Professional Documents
Culture Documents
2)
FloWing
Eccentric Rotary Control Valve (Flange type)
Model VFR
OVERVIEW
The eccentric rotary control valve, “FloWing”
(model VFR), consists of a straight-through
valve body with minimal flow resistance and an
open yoke plug with a wing that rotates eccentri-
cally. The FloWing is suitable for applications
requiring a large flow capacity and wide range-
ability, and for the control of those slurry fluids
susceptible to clogging.
Also, the model VFR is able to control the
occurrence of cavitation when the liquid is
decompressed with high pressure reduction and
can decrease the level of noise and vibration.
The model VFR can effectively decompress the
liquid by inserting a perforated plate (anti-cavi-
tation plate) into the main body outlet side of the
valve. Therefore, cold and warm water with a
low or medium pressure line or process liquid
Bonnet
can be controlled even with a Kc value* over
Integral body type (-60 to +350°C)
0.55. Furthermore, for the anti-cavitation plate,
there are two types: the built-in type and the Gland type
Bolted gland
combined external type (model HRL).
Note) *: Please refer to selection guide for the anti- Packing/grease
cavitation specification. • Without grease….PTFE-inserted asbestos yarn
• With grease………Asbestos yarn or other packing
SPECIFICATIONS Note) PTFE: Polytetrafluoroethylene.
Trim
Body
Valve plug
Type
Eccentric rotary open yoke plug with wing
Straight-through
Seat ring
Valve size
Clamp seat ring
1, 1½, 2, 3, 4 or 6 inches
Material
Rating
For combinations of valve body, trim materials and fluid
• JIS 10K, 20K
temperatures, refer to Table 1.
• ANSI Class 150, 300
• JPI Class 150, 300
Connections
Flange type RF
Material
For combinations of valve body, trim materials and fluid
temperatures, refer to Table 1.
Specifications are subject to change without notice. -1- First issue: May. 2001 Rev.2: Mar. 2004
No. SS2-VFR110-0200 (Rev.2) Yamatake Corporation
Actuator Performance
Type Rated Cv value
Spring type pneumatic diaphragm actuator (model VR, RSA) Refer to Table 2 through Table 4 on page 4.
Action Flow characteristics
Direct or reverse action Refer to Figure 3.
Diaphragm Inherent rangeability
Chloroprene rubber reinforced with nylon fabric
100 : 1
Spring range Permissible differential pressure
80 to 160 kPa {0.8 to 1.6 kgf/cm2} or Refer to Table 5 and Table 6 on page 5.
180 to 270 kPa {1.8 to 2.8 kgf/cm2} (model VR3)
80 to 240 kPa {0.8 to 2.4 kgf/cm2} (model RSA1, 2)
Seat leakage rate
Note) Spring range and air supply pressure vary • Metal seat
according to nominal size. IEC-60534-4-1999 or JIS B 2007-1993
Class IV
Supply pressure Leakage less than 0.01% of maximum valve capacity,
340 to 490 kPa {3.5 to 5.0 kgf/cm2} or leakage less than 0.001% (optional)
Air connection • Soft seat
IEC-60534-4-1999 or JIS B 2007-1993
Rc¼
Class VI
Ambient temperature Leakage less than 0.00001% of maximum valve
-30°C to +70°C capacity.
Maximum diaphragm chamber capacity Hysteresis
• RSA1D (R) : 760 cm3 Within 1% F.S.
• RSA2D (R) : 3800 cm3 Linearity
• VR3D (R) : 5800 cm3 Within ± 2% F.S.
Valve action Operation speed (from fully closed to fully open)
Direct or reverse action • RSA1D (R) : 5 sec.
Positioner (optional) • RSA2D (R) : 7 sec.
• VR3D (R) : 21sec.
