Professional Documents
Culture Documents
BODIES
Deformation
Whenever a force is applied to a body, it will tend to change the
Engr. Marvin Bartido 1ST TERM AY 2023-2024
2
I can do all things through Christ who gives me strength.
Philippians 4:13
Strain
In general terms, strain is a geometric quantity that measures
Engr. Marvin Bartido 1ST TERM AY 2023-2024
3
I can do all things through Christ who gives me strength.
Philippians 4:13
Note that normal strain, being change in length per unit length,
is a dimensionless quantity. However “units” such as in./in. or
mm/mm are frequently used for normal strain.
4
I can do all things through Christ who gives me strength.
Philippians 4:13
Shear Strain
Engr. Marvin Bartido 1ST TERM AY 2023-2024
The lengths of the sides of the element do not change, but the
element undergoes a distortion from a rectangle to a parallelogram.
The shear strain, which measures the amount of distortion is
the angle 𝛾, always expressed in radians.
𝜋
𝛾= − 𝜃′
2
5
I can do all things through Christ who gives me strength.
Philippians 4:13
6
SAMPLE PROBLEMS
1. When force P is applied to the rigid lever arm ABC in Fig. 2–5a, the
arm rotates counterclockwise about pin A through an angle of 0.05°.
Determine the normal strain developed in wire BD.
Engr. Marvin Bartido 1ST TERM AY 2023-2024
Find: 400 𝑚𝑚
tan 𝛼 =
300 𝑚𝑚
normal strain developed in wire 400
BD 𝛼= tan−1
300
𝛼 = 53.13010°
Solution 1:
The orientation of the lever arm Then
after it rotates about point A is 90° + 0.05° = 𝛼 + 𝜑
shown in Fig. 2–5b. From the
geometry of this figure, 𝜑 = 90° + 0.05° − 𝛼
𝜑 = 90° + 0.05° − 53.13010°
𝜑 = 36.9199°
7
SAMPLE PROBLEMS
Normal Strain:
𝐿𝐵′ 𝐷 −𝐿𝐵𝐷
𝜖𝐵𝐷 =
𝐿𝐵𝐷
300.34908−300
𝜖𝐵𝐷 =
300
𝜖𝐵𝐷 = 0.0011636 𝑚𝑚/𝑚𝑚
tan 𝜃 = 𝜃
∆𝐿𝐵𝐷
𝜃=
400 𝑚𝑚
∆𝐿𝐵𝐷 =
𝜋
(0.05°) 400 𝑚𝑚
180°
∆𝐿𝐵𝐷 = 0.34907 𝑚𝑚
Therefore,
∆𝐿𝐵𝐷
𝜖𝐵𝐷 =
𝐿𝐵𝐷
0.34907
𝜖𝐵𝐷 =
300
𝜖𝐵𝐷 = 0.0011636 𝑚𝑚/𝑚𝑚
8
SAMPLE PROBLEMS
2. Due to a loading, the plate is deformed into the dashed shape shown
in Fig. 2–6a. Determine (a) the average normal strain along the side AB,
and (b) the average shear strain in the plate at A relative to the x and y
axes.
Engr. Marvin Bartido 1ST TERM AY 2023-2024
Find:
(a) the average normal strain along the side
AB, and
(b) the average shear strain in the plate at A Part (b). As noted in Fig. 2–6c, the once 90°
relative to the x and y axes. angle BAC between the sides of the plate at
Solution: A changes to 𝜃′ due to the displacement of
𝜋
B to B’. Since 𝛾𝑥𝑦 = 2 − 𝜃′, then 𝛾𝑥𝑦 is the
angle shown in the figure. Thus,
9
I can do all things through Christ who gives me strength.
Philippians 4:13
10
I can do all things through Christ who gives me strength.
Philippians 4:13
Tension Test
Engr. Marvin Bartido 1ST TERM AY 2023-2024
11
I can do all things through Christ who gives me strength.
Philippians 4:13
Stress-Strain Diagram
Engr. Marvin Bartido 1ST TERM AY 2023-2024
12
For God so loved the world that He gave His one and only Son,
that whoever believes in Him shall not perish but have eternal life.
John 3:16
• Elastic Behavior
Elastic behavior of the material occurs when the strains in the
specimen are within the light orange region shown in Fig. 3–4. Here the
curve is actually a straight line throughout most of this region, so that the
stress is proportional to the strain. The material in this region is said to be
linear elastic. The upper stress limit to this linear relationship is called the
Engr. Marvin Bartido 1ST TERM AY 2023-2024
proportional limit, 𝜎𝑝𝑙 . If the stress slightly exceeds the proportional limit,
the curve tends to bend and flatten out as shown. This continues until the
stress reaches the elastic limit. Upon reaching this point, if the load is
removed the specimen will still return back to its original shape. Normally for
steel, however, the elastic limit is seldom determined, since it is very close to
the proportional limit and therefore rather difficult to detect.
• Yielding
A slight increase in stress above the elastic limit will result in a
breakdown of the material and cause it to deform permanently. This
behavior is called yielding, and it is indicated by the rectangular dark orange
region of the curve. The stress that causes yielding is called the yield stress
or yield point or yield strength, 𝝈𝒀 , and the deformation that occurs is called
plastic deformation. Although not shown in Fig. 3–4, for low-carbon steels or
those that are hot rolled, the yield point is often distinguished by two values.
