Professional Documents
Culture Documents
TABLE OF
CONTENTS.
04 VOLUME CONTROL DAMPERS
98 SPIN IN DAMPERS
2 Right to alterations reserved. SAFID is a registered trademark. © Copyright 2018. All rights reserved Right to alterations reserved. SAFID is a registered trademark. © Copyright 2018. All rights reserved 3
VOLUME
CONTROL
DAMPERS
VOLUME CONTROL DAMPERS
Air Performance
Pressure Drop
The tests for pressure prop of Volume Control Dampers were conducted as per ANSI / AMCA Standard 500-D, Figure 5.3
which simulate the actual site condition when installed in ventilation, supply and return air conditioning ductworks.
The SPK 30 dampers are ruggedly built dampers with a SPK 30 - 110 Pressure Drop at Face Area Velocity
casing of robust assembly, formed from channel frame General construction as type SPK 30 - 100 damper but with
for flanged connection to ductwork. The blades are blades, shafts and blade to shaft fixing are from stainless
formed single skin and reinforced with longitudinal steel Grade 304.
305 x 305 610 x 610 914 x 914 305 x 1219 1219 x 305
structurally designed triple vee shape.
Optional: Blades from stainless steel Grade 316 or 316L. 12 in. x 12 in. 24 in. x 24 in. 36 in. x 36 in. 12 in. x 48 in. 48 in. x 12 in.
Blade’s action can be opposed blades or parallel Pressure Pressure Pressure Pressure Pressure
Velocity Velocity Velocity Velocity Velocity
SPK 30 - 120 Drop Drop Drop Drop Drop
blades. (FPM) (FPM) (FPM) (FPM) (FPM)
General construction as type SPK 30 - 100 damper but (in. W.G) (in. W.G) (in. W.G) (in. W.G) (in. W.G)
with frame, blades, linkage, case bearing, axles and control
shaft are from stainless steel Grade 304. 1519 0.065 2000 0.079 2494 0.110 7706 1.899 7713 1.957
Standard Construction 1262 0.046 1752 0.060 1991 0.068 7075 1.585 7079 1.650
Optional: Frame and blades from stainless steel Grade 316 1006 0.030 1497 0.044 1494 0.035 6049 1.139 6042 1.156
Frame: or 316L.
755 0.022 1001 0.020 994 0.016 4016 0.500 4015 0.492
VOLUME CONTROL DAMPERS
Blades:
250mm max. width, 1.5mm (16 Ga.) galvanized steel. Note:
Extrapolation below the minimum test static pressure drop shall be permitted as per AMCA 511-10,
Finish: Section 13.2.1.1. The air performance shall not be extrapolated more than 50% of the static pressure
Mill Galvanized range of test downward.
Linkage:
Side linkage concealed in frame for parallel and
Catalog ID: SPK 30 - 100 September 30, 2013
opposed blade operation.
SAFID certifies that the Volume Control Damper shown herein is SAFID certifies that the Volume Control Damper shown herein is
Case Bearing: licensed to bear the AMCA Seal for Model SPK 30-100-OB-
S-B-R. The ratings shown are based on tests and procedures
licensed to bear the AMCA Seal for Model SPK 30-100-OB-
S-B-R. The ratings shown are based on tests and procedures
Brass bearing as standard. performed in accordance with AMCA Publication 511 and performed in accordance with AMCA Publication 511 and
comply with the requirements of the AMCA Certified Ratings comply with the requirements of the AMCA Certified Ratings
Sintered bronze oilite (optional). Program. Program.
The AMCA Certified Ratings Seal applies to Air Performance The AMCA Certified Ratings Seal applies to Air Performance
Ratings. Ratings.
Control Shaft: Test Information Test Information
Tested for air performance in accordance with ANSI / AMCA Tested for air performance in accordance with ANSI / AMCA
12mm diameter zinc plated mild steel. Standard 500-D-07 (Pressure Drop), Figure 5.3. Standard 500-D-07 (Pressure Drop), Figure 5.3. Catalog ID: SPK 30 - 100 September 30, 2013
6 Right to alterations reserved. SAFID is a registered trademark. © Copyright 2018. All rights reserved Right to alterations reserved. SAFID is a registered trademark. © Copyright 2018. All rights reserved 7
FLANGE TYPE VOLUME CONTROL DAMPER FLANGE TYPE VOLUME CONTROL DAMPER
SPK 30 SERIES [SPK 30 - 100, SPK 30 - 110, SPK 30 - 120] SPK 30 SERIES [SPK 30 - 100, SPK 30 - 110, SPK 30 - 120]
Pressure Drop at Face Area Velocity Pressure Drop at Face Area Velocity
Damper Size 12 in. x 12 in. - Fully Open Blades Damper Size 24 in. x 24 in. - Fully Open Blades
VOLUME CONTROL DAMPERS
8 Right to alterations reserved. SAFID is a registered trademark. © Copyright 2018. All rights reserved Right to alterations reserved. SAFID is a registered trademark. © Copyright 2018. All rights reserved 9
FLANGE TYPE VOLUME CONTROL DAMPER FLANGE TYPE VOLUME CONTROL DAMPER
SPK 30 SERIES [SPK 30 - 100, SPK 30 - 110, SPK 30 - 120] SPK 30 SERIES [SPK 30 - 100, SPK 30 - 110, SPK 30 - 120]
Pressure Drop at Face Area Velocity Pressure Drop at Face Area Velocity
Damper Size 36 in. x 36 in. - Fully Open Blades Damper Size 12 in. x 48 in. - Fully Open Blades
VOLUME CONTROL DAMPERS
10 Right to alterations reserved. SAFID is a registered trademark. © Copyright 2018. All rights reserved Right to alterations reserved. SAFID is a registered trademark. © Copyright 2018. All rights reserved 11
FLANGE TYPE VOLUME CONTROL DAMPER FLANGE TYPE VOLUME CONTROL DAMPER
SPK 30 SERIES [SPK 30 - 100, SPK 30 - 110, SPK 30 - 120] SPK 30 SERIES [SPK 30 - 100, SPK 30 - 110, SPK 30 - 120]
100 100 1
160 160
150 150 1
200 200 1
VOLUME CONTROL DAMPERS
12 Right to alterations reserved. SAFID is a registered trademark. © Copyright 2018. All rights reserved Right to alterations reserved. SAFID is a registered trademark. © Copyright 2018. All rights reserved 13
MATERIALS CONSTRUCTION INSTALLATION DETAILS
SPK 30 SERIES [SPK 30 - 100, SPK 30 - 110, SPK 30 - 120] SPK 30 SERIES [SPK 30 - 100, SPK 30 - 110, SPK 30 - 120]
Axle and Drive Shaft Fixing Details Damper with Control Option Type A Damper to Slide on Flange Connection Damper to Angle Flange Connection
Type S1 Type S2 (Stainless Steel Type 304) Width Height No. of Holes No. of Holes
(mm) (mm) W Dim. H Dim.
100 100 1 2
150 150 2 2
200 200 2 2
2
VOLUME CONTROL DAMPERS
300 400 3 4
350 500 3 5
400 600 4 6
450 700 4 6
500 800 4 7
550 900 4 8
600 1000 5 9
650 1100 5 10
700 1200 6 10
750 1300 6 11
800 1400 7 12
850 1500 7 13
14 Right to alterations reserved. SAFID is a registered trademark. © Copyright 2018. All rights reserved Right to alterations reserved. SAFID is a registered trademark. © Copyright 2018. All rights reserved 15
PRODUCT RANGE ORDER REFERENCE DETAILS
SPK 30 SERIES [SPK 30 - 100, SPK 30 - 110, SPK 30 - 120] SPK 30 SERIES [SPK 30 - 100, SPK 30 - 110, SPK 30 - 120]
Note:
Catalog ID: SPK 30 - 100 September 30, 2013 Contact SAFID for technical data sheet of actuators. Catalog ID: SPK 30 - 100 September 30, 2013
16 Right to alterations reserved. SAFID is a registered trademark. © Copyright 2018. All rights reserved Right to alterations reserved. SAFID is a registered trademark. © Copyright 2018. All rights reserved 17
FLANGE TYPE VOLUME CONTROL DAMPER FLANGE TYPE VOLUME CONTROL DAMPER
WITH EXTRUDED ALUMINUM AIRFOIL BLADES WITH EXTRUDED ALUMINUM AIRFOIL BLADES
Air Performance
Pressure Drop
Standard Construction
Frame:
160mm x 30mm x 1.5mm (16 Ga.) galvanized steel formed
channel for flange connection.
Blades:
VOLUME CONTROL DAMPERS
Finish:
Frame of mill galvanized.
Blades of mill aluminum.
Linkage:
Galvanized steel side linkage concealed in frame for
parallel or opposed blade operation.
Hard PVC gear side linkage for opposed blade operation. Catalog ID: SPK 30 - 300 December 19, 2013
Case Bearing:
SAFID certifies that the Volume Control Damper shown herein is SAFID certifies that the Volume Control Damper shown herein is
Brass bearing as standard. licensed to bear the AMCA Seal for Model SPK 30-300-OB- licensed to bear the AMCA Seal for Model SPK 30-300-OB-
Sintered bronze oilite (optional). S-B-R. The ratings shown are based on tests and procedures S-B-R. The ratings shown are based on tests and procedures
performed in accordance with AMCA Publication 511 and performed in accordance with AMCA Publication 511 and
Hard PVC gear integrated with 12mm x 12mm axle for comply with the requirements of the AMCA Certified Ratings comply with the requirements of the AMCA Certified Ratings
opposed blade operation only. Program. Program.
The AMCA Certified Ratings Seal applies to Air Performance The AMCA Certified Ratings Seal applies to Air Performance
Ratings. Ratings.
Test Information Test Information
Control Shaft: Tested for air performance in accordance with ANSI / AMCA Tested for air performance in accordance with ANSI / AMCA
12mm square or round zinc plated mild steel. Standard 500-D-07 (Pressure Drop), Figure 5.3. Standard 500-D-07 (Pressure Drop), Figure 5.3. Catalog ID: SPK 30 - 300 December 19, 2013
18 Right to alterations reserved. SAFID is a registered trademark. © Copyright 2018. All rights reserved Right to alterations reserved. SAFID is a registered trademark. © Copyright 2018. All rights reserved 19
FLANGE TYPE VOLUME CONTROL DAMPER FLANGE TYPE VOLUME CONTROL DAMPER
WITH EXTRUDED ALUMINUM AIRFOIL BLADES WITH EXTRUDED ALUMINUM AIRFOIL BLADES
SPK 30 SERIES [SPK 30 - 300, SPK 30 - 310] SPK 30 SERIES [SPK 30 - 300, SPK 30 - 310]
Pressure Drop at Face Area Velocity Pressure Drop at Face Area Velocity
Damper Size 24 in. x 24 in. - Fully Open Blades Damper Size 36 in. x 36 in. - Fully Open Blades
VOLUME CONTROL DAMPERS
20 Right to alterations reserved. SAFID is a registered trademark. © Copyright 2018. All rights reserved Right to alterations reserved. SAFID is a registered trademark. © Copyright 2018. All rights reserved 21
FLANGE TYPE VOLUME CONTROL DAMPER FLANGE TYPE VOLUME CONTROL DAMPER
WITH EXTRUDED ALUMINUM AIRFOIL BLADES WITH EXTRUDED ALUMINUM AIRFOIL BLADES
SPK 30 SERIES [SPK 30 - 300, SPK 30 - 310] SPK 30 SERIES [SPK 30 - 300, SPK 30 - 310]
Pressure Drop at Face Area Velocity Pressure Drop at Face Area Velocity
Damper Size 12 in. x 48 in. - Fully Open Blades Damper Size 48 in. x 12 in. - Fully Open Blades
VOLUME CONTROL DAMPERS
22 Right to alterations reserved. SAFID is a registered trademark. © Copyright 2018. All rights reserved Right to alterations reserved. SAFID is a registered trademark. © Copyright 2018. All rights reserved 23
MATERIALS CONSTRUCTION INSTALLATION DETAILS
SPK 30 SERIES [SPK 30 - 300, SPK 30 - 310] SPK 30 SERIES [SPK 30 - 300, SPK 30 - 310]
Axle & Drive Shaft Fixing Details Mounting Bracket for Actuator
300 300 3 3
4
VOLUME CONTROL DAMPERS
400 400 4 4
500 400 4 4
600 400 5 4
500 500 4 4
600 500 5 4
700 500 6 4
700 600 6 5
800 600 7 5
700 700 6 6
800 700 7 6
900 700 8 6
800 800 7 7
900 800 8 7
900 900 8 8
Catalog ID: SPK 30 - 300 September 30, 2013 Catalog ID: SPK 30 - 300 December 19, 2013
24 Right to alterations reserved. SAFID is a registered trademark. © Copyright 2018. All rights reserved Right to alterations reserved. SAFID is a registered trademark. © Copyright 2018. All rights reserved 25
PRODUCT RANGE ORDER REFERENCE DETAILS
SPK 30 SERIES [SPK 30 - 300, SPK 30 - 310] SPK 30 SERIES [SPK 30 - 300, SPK 30 - 310]
Construction Variants Description A12 NF24 US Spring-return * - Stands for Standard Supply
Note:
Catalog ID: SPK 30 - 300 December 19, 2013 Contact SAFID for technical data sheet of actuators. Catalog ID: SPK 30 - 300 December 19, 2013
26 Right to alterations reserved. SAFID is a registered trademark. © Copyright 2018. All rights reserved Right to alterations reserved. SAFID is a registered trademark. © Copyright 2018. All rights reserved 27
FLANGE TYPE VCD WITH EXTRUDED FLANGE TYPE VCD WITH EXTRUDED
ALUMINUM AIRFOIL BLADES ALUMINUM AIRFOIL BLADES
28 Right to alterations reserved. SAFID is a registered trademark. © Copyright 2018. All rights reserved Right to alterations reserved. SAFID is a registered trademark. © Copyright 2018. All rights reserved 29
FLANGE TYPE VCD WITH EXTRUDED FLANGE TYPE VCD WITH EXTRUDED
ALUMINUM AIRFOIL BLADES ALUMINUM AIRFOIL BLADES
SPK 30 SERIES [SPK 30 - 300L, SPK 30 - 310L] SPK 30 SERIES [SPK 30 - 300L, SPK 30 - 310L]
12 in. x 12 in. 24 in. x 24 in. 36 in. x 36 in. 12 in. x 48 in. 48 in. x 12 in.
305 x 305 610 x 610 914 x 914 305 x 1219 1219 z 305
1519 0.076 1500 0.019 1502 0.015 6059 0.398 6061 0.942
1263 0.052 1249 0.013 1246 0.009 5007 0.266 5023 0.633
1006 0.033 1000 0.009 997 0.006 4044 0.181 4053 0.416
755 0.020 746 0.006 748 0.004 3000 0.093 3018 0.223
VOLUME CONTROL DAMPERS
SAFID certifies that the Low Leakage Volume Control Damper shown SAFID certifies that the Low Leakage Volume Control Damper shown
herein is licensed to bear the AMCA Seal for Model SPK 30-300L. herein is licensed to bear the AMCA Seal for Model SPK 30-300L.
The ratings shown are based on tests and procedures performed The ratings shown are based on tests and procedures performed
in accordance with AMCA Publication 511 and comply with the in accordance with AMCA Publication 511 and comply with the
requirements of the AMCA Certified Ratings Program. The AMCA requirements of the AMCA Certified Ratings Program. The AMCA
Certified Ratings Seal applies to Air Leakage and Air Performance Certified Ratings Seal applies to Air Leakage and Air Performance
Ratings. Ratings.
Test Information: Tested for air leakage in accordance with ANSI Test Information: Tested for air leakage in accordance with ANSI
/ AMCA Standard 500-D-07, Figure 5.4. Air leakage is based on / AMCA Standard 500-D-07, Figure 5.4. Air leakage is based on
operation between 32 ºF and 120 ºF. Tested for air performance in operation between 32 ºF and 120 ºF. Tested for air performance in
accordance with ANSI / AMCA Standard 500-D-07 (Pressure Drop), accordance with ANSI / AMCA Standard 500-D-07 (Pressure Drop),
Figure 5.3. Figure 5.3.
