ANALYZER, TRIM BALANCE - FAN
2C14965P02
PURPOSE AND USE: The trim balance analyzer is used to measure the amplitude
and location of fan rotor imbalance.
DESCRIPTION: The trim balance analyzer is self-contained in a portable carrying
case. The P02 version of 2C14965 is 230V/50 Hz.
DIMENSIONS: 10 x 13 x 14 in. (254 x 330 x 356 mm).
WEIGHT: 25 lbs (11 kg).
SUPPORTING TOOLS: 2C14963.
TOOL MAINTENANCE: See vendor literature.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing 2C14965.
NOTE: The following trim balance analyzing tools are optional replacements
for 2C14965: PBS-4100 (manufactured by MTI Instruments Inc.), and
Scientific-Atlanta BalancePro.
FOR ALL
2C14965P02
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C14965P02
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
TESTER, THERMOCOUPLE
2C14966G03
PURPOSE AND USE: The Thermocouple Tester is used to measure circuit/ insulation
resistance of the probes/harnesses of the exhaust gas temperature thermocouple
system. It is battery powered for flight line use and simulates chromel-alumel
thermocouple output to check aircraft wiring/ indicators.
DESCRIPTION: The Thermocouple Tester kit has a standard lead that terminates
in a pair of alligator clips and a DIN connector so that the standard lead
can be replaced with a switching box/test cable. The kit also includes
four shorting bars which replace the engine probes for certain tests.
The kit is housed in a storage container.
DIMENSIONS: Container, 15 x 26 x 18 in. (381 x 660 x 457 mm).
WEIGHT: 15 lb (7 kg).
SUPPORTING TOOLS: None.
TOOL MAINTENANCE: See vendor literature.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing 2C14966.
FOR ALL
2C14966G03
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C14966G03
Page 2
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
DIGITAL TURBINE TEMPERATURE TEST SET
2C14966G06
PURPOSE AND USE: The TT1200A is specifically designed to test and calibrate
Chromel-Alumel (CH-AL) temperature indicating systems and provides the means for
quickly troubleshooting aircraft temperature indicating systems.
DESCRIPTION: The functions of the front panel switches and components are the power
pushbutton, backlight pushbutton, temperature adjustment control knob, fine control,
function switch, range switch, press to measure button, press to set button, system
resistance control knob, test connector, menu pushbutton, contrast pushbutton,
millivolt pushbutton, fahrenheit and celsius pushbuttons, and two battery holders.
DIMENSIONS: Container, 7 x 11 x 10 in. (178 x 279 x 254 mm).
WEIGHT: 7.3 lb (3.3 kg).
SUPPORTING TOOLS: None.
TOOL MAINTENANCE: See vendor's manual.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing 2C14966.
FOR ALL
2C14966G06
Page 1
Dec 01/2014
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C14966G06
Page 2
Dec 01/2014
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
HOSE, STARTER - AIR
2C14967G01
PURPOSE AND USE: To connect the starter to the substitute air supply system.
DESCRIPTION: This starter hose consists of a hose, and elbow. The G01
version of 2C14967 uses an Air Research starter.
DIMENSIONS: 4 in. dia x 80 in. (102 mm dia x 2,032 mm).
WEIGHT: 100 lbs (46 kg).
SUPPORTING TOOLS: Air supply system at the engine test site pylon.
TOOL MAINTENANCE: None required.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS LIST
GROUP PART NO. NOMENCLATURE QUANTITY SUPPLIER
NUMBER CODE
G01 2C14967P03 Tube Assembly 1
2C14967P04 Hose and Tube Assembly 1
E17D87 Coupling 2 CE
2703-400 Coupling 1 CM
2873-400 Coupling E-Ring 1 CM
FOR ALL
2C14967G01
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C14967G01
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
HOSE, STARTER - AIR
2C14967G02
PURPOSE AND USE: To connect the starter to the substitute air supply system.
DESCRIPTION: This starter hose consists of a hose, elbow, and an adapter. The G02
version of 2C14967 is an alternate to G01 that uses a Hamilton Standard starter.
DIMENSIONS: 4 in. dia x 80 in. (102 mm dia x 2,032 mm).
WEIGHT: 100 lbs (46 kg).
SUPPORTING TOOLS: Air supply system at the engine test site pylon.
TOOL MAINTENANCE: None required.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS LIST
GROUP PART NO. NOMENCLATURE QUANTITY SUPPLIER
NUMBER CODE
G02 2C14967P03 Tube Assembly 1
2C14967P04 Hose and Tube Assembly 1
2C14967P05 Hamilton Standard 1
Adapter
E17D87 Coupling 2 CE
2703-400 Coupling 1 CM
2873-400 E-Ring 1 CM
6354-450 Coupling 1 CM
A0863 E-Seal 1 CM
FOR ALL
2C14967G02
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C14967G02
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
SET, TRANSMITTER - VARIABLE BYPASS VALVE POSITION
2C14968G01
FOR PMC
2C14968G01
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR PMC
2C14968G01
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
READER, POWER MANAGEMENT CONTROL - MAINTENANCE FAULT
2C14969G04
PURPOSE AND USE: The Power Management Control Reader is used to read
the maintenance report from the non-volatile memory of the PMC for
time maintenance corrective action.
DESCRIPTION: The Power Management Control Reader consists of an electronic
reading instrument and a cable. A container is also provided.
DIMENSIONS: 6 x 12 x 14 in. (152 x 305 x 356 mm).
WEIGHT: 8 lbs (4 kg).
SUPPORTING TOOLS: None.
TOOL MAINTENANCE: None.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing 2C14969.
FOR PMC
2C14969G04
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR PMC
2C14969G04
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
TRIMMER, VARIABLE STATOR VANE
2C14970P01
PURPOSE AND USE: To remotely trim the variable stator vane (VSV)
adjustment on the main engine control.
DESCRIPTION: The tool is an L-shaped aluminum housing that contains a 24 volt DC
motor that drives a female hex driver through a slip clutch. A clamp is attached to
the trimmer housing to attach the trimmer unit to the VSV cable housing.
DIMENSIONS: 3 x 4 x 3 in. (76 x 102 x 76 mm).
WEIGHT: 3 lbs (1.4 kg).
SUPPORTING TOOLS: None.
TOOL MAINTENANCE: No special requirements.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: None.
FOR PMC
2C14970P01
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR PMC
2C14970P01
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
CABLE ASSEMBLY, TRIM BALANCE - ENGINE
2C14971G01
PURPOSE AND USE: The Cable Assembly is used to connect 2C14232 to the engine.
DESCRIPTION: The Cable Assembly is a single cable with connectors on
both ends. It does not have a special container for storage because it
can be stored in the container for 2C14232.
DIMENSIONS: 1 x 84 in. (25 x 2134 mm).
WEIGHT: 1 lb (0.5 kg).
SUPPORTING TOOLS: 2C14232.
TOOL MAINTENANCE: None.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing 2C14971.
FOR ALL
2C14971G01
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C14971G01
Page 2
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
SYSTEM, REPROGRAMMING - FADEC - ECU/CPU
2C14973G04
PURPOSE AND USE: The reprograming system is used to install a new version of
non-volatile memory (NVM) from diskette to the electronic control unit (ECU).
DESCRIPTION: The reprograming system consists of a portable computer, a cable, and
a dual RS 232 port cartridge. This tool is obsolete except for cable.
DIMENSIONS: 20 x 15 x 8 in. (508 x 381 x 203 mm).
WEIGHT: 30 lbs (14 kg).
SUPPORTING TOOLS: 9470M16, 9470M17, 9470M18, 9470M19.
TOOL MAINTENANCE: Protect from heat and moisture. Discharge and
recharge the battery monthly.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing 2C14973.
FOR FADEC
2C14973G04
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR FADEC
2C14973G04
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
SYSTEM, REPROGRAMMING - FADEC - ECU/CPU
2C14973G05
PURPOSE AND USE: The reprogramming system is used to install a new version of
non-volatile memory (NVM) from diskette to the electronic control unit (ECU).
DESCRIPTION: The reprogramming system consists of a portable computer, a cable,
and a dual RS 232 port cartridge. G05 has power supplies and a programmable
eraser. This tool is obsolete except for power supply and cable.
DIMENSIONS: 20 x 15 x 8 in. (508 x 381 x 203 mm).
WEIGHT: 30 lbs (14 kg).
SUPPORTING TOOLS: 9470M16, 9470M17, 9470M18, 9470M19.
TOOL MAINTENANCE: Protect from heat and moisture. Discharge and
recharge the battery monthly.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing 2C14973.
FOR FADEC
2C14973G05
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR FADEC
2C14973G05
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
SYSTEM, REPROGRAMMING - FADEC - ECU/CPU
2C14973G06
PURPOSE AND USE: The reprogramming system is used to install a new version of
non-volatile memory (NVM) from diskette to the electronic control unit (ECU).
DESCRIPTION: The reprogramming system consists of a portable computer, a
cable, and a dual RS 232 port cartridge. G06 has power supplies. This tool
is obsolete, except for power supply and cable.
DIMENSIONS: 20 x 15 x 8 in. (508 x 381 x 203 mm).
WEIGHT: 30 lbs (14 kg).
SUPPORTING TOOLS: 9470M16, 9470M17, 9470M18, 9470M19.
TOOL MAINTENANCE: Protect from heat and moisture. Discharge and
recharge the battery monthly.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing 2C14973.
