Professional Documents
Culture Documents
5278Uenohara,Uenohara-shi
Yamanashi-Ken
UC
KR
409-0112Japan
くE
DeclarationofConformity
We,KodenElectronicsCo.,Ltd.;5278UenoharaUenohara-Shi,Yamanashi-Ken
409-0112,Japan
d
ecl
are
asm
anu
fac
tur
eru
nde
rou
rso
ler
esp
ons
ibi
lit
yth
att
he
KodenEchoSounderCVS-126
i
nte
nde
dfo
rus
eas
aMa
rin
eFi
shF
ind
erv
ess
els
tow
hic
hth
isd
ecl
ara
tio
nre
lat
esc
onf
orm
sto
the
fol
low
ing
s
tan
dar
dso
rot
her
nor
mat
ive
doc
ume
nts
ref
eri
ngt
oEU
dir
ect
ive
san
dUK
reg
ula
tio
ns
EU UK
ElectromagneticCompatibilitvDirective SI2016No.1091ElectromagneticCompatibilitv
2014/30/EU Regulations2016
EMC EMC
IEC60945Ed.4.02002(Clauses9,10&12; IEC60945Ed.4.02002(Clauses9,10&12)
Forassessment,see
TestReportNo.YN0804003-1carriedoutbyChemitox-Yamanashl
EMCtestingatYamanashiIndustrialTechnologyCenter2094,wheretestarecarriedoutbyKoden
Personal
KodenTestside;KodenElectronicsCo.,Ltd.
RoHSconformity
EU UK
RoHSDirective2011/65/EUasamendedbvthe SI2012No、3032RoHSRegulations2012asamended
Commissiondelegateddirective(EU)2015/863
Typenames:CVS-I2S
Consistingof:DisplayUnit:CVS-126
PowerCable:CW-264A-2M
・Software:DispIayUnit:KM-E67Ver・xx.xx(xusedaswildcard
・Frequency:50kHzand200kHz
A
uth
ori
zed
rep
res
ent
ati
ve KodenElektronikGmbH
AmGewerbepark15,D-64823Gross-Umstadt,Germany
Pointofcontact KodenElectronicsCo.,Ltd.
5278Uenohara,Uenohara-shi,Yamanashi-Ken,Japan
Mr.JunHarayama,Manager,QualityAssuranceDept.
Tel.:+81554205860Fax:+81554205875
Date:17October,2022
Thiscertificateexpiresifnewregulationscome
inforceorlatestat31December2027
”細/〃b,金
j
耐Ha
raV
ama
/
Manager/QualityAssuranceDepartment DocumentNo.82-2731U-X008
CVS-126 Revision History
0093132702-10 i
Important Notice CVS-126
Important Notice
For copy and transcription of this Operation Manual (hereinafter referred to as this manual),
permission from Koden is needed. Koden prohibits the un-authorized copy and transcription of this
manual.
If this manual is lost or damaged, consult a dealer of Koden or Koden.
The specification of the products and the contents in this manual are subject to change without
notice.
The contents displayed on the menu of product may be different from the expression of this
manual. The fonts and shapes of the keys and menus in the illustration may differ from the actual
ones, and some parts may be omitted.
Koden is not liable for damages and troubles arisen from misunderstanding of the contents in this
manual.
Koden is not liable for any damages caused by earthquake, lightning, wind and flood damage and
fire for which Koden is not responsible, and actions by third parties, other accidents, customer’s
unintended error/abuse and the use under other abnormal conditions.
Koden is not liable for damages of accompaniment (change/loss of memorized content, loss of
business profit, stop of business) arisen from use or failure of our products.
If the stored data are changed or lost, irrespective of causes of troubles and damages, Koden is
not liable for them.
Koden is not liable for any damages arisen from malfunction caused by combination of software
and connected equipment in which Koden is not engaged.
ii 0093132702-10
CVS-126 For Your Safe Operation
Be careful of dust
Inhaling dust may cause A respiratory disease. When cleaning the inside of
equipment, be careful not to inhale dust. Wearing a safety mask is
recommended.
0093132702-10 iii
For Your Safe Operation CVS-126
Install the transducer at the location where it is not affected by bubble and
noise The bubble and noise seriously degrade the performance of this unit.
In case of smoke or fire, boat power off and the power of this unit. It may
cause fire, electric shock or damage.