Only 100mm blade width and opposed blade action is AMCA certified. Catalog ID: SPK 30 - 300L December 18, 2013 Only 100mm blade width and opposed blade action is AMCA certified. Catalog ID: SPK 30 - 300L December 18, 2013
30 Right to alterations reserved. SAFID is a registered trademark. © Copyright 2018. All rights reserved Right to alterations reserved. SAFID is a registered trademark. © Copyright 2018. All rights reserved 31
FLANGE TYPE VCD WITH EXTRUDED FLANGE TYPE VCD WITH EXTRUDED
ALUMINUM AIRFOIL BLADES ALUMINUM AIRFOIL BLADES
SPK 30 SERIES [SPK 30 - 300L, SPK 30 - 310L] SPK 30 SERIES [SPK 30 - 300L, SPK 30 - 310L]
Pressure Drop at Face Area Velocity Pressure Drop at Face Area Velocity
Damper Size 24 in. x 24 in. - Fully Open Blades Damper Size 36 in. x 36 in. - Fully Open Blades
VOLUME CONTROL DAMPERS
32 Right to alterations reserved. SAFID is a registered trademark. © Copyright 2018. All rights reserved Right to alterations reserved. SAFID is a registered trademark. © Copyright 2018. All rights reserved 33
FLANGE TYPE VCD WITH EXTRUDED FLANGE TYPE VCD WITH EXTRUDED
ALUMINUM AIRFOIL BLADES ALUMINUM AIRFOIL BLADES
SPK 30 SERIES [SPK 30 - 300L, SPK 30 - 310L] SPK 30 SERIES [SPK 30 - 300L, SPK 30 - 310L]
Pressure Drop at Face Area Velocity Pressure Drop at Face Area Velocity
Damper Size 12 in. x 48 in. - Fully Open Blades Damper Size 48 in. x 12 in. - Fully Open Blades
VOLUME CONTROL DAMPERS
34 Right to alterations reserved. SAFID is a registered trademark. © Copyright 2018. All rights reserved Right to alterations reserved. SAFID is a registered trademark. © Copyright 2018. All rights reserved 35
FLANGE TYPE VCD WITH EXTRUDED
MATERIALS CONSTRUCTION
ALUMINUM AIRFOIL BLADES
SPK 30 SERIES [SPK 30 - 300L, SPK 30 - 310L] SPK 30 SERIES [SPK 30 - 300L, SPK 30 - 310L]
Dimensions
Drive Shaft Mounting Bracket
1 - Casing 2 - Actuator 3 - Side Linkage 4 - Blade 5 - Tip Seal 6 - Side Seal (Jamb Seal) 7 - Bearing 8 - Landing Angles
Axle and Drive Shaft Fixing Details Mounting Bracket for Actuator
Flange Type Flange Type
200 200 2
300 200 2
300 300 3
VOLUME CONTROL DAMPERS
36 Right to alterations reserved. SAFID is a registered trademark. © Copyright 2018. All rights reserved Right to alterations reserved. SAFID is a registered trademark. © Copyright 2018. All rights reserved 37
INSTALLATION DETAILS ORDER REFERENCE DETAILS
SPK 30 SERIES [SPK 30 - 300L, SPK 30 - 310L] SPK 30 SERIES [SPK 30 - 300L, SPK 30 - 310L]
Damper to Slide on Flange Connection Damper to Angle Flange Connection Order Code SPK 30 - 300L - OB - B - R - 900 x 900 - A
Order Example
200 200 2 2
300 200 3 2 Standard
300 300 3 3 Make: SAFID
4 1. Type : SPK 30 - 300L - OB - B - R - 900 x 900 - A
VOLUME CONTROL DAMPERS
500 400 4 4
600 400 5 4
500 500 4 4
600 500 5 4
700 500 6 4
600 600 5 5
700 600 6 5
800 600 7 5
700 700 6 6
800 700 7 6
900 700 8 6
800 800 7 7
900 800 8 7
900 900 8 8
Catalog ID: SPK 30 - 300L December 18, 2013 Catalog ID: SPK 30 - 300L December 18, 2013
38 Right to alterations reserved. SAFID is a registered trademark. © Copyright 2018. All rights reserved Right to alterations reserved. SAFID is a registered trademark. © Copyright 2018. All rights reserved 39
FLANGE TYPE VCD WITH EXTRUDED FLANGE TYPE VCD WITH EXTRUDED
ALUMINUM AIRFOIL BLADES ALUMINUM AIRFOIL BLADES
Blades: Catalog ID: SPK 30 - 400 January 23, 2014 Data are based on a torque of 24.6 in.-lb/ft2 applied to close and seat the damper during the test.
100mm, 125mm and 150mm wide airfoil shaped blades
extruded aluminum.
SAFID certifies that the Class 1A & Class 1 Low Leakage Volume SAFID certifies that the Class 1A & Class 1 Low Leakage Volume
Control Damper shown herein is licensed to bear the AMCA Control Damper shown herein is licensed to bear the AMCA
Finish: Seal for Model SPK 30-400. The ratings shown are based on Seal for Model SPK 30-400. The ratings shown are based on
Frame of mill galvanized. tests and procedures performed in accordance with AMCA tests and procedures performed in accordance with AMCA
Publication 511 and comply with the requirements of the AMCA Publication 511 and comply with the requirements of the AMCA
Blades of mill aluminum. Certified Ratings Program.The AMCA Certified Ratings Seal Certified Ratings Program.The AMCA Certified Ratings Seal
applies to Air Leakage and Air Performance Ratings. applies to Air Leakage and Air Performance Ratings.
Test Information: Tested for air leakage in accordance with ANSI Test Information: Tested for air leakage in accordance with ANSI
External Linkage: / AMCA Standard 500-D-07,Figure 5.4. Air leakage is based on / AMCA Standard 500-D-07,Figure 5.4. Air leakage is based on
operation between 32 ºF and 120 ºF. Tested for air performance operation between 32 ºF and 120 ºF. Tested for air performance
Galvanized steel side linkage concealed in frame for
in accordance with ANSI / AMCA Standard 500-D-07 (Pressure in accordance with ANSI / AMCA Standard 500-D-07 (Pressure
opposed blade operation. Drop), Figure 5.3. Only 150mm blade width is AMCA certified. Drop), Figure 5.3. Only 150mm blade width is AMCA certified. Catalog ID: SPK 30 - 400 January 23, 2014
40 Right to alterations reserved. SAFID is a registered trademark. © Copyright 2018. All rights reserved Right to alterations reserved. SAFID is a registered trademark. © Copyright 2018. All rights reserved 41
FLANGE TYPE VCD WITH EXTRUDED FLANGE TYPE VCD WITH EXTRUDED
ALUMINUM AIRFOIL BLADES ALUMINUM AIRFOIL BLADES
SPK 30 SERIES [SPK 30 - 400, SPK 30 - 410] SPK 30 SERIES [SPK 30 - 400, SPK 30 - 410]
Pressure Drop at Face Area Velocity Pressure Drop at Face Area Velocity
Damper Size 12 in. x 12 in. - Fully Open Blades Damper Size 24 in. x 24 in. - Fully Open Blades
VOLUME CONTROL DAMPERS
42 Right to alterations reserved. SAFID is a registered trademark. © Copyright 2018. All rights reserved Right to alterations reserved. SAFID is a registered trademark. © Copyright 2018. All rights reserved 43
FLANGE TYPE VCD WITH EXTRUDED FLANGE TYPE VCD WITH EXTRUDED
ALUMINUM AIRFOIL BLADES ALUMINUM AIRFOIL BLADES
SPK 30 SERIES [SPK 30 - 400, SPK 30 - 410] SPK 30 SERIES [SPK 30 - 400, SPK 30 - 410]
Pressure Drop 1 - Casing 2 - Actuator 3 - Side Linkage 4 - Blade 5 - Tip Seal 6 - Side Seal (Jamb Seal) 7 - Bearing 8 - Landing Angles
150 100 1 - -
VOLUME CONTROL DAMPERS
SAFID certifies that the Class 1A & Class 1 Low Leakage Volume 650 650 2 - 3
Control Damper shown herein is licensed to bear the AMCA
Seal for Model SPK 30-400. The ratings shown are based on 700 700 1 - 4
tests and procedures performed in accordance with AMCA
Publication 511 and comply with the requirements of the AMCA 750 750 - - 5
Certified Ratings Program.The AMCA Certified Ratings Seal
applies to Air Leakage and Air Performance Ratings. 800 800 2 - 4
Test Information: Tested for air leakage in accordance with ANSI
/ AMCA Standard 500-D-07,Figure 5.4. Air leakage is based on 850 850 1 - 5
operation between 32 ºF and 120 ºF. Tested for air performance
in accordance with ANSI / AMCA Standard 500-D-07 (Pressure 900 900 - - 6
Drop), Figure 5.3. Only 150mm blade width is AMCA certified. Catalog ID: SPK 30 - 400 January 23, 2014 Catalog ID: SPK 30 - 400 January 23, 2014
44 Right to alterations reserved. SAFID is a registered trademark. © Copyright 2018. All rights reserved Right to alterations reserved. SAFID is a registered trademark. © Copyright 2018. All rights reserved 45
MATERIALS CONSTRUCTION INSTALLATION DETAILS
SPK 30 SERIES [SPK 30 - 400, SPK 30 - 410] SPK 30 SERIES [SPK 30 - 400, SPK 30 - 410]
150 150 2 2
200 150 2 2
300 300 3 3
4
VOLUME CONTROL DAMPERS
500 300 4 3
450 450 4 4
500 450 4 4
600 450 5 4
700 450 6 4
800 450 7 4
900 450 8 4
600 600 5 5
700 600 6 5
800 600 7 5
900 600 8 5
750 750 6 5
800 750 7 5
900 750 8 5
900 900 8 8
Catalog ID: SPK 30 - 400 January 23, 2014 Catalog ID: SPK 30 - 400 January 23, 2014
46 Right to alterations reserved. SAFID is a registered trademark. © Copyright 2018. All rights reserved Right to alterations reserved. SAFID is a registered trademark. © Copyright 2018. All rights reserved 47
ORDER REFERENCE DETAILS SLEEVE TYPE VOLUME CONTROL DAMPER
Blade edge seals and jamb (side) seals can be fitted for Temperature Limits:
low leakage requirements. Dampers can be manual with -40 ˚C to + 100 ˚C.
locking quadrant or motorized with a wide range of
electrical actuators readily available.
Order Example SPK 40 - 110
General construction as type SPK 40 - 100 damper but
Standard Construction blades, shafts and blade to shaft fixing in stainless steel
Standard (Grade 304).
Make: SAFID Frame:
VOLUME CONTROL DAMPERS
Finish:
Mill Galvanized
Linkage:
Face linkage parallel blade operation.
Case Bearing:
Brass bearing as standard.
Sintered bronze oilite (optional).
Axles:
12mm diameter zinc plated mild steel.
48 Right to alterations reserved. SAFID is a registered trademark. © Copyright 2018. All rights reserved Right to alterations reserved. SAFID is a registered trademark. © Copyright 2018. All rights reserved 49
CIRCULAR SPIGOT TYPE VOLUME
SLEEVE TYPE VOLUME CONTROL DAMPER
CONTROL DAMPER
Dimensions
1 - Casing 2 - Drive Shaft/ Removable Spindle (when required) 3 - Bar Linkage 4 - Blade 5 - Landing Angles
6 - BearingAngles
Sleeve Type, Parallel Blades Standard Sizes Blade action is standard as parallel but can be supplied as For details of multiple sections consult SAFID.
opposed blade action at no addtional charge.
Width (mm) Height (mm) No. of Blades Temperature Limits:
Blade edge seals and jamb (side) seals can be fitted for -40 ˚C to + 100 ˚C.
100 100 1 low leakage requirements. Dampers can be manual with
150 150 1 locking quadrant or motorized with a wide range of
200 200 electrical actuators readily available. SPK 50 - 110
1
General construction as type SPK 50 - 100 damper but
250 250 1
Standard Construction blades, shafts and blade to shaft fixing in stainless steel
300 300 1 (Grade 304).
350 350 2 Frame:
SPK 50 - 120
VOLUME CONTROL DAMPERS
50 Right to alterations reserved. SAFID is a registered trademark. © Copyright 2018. All rights reserved Right to alterations reserved. SAFID is a registered trademark. © Copyright 2018. All rights reserved 51
CIRCULAR SPIGOT TYPE VOLUME OVAL SPIGOT TYPE VOLUME
CONTROL DAMPER CONTROL DAMPER I SPK SERIES
Dimensions
1 - Casing 2 - Drive Shaft/ Removable Spindle (when required) 3 - Bar Linkage 4 - Blade 5 - Landing Angles
6 - BearingAngles
Blade action is standard as parallel but can be supplied as For details of multiple sections consult SAFID.
opposed blade action at no addtional charge.
Temperature Limits:
Blade edge seals and jamb (side) seals can be fitted for -40 ˚C to + 100 ˚C.
Circular Spigot Type, Parallel/Opposed Blades Standard Sizes low leakage requirements. Dampers can be manual with
locking quadrant or motorized with a wide range of
Diameter (mm) No. of Blades electrical actuators readily available. SPK 60 - 110
General construction as type SPK 60 - 100 damper but
100 1 blades, shafts and blade to shaft fixing in stainless steel
150 1 Standard Construction (Grade 304).
200 1
Frame: SPK 60 - 120
VOLUME CONTROL DAMPERS
700 4
Linkage:
Parallel Blades (PB) Opposed Blades (OB) 800 5 Side linkage concealed in frame for parallel and opposed
900 6 blade operation.
1000 7
Face linkage available (optional).
1100 7
Case Bearing:
1150 7 Brass bearing as standard.
Sintered bronze oilite (optional).
Axles:
12mm diameter zinc plated mild steel.
52 Right to alterations reserved. SAFID is a registered trademark. © Copyright 2018. All rights reserved Right to alterations reserved. SAFID is a registered trademark. © Copyright 2018. All rights reserved 53
OVAL SPIGOT TYPE VOLUME
MATERIALS CONSTRUCTION
CONTROL DAMPER
SPK SERIES [SPK 60 - 100, SPK 60 - 110, SPK 60 - 120] SPK SERIES [SPK 60 - 100, SPK 60 - 110, SPK 60 - 120]
Dimensions
Oval Spigot Type Oval Spigot Type For Sleeve Type Only Damper with Mounting Bracket for Actuator
Oval pigot Type, Parallel/Opposed Blades Standard Sizes - Single Section Blade Seal Side Seal (Jamb Seal)
H-3 x W-3
550 450 3
600 500 4
650 600 4
700 700 4
750 800 5
Parallel Blades (PB) Opposed Blades (OB)
800 900 6
850
900
950
1000
Note:
Type S3 (Combination of S1 & S2)
54 Right to alterations reserved. SAFID is a registered trademark. © Copyright 2018. All rights reserved Right to alterations reserved. SAFID is a registered trademark. © Copyright 2018. All rights reserved 55
INSTALLATION DETAILS INSTALLATION DETAILS
Flange Type SPK 30 Flange Type SPK 30 Sleeve Type SPK 40 Circular Type SPK 50 and Oval type SPK 60
100 100 1 2
150 150 2 2
200 200 2 2
250 250 2 3
300 300 3 3
350 350 3 4
VOLUME CONTROL DAMPERS
56 Right to alterations reserved. SAFID is a registered trademark. © Copyright 2018. All rights reserved Right to alterations reserved. SAFID is a registered trademark. © Copyright 2018. All rights reserved 57
PRODUCT RANGE ORDER REFERENCE DETAILS
58 Right to alterations reserved. SAFID is a registered trademark. © Copyright 2018. All rights reserved Right to alterations reserved. SAFID is a registered trademark. © Copyright 2018. All rights reserved 59
FLANGE TYPE VOLUME CONTROL FLANGE TYPE VOLUME CONTROL
DAMPER WITH AIRFOIL BLADES DAMPER WITH AIRFOIL BLADES
Dimensions
950
Axles and Control Shaft:
12mm diameter zinc plated mild steel. 1000
1050
60 Right to alterations reserved. SAFID is a registered trademark. © Copyright 2018. All rights reserved Right to alterations reserved. SAFID is a registered trademark. © Copyright 2018. All rights reserved 61
SLEEVE TYPE VOLUME CONTROL SLEEVE TYPE VOLUME CONTROL
DAMPER WITH AIRFOIL BLADES DAMPER WITH AIRFOIL BLADES
Dimensions
950
Axles and Control Shaft:
1000
12mm diameter zinc plated mild steel.
1050
62 Right to alterations reserved. SAFID is a registered trademark. © Copyright 2018. All rights reserved Right to alterations reserved. SAFID is a registered trademark. © Copyright 2018. All rights reserved 63
CIRCULAR SPIGOT TYPE VOLUME CONTROL CIRCULAR SPIGOT TYPE VOLUME CONTROL
DAMPER WITH AIRFOIL BLADES DAMPER WITH AIRFOIL BLADES
Dimensions
Blade seals and jamb (side) seals can be fitted for low SPK 50 - 210
leakage requirements. Dampers can be manual with General construction as type SPK 50 - 200 damper but
locking quadrant or motorized with a wide range of blades, shafts and blade to shaft fixing in stainless steel
electrical actuators readily available. (Grade 304).
64 Right to alterations reserved. SAFID is a registered trademark. © Copyright 2018. All rights reserved Right to alterations reserved. SAFID is a registered trademark. © Copyright 2018. All rights reserved 65
OVAL SPIGOT TYPE VOLUME CONTROL OVAL SPIGOT TYPE VOLUME CONTROL
DAMPER WITH AIRFOIL BLADES DAMPER WITH AIRFOIL BLADES
Dimensions
Blade seals and jamb (side) seals can be fitted for low SPK 60 - 210
leakage requirements. Dampers can be manual with General construction as type SPK 60 - 200 damper but
locking quadrant or motorized with a wide range of blades, shafts and blade to shaft fixing in stainless steel
electrical actuators readily available. (Grade 304).
Standard Construction SPK 60 - 220 Oval Spigot Type, Parallel/Opposed Blades Standard Sizes
General construction as type SPK 60 - 200 damper but
Frame (Spigot Type): with frame, blades shafts and blade to shaft fixing and Width (mm) Height (mm) No. of Blades
180mm x 1.5mm (16 ga.) galvanized steel, spigot type linkage all from stainless steel (Grade 304).
200 150 1
380mm wide with ova spigot duct connection.