FOR FADEC
2C14973G06
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR FADEC
2C14973G06
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
UNIT, ENGINE PRESERVATION - HYDRO-MECHANICAL UNIT
2C14974G02
PURPOSE AND USE: The engine preservation unit is used to flush oil through the
hydro-mechanical unit, fuel-driven activators, and fuel manifolds for fuel system
preservation of FADEC engines. To adapt to PMC engines, use cable 2C14286G01.
DESCRIPTION: The engine preservation unit has a control panel mounted on a container
with three interfacing cables. The lid has four clips to store the cables.
DIMENSIONS: 16 x 8 x 8 in. (406 x 203 x 203 mm).
WEIGHT: 10 lbs (5 kg).
SUPPORTING TOOLS: None.
TOOL MAINTENANCE: TBD
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing 2C14974.
FOR FADEC
2C14974G02
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR FADEC
2C14974G02
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FILTER, TEST - SCAVENGE OIL, 3 MICRON
2C14975G01
PURPOSE AND USE: This tool is used as a slave filter during engine test only.
DESCRIPTION: The test filter consists of a filter bowl, filter cap,
fitting connector, cap, and filter.
DIMENSIONS: 5 in. dia x 12 in. (127 mm dia x 305 mm).
WEIGHT: 0.10 lb (0.05 kg).
SUPPORTING TOOLS: Pressure Gages.
TOOL MAINTENANCE: Not required
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing 2C14975.
FOR ALL
2C14975G01
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C14975G01
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
SLING - PRIMARY NOZZLE
2C14979G01
PURPOSE AND USE: This fixture is used to remove the nozzle from the
shipping container and install on the engine.
DESCRIPTION: The fixture consists of a main metal strap divided in two
steel plates that have two adjustable latches.
DIMENSIONS: 59 x 60 x 120 in. (1,270 x 1,524 x 3,048 mm).
WEIGHT: 70 lbs (31.8 kg).
SUPPORTING TOOLS: Overhead hoist with minimum capacity of 1,000 lbs (453.6 kg).
TOOL MAINTENANCE: Apply corrosion preventive oil to all surfaces
that have black oxide finish.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing 2C14979.
FOR ALL
2C14979G01
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C14979G01
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FIXTURE, LIFT — ROTATING INTERSTAGE SEAL
2C14981G01
PURPOSE AND USE: This fixture is used to lift the rotating interstage seal for
installation/removal from the stage 1 disk on boltless, R88DT rotors.
DESCRIPTION: This lift fixture tool consists of a lift ring which has two split
rings that are connected by four captive screws. The inner wall of the lift ring
at the bottom side has a flange that allows the tool to grab the aft side of the
rotating interstage seal (RIS). A clocking bar aligns the tool to the RIS, and a
guide pin aligns the RIS to the HPT rotor dovetail. Three hoist rings at the top
are used to attach the tool to a 3-point lift chain during lifting and lowering.
DIMENSIONS: 6.0 x 24.5 x 24.5 in. (152 x 622 x 622 mm).
WEIGHT: 22 lbs (10.0 kg).
SUPPORTING TOOLS: Three-point lift chain, overhead crane, work table,
7C2141G01, 2C18092G01, temperature-resistant gloves.
TOOL MAINTENANCE: Coat treated surfaces with corrosion preventive oil.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing 2C14981.
FOR B8F
2C14981G01
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR B8F
2C14981G01
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FIXTURE, CHILL — REMOVAL, BLADE RETAINER, STAGE 1
2C14983G01
PURPOSE AND USE: This fixture is used to hold dry ice positioned for
vertical high pressure turbine rotor stage 1 blade retainer removal. It
is used with boltless, R88DT rotors only.
DESCRIPTION: This is a ring-shaped tool with an outer and inner diameter ring.
It includes two half-rings for positioning on the aft blade retainer. The
space between the ring walls is used for dry ice and liquid nitrogen to chill
the aft blade retainer and help with removal from the disk.
DIMENSIONS: 2 x 25 x 25 in. (51 x 635 x 635 mm).
WEIGHT: 4 lbs (1.8 kg).
SUPPORTING TOOLS: Liquid nitrogen, dry ice, temperature-resistant gloves,
apron, face shield or safety goggles.
TOOL MAINTENANCE: None.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing 2C14983.
FOR B8F
2C14983G01
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR B8F
2C14983G01
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FIXTURE, INSPECTION — COMBUSTOR DOME
2C15004G03
PURPOSE AND USE: This fixture is used to hold the dome after repair for inspection.
DESCRIPTION: The tool consists of a base that has attached to it two rings
that locate the outer diameter, inner diameter, and the inner surface of
the dome. Shoulder screw locator assemblies attach the dome to the fixture.
Plug assemblies are provided for inspection of the bolt holes, the igniters,
and swirl nozzles. A dial indicator is provided to check dome height. The
G03 version of this tool is used for dome 9382M99.
DIMENSIONS: 36.5 in. dia x 10 in. (927 mm dia x 254 mm).
WEIGHT: 750 lbs (340 kg).
SUPPORTING TOOLS: This fixture is used in combination with overhead hoist.
TOOL MAINTENANCE: Apply corrosion preventive oil to all surfaces
that have black oxide finish.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing 2C15004.
FOR ALL
2C15004G03
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C15004G03
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FIXTURE, INSPECTION - COMBUSTOR DOME
2C15004G04
PURPOSE AND USE: This fixture is used to hold the dome after repair for inspection.
DESCRIPTION: The tool consists of a base that has attached to it two rings
that locate the outer diameter, inner diameter, and the inner surface of
the dome. Shoulder screw locator assemblies attach the dome to the fixture.
Plug assemblies are provided for inspection of the bolt holes, the igniters,
and swirl nozzles. A dial indicator is provided to check dome height. The
G04 version of this tool is used for dome 9559M31.
DIMENSIONS: 36.5 in. dia x 10 in. (927 mm dia x 254 mm).
WEIGHT: 750 lbs (340 kg).
SUPPORTING TOOLS: This fixture is used in combination with overhead hoist.
TOOL MAINTENANCE: Apply corrosion preventive oil to all surfaces
that have black oxide finish.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing 2C15004.
FOR ALL
2C15004G04
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C15004G04
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FIXTURE, RESIZE - COMBUSTOR DOME
2C15006G03
FOR ALL
2C15006G03
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C15006G03
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FIXTURE, HEAT TREAT, COMBUSTOR DOME
2C15007G01
FOR ALL
2C15007G01
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C15007G01
Page 2
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FIXTURE, HEAT TREAT, COMBUSTOR LINERS
2C15008G01
PURPOSE AND USE: The Heat Treat Fixture is used to support and keep flatness
of the combustor liners during anneal and stress relief.
DESCRIPTION: The Heat Treat Fixture is a split support ring for the outer liner.
DIMENSIONS: 32 x 4 in. (813 x 102 mm).
WEIGHT: 10 lbs (5 kg).
SUPPORTING TOOLS: Heat treat facility.
TOOL MAINTENANCE: Apply corrosion preventive oil to all surfaces that
have black oxide or black phosphate coating.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing 2C15008.
FOR ALL
2C15008G01
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C15008G01
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FIXTURE, HEAT TREAT, COMBUSTOR LINERS
2C15008G02
PURPOSE AND USE: The Heat Treat Fixture is used to support and keep flatness
of the combustor liners during anneal and stress relief.
DESCRIPTION: The Heat Treat Fixture is a split support ring for the outer liner.
The G02 version adds a new outer liner support that is used with CF6-80A engines.
DIMENSIONS: 32 x 4 in. (813 x 102 mm).
WEIGHT: 10 lb (5 kg).
SUPPORTING TOOLS: Heat treat facility.
TOOL MAINTENANCE: Apply corrosion preventive oil to all surfaces that
have black oxide or black phosphate coating.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing 2C15008.
FOR ALL
2C15008G02
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C15008G02
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FIXTURE, ASSEMBLY/INSPECT - COMBUSTOR
2C15010G04
PURPOSE AND USE: This Fixture is used to inspect the inner liner, the outer
liner and properly to align the dome and the outer cowl.
DESCRIPTION: This fixture is mounted on a special stand to which the base plate is
attached. The outer liner attaches to the outer portion of the base. A second
plate is attached to the base to support the inner liner. A column attaching to the
base supports a top plate so various locators can interface with the swirlers.
DIMENSIONS: 55 x 38 x 38 in. (1,397 x 965 x 965 mm).
WEIGHT: 450 lbs (204 kg).
SUPPORTING TOOLS: None.
TOOL MAINTENANCE: Apply corrosion preventive oil to all surfaces
that have black oxide finish.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing 2C15010.
FOR ALL
2C15010G04
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C15010G04
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FIXTURE, ASSEMBLY/INSPECT - COMBUSTOR
2C15010G05
PURPOSE AND USE: This Fixture is used to inspect the inner liner, the outer
liner and properly to align the dome and the outer cowl.
DESCRIPTION: This fixture is mounted on a special stand to which the base plate is
attached. The outer liner attaches to the outer portion of the base. A second
plate is attached to the base to support the inner liner. A column attaching to the
base supports a top plate so various locators can interface with the swirlers. The
G05 version uses a different locator dome and inner support ring than G04.
DIMENSIONS: 55 x 38 x 38 in. (1,397 x 965 x 965 mm).
WEIGHT: 450 lbs (204 kg).