The upper yield point occurs first, followed by a sudden decrease in load-
carrying capacity to a lower yield point. Notice that once the yield point is
reached, then as shown in Fig. 3–4, the specimen will continue to elongate
(strain) without any increase in load. When the material is in this state, it is
often referred to as being perfectly plastic.
• Strain Hardening
When yielding has ended, an increase in load can be supported by the
specimen, resulting in a curve that rises continuously but becomes flatter
until it reaches a maximum stress referred to as the ultimate stress or
ultimate strength, 𝜎𝑢 . The rise in the curve in this manner is called strain
hardening, and it is identified in Fig. 3–4 as the region in light green.
The ultimate strength is commonly used as the maximum stress that
the material can carry.
13
For God so loved the world that He gave His one and only Son,
that whoever believes in Him shall not perish but have eternal life.
John 3:16
• Necking
Up to the ultimate stress, as the specimen elongates, its cross-
sectional area will decrease. This decrease is fairly uniform over the
specimen’s entire gauge length; however, just after, at the ultimate
stress, the cross-sectional area will begin to decrease in a localized
Engr. Marvin Bartido 1ST TERM AY 2023-2024
14
I can do all things through Christ who gives me strength.
Philippians 4:13
the maximum safe axial stress used in design. In most designs, the
working stress should be limited to values not exceeding the
proportional limit so that the stresses remain in the elastic range (the
straight-line portion of the stress-strain diagram). However, because
the proportional limit is difficult to determine accurately, it is
customary to base the working stress on either the yield stress, 𝜎𝑌 ,or
the ultimate stress, 𝜎𝑢 , divided by a suitable number F.S., called the
factor of safety. Thus,
𝜎𝑌 𝜎𝑢
𝜎𝑎𝑙𝑙𝑜𝑤 = or 𝜎𝑎𝑙𝑙𝑜𝑤 =
𝐹.𝑆. 𝐹.𝑆.
15
SAMPLE PROBLEMS
16
I can do all things through Christ who gives me strength.
Philippians 4:13
As seen in Fig. 3–6, since 𝜖𝑓 = 0.380 𝑖𝑛./𝑖𝑛., this value would be 38%
for a mild steel specimen.
Besides steel, other metals such as brass, molybdenum, and zinc may
also exhibit ductile stress–strain characteristics similar to steel, whereby they
undergo elastic stress–strain behavior, yielding at constant stress, strain
hardening, and finally necking until fracture.
17
For God so loved the world that He gave His one and only Son,
that whoever believes in Him shall not perish but have eternal life.
John 3:16
Normally a 0.2% strain (0.002 in./in.) is chosen, and from this point on
the 𝜖 axis, a line parallel to the initial straight-line portion of the
stress–strain diagram is drawn. The point where this line intersects the
curve defines the yield strength. An example of the construction for
determining the yield strength for an aluminum alloy is shown in Fig.
3–7. From the graph, the yield strength is 𝜎𝑌 = 51 𝑘𝑠𝑖 (352 MPa).
18
For God so loved the world that He gave His one and only Son,
that whoever believes in Him shall not perish but have eternal life.
John 3:16
• Brittle Materials
Materials that exhibit little or no yielding before failure are
referred to as brittle materials.
Gray cast iron is an example, having a stress–strain diagram in
tension as shown by portion AB of the curve in Fig. 3–9. Here fracture
Engr. Marvin Bartido 1ST TERM AY 2023-2024
19
For God so loved the world that He gave His one and only Son,
that whoever believes in Him shall not perish but have eternal life.
John 3:16
20
I can do all things through Christ who gives me strength.
Philippians 4:13
Hooke’s Law
As noted in the previous section, the stress–strain diagrams for most
Engr. Marvin Bartido 1ST TERM AY 2023-2024
21
I can do all things through Christ who gives me strength.
Philippians 4:13
Strain Hardening
If a specimen of ductile material, such
Engr. Marvin Bartido 1ST TERM AY 2023-2024
22
I can do all things through Christ who gives me strength.
Philippians 4:13
Strain Energy
As a material is deformed by an external load, the load will do external work,
Engr. Marvin Bartido 1ST TERM AY 2023-2024
If the material behavior is linear elastic, then Hooke’s law applies, 𝜎 = 𝐸𝜖 and
therefore we can express the elastic strain-energy density as
1 𝜎2
𝑢=
2𝐸
Modulus of Resilience
In particular, when the stress 𝜎 reaches the proportional limit, the strain-energy density
is referred to as the modulus of resilience, i.e.,
1 1 𝜎𝑝𝑙 2
𝑢𝑟 = 𝜎𝑝𝑙 𝜖𝑝𝑙 =
2 2 𝐸
From the elastic region of the stress–strain diagram, Fig. 3–16a, notice that 𝑢𝑟 is
equivalent to the shaded triangular area under the diagram. Physically a material’s
resilience represents the ability of the material to absorb energy without any
permanent damage to the material.
23
For God so loved the world that He gave His one and only Son,
that whoever believes in Him shall not perish but have eternal life.
John 3:16
Modulus of Toughness
Another important property of a material is the modulus of
toughness, 𝑢𝑡 . This quantity represents the entire area under the
stress–strain diagram, Fig. 3–16b, and therefore it indicates the strain-
energy density of the material just before it fractures.
Engr. Marvin Bartido 1ST TERM AY 2023-2024
24
SUMMARY
25
SUMMARY
26
SAMPLE PROBLEMS
Yield Strength:
For a 0.2% offset, we begin at a strain of
0.2% or 0.0020 in./in. and graphically
extend a (dashed) line parallel to OA
until it intersects the 𝜎 − 𝜖 curve at A’.