Use the specified fuse. If un-specified fuse is used, it may cause a fire,
smoke or damage.
iv 0093132702-10
CVS-126 Contents
Contents
Document Revision History .......................i Setting the range switching to
Important Notice ....................................... ii Manual range ............................. 1-9
For Your Safe Operation ......................... iii 1.7 Setting of Shift............................ 1-9
Contents ...................................................v Setting of Manual Shift ............... 1-9
Release of manual Shift ........... 1-10
Introduction ................................................ ix
Setting of Auto Shift ................. 1-10
System Configuration ................................. x 1.8 Gain Adjustment....................... 1-10
Configuration of Equipment ....................... xi Basic Operation of Gain ........... 1-11
Selecting the auto gain ............ 1-11
Chapter 1 Basic Operation ......................1-1
Adjusting the gain by auto ....... 1-11
1.1 How to use the key .................... 1-1
Selecting the manual gain ....... 1-11
How to remove the hard cover... 1-2
Manual adjustment of the gain. 1-11
When removing the CVS-126
1.9 Use of [EVENT] key ................. 1-12
Display unit ................................ 1-2
Selecting the event
The clean of CVS-126
key function .............................. 1-12
Display unit ................................ 1-2
Presetting the waypoint ........... 1-12
1.2 Power On/Off ............................. 1-3
Store the image........................ 1-13
Power on .................................... 1-3
Fishing hot spot........................ 1-13
Power off .................................... 1-3
1.10 Use of [FUNC] key ................... 1-14
Alarm of Power Voltage ............. 1-3
Selecting the [FUNC] key ........ 1-14
1.3 LCD Brilliance Adjustment ......... 1-4
Preset of [FUNC] key ............... 1-14
Adjustment of LCD Brilliance ..... 1-4
1.11 Operation of VRM .................... 1-15
Brightness Adjustment of Panel
1.12 Display of fish information ........ 1-15
Brilliance .................................... 1-4
Display the fish symbol / stop the
1.4 Switch-over of Display mode ..... 1-4
display of fish symbol ............... 1-16
Normal Image (Low frequency,
Selecting the symbol info ......... 1-16
High frequency).......................... 1-4
Fish symbol detection
Dual frequency ........................... 1-5
adjustment ............................... 1-16
Zoom (Low frequency, High
Size adjustment ....................... 1-16
frequency) .................................. 1-5
Big fish / Big fish color ............. 1-17
Navigation Menu (NAV1, NAV2) 1-7
Points to note in use of fish
1.5 Selection of NAV Display ........... 1-8
symbol ...................................... 1-17
Type of NAV Display .................. 1-8
Selection of NAV Menu .............. 1-8 Chapter 2 How to use the Menu ............. 2-1
1.6 Switch-over of Range ................ 1-9 2.1 How to operate the menu .......... 2-1
Setting the range switching to auto Display the menu / Stop the
range .......................................... 1-9 display of menu .......................... 2-1
0093132702-10 v
Contents CVS-126
vi 0093132702-10
CVS-126 Contents
0093132702-10 vii
Contents CVS-126
viii 0093132702-10
CVS-126 Introduction
Introduction
The CVS-126 is a Dual frequency (50kHz/200kHz) Color LCD display echo sounder.
This unit equipped with digital process displays the circumstance in the water under all conditions,
matching with the high luminance 5.7 inch LCD.
The main features of this unit are as follows.
With the digital reception process, the compatibility of the high resolution in a shallow depth and the
noise rejection capability in a deep depth are established. The auto mode function provides the best
image.
The high-performance LCD maintains high visibility under any conditions.
The unit can be installed in an open bridge and is highly waterproof.
Sona-ToneTM (Sonar sound) function is equipped with for catching situations schools of fish and
others by sound.
Up to 10 images can be stored. If you connect the optional GPS, the homing function, that directs
your boat to navigate easily to the location desired, is available by marking the event mark when
recalling the stored image.
The unit is designed to save power consumption. The white LED is adopted for illuminating the LCD
and the power consumption is minimal in this class. The unit emits less heat and the occurrence of
condensation is rare.
The various alarm functions are available. (Bottom, school of fish, water temperature*, board
speed*, arrival*, XTE*, power) (Note: The mark * denotes that the connection of option is
mandatory)
When flush-mounting, the unit can be easily installed from front side.
0093132702-10 ix
System Configuration CVS-126
System Configuration
Connection Diagram
Legend
Standard configuration
Option
To Transducer Owner supply
connector
(TD connector) To POWER connector
CW-264A-2M
Red
+
10.8 to 31.2VDC
Black -
x 0093132702-10
CVS-126 Configuration of Equipment
Configuration of Equipment
0093132702-10 xi
Configuration of Equipment CVS-126
Essential Option
No Name of item Type Remark Weight/ Quantity
Length
1 Transducer Type of transducer transducer cable (with 9m 1
connector at one end)
Type of transducer
No Specification Frequency Material / Mounting method Beam width
Length of (Right and left x back
the cable Note and forth)
1 TD-500T-2B 50/200 kHz Plastic Inner-hull 50kHz
600 W 50°x50° ( -6dB)
9m
200kHz
17°x17° ( -6dB)
Option List
No Name of Item Specification Remark Weight/Length
1 Water temperature ST-80 For transom mounting 0.3kg/
sensor / speed Plastic made (with cable) 8m
sensor ST-90 For Through-hull mounting 0.6kg/
Plastic made (with cable) 8m
ST-100 For Through-hull mounting 1.2kg/
Bronze made (with cable) 8m
2 GPS sensor GPS-21-B For GPS measuring
0.6 kg / 10 m
(With power & signal cable)
3 Inner-hull kit MFB-04 Plastic made for installing the 1.3kg
transducer TD-500T-2B
4 Cable for transducer CW-840-0.3M Needed when using the 30cm
optional water temperature
sensor / speed sensor.