SUPPORTING TOOLS: None.
TOOL MAINTENANCE: Apply corrosion preventive oil to all surfaces
that have black oxide finish.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing 2C15010.
FOR ALL
2C15010G05
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C15010G05
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FIXTURE, ASSEMBLY/INSPECT - COMBUSTOR
2C15010G06
PURPOSE AND USE: This Fixture is used to inspect the inner liner, the outer
liner and properly to align the dome and the outer cowl.
DESCRIPTION: This fixture is mounted on a special stand to which the base plate is
attached. The outer liner attaches to the outer portion of the base. A second
plate is attached to the base to support the inner liner. A column attaching to
the base supports a top plate so various locators can interface with the swirlers.
The G06 version uses a different inner support ring than G05.
DIMENSIONS: 55 x 38 x 38 in. (1,397 x 965 x 965 mm).
WEIGHT: 450 lbs (204 kg).
SUPPORTING TOOLS: None.
TOOL MAINTENANCE: Apply corrosion preventive oil to all surfaces
that have black oxide finish.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing 2C15010.
FOR ALL
2C15010G06
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C15010G06
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FIXTURE, HOLDING - COMPRESSOR ROTOR SPOOL SHAFT
2C15023G01
PURPOSE AND USE: To support the high pressure compressor rotor shaft spool
at flange surface with the aft end down for grit blasting, shot peening
and thermal spray of spool forward flange.
DESCRIPTION: The fixture consists of two circular rings spaced by
six vertical tubular members.
DIMENSIONS: 21 in. dia x 18 in. (533 mm dia x 457 mm).
WEIGHT: 175 lb (79.5 kg).
SUPPORTING TOOLS: Grit blast, shot peen, and thermal spray equipment.
TOOL MAINTENANCE: Lightly coat black oxide or black phosphate surfaces
with corrosion preventive oil.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS LIST
GROUP PART NO. NOMENCLATURE QUANTITY SUPPLIER
NUMBER CODE
G01 2C15023P02 Support 1
2C15023P03 Protector 1
CL-20-HR Ring, Hoist 3 I
FOR ALL
2C15023G01
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C15023G01
Page 2
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
GAGE, INSPECTION - COMPRESSOR ROTOR SPOOL SHAFT
2C15026G02
PURPOSE AND USE: To measure the machined radii after machining the aluminum
rub coat on the compressor rotor spool shaft.
DESCRIPTION: The gage consists of a support assembly, set master,
top ring, and a container.
DIMENSIONS: 12 x 17 x 22 in. (305 x 432 x 559 mm).
WEIGHT: 110 lb (50 kg).
SUPPORTING TOOLS: Used with machining fixture 2C6537.
TOOL MAINTENANCE: Lightly coat black oxide or black phosphate surfaces
with corrosion preventive oil.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS LIST
GROUP PART NO. NOMENCLATURE QUANTITY SUPPLIER
NUMBER CODE
G02 2C15026P03 Bushing, Split 4
2C15026P13 Support 1
2C15026P14 Ring, Top 1
2C15026P15 Setmaster 1
2C15026P16 Container 1
B3Q, 3 in. Dial Indicator 2 AV
B3Q, 5 in. Dial Indicator 2 AV
FOR ALL
2C15026G02
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C15026G02
Page 2
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
TOOL SET, INSTALL/REMOVE - SHANK NUTS, HPTR AND HPCR
2C15031G02
PURPOSE AND USE: To remove self locking nuts from HPT disk or compressor
rotor spool shaft and replace them with new nuts.
DESCRIPTION: This tool set consists of a hydraulic powered hand tool with two
drivers, two flaring anvils, two removal anvils, a hydraulic cylinder which
creates a forward force that is reacted by one of the anvils.
DIMENSIONS: 18 x 10 x 8 in. (457 x 254 x 203 mm).
WEIGHT: 10 lb (4.5 kg).
SUPPORTING TOOLS: 3000 psig hydraulic pump and shop air.
TOOL MAINTENANCE: Coat treated surfaces (black oxide or black phosphate)
with corrosion preventive light oil when stored.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: This tool set has an extensive parts list that will be of
little value without the drawing. Refer to GE drawing 2C15031.
FOR ALL
2C15031G02
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C15031G02
Page 2
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FIXTURE, MACHINING AND INSPECTION - HIGH PRESSURE TURBINE PRESSURE TUBE COUPLING NUT
2C15042G03
PURPOSE AND USE: The Machining and Inspection Fixture is used to restrain
the HPT tube coupling nut at the buttress threads during inspection
and machining of the forward face.
DESCRIPTION: The Machining and Inspection Fixture consists of an expansion
arbor with external threads, a forward flange with three tapped holes and
six cutouts, and a knurled master nut with internal threads. The tool
has a black oxide or black phosphate finish.
DIMENSIONS: 12 x 9 in. (305 x 229 mm).
WEIGHT: 120 lb (54 kg).
SUPPORTING TOOLS: Rotab.
TOOL MAINTENANCE: Do an inspection and check the calibration of the tool
periodically. Refer to drawing 2C15042. Apply corrosion preventive oil to all
surfaces that have a black oxide or black phosphate finish.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing 2C15042.
FOR ALL
2C15042G03
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C15042G03
Page 2
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FIXTURE, MACHINING - COMPRESSOR REAR FRAME - AFT SUMP
2C15049G02
PURPOSE AND USE: To position and hold the compressor rear frame aft
sump for machining of functional diameter.
DESCRIPTION: The fixture consists of a clamp ring, a base, a
support ring and a clamp plate.
DIMENSIONS: 19 in. dia x 12 in. (483 mm dia x 305 mm).
WEIGHT: 85 lbs (39 kg).
SUPPORTING TOOLS: None.
TOOL MAINTENANCE: Apply corrosion preventive oil to all surfaces
that have a black oxide finish.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing 2C15049.
FOR ALL
2C15049G02
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C15049G02
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FIXTURE, PRESSURE - COMBUSTOR AXIAL POSITION
2C15051G02
PURPOSE AND USE: To repair the dome axial dimensions after repair.
DESCRIPTION: The fixture consists of a steel base plate mounted on a
tubular steel table. A hydraulic ram is mounted on the underside of the
plate. An outer restraint ring and clamp ring attach to the base plate to
restrain the outer flange of the combustor dome. An inner restraint ring
holds the inner combustor dome flange and is mounted on an adapter plate
that travels with the hydraulic ram piston.
DIMENSIONS: 38 x 38 x 43 in. (965 x 965 x 1,092 mm).
WEIGHT: 850 lbs (386 kg).
SUPPORTING TOOLS: Hydraulic pump with a 10,000 psi (68,948 kPa) maximum.
TOOL MAINTENANCE: Apply corrosion preventive oil to all surfaces
that have a black oxide finish.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing 2C15051.
FOR ALL
2C15051G02
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C15051G02
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
KIT, MACHINE - FAN ROTOR DISK, STAGE 1
2C15057G02
PURPOSE AND USE: To machine away fretting to a specified depth so that the
pressure faces may be shimmed back to their original location.
DESCRIPTION: The kit consists of the base plate, the milling
cutter, and the gage pin.
DIMENSIONS: 35 in. dia x 3.5 in. (889 mm dia x 88.9 mm).
WEIGHT: 300 lb (136 kg).
SUPPORTING TOOLS: Used with horizontal milling machine.
TOOL MAINTENANCE: Lightly coat black oxide or black phosphate surfaces
with corrosion preventive oil.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS LIST
GROUP PART NO. NOMENCLATURE QUANTITY SUPPLIER
NUMBER CODE
G02 2C15057P02 Plate, Fixture 1
2C15057P08 Pin, Gage 1
2C15057P09 Cutter, Milling 2
FOR ALL
2C15057G02
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C15057G02
Page 2
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FIXTURE, DRILL - COMBUSTOR DOME - V-BAND
2C15059G01
FOR ALL
2C15059G01
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C15059G01
Page 2
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FIXTURE, INSPECT - LOW PRESSURE TURBINE PRESSURE COUPLING NUT
2C15060G01
PURPOSE AND USE: To hold the engine part at the thread to do an inspection
of the perpendicularity of the nut face to threads.
DESCRIPTION: The fixture consists of an expansion arbor and a master nut.
DIMENSIONS: 12 in. dia x 9 in. (305 mm dia x 229 mm).
WEIGHT: 120 lbs (54 kg).
SUPPORTING TOOLS: Rotab.
TOOL MAINTENANCE: Apply corrosion preventive oil to all surfaces
that have a black oxide finish.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing 2C15060.
FOR ALL
2C15060G01
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C15060G01
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FIXTURE, WELD - COMBUSTOR INNER/OUTER BANDS AND DOME SECTORS
2C15064G01
PURPOSE AND USE: To locate and secure the "V" bands in position
on the dome for welding.
DESCRIPTION: The tool consists of a base, a profile ring, two split clamp rings,
thirty swing clamps, two pry bars, and various screws.
DIMENSIONS: 36 in. dia x 30 in. (914 mm dia x 762 mm).
WEIGHT: 800 lb (364 kg).
SUPPORTING TOOLS: Used with TIG weld facilities.
TOOL MAINTENANCE: Lightly coat black oxide or black phosphate surfaces
with corrosion preventive oil.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: See GE drawing 2C15064.
