Professional Documents
Culture Documents
NORME EUROPÉENNE
EUROPAISCHE N O R M November 1995
ICs 77.140.70
English version
--`,,```,,,,````-`-`,,`,,`,`,,`---
CEN
European Committee for Standardization
Comité Européen de Normalisation
Europäisches Komitee für Normung
O 1995. Copyright reserved to all CEN members. Ref. No. EN 10055: 1995 E
Contents
Page
Foreword . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
1 Scope . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
2 Normative references . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
3 Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
4 Designation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
5 Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
6 Tolerances on dimensions and s
7 Tolerances on mass . . .
8 Tolerances on length . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Foreword
This European Standard has been prepared by ECISS/TC 11 ‘Structural steel sections’, the Secretariat of which is held by
BSI. Its specifications are based on EURONORM 55.
This European Standard shall be given the status of a national standard, either by publication of an identical text or by
endorsement, and conflicting national standards withdrawn, by May 1996 at the latest.
In accordance with the CENKENELEC Internal Regulations, the following countries are bound to implement this European
Standard:
Austria, Belgium, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway,
Portugal, Spain, Sweden, Switzerland and United Kingdom.
1 Scope 4 Designation
This European Standard specifies requirements for the The designation of hot rolled equal flanged tees shall com-
nominal dimensions and the tolerances on dimensions, prise:
shape and mass of hot rolled steel equal flange tees with - the term ‘tee’;
radiused root and toes. These requirements do not apply to
- the number of this European Standard;
equal flange tees produced from stainless steel.
- the letter ‘T’;
- the height, h, in mm;
- number of quality standard and name or material
2 Normative references number of the steel ordered.
This European Standard incorporates, by dated or undated EXAMPLE:
reference, provisions from other publications. These nor-
mative references are cited at the appropriate places in the
Tee EN 1O 055 - T40 - steel EN 1O 025 - S235JR
text, and the publications are listed hereafter. For dated
references, subsequent amendments to or revisions of any 5 Dimensions
of these publications apply to this European Standard only Hot rolled equal flange tees with radiused root and toes as
when incorporated in it by amendment or revision. For un- covered in this European Standard shall be produced to the
dated references, the latest edition of the publication re- dimensions given in table 1 and illustrated in figure 1.
ferred to applies.
EN 10025 Hot rolled products of non-alloy structural 6 Tolerances on dimensions and shape
steels; technical delivery conditions
6.1 Section height
EN 10079 Definition of steel Droducts
Any deviations of the height, h, from the nominal value shall
be within the tolerances given in table 2.
--`,,```,,,,````-`-`,,`,,`,`,,`---
Y
--`,,```,,,,````-`-`,,`,,`,`,,`---
Y
Figure 1: Hot rolled steel equal flange tees with radiused root and toes
Table 1: Designation and dimensions of hot rolled steel equal flange tees with radiused root and toes
j
area
h b S, t I 11 12 d I, iY
Table 2: Tolerances on dimensions and shape of hot rolled steel equal flange tees with radiused root and toes
Dimensions in mm
Cross-sectional dimensions
b
I Nominal dimensions
1 b,h
Tolerances on
I s, t
b 5 50 I 1 f 0,5
Out-of-squareness, k
e=
bi - b2
Symmetry (eccentricity), e ~
2
____________
b < 60 e i l
60 < b e s 1,5
Tolerances
e% Nominal dimensions
50<b,h<100
Tolerances
q 5 0.4% of L
_ _ ~
Thickness Tolerances
4 5 s, t 5 7 -8%
7 < s, f - 6%