5 Connector for GPS BD-06PMMP-LC7001 Needed when using the
sensor GPS-21 (Type B) sensor.
xii 0093132702-10
CVS-126 Chapter 1 Basic Operation
3
5
4
6
Various setting can be done directly. The menu list closes automatically after the key operation of the
other keys than [menu].
0093132702-10 1-1
Chapter 1 Basic Operation CVS-126
Claw
1-2 0093132702-10
CVS-126 Chapter 1 Basic Operation
L H
School of fish Oscillation line
Fish
0093132702-10 1-3
Chapter 1 Basic Operation CVS-126
Disp
1.3 LCD Brilliance Adjustment
NAV1
Normal (H)
Adjustment of LCD Brilliance Zoom (H)
The brilliance of the display can be adjusted to Dual Freq
facilitate visualization. Zoom (L)
Normal (L)
The [Lcd brill] and [Panel brill] can be switched NAV2
every time when pressing the [BRILL ] key.
1 Press the [BRILL ] key for a short period of (H): High frequency
time to display the menu ([Lcd brill]).
(L): Low frequency
2 Rotate the [Knob]. When “1” is selected, it is
darkest. When “10” is selected, it is NAV1: Navigation display1
brightest. NAV2: Navigation display2
Lcd brill 3 Press the [MENU] key to close the menu.
10
1-4 0093132702-10
CVS-126 Chapter 1 Basic Operation
Dual frequency
The High frequency image can be displayed in
the right half side and the Low frequency image
Low frequency image
can be displayed in the left half side. Since the High frequency image
beam width differs depending on frequency, the
schools of fish and sea bottom look different.
Caution: The low frequency screen can be
displayed in the right half of the sceen
by replacing the screen and the high
frequency screen is displayed in the
left harf. (See [2.17 Explanation of
Menu Item, Image Swap])
Bottom It is convenient to see the It displays the position of It displays the bottom and
schools of fish near the the bottom in the fixation upper in the zoom.
bottom. in the display bottom part.
Bottom It is convenient to see the It displays the position of It displays the bottom and
Discrimination schools of fish and a the bottom in the fixation upper in the zoom, it
bottom quality near the in the position of 1/4 displays under the bottom in
bottom. under the display. the ordinary.
(Under the bottom, it doesn't
display in the zoom).
Zoom It is convenient to see the It displays a zoom start It displays in the zoom from
specified range in the position in the fixation at the zoom start position to the
zoom. the top of the display. range you set.
Bottom Zoom It is convenient to see the It displays the position of It displays upper side of the
schools of fish near the the bottom in the position bottom in the zoom except
bottom and the form of which is the same as the the bottom.
the bottom. ordinary display.
Bottom Follow It is convenient to see the It always displays the It displays the bottom and
Zoom schools of fish near the position of the bottom in upper and lower sides in the
bottom and the form of the lower part of the zoom.
the bottom. display.
0093132702-10 1-5
Chapter 1 Basic Operation CVS-126
Zoomed range
30.0
Zoom image
Zoomed range
30.0
Zoom image
Zoomed range
30.0
Zoom image
1-6 0093132702-10
CVS-126 Chapter 1 Basic Operation
The display width of zoom
is displayed in orange.
(4) Bottom Zoom Normal image
Zoomed range
30.0
Zoom image
The image below the bottom
is not zoomed.
(5) Bottom Follow Zoom The display width of zoom
is displayed in orange.
Normal image
Zoomed range
30.0
Zoom image
Navigation Menu (NAV1, NAV2)
The navigation menu can be displayed on the left side of the display. To display the information other
than depth, sensors need to be connected. (See [1.5 Selection of NAV Display])
Caution: Requires position data from GPS sensor.
10.0 10.0
水温
20.0 Water temp 20.0
30.0 30.0
進路
Course
40.0 H:9.0 40.0
50.0 173.0°50.0
コースずれ
XTE
60.0 60.0
STAB 0.28 70.0
70.0
0093132702-10 1-7
Chapter 1 Basic Operation CVS-126
Lat/Lon Depth
NAV1
Display1
Display2
Boat speed Display3
Speed meter Display4
HDG
Wind dir.