FOR ALL
2C15064G01
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C15064G01
Page 2
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FIXTURE, INSPECT/PRETWIST - LOW PRESSURE TURBINE BLADES
2C15066G01
PURPOSE AND USE: To measure and restore the twist angle of low
pressure turbine blades.
DESCRIPTION: The fixture is a bolted steel assembly. The base plate has a
locating plate and a dovetail clamping device bolted to it.
DIMENSIONS: 12 x 25 x 16 in. (305 x 635 x 406 mm).
WEIGHT: 170 lb (77 kg).
SUPPORTING TOOLS: None.
TOOL MAINTENANCE: Lightly coat black oxide or black phosphate surfaces
with corrosion preventive oil.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: See GE drawing 2C15066.
FOR ALL
2C15066G01
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C15066G01
Page 2
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FIXTURE, WELD/MACHINE - HIGH PRESSURE TURBINE PRESSURE TUBE COUPLING NUT
2C15067G01
PURPOSE AND USE: To replace the forward (threaded) end of the high
pressure turbine pressure tube.
DESCRIPTION: The tool consists of fixturing to cut off the old end,
fixturing to permit welding the replacement end and equipment to permit
machining of the replacement end.
DIMENSIONS: 15 in. dia x 20 in. (381 mm dia x 508 mm).
WEIGHT: 50 lb (23 kg).
SUPPORTING TOOLS: Used with cut-off machine and automatic welding equipment.
TOOL MAINTENANCE: Lightly coat black oxide or black phosphate surfaces
with corrosion preventive oil.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: See GE drawing 2C15067.
FOR ALL
2C15067G01
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C15067G01
Page 2
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FIXTURE, POSITION - COMPRESSOR REAR FRAME SUMP
2C15600G01
PURPOSE AND USE: The Position Fixture is used to install the forward and
aft sumps into the compressor rear frame.
DESCRIPTION: The Position Fixture consists of a circular forward locator,
a gage block and a hoist plate with three ears attached to a circular aft
locator. The tool has a black oxide or black phosphate finish. The G01
version of 2C15600 is an alternate to the G02.
DIMENSIONS: 10 x 20 in. (254 x 508 mm).
WEIGHT: 37 lbs (17 kg).
SUPPORTING TOOLS: 2C14015, 2C6217.
TOOL MAINTENANCE: Apply corrosion preventive oil to all surfaces that
have black oxide or black phosphate coating.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing 2C15600.
FOR ALL
2C15600G01
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C15600G01
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FIXTURE, POSITION - COMPRESSOR REAR FRAME SUMP
2C15600G02
PURPOSE AND USE: The Position Fixture is used to install the forward and
aft sumps into the compressor rear frame.
DESCRIPTION: The Position Fixture consists of a circular forward locator, a gage
block and a hoist plate with three ears attached to a circular aft locator. The
tool has a black oxide or black phosphate finish. The G02 version of 2C15600 has
a new hoist plate and adds a jack screw for use with CF6-80E1 engines.
DIMENSIONS: 10 x 20 in. (254 x 508 mm).
WEIGHT: 37 lbs (17 kg).
SUPPORTING TOOLS: 2C14015, 2C6217.
TOOL MAINTENANCE: Apply corrosion preventive oil to all surfaces that
have black oxide or black phosphate coating.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing 2C15600.
FOR ALL
2C15600G02
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C15600G02
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FIXTURE, AIRFLOW - HPT BLADE, STAGE 1
2C15605G01
PURPOSE AND USE: To check the cooling air holes of the high pressure turbine
blades to assure that they are clear of foreign objects, and permit a specified
rate of air flow under specified air flow conditions.
DESCRIPTION: The fixture is a holding device for the HPT blades with a special
receptacle designed to accept, position, and retain each blade in place when
the clamp holding device is manually actuated by the operator. Four air plenum
chambers are built in the fixture. They provide the places to take air flow and
air pressure measurements for the air passages of the blades.
DIMENSIONS: 19 x 8 x 12 in. (483 x 203 x 305 mm).
WEIGHT: 80 lb (36 kg).
SUPPORTING TOOLS: Used with test stand and airflow master blade.
TOOL MAINTENANCE: Lightly coat black oxide or black phosphate surfaces
with corrosion preventive oil.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: See GE drawing 2C15605.
FOR ALL
2C15605G01
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C15605G01
Page 2
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FIXTURE, AIRFLOW - HPT BLADE, STAGE 2
2C15606G01
PURPOSE AND USE: To check the cooling air holes of the stage 2 high pressure
turbine blades to assure that they are clear of foreign objects and permit a
specified rate of air flow under specified air flow conditions.
DESCRIPTION: The fixture is a holding device for the stage 2 high pressure
turbine blades with a special receptacle to accept, position, and retain
each blade in place when the clamp holding device is manually actuated by the
operator. Four air plenum chambers are built into the fixture that provide
the locations to measure air flow and air pressure.
DIMENSIONS: 19 x 18 x 12 in. (483 x 457 x 305 mm).
WEIGHT: 40 lb (18.2 kg).
SUPPORTING TOOLS: Used with test stand and airflow master blade.
TOOL MAINTENANCE: Lightly coat black oxide or black phosphate surfaces
with corrosion preventive oil.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: See GE drawing 2C15606.
FOR ALL
2C15606G01
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C15606G01
Page 2
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FIXTURE, SIZING - COMBUSTOR INNER LINER
2C15610G01
PURPOSE AND USE: To resize the combustor inner liner during repair or overhaul.
DESCRIPTION: The fixture consists of expansion blocks, expansion
segments, and shims.
DIMENSIONS: 26 in. dia x 11 in. (660 mm dia x 279 mm).
WEIGHT: 1100 lb (500 kg).
SUPPORTING TOOLS: Used with 2C7344 expander.
TOOL MAINTENANCE: Lightly coat black oxide or black phosphate surfaces
with corrosion preventive oil.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS LIST
GROUP PART NO. NOMENCLATURE QUANTITY SUPPLIER
NUMBER CODE
G01 2C15610P02 Block, Expansion 12
2C15610P03 Segment, Upper 12
Expansion
2C15610P04 Segment, Middle 12
Expansion
2C15610P05 Segment, Lower 12
Expansion
2C15610P06 Shim, Upper 12
2C15610P07 Shim, Middle 12
2C15610P08 Shim, Lower 12
FOR ALL
2C15610G01
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C15610G01
Page 2
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FIXTURE, SIZING - COMBUSTOR OUTER LINER
2C15611G01
FOR ALL
2C15611G01
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C15611G01
Page 2
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
MASKING SET, GRIT BLAST - DOVETAIL, FAN ROTOR DISK - STAGE 1
2C15613G01
PURPOSE AND USE: To mask the stage one fan rotor disk prior to removal and
replacement of the wear coating inside the dovetail slots.
DESCRIPTION: Set consists of formed sheet metal masks, end caps, and retainer pins.
DIMENSIONS: 12 x 12 x 10 in. (305 x 305 x 254 mm).
WEIGHT: 17.5 lb (8 kg).
SUPPORTING TOOLS: Used with 2C15612 lift fixture, 2C6597 grit blasting
stand, and grit blasting equipment.
TOOL MAINTENANCE: Lightly coat black oxide or black phosphate surfaces
with corrosion preventive oil.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS LIST
GROUP PART NO. NOMENCLATURE QUANTITY SUPPLIER
NUMBER CODE
G01 2C15613P02 Mask, Right Hand 38
2C15613P03 Cap, End 76
2C15613P04 Pin, Retainer 38
2C15613P07 Mask, Left Hand 38
92391D044 Pin, Cotter 38 R
FOR ALL
2C15613G01
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C15613G01
Page 2
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FIXTURE, MACHINING - COMPRESSOR ROTOR SPOOL SHAFT FORWARD FLANGE
2C15614G01
PURPOSE AND USE: To support the high pressure compressor rotor spool
shaft while machining the forward flange.
DESCRIPTION: The fixture consists of two circular rings spaced by
eight vertical, tubular members.
DIMENSIONS: 16 in. dia x 18 in. (406 mm dia x 457 mm).
WEIGHT: 250 lb (114 kg).
SUPPORTING TOOLS: Used with standard vertical turret lathe.
TOOL MAINTENANCE: Lightly coat black oxide or black phosphate surfaces
with corrosion preventive oil.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS LIST
GROUP PART NO. NOMENCLATURE QUANTITY SUPPLIER
NUMBER CODE
G01 2C15614P02 Support 1
2C15614P03 Clamp 8
CL-3-FN Nut, Flange 8 I
CL-20-HR Ring, Hoist 3 I
FOR ALL
2C15614G01
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C15614G01
Page 2
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FIXTURE, DISTORTION REMOVAL - TURBINE REAR FRAME
2C15617G01
FOR ALL
2C15617G01
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C15617G01
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FIXTURE, MACHINE - BLOCKER DOOR HINGES
2C15619G01
PURPOSE AND USE: To position and restrain the blocker door so that the original
hinges may be removed on a vertical milling machine.
DESCRIPTION: The fixture consisting of a base, mounting plate, clamp plate,
hinge plate, arm, toggle clamps, and trunnion.
DIMENSIONS: 30 x 16 x 24 in. (762 x 406 x 610 mm).
WEIGHT: 200 lb (91 kg).
SUPPORTING TOOLS: Used with milling machine.
TOOL MAINTENANCE: Lightly coat black oxide or black phosphate surfaces
with corrosion preventive oil.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: See GE drawing 2C15619.
