Professional Documents
Culture Documents
&ROG6KULQN6LOLFRQH5XEEHU
75-66HULHV&&DELQHW7HUPLQDWLRQ
,QVWUXFWLRQV
Kit Contents:
²6LOLFRQH5XEEHU3KDVH5HMDFNHWLQJ
6OHHYH$VVHPEO\
²&ROG6KULQN6LOLFRQH5XEEHU
7HUPLQDWLRQ$VVHPEO\
²5ROO7LQQHG&RSSHU*URXQG%UDLG
²&RQVWDQW)RUFH6SULQJ
²5ROO9LQ\O7DSH
²&DEOH3UHSDUDWLRQ.LW
²,QVWDOODWLRQ,QVWUXFWLRQV
Kit Number BIL Cable Insulation 3.3 kV 3.3 kV 5.0 kV 6.6 kV 6.6 kV 8.7 kV 10 kV 15 kV 15 kV 20 kV 25/28 kV
(kV) Range [inch (mm)] (mm 2) (mm 2) (AWG) (mm 2) (mm 2) (AWG) (mm 2) (mm 2) (AWG) (mm 2) (AWG)
IEC JIS AEIC JIS IEC AEIC IEC IEC AEIC IEC AEIC
7621-T110-3RJS 110 0.50–0.70 (12.7–17.8) 50–95 38–60 1–3/0 14–38 35–70 2–2/0 10–50 16–25 2–1 — —
7622-T110-3RJS 110 0.70–0.92 (17.8–23.4) 120–185 100–150 4/0–400 60–100 95–150 3/0–350 70–150 35–95 1/0–4/0 — —
7624-T110-3RJS 110 0.92–1.18 (23.4–30.0) 240–300 200–250 500–750 150–250 185–300 400–600 185–300 120–185 250–450 — —
7625-T110-3RJS 110 1.18–1.52 (30.0–38.6) — 300–325 800–1000 300–325 — 750–1000 — 200–325 500–750 — —
7622-T125-3RJS 125 0.70–0.92 (17.8–23.4) 120–185 100–150 4/0–400 60–100 95–150 3/0–350 70–150 35–95 1/0–4/0 25–70 —
7624-T125-3RJS 125 0.92–1.18 (23.4–30.0) 240–300 200–250 500–750 150–250 185–300 400–600 185–300 120–185 250–450 95–185 —
7625-T125-3RJS 125 1.18–1.52 (30.0–38.6) — 300–325 800–1000 300–325 — 750–1000 — 200–325 500–750 240–300 —
7693-T150-3RJS 150 0.70–0.92 (17.8–23.4) 120–185 100–150 4/0–400 60–100 95–150 3/0–350 70–150 35–95 1/0–4/0 25–70 2–1/0
7694-T150-3RJS 150 0.92–1.18 (23.4–30.0) 240–300 200–250 500–750 150–250 185–300 400–600 185–300 120–185 250–450 95–185 2/0–250
7695-T150-3RJS 150 1.18–1.52 (30.0–38.6) — 300–325 800–1000 300–325 — 750–1000 — 200–325 500–750 240–300 300–500
0™ &ROG6KULQN
3/C Copper Tape Shield Cable 6LOLFRQH5XEEHU
&DELQHW0RXQW7HUPLQDWLRQ
IRU&&RSSHU7DSH6KLHOG&DEOHV
ZLWKRUZLWKRXW*URXQG:LUHV
Note: Individual phase length and separation dimensions vary according to specific installation and equipment
design requirements. They must, therefore, be determined by the installer and must conform to accepted
engineering practices.