Display1
Simple plotter
Heading, XTE, Time Compass
required, Wind dir., Wind
Speed meter
Wind speed speed, Depth, Lat/Lon,
Depth
Boat speed, Course,
Lat/Lon
RNG BRG, Water temp
Boat speed
Course
1-8 0093132702-10
CVS-126 Chapter 1 Basic Operation
Range
Setting the range switching to auto Auto range
range 5.0
By following automatically the bottom, the image 10.0
of echo sounder in the suitable range of 20.0
measured depth can be displayed. 50.0
100
This mode is convenient to display always the
160
range from sea level to bottom.
300
500
Auto shift
0093132702-10 1-9
Chapter 1 Basic Operation CVS-126
Range
Auto range
5.0
10.0
20.0
50.0
100
1 Press [FUNC] key twice. The shift function is 160
turned on.
300 Range
Shift 500
40.0
OFF Auto shift
ON
Release of manual Shift 5 Press the [MENU] key to close the menu.
When the [Auto shift] is set, the [R: AS] is
The shift function is released, and it returns it to displayed at the upper side of menu.
former screen.
1 Press twice the [FUNC] key. The shift
function is turned off. 1.8 Gain Adjustment
Shift
OFF The gain can be adjusted in the auto mode
ON [Cruising, Fishing] or manual mode.
[Cruising]
2 Press the [MENU] key to close the menu.
Eliminating the weak echo, it displays clearly the
sea bottom of strong echo.
It is suitable for cruising to the fishery ground.
Setting of Auto Shift
[Fishing]
The image is automatically shifted so that the
bottom is always displayed. It displays clearly the weak echo reflected from
the school of fish.
It is suitable for searching the schools of fish.
1 Press [ ] of [ ] key of [ RANGE ].
1-10 0093132702-10
CVS-126 Chapter 1 Basic Operation
0093132702-10 1-11
Chapter 1 Basic Operation CVS-126
3 When the [Disp] is set to other than [Dual EVENT key set
freq], every time when the [Knob] is pressed, Store
the [Gain (H)] or [Gain (L)] [Gain select] is
Store
displayed.
When the [Disp] is set to the [Dual freq], Fishing hot spot
every time when pressing the [Knob], the
[Gain (H)] or [Gain (L)] [Gain select] is 5 Press the [MENU] to close the menu.
displayed.
4 Press the [MENU] to close the menu. Presetting the waypoint
The latest set value of frequency (High frequency When you find the school of fish or tide, its
or Low frequency) adjusted is displayed at the location can be preset as a waypoint.
upper left side of menu. (10 locations at maximum)
Example: When presetting the waypoint, switch [System]
The High frequency gain is 8.0 H: 8.0. [EVENT Key set] [Store pos]. (See [1.9 Use
H: 8.0 R: M 12.6 V of [EVENT] key Selecting the event key function])
1 In the state that no other key is pressed,
press the [ ] key or [ ] key.
1.9 Use of [EVENT] key 2 Move the cursor (red line) with the [ ] key or
[ ] key to the location to be preset as a
By pressing the [EVENT] key, three functions of waypoint.
[Store Position]. [Store Image] and [Fishing hot
spot] are available.
The fishing hot spot is the function to instruct L H
1-12 0093132702-10
CVS-126 Chapter 1 Basic Operation
0093132702-10 1-13
Chapter 1 Basic Operation CVS-126
5 To stop the fishing hot spot, cancel 4 Select the function. (Press the [ ] key or [ ]
destination navigation. (See: [2.14 Preset/ key)
WPT edit/ WPT delete of Waypoint], [Cancel
the NAV].)
1-14 0093132702-10
CVS-126 Chapter 1 Basic Operation
The VRM (movable marker) shown by the green For detection of fish information, 2 frequencies,
line can be moved up and down. 200 kHz and 50 kHz are used.
It is convenient to measure the depth by aligning Only in case echo comes up in both frequencies,
with the target such as school of fish. the detection can be made.
1 Press the [ ] key or [ ] key. The movable By [Symbol info], the magnitude and the value of
marker (straight line) is displayed. depth of the response can be displayed.
0093132702-10 1-15
Chapter 1 Basic Operation CVS-126
Caution: When the fish symbol function is Caution: The display of [Size] is
made effective, the image speed expressed in cm.
becomes 2 kinds ([Speed5 (1/1)] or
5 Press the [MENU] key to close the menu.
[Stop]).
Caution: The magnitude by [Symbol info]
Caution: Adjustment is necessary when
would not be always the response from
equipped with Inner-hull. (See [2.17
fish. And it may be incorrect due to
Explanation of Menu Item, Inner-hull].)
various environmental conditions.