250 200 1
Blades:
VOLUME CONTROL DAMPERS
700
Case Bearing:
Parallel Blades (PB) Opposed Blades (OB) 750
Brass bearing as standard.
Sintered bronze oilite (optional). 800
850
Axles and Control Shaft:
900
12mm diameter zinc plated mild steel.
950
1000
66 Right to alterations reserved. SAFID is a registered trademark. © Copyright 2018. All rights reserved Right to alterations reserved. SAFID is a registered trademark. © Copyright 2018. All rights reserved 67
MATERIALS CONSTRUCTION INSTALLATION DETAILS
Removable Spindle Mounting Bracket Flange Type SPK 30 Flange Type SPK 30
68 Right to alterations reserved. SAFID is a registered trademark. © Copyright 2018. All rights reserved Right to alterations reserved. SAFID is a registered trademark. © Copyright 2018. All rights reserved 69
INSTALLATION DETAILS PRODUCT RANGE
Sleeve type SPK 40 Circular type SPK50 & Oval type SPK60
Seals Belimo Actuators
PB Side linkage concealed in frame A15 NF120-S US Spring Return With Limit Switch
Pressure Loss for parallel blade operation.
Face linkage available (optional) A16 NF24-SR US Modulating
70 Right to alterations reserved. SAFID is a registered trademark. © Copyright 2018. All rights reserved Right to alterations reserved. SAFID is a registered trademark. © Copyright 2018. All rights reserved 71
REFERENCE DETAILS ORDER REFERENCE DETAILS
Specifications
Order Code SPK 30 - 200 - PB - S - B - R / 500 x 500 / A17
Airfoil blades volume control dampers designed for
volume flow and pressure control or to isolate sections
Frame Type of ducting in ventilation systems, shall be of the SPK
*SPK30 = Flange (Standard Supply) Actuator 200 series as specified.
SPK40 = Sleeve (See Page 71)
SPK50 = Circular Spigot Damper casing will be constructed of Ga. 16 galva-
SPK60 = Oval Spigot Duct Size nized steel. Blades shall be double skin (airfoil section
Square or Rectangular blades of Ga. 22 galvanized steel (optional) with blade
Type Dimensions ‘W’ x ‘H’ seals and/or side seals).
*200 (Standard Supply) mm Circular ‘D’ mm
210 dia. Flat oval ‘W’ x ‘H’ Shafts to be 12mm mild plated steel with brass or
220 mm.All damper spigots sintered bronze bearings. Blades to be connected by
are manufactured face or external linkage.
Variants - Blade Operation down on duct size to
*PB = Slide Linkage Parallel fit insideductwork Parallel or opposed blade operation dampers; with
(Standard Supply) connections. manual or motorized operation. Limit switches and
OB = Opposed Blade closed blade low leakage constructions are optional
External Controls readily available.
Variants - Seals *R = Right Hand
*S = None (Standard Supply) (Standard Supply)
S1 = Blade Seals Only (175 ˚C) L = Left Hand
Order Example
S2 = Side Seal (Jamb)
S3 = Side Seal & Blade Seals (175 ˚C)
Standard
Make: SAFID
Variants - Bearings
Type : SPK 30 - 200 - PB - S - B - R / 500 x 500
*B = Brass (Standard Supply)
Qty: 1
B1 = Sintered Bronze oilite (optional)
B2 = Stainless Steel
SP 500 SP SERIES
SP SERIES [SP 500, SP 510, SP 520]
Dimensions
Description SP 510
General construction as type SP 500 damper but blades,
Casing and blades made from galvanized steel sheet. shafts and blade to shaft fixing in stainless steel (Grade
304).
Adjustable damper blade mounted on brass bushes with
manually operated quadrant and position indicator. The SP 520
damper is used for regulating air flow or as shutt-off General construction as type SP 500 damper but with
damper when complete sealing against air flow is not frame, blades shafts and blade to shaft fixing all from
required. stainless steel (Grade 304).
Standard Construction
Section Details Standard Sizes
Body:
Galvanized steel sheet.
Gauge 20 : from Dia. 80mm to 500mm. Dia (mm) Dia (mm)
Gauge 18 : above 500 Dia.
80 305
100 315
VOLUME CONTROL DAMPERS
Control Shaft:
12mm diameter zinc plated mild steel.
The end joints are also available with factory applied
Minimum and Maximum Size: self sealing gaskets.
80mm Dia. damper up to 610 Dia. are single blade
construction.
74 Right to alterations reserved. SAFID is a registered trademark. © Copyright 2018. All rights reserved Right to alterations reserved. SAFID is a registered trademark. © Copyright 2018. All rights reserved 75
ROUND SHUT OFF VOLUME CONTROL DAMPER ROUND SHUT OFF VOLUME CONTROL DAMPER
SP 600 SP SERIES
SP SERIES [SP 600, SP 610, SP 620]
Dimensions
Description SP 610
General construction as type SP 600 damper but blades,
Casing and blades made from galvanized steel sheet. shafts and blade to shaft fixing in stainless steel (Grade
304).
Adjustable damper blade mounted on brass bushes and
blades with rubber seal, when complete sealing of air flow SP 620
is required. General construction as type SP 600 damper but with
frame, blades shafts and blade to shaft fixing all from
Dampers can be manual with locking quadrant and stainless steel (Grade 304).
position indicator or motorized with a wide range of
electrical actuators readily available.
Standard Construction
Body:
Section Details Standard Sizes
Galvanized steel sheet.
Gauge 20 : from Dia. 80mm to 500mm.
Gauge 18 : above 500 Dia.
Dia (mm) Dia (mm)
Blade:
Gauge 14 (2mm thk) : 2 layers gauge 20 plain galvanized 80 305
VOLUME CONTROL DAMPERS
76 Right to alterations reserved. SAFID is a registered trademark. © Copyright 2018. All rights reserved Right to alterations reserved. SAFID is a registered trademark. © Copyright 2018. All rights reserved 77
ROUND SHUTT OFF DAMPER ROUND SHUTT OFF DAMPER
SP 700 SP SERIES
SP SERIES [SP 700, SP 710, SP 720]
Dimensions
Description SP 710
General construction as type SP 700 damper but blades,
Casing and blades made from heavy galvanized steel shafts and blade to shaft fixing in stainless steel (Grade
sheet. 304).
Option:
Damper with Airtight Blade:
Stopper end for airtight blade, code AT.
Standard Construction
Dia (mm) Dia (mm)
Body: 80 305
VOLUME CONTROL DAMPERS
78 Right to alterations reserved. SAFID is a registered trademark. © Copyright 2018. All rights reserved Right to alterations reserved. SAFID is a registered trademark. © Copyright 2018. All rights reserved 79
PRODUCT DETAILS
Installation Details
Order Example
VOLUME CONTROL DAMPERS
Type
SP 500
SP 600
SP 700
Diameter
80 Right to alterations reserved. SAFID is a registered trademark. © Copyright 2018. All rights reserved Right to alterations reserved. SAFID is a registered trademark. © Copyright 2018. All rights reserved 81
PRESSURE
RELIEF
DAMPERS
PRESSURE RELIEF DAMPERS
Air Performance
Pressure Drop
Standard Construction
PRD 50 - 110
Frame: General construction as type PRD 50 - 100 damper but
Gauge 18 (1.2mm thick) formed galvanized steel sheet. frame and blades are all from mill finish aluminum sheets.
Shaft:
Blade stub shafts in brass.
SAFID certifies that the Pressure Relief Damper shown herein is SAFID certifies that the Pressure Relief Damper shown herein is
licensed to bear the AMCA Seal for Model PRD 50-100 & PRD licensed to bear the AMCA Seal for Model PRD 50-100 & PRD
50A-100. The ratings shown are based on tests and procedures 50A-100. The ratings shown are based on tests and procedures
performed in accordance with AMCA Publication 511 and performed in accordance with AMCA Publication 511 and
comply with the requirements of the AMCA Certified Ratings comply with the requirements of the AMCA Certified Ratings
Program. Program.
The AMCA Certified Ratings Seal applies to Air Performance The AMCA Certified Ratings Seal applies to Air Performance
Ratings. Ratings.
Test Information Test Information
Tested for air performance in accordance with ANSI / AMCA Tested for air performance in accordance with ANSI / AMCA
Standard 500-L-12 (Pressure Drop), Figure 5.4. Catalog ID: PRD 50 - 100 & PRD 50A - 100, March 11, 2014 Standard 500-L-12 (Pressure Drop), Figure 5.4. Catalog ID: PRD 50 - 100 & PRD 50A - 100, March 11, 2014
84 Right to alterations reserved. SAFID is a registered trademark. © Copyright 2018. All rights reserved Right to alterations reserved. SAFID is a registered trademark. © Copyright 2018. All rights reserved 85
WALL MOUNTED PRESSURE RELIEF DAMPER WALL MOUNTED PRESSURE RELIEF DAMPER
PRD 50A SERIES [PRD 50A - 100, PRD 50A - 110, PRD 50A - 120, PRD 50A - 130] PRD 50 SERIES [PRD 50 - 100, PRD 50 - 110, PRD 50 - 120, PRD 50 - 130]
PRD 50 - 100, 110, 120, 130 PRD 50A - 100, 110, 120, 130
PRESSURE RELIEF DAMPERS
86 Right to alterations reserved. SAFID is a registered trademark. © Copyright 2018. All rights reserved Right to alterations reserved. SAFID is a registered trademark. © Copyright 2018. All rights reserved 87
PRODUCT DETAILS WALL MOUNTED PRESSURE RELIEF DAMPER
Order Example:
PRD 50 - 100
PRD 50 - 110
PRD 50 - 120
PRD 50 - 130
PRD 50A - 100
PRD 50A - 110
PRD 50A - 120
PRD 50A - 130
Sizes
Standard
Make : SAFID Description Minimum Size:
Type : PRD 50 - 100 - 500 x 500 150mm x 100mm (6in x 4in).
Type : PRD 50A - 100 - 500 x 500 Pressure relief dampers are used in intake and discharge
openings in commercial and residential ventilation Maximum Size:
systems. When the ventilation system is on, the blades of 1000mm x 1000mm (W x H) as single section without
the pressure relief damper are held in the open position mullion.
Standard Sizes Specifications by the airflow. If the system is switched off, the damper 2000mm x 2000mm (W x H) as single section with
blades close automatically, thus preventing reverse airflow horizontal and vertical mullions.
Width (mm) Height (mm) and giving protection against the ingress of untempered
air, rain and birds into the ventilation system. Consult SAFID for multiple section assembly details.
100 100 Pressure relief dampers are used for intake and
100
discharge openings in ventilation systems to
200
prevent reverse airflow and for protection against Standard Construction
150 300
ingress of rain into ventilation systems.Basically PRD 40 - 110
200 400 Frame: General construction as type PRD 40 - 100 damper but
the frame is built of galvanised steel (standard)
250 500 or aluminum and corrugated aluminum blades Gauge 18 (1.2mm thick) formed galvanized steel sheet. frame is from mill finish aluminum sheets.
300 600 (standard) with blade seals opening and closing
Blades: PRD 40 - 120
350 700 automatically.
100mm maximum width, 1.5mm thick extruded aluminum General construction as type PRD 40 - 100 damper but
400 800 profile. Sealing strip on blades in foam gasket. with counter weight.
450 900
Linkage: PRD 40 - 130
500 1000
Galvanized steel sheet 15mm x 20 Gauge. General construction as type PRD 40 - 100 damper but
PRESSURE RELIEF DAMPERS
900 1500
Shaft:
1000 1600 Blade stub shafts in plastic, 6mm x 6mm square.
1200 1700
SAFID certifies that the Pressure Relief Damper shown herein SAFID certifies that the Pressure Relief Damper shown herein
is licensed to bear the AMCA Seal for Model PRD 50 - 100 is licensed to bear the AMCA Seal for Model PRD 40 - 100
& PRD 50A - 100. The ratings shown are based on tests and & PRD 40A - 100. The ratings shown are based on tests and
procedures performed in accordance with AMCA Publication procedures performed in accordance with AMCA Publication
511 and comply with the requirements of the AMCA Certified 511 and comply with the requirements of the AMCA Certified
Ratings Program. Ratings Program.
The AMCA Certified Ratings Seal applies to Air Performance The AMCA Certified Ratings Seal applies to Air Performance
Ratings. Ratings.
Test Information Test Information
Tested for air performance in accordance with ANSI / AMCA Tested for air performance in accordance with ANSI / AMCA
Standard 500-L-12 (Pressure Drop), Figure 5.4. Catalog ID: PRD 50 - 100 & PRD 50A - 100, March 11, 2014 Standard 500-L-12 (Pressure Drop), Figure 5.4. Catalog ID: PRD 40 - 100 & PRD 40A - 100, March 11, 2014
88 Right to alterations reserved. SAFID is a registered trademark. © Copyright 2018. All rights reserved Right to alterations reserved. SAFID is a registered trademark. © Copyright 2018. All rights reserved 89
WALL MOUNTED PRESSURE RELIEF DAMPER WALL MOUNTED PRESSURE RELIEF DAMPER
PRD 40 SERIES [PRD 40 - 100, PRD 40 - 110, PRD 40 - 120, PRD 40 - 130] PRD 40A SERIES [PRD 40A - 100, PRD 40A - 110, PRD 40A - 120, PRD 40A - 130]
90 Right to alterations reserved. SAFID is a registered trademark. © Copyright 2018. All rights reserved Right to alterations reserved. SAFID is a registered trademark. © Copyright 2018. All rights reserved 91
WALL MOUNTED PRESSURE RELIEF DAMPER PRODUCT DETAILS
PRD 40 SERIES [PRD 40 - 100, PRD 40 - 110, PRD 40 - 120, PRD 40 - 130)
Installation Details Order Reference Details
PRD 40 - 100
PRD 40 - 110
PRD 40 PRD 40 - 100, 110, 120, 130 PRD 40 - 120
PRD 40 - 130
PRD 40A - 100
PRD 40A - 110
PRD 40A - 120
PRD 40A - 130
Sizes
Standard
Make : SAFID
Type : PRD 40 - 100 - 500 x 500
Type : PRD 40A - 100 - 500 x 500
100 100 Pressure relief dampers are used for intake and
100 200 discharge openings in ventilation systems to prevent
150 300 reverse airflow and for protection against ingress of rain
PRD 40 - 100, 110, 120, 130 PRD 40A - 100, 110, 120, 130 into ventilation systems.Basically the frame is built of
200 400
galvanised steel (standard) or aluminum and extruded
250 500
aluminum blades with blade seals opening and closing
300 600
automatically.
350 700
400 800
PRESSURE RELIEF DAMPERS
500 1000
600 1200
700 1300
800 1400
900 1500
1000 1600
1200 1700
Catalog ID: PRD 40 - 100 & PRD 40A - 100, March 11, 2014 Catalog ID: PRD 40 - 100 & PRD 40A - 100, March 11, 2014
92 Right to alterations reserved. SAFID is a registered trademark. © Copyright 2018. All rights reserved Right to alterations reserved. SAFID is a registered trademark. © Copyright 2018. All rights reserved 93
DUCT MOUNTED PRESSURE RELIEF DAMPER DUCT MOUNTED PRESSURE RELIEF DAMPER
Frame:
Gauge 18 ga. (1.2mm thk.) from formed channel frame
PRD 30 - 100 PRD 30 - 100
galvanized steel sheet.
Blades:
100mm max. width, 0.75mm thk. mill finish aluminum
sheet. Sealing strip on blades in foam gasket.
Linkage:
PRESSURE RELIEF DAMPERS
Bearing:
Bearing section in plastic 6mm.
Shaft:
Blade stub shafts in brass.
Minimum Size:
100 x 100mm, damper up to 200mm high are single blade
construction.
Maximum Size:
1000 x 1500mm, as single section.
Multiple section assembly with unlimited size, where each
section operates independently.
94 Right to alterations reserved. SAFID is a registered trademark. © Copyright 2018. All rights reserved Right to alterations reserved. SAFID is a registered trademark. © Copyright 2018. All rights reserved 95
INSTALLATION DETAILS PRODUCT DETAILS
PRD 30 SERIES [PRD 30 - 100, PRD 30 - 110, PRD 30 - 120, PRD 30 - 130] PRD 30 SERIES [PRD 30 - 100, PRD 30 - 110, PRD 30 - 120, PRD 30 - 130]
PRD 30
PRD 30 - 100
PRD 30 - 110
PRD 30 - 120
PRD 30 - 130
Sizes
Standard
Make : SAFID
Type : PRD 30 - 100 - 500 x 500
Qty : 1
Insert Type
100 100 Pressure relief dampers are used for intake and
100 200 discharge openings in air conditioning systems to
prevent reverse air flow and for protection against
PRESSURE RELIEF DAMPERS
150 300
Catalog ID: PRD 30 - 100 & PRD 30A - 100, March 11, 2014
96 Right to alterations reserved. SAFID is a registered trademark. © Copyright 2018. All rights reserved Right to alterations reserved. SAFID is a registered trademark. © Copyright 2018. All rights reserved 97
SPIN IN
DAMPERS
SPIN IN DAMPERS
SPIN IN DAMPERS
98 Right to alterations reserved. SAFID is a registered trademark. © Copyright 2018. All rights reserved Right to alterations reserved. SAFID is a registered trademark. © Copyright 2018. All rights reserved 99
SPIN IN DAMPER SPIN IN DAMPER
SFLD 10 SFLDE 10
Spin In Collar with Damper Blade Spin In collar with Damper Blade and Extractor SFLD SERIES [SFLD 10, SFLDE 11, SFLD 12, SFLDE 12]
SFLD SFLDE
Spin Collar with Damper Blade Spin In Collar with Damper Blade and Extractor
Frame:
Galvanized steel sheet (24 gauge).