6WULSEDFNFDEOHMDFNHWDQGDUPRUDFFRUGLQJWRHTXLSPHQWHQWUDQFHEXVKLQJDQGFDELQHWFRQILJXUDWLRQUHTXLUHPHQWV
5HPRYHEHGGLQJ LQQHUVKHDWK LISUHVHQWDQGDQ\UHPDLQLQJFRUHILOOHUV 6HFXUHHDFKFRSSHUWDSHVKLHOGHQGZLWKD
WHPSRUDU\EDQGRIYLQ\OWDSH ① )LJXUH
Figure 1
$
,,,,,
zzzzz
yyyyy
2.0 Attach Metallic Shield Grounding Braids.
&XWVXSSOLHGWLQQHGFRSSHUJURXQGLQJEUDLGLQWRWKUHHHTXDO PP OHQJWKV ([SDQGHDFKEUDLGHQGIRUD
GLVWDQFHRI PP ② )LJXUH
Figure 2
|||||
$WWDFKVKLHOGJURXQGEUDLGV
$ 3RVLWLRQHDFKH[SDQGHGJURXQGEUDLGHQGRYHUSKDVHVKLHOGLQJDVVKRZQLQ)LJXUH
% 8VLQJYLQ\OWDSHEDQGVVHFXUHXSSHUEUDLGHQGWRFRSSHUWDSHVKLHOGLQJ PP EH\RQGFDEOHEUHDNRXWSRLQW
yy
zz,,
& &RQQHFWH[SDQGHGJURXQGEUDLGHQGVWRFRSSHUWDSHVKLHOGVXVLQJVXSSOLHGFRQVWDQWIRUFHVSULQJV )ROORZLQJ
DSSOLFDWLRQFLQFK WZLVWZLWKKDQG HDFKVSULQJWRWLJKWHQ
Figure 3
zz
||,,y
y
,,,
zz
yyy
||
$SSO\WZRKDOIODSSHGOD\HUVYLQ\OWDSHRYHUFRQVWDQWIRUFHVSULQJVDQGJURXQGVWUDSHQGV ➂ )LJXUH
Figure 4
||
$
3.0 Install Silicone Rubber Re-jacketing Sleeves.
)URPWKHFKDUWEHORZGHWHUPLQHWKHFRUUHFW>$@GLPHQVLRQIRUWKH47,,,SURGXFWEHLQJLQVWDOOHG
7620-T95-3RJS
7621-T110-3RJS
7621-T95-3RJS 7622-T125-3RJS 7693-T150-3RJS
7622-T110-3RJS
7623-T95-3RJS 7624-T125-3RJS 7694-T150-3RJS
7624-T110-3RJS
7624-T95-3RJS 7625-T125-3RJS 7695-T150-3RJS
7625-T110-3RJS
7625-T95-3RJS
6.25" (159 mm) 8.5" (216 mm) 7.0" (178 mm) 12.0" (305 mm)
zz
,,,
yyy
Note: [X] = [A] (From chart above) + [B] (Lug barrel depth). Allow for crimp growth when using aluminum lugs.
Figure 5
,,,
yyy
zz
||
'HWHUPLQHUHTXLUHGSKDVHUHMDFNHWLQJVOHHYHOHQJWK >6@)LJXUH
8VLQJVFLVVRUVWULPUHMDFNHWLQJVOHHYHDVVHPEO\WROHQJWKUHTXLUHG )LJXUH &XWWXELQJDQGLQQHUEUDLGWRJHWKHU
Note: Inner polyester braid should extend approximately 75 mm (3.0") beyond re-jacketing tube end before
cutting. There is no need for termination-end braid exposure.
Figure 6
$
*XLGHRQHUHMDFNHWLQJVOHHYHDVVHPEO\RYHUHDFKFDEOHSKDVHOHJ )LJXUH
Push sleeve assembly from above. Continuously guide the free end maintaining sleeve-to-cable-core alignment.
Figure 7
Note: Do not damage silicone tubing while cutting. Sleeve assembly may be rotated to ease trimming. When
||
zz,,y
y
doing so, rotate in the direction of the cable copper tape shield wrap.
Figure 8
||
6OLGHUHMDFNHWLQJVOHHYHDVVHPEO\LQWRGHVLUHGILQDOSRVLWLRQ 3XOOIROGHGVOHHYHVHFWLRQGRZQRQWRFDEOH
SKDVHVKLHOGLQJ
Note: Re-jacketing sleeve upper end should now align with upper edge of previously-installed marker tape
zz
||,,y
y
(② Figure 9). Minor tube adjustments can be made as needed.
Figure 9
$
||
4.0 Install QT-III Cold Shrink Termination Assemblies.
3UHSDUHFDEOHSKDVHOHJVDFFRUGLQJWRGLPHQVLRQVVKRZQ )LJXUH
Figure 10
7620-T95-3RJS
7621-T110-3RJS
7621-T95-3RJS 7622-T125-3RJS 7693-T150-3RJS
7622-T110-3RJS
7623-T95-3RJS 7624-T125-3RJS 7694-T150-3RJS
7624-T110-3RJS
7624-T95-3RJS 7625-T125-3RJS 7695-T150-3RJS
7625-T110-3RJS
7625-T95-3RJS
A 6.25" (159 mm) 8.5" (215 mm) 7.0" (179 mm) 12.0" (305 mm)
B Lug Depth* Lug Depth* Lug Depth* Lug Depth*
C 1.5" (38.1 mm) 2.5" (64 mm) 1.5" (38.1 mm) 2.5" (64 mm)
D 0.75" (19.1 mm) 1.25" (32 mm) 0.75" (19.1 mm) 1.25" (32 mm)
*Allow for crimp growth when using aluminum lugs and connectors.