Please take these as reference.
Display the fish symbol/Stop the Caution: The value of depth by [Symbol
display of fish symbol info] would not be always the response
from fish. That shows the point that there
1 Press the [MENU] key. was specific response.
2 Select [Display1] [Fish symbol]. (Press
the [ ] key or [ ] key or [ ] key.) (See [2.1 Fish symbol detection adjustment
How to operate the menu])
Detection of fish marks can be adjusted.
3 Press the [ ] key.
Select [Correct] [Detect adjust f].
4 Select the symbol to be displayed on the
screen. (Press the [ ] key or [ ] key)
Fish symbol
Symbol 1
Caution: If the larger the set values
become, the more fish marks can be
5 Press the [MENU] key to close the menu. displayed with more false
When this function is effective, the icon is detections.
displayed at the top of the screen. Caution: For Through-hull installation,
adjust between 1 and 4. For
Inner-hull installations, adjust
Caution: When [Fish symbol] on the between 3 and 6.
screen does not always mean that the
response shows fish.
Size adjustment
Selecting the symbol info The indicated size of fish marks can be adjusted.
[Symbol info] is effective only when [Fish symbol] Please correct the size when the indicated value
is displayed. is different from the fish that actually caught.
1 Press the [MENU] key. Select [Correct] [Size adjust].
2 Select [Display1] [Symbol info]. (Press
the [ ] key or [ ] key or [ ] key.) (See [2.1
How to operate the menu])
The indicated size will change by approximately
3 Press the [ ] key. 10 to 20 percent of the value, per one setting
4 Select the information associated with [Fish value.
symbol] (Press the [ ] key or [ ] key.)
1-16 0093132702-10
CVS-126 Chapter 1 Basic Operation
0093132702-10 1-17
- This page intentionally left blank.-
CVS-126 Chapter 2 How to use the menu
0093132702-10 2-1
Chapter 2 How to use the menu CVS-126
Image speed
Speed 1
Speed 2
OFF Weak Stron
Speed 3
Speed 4
Stop
Speed 5 (1/1) 1 Press the [MENU] key.
Speed 6
Speed 7 2 Select the [Adjust] [Interference Rejection].
Speed 8
(See [2.1 How to operate the menu].)
Speed 9 3 Press the [ ] key.
4 Change the setting of [Inference Rejection].
(Press the [ ] key or [ ] key.)
5 Press the [MENU] key to close the menu.
IR
OFF
Weak
Strong
2-2 0093132702-10
CVS-126 Chapter 2 How to use the menu
2.4 Color Rejection of Weak 5 Press the [MENU] key to close the menu.
Echo
2.6 Setting of Shift step
Color Rejection
The color of weak echo can be rejected. The shifting range is set by pressing the [ ]
key or [ ] key one time. (Setting range: 1m,
Rejecting noise on the entire image and weak 10m, 1/8, 1/4)
echo around the school of fish makes it easier
to see the school of fish. It is the convenient
function when displaying the echo stronger 1 Press the [MENU] key.
than the specific signal. (Setting: 0 ~ 50 %)
2 Select the [D.range] [Shift step]. (See
1 Press the [MENU] key. [2.1 How to operate the menu])
2 Select the [Adjust] [Color Rejection]. 3 Press the [ ] key.
(See [2.1 How to operate the menu])
4 Change the setting of [Shift step]. (Press
3 Press the [ ] key. the [ ] key or [ ] key.)
4 Change the setting of [Color Rejection].
(Press the [ ] key or [ ] key.)
Shift step
Color Rejection
1m
0 % 10m
1/8
1/4
5 Press the [MENU] key to close the menu.
0093132702-10 2-3
Chapter 2 How to use the menu CVS-126
Zoom type
2.9 Setting of Zoom Start
BTM.
B.D. Select the zoom start in the [Zoom].
Zoom
(See [1.4 Switch - over of Display mode])
B.Z.
B.F.Z. (Setting: m: 0 to 800, fm, I.fm: 0 to 800, ft: 0 to
2800)
5 Press the [MENU] key to close the menu.
For each zoom display, refer to [1.4 Switch-over
of Display mode]. Zoom Start
Zoom start
Zoom Range 10
0~800
0-800 m
4 Change the set value of [Zoom range]. Preset the set value suitable for your purpose.
(Press the [ ] key or [ ] key) (Setting range: m: 2.5 to 800, fm, I.fm: 2.5 to
Zoom Range 800, ft: 10 to 2800)
10.0
m 1 Press the [MENU] key.