Blades:
Plain galvanized steel sheet (20 gauge).
Galvanized steel perforated blade (optional).
Finish:
Mill galvanized.
SPIN IN DAMPERS
SPIN IN DAMPERS
Case Bearing:
Plastic bushing
Control Shaft:
6mm diameter zinc plated mild steel
100 Right to alterations reserved. SAFID is a registered trademark. © Copyright 2018. All rights reserved Right to alterations reserved. SAFID is a registered trademark. © Copyright 2018. All rights reserved 101
PRODUCT DETAILS
SFLD SERIES [SFLD 10, SFLDE 11, SFLD 12, SFLDE 12]
Installation Details
80 120
100 120 Order Example
125 120
Product Code: SFLD 10 - aaa
140 120
150 120
160 120 Type
180 120
SFLD 10
SFLDE 10
200 120
SPIN IN DAMPERS
SPIN IN DAMPERS
224 120
Diameter
250 120
280 120
305 120
315 120
102 Right to alterations reserved. SAFID is a registered trademark. © Copyright 2018. All rights reserved Right to alterations reserved. SAFID is a registered trademark. © Copyright 2018. All rights reserved 103
CURTAIN
TYPE FIRE
DAMPERS
CURTAIN T YPE FIRE DAMPERS
The SSA range of curtain bladed fire dampers are suitable For details of multiple sections consult SAFID.
for installation in walls and ceilings made from concrete or
brickwork, and will stop the spread of fire through duct,
walls or floors. SSA-1-A-110
General construction as type SSA-1-A-100 damper but
There is a wide choice of sizes available for low, medium blades in stainless steel (Grade 304).
and high velocity applications and inlcude rectangular,
W x H = Duct Size
square, circular and flat oval connections. SSA-1-A-120
General construction as type SSA-1-A-100 damper but
The dampers are fitted with standard release 74 °C frame, blades and catchplates all from stainless steel
fusible links (UL listed) unless otherwise specified. (Grade 304). Vertical Mounting Horizontal Mounting
Blades:
Built of 20 gauge (0.93mm) galvanized steel.
Finish:
Mill galvanized.
Fusible Link:
Standard release 74 °C. (165 °F) UL listed.
Other temperatures available on request.
Springs:
Stainless steel closure springs.
Fire Rating:
Up to 4 hours fire rating.
Minimum Size:
100 x 100mm
106 Right to alterations reserved. SAFID is a registered trademark. © Copyright 2018. All rights reserved Right to alterations reserved. SAFID is a registered trademark. © Copyright 2018. All rights reserved 107
CURTAIN TYPE FIRE DAMPER CURTAIN TYPE FIRE DAMPER
WITH BLADES OUTSIDE AIR STREAM WITH BLADES OUTSIDE AIR STREAM
The SSA range of curtain bladed fire dampers are suitable For details of multiple sections consult SAFID.
for installation in walls and ceilings made from concrete or
brickwork, and will stop the spread of fire through duct,
walls or floors. SSA-1-B-110
General construction as type SSA-1-B-100 damper but
There is a wide choice of sizes available for low, medium blades in stainless steel (Grade 304).
and high velocity applications and inlcude rectangular,
W x H = Duct Size
square, circular and flat oval connections.
SSA-1-B-120
The dampers are fitted with standard release 74 °C General construction as type SSA-1-B-100 damper but
fusible links (UL listed) unless otherwise specified. frame, blades and catchplates all from stainless steel
Horizontal Mounting Overall Damper Height
(Grade 304). Duct Height ‘H’ Y
(H + Y - 6)
108 Right to alterations reserved. SAFID is a registered trademark. © Copyright 2018. All rights reserved Right to alterations reserved. SAFID is a registered trademark. © Copyright 2018. All rights reserved 109
CURTAIN TYPE FIRE DAMPER CURTAIN TYPE FIRE DAMPER
FRAME AND BLADES FRAME AND BLADES
The SSA range of curtain bladed fire dampers are suitable For details of multiple sections consult SAFID.
for installation in walls and ceilings made from concrete or
brickwork, and will stop the spread of fire through duct,
walls or floors. SSA-1-C-110
General construction as type SSA-1-C-100 damper but
There is a wide choice of sizes available for low, medium blades in stainless steel (Grade 304).
and high velocity applications and inlcude rectangular,
W x H = Duct Size
square, circular and flat oval connections.
SSA-1-C-120
The dampers are fitted with standard release 74 °C General construction as type SSA-1-C-100 damper but
fusible links (UL listed) unless otherwise specified. frame, blades and catchplates all from stainless steel
Horizontal Mounting Overall Damper Height
(Grade 304). Duct Height ‘H’ Y
(H + Y - 6)
110 Right to alterations reserved. SAFID is a registered trademark. © Copyright 2018. All rights reserved Right to alterations reserved. SAFID is a registered trademark. © Copyright 2018. All rights reserved 111
CURTAIN TYPE FIRE DAMPER CURTAIN TYPE FIRE DAMPER
WITH ROUND SPIGOT WITH ROUND SPIGOT
The SSA range of curtain bladed fire dampers are suitable For details of multiple sections consult SAFID.
for installation in walls and ceilings made from concrete or
brickwork, and will stop the spread of fire through duct,
walls or floors. SSA-1-R-110
General construction as type SSA-1-R-100 damper but
There is a wide choice of sizes available for low, medium blades in stainless steel (Grade 304).
and high velocity applications and inlcude rectangular,
square, circular and flat oval connections.
SSA-1-R-120
The dampers are fitted with standard release 74 °C General construction as type SSA-1-R-100 damper but
fusible links (UL listed) unless otherwise specified. frame, blades and catchplates all from stainless steel
(Grade 304).
Horizontal Mounting Overall Damper Height
Duct Height ‘H’ Y
(H + Y - 6)
SSA-1-R-100 Standard Construction
100 40 170
Frame: 150 50 230
CURTAIN T YPE FIRE DAMPERS
112 Right to alterations reserved. SAFID is a registered trademark. © Copyright 2018. All rights reserved Right to alterations reserved. SAFID is a registered trademark. © Copyright 2018. All rights reserved 113
CURTAIN TYPE FIRE DAMPER CURTAIN TYPE FIRE DAMPER
WITH OVAL SPIGOT WITH OVAL SPIGOT
The SSA range of curtain bladed fire dampers are suitable For details of multiple sections consult SAFID.
for installation in walls and ceilings made from concrete or
brickwork, and will stop the spread of fire through duct,
walls or floors. SSA-1-O-110
General construction as type SSA-1-O-100 damper but
There is a wide choice of sizes available for low, medium blades in stainless steel (Grade 304).
and high velocity applications and inlcude rectangular,
square, circular and flat oval connections.
SSA-1-O-120
The dampers are fitted with standard release 74 °C General construction as type SSA-1-O-100 damper but
fusible links (UL listed) unless otherwise specified. frame, blades and catchplates all from stainless steel
Horizontal Mounting Overall Damper Height
(Grade 304). Duct Height ‘H’ Y
H+Y-6
Minimum Size:
200 x 100 mm (W x H)
114 Right to alterations reserved. SAFID is a registered trademark. © Copyright 2018. All rights reserved Right to alterations reserved. SAFID is a registered trademark. © Copyright 2018. All rights reserved 115
PRODUCT RANGE ACCESSORIES
B1 As code B, C series but includes Vertical / Horizontal Interruption of electical current to activate closure of the curtain
side seals Mounting blade pack.
C1 S04
As an alternative to the solenoid for systems that require
R1 normally “ENERGISED” actuators that automatically operate
High in the event of an interruption of electrical supply. (Voltage
O1 24V, 110V & 240V). Standard fuse temperature 74˚C.
CURTAIN T YPE FIRE DAMPERS
116 Right to alterations reserved. SAFID is a registered trademark. © Copyright 2018. All rights reserved Right to alterations reserved. SAFID is a registered trademark. © Copyright 2018. All rights reserved 117
INSTALLATION DETAILS INSTALLATION DETAILS
SSA-1-A SSA-1-B
SSA-1-C Damper with Rectangular Spigot SSA-1-C Damper with Rectangular Spigot
Warres 49800, Fire Resistance up to 1 hr Warres 49800, Fire Resistance up to 2 hrs Fire Test BS 476 Part 20 1987
The fire dampers shown have been tested by an independent authority (Warrington Research Centre) according to British
Standards 476 Part 20; 1987 for a period of 4 hours.
The time / temperature curve required by this test procedure is shown below, after 4 hours test the SSA retained its integrity
with no significant openings being formed.
Warres 49800, Fire Resistance up to 3 hrs Warres 49800, Fire Resistance up to 4 hrs
CURTAIN T YPE FIRE DAMPERS
SSA-1 Series
Air Performance
Order Code SSA - 1 - B - 100 - V / 500 x 500 / S01
Type
SSA-1 Accessories
(See Page 117)
Construction Variants
A = Blades in Air Stream Duct Size
B = Blades out of Air Stream - Square or rectangular
C = Blades out of Air Stream Dimensions ‘W’ x ‘H’
R = Blades out of Air Stream mm.
(Circular Type) - Circular ‘D’ mm dia.
O = Blades out of Air Stream Flat oval ‘W’ x ‘H’ mm.
(Oval Type) - All damper spigots
are manufactured
Variants - Seals down ond duct size
A1 to fit inside ductwork
B1 connections.
C1
R1
O1
100
110
120
Mounting
V = Vertical Damper
H = Horizontal Damper
CURTAIN T YPE FIRE DAMPERS
Standard
Square or rectangular shutter type fire dampers for Make : SAFID
the isolation of fire zones in air conditioning systems. Type : SSA-1-A-100-500 x 500
Designed and fabricated to maintain integrity and Qty : 1
stability for 4 hours when tested to BS 476 Part 20;
1987. The SSA fire dampers consists of perimeter
frame case and interlocking shutter type blades. As
standard the case is complete with catchplates and
constant tension closure springs. Suitable for either
rectangular, circular or flat oval ducting and available
in high or low pressure/velocity construction.Standard
release 74˚C fusible link.
124 Right to alterations reserved. SAFID is a registered trademark. © Copyright 2018. All rights reserved Right to alterations reserved. SAFID is a registered trademark. © Copyright 2018. All rights reserved 125
BLADE
TYPE FIRE
DAMPERS
BLADE T YPE FIRE DAMPERS
MFD SERIES
Product Description
128 Right to alterations reserved. SAFID is a registered trademark. © Copyright 2018. All rights reserved Right to alterations reserved. SAFID is a registered trademark. © Copyright 2018. All rights reserved 129
BLADE TYPE FIRE DAMPER BLADE TYPE FIRE DAMPER
H-3
Frame:
130 x 24.5 x 1.5mm thick (Ga.16) galvanized steel hat UL Test Ratings
channel.
Fire Resistance: 1 1/2 Hour and 3 Hours
W-3
Blades:
1.5mm thick (Ga.16) galvanized steel “Triple Vee” (3V)
DIA + 25
groove type (standard).
W + 25 H + 25
DIA + 25
Blade Stop:
1.5mm thick (Ga.16) galvanized steel sheet bend at 45°
angle.
Linkage:
Side linkage concealed in frame (Standard).
130 Right to alterations reserved. SAFID is a registered trademark. © Copyright 2018. All rights reserved Right to alterations reserved. SAFID is a registered trademark. © Copyright 2018. All rights reserved 131
BLADE TYPE FIRE DAMPER
Types
132 Right to alterations reserved. SAFID is a registered trademark. © Copyright 2018. All rights reserved Right to alterations reserved. SAFID is a registered trademark. © Copyright 2018. All rights reserved 133
BLADE TYPE FIRE DAMPER BLADE TYPE FIRE DAMPER
MFD With Factory Installed Sleeve, ERL and Actuator MFD With Factory Installed Sleeve, ERL and Actuator
Model: MFD - 80 Model: MFD - 80
Height: Up to 220 mm Height: Up to 914 mm
Refer to technical data sheet of actuator or contact SAFID for the actuator specifications. Refer to technical data sheet of actuator or contact SAFID for the actuator specifications.
134 Right to alterations reserved. SAFID is a registered trademark. © Copyright 2018. All rights reserved Right to alterations reserved. SAFID is a registered trademark. © Copyright 2018. All rights reserved 135
BLADE TYPE FIRE DAMPER BLADE TYPE FIRE DAMPER
MFD With Factory Installed Sleeve, ERL and Actuator MFD With Factory Installed Sleeve, ERL and Actuator
Model: MFD - 80 Model: MFD - 80
Width: Up to 1118 mm Width: Up to 1828 mm
Height: Up to 610 mm Height: Up to 914 mm
Schedule of Actuator Types Note: Location of the actuator can be INSIDE or OUTSIDE the airstream.
Refer to technical data sheet of actuator or contact SAFID for the actuator specifications.
A. Multiple section damper with two position (open/close) spring retrun type actuators:
136 Right to alterations reserved. SAFID is a registered trademark. © Copyright 2018. All rights reserved Right to alterations reserved. SAFID is a registered trademark. © Copyright 2018. All rights reserved 137
BLADE TYPE FIRE DAMPER BLADE TYPE FIRE DAMPER
MFD With Factory Installed Sleeve, ERL and Actuator MFD With Factory Installed Sleeve, ERL and Actuator
Model: MFD - 80 Model: MFD - 80
Width: Up to 1118 mm Width: Up to 1828 mm
Height: Up to 1220 mm Height: Up to 1828 mm
Schedule of Actuator Types Note: Location of the actuator can be INSIDE or OUTSIDE the airstream.
Refer to technical data sheet of actuator or contact SAFID for the actuator specifications.
A. Multiple section damper with two position (open/close) spring retrun type actuators:
138 Right to alterations reserved. SAFID is a registered trademark. © Copyright 2018. All rights reserved Right to alterations reserved. SAFID is a registered trademark. © Copyright 2018. All rights reserved 139
INSTALLATION DETAILS ACTUATORS
Typical Installation
Sequence of Operation
The ERL (Thermoelectric Tripping Device) resettable link has a thermal sensor switch that interrups the power supply to the
fire damper actuator as soon as the duct temperature exceeds 165ºF caused by a fire. When the power supply is interrupted,
the energy stored in the spring of the fire damper actuator moves the damper blades back to its safe position. The damper
blades can be open again by pressing the reset button on ERL after the temperature cooled down below 165ºF.
140 Right to alterations reserved. SAFID is a registered trademark. © Copyright 2018. All rights reserved Right to alterations reserved. SAFID is a registered trademark. © Copyright 2018. All rights reserved 141
BLADE TYPE FIRE DAMPER BLADE TYPE FIRE DAMPER
Air Performance
Pressure Drop
The test method for pressure drop of Combination Fire/Smoke Damper was conducted as per ANSI / AMCA Standard 500-D,
Figure 5.3 which simulate the actual site condition when installed in ventilation, supply and return air conditioning ductworks.
Blade type fire dampers with the following SAFID blade type fire damper, galvanized steel
Order Code MFD-80 - 100 - 3V - PB - R - A1S - V1 - ER / 500 x 500 specifications shall be used in Heating, Ventilating and construction, 3V groove blade for parallel blades
Air Conditioning (HVAC) duct systems passing through operation, 500mm width X 500mm height duct size
openings in masonry walls, concrete floor slabs, and and right hand side external controls. Damper shall
in gypsum walls or partitions which required to have be with factory installed sleeve and 230 VAC BELIMO
Variants Duct Size a fire resistance rating to restrict the spread of fire. actuator with built-in auxiliary switch and with
MFD-40 = Sleeve Type Width x Height It shall be also used in Smoke Proof Stair Enclosure thermoelectric tripping device (ERL) with temperature
MFD-50 = Circular Spigot or Diameter. All if the wall penetrations required to be fire rated in rating of 165°F (74°C).
MFD-60 = Oval Spigot damper’s spigot sizes accordance with NFPA 90A Standard for Installation
MFD-80 = Factory Installed (slip-in type) will be of Air Conditioning and Ventilating Systems, and with Make: SAFID
Sleeve manufactured less NFPA 101 Life Safety Code. Type: MFD-80-100-3V-PB-R-A1S-V2-ERL
than duct size to fit Size: 500 W x 500 H
Types inside the ductwork Blade type fire dampers shall be tested and classified Qty: 1
100 = Galvanized Steel connections. by Underwriters Laboratories Inc. (UL) in accordance
Construction with the standards; UL 555 Standard for Safety, Fire
110 = Blades of Stainless Steel Type of Sensor Dampers.
Grade 304 ERL = Thermoelectric
Optional: Grade 316 or 316L Tripping Device Blade type fire dampers with Fire Resistance Rating
120 = Stainless Steel Construction Model: BAE165 US, of 1½ hour shall be used in fire barrier with Fire
S/S Grade 304 SF74 (165 °F Klixon) Resistance Rating of less than 3 hours, and dampers
Optional: Grade 316 or 316L with 3 hours Fire Resistance Rating shall be used in fire
Power Supply barrier with Fire Resistance Rating of 3 hours or more.