Figure 11
$
3ODFHDWHUPLQDWLRQLQVWDOODWLRQPDUNHUWDSHDWSRVLWLRQ>0@ )LJXUH
Figure 12
7620-T95-3RJS
7621-T110-3RJS
7621-T95-3RJS 7622-T125-3RJS 7693-T150-3RJS
7622-T110-3RJS
7623-T95-3RJS 7624-T125-3RJS 7694-T150-3RJS
7624-T110-3RJS
7624-T95-3RJS 7625-T125-3RJS 7695-T150-3RJS
7625-T110-3RJS
7625-T95-3RJS
M 4.0" (102 mm) 5.0" (127 mm) 4.0" (102 mm) 5.0" (127 mm)
,QVWDOOWHUPLQDOOXJV
Note: Special Case—When lug spade dimension is larger than inside diameter of white plastic termination
core, position termination assemblies over cable phase legs prior to installing lugs. Remove inner red
shipping core from each termination assembly by pulling and unwinding the loose red core ribbon. Position
one termination over each cable phase leg. Each termination assembly must be positioned with its loose
white core ribbon end directed toward the open (cut) end of the cable. Continue with lug installations.
$ )RU$OXPLQXP&RQGXFWRUV²7KRURXJKO\ZLUHEUXVKFRQGXFWRUVWUDQGVWRUHPRYHDOXPLQXPR[LGHOD\HU
,PPHGLDWHO\LQVHUWFRQGXFWRULQWRWHUPLQDOOXJEDUUHODVIDUDVLWZLOOJR
% (QVXUHWKDWHDFKOXJIDFHLVSDUDOOHOWRHTXLSPHQWEXVKLQJRUOXJFRQQHFWLRQLQWHUIDFH ➂ )LJXUH
Figure 13
$
,QVWDOO47,,,7HUPLQDWLRQDVVHPEOLHV
$ 5HPRYHWKHLQQHUUHGVKLSSLQJFRUHIURPWKHWHUPLQDWLRQDVVHPEO\E\SXOOLQJDQGXQZLQGLQJWKHORRVHUHGFRUHHQG
% 3RVLWLRQWKHWHUPLQDWLRQDVVHPEO\ZLWKWKHORRVHZKLWHFRUHULEERQGLUHFWHGWRZDUGWKHWHUPLQDOOXJ
➄ )LJXUH
& $OLJQWKHEDVHRIWKHWHUPLQDWLRQ QRWWKHSODVWLFFRUH ZLWKWKHLQVWDOODWLRQPDUNHUWDSHDVVKRZQ
' *UDVSWKHORRVHZKLWHFRUHULEERQ 3XOODQGXQZLQGFRXQWHUFORFNZLVHDURXQGFDEOHSKDVHHQG ➅ )LJXUH
Note: After the silicone rubber termination makes adequate contact (approximately 1.0" or 25 mm), release the
assembly and continue unwinding the core. Do not pull or push on the assembly while unwinding.
( 5HPRYHWKHLQVWDOODWLRQPDUNHUWDSH
&RQQHFWFDEOHJURXQGZLUHVDQGVKLHOGJURXQGLQJEUDLGVWRV\VWHPJURXQG HDUWK DFFRUGLQJWRQRUPDOSUDFWLFH
Figure 14
IMPORTANT NOTICE
All statements, technical information and recommendations related to the Seller’s products are based on information believed to be reliable,
but the accuracy or completeness thereof is not guaranteed. Before utilizing the product, the user should determine the suitability of the
product for its intended use. The user assumes all risks and liability whatsoever in connection with such use.
Any statements or recommendations of the Seller which are not contained in the Seller’s current publications shall have no force or effect
unless contained in an agreement signed by an authorized office of the Seller. The statements contained herein are made in lieu of all
warranties, expressed or implied, including but not limited to the implied warranties of merchantability and fitness for a particular purpose
which warranties are hereby expressly disclaimed.
SELLER SHALL NOT BE LIABLE TO THE USER OR ANY OTHER PERSON UNDER ANY LEGAL THEORY, INCLUDING BUT NOT
LIMITED TO NEGLIGENCE OR STRICT LIABILITY, FOR ANY INJURY OR FOR ANY DIRECT, INDIRECT, INCIDENTAL OR
CONSEQUENTIAL DAMAGES SUSTAINED OR INCURRED BY REASON OF THE USE OF ANY OF THE SELLER’S PRODUCTS.