Model VPR pneumatic positioner or model SVP electro-
pneumatic positioner (Refer to their respective specifica- (With air supply pressure 340 kPa {3.5 kgf/cm2} for
tion sheets.) model RSA1, 400 kPa {4.0 kgf/cm2} for model RSA2 or
340 kPa {3.5 kgf/cm2} for VR 3, using model VPR posi-
Auxiliary devices (optional)
tioner and pressure regulator with filter, and with no
Pressure regulator with filter, handwheel, limit switch,
solenoid valve, valve position transmitter, volume booster, load.)
air lock valve, etc. (Refer to their respective specification Face-to-face dimensions
sheets and installation drawings.)
Refer to Figure 4 and Table 7.
Additional specifications (special order)
• Anti-cavitation plate (built-in type) External dimensions
• Special inspections Refer to Figure 4 and Table 7.
Flow characteristic inspection, material inspection
(Material certificate), non-destructive inspection, steam Weight
inspection, low temperature inspection Refer to Table 7.
• Oil/water free treatment
Mounting position
• Copper free treatment
• SUS304 stainless steel for bolts and nuts exposed to open air. Refer to Figure 6.
• Special air tubing and connections Finish
• Yoke material (SCPH12)*
Blue (Munsell 10B5/10) or silver, or other specified col-
• Brine-proof provisions
ors.
• Sand/dust-preventive provisions
• Tropical-area use specifications
• For use in areas susceptible to freezing
• Vacuum service
• For use in tropical areas
• Compliance to the High Pressure Gas Control Law
Note) *: Carbon steel (A216WCB) is a standard
yoke material for actuator mode RSA.
-2-
Yamatake Corporation No. SS2-VFR110-0200 (Rev.2)
10
8
6
4 Anti-cavitation
2 model VFR
0
0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1
Cavitation number Kc
Anti-cavitation plate Anti-cavitation plate (model HRL)
Figure 1 Noise control efficiency (dBA)
Figure 2
Table 1 Valve body and trim materials, and fluid temperatures (°C)
Components Material
Valve JIS SCPH2 SCS13A SCS14A
body ASTM A216WCB A351 CF8 A351 CF8M
Valve plug SCS24 SCS14 Stellite SCS14 Stellite SCS14 Stellite
Seat ring SUS630 SUS316 SUS316 SUS316 SUS316 SUS316 SUS316 SUS316 SUS316 SUS316
(*4) PTFE (*4) PTFE Stellite (*4) PTFE Stellite (*4) PTFE
seat seat seat seat
Seat retainer SUS630 SUS316
Brain bearing SUS440C (*1, *2) SUS316 Stellite
Main bushing SUS440C (*1, *2) SUS316 Stellite
Valve stem SUS316 (*2)
Trims
-3-
No. SS2-VFR110-0200 (Rev.2) Yamatake Corporation
Table 4 Anti-cavitation plate model HRL single Cv value (formed between the flanges)
90 90 90
80 80 80
Cam-1 (VPR)
70 Full port 70 Unit-1 (SVP) 70
40% port+
Cv value (%)
Cv value (%)
Cv value (%)
60 60 60 Cam-1 (VPR)
Unit-1 (SVP)
50 50 50
40
40% port 40 40
30 30 30
20 20 20
Cam-2 (VPR) Full port +
10 Unit-2 (SVP direct action) Cam-2 (VPR)
10 10 Unit-2 (SVP direct action)
Unit-3 (SVP reverse action)
Unit-3 (SVP reverse action)
0 0 0
0 10 20 30 40 50 60 70 80 90 100 0 10 20 30 40 50 60 70 80 90 100 0 10 20 30 40 50 60 70 80 90 100
(Reverse action valve) (Reverse action valve)
Travel (%) 100 90 80 70 60 50 40 30 20 10 0 100 90 80 70 60 50 40 30 20 10 0
(Direction action valve) (Direction action valve)
Input signal (%) Input signal (%)
-4-
Yamatake Corporation No. SS2-VFR110-0200 (Rev.2)
Actuator
Air supply Differential pressure [by nominal size (inch)] kPa {kgf/cm2}
pressure Spring range
model Positioner
No.
kPa kPa {kgf/cm2}
1 1½ 2 3 4 6
{kgf/cm2}
Air supply Differential pressure [by nominal size (inch)] kPa {kgf/cm2}
Actuator pressure Spring range
kPa Positioner
model No. kPa {kgf/cm2}
1 1½ 2 3 4 6
{kgf/cm2}
-5-
No. SS2-VFR110-0200 (Rev.2) Yamatake Corporation
DIMENSIONS
Table 7 Dimensions and weight (Unit: mm)
Nominal
Actuator Weight
size Pressure rating K A P H G M N
model no. (kg)
(inches)
Note) 1) The H dimensions enclosed in the parentheses are for the spring range 80 to 160kPa {0.8 to 1.6kgf/cm2}.