Types of Blades V1 = 24 VAC
3V = V Groove Type V2 = 230 VAC The fire dampers shall be fitted with UL Listed spring
return actuator and Thermoelectric Tripping Device
Linkage (ERL) with temperature rating of 165°F (74°C). ERL
PB = Slide Linkage Parallel shall cut-off power supply to the actuator in case of
Blades Operation fire that will activate the built-in spring return to close
the damper blades.
External Controls
R = Right Hand (Standard Supply) Damper blades shall be with external linkage and
L = Left Hand parallel action, Ga.16 galvanized steel with 3V groove
type for longitudinal reinforcement. Blade’s tip seal
Actuators shall be Type 60 Durometer Dense Silicone, meets
BELIMO, BF-S-ME gasket requirements in accordance with UL 555S.
BLADE T YPE FIRE DAMPERS
144 Right to alterations reserved. SAFID is a registered trademark. © Copyright 2018. All rights reserved Right to alterations reserved. SAFID is a registered trademark. © Copyright 2018. All rights reserved 145
BLADE TYPE FIRE DAMPER BLADE TYPE FIRE DAMPER
FD 30 - 100 FD SERIES
FLANGE TYPE FD SERIES [FD 30 - 100, FD 30 - 110, FD 30 - 120]
Dimensions
Spring: 800
Stainless steel closure spring mounted internally with 850
catch device to prevent blades from opening until 900
manually released. Parallel Blade (PB)
950
1000
146 Right to alterations reserved. SAFID is a registered trademark. © Copyright 2018. All rights reserved Right to alterations reserved. SAFID is a registered trademark. © Copyright 2018. All rights reserved 147
SLEEVE TYPE BLADE TYPE FIRE DAMPER SLEEVE TYPE BLADE TYPE FIRE DAMPER
FD 40 - 100 FD SERIES
SLEEVE TYPE FD SERIES [FD 40 - 100, FD 40 - 110, FD 40 - 120]
Dimensions
FD 40 - 110
Standard Construction General construction as type FD 40 - 100 damper but
blades, shafts and blade to spindle fixing in stainless
Frame: steel (Grade 304). Sleeve Type Standard Sizes
100mm x 40mm x 1.5mm (16 ga.) galvanized steel,
structurally designed hat section. Width (mm) Height (mm) No. of Blades
FD 40 -1 20
Blades: General construction as type FD 40 - 100 damper but with 100 200 1
300mm max. width,1.5mm (16 ga.) galvanized steel. case, blades shafts and blade to shaft fixing and linkage 150 250 1
all from stainless steel (Grade 304).
200 300 1
Finish:
BLADE T YPE FIRE DAMPERS
148 Right to alterations reserved. SAFID is a registered trademark. © Copyright 2018. All rights reserved Right to alterations reserved. SAFID is a registered trademark. © Copyright 2018. All rights reserved 149
CIRCULAR SPIGOT TYPE BLADE TYPE FIRE DAMPER CIRCULAR SPIGOT TYPE BLADE TYPE FIRE DAMPER
FD 50 - 100 FD SERIES
CIRCULAR SPIGOT TYPE FD SERIES [FD 50 - 100, FD 50 - 110, FD 50 - 120]
Dimensions
Spring:
Stainless steel closure spring mounted internally with
catch device to prevent blades from opening until
manually released.
Parallel Blade (PB)
150 Right to alterations reserved. SAFID is a registered trademark. © Copyright 2018. All rights reserved Right to alterations reserved. SAFID is a registered trademark. © Copyright 2018. All rights reserved 151
OVAL SPIGOT TYPE BLADE TYPE FIRE DAMPER OVAL SPIGOT TYPE BLADE TYPE FIRE DAMPER
FD 60 - 100 FD SERIES
OVAL SPIGOT TYPE FD SERIES [FD 60 - 100, FD 60 - 110, FD 60 - 120]
Dimensions
FD 60 - 110
Standard Construction General construction as type FD 60 - 100 damper but
blades, shafts and blade to spindle fixing in stainless
Frame (Spigot Type): steel (Grade 304). Oval Spigot Type Standard Sizes
180mmx1.5mm (16 ga) galvanized steel, L=405mm.
Width (mm) Height (mm) No. of Blades
Blades: FD 60 - 120
250mm max. width,1.5mm (16 ga.) galvanized steel. General construction as type FD 60 - 100 damper but with 300 200 1
case, blades shafts and blade to shaft fixing and linkage 350 250 1
Finish: all from stainless steel (Grade 304).
400 300 2
Mill galvanized.
BLADE T YPE FIRE DAMPERS
Spring: 1000
Stainless steel closure spring mounted internally with
catch device to prevent blades from opening until
Parallel Blade (PB)
manually released.
152 Right to alterations reserved. SAFID is a registered trademark. © Copyright 2018. All rights reserved Right to alterations reserved. SAFID is a registered trademark. © Copyright 2018. All rights reserved 153
RECTANGULAR SPIGOT TYPE RECTANGULAR SPIGOT TYPE
BLADE TYPE FIRE DAMPER BLADE TYPE FIRE DAMPER
FD 70 - 100 FD SERIES
RECTANGULAR SPIGOT TYPE FD SERIES [FD 70 - 100, FD 70 - 110, FD 70 - 120]
Dimensions
FD 70 - 110
Standard Construction General construction as type FD 70 - 100 damper but
blades, shafts and blade to spindle fixing in stainless
Frame (Spigot Type): steel (Grade 304). Rectangular Spigot Type Standard Sizes
180mmx1.5mm (16 ga) galvanized steel, L=405mm.
Width (mm) Height (mm) No. of Blades
Blades: FD 70 - 120
300mm max. width,1.5mm (16 ga.) galvanized steel. General construction as type FD 70 - 100 damper but with 100 200 1
case, blades shafts and blade to shaft fixing and linkage 150 250 1
Finish: all from stainless steel (Grade 304).
200 300 1
Mill galvanized.
BLADE T YPE FIRE DAMPERS
Spring: 800
Stainless steel closure spring mounted internally with 850
catch device to prevent blades from opening until 900
manually released. Parallel Blade (PB) 950
1000
154 Right to alterations reserved. SAFID is a registered trademark. © Copyright 2018. All rights reserved Right to alterations reserved. SAFID is a registered trademark. © Copyright 2018. All rights reserved 155
INSTALLATION DETAILS INSTALLATION DETAILS
Installation Details with Sleeve and Peripheral Angle Installation Details with HEVAC Frame
Linkage
BLADE T YPE FIRE DAMPERS
B2 Stainless steel
158 Right to alterations reserved. SAFID is a registered trademark. © Copyright 2018. All rights reserved Right to alterations reserved. SAFID is a registered trademark. © Copyright 2018. All rights reserved 159
COMBINATION
FIRE & SMOKE
DAMPERS
COMBINATION FIRE & SMOKE DAMPERS
UL File No.: R22165 and linkage brackets with axle in stainless steel Grade
304. Stub Shaft (Latch):
Die pressed galvanized steel sheet, 58mm x 68mm x
1.5mm thick (Ga.16).
Optional: Blades from stainless steel Grade 316 or
316L.
Bearings:
Sintered bronze oilite type.
1. Sleeve Type, Model: CFSD - 40 - 110
2. Circular Type, Model: CFSD - 50 - 110 Side Seal (Jamb Seal):
3. Oval Type, Model: CFSD - 60 - 110 Compression type SS grade 304, 0.3mm thick.
4. With factory installed Sleeve, Model: CFSD - 80 - 110
Blade Tip Seal:
Same as the standard construction but frame, blades, Blade tip seals are high temperature Durometer Dense
Product Description installation sleeve and all accessories in stainless steel Silicone.
Grade 304.
Jack Shaft:
Combination fire and smoke dampers provide an Optional: Frame, blades and installation sleeve from GI rod Ø12mm across the blade length with 10mm square
stainless steel Grade 316 or 316L. end x 25mmL to suit actuator.
automatic means of localizing areas of smoke and or
fire in ventilation systems that is greatly contribute to
1. Sleeve Type, Model: CFSD - 40 - 120 Jack Shaft Holder:
the safety of life and property in the early stage of fire.
2. Circular Type, Model: CFSD - 50 - 120 Die pressed GI steel 152.9mm x 82.2mm x 1.5mm thick with
COMBINATION FIRE & SMOKE DAMPERS
162 Right to alterations reserved. SAFID is a registered trademark. © Copyright 2018. All rights reserved Right to alterations reserved. SAFID is a registered trademark. © Copyright 2018. All rights reserved 163
COMBINATION FIRE SMOKE DAMPERS COMBINATION FIRE SMOKE DAMPERS
Types Types
DIA + 25
DIA + 25
W-5
H-5
Flat Oval Tyoe
COMBINATION FIRE & SMOKE DAMPERS
Model: CFSD - 60
1. Casing (Frame)
2. Linkage Bracket
3. Blade
4. Linkage Bar H-3
5. Bearings
6. Blade Stop
7. Side Seal
8. Blade Tip Seal W-3
164 Right to alterations reserved. SAFID is a registered trademark. © Copyright 2018. All rights reserved Right to alterations reserved. SAFID is a registered trademark. © Copyright 2018. All rights reserved 165
COMBINATION FIRE SMOKE DAMPERS COMBINATION FIRE SMOKE DAMPERS
CFSD with Factory Installed Sleeve, ERL and Actuator CFSD With Factory Installed Sleeve, ERL and Actuator
Model: CFSD-80 Model: CFSD - 80
Height: Up to 220 mm
166 Right to alterations reserved. SAFID is a registered trademark. © Copyright 2018. All rights reserved Right to alterations reserved. SAFID is a registered trademark. © Copyright 2018. All rights reserved 167
COMBINATION FIRE SMOKE DAMPERS COMBINATION FIRE SMOKE DAMPERS
CFSD with Factory Installed Sleeve, ERL and Actuator CFSD With Factory Installed Sleeve, ERL and Actuator
Model: CFSD-80 Model: CFSD - 80
Height: Up to 914 mm Width: Up to 1200 mm
Height: Up to 914 mm
A. Single section damper with two position (open/close) spring retrun type actuators:
Schedule of Damper Sizes and Actuator Types
1. BELIMO Model: FSLF-S-US (24 / 230VAC) with built-in auxiliary switch.
A. Multiple section damper with two position (open/close) spring retrun type actuators:
Torque: 3.5 Nm
Damper size: W=610mm maximum, H=406mm maximum
1. Model: MS4620F1203 (230VAC) with built-in auxiliary switch.
2. Model: MS8104F1210/MS4604F1210 (24 / 230VAC) with built-in auxiliary switch.
MS8120F1200 (24VAC) with built-in auxiliary switch.
Torque: 3.5 Nm
Torque: 20 Nm
Damper size: W=610mm maximum, H=406mm maximum
3. BELIMO Model: FSNF-S-US (24 / 230VAC) with built-in auxiliary switch.
Note: Location of the actuator can be INSIDE or OUTSIDE the airstream.
Torque: 8 Nm
Refer to technical data sheet of actuator or contact SAFID for the actuator specifications.
Damper size: W=610mm maximum, H=610mm maximum
4. BELIMO Model: BF-S-ME (24 / 230VAC) with built-in auxiliary swith.
Torque: 15 Nm
Damper size: W= 914mm maximum, H= 914mm maximum
Refer to technical data sheet of actuator or contact SAFID for the actuator specifications.
168 Right to alterations reserved. SAFID is a registered trademark. © Copyright 2018. All rights reserved Right to alterations reserved. SAFID is a registered trademark. © Copyright 2018. All rights reserved 169
COMBINATION FIRE SMOKE DAMPERS COMBINATION FIRE SMOKE DAMPERS
CFSD with Factory Installed Sleeve, ERL and Actuator CFSD With Factory Installed Sleeve, ERL and Actuator
Model: CFSD - 80 Model: CFSD - 80
Width: Up to 1828 mm Width: Up to 1200 mm
Height: Up to 914 mm Height: Up to 1828 mm
170 Right to alterations reserved. SAFID is a registered trademark. © Copyright 2018. All rights reserved Right to alterations reserved. SAFID is a registered trademark. © Copyright 2018. All rights reserved 171
COMBINATION FIRE SMOKE DAMPERS INSTALLATION DETAILS
CFSD with Factory Installed Sleeve, ERL and Actuator CFSD With Factory Installed Sleeve, ERL and Actuator
Model: CFSD - 80 Model: CFSD - 80
Width: Up to 1828 mm
Height: Up to 1828 mm
Typical Installation
A. Multiple section damper with two position (open/close) spring retrun type actuators: 1. Airflow can be at opposite direction.
2. The actuator and ERL can be located in either side of the wall.
1. Model: MS4620F1203 (230VAC) with built-in auxiliary switch.
3. Refer to installation manual for further installation detail.
MS8120F1200 (24VAC) with built-in auxiliary switch.
Torque: 20 Nm
Note: Location of the actuator can be INSIDE or OUTSIDE the airstream.
Refer to technical data sheet of actuator or contact SAFID for the actuator specifications.
172 Right to alterations reserved. SAFID is a registered trademark. © Copyright 2018. All rights reserved Right to alterations reserved. SAFID is a registered trademark. © Copyright 2018. All rights reserved 173
ACTUATORS AIR PERFORMANCE
Pressure Drop
The test method for pressure drop of Combination Fire/Smoke Damper was conducted as per ANSI/AMCA Standard 500-D,
Figure 5.3 which simulate the actual site condition when installed in ventilation, supply and return air conditioning ductworks.
174 Right to alterations reserved. SAFID is a registered trademark. © Copyright 2018. All rights reserved Right to alterations reserved. SAFID is a registered trademark. © Copyright 2018. All rights reserved 175
ORDER REFERENCE DETAILS ORDER REFERENCE DETAILS
Combination fire and smoke dampers with the SAFIDS’s combination fire and smoke dampers,
following specifications shall be used in Heating, galvanized steel construction, 3V groove blade for
Order Code CFSD-80 - 100 - 3V - PB - R - A1S - V1 - ER / 500 x 500 Ventilating and Air Conditioning (HVAC) duct systems parallel blades operation, 500mm width X 500mm
passing through openings in masonry walls, concrete height duct size and right hand side external controls.
floor slabs, and in gypsum walls or partitions which Damper shall be with factory installed sleeve and 230
required to have a fire resistance rating to restrict the VAC BELIMO actuator with built-in auxiliary switch
Variants Duct Size spread of fire. It shall be also used in Smoke Control and with thermoelectric tripping device (ERL) with
CFSD-40 = Sleeve Type Width x Height Systems and in Smoke Proof Stair Enclosure if the wall temperature rating of 165°F (74°C).
CFSD-50 = Circular Spigot or Diameter. All penetrations required to be fire rated in accordance
CFSD-60 = Oval Spigot damper’s spigot sizes with NFPA 90A Standard for Installation of Air Make: SAFID
CFSD-80 = Factory Installed (slip-in type) will be Conditioning and Ventilating Systems, and with NFPA Type: CFSD-80-100-3V-PB-R-A1S-V2-ERL
Sleeve manufactured less 101 Life Safety Code. Size: 500 W x 500 H
than duct size to fit Qty: 1
Types inside the ductwork Combination fire and smoke dampers shall be tested
100 = Galvanized Steel connections. and classified by Underwriters Laboratories Inc. (UL)
Construction in accordance with the standards; UL 555 Standard for
110 = Blades of Stainless Steel Type of Sensor Safety, Fire Dampers and UL 555S Standard for Safety,
Grade 304 ERL = Thermoelectric Smoke Dampers.
Optional: Grade 316 or 316L Tripping Device
120 = Stainless Steel Construction Model: BAE165 US, Combination fire and smoke dampers with Fire
S/S Grade 304 SF74 (165 °F Klixon) Resistance Rating of 1½ hour shall be used in fire
Optional: Grade 316 or 316L barrier with Fire Resistance Rating of less than 3
Power Supply hours, and dampers with 3 hours Fire Resistance
Types of Blades V1 = 24 VAC Rating shall be used in fire barrier with Fire Resistance
3V = V Groove Type V2 = 230 VAC Rating of 3 hours or more. Leakage Resistance Rating
shall be Class I at 350°F or Class II at 250°F elevated
Linkage temperature. It shall be UL Certified for dynamic
PB = Slide Linkage Parallel closure test with airflow velocity of minimum 2000
COMBINATION FIRE & SMOKE DAMPERS
176 Right to alterations reserved. SAFID is a registered trademark. © Copyright 2018. All rights reserved Right to alterations reserved. SAFID is a registered trademark. © Copyright 2018. All rights reserved 177
FLANGE TYPE COMBINATION FIRE SMOKE DAMPER FLANGE TYPE COMBINATION FIRE SMOKE DAMPER
Dimensions
Description Seals:
Side seal are compession type stainless steel grade 304
Combination fire and smoke dampers type, FSD 30 to close gap between case & blades.
provide an automatic means of localizing areas of
smoke and/or fire in ventilation systems. It prevent the Minimum Size:
distribution of fire and/or smoke through ventilation 150 x 150mm, dampers up to 250mm high is single blade
ductworks. FSD offer an effective barrier maintaining construction.
integrity in a fire situation and this is combined with
low leakage characteristic for smoke management. It Maximum Size:
is suitable for installation in sheet metal ductworks or 1000 x 1000mm, as single section.
in walls or ceiling slabs made from concrete, brick and Multiple section assembly with unlimited size, where each
lightweight partition walls. section operates independently.