5 Press the [MENU] key to close the menu. 2 Select [D.range]→[Range preset]→[Range
1 to 8]. (See [2.1 How to operate the
menu])
3 Press the [ ] key.
2-4 0093132702-10
CVS-126 Chapter 2 How to use the menu
Adjust 5.0
Prev m
D.range
Range 1 5.0 m
Disp1
Disp2
Range 2 10.0 m 5 When the [ ] key is pressed, it returns to
Alarm1 Range 3 20.0 m the [range]. Other detecting range can be
Alarm2 Range 4 50.0 m continuously changed.
NAV Range 5 100 m
Range 6 160 m
6 Press the [MENU] key to close the menu.
Image
System Range 7 300 m
Range 8 500 m
Next
Return 2.11 Setting of Background
Caution: Select [Forward], and press [ ] Color
key to return to the previous menu.
5 Press the [ ] key. Responding to the ambient brightness, the
background color of display can be changed.
6 Select the set value of [Range 1 to 8].
(Press the [ ] key or [ ] key) 1 Press the [MENU] key.
2 Select [Display1] [Background color].
Range1
(See [2.1 How to operate the menu])
20.0
3 Press the [ ] key.
m
4 Change the setting of [Background color].
7 Press the [MENU] key to close the menu. (Press the [ ] key or [ ] key)
Background color
Easy registration method of the Pale blue
Marine blue
range
Blue
1 Press [ ] or [ ] key of [ RANGE ]. Dark blue
Black
2 Change the range you desire to set. (Press
Darkkhaki
[ ] or [ ] key of [ RANGE ])
Mediumseagreen
Light grey
White
Range
Night mode
Auto range
5.0
10.0 5 Press the [MENU] to close the menu.
20.0
50.0
100 2.12 Setting of White Line
160
300
As the surface of bottom is marked with the
500
white line of constant width, the school of fish at
Auto shift
the bottom can be easily identified.
0093132702-10 2-5
Chapter 2 How to use the menu CVS-126
White line [XTE alarm] can be used in the state that the
OFF destination is set. The alarm is issued when your
1 boat is off a certain distance from the course on
2 the line drawn straightly from destination to the
3
location when setting the destination. A certain
distance is set in the [NAV alarm range].
4
5 Caution: In the [NAV alarm range], select
Auto the alarm range of [Arrival alarm]
and [XTE alarm]. (Setting: 5 to 999
5 Press the [MENU] key to close the menu.
m)
2-6 0093132702-10
CVS-126 Chapter 2 How to use the menu
[ Fish alarm]
1 Press the [MENU] key.
2 Select your desired alarm from [Alarm 1] or
[Alarm 2]. (See [2.1 How to operate the
menu].)
3 Press the [ ] key.
4 Select the [ON] of alarm you desire. (Press
the [ ] key or [ ] key)
5 If the setting of [Alarm range] is provided in
the alarm desired, select the alarm range.
(See [2.1 How to operate the menu])
6 Change the set value of alarm range.
(Press the [ ] key or [ ] key)
7 Press the [MENU] key to close the menu.
0093132702-10 2-7
Chapter 2 How to use the menu CVS-126
NAV start
NAV starts
Yes
No
2-8 0093132702-10
CVS-126 Chapter 2 How to use the menu
WPT delete
Yes
No
Caution: If the values of latitude and 7 Press the [MENU] key. Then, the
longitude are not entered, they are destination is deleted and the menu
registered as 0. closes.
8 To end editing, press [Knob].
9 After finishing the edit work, press the
[MENU] key.
Recall the stored image and preset it
10 Select the [registered] in the confirmation as a destination
menu. Recall the stored image in the past and it can
Edit end be preset as a destination. (See [1.9 Use of
Registered [EVENT] key])
Not registered 1 Press the [MENU] key.
11 Press the [MENU] key. Then, the edit is 2 Select [Image] [Image recall]. (See [2.1
finished. How to operate the menu].)
3 Press the [ ] key.
4 Select the image No. from the [Image
Delete the waypoint recall] list. (Press the [ ] key or [ ] key)
The destination list preset in the past can be
0093132702-10 2-9
Chapter 2 How to use the menu CVS-126
2-10 0093132702-10
CVS-126 Chapter 2 How to use the menu
Image recall
No. Comment 6 Select the [Yes] in the confirmation menu.
1 PIC0 00 01 Image delete
2 PIC0 00 02 Yes
3 PIC0 00 03 No
4 PIC0 00 04
5 PIC0 00 05
7 Press the [MENU] key.
6 PIC0 00 06
Then, the preset image is deleted.
7 PIC0 00 07
8 PIC0 00 08
9 PIC0 00 09
Add the comment to the stored
10 PIC0 0010
image
It is convenient to judge the stored image.
Caution: Chosen list NO. becomes
yellow. 1 Press the [MENU] key.