The yield strength is approximately:
𝜎𝑌 = 68 𝑘𝑠𝑖
27
For God so loved the world that He gave His one and only Son,
that whoever believes in Him shall not perish but have eternal life.
John 3:16
Axial Deformation
Figure 2.7 shows a bar of length L and constant cross-sectional area A that is
loaded by an axial tensile force P. We assume that the stress caused by P is below the
proportional limit, so the Hooke’s law 𝜎 = 𝐸𝜖 is applicable. Because the bar deforms
𝛿 𝑃
Engr. Marvin Bartido 1ST TERM AY 2023-2024
uniformly, the axial strain is 𝜖 = and the axial stress is 𝜎 = , which upon substitution
𝐿 𝐴
𝑃 𝛿
into Hooke’s law yields = 𝐸 . Therefore, the elongation of the bar is:
𝐴 𝐿
𝑷𝑳
𝜹=
𝑨𝑬
28
SAMPLE PROBLEMS
1. The steel propeller shaft ABCD carries the axial loads shown in the
figure. Determine the change in the length of the shaft caused by these
loads. Use 𝐸 = 29 𝑥 106 𝑝𝑠𝑖 for steal.
Engr. Marvin Bartido 1ST TERM AY 2023-2024
Find:
Change in the length of the shaft
(total axial deformation)
Solution: σ 𝐹𝐻 = 0 → +
For rods with various cross- 𝑃𝐶𝐷 − 4000 = 0
sectional area and internal axial 𝑃𝐶𝐷 = 4000 𝑙𝑏
force, the total elongation is:
𝑃𝐿
𝛿=σ
𝐴𝐸 Summing up all deformation:
(positive for elongation, negative
Solve for the internal forces in for compression)
each bar first, 𝑃𝐿
𝛿=σ
𝐴𝐸
𝛿
𝑃𝐿 𝑃𝐿 𝑃𝐿
= + −
𝐴𝐸 𝐴𝐵 𝐴𝐸 𝐵𝐶 𝐴𝐸 𝐶𝐷
σ 𝐹𝐻 = 0 → + 2000 𝑙𝑏 (60 𝑖𝑛)
𝛿=𝜋 +
𝑃𝐴𝐵 − 2000 = 0 0.5 𝑖𝑛 2 (29 𝑥 106 𝑙𝑏ൗ𝑖𝑛2 )
4
2000 𝑙𝑏 (48 𝑖𝑛)
𝑃𝐴𝐵 = 2000 𝑙𝑏 𝜋 −
0.75 𝑖𝑛 2 (29 𝑥 106 𝑙𝑏ൗ𝑖𝑛2 )
4
4000 𝑙𝑏 (48 𝑖𝑛)
𝜋
0.75 𝑖𝑛 2 (29 𝑥 106 𝑙𝑏ൗ𝑖𝑛2 )
4
𝛿 = 0.013581 𝑖𝑛. (elongation)
σ 𝐹𝐻 = 0 → +
𝑃𝐵𝐶 − 2000 = 0
𝑃𝐵𝐶 = 2000 𝑙𝑏
29
SAMPLE PROBLEMS
2. Rigid beam AB rests on the two short posts shown in the figure. AC is
made of steel and has a diameter of 20 mm, and BD is made of
aluminum and has a diameter of 40 mm. Determine the displacement
of point F on AB if a vertical load of 90 kN is applied over this point.
Take 𝐸𝑠𝑡 = 200 𝐺𝑃𝑎, 𝐸𝑎𝑙 = 70 𝐺𝑃𝑎.
Engr. Marvin Bartido 1ST TERM AY 2023-2024
Find:
Displacement of point F Displacement. The displacement
of the top of each post is
Solution:
Post AC:
Internal Force. The compressive
forces acting at the top of each post 𝑃𝐴𝐶 𝐿𝐴𝐶
are determined from the equilibrium 𝛿𝐴 =
𝐴𝐴𝐶 𝐸𝑠𝑡
of member AB, Fig. 4–8b. These
forces are equal to the internal forces −60000 𝑁 (300 𝑚𝑚)
in each post, Fig. 4–8c. 𝛿𝐴 = 𝜋
20 𝑚𝑚 2 (200000 𝑁ൗ𝑚𝑚2 )
4
𝛿𝐴 = −0.28648 𝑚𝑚
σ 𝑀𝐴 = 0 ↻ +
−𝑃𝐵𝐷 600 + 90 200 = 0 𝛿𝐴 = 0.28648 𝑚𝑚 ↓
𝑃𝐵𝐷 = 30 𝑘𝑁
Post BD:
σ 𝐹𝑉 = 0 ↑ +
𝑃𝐵𝐷 𝐿𝐵𝐷
𝑃𝐴𝐶 + 𝑃𝐵𝐷 − 90 = 0 𝛿𝐵 =
𝐴𝐵𝐷 𝐸𝑎𝑙
𝑃𝐴𝐶 = 60 𝑘𝑁 −30000 𝑁 (300 𝑚𝑚)
𝛿𝐵 = 𝜋
40 𝑚𝑚 2 (70000 𝑁ൗ𝑚𝑚2 )
4
𝛿𝐵 = −0.10231 𝑚𝑚
𝛿𝐵 = 0.10231 𝑚𝑚 ↓
30
SAMPLE PROBLEMS
𝛿𝐹 −0.10231 0.28648−0.10231
=
400 600
𝛿𝐹 = 0.10231 +
400
0.18417
600
𝛿𝐹 = 0.22509 𝑚𝑚 ↓
31
SAMPLE PROBLEMS
Find: 𝑥
𝐴(𝑥) = 800 + 2400 − 800 10000
Elongation of the bar 𝐴 𝑥 = 800 + 0.16𝑥
Solution: 𝛿 10000
= 100000 𝑁
0 𝑑𝑥
In the case of members with varying 800+0.16𝑥 𝑚𝑚2 (200000 𝑁ൗ𝑚𝑚2 )
cross-section: 𝛿=
10000
0.5 0
𝑑𝑥
𝐿
𝑃 10000
800+0.16𝑥
𝑑𝑥
𝛿=න 𝑑𝑥 𝛿= 0.5 0
0 𝐴 𝑥 𝐸 1