FOR ALL
2C15619G01
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C15619G01
Page 2
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FIXTURE, MACHINING - TRANSFER GEARBOX MAIN HOUSING
2C15620G01
PURPOSE AND USE: To machine the main gearbox housing bearing and adapter
bores before and after thermal spray.
DESCRIPTION: The fixture consists of two plates welded together. The plates mount
to a rotating table. The gearbox mounts to the vertical plate.
DIMENSIONS: 20 x 17 x 1.5 in. (508 x 432 x 38 mm).
WEIGHT: 180 lb (82 kg).
SUPPORTING TOOLS: Used with horizontal milling machine and rotating table.
TOOL MAINTENANCE: Lightly coat black oxide or black phosphate surfaces
with corrosion preventive oil.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS LIST
GROUP PART NO. NOMENCLATURE QUANTITY SUPPLIER
NUMBER CODE
G01 2C15620P02 Bracket 1
2C15620P03 Clamp 3
2C15620P04 Pin, Diamond 1
2C15620P05 Pin, Round 1
28705-5C-24B Screw, Set-Hex 3 U
LC-045H-2 Spring, Compression 3 L
FOR ALL
2C15620G01
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C15620G01
Page 2
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FIXTURE, HEAT TREAT - COMBUSTOR INNER LINER
2C15623G01
FOR ALL
2C15623G01
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C15623G01
Page 2
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FIXTURE, HOT FORM - TRAILING EDGE, STAGE 1 HPT STATOR
2C15624G01
PURPOSE AND USE: To modify the flow area of stage one high pressure
turbine nozzles with a hot form die.
DESCRIPTION: The fixture consists of a die set with a die on the top and
bottom used to form the trailing edge of the airfoils.
DIMENSIONS: 8 x 12 x 24 in. (203 x 305 x 610 mm).
WEIGHT: 180 lb (82 kg).
SUPPORTING TOOLS: Used with arbor press.
TOOL MAINTENANCE: Lightly coat black oxide or black phosphate surfaces
with corrosion preventive oil.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: See GE drawing 2C15624.
FOR ALL
2C15624G01
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C15624G01
Page 2
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FIXTURE, EDM - STAGE 1 HPT ROTOR BLADE - TIP CAVITY
2C15626G01
PURPOSE AND USE: To position the blade in an EDM machine, following tip
weld repair, for re-establishing the tip cavity.
DESCRIPTION: The fixture consists of a die set with brackets to restrain the
high pressure turbine rotor blade and the electrode.
DIMENSIONS: 9 x 12 x 12 in. (229 x 305 x 305 mm).
WEIGHT: 45 lb (20 kg).
SUPPORTING TOOLS: Used with EDM equipment.
TOOL MAINTENANCE: Lightly coat black oxide or black phosphate surfaces
with corrosion preventive oil.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: See GE drawing 2C15626.
FOR ALL
2C15626G01
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C15626G01
Page 2
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FIXTURE, EDM - STAGE 2 HPT ROTOR BLADE - TIP CAVITY
2C15627G01
PURPOSE AND USE: To position the blade in an EDM machine, following tip
weld repair, for re-establishing the tip cavity.
DESCRIPTION: The fixture consists of a die set with brackets to restrain the
high pressure turbine rotor blade and the electrode.
DIMENSIONS: 9 x 12 x 12 in. (229 x 305 x 305 mm).
WEIGHT: 45 lb (20 kg).
SUPPORTING TOOLS: Used with EDM equipment.
TOOL MAINTENANCE: Lightly coat black oxide or black phosphate surfaces
with corrosion preventive oil.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: See GE drawing 2C15627.
FOR ALL
2C15627G01
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C15627G01
Page 2
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
TEMPLATE SET - COMBUSTOR OUTER LINER PROFILE
2C15633G01
FOR ALL
2C15633G01
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C15633G01
Page 2
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FIXTURE, RESTRAINT - HEAT SHIELD, BEARING 4R AND 5R
2C15634P01
PURPOSE AND USE: To hold the heat shield for machining of diameters and surfaces.
DESCRIPTION: This fixture is a steel cylindrical assembly with a flange with
four wide slots. The fixture is painted blue enamel.
DIMENSIONS: 17 in. dia x 8 in. long (432 mm dia x 203 mm long).
WEIGHT: 130 lbs (59 kg).
SUPPORTING TOOLS: Vertical Turret Lathe (VTL).
TOOL MAINTENANCE: Apply corrosion preventive oil to all unplated
or unpainted surfaces.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing 2C15634.
FOR ALL
2C15634P01
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C15634P01
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FIXTURE, LOCATING - DEFLECTION LIMITER
2C15636G01
PURPOSE AND USE: To locate and to check the height of the deflection limiter pads
during replacement of brackets and supports. G01 is used for Airbus applications.
DESCRIPTION: The fixture is composed of right hand and left hand assemblies.
Both assemblies are composed of various lengths of aluminum square tubing
attached to each other by angle brackets.
DIMENSIONS: 13 x 13 x 96 in. (330 x 330 x 2438 mm).
WEIGHT: 60 lb (27 kg).
SUPPORTING TOOLS: None.
TOOL MAINTENANCE: Lightly coat black oxide or black phosphate surfaces
with corrosion preventive oil.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: See GE drawing 2C15636.
FOR ALL
2C15636G01
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C15636G01
Page 2
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FIXTURE, LOCATING - DEFLECTION LIMITER
2C15636G02
PURPOSE AND USE: To locate and to check the height of the deflection limiter pads
during replacement of brackets and supports. G02 is used for Boeing applications.
DESCRIPTION: The fixture is composed of right hand and left hand assemblies.
Both assemblies are composed of various lengths of aluminum square tubing
attached to each other by angle brackets.
DIMENSIONS: 13 x 13 x 96 in. (330 x 330 x 2438 mm).
WEIGHT: 60 lb (27 kg).
SUPPORTING TOOLS: None.
TOOL MAINTENANCE: Lightly coat black oxide or black phosphate surfaces
with corrosion preventive oil.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: See GE drawing 2C15636.
FOR ALL
2C15636G02
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C15636G02
Page 2
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FIXTURE, MACHINING AND INSPECTION - TURBINE REAR FRAME
2C15637G01
FOR ALL
2C15637G01
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C15637G01
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
TOOL, INSTALLATION - SELF-WRENCHING BOLTS, HIGH PRESSURE TURBINE THERMAL SHIELD
2C18053G02
PURPOSE AND USE: The Installation Tool is used to install the selfwrenching
bolts in the high pressure turbine (HPT) thermal shield.
DESCRIPTION: The Installation Tool is a modified pair of pliers with a black oxide
or black phosphate finish. The handles have a green or black plastisol coating.
DIMENSIONS: 4 x 14 x 1 (102 x 356 x 25 mm).
WEIGHT: 4 lb (2 kg).
SUPPORTING TOOLS: None.
TOOL MAINTENANCE: Apply corrosion preventive oil to all surfaces that
have black oxide or black phosphate coating.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS: Refer to drawing 2C18053.
FOR ALL
2C18053G02
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C18053G02
Page 2
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
PULLER, STATIONARY AIR/OIL SEAL - NO. 1 BEARING
2C18079G01
PURPOSE AND USE: This fixture is used to remove the No.1 bearing stationary
air/oil seal from the No. 1 bearing aft housing.
DESCRIPTION: The puller consists of the following major components: puller frame,
reaction plate, shaft, puller (radial) segments and retaining ring.
DIMENSIONS: 24 in. dia x 13 in. (610 mm dia x 330 mm).
WEIGHT: 45 lbs (21 kg).
SUPPORTING TOOLS: Overhead hoist.
TOOL MAINTENANCE: Apply corrosion preventive oil to all surfaces
that have black oxide finishing.
QUANTITY PER OPERATION: One.
REPLACEMENT PARTS LIST
GROUP PART NO. NOMENCLATURE QUANTITY SUPPLIER
NUMBER CODE
G01 2C18079P02 Frame, Puller 1
2C18079P03 Plate, Reaction 1
2C18079P04 Shaft 1
2C18079P05 Segment, Puller 3
2C18079P06 Ring, Retaining 1
2C18079P07 Nut 2
KN-2 Nut, Knurled 3
SHR-34040 Ring, Hoist 1
MS16562-223 Pin, Spring - SST 3
MS16562-252 Pin, Spring - SST 2
MS16995-95 Screw, Cap, Skt HD 2
HEX-SST
FOR ALL
2C18079G01
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR ALL
2C18079G01
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FIXTURE, INSTALLATION – ROTATING INNER SEAL RETAINER
2C18096G01
FOR B8F
2C18096G01
Page 1
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR B8F
2C18096G01
Page 2
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR B8F
2C18096G01
Page 3
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FOR B8F
2C18096G01
Page 4
Dec 01/2012
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
SECTION 5
CONTROL AND ACCESSORY TOOLING
SECTION 5 INDEX
ATA
Page Block Nomenclature Manual No.
FOR ALL
73-11-12
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
SERVO FUEL HEATER
Vendor: United Aircraft Products, Inc.
Manual: GEK 72463
Tool Number Nomenclature
FOR ALL
73-11-21
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FUEL NOZZLE ASSEMBLY
FOR ALL
73-11-41
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
Tool Number Nomenclature
FOR ALL
73-11-41
Page 2
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
COMBUSTOR DRAIN VALVE
Vendor: Fluid Regulator Inc.