5 Press the [ ] key. 2 Select [Image] [Image comment]. (See
[2.1 How to operate the menu])
Caution: When other stored image exists
beside the recall image, switch to other 3 Press the [ ] key.
image with the [ ] and [ ] key. 4 Select the number of image to which the
6 Press the [MENU] key to return to the comment is added from the [Image
normal menu. comment]. (Press the [ ] key or [ ] key)
Image comment
Delete the stored image No. Comment
1 PIC00001
The stored image in the past can be deleted. 2 PIC00002
To delete, it takes some time. 3 PIC00003
4 PIC00004
1 Press the [MENU] key. PIC00005
5
2 Select [Image] [Image delete]. (See [2.1 6 PIC00006
How to operate the menu]) 7 PIC00007
3 Press the [ ] key. 8 PIC00008
9 PIC00009
4 Select the number of image to be deleted 10 PIC00010
from the [Image delete] list. (Press the [ ]
key or [ ] key)
5 Press the [ ] key.
Image delete 6 Select the character with the [ ] key or [ ]
No. Comment key. (Character: A ~ Z, blank, 0 ~ 9, +, -./)
1 PIC0 00 01
2 PIC0 00 02 Image comment
3 PIC0 00 03 No. Comment
4 PIC0 00 04 1 P I C00001
5 PIC0 00 05 2 P I C00002
6 PIC0 00 06 3 P I C00003
7 PIC0 00 07
8 PIC0 00 08
PIC0 00 09
7 Select the comment position with the [ ]
9
key or [ ] key.
10 PIC0 0010
0093132702-10 2-11
Chapter 2 How to use the menu CVS-126
Sona-tone
Sonar tone
OFF
ON
Connection of External Speaker 6 Press the [MENU] key to close the menu.
Connect the external speaker with amplifier Caution: Gain (TD) setting value widely
(option) so that you can hear the sonar easily. varies upon installation conditions
such as material of hull and
Caution: The Sona-ToneTM is always installation method. Low frequency
output. Adjust the speaker volume (50 kHz) may not be used due to large
with the volume provided on the signal attenuation in some cases.
speaker.
2-12 0093132702-10
CVS-126 Chapter 2 How to use the menu
0093132702-10 2-13
Chapter 2 How to use the menu CVS-126
Image Swap
Display the water temp graph/Stop
The images of echo sounder at the right and left
the display of water temp graph sides can be swapped.
The latest water temp value and the graph of 1 Press the [MENU] key.
past water temp data can be displayed.
2 Select the [Image] [Image swap]. (See
1 Press the [MENU] key. [2.1 How to operate the menu])
2 Select the [Display1] [Water temp 3 Press the [ ] key.
graph]. (See [2.1 How to operate the
menu]) 4 Select the swap state [A|B], [B|A]. (Press
the [ ] key or [ ] key)
3 Press the [ ] key.
5 Press the [MENU] key to close the menu.
4 To display the water temp graph, select the
[ON].
To stop the display of water temp graph,
select the [OFF]. (Press the [ ] key or [ ]
2-14 0093132702-10
CVS-126 Chapter 2 How to use the menu
0093132702-10 2-15
Chapter 2 How to use the menu CVS-126
2-16 0093132702-10
CVS-126 Chapter 3 How to use the menu2
Adjust
In out
D.range Correct
Display1
Setting
Display2
Maintain
Alarm1 Buzzer Setting
Alarm2
NAV Set the buzzer sound to ON/OFF.
Image
System
Next
Temp Source
Switch the Sensor/NMEA.
3 Press [ ] key to display the system menu.
Use the built-in water temp meter fot sensor.
Prev Adjust For setting of [NMEA], use the input value from
In out outside connected with NMEA of power
D.range
Correct connector.
Display1
Setting
Display2
Maintain
Alarm1
Alarm2 Speed Source
NAV
Image
Switch the Sensor/NMEA.
System Use the built-in speed meter for sensor.
For setting of [NMEA], use the input value from
outside connected with NMEA of power
connector.
0093132702-10 3-1
Chapter 3 How to use the menu2 CVS-126
3-2 0093132702-10
CVS-126 Chapter 3 How to use the menu2
Depth Unit
It switches the unit of depth to [m, fm, l.fm and ft].
Temperature Unit
It switches the unit of temperature to [˚C], [°F].
0093132702-10 3-3
Chapter 3 How to use the menu2 CVS-126
Initialize
It returns all the settings in the menu to the
factory settings. However, the memorized data of
display remains unchanged.
System Check
It is used for diagnostic test.
3-4 0093132702-10
CVS-126 Chapter 4 Maintenance and Inspection
4.1 Inspection
The daily maintenance and inspection extends the life of equipment. To always keep the equipment in
the best condition, implement periodically the inspection shown in the table below.
Item Content of Inspection
Connector at the rear of Check the looseness.