800+0.16𝑥
10000
𝛿= 0.5 0.16 ln 800 + 0.16𝑥 ቃ
0
1
𝛿= 0.5 0.16 ln(800 +
1
0.16(10000)) − 0.5 0.16
ln(800 +
0.16(0))
𝛿 = 3.43316 𝑚𝑚
𝐴 = 𝐴(𝑥)
By proportion:
𝐴−𝐴𝐴 𝐴𝐵 −𝐴𝐴
2 2
=
𝑥 𝐿
𝐴−𝐴𝐴 𝐴𝐵 −𝐴𝐴
=
2𝑥 2𝐿
𝐴𝐵 −𝐴𝐴 (2𝑥)
𝐴 − 𝐴𝐴 =
2𝐿
𝑥
𝐴 = 𝐴𝐴 + 𝐴𝐵 − 𝐴𝐴
𝐿
𝐴𝐴 = 40 20 = 800 𝑚𝑚2
𝐴𝐵 = 120 20 = 2400 𝑚𝑚2
𝐿 = 10000 𝑚𝑚
32
For God so loved the world that He gave His one and only Son,
that whoever believes in Him shall not perish but have eternal life.
John 3:16
Poisson’s Ratio
When a deformable body is subjected to an axial tensile force, not only does it
elongate but it also contracts laterally. For example, if a rubber band is stretched, it can
be noted that both the thickness and width of the band are decreased. Likewise, a
compressive force acting on a body causes it to contract in the direction of the force
Engr. Marvin Bartido 1ST TERM AY 2023-2024
In the early 1800s, the French scientist S. D. Poisson realized that within the
elastic range the ratio of these strains is a constant, since the deformations 𝛿 and 𝛿′ are
proportional. This constant is referred to as Poisson’s ratio, 𝑣 (nu), and it has a
numerical value that is unique for a particular material that is both homogeneous and
isotropic. Stated mathematically it is
𝝐𝒍𝒂𝒕
𝒗=−
𝝐𝒍𝒐𝒏𝒈
The negative sign is included here since longitudinal elongation (positive strain)
causes lateral contraction (negative strain), and vice versa. Notice that these strains are
caused only by the axial or longitudinal force P; i.e., no force or stress acts in a lateral
direction in order to strain the material in this direction.
Poisson’s ratio is a dimensionless quantity, and for most nonporous solids it has
a value that is generally between ¼ and 1/3. For an “ideal material” having no lateral
deformation when it is stretched or compressed Poisson’s ratio will be 0. Furthermore,
the maximum possible value for Poisson’s ratio is 0.5. Therefore, 0 ≤ 𝑣 ≤ 0.5.
33
For God so loved the world that He gave His one and only Son,
that whoever believes in Him shall not perish but have eternal life.
John 3:16
34
For God so loved the world that He gave His one and only Son,
that whoever believes in Him shall not perish but have eternal life.
John 3:16
Engr. Marvin Bartido 1ST TERM AY 2023-2024
35
For God so loved the world that He gave His one and only Son,
that whoever believes in Him shall not perish but have eternal life.
John 3:16
36
For God so loved the world that He gave His one and only Son,
that whoever believes in Him shall not perish but have eternal life.
John 3:16
𝜖𝑙𝑎𝑡
For uniaxial loading in the x-direction, Poisson’s ratio is 𝑣 = − , where 𝜖𝑙𝑎𝑡
𝜖𝑙𝑜𝑛𝑔
is the lateral (transverse) strain.
𝝐𝒍𝒂𝒕 𝝐𝒛 𝝐𝒚
𝒗=− =− =−
𝝐𝒍𝒐𝒏𝒈 𝝐𝒙 𝝐𝒙
𝝈𝒙
𝝐𝒚 = 𝝐𝒛 = −𝒗𝝐𝒙 = −𝒗
𝑬
B. Multiaxial Loading
Biaxial Loading. Poisson’s ratio permits us to extend Hooke’s law for uniaxial loading to
biaxial and triaxial loadings.
37
For God so loved the world that He gave His one and only Son,
that whoever believes in Him shall not perish but have eternal life.