178 Right to alterations reserved. SAFID is a registered trademark. © Copyright 2018. All rights reserved Right to alterations reserved. SAFID is a registered trademark. © Copyright 2018. All rights reserved 179
SLEEVE TYPE COMBINATION FIRE SMOKE DAMPER SLEEVE TYPE COMBINATION FIRE SMOKE DAMPER
Dimensions
Description Seals:
Side seal are compession type stainless steel grade 304
Combination fire and smoke dampers type, FSD 40 to close gap between case and blades.
provide an automatic means of localizing areas of
smoke and/or fire in ventilation systems. It prevent the Minimum Size:
distribution of fire and/or smoke through ventilation 200 x 200mm, damper up to 300mm high is single blade
ductworks. FSD offer an effective barrier maintaining construction.
integrity in a fire situation and this is combined with
low leakage characteristic for smoke management. It Maximum Size:
is suitable for installation in sheet metal ductworks or 1000 x 1000mm, as single section.
in walls or ceiling slabs made from concrete, brick and Multiple section assembly with unlimited size, where each
lightweight partition walls. section operates independently.
180 Right to alterations reserved. SAFID is a registered trademark. © Copyright 2018. All rights reserved Right to alterations reserved. SAFID is a registered trademark. © Copyright 2018. All rights reserved 181
CIRCULAR SPIGOT TYPE COMBINATION CIRCULAR SPIGOT TYPE COMBINATION
FIRE SMOKE DAMPER FIRE SMOKE DAMPER
Dimensions
FSD 50 - 110
Standard Construction General construction as type FSD 50 - 100 damper but
COMBINATION FIRE & SMOKE DAMPERS
182 Right to alterations reserved. SAFID is a registered trademark. © Copyright 2018. All rights reserved Right to alterations reserved. SAFID is a registered trademark. © Copyright 2018. All rights reserved 183
OVAL SPIGOT TYPE COMBINATION FIRE OVAL SPIGOT TYPE COMBINATION FIRE
SMOKE DAMPER SMOKE DAMPER
Dimensions
FSD 60 - 110
Standard Construction General construction as type FSD 60 - 100 damper but
COMBINATION FIRE & SMOKE DAMPERS
184 Right to alterations reserved. SAFID is a registered trademark. © Copyright 2018. All rights reserved Right to alterations reserved. SAFID is a registered trademark. © Copyright 2018. All rights reserved 185
RECTANGULAR SPIGOT TYPE COMBINATION RECTANGULAR SPIGOT TYPE COMBINATION
FIRE SMOKE DAMPER FIRE SMOKE DAMPER
Dimensions
Description Seals:
Side seal are compession type stainless steel grade 304
Combination fire and smoke dampers type, FSD 70 to close gap between case and blades.
provide an automatic means of localizing areas of
smoke and/or fire in ventilation systems. It prevent the Minimum Size:
distribution of fire and/or smoke through ventilation 200 x 200mm, damper up to 250mm high is single blade
ductworks. FSD offer an effective barrier maintaining construction.
integrity in a fire situation and this is combined with
low leakage characteristic for smoke management. It Maximum Size:
is suitable for installation in sheet metal ductworks or 1000 x 1000mm, as single section.
in walls or ceiling slabs made from concrete, brick and Multiple section assembly with unlimited size, where each
lightweight partition walls. section operates independently.
200 200 1
Finish: FSD 70 - 120
Mill galvanized. 250 250 1
General construction as type FSD 70 - 100 damper but with
300 300 2
case, blades shafts and blade to shaft fixing and linkage
Linkage: all from stainless steel (Grade 304). 350 350 2
Parallel blade have standard face linkage, parallel blade 400 400 2
operation is standard.
450 450 3
Linkage consist of 6mm dia. S/S steel pivot pins.
500 500 3
Case Bearings: 550 600 4
Made sintered bronze (oilite), operational temp. 600 700 4
resistanace up to 200 ˚C. 650 800 5
700 900 6
Fusible Link:
750 1000 6
Standard release 74 ˚C. (165 ˚F) is std. (UL listed)
Other temperatures available on request. 800
850
Axles & Control Shaft: 900
12mm diameter zinc plated mild steel. 950
1000
186 Right to alterations reserved. SAFID is a registered trademark. © Copyright 2018. All rights reserved Right to alterations reserved. SAFID is a registered trademark. © Copyright 2018. All rights reserved 187
MATERIALS CONSTRUCTION MATERIALS CONSTRUCTION
For Sleeve Type Only Damper with Mounting Bracket for Actuator 1 -Bracket Case Mounted 2 - Shaft Bearing 3 - Through Shaft 4 -Coil Spring
5 -Fixed Link Arm 6 - Free Link Arm 7 - Blade Rotation Ink 8 -Fuse Link
9 -Connecting Link Arm 10 - Shaft Joint 11 - Drive Spindle
188 Right to alterations reserved. SAFID is a registered trademark. © Copyright 2018. All rights reserved Right to alterations reserved. SAFID is a registered trademark. © Copyright 2018. All rights reserved 189
INSTALLATION DETAILS INSTALLATION DETAILS
100 100 1 2
150 150 2 2
200 200 2 2
250 250 2 3
300 300 3 3
350 350 3 4
400 400 4 4
450 450 4 4
500 500 4 5
600 600 5 6
700 700 6 6
800 800 7 7
900 900 8 8
1000 1000 8 9
1100 1100 9 10
1200 1200 10 10
1300 11
1400 12
1500 13
1600 14
1700 14
1800 15
190 Right to alterations reserved. SAFID is a registered trademark. © Copyright 2018. All rights reserved Right to alterations reserved. SAFID is a registered trademark. © Copyright 2018. All rights reserved 191
INSTALLATION DETAILS PRODUCT RANGE
FSD 50
Seals Belimo Actuators
S3 Combination of S1 & S2, fitted A10 AF24-S US spring return with limit switch
to close gap between frame and
blades and blade edge seals to A11 AF24-SR spring return
seal blade to blade joint. Blade
seals is silicone rubber with A12 NF24 US spring return
FSD 60 FSD 70 temperature resistance up to
COMBINATION FIRE & SMOKE DAMPERS
A13
192 Right to alterations reserved. SAFID is a registered trademark. © Copyright 2018. All rights reserved Right to alterations reserved. SAFID is a registered trademark. © Copyright 2018. All rights reserved 193
ORDER REFERENCE DETAILS
CFSD Series
Variants Actuator
*FSD30 = Flange (See page 193)
(Standard Supply)
FSD40 = Sleeve Duct Size
FSD50 = Circular Spigot - Square or rectangular
FSD60 = Oval Spigot dimension ‘W’ x ‘H’ mm
FSD70 = Rectangular Spigot circular ‘D’ mm dia.
- Flat oval ‘W’ x ‘H’ mm.
Type - All dampers spigots are
*100 (Standard Supply) manufactured down
110 on duct size to fit inside
120 ductwork connections.
194 Right to alterations reserved. SAFID is a registered trademark. © Copyright 2018. All rights reserved Right to alterations reserved. SAFID is a registered trademark. © Copyright 2018. All rights reserved 195
SMOKE
DAMPERS
SMOKE DAMPERS
SMOKE DAMPERS
196 Right to alterations reserved. SAFID is a registered trademark. © Copyright 2018. All rights reserved Right to alterations reserved. SAFID is a registered trademark. © Copyright 2018. All rights reserved 197
SMOKE DAMPERS SMOKE DAMPERS
SMOKE DAMPERS
Air Leakage Test: Class I and Class II
Smoke dampers willl be controlled by an automatic Blades: Elevated Temp. Test: 350°F and 250°F
alarm initiating device which is interlocked with damper 1.5mm thick (Ga.16) galvanized steel “Triple Vee” (3V) Dynamic Closure Test: Rated at 2000 FPM and
actuator. The Smoke dampers do not need to be groove type (standard).
4000 FPM Air Velocity
equipped with a fusible link or tripping device. Rated Pressure: Tested to 4.5 inch W.G. and rated at
Blade Stop:
4 inch W.G.
In today’s life safety products markets, many building 1.5mm thick (Ga.16) galvanized steel sheet bend at 45°
code require smoke dampers to be inspected for proper angle.
198 Right to alterations reserved. SAFID is a registered trademark. © Copyright 2018. All rights reserved Right to alterations reserved. SAFID is a registered trademark. © Copyright 2018. All rights reserved 199
SMOKE DAMPERS SMOKE DAMPERS
Types Types
DIA - 3
DIA + 25
DIA + 25
W-5
H-5
SMOKE DAMPERS
9. Lock Washer and GI Round Washer
10. Kneelock W-3
11. Jackshaft
W + 25 H + 25
200 Right to alterations reserved. SAFID is a registered trademark. © Copyright 2018. All rights reserved Right to alterations reserved. SAFID is a registered trademark. © Copyright 2018. All rights reserved 201
SMOKE DAMPERS SMOKE DAMPERS
A. Single section damper with two position (open/close) spring retrun type actuators:
1. Damper Frame 9. Auxiliary Switch Cable for Indicating Damper Blades
2. Sleeve Position 1. BELIMO Model: FSLF-S-US (24 / 230VAC) with built-in auxiliary switch.
3. Blade 10. Power Supply Torque: 3.5Nm for W = 610 mm maximum.
4. Linkage Bracket 11. Blade Stop 2. Model: MS8104F1210 / MS4604F1210 (24 / 230VAC) with built-in auxiliary switch.
5. Lock Washer and Galvanized Round Washer 12. Stainless Steel Side Seal Torque: 3.5Nm for W = 610 mm maximum.
3. BELIMO Model: BF-S-ME (24 / 230VAC) with built-in auxiliary swith.
6. Kneelock 13. Blade Tip Seal
Torque: 15 Nm for W = 914 mm maximum.
SMOKE DAMPERS
SMOKE DAMPERS
7. Linkage Bar 14. Jackshaft
8. Actuator 15. Axle
16. Bearing
Refer to technical data sheet of actuator or contact SAFID for the actuator specifications.
202 Right to alterations reserved. SAFID is a registered trademark. © Copyright 2018. All rights reserved Right to alterations reserved. SAFID is a registered trademark. © Copyright 2018. All rights reserved 203
SMOKE DAMPERS SMOKE DAMPERS
SD With Factory Installed Sleeve and Actuator SD With Factory Installed Sleeve and Actuator
Model: SD - 80 Model: SD - 80
Height: Up to 914 mm Width: Up to 1200 mm
Height: Up to 914 mm
A. Single section damper with two position (open/close) spring retrun type actuators:
Schedule of Damper Sizes and Actuator Types
1. BELIMO Model: FSLF-S-US (24 / 230VAC) with built-in auxiliary switch.
Torque: 3.5 Nm
Damper size: W=610mm maximum, H=406mm maximum A. Multiple section damper with two position (open/close) spring retrun type actuators:
2. Model: MS8104F1210/MS4604F1210 (24 / 230VAC) with built-in auxiliary switch.
Torque: 3.5 Nm 1. Model: MS4620F1203 (230VAC) with built-in auxiliary switch.
Damper size: W=610mm maximum, H=406mm maximum MS8120F1200 (24VAC) with built-in auxiliary switch.
3. BELIMO Model: FSNF-S-US (24 / 230VAC) with built-in auxiliary switch. Torque: 20 Nm
Torque: 8 Nm
SMOKE DAMPERS
SMOKE DAMPERS
Damper size: W=610mm maximum, H=610mm maximum Note: Location of the actuator can be INSIDE or OUTSIDE the airstream.
4. BELIMO Model: BF-S-ME (24 / 230VAC) with built-in auxiliary swith. Refer to technical data sheet of actuator or contact SAFID for the actuator specifications.
Torque: 15 Nm
Damper size: W= 914mm maximum, H= 914mm maximum
Refer to technical data sheet of actuator or contact SAFID for the actuator specifications.
204 Right to alterations reserved. SAFID is a registered trademark. © Copyright 2018. All rights reserved Right to alterations reserved. SAFID is a registered trademark. © Copyright 2018. All rights reserved 205
SMOKE DAMPERS SMOKE DAMPERS
SD With Factory Installed Sleeve and Actuator SD With Factory Installed Sleeve and Actuator
Model: SD - 80 Model: SD - 80
Width: Up to 1828 mm Width: Up to 1200 mm
Height: Up to 914 mm Height: Up to 1828 mm
A. Multiple section damper with two position (open/close) spring retrun type actuators:
SMOKE DAMPERS
Refer to technical data sheet of actuator or contact SAFID for the actuator specifications.
1. Model: MS4620F1203 (230VAC) with built-in auxiliary switch.
MS8120F1200 (24VAC) with built-in auxiliary switch.
Torque: 20 Nm
Note: Location of the actuator can be INSIDE or OUTSIDE the airstream.
Refer to technical data sheet of actuator or contact SAFID for the actuator specifications.
206 Right to alterations reserved. SAFID is a registered trademark. © Copyright 2018. All rights reserved Right to alterations reserved. SAFID is a registered trademark. © Copyright 2018. All rights reserved 207
SMOKE DAMPERS INSTALLATION DETAILS
Notes:
A. Multiple section damper with two position (open/close) spring retrun type actuators:
1. Airflow can be at opposite direction.
1. Model: MS4620F1203 (230VAC) with built-in auxiliary switch. 2. The actuator can be located in either side of the wall.
MS8120F1200 (24VAC) with built-in auxiliary switch. 3. Refer to installation manual for further installation detail.
SMOKE DAMPERS
SMOKE DAMPERS
Torque: 20 Nm
The Smoke Damper will be installed at the smoke barrier penetrations in accordance with NFPA 90A.
Note: Location of the actuator can be INSIDE or OUTSIDE the airstream.
Refer to technical data sheet of actuator or contact SAFID for the actuator specifications.
208 Right to alterations reserved. SAFID is a registered trademark. © Copyright 2018. All rights reserved Right to alterations reserved. SAFID is a registered trademark. © Copyright 2018. All rights reserved 209
ACTUATORS AIR PERFORMANCE
Pressure Drop
The test method for the pressure drop of the Smoke Damper was conducted as per ANSI/AMCA Standard 500-D, Figure 5.3
which simulate the actual site condition when installed in ventilation, supply and return air conditioning ductworks.
SMOKE DAMPERS
Belimo Actuator Honeywell Actuator
Models: BF, FSNF and FSLF Model: MS4620F1203
210 Right to alterations reserved. SAFID is a registered trademark. © Copyright 2018. All rights reserved Right to alterations reserved. SAFID is a registered trademark. © Copyright 2018. All rights reserved 211
ORDER REFERENCE DETAILS ORDER REFERENCE DETAILS
Smoke dampers with the following specifications SAFID Smoke Damper, galvanized steel construction,
shall be used in Heating, Ventilating and Air 3V groove blade for parallel blades operation, 500mm
Order Code SD-80 - 100 - 3V - PB - R - A1S - V1 / 500 x 500
Conditioning (HVAC) Duct Systems passing through width x 500mm height duct size and right hand
openings in masonry walls, concrete floor slabs, and side external controls. Damper shall be with factory
in light partition walls designed as smoke barrier to installed sleeve and 230 VAC BELIMO actuator with
restrict the spread of smoke. It shall be also used built-in auxiliary switch.
Variants Duct Size
in Smoke Exhaust System and in Smoke Proof Stair
SD-40 = Sleeve Type Width x Height
Enclosure in accordance to NFPA 90A Standard Make: SAFID
SD-50 = Circular Spigot or Diameter. All
for Installation of Air Conditioning and Ventilating Type: SD-80-100-3V-PB-R-A1S-V2
SD-60 = Oval Spigot damper’s spigot sizes
Systems, and to NFPA 101 Life Safety Code. Size: 500 W x 500 H
SD-80 = Factory Installed (slip-in type) will be
Qty: 1
Sleeve manufactured less
Smoke dampers will be tested and classified by
than duct size to fit
Underwriters Laboratories Inc. (UL) in accordance
Types inside the ductwork
with the standards, UL 555S Standard for Safety,
100 = Galvanized Steel connections.
Smoke Dampers.
Construction
110 = Blades of Stainless Steel Power Supply
Smoke dampers will have a Leakage Resistance Rating
Grade 304 V1 = 24 VAC
of Class I at 350°F or Class II at 250°F elevated
Optional: Grade 316 or 316L V2 = 230 VAC
temperature. It shall be tested for heated air operation
120 = Stainless Steel Construction
test with air velocity of 2400 FPM to be rated at 2000
S/S Grade 304
FPM and the test pressure shall be 4.5 inch W.G. static
Optional: Grade 316 or 316L
pressure to be rated at 4 inch W. G. Pressure Class.
Types of Blades
Smoke Damper shall be fitted with UL Listed
3V = V Groove Type
BELIMO spring return actuator and shall be
controlled by smoke detector. The power supply to the
Linkage
actuator shall be cut-off as soon as the smoke detector
PB = Slide Linkage Parallel
detect the smoke.
Blades Operation
SMOKE DAMPERS
will be Ga.16 galvanized steel formed into hat channel
shape.