Manual: GEK 85097
Tool Number Nomenclature
FOR ALL
73-11-51
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
IDG FUEL/OIL HEAT EXCHANGER
Vendor: United Aircraft Products
Manual: GEK 85011
Tool Number Nomenclature
Similar to MS33786.
FOR ALL
73-11-71
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FUEL FILTER
Vendor: Aircraft Porous Media, Inc.
Manual: GEK 28409
Tool Number Nomenclature
FOR ALL
73-12-03
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FUEL FILTER
Vendor: Aircraft Porous Media, Inc.
Manual: GEK 35585
Tool Number Nomenclature
FOR ALL
73-12-06
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
MAIN ENGINE CONTROL
WT-27553 DISASSEMBLY
WT-28455 TEST
WT-28592 DISASSEMBLY
WT-46474 ASSEMBLY
WT-46923 DISASSEMBLY
WT-46993 ASSEMBLY
WT-48347 DISASSEMBLY
WT-48351 ASSEMBLY
WT-48487 REPAIR
WT-48547 DISASSEMBLY
WT-48554 DISASSEMBLY
WT-48838 TEST
WT-48974 DISASSEMBLY
WT-49052 ASSEMBLY
WT-49228 TEST
WT-49720 ASSEMBLY
WT-49863 ASSEMBLY
WT-50284 REPAIR
WT-50987 TEST
WT-51318 ASSEMBLY
WT-51434 ASSEMBLY
WT-51443 ASSEMBLY
WT-51451 ASSEMBLY
WT-52133 REPAIR
WT-52251 TEST
WT-52266 ASSEMBLY
WT-52285 ASSEMBLY
WT-52287 ASSEMBLY
WT-52288 ASSEMBLY
WT-52289 ASSEMBLY
WT-52552 ASSEMBLY
FOR ALL
73-21-14
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
Tool Number Nomenclature
WT-52553 ASSEMBLY
WT-52577 DISASSEMBLY/ASSEMBLY
WT-53463 ASSEMBLY
WT-53470 REPAIR
WT-53918 DISASSEMBLY
WT-53963 ASSEMBLY
WT-54141 ASSEMBLY
WT-55108 ASSEMBLY
WT-55166 ASSEMBLY
WT-55413 ASSEMBLY
WT-55566 ASSEMBLY
WT-55651 ASSEMBLY
WT-55914 ASSEMBLY
WT-56080 DISASSEMBLY
WT-56081 DISASSEMBLY
WT-56082 DISASSEMBLY
WT-56086 ASSEMBLY
WT-56090 ASSEMBLY
WT-56142 TEST
WT-56311 ASSEMBLY
WT-56829 ASSEMBLY
WT-56961 DISASSEMBLY
WT-56962 DISASSEMBLY
WT-57300 ASSEMBLY
WT-57467 DISASSEMBLY
WT-58487 ASSEMBLY
WT-58488 TEST
WT-59931 TEST
WT-60462 ASSEMBLY
WT-60562 ASSEMBLY
WT-60564 ASSEMBLY
WT-60566 ASSEMBLY
WT-60598 DISASSEMBLY
WT-60603 ASSEMBLY
FOR ALL
73-21-14
Page 2
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
Tool Number Nomenclature
WT-60902 TEST
WT-61362 CHECK
WT-61458 ASSEMBLY
WT-61517 DISASSEMBLY
WT-62278 DISASSEMBLY
WT-62296 DISASSEMBLY
WT-62297 DISASSEMBLY
WT-62504 TEST
WT-63536-4 DISASSEMBLY
WT-63536-5 ASSEMBLY
WT-63536-6 TEST
WT-63536-7 TEST
WT-63536-10 TEST
WT-63536-12 DISASSEMBLY
WT-63536-14 DISASSEMBLY
WT-63824 TEST
WT-64661 TEST
WT-65212 ASSEMBLY
WT-65217 DISASSEMBLY
WT-65228 DISASSEMBLY
WT-65380 ASSEMBLY
WT-65710 ASSEMBLY
WT-65980 ASSEMBLY
WT-66162 ASSEMBLY
WT-66410 ASSEMBLY
WT-66514 ASSEMBLY
WT-66989 ASSEMBLY
WT-66999 ASSEMBLY
WT-67057 TEST
WT-67057-4 TEST
WT-67088 ASSEMBLY
WT-67400 ASSEMBLY
WT-67572 REPAIR
WT-68490 DISASSEMBLY
FOR ALL
73-21-14
Page 3
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
Tool Number Nomenclature
WT-66879 ASSEMBLY
WT-69036 ASSEMBLY
WT-69389 ASSEMBLY
WT-69737 TEST
WT-69941 ASSEMBLY
WT-81493 DISASSEMBLY
WT-82792-1 DISASSEMBLY
WT-82792-2 DISASSEMBLY
WT-82792-3 DISASSEMBLY
WT-82792-5 DISASSEMBLY
WT-82792-6 DISASSEMBLY
WT-82792-11 DISASSEMBLY
WT-82792-16 DISASSEMBLY
WT-82792-34 DISASSEMBLY
WT-82792-36 DISASSEMBLY
WT-84283-2 REPAIR
WT-84283-4 REPAIR
WT-84283-5 REPAIR
WT-84283-6 REPAIR
WT-84283-7 REPAIR
WT-84283-8 REPAIR
WT-84283-9 REPAIR
WT-84283-10 REPAIR
WT-84283-12 REPAIR
WT-84712 TEST
WT-85250 TEST
WT-85334 ASSEMBLY
WT-100518 CHECK
WT-100588 ASSEMBLY
WT-100663 TEST
WT-101015 CHECK
WT-101146 CHECK
WT-101153 TEST
WT-101325 ASSEMBLY
FOR ALL
73-21-14
Page 4
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
Tool Number Nomenclature
WT-101326 ASSEMBLY
WT-101334 ASSEMBLY
WT-101346 TEST
WT-101347 TEST
WT-101647 ASSEMBLY
WT-101648 ASSEMBLY
WT-101688 TEST
WT-101689 ASSEMBLY
WT-101832 ASSEMBLY
WT-101929 TEST
WT-102172 DISASSEMBLY
WT-102343 ASSEMBLY
WT-102418 DISASSEMBLY
WT-102578 TEST
WT-102626 ASSEMBLY
WT-102663 ASSEMBLY
WT-102669 DISASSEMBLY
WT-102673 ASSEMBLY
WT-102686 DISASSEMBLY
WT-102688 ASSEMBLY
WT-102689 ASSEMBLY
WT-102699 ASSEMBLY
WT-102758 TEST
WT-102892 TEST
WT-102899 DISASSEMBLY
WT-102903 ASSEMBLY
WT-103006 ASSEMBLY
WT-103006-1 ASSEMBLY
WT-103006-2 ASSEMBLY
WT-103043 ASSEMBLY
WT-103044 ASSEMBLY
WT-103299 ASSEMBLY
WT-103464 ASSEMBLY
WT-103562 DISASSEMBLY
FOR ALL
73-21-14
Page 5
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
Tool Number Nomenclature
WT-103612 TEST
WR-103769 TEST
WR-104071 DISASSEMBLY
WT-104256 DISASSEMBLY
WT-104260 DISASSEMBLY
WT-104260-4 DISASSEMBLY
WT-104262 DISASSEMBLY
WT-104270 ASSEMBLY
WT-104301 ASSEMBLY
WT-104316 TEST
WT-104319 DISASSEMBLY
WT-104382 DISASSEMBLY
WT-104389 TEST
WT-104575 ASSEMBLY
WT-104616 ASSEMBLY
WT-104664 DISASSEMBLY
WT-104884 ASSEMBLY
WT-104888 ASSEMBLY
WT-105386 ASSEMBLY
WT-105535 DISASSEMBLY
WT-105828 ASSEMBLY
WT-105910 TEST
WT-106115 DISASSEMBLY
WT-106157 DISASSEMBLY
WT-106161 TEST
WT-106703 TEST
WT-107166-1 ASSEMBLY
WT-107166-2 DISASSEMBLY
WT-107210 ASSEMBLY
WT-107334 DISASSEMBLY
WT-107591 TEST
WT-107647 ASSEMBLY
WT-107779 ASSEMBLY
WT-107926 ASSEMBLY
FOR ALL
73-21-14
Page 6
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
Tool Number Nomenclature
WT-108027 ASSEMBLY
WT-108079 ASSEMBLY
WT-108122 ASSEMBLY
WT-108122-1 ASSEMBLY
WT-108122-2 ASSEMBLY
WT-108387 DISASSEMBLY
WT-108430 ASSEMBLY
WT-108544 TEST
WT-108544-1 TEST
WT-108544-12 TEST
WT-108544-14 TEST
WT-108544-15 TEST
WT-108545 TEST
WT-108545-1 ASSEMBLY
WT-108545-2 TEST
WT-108545-11 TEST/ASSEMBLY
WT-108545-12 ASSEMBLY
WT-108545-13 ASSEMBLY
WT-108545-16 TEST
WT-108545-17 ASSEMBLY
WT-108545-18 ASSEMBLY
WT-108545-19 ASSEMBLY
WT-108624 DISASSEMBLY
WT-108924 ASSEMBLY
WT-108926 DISASSEMBLY/ASSEMBLY
WT-108964 ASSEMBLY
WT-109239 ASSEMBLY
WT-109579 DISASSEMBLY
WT-109630 TEST
WT-109631 DISASSEMBLY
WT-110030 ASSEMBLY
WT-110031 ASSEMBLY
WT-110052 TEST
WT-110171 TEST
FOR ALL
73-21-14
Page 7
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
Tool Number Nomenclature
WT-110171-1 TEST
WT-110171-3 TEST
WT-110171-6 TEST
WT-110171-7 TEST
WT-110175 TEST
WT-110272 ASSEMBLY
WT-110281 DISASSEMBLY
WT-110378 ASSEMBLY
WT-110387 TEST
WT-110436-1 ASSEMBLY
WT-110436-2 DISASSEMBLY/ASSEMBLY
WT-1105784 ASSEMBLY
WT-110575 ASSEMBLY
WT-110670 ASSEMBLY
WT-110692 ASSEMBLY
WT-110693 TEST
WT-110696 TEST
WT-110715 TEST/DISASSEMBLY/ASSEMBLY
WT-110747 ASSEMBLY
WT-110784 ASSEMBLY
WT-110823 TEST
WT-110868 ASSEMBLY