John 3:16
Triaxial Loading. Hooke’s law for the triaxial loading in Fig. 2.10 is
𝜎
obtained by adding the contribution of 𝜎𝑧 , 𝜖𝑧 = 𝑧 and 𝜖𝑥 = 𝜖𝑦 =
𝑣𝜎 𝐸
− 𝑧, to the strains in biaxial loadings, which yields
𝐸
𝟏
𝝐𝒙 = 𝝈𝒙 − 𝒗(𝝈𝒚 + 𝝈𝒛 )
𝑬
𝟏
𝝐𝒚 = 𝝈𝒚 − 𝒗(𝝈𝒙 + 𝝈𝒛 )
𝑬
𝟏
𝝐𝒛 = 𝝈𝒛 − 𝒗(𝝈𝒙 + 𝝈𝒚 )
𝑬
Note: For all the equations here in this discussion, they are valid for
both tensile and compressive effects. It is only necessary to assign
positive signs to elongations and tensile stresses and, conversely,
negative signs to contractions and compressive stresses.
38
For God so loved the world that He gave His one and only Son,
that whoever believes in Him shall not perish but have eternal life.
John 3:16
39
For God so loved the world that He gave His one and only Son,
that whoever believes in Him shall not perish but have eternal life.
John 3:16
Engr. Marvin Bartido 1ST TERM AY 2023-2024
Therefore:
𝒑
𝒆=−
𝒌
40
SAMPLE PROBLEMS
1. A bar made of A-36 steel has the dimensions shown in Fig. 3–22. If
an axial force of 𝑃 = 80 𝑘𝑁 is applied to the bar, determine the change
in its length and the change in the dimensions of its cross section after
applying the load. The material behaves elastically.
Engr. Marvin Bartido 1ST TERM AY 2023-2024
41
SAMPLE PROBLEMS
1
Find: 𝜖𝑦 = 𝜎𝑦 − 𝑣𝜎𝑥
𝐸
new length, width, and 1
𝜖𝑦 = ሾ−500 𝑀𝑃𝑎 −
thickness after application of the 120000 𝑀𝑃𝑎
0.34(800 𝑀𝑃𝑎)ሿ
load 𝜖𝑦 = −0.00643
𝑣
Solution: 𝜖𝑧 = −
𝐸
𝜎𝑥 + 𝜎𝑦
0.34
By inspection, the bar is 𝜖𝑧 = − (800 𝑀𝑃𝑎 −
120000 𝑀𝑃𝑎
subjected to a state of plane 500 𝑀𝑃𝑎)
stress. From the loading we have 𝜖𝑧 = −0.000850
𝜎𝑥 = 800 𝑀𝑃𝑎 (tension)
𝜎𝑦 = −500 𝑀𝑃𝑎 (compression) The new bar length, width, and
thickness are therefore
𝜎𝑧 = 0 𝜖=
𝛿
𝐿
The associated normal 𝑎′ = 300 𝑚𝑚 + 0.00808(300 𝑚𝑚)
strains are determined from the 𝑎′ = 302.424 𝑚𝑚
generalized Hooke’s law, that is,
1
𝜖𝑥 = 𝜎𝑥 − 𝑣𝜎𝑦 𝑏 ′ = 50 𝑚𝑚 + (−0.00643)(50 𝑚𝑚)
𝐸
1
ሾ800 𝑀𝑃𝑎 − 𝑏 ′ = 49.6785 𝑚𝑚
𝜖𝑥 =
120000 𝑀𝑃𝑎
0.34(−500 𝑀𝑃𝑎)ሿ
𝑡 ′ = 20 𝑚𝑚 +
𝜖𝑥 = 0.00808 (−0.000850)(20 𝑚𝑚)
𝑡 ′ = 19.983 𝑚𝑚
42
SAMPLE PROBLEMS
Find:
principal strains
Solution:
𝜎𝑥 = −15 𝑘𝑠𝑖
𝜎𝑦 = −26 𝑘𝑠𝑖
𝜎𝑧 = 10 𝑘𝑠𝑖
1
𝜖𝑥 = 𝜎 − 𝑣(𝜎𝑦 + 𝜎𝑧 )
𝐸 𝑥
1
𝜖𝑥 = ሾ−15 𝑘𝑠𝑖 −
10000 𝑘𝑠𝑖
0.33(−26 𝑘𝑠𝑖 + 10 𝑘𝑠𝑖)ሿ
𝜖𝑥 = −0.000972
1
𝜖𝑦 = 𝜎𝑦 − 𝑣(𝜎𝑥 + 𝜎𝑧 )
𝐸
1
𝜖𝑦 = ሾ−26 − 0.33(−15 +
10000
10)ሿ
𝜖𝑦 = −0.002435
1
𝜖𝑧 = 𝜎𝑧 − 𝑣(𝜎𝑥 + 𝜎𝑦 )
𝐸
1
𝜖𝑧 = 10 − 0.33(−15 − 26)
10000
𝜖𝑧 = 0.002353
43
SAMPLE PROBLEMS
Solution:
𝛿𝑎 = −0.00333 (4 𝑖𝑛)
Dilatation. The dilatation can be
𝛿𝑎 = −0.01332 𝑖𝑛
determined with 𝜎𝑥 = 𝜎𝑦 =
𝜎𝑧 = 20 𝑝𝑠𝑖. We have
1−2𝑣 𝛿𝑏 = −0.00333 (2 𝑖𝑛)
𝑒= (𝜎𝑥 + 𝜎𝑦 + 𝜎𝑧 )
𝐸
1−2(0.45)
𝛿𝑏 = −0.00666 𝑖𝑛
𝑒= 3(−20 𝑝𝑠𝑖)
600 𝑝𝑠𝑖
𝑒 = −0.01 𝑖𝑛3 /𝑖𝑛3 𝛿𝑐 = −0.00333 (3 𝑖𝑛)
𝛿𝑐 = −0.00999 𝑖𝑛
Change in Length. The normal
strain on each side can be The negative signs indicate that
determined from Hooke’s law; each dimension is decreased.
that is,
1
𝜖= 𝜎𝑥 − 𝑣(𝜎𝑦 + 𝜎𝑧 )
𝐸
1
𝜖= ሾ−20 𝑝𝑠𝑖 −
600 𝑝𝑠𝑖
0.45(−20𝑝𝑠𝑖 − 20𝑝𝑠𝑖)ሿ
𝜖 = −0.00333 𝑖𝑛/𝑖𝑛
44
For God so loved the world that He gave His one and only Son,
that whoever believes in Him shall not perish but have eternal life.