2) Face-to-face dimensions of the anti-cavitation specification (built-in type) will not be changed.
Face-to-face Face-to-face
dimensions dimensions
-6-
Yamatake Corporation No. SS2-VFR110-0200 (Rev.2)
Table 8 Anti-cavitation plate model HRL: External dimensions and weight [Unit: mm]
Nominal
Pressure rating φD φd T1 *1 T2 H W T3 φF Weight (kg)
size
JIS 10K 67 0.34
1 JIS 20K 67 25 10 6 74 20 4 10 0.34
ANSI 150, 130 51 0.22
JIS 10K 81 0.49
1½ JIS 20K 81 40 10 6 74 20 4 10 0.49
ANSI 150, 130 73 0.41
JIS 10K 96 0.75
2 JIS 20K 96 50 10 6 74 20 4 10 0.75
ANSI 150, 130 92 0.7
JIS 10K 127 1.8
3 JIS 20K 132 78 15 6 88 30 6 14 1.8
ANSI 150, 130 127 1.7
JIS 10K 151 2.5
4 JIS 20K 160 98 15 6 88 30 6 14 2.6
ANSI 150, 130 157 2.3
JIS 10K 212 4.8
6 JIS 20K 230 149 15 6 114 40 8 20 5.4
ANSI 150, 130 216 4.7
Note) *1: Add the thickness of the gasket (3.2 mm) to the face-to-face dimensions of anti-cavitation plate model
HRL.
Figure 5
-7-
No. SS2-VFR110-0200 (Rev.2) Yamatake Corporation
Installation 0
x102kPo
4
LI
VE CO
VE
0: Indoor mounting
A
R
E
MU
UITS A R
ST BE K
1: Outdoor mounting
RC
CI
EP
T
LE TIG
H T W HI
2
0 4
x102kPo
* *
*
*
*
*
* *
*
*
* *
Figure 6 Mounting position of valve on process pipes b. Applicable to model VPR pneumatic
positioner only
Note) 1) The pressure regulator with filter is mounted vertically to the ground.
2) Specify mounting positions other than the above standard mounting positions with code number.
3) When installing indoor, weatherproof construction is not needed.
4) When the first 2 digits of the model number, which indicate the mounting angle type, are 50, 60, 70, 80, 01, 02, 03, 04, 05, 06, 07 or 08,
weatherproof construction is needed if installing outdoor.
5) When the first 2 digits of the model number, which indicate the mounting angle type, are 10, 20, 30 or 40, weatherproof construction is
not required whether it is outdoor or not.
Ordering Information
When ordering, please specify;
1) Model Number: VFR 8) Special requirements of oil / copper free treatment, etc.
2) Nominal size X full port or 40% port 9) Name of flow medium
3) Rating of valve body and connection type 10) Normal flow and maximum flow
4) Materials of valve body and trims, and necessity of hardening 11) Pressure of flow medium, upstream and downstream pressure
treatment at fully closed and open positions
5) Type of actuator and air supply pressure 12) Process fluid temperature and specific gravity
6) Valve action (direct or reverse) 13) Viscosity of flow medium, inclusive or exclusive slurry or
7) Accessories (positioner, pressure regulator with filter, etc.) flushing
Savemation
Totate international Building Saving through Automation
2-12-19 Shibuya
Shibuya-ku, Tokyo 150-8316
Japan
Tel : 81-3-3486-2310
Fax : 81-3-3486-2593
-8-
http://www.yamatake.com/
This has been printed on recycled paper.