212 Right to alterations reserved. SAFID is a registered trademark. © Copyright 2018. All rights reserved Right to alterations reserved. SAFID is a registered trademark. © Copyright 2018. All rights reserved 213
FLANGE TYPE SMOKE DAMPER FLANGE TYPE SMOKE DAMPER
Dimensions
Flange Type
Standard Construction
Width (mm) Height (mm) No. of Blades
SMD 30 - 120
Frame: General construction as type SMD 30 - 100 damper but 100 100 1
160mm x 30mmx1.5mm (16 ga.) galvanized steel, with frame, blades shafts and blade to shaft fixing and
formed channel for flange connections. 150 150 1
linkage all from stainless steel (Grade 304).
200 200 1
Blades: 250 250 1
250mm max. width, 1.5mm (16 ga.) galvanized steel. 300 300 2
350 350 2
Finish:
400 400 2
Mill galvanized.
450 450 2
Linkage: 500 500 3
Side linkage concealed in frame for parallel blade 550 600 3
operation is standard. 600 700 4
Face linkage available (optional).
650 800 5
Linkage consist of 6mm dia. S/S pivot pins.
SMOKE DAMPERS
SMOKE DAMPERS
700 900 5
Parallel Blade (PB) 750
Case Bearings: 1000 6
Made of sintered bronze (oilite), operational temp. 800 1100 7
resistance up to 200 ˚C. 850 1200 7
900 1300 8
Axles and Control Shaft:
950 1400 9
12mm diameter zinc plated mild steel.
1000 1500 9
Minimum Size: 1050 1600 10
100 x 100mm, damper up to 250mm high is single 1100 1700 11
blade construction. 1200 1800 12
214 Right to alterations reserved. SAFID is a registered trademark. © Copyright 2018. All rights reserved Right to alterations reserved. SAFID is a registered trademark. © Copyright 2018. All rights reserved 215
SLEEVE TYPE SMOKE DAMPER SLEEVE TYPE SMOKE DAMPER
Dimensions
SMOKE DAMPERS
Case Bearings: Parallel Blade (PB) 750 1000 6
Made of sintered bronze (oilite), operational temp. 800 1100 6
resistance up to 200 ˚C. 850 1200 7
900 1300 8
Axles and Control Shaft:
950 1400 8
12mm diameter zinc plated mild steel.
1000 1500 9
Minimum Size: 1050 1600 10
100 x 100mm, damper up to 300mm high is single blade 1100 1700 11
construction. 1200 1800 12
1200
216 Right to alterations reserved. SAFID is a registered trademark. © Copyright 2018. All rights reserved Right to alterations reserved. SAFID is a registered trademark. © Copyright 2018. All rights reserved 217
CIRCULAR SPIGOT TYPE SMOKE DAMPER CIRCULAR SPIGOT TYPE SMOKE DAMPER
Dimensions
SMOKE DAMPERS
700 4
Case Bearings:
Made of sintered bronze (oilite), operational temp. 800 5
resistance up to 200 ˚C. 900 6
Parallel Blade (PB) 1000 7
Axles and Control Shaft:
12mm diameter zinc plated mild steel.
Minimum Size:
100 mm diameter, damper up to 250mm dia. is single blade
construction.
218 Right to alterations reserved. SAFID is a registered trademark. © Copyright 2018. All rights reserved Right to alterations reserved. SAFID is a registered trademark. © Copyright 2018. All rights reserved 219
OVAL SPIGOT TYPE SMOKE DAMPER OVAL SPIGOT TYPE SMOKE DAMPER
Dimensions
SMOKE DAMPERS
800 900 6
Case Bearings:
Made of sintered bronze (oilite), operational temp. Parallel Blade (PB) 850
resistance up to 200 ˚C. 900
950
Axles & Control Shaft: 1000
12mm diameter zinc plated mild steel.
Minimum Size:
200 x 100mm, damper up to 250mm high is single blade
construction.
220 Right to alterations reserved. SAFID is a registered trademark. © Copyright 2018. All rights reserved Right to alterations reserved. SAFID is a registered trademark. © Copyright 2018. All rights reserved 221
MATERIALS CONSTRUCTION MATERIALS CONSTRUCTION
For Sleeve Type Only Damper with Mounting Bracket for Actuator
SMOKE DAMPERS
900 900 8 8
1000 1000 8 9
1100 1100 9 10
1200 1200 10 10
1300 11
Note: Type S3 (Combination of S1 & S2) 1400 12
1500 13
1600 14
1700 14
1800 15
222 Right to alterations reserved. SAFID is a registered trademark. © Copyright 2018. All rights reserved Right to alterations reserved. SAFID is a registered trademark. © Copyright 2018. All rights reserved 223
INSTALLATION DETAILS PRODUCT RANGE
For Sleeve type, SMD 40 Circular Type, SMD 50 Seals Belimo Actuators
S3 Combination of S1 & S2, fitted A10 AF24-S US spring return with limit switch
to close gap between frame and
blades and blade edge seals to A11 AF24-SR spring return
seal blade to blade joint. Blade
seals is silicone rubber with A12 NF24 US spring return
temperature resistance up to
175 ˚C, for ultra low leakage A13 NF120 US spring return
characteristic.
A14 NF24-S US spring return with limit switch
Oval type SMD 60
A15 NF120-S US spring return with limit switch
SMOKE DAMPERS
A23 GM240 open/closed
224 Right to alterations reserved. SAFID is a registered trademark. © Copyright 2018. All rights reserved Right to alterations reserved. SAFID is a registered trademark. © Copyright 2018. All rights reserved 225
ORDER REFERENCE DETAILS
SD Series
Variants Actuators
*SMD 30 = Flange (Standard Supply) (See page 225)
SMD 40 = Sleeve
SMD 50 = Circular Spigot Duct Size
SMD 60 = Oval Spigot - Square or rectangular
Dimensions ‘W’ x ‘H’
Types mm.
*100 (Standard Supply) - Circular ‘D’ mm dia.
110 - Flat oval ‘W’ x ‘H’ mm.
120 - All damper spigots
are manufactured
Variants - Blade Operation down on duct size to fit
*PB = Side Linkage Parallel inside ductwork
(Standard Supply) connections.
Face Linkage (optional)
External Controls
Variants - Seals * “R” = Right Hand
S = None (not applicable) (Standard Supply)
S1 = Blade Seals Only (not applicable) “L” = Left Hand
S2 = Side Seal (not applicable)
*S3 = Side Seal & Blade Seals
(Standard Supply)
Variants - Bearings
*B1 = Sintered Bronze (oilite)
B2 = Stainless Steel
SMOKE DAMPERS
Rectangular, square, circular and flat oval Smoke Standard
Dampers designed for the smoke isolation of sections Make: SAFID
of ducting in ventilation systems. Flanged casing, shut Type: SMD 30 - 100 PB - S3 - B1 - R - 500x500 / A01
off blades with overlapping interlocking joints and Qty: 1
with side seals and blade seals for low leakage options
(when required). Blades are connected by side linkage
for parallel action and face linkage parallel action also
available.
226 Right to alterations reserved. SAFID is a registered trademark. © Copyright 2018. All rights reserved Right to alterations reserved. SAFID is a registered trademark. © Copyright 2018. All rights reserved 227
BELIMO
DAMPER
ACTUATORS
BELIMO DAMPER ACTUATORS
OPEN/CLOSE ACTUATOR [230V AC, 24V AC/DC] CODE: A1 CODE: A1S OPEN/CLOSE ACTUATOR [230V AC, 24V AC/DC]
BF 230-ME, BF 24-ME (SPRING-RETURN) BF 230-S-ME, BF 24-S-ME (SPRING-RETURN)
Mode of Operation: Technical Data BF 230-ME BF 24-ME Mode of Operation: Technical Data BF 230-S-ME BF 24-S-ME
The actuator moves the damper to its normal working The actuator moves the damper to its normal working
position while tensioning the return spring at the same Nominal Voltage AC 230 V, 50/60 Hz AC 24 V, 50/60 Hz/ position while tensioning the return spring at the same Nominal Voltage AC 230 V, 50/60 Hz AC 24 V, 50 60 Hz/
time. If the power supply is interrupted, the energy stored DC 24 V time. If the power supply is interrupted, the energy DC 24 V
in the spring moves the damper back to its safe position. stored in the spring moves the damper back to its safe
Nominal Voltage AC 198 - 264 V AC 19.2 - 28.8 V position. Nominal Voltage AC 198 - 264 V AC 19.2 - 28.8 V
Range DC 21.6 - 28.8 V Range DC 21.6 - 28.8 V
Manual Operations:
Without power supply, the damper can be operated Signalling:
Power Consumption Power Consumption
manually and fixed in any required position. Release of Two microswitches with fixed settings are installed in • Monitoring
• Monitoring 11 W @ nominal torque 8 W @ nominal torque 11 W @ nominal torque 8 W @ nominal torque
the locking mechanism can be achieved manually or the actuator for indicating the damper end positions. • Holding
• Holding 3.5 W 2W 3.5 W 2W
automatically by applying the supply voltage. The position of the damper blade can be read off on a • For
• For wire Sizing 12 VA / lmax. 500 11 VA / lmax. 8.3 A wire Sizing 12 VA / lmax. 500 11 VA / lmax. 8.3 A
mechanical position indicator.
mA @ 5 ms @ 5 ms mA @ 5 ms @ 5 ms
Dimensions Connecting Cable 1 m, 2 x 0.75 m2 (halogen-free) Manual Operation: Auxillary Switch 2 x SPDT
Without power supply, the damper can be operated • Contact Rating 1 mA... 6 A (3 A), DC 5 V - AC 250
Torque manually and fixed in any required position. Release of • Switching Points 5° / 80°
• Motor Min. 15 Nm the locking mechanism can be achieved manually or
• Spring-Return Min. 15 Nm Connecting
automatically by applying the supply voltage.
• Motor Cable 1 m, 2 x 0.75 mm2 (halogen-free)
Running Time • Auxiliary Switch Cable 1 m, 6 x 0.75 mm2 (halogen-free)
• Motor
Dimensions
< 75 s
• Spring-Return < 20 s (tamb = 20° C) Torque
• Motor Min. 15 Nm
Sound Power Level • Spring-Return Min. 15 Nm
• Motor Max. 45 dB (A)
• Spring-Return ~62 dB (A) Running Time
BELIMO DAMPER ACTUATORS
Maintenance Maintenance-free
230 Right to alterations reserved. SAFID is a registered trademark. © Copyright 2018. All rights reserved Right to alterations reserved. SAFID is a registered trademark. © Copyright 2018. All rights reserved 231
SPRING-RETURN OPEN CLOSE ACTUATOR SPRING-RETURN OPEN CLOSE ACTUATOR
FOR DAMPERS UP TO 3M² FOR DAMPERS UP TO 3M²
OPEN/CLOSE ACTUATOR [230V AC, 24V AC/DC] CODE: A01 & A02 CODE: A03 & A04 OPEN/CLOSE ACTUATOR [230V AC]
BF 230, BF 24 (SPRING-RETURN) AF 230, AF 230-S (SPRING-RETURN)
Connecting Cable -Motor 1m, 2 x 0.75 mm2 one adjustable auxiliary switch which allows angle of Switching Points fixed 5% , adjustable 26…89%
-Auxillary Swatches 1m, 6 x 0.75 mm2 rotation of 5% and between 26 - 89% to be signalled
Connecting Cable -Motor 1m, 2 x 0.75 mm2
Angle of Rotation 95° (including 5 spring pretensioning) *AF... - S -Auxillary Swatches 1m, 6 x 0.75 mm2
Damper Rotation 12mm form-fit (10mm with adapter supplied) Dimensions Angle of Rotation Max. 95˚ (adj. 26…95% with supplied limit stop).
232 Right to alterations reserved. SAFID is a registered trademark. © Copyright 2018. All rights reserved Right to alterations reserved. SAFID is a registered trademark. © Copyright 2018. All rights reserved 233
SPRING-RETURN OPEN CLOSE ACTUATOR SPRING-RETURN OPEN CLOSE ACTUATOR
FOR DAMPERS UP TO 3M² FOR DAMPERS UP TO 3M²
OPEN/CLOSE ACTUATOR [230V AC, 120V AC] CODE: A05 & A06 CODE: A07 & A08 OPEN/CLOSE ACTUATOR [230V AC, 120V AC]
AF 230, AF 120 US (SPRING-RETURN) AF 230-S, AF 120-S US (SPRING-RETURN)
Application: Technical Data AF 230 AF 120 US Application: Technical Data AF 230-S AF 120-S US
For on-off, fail-safe control of dampers in HVAC systems. For on-off, fail-safe control of dampers in HVAC systems.
Actuator sizing should be done in accordance with the Power Supply 230 VAC (+-) 14% 120 VAC (+-) 10% Actuator sizing should be done in accordance with the Power Supply 230 VAC (+-) 14% 120 VAC (+-) 10%
damper manufacturer’s specs. Control is on-off from an 50/60Hz damper manufacturer’s specs. Control is on-off from an 50/60Hz
auxillary contact, or a manual switch. auxillary contact, or a manual switch.
Power Consumption Power Consumption
• Monitoring running: 6.5 W 6W • Monitoring running: 6.5 W 6W
Mode of Operation: Mode of Operation:
• Holding holding: 2.5 W 2.3 W • Holding holding: 2.5 W 2.3 W
The AF series actuators provide true spring return The AF series actuators provide true spring return
operation for reliable fail-safe application and positive Transormer Sizing 11 VA 10 VA operation for reliable fail-safe application and positive Transormer Sizing 11 VA 10 VA
close off on air tight dampers. The spring return system close off on air tight dampers. The spring return system
provide consistent torque to the damper with and without Electrical Connection 3 ft, 18 GA appliance cable 1/2” conduit provide consistent torque to the damper with and without Electrical Connection 3 ft, 18 GA appliance cable 1/2” conduit
power applied to the actuator. connection. power applied to the actuator. connection.
Overload Protection electronic throughout 0 to 95˚ rotation. The actuators is provided with 2 built in auxiliary switches. Overload Protection Electronic throughout 0 to 95˚ rotation.
The SPDT switches are provided for safety interfacing or
Angle Rotation 95°, adjustable 30 to 95˚ w/ accessories Angle Rotation 95°, adjustable 30 to 95˚ w/ accessories
Dimensions signalling, for example for fan start up.
Torque 133 in-lb [15Nm] constant Torque 133 in-lb [15Nm] constant
Direction of Rotation Spring Return can be Selected by L/R Mounting. Direction of Rotation Spring Return can be Selected by L/R Mounting
Manual Override 3mm hex crank (shipped w/ actuator) Manual Override 3mm hex crank (shipped w/ actuator)
Running Time 150 sec. constant, independent of load, Auxiliary Switches 2xSPDT 7A (2.5A) @ 250 VAC, UL listed
spring return < 20 sec
AF...-S One set at +5˚, one adjustable 25˚ to 85˚.
Humidity 5 to 95% RH noncondensing
Running Time 150 sec. constant, independent of load,
BELIMO DAMPER ACTUATORS
Housing NEMA type 2 / IP54 Ambient Temperature -22 ˚F to 122 ˚F [-30 ˚C to +50 ˚C]
Housing Material Zinc coated steel Storage Temperature -40 ˚F to 175 ˚F [-40 ˚C to 80 ˚C]
Wiring Diagram Agency Listings UL 873 listed, CSA 4813 02 certified Housing NEMA type 2 / IP54
234 Right to alterations reserved. SAFID is a registered trademark. © Copyright 2018. All rights reserved Right to alterations reserved. SAFID is a registered trademark. © Copyright 2018. All rights reserved 235
SPRING-RETURN OPEN CLOSE ACTUATOR SPRING-RETURN OPEN CLOSE ACTUATOR
FOR DAMPERS UP TO 3M² FOR DAMPERS UP TO 3M²
OPEN/CLOSE ACTUATOR [24V] CODE: A09 CODE: A10 OPEN/CLOSE ACTUATOR [230V AC, 120V AC]
AF 24 US (SPRING-RETURN) AF 24-S US (SPRING-RETURN)
Angle Rotation 95°, adjustable 30 to 95° w/ accessories with 2 built in auxiliary switches. The SPDT switches are Angle Rotation 95°, adjustable 30 to 95° w/ accessories
provided for safety interfacing or signalling, for example
Torque 133 in-lb [15Nm] constant Torque
Dimensions for fan start up.
133 in-lb [15Nm] constant
Direction of Rotation Spring Return can be Selected by L/R Mounting. Direction of Rotation Spring Return can be Selected by L/R Mounting.
Position Indication Visual Indicator, -5˚ to 90˚ (-5˚ is spring return Dimensions Position Indication Visual Indicator, -5˚ to 90˚ (-5˚ is spring return
position). position).
Manual Override 3mm hex crank (shipped w/ actuator) Manual Override 3mm hex crank (shipped w/ actuator)
Running Time 150 sec. constant, independent of load, Auxiliary Switches 2xSPDT 7A (2.5A) @ 250 VAC, UL listed
spring return < 20 sec
AF24S One set at +5˚, one adjustable 25˚ to 85˚.