John 3:16
45
For God so loved the world that He gave His one and only Son,
that whoever believes in Him shall not perish but have eternal life.
John 3:16
46
SAMPLE PROBLEMS
1. Consider the bar shown in figure (a) which is fixed supported at both
of its ends. If P = 40 kN, 𝐿𝐴𝐶 = 600 𝑚𝑚, 𝐿𝐶𝐵 = 800 𝑚𝑚, 𝑑 = 12 𝑚𝑚
and 𝐸 = 200 𝐺𝑃𝑎, determine the reactions at support A and B.
Engr. Marvin Bartido 1ST TERM AY 2023-2024
Find:
Reactions at support A and B Hooke’s law
𝛿𝐴 − 𝛿𝐵 = 0
𝐹𝐴 𝐿𝐴𝐶 𝐹𝐵 𝐿𝐶𝐵
Solution: − = 0
𝐴𝐴𝐶 𝐸 𝐴𝐶𝐵 𝐸
Equilibrium 𝐹𝐴 (600 𝑚𝑚)
𝜋 −
12 𝑚𝑚 2 (200000 𝑀𝑃𝑎)
4
𝐹𝐵 (800 𝑚𝑚)
𝜋 =0
12 𝑚𝑚 2 (200000 𝑀𝑃𝑎)
4
0.000026526𝐹𝐴 −
0.000035368𝐹𝐵 = 0
𝐹𝐴 = 1.33332 𝐹𝐵
From eq. 1
σ 𝐹𝑉 = 0 ↑ + 𝐹𝐵 + (1.33332 𝐹𝐵 ) − 40000 =
0
𝐹𝐵 + 𝐹𝐴 − 40000 𝑁 = 0 (eq.
1) 𝐹𝐵 = 17142.96 𝑁
Compatibility 𝐹𝐴 = 1.33332(17142.96)
𝛿𝐴 − 𝛿𝐵 = 0 𝐹𝐴 = 22857.04 𝑁
47
SAMPLE PROBLEMS
Compatibility
For the deformations to be compatible, the
changes in the lengths of the steel rods and
the concrete must be equal; that is 𝛿𝑠𝑡 =
𝛿𝑐𝑜 . Because the lengths of steel and
concrete are identical, the compatibility
equation, written in terms of strains, is
Find: 𝜖𝑠𝑡 = 𝜖𝑐𝑜 (eq. 2)
Stress in each material (𝜎𝑠𝑡 , 𝜎𝑐𝑜 )
Hooke’s law
Solution: From Hooke’s law, eq. 2 becomes
𝜎𝑠𝑡 𝜎
Equilibrium 𝐸
= 𝐸𝑐𝑜
𝑠𝑡 𝑐𝑜
The FBD in the figure was drawn by isolating 𝐸
𝜎𝑠𝑡 = 𝐸𝑠𝑡 𝜎𝑐𝑜
the portion of the post above section a-a, 𝑐𝑜
where 𝑃𝑐𝑜 is the force in the concrete and 200000 𝑀𝑃𝑎
𝑃𝑠𝑡 denotes the total force carried by the 𝜎𝑠𝑡 = 𝜎
14000 𝑀𝑃𝑎 𝑐𝑜
steel rods. 𝜎𝑠𝑡 = 14.28571 𝜎𝑐𝑜
From eq. 1
For equilibrium, we must have 𝜎𝑠𝑡 𝐴𝑠𝑡 + 𝜎𝑐𝑜 𝐴𝑐𝑜 = 1000 103
σ 𝐹𝑉 = 0 ↑ + 14.285713 𝜎𝑐𝑜 (3600) + 𝜎𝑐𝑜 (86400) =
𝑃𝑠𝑡 + 𝑃𝑐𝑜 − 1000 103 𝑁 = 0 1000 10
𝜎𝑐𝑜 = 7.25539 𝑀𝑃𝑎
which, written in terms of stresses,
becomes 𝜎𝑠𝑡 = 14.28571(7.25539)
𝜎𝑠𝑡 𝐴𝑠𝑡 + 𝜎𝑐𝑜 𝐴𝑐𝑜 = 1000 103 𝑁 (eq. 1) 𝜎𝑠𝑡 = 103.648 𝑀𝑃𝑎
48
SAMPLE PROBLEMS
3. The steel rod shown in figure (a) has a diameter of 10 mm. It is fixed
to the wall at A, and before it is loaded, there is a gap of 0.2 mm
between the wall at and the rod. Determine the reactions at A and B’ if
the rod is subjected to an axial force of P=20 kN as shown. Neglect the
size of the collar at C. Take 𝐸𝑠𝑡 = 200 𝐺𝑃𝑎.