WT-110880 TEST
WT-110860-1 TEST
WT-110860-2 TEST
WT-110895 ASSEMBLY
WT-110895-1 ASSEMBLY
WT-110895-2 ASSEMBLY
WT-110895-3 ASSEMBLY
WT-110895-5 ASSEMBLY
WT-110895-6 ASSEMBLY
WT-110895-7 ASSEMBLY
WT-110895-8 ASSEMBLY
WT-110895-12 ASSEMBLY
FOR ALL
73-21-14
Page 8
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
Tool Number Nomenclature
WT-110990 ASSEMBLY
WT-110994 ASSEMBLY
WT-110994-1 ASSEMBLY
WT-110994-2 ASSEMBLY
WT-111011 ASSEMBLY
WT-111022 TEST
WT-111135 ASSEMBLY
WT-111140-1 ASSEMBLY
WT-111140-2 ASSEMBLY
WT-111212 TEST
WT-111230 DISASSEMBLY
WT-111273 DISASSEMBLY
WT-111557 ASSEMBLY
WT-111558 ASSEMBLY
WT-111559 ASSEMBLY
WT-111559-5 ASSEMBLY
WT-111692 ASSEMBLY
WT-111692-1 ASSEMBLY
WT-111692-3 ASSEMBLY
WT-111692-8 ASSEMBLY
WT-111692-9 ASSEMBLY
WT-111775 DISASSEMBLY
WT-111852 ASSEMBLY
WT-111873 DISASSEMBLY
WT-112163 TEST
WT-112230 TEST
WT-112233-1 ASSEMBLY
WT-112233-2 ASSEMBLY
WT-112233-3 ASSEMBLY
WT-112233-4 ASSEMBLY
WT-112233-5 ASSEMBLY
WT-112252 TEST
WT-112426 ASSEMBLY
WT-112433 DISASSEMBLY
FOR ALL
73-21-14
Page 9
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
Tool Number Nomenclature
WT-112441 ASSEMBLY
WT-112481 ASSEMBLY
WT-112489 ASSEMBLY
WT-112516 ASSEMBLY
WT-112654-2 ASSEMBLY
WT-112682-1 ASSEMBLY
WT-112682-2 ASSEMBLY
WT-112685 ASSEMBLY
WT-112703 ASSEMBLY
WT-112800 ASSEMBLY
WT-112801 ASSEMBLY
WT-112803-1 ASSEMBLY
WT-112803-2 ASSEMBLY
WT-112807 ASSEMBLY
WT-112808 ASSEMBLY
WT-112825 TEST
WT-112842 TEST
WT-112843 TEST
WT-112854 TEST
WT-112874 TEST
WT-112875 TEST
WT-112906 ASSEMBLY
WT-112958 TEST
WT-113175 TEST
WT-113284 ASSEMBLY
WT-113285 ASSEMBLY
WT-113286 ASSEMBLY
WT-113330 TEST
WT-113404 ASSEMBLY
WT-113492 TEST
WT-113729 ASSEMBLY
WT-113740 TEST
WT-113755 ASSEMBLY
WT-113779 ASSEMBLY
FOR ALL
73-21-14
Page 10
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
Tool Number Nomenclature
WT-113892 ASSEMBLY
WT-113915 TEST
WT-114097 TEST
WT-114181 DISASSEMBLY
WT-114215 ASSEMBLY
WT-114219 ASSEMBLY
WT-114275 ASSEMBLY
WT-114486 ASSEMBLY
WT-115054 ASSEMBLY
FOR ALL
73-21-14
Page 11
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
MAIN ENGINE CONTROL
Vendor: Woodward Governor Co.
Manual: GEK 92546
Tool Number Nomenclature
To be supplied.
FOR ALL
73-21-16
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
CIT SENSOR
Vendor: Woodward Governor Co.
Manual: GEK 92547
Tool Number Nomenclature
FOR ALL
73-21-22
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
MAIN ENGINE CONTROL
Vendor: Woodward Governor Co.
Manual: GEK 92792
Tool Number Nomenclature
To be supplied.
FOR ALL
73-21-27
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
POWER MANAGEMENT CONTROL
Vendor: General Electric Company
Manual: GEK 92535
Tool Number Nomenclature
To be supplied.
FOR ALL
73-21-33
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
POWER MANAGEMENT CONTROL
Vendor: General Electric Company
Manual: GEK 95445
Tool Number Nomenclature
To be supplied.
FOR ALL
73-21-34
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
T2 SENSOR
Vendor: Woodward Governor Company.
Manual: GEK 92458
Tool Number Nomenclature
FOR ALL
73-21-42
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
N1 SENSOR
Vendor: Woodward Governor Company
Manual: GEK 92530
Tool Number Nomenclature
WT-53963 ASSEMBLY
WT-54312 ASSEMBLY
WT-62246 TESTING AND FAULT ISOLATION
WT-82792-1 DISASSEMBLY
WT-85334 TESTING AND FAULT ISOLATION
WT-85485 TESTING AND FAULT ISOLATION
WT-103562 DISASSEMBLY/ASSEMBLY
WT-107592 TESTING AND FAULT ISOLATION
WT-110777 ASSEMBLY
WT-110823 ASSEMBLY
WT-112211-1 ASSEMBLY
WT-112211-2 ASSEMBLY
WT-112341 DISASSEMBLY/ASSEMBLY
WT-112415 DISASSEMBLY
WT-112416 DISASSEMBLY
WT-113871 TESTING AND FAULT ISOLATION
WT-115067 DISASSEMBLY
FOR ALL
73-21-51
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
ELECTRICAL CABLES
Vendor: General Electric Company
Manual: GEK 92536
Tool Number Nomenclature
No special tools.
FOR ALL
73-21-73
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
INLET TEMPERATURE SENSOR
Vendor: Rosemount Inc.
Manual: GEK 97266
Tool Number Nomenclature
No special tools.
FOR ALL
73-21-92
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FUEL FLOW TRANSMITTER
Vendor: General Electric Company
Manual: GEK 92510
Tool Number Nomenclature
FOR ALL
73-31-11
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
IGNITION EXCITER
Vendor: Bendix Corporation
Manual: GEK 85091
Tool Number Nomenclature
FOR ALL
74-11-12
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
IGNITION LEAD
Vendor: Bendix Corporation
Manual: GEK 92499
Tool Number Nomenclature
FOR ALL
74-21-08
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
IGNITION LEAD
Vendor: Bendix Corporation
Manual: GEK 85090
Tool Number Nomenclature
FOR ALL
74-21-13
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
IGNITION LEAD
Vendor: Bendix Corporation
Manual: GEK 92473
Tool Number Nomenclature
FOR ALL
74-21-16
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
IGNITER PLUG
Vendor: Bendix Corporation
Manual: GEK 92474
Tool Number Nomenclature
FOR ALL
74-21-33
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
IGNITER PLUG
Vendor: Bendix Corporation
Manual: GEK 92490
Tool Number Nomenclature
FOR ALL
74-21-34
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
IGNITER PLUG
Vendor: Champion Corporation
Manual: GEK 97268
Tool Number Nomenclature
FOR ALL
74-21-38
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
COOLING AIR VALVE
Vendor: Parker Hannifin Corporation
Manual: GEK 92475
Tool Number Nomenclature
FOR ALL
75-24-16
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
ACTIVE CLEARANCE CONTROL SIGNAL VALVE ASSEMBLY
Vendor: General Electric Company
Manual: GEK 92516
Tool Number Nomenclature
No special tooling.
FOR ALL
75-24-22
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
VSV FEEDBACK CABLE
Vendor: Cablecraft, Inc.
Manual: GEK 50449
Tool Number Nomenclature
T-397-1 CLAMP
T-397-2 CLAMP
T-397-3 CLAMP
T-397-4 ROD END BEARING
T-109-250 SWAGING DIE
T-109-260 SWAGING DIE
T-396 STAKING TOOL
T-399 DIE SET
561-090-001 PROTECTIVE COVER
T-109-174 SWAGING DIE
T-919 VISE GRIP WITH SPECIAL JAWS
T-1227 TEST FIXTURE
MIL-T-6117 SPECIFICATION
FOR ALL
75-31-11
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
VSV ACTUATOR
Vendor: Arkwin Industries, Inc.