Humidity 5 to 95% RH noncondensing
Running Time 150 sec. constant, independent of load,
Ambient Temperature -22 ˚F to 122 ˚F [-30 ˚C to +50 ˚C] spring return < 20 sec
BELIMO DAMPER ACTUATORS
Housing NEMA type 2 / IP54 Ambient Temperature -22 ˚F to 122 ˚F [-30 ˚C to +50 ˚C]
Housing Material Zinc coated steel Storage Temperature -40 ˚F to 176 ˚F [-40 ˚C to 80 ˚C]
Agency Listings UL 873 listed, CSA 4813 02 certified Housing NEMA type 2 / IP54
236 Right to alterations reserved. SAFID is a registered trademark. © Copyright 2018. All rights reserved Right to alterations reserved. SAFID is a registered trademark. © Copyright 2018. All rights reserved 237
SPRING-RETURN MODULATING ACTUATOR SPRING-RETURN OPEN CLOSE ACTUATOR
FOR DAMPERS UP TO 3M² FOR DAMPERS UP TO 1.5M²
MODULATING ACTUATOR [24V] CODE: A11 CODE: A12 & 13 OPEN/CLOSE ACTUATOR [24V, 120C AC]
AF 24-SR (SPRING-RETURN) NF 24 US, NF 120 US (SPRING-RETURN)
Control: DC0 - 10V or 0 - 20V phase cut Technical Data AF 24-SR Application: Technical Data NF 24 US NF 120 US
Position Feedback: DC2 - 10V For on-off, fail-safe control of dampers in HVAC systems.
Manual operation with integral position stop Power Supply AC 24 V, 50/60 Hz Actuator sizing should be done in accordance with the Power Supply 24 VAC (+-) 20% 120V AC (+-) 10%
damper manufacturer’s specs. Control is on-off from an 24 VDC (+-) 10% 50/60Hz
Nominal Voltage AC 19.2 - 28.8 V
Application: auxillary contact, or a manual switch.
Range Power Consumption running : 5W
For the operation of air dampers that perform safety 6W
functions (e.g. frost and smoke protection, hygiene) Power Consumption monitoring 6W Mode of Operation: holding : 2.6W 3.5W
holding 2.5W The NF series actuators provide true spring return Transormer Sizing 2 VA 7VA
Mode of Operation: operation for reliable fail-safe application and positive
For Wire Sizing 10 VA
The AF24-SR actuator moves the damper to its normal close off on air tight dampers. The spring return system Electrical Connection 3 ft, 18 GA appliance cable 1/2” conduit
Protection Class III (safety extra- low voltage) connection.
working position while tensioning the return spring at the provide consistent torque to the damper with and without
same time. If the power supply is interrupted, the energy Degree of Protection IP 54 power applied to the actuator. Overload Protection Electronic throughout 0 to 95˚ rotation.
stored in the spring moves the damper back to its safe Connecting Cable -Motor 1m, 5 x 0.75 mm2 Angle Rotation 95°, adjustable 30 to 95° w/ accessories
position.
Control Signal Y1 DC 0 - 10V @ input resistance 100kΩ (0.1mA) Torque 60 in-lb [7Nm] constant torque
Dimensions
Variable End Switch: Control Signal Y2 0 - 20V phasecut @ input resistance 8kΩ (50mW) Direction of Rotation Spring Return can be selected by L/R Mounting.
The actuator has one fixed auxiliary switch and one Operating Range DC 2 - 10V (at control signal Y1) Position Indication Visual Indicator, -5˚ to 90˚ (0˚ is spring return
adjustable auxiliary switch whic allows angle of rotation of 2 - 10V phasecut (at control signal Y2) position).
5% and between 26 - 89% to be signalled. Measuring Voltage U DC 2 - 10V @ max.0.5mA (for 0..100% Running Time Motor: < 75 sec
angle of rotation). Spring Return < 60 sec
Dimensions (+-) 5%
Synchronisation Humidity 5 to 95% RH noncondensing
Tolerance
Ambient Temperature -22 ˚F to 122 ˚F [-30 ˚C to +50 ˚C]
Direction of Rotation Motor selected with switch L/R spring selected
by L/R Mounting Storage Temperature -40 ˚F to 175 ˚F [-40 ˚C to 80 ˚C]
BELIMO DAMPER ACTUATORS
voltage)
Housing Material Zinc coated steel
-Spring Return min. 15 Nm
Agency Listings UL 873 listed, CSA 4813 02 certified
Angle of Rotation Max. 95˚ (adj. 26…95% < with supplied
limit stop). Noise Level Max. 45 dB (A)
Wiring Diagram Service Life Min. 60000 operations Weight 6.6 lbs (3.0 kg.) 7.3 lbs (3.3 kg)
Maintenance Maintenance-free
238 Right to alterations reserved. SAFID is a registered trademark. © Copyright 2018. All rights reserved Right to alterations reserved. SAFID is a registered trademark. © Copyright 2018. All rights reserved 239
SPRING-RETURN OPEN CLOSE ACTUATOR SPRING-RETURN OPEN CLOSE ACTUATOR
FOR DAMPERS UP TO 1.5M² FOR DAMPERS UP TO 1.5M²
OPEN/CLOSE ACTUATOR [24V, 120C AC] CODE: A14 & 15 CODE: A16 OPEN/CLOSE ACTUATOR [24V]
NF 24-S, NF 120-S US (SPRING-RETURN) NF 24-SR US (SPRING-RETURN)
Application: Technical Data NF 24-S US NF 120-S US Proportional Damper Actuator: 24 V for 0 - 10 VDC or to Technical Data
For on-off, fail-safe control of dampers in HVAC systems. 10 mA control signal. Output signal of 2 to 10 VDC for
Actuator sizing should be done in accordance with the position indicator.
Power Supply 24 VAC (+-) 20% 120VAC (+-) 10% Power Supply 24 VAC (+-) 20%, 50/60Hz
damper manufacturer’sspecs. Control is on-off from an
24 VDC (+-) 10% 50/60Hz 24 VDC (+-) 10%
auxillary contact, or a manual switch. Application:
Power Consumption running: 5 W 6W Power Consumption running : 3W
For on-off, fail-safe control of dampers in HVAC systems.
Mode of Operation: holding: 2.6 W 3.5 W
Actuator sizing should be done in accordance with the holding : 1.W
The NF series actuators provide true spring return damper manufacturer’s specs.
Transormer Sizing 2 VA 7 VA Transormer Sizing 10 VA (class 2 power source)
operation for reliable fail-safe application and positive
close off on air tight dampers. The spring return system Electrical Connection 3 ft, 18 GA appliance cable 1/2” conduit Mode of Operation: Electrical Connection 3 ft, 18 GA appliance cable 1/2” conduit
provide consistent torque to the damper with and without connection. The NF series actuators provide true spring return
connection.
power applied to the actuator. The actuators is provided operation for reliable fail-safe application and positive Overload Protection Electronic throughout 0 to 95˚ rotation.
Overload Protection electronic throughout 0 to 95˚ rotation.
with one built-in auxiliary switch. The SPDT switches are close off on air tight dampers. The spring return system
Angle Rotation 95°, adjustable 30 to 95° w/ accessories Control Signal Y1 0 to 10 VDC, 0 to 20 mA
provided forsafety interfacing or signaling, for example for provide consistent torque to the damper with and without
fan start up. Torque 60 in-lb [7Nm] constant torque
power applied to the actuator. Imput Impedance 100 kW (0.1 mA), 500W
Direction of Rotation Spring Return can be selected by L/R Mounting. Operating Range 2 to 10 VDC, 4 to 20 mA
Dimensions
Position Indication Visual Indicator, -5˚ to 90˚ (0˚ is spring return Feedback output “U” 2 to 10 VDC (max. 0.5 mA) for 95˚
position). Dimensions
Angle Rotation 95°, adjustable 30 to 95° with accessories
Auxiliary Switch 1xSPDT 7A (2.5A) @ 250 VAC, UL listed
Torque 60 in-lb [7Nm] constant torque
NF...-S Adjustable 5˚ to 85˚.
Direction of Rotation Spring Return Selected by L/R Mounting
Running Time Motor: < 75 sec Control Direction Selected by L/R Switch
Spring Return < 60 sec
Position Indication Visual Indicator, -5˚ to 95˚ (0˚ is spring
Humidity 5 to 95% RH noncondensing return position).
BELIMO DAMPER ACTUATORS
240 Right to alterations reserved. SAFID is a registered trademark. © Copyright 2018. All rights reserved Right to alterations reserved. SAFID is a registered trademark. © Copyright 2018. All rights reserved 241
OPEN CLOSE ACTUATOR FOR DAMPERS UP TO 4M² OPEN CLOSE ACTUATOR FOR DAMPERS UP TO 4M²
OPEN/CLOSE ACTUATOR [230V AC, 24V AC/DC] CODE: A17 & 18 CODE: A17.1 & 18.1 OPEN/CLOSE ACTUATOR [230V AC, 24V AC/DC]
SM 230A, SM 24A (OPEN/CLOSE) SM 230A-S, SM 24A-S (OPEN/CLOSE)
Control: Technical Data SM 230A SM 24A Control: Technical Data SM230A -S SM24A-S
Open-Close or 3-point Open-close or 3-point
Power Supply 230 V AC 24 V AC/DC Integrated auxilliary switch Power Supply 230 V AC 24 V AC/DC
Application: 50/60 Hz 50/60 Hz
The actuator is overload-proof, requires no limith switches Application:
and automatically stops when the end stop is reached. Nominal Voltage AC 85 - 265 V AC/DC 19.2 - 28.8 V The actuator is overload-proof, requires no limith switches Nominal Voltage AC 85 - 265 V AC/DC 19.2 - 28.8V
Range Range
and automatically stops when the end stop is reached.
Mode of Operation:
Power Consumption Power Consumption
Manual operation is possible with the selfresetting • In
Mode of Operation:
Operation 2.5 @ nominal torque 2 W @ nominal torque • In Operation 2.5 @ nominal torque 2 W @ nominal torque
pushbutton (the gearing latch remains disengaged as long • At
Manual operation is possible with the self resetting push
Rest 0.6 W • At Rest 0.6 W
as the pushbutton is pressed). • For
button (the gearing latch remains disengaged as long as
wire Sizing 6 VA • For wire Sizing 6 VA
the pushbutton is pressed). Flexible signalization with
Connecting Cable 1 m, 3 x 0.75 mm2 adjustable auxilliary switch (0 - 100%). Auxiliary Switch 1 x SPDT, 1 mA … 3 (0.5) A, AC 250 V
Connection
Torque Min. 20Nm @ nominal voltage
Dimensions • Motor Cable 1 m, 3 x 0.75 mm2
Angle of Rotationt Max. 95° , limited on both sides by means of • Auxiliary Switch Cable 1 m, 3 x 0.75 mm2
adjustable, mechanical end stops
Direction of Rotation Reversible with switch 0 or 1
Running Time 150 s
Torque Min. 20Nm @ nominal voltage
Sound Power Level Max. 45 dB (A)
Angle of Rotationt Max. 95° , limited on both sides by means of
Position Indication Mechanical, pluggable adjustable, mechanical end stops
Protection Class II totally insulated
Running Time 150 s
Protection Class III safety extra-low voltage
Sound Power Level Max. 45 dB (A)
BELIMO DAMPER ACTUATORS
Maintenance Maintenance-free
242 Right to alterations reserved. SAFID is a registered trademark. © Copyright 2018. All rights reserved Right to alterations reserved. SAFID is a registered trademark. © Copyright 2018. All rights reserved 243
MODULAITING ACTUATOR FOR DAMPERS UP TO 4M² OPEN CLOSE ACTUATOR FOR DAMPERS UP TO 1.5M²
MODULATING ACTUATOR [230V AC] CODE: A19 CODE: A20 & 21 OPEN/CLOSE ACTUATOR [230V AC, 24V AC/DC]
SM 230-ASR (MODULATING) NM 230, NM 24 (OPEN/CLOSE)
Control: Technical Data SM 230-ASR NM 230: Control by single-pole contact (single wire Technical Data NM 230 NM 24
DC 0 - 10 V control). NM24: Reversible.
Position Feedback: DC 2 - 10 V6. Power Supply AC 100 - 230 V, 50/60 Hz Power Supply 230 V AC 24 V AC/DC
Application: 50/60 Hz
Application: Nominal Voltage AC 85 - 265 V The damper actuator has no limit switches and is overload-
Range Nominal Voltage AC 198 - 264 V AC/DC 19.2 - 28.8 V
The actuator is overload-proof, requires no limith switches proof. It stops automatically when it reaches the damper
Range
and automatically stops when the end stop is reached. Power Consumption or actuator end stop.
• In Operation 3.5 @ nominal torque For Wire Sizing 18 VA 3.5 VA
Mode of Operation: • At Rest 1W Mode of Operation:
Power Consumption 2W 2W
The actuator is controlled by means of a standard control • For wire Sizing 6.5 VA A functional check of damper operation is simplicity itself:
signal DC 0 - 10 V. It opens to the position dictated by the gearing can be disengaged by simply pressing a push Torque 1m long, 3 x 0.75mm2
Connection Cable 1 m, 2 x 0.75 mm2
this signal. The measuring voltage U allows the damper button on top of th case. While the pushbutton remains Direction of Rotation selected with L/R switch
• Motor Cable 1 m, 4 x 0.75 mm2
position (0 - 100%) to be electrically indicated and serves depressed, the damper can be operated by hand. Torque Min. 8Nm (at rated voltage)
• Auxiliary Switch
as a follow-up control signal forother actuators. Manual
Angle of Rotationt Max 95˚ (adjustable by mechanical stops)
operation is possible with the self-resetting push button Control Signal Y DC 0 - 10 V, typical input impedance 100 kΩ
(the gearing latch remains disengaged as long as the
DC 2 - 10 V
Dimensions Running Time 75 - 150s (0 - 8Nm)
Working Rang
pushbutton is pressed). Sound Power Level Max. 35 dB (A)
Positioning Accuracy DC 2 - 10 V
(at Y=0 V) Protection Class II (all insulated) III (safety low voltage)
Torque Min. 20Nm @ nominal voltage Degree of Protection IP 54 (cable entry down)
Angle of Rotationt Max. 95° , limited on both sides by means of Ambient temp. Range -20 to +50 ˚C
adjustable, mechanical end stops
Non-Operating temp. -40 to +80 ˚C
Running Time 150 s
BELIMO DAMPER ACTUATORS
Ambient Humidity
Sound Power Level Max. 45 dB (A) EMC CE According to 89/336/EEC & 92/31/EEC
Maintenance Maintenance-free
244 Right to alterations reserved. SAFID is a registered trademark. © Copyright 2018. All rights reserved Right to alterations reserved. SAFID is a registered trademark. © Copyright 2018. All rights reserved 245
MODULAITING ACTUATOR FOR DAMPERS UP TO 1.5M² OPEN CLOSE ACTUATOR FOR DAMPERS UP TO 6M²
MODULATING ACTUATOR [AC 24V] CODE: A22 CODE: A23 OPEN/CLOSE ACTUATOR [230 V AC]
NM 24-SR (MODULATING) GM 240 (OPEN/CLOSE)
Weight 2000 g
Sound Power Level Max. 35 dB (A)
Maintenance Maintenance-free
Weight 900 g
246 Right to alterations reserved. SAFID is a registered trademark. © Copyright 2018. All rights reserved Right to alterations reserved. SAFID is a registered trademark. © Copyright 2018. All rights reserved 247
OPEN CLOSE ACTUATOR FOR DAMPERS UP TO 6M² MODULAITING ACTUATOR FOR DAMPERS UP TO 6M²
OPEN/CLOSE ACTUATOR [AC/DC 24V] CODE: A24 CODE: A25 MODULATING ACTUATOR [AC 24V]
GM 24 (OPEN/CLOSE) GM 24-SR (MODULATING)
Reversible Technical Data Control DC 0...10 V or 0...20 V phasecut Position Technical Data
feedback DC 2...10 V
Application: Power Supply AC 24 V, 50/60 Hz, DC 24 V Power Supply AC 24 V AC 50/60 Hz
The damper actuator has no limit switches and is Application:
Nominal Voltage AC 19.2 - 28.8 V, DC 21.6 - 26.4 V Nominal Voltage AC/DC 19.2 - 28.8 V
overload-proof. It stops automatically when it reaches the The damper actuator has no limit switches and is
Range Range
damper or actuator end stop. overload-proof. It stops automatically when it reaches the
For Wire Sizing 6 VA damper or actuator end stop. For Wire Sizing 7 VA
Mode of Operation: Power Consumption 3 W running, 1 W at the end position Power Consumption 3 W running, 2 W at rest
A functional check of damper operation is simplicity itself: Mode of Operation:
Connecting Cable 0.9m long, 3x0.75 mm2
the gearing can be disengaged by simply pressing a push A functional check of damper operation is simplicity Connecting Cable 0.9m long, 5 x 0.75 mm2
Direction of Rotation Reversible with switch A/B
button on top of the case. While the pushbutton remains itself: the gearing can be disengaged by simply pressing Control Signal Y1 DC 0 - 10 V input resistance 100kΩ (0.1mA)
depressed, the damper can be operated by hand. Torque Min. 30Nm (at rated voltage) a pushbutton on top of the case. While the pushbutton
remains depressed, the damper can be operated by hand. Control Signal Y2 0 - 20 V phasecut @ input resistance 8 k (50 mW)
Angle of Rotationt Mechanically limited to 95˚
Maintenance Maintenance-free
Weight 2000 g
248 Right to alterations reserved. SAFID is a registered trademark. © Copyright 2018. All rights reserved Right to alterations reserved. SAFID is a registered trademark. © Copyright 2018. All rights reserved 249