Engr. Marvin Bartido 1ST TERM AY 2023-2024
Substituting to eq. 2
0.2 = 0.000025465 (−𝐹𝐵 + 20000) −
σ 𝐹𝐻 = 0 → + 0.000050930 𝐹𝐵
𝐹𝐵 = 4048.69 𝑁
−𝐹𝐴 − 𝐹𝐵 + 20000 𝑁 = 0 (eq.
1)
𝐹𝐴 = −𝐹𝐵 + 20000
𝐹𝐴 = 15951.31 𝑁
Compatibility
Since the answer for 𝐹𝐵 is positive, indeed end B
The force P causes point B to move contacts the wall at B’ as originally assumed.
to B’ with no further displacement.
Therefore the compatibility NOTE: If 𝐹𝐵 were a negative quantity, the
condition for the rod is problem would be statically determinate, so
that and 𝐹𝐵 = 0 and 𝐹𝐴 = 20 𝑘𝑁.
𝛿𝐵/𝐴 = 0.2 𝑚𝑚
0.2 𝑚𝑚 = 𝛿𝐴 − 𝛿𝐵
49
SAMPLE PROBLEMS
4. The three A-36 steel bars shown in the figure are pin connected to a
rigid member. If the applied load on the member is 15 kN, determine
the force developed in each bar. Bars AB and EF each have a cross-
sectional area of 50 𝑚𝑚2 , and bar CD has a cross-sectional area of
30 𝑚𝑚2 .
Engr. Marvin Bartido 1ST TERM AY 2023-2024
Find: Compatibility.
Force developed in each bar The applied load will cause the horizontal
line ACE shown in figure (c) to move to the
inclined line A’C’E’. The displacements of
points A, C, and E can be related by similar
Solution: triangles.
Equilibrium.
The free-body diagram of the rigid
member is shown in Fig. 4–14b. This
problem is statically indeterminate
since there are three unknowns and
only two available equilibrium
equations. Thus the compatibility equation that relates
these displacements is
𝛿𝐴 −𝛿𝐸 𝛿 −𝛿
𝐶 𝐸
= 400
800 𝑚𝑚 𝑚𝑚
𝐶𝛿 −𝛿
𝐸
𝛿𝐴 − 𝛿𝐸 = 400 (800 𝑚𝑚)
𝑚𝑚
𝛿𝐴 = 2𝛿𝐶 − 2𝛿𝐸 + 𝛿𝐸
𝛿𝐴 = 2𝛿𝐶 − 𝛿𝐸
σ 𝐹𝑉 = 0 ↑ + Hooke’s law
𝐹𝐴 𝐿𝐴𝐵 𝐹 𝐿 𝐹 𝐿
𝐹𝐴 + 𝐹𝐶 + 𝐹𝐸 − 15000 = 0 (eq. 1) 𝐴𝐴𝐵 𝐸
= 2 𝐴𝐶 𝐶𝐷 − 𝐴𝐸 𝐸𝐹
𝐶𝐷 𝐸 𝐸𝐹 𝐸
𝐹𝐴 (500 𝑚𝑚)
50 𝑚𝑚2 (200000 𝑁ൗ𝑚𝑚2 )
=
σ 𝑀𝐴 = 0 ↻ + 2
𝐹𝐶 (500 𝑚𝑚)
−
30 𝑚𝑚2 (200000 𝑁ൗ𝑚𝑚2 )
15000 𝑁 200 𝑚𝑚 − 𝐹𝐸 (500 𝑚𝑚)
𝐹𝐶 400 𝑚𝑚 − 𝐹𝐸 800 𝑚𝑚 = 0 50 𝑚𝑚2 (200000 𝑁ൗ𝑚𝑚2 )
(eq. 2) 0.00005𝐹𝐴 = 0.00016667𝐹𝐶 − 0.00005𝐹𝐸
𝐹𝐴 = 3.3334𝐹𝐶 − 𝐹𝐸 (eq. 3)
50
SAMPLE PROBLEMS
From eq. 2
15000 𝑁 200 𝑚𝑚
− 𝐹𝐶 400 𝑚𝑚 − 𝐹𝐸 800 𝑚𝑚
=0
15000 𝑁 200 𝑚𝑚 −
(3461.49 𝑁) 400 𝑚𝑚 −
𝐹𝐸 800 𝑚𝑚 = 0
𝐹𝐸 = 2019.255 𝑁
From eq. 3
𝐹𝐴 = 3.3334(3461.49) −
2019.255
𝐹𝐴 = 9519.28 𝑁
51
For God so loved the world that He gave His one and only Son,
that whoever believes in Him shall not perish but have eternal life.
John 3:16
Thermal Deformation
52
For God so loved the world that He gave His one and only Son,
that whoever believes in Him shall not perish but have eternal life.
John 3:16
Conversion:
℃ = (℉ − 32)/1.8
℉ = ℃ × 1.8 + 32
𝐾 = ℃ + 273.15
53
SAMPLE PROBLEMS
1. The horizontal steel rod, 2.5 m long and 1200 𝑚𝑚2 in cross-sectional
area, is secured between two walls as shown in Fig. (a). If the rod is
stress-free at 20℃, compute the stress when the temperature has
dropped to −20℃. Use 𝛼 = 11.7 𝑥 10−6 /℃ and E = 200 GPa.