Manual: GEK 50446
Tool Number Nomenclature
T1334-2 WRENCH
T1334-4 STACKING TOOL
T1334-5 INSTALLATION TOOL
T1334-6 ID ASSEMBLY TOOL
T1334-7 ID ASSEMBLY TOOL CARRIER
T1334-8 RING COMPRESSION TOOL
T1334-9 CHECKING FIXTURE
T1334-11 TEST ADAPTER
T1347-3 HOLDING FIXTURE
FOR ALL
75-31-31
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
VSV FEEDBACK CABLE
Vendor: Cablecraft, Inc.
Manual: GEK 50450
Tool Number Nomenclature
T-397-1 CLAMP
T-397-2 CLAMP
T-397-3 CLAMP
T-397-4 ROD END BEARING
T-397-5 ROD END BEARING
T-109-250 SWAGING DIE
T-109-260 SWAGING DIE
T-396 STAKING TOOL
T-399 DIE SET
561-090-001 PROTECTIVE COVER
T-109-174 SWAGING DIE
T-919 VISE GRIP WITH SPECIAL JAWS
MIL-T-6117 SPECIFICATION
T-970 TEST FIXTURE
FOR ALL
75-32-11
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
VSV ACTUATOR
Vendor: Arkwin Industries, Inc.
Manual: GEK 92476
Tool Number Nomenclature
FOR ALL
75-32-21
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
DISPLACEMENT TRANSDUCER
Vendor: Gulton Industries, Inc.
Manual: GEK 35566
Tool Number Nomenclature
FOR ALL
75-42-02
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
POSITION INDICATING SWITCH
Vendor: Westport International
Manual: GEK 85054
Tool Number Nomenclature
FOR ALL
75-44-11
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
THROTTLE GEARBOX ASSEMBLY
Vendor: Controlex/Eanco
Manual: GEK 92524
Tool Number Nomenclature
To be supplied.
FOR ALL
76-10-02
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FAN SPEED SENSOR
Vendor: General Electric-Wilmington
Manual: GEK 92508
Tool Number Nomenclature
FOR ALL
77-12-12
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
ALTERNATOR
Vendor: General Electric Company
Manual: GEK 50452
Tool Number Nomenclature
No special tools.
FOR ALL
77-12-21
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
ALTERNATING CURRENT GENERATOR
Vendor: Pacific Scientific
Manual: GEK 92531
Tool Number Nomenclature
To be supplied.
FOR ALL
77-12-23
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
THERMOCOUPLE CABLES, LEAD AND JUNCTION BOX
Vendor: Revere Corp.
Manual: GEK 92511
Tool Number Nomenclature
No special tools.
FOR ALL
77-21-14
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
THERMOCOUPLE PROBE
Vendor: General Electric-Wilmington
Manual: GEK 92537
Tool Number Nomenclature
FOR ALL
77-21-41
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
VIBRATION TRANSDUCER
Vendor: Vibro-meter Corp.
Manual: GEK 92489
Tool Number Nomenclature
FOR ALL
77-31-25
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
VIBRATION TRANSDUCER
Vendor: Vibro-meter Corp.
Manual: GEK 92506
Tool Number Nomenclature
FOR ALL
77-31-26
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
VIBRATION TRANSDUCER
Vendor: Vibro-meter Corp.
Manual: GEK 92507
Tool Number Nomenclature
FOR ALL
77-31-27
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
ENGINE DATA MULTIPLIER
Vendor: Hamilton Standard
Manual: GEK 92517
Tool Number Nomenclature
FOR ALL
77-32-02
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
ENGINE SERIAL NUMBER PLUG
Vendor: Hamilton Standard
Manual: GEK 92518
Tool Number Nomenclature
No special tools.
FOR ALL
77-32-04
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
VBV ELECTRICAL CABLE
Vendor: General Electric Company
Manual: GEK 92512
Tool Number Nomenclature
No special tools.
FOR ALL
77-34-02
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
PRESSURE PROBE EGT PROBE PLUG
Vendor: General Electric-Wilmington
Manual: GEK 92539
Tool Number Nomenclature
FOR ALL
77-34-16
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
PMUX ELECTRICAL CABLE
Vendor: General Electric Company
Manual: GEK 92513
Tool Number Nomenclature
No special tools.
FOR ALL
77-34-17
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
T3 SENSOR COMPRESSOR OUTLET TEMPERATURE
Vendor: General Electric Company
Manual: GEK 92538
Tool Number Nomenclature
No special tools.
FOR ALL
77-34-22
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
PLANE 5 PROBE
Vendor: General Electric Company
Manual: GEK 95446
Tool Number Nomenclature
No special tools.
FOR ALL
77-34-24
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
ADJUSTA-KEEPER ASSEMBLY
Vendor: Hartwell Corporation
Manual: GEK 85036
Tool Number Nomenclature
No special tools.
FOR ALL
78-30-02
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
CABLE, ELECTRICAL, FAN REVERSER
Vendor: General Electric Company
Manual: GEK 92514
Tool Number Nomenclature
No special tools.
FOR ALL
78-31-35
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FAN REVERSER
Vendor: General Electric Company
Manual: GEK 92466
Tool Number Nomenclature
FOR ALL
78-32-00
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
TOGGLE HOOK LATCH ASSEMBLY
Vendor: Hartwell Corporation
Manual: GEK 85033
Tool Number Nomenclature
No special tools.
FOR ALL
78-32-18
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
TOGGLE HOOK LATCH ASSEMBLY
Vendor: Hartwell Corporation
Manual: GEK 85034
Tool Number Nomenclature
No special tools.
FOR ALL
78-32-19
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
CENTER DRIVE UNIT
Vendor: Garrett Corporation
Manual: GEK 92534
Tool Number Nomenclature
FOR ALL
78-32-23
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
CHECK VALVE
Vendor: Garrett Corporation
Manual: GEK 92505
Tool Number Nomenclature
FOR ALL
78-32-25
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
THROTTLE FEEDBACK GEARBOX
Vendor: Garrett Corporation
Manual: GEK 92486
Tool Number Nomenclature
FOR ALL
78-32-27
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
VALVE, CORE COWL INTERLOCK
Vendor: Arkwin Industries, Inc.
Manual: GEK 92480
Tool Number Nomenclature
FOR ALL
78-36-31
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
OIL TANK
Vendor: General Electric Company
Manual: GEK 50441
Tool Number Nomenclature
No special tools.
FOR ALL
79-11-11
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
LUBE AND SCAVENGE PUMP
Vendor: Lear Siegler, Inc.
Manual: GEK 92494
Tool Number Nomenclature
FOR ALL
79-21-13
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
SCAVENGE OIL FILTER
Vendor: Aircraft Porous Media, Inc.
Manual: GEK 28420
Tool Number Nomenclature
FOR ALL
79-22-01
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
HEAT EXCHANGER
Vendor: Garrett Corporation
Manual: GEK 50442
Tool Number Nomenclature
FOR ALL
79-22-22
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
OIL LEVEL SENSOR
Vendor: General Electric Company
Manual: GEK 92509
Tool Number Nomenclature
FOR ALL
79-31-02
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
FUEL PRESSURE TRANSMITTER
Vendor: Armtec Industries
Manual: GEK 92479
Tool Number Nomenclature
FOR ALL
79-31-41
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
OIL PRESSURE TRANSMITTER
Vendor: Armtec Industries
Manual: GEK 95444
Tool Number Nomenclature
FOR ALL
79-31-65
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
OIL PRESSURE TRANSMITTER
Vendor: Armtec Industries
Manual: GEK 95443
Tool Number Nomenclature
FOR ALL
79-31-69
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
PNEUMATIC SHUTOFF VALVE
Vendor: Garrett Corporation
Manual: GEK 97267
Tool Number Nomenclature
FOR ALL
80-11-09
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
STARTER
Vendor: Garrett Corporation
Manual: GEK 50443
Tool Number Nomenclature
FOR ALL
80-11-11
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
Tool Number Nomenclature
FOR ALL
80-11-11
Page 2
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
STARTER
Vendor: Hamilton Standard Co.
Manual: GEK 50458
Tool Number Nomenclature
FOR ALL
80-11-12
Page 1
Feb 28/2005
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page
CF6-80C2
ILLUSTRATED TOOL AND EQUIPMENT
MANUAL
STANDARD EQUIPMENT SUPPLIER CODE
TOOL NUMBER SUPPLIER
A Avibank Manufacturing, Inc.
210 South Victory Blvd.
Burbank, CA 91503
B B.K. Sweeney Company
6300 Stapleton South Drive
Denver, CO 80216
C Reid Tool Supply Co.
2233 Temple
Muskegon Heights, MI 49444
D Enerpac Division
Applied Power Industry
13000 West Silver Springs Drive
Butler, WI 53007
E Vlier Engineering Corp.
2333 Valley Street
Burbank, CA 91505
F Jergens, Inc.
19520 Nottingham Road
Cleveland, OH 44110
G Barnes Group Inc.
123 Main Street
Bristol, CT 06010
H Boston Gear Works
14 Hayward Street
Quincy, MA 02171
I Carr Lane Manufacturing Co.
4200 Carr Lane Court
St. Louis, MO 63119
J Waldes Kohinoor, Inc.
Dept. 031 Austel Place
Long Island City, NY 11101
K Parker Seal Co.
Parker-Hannifin Corp.
Lexington, KY 40509
L Lee Spring Co.
28 Main Street
Brooklyn, NY 11201
M Pic Design Corp.
Benson Road
P.O. Box 1004
Ridgefield, CT 06762