Assume that
(1) the walls do not move
(2) the walls move together a distance of ∆= 0.5 𝑚𝑚
Engr. Marvin Bartido 1ST TERM AY 2023-2024
Find: (2)
(1) Stress assuming that the walls do
not move Compatibility
(2) Stress assuming that the walls
move together a distance of ∆=
0.5 𝑚𝑚
Solution:
(1)
Compatibility
𝛿𝑇 − 𝛿𝑃 = ∆
Hooke’s law
𝜎𝐿
𝛼 ∆𝑇 𝐿 − =∆
𝐸
𝛿𝑇 = 𝛿𝑃 −6
11.7𝑥10 /℃ ሾ−20℃ −
20℃ ሿ 2500 𝑚𝑚 −
Hooke’s law: 𝜎 2500 𝑚𝑚
𝛿𝑇 = 𝛿𝑃
= 0.5 𝑚𝑚
200000 𝑀𝑃𝑎
𝜎𝐿 𝑃
𝛼 ∆𝑇 𝐿 =
𝐸
(𝜎 = )
𝐴
𝜎 = −53.6 𝑀𝑃𝑎
11.7𝑥10−6 /℃ ሾ−20℃ −
𝜎(2500 𝑚𝑚)
20℃ ሿ 2500 𝑚𝑚 =
200000 𝑀𝑃𝑎
𝜎 = −93.6 𝑀𝑃𝑎
54
SAMPLE PROBLEMS
2. The rigid beam shown in Fig. 4–19a is fixed to the top of the three
posts made of A-36 steel and 2014-T6 aluminum. The posts each have
a length of 250 mm when no load is applied to the beam, and the
temperature is 𝑇1 = 20℃. Determine the force supported by each post
if the bar is subjected to a uniform distributed load of 150 kN/m and
the temperature is raised to 𝑇2 = 80℃.
Engr. Marvin Bartido 1ST TERM AY 2023-2024
55
SAMPLE PROBLEMS
56
REFERENCES
57
ASSESSMENT TASK
1. The plate shown in Fig. 2–7a is fixed connected along AB and held in
Engr. Marvin Bartido 1ST TERM AY 2023-2024
the horizontal guides at its top and bottom, AD and BC. If its right side
CD is given a uniform horizontal displacement of 2 mm, determine (a)
the average normal strain along the diagonal AC, and (b) the shear
strain at E relative to the x, y axes.
58
ASSESSMENT TASK
3. If the applied force P causes the rigid arm ABC to rotate clockwise
about pin A through an angle of 0.02°, determine the normal strain
developed in wires BD and CE.
59
ASSESSMENT TASK
60
ASSESSMENT TASK
7. Data taken from a stress–strain test for a ceramic are given in the
table. The curve is linear between the origin and the first point.
Determine the modulus of elasticity and the modulus of resilience.
61
ASSESSMENT TASK
9. The A-36 steel bar shown in the figure is made from two segments
having cross-sectional areas of 𝐴𝐴𝐵 = 1 𝑖𝑛2 and 𝐴𝐵𝐷 = 2 𝑖𝑛2 .
Determine the vertical displacement of end A and the displacement of
B relative to C.
62
ASSESSMENT TASK
63
ASSESSMENT TASK
d. Change in Volume
14. Let the allowable stresses in the post be 𝜎𝑠𝑡 = 120 𝑀𝑃𝑎 and
𝜎𝑐𝑜 = 6 𝑀𝑃𝑎. Compute the maximum safe axial load P that may be
applied. The moduli of elasticity are 200 GPa for steel and 14 GPa for
concrete. Each steel bar has cross-sectional area of 900 𝑚𝑚2 .
P
64
ASSESSMENT TASK
15. The aluminum post shown in the figure is reinforced with a brass
core. If this assembly supports an axial compressive load of P = 9 kips
applied to the rigid cap, determine the average normal stress in the
aluminum and the brass. Take 𝐸𝑎𝑙 = 10 103 𝑘𝑠𝑖 and 𝐸𝑏𝑟 =
15 103 𝑘𝑠𝑖.
Engr. Marvin Bartido 1ST TERM AY 2023-2024
16. The figure shows a rigid bar that is supported by a pin at A and two
rods, one made of steel and the other of bronze. Neglecting the
weight of the bar, compute the stress in each rod caused by the 50-kN
load, using the following data:
65
ASSESSMENT TASK
17. Before the 400-kN load is applied, the rigid platform rests on two
steel bars, each of cross-sectional area 1400 𝑚𝑚2 , as shown in the
figure. The cross-sectional area of the aluminum bar is 2800 𝑚𝑚2 .
Compute the stress in the aluminum bar after the 400-kN load is
applied. Use 𝐸 = 200 𝐺𝑃𝑎 for steel and 𝐸 = 70 𝐺𝑃𝑎 for aluminum.
Neglect the weight of the platform.
Engr. Marvin Bartido 1ST TERM AY 2023-2024
18. The A-36 steel bar shown in Fig. 4–18a is constrained to just fit
between two fixed supports when 𝑇1 = 60℉. If the temperature is
raised to 𝑇1 = 120℉, determine the average normal thermal stress
developed in the bar.
66
ASSESSMENT TASK
19. Figure (a) shows a homogeneous, rigid block weighing 12 kips that
is supported by three symmetrically placed rods. The lower ends of
the rods were at the same level before the block was attached.
Determine the stress in each rod after the block is attached and the
temperature of all bars increases by 100℉. Use the following data:
Engr. Marvin Bartido 1ST TERM AY 2023-2024
67