CVS-126 Display unit
Wiring of cables Check the wiring of cables connecting the equipment and the
damage of cable.
Grounding of display unit Scrape the rust off the ground terminal and make its contact well.
4.2 Cleaning
The display unit has a special coating. Do not use a solvent such as
Caution paint thinner, acetone, alcohol, and benzene, etc.
Strong rubbing may cause bruising or scratching.
For cleaning the housing, do not use plastic solvent such as thinner or alcohol. Painting on the surface
and characters at the operating portion may melt. After wiping with soft and clean cloth dipped with
diluted neutral detergent, wipe away with dry soft and clean cloth.
Transducer
In case of Through-hull equipped transducer, check the surface of opening of transducer (portion from
which the ultra-sonic is emitted). If shells and oil are stuck, scrub the surface with a wooden or bamboo
knife with caution not to damage the surface and remove stuck materials. If you scrub strongly, the
surface will be damaged, resulting in deteriorated performance of transducer.
0093132702-10 4-1
Chapter 4 Maintenance and Inspection CVS-126
If the input voltage is too high, the over-current flows or a trouble occurs inside, the fuse will blow out.
The fuse is housed in the power cable.
4-2 0093132702-10
CVS-126 Chapter 4 Maintenance and Inspection
ROM
RAM
NMEA OK NG
VOLT 2
TEMP
GAIN
SPEED
Diagnose
1 displays the diagnostic result.
The result of ROM and RAM check displays
OK when normal and NG when abnormal.
0093132702-10 4-3
- This page intentionally left blank.-
CVS-126 Chapter 5 Installation
Chapter 5 Installation
To realize the full performance of echo sounder, the installation of CVS-126 must be performed by an
engineer who is officially authorized by our company. The installation work includes the following
content.
(1) Unpacking the components
(2) Inspection of configuration unit, spare, accessories and material for installation
(3) Check of power voltage and capacity of current
(4) Decision of installing location
(5) Installation of CVS-126 Display unit and transducer
(6) Installation of accessories
(7) Plan and execution of cable laying and connection
(8) Adjustment after completion of installation
0093132702-10 5-1
Chapter 5 Installation CVS-126
The equipment is not waterproof. Avoid excessively damp place. Do not install
the equipment in the place suffering from excessive waterdrops. Otherwise,
the inside of display window mists over or corrosion may occur inside.
Caution: The ground side of power input of this equipment is connected to the ground
terminal.
In case of + (positive) ground, it cannot be used. The power may short-circuit.
(3) If you connect the power cable directly to the battery, the interference from other electronic
equipment is not subject to occurrence. (See Fig. 5.1.)
CVS-126 Display unit CVS-126 Display unit
Good example Bad example
Battery Battery
Noise Noise
5-2 0093132702-10
CVS-126 Chapter 5 Installation
Desk-top Installation
CVS-126 Display unit (1) Loosen the knob bolt fixing CVS-126 Display
Knob bolt
unit to the mounting bracket, push the unit to
Turn two turns the knob bolt to
the left side and pull the unit upward.
loosen it and pull the unit upward.
(2) Place the removed unit to a safe and flat
place.
Fixing screw x 4
(3) Place the mounting bracket on the location
for the unit to be installed and fix it with four
screws (trans-tapping screws) supplied with
installing materials.
(4) Connect the connectors for power and
Mounting bracket transducer to the unit respectively.
(5) Install the unit to the mounting bracket and fix
Fig. 5.2 Desk-top Installation the unit by turning clockwise the knob bolt
Flush-mount Installation
(1) Make a square hole (160mm x 160mm) at the location to be installed. (See Fig. 5.4.)
(2) Turn counter-clockwise the knob bolt fixing CVS-126 Display unit to the mounting bracket to
loosen it, push the unit to the left side and pull the unit upward. The mounting bracket and knob
bolt are not used.
(3) Confirm that the unit matches with the square holes. If not matched, correct the square hole.
(4) Remove the front frame of CVS-126 Display unit, pulling it toward you. (See Fig. 5.3.)
(5) Connect the connectors for power and transducer to the unit respectively.
(6) Install the CVS-126 Display unit in the installing location (square hole) and fix it with four tapping
screws (4mm) (M4 or pan-head). (Prepare 4mm screws suitable for thickness of installing
location.)
(7) Install the front frame removed in step (4).
0093132702-10 5-3
Chapter 5 Installation CVS-126
Threading hole
160 (6 19/64) x 160 (6 19/64)
R30
Front frame
Unit: mm (inch)
Figure 5.3 Flush-mount Installation
Unit: mm (inch)
5-4 0093132702-10
CVS-126 Chapter 5 Installation
In case of Inner-hull
Using the optional Inner-hull kit (MFB-04), install the transducer to the inner side of ship’s bottom.
Caution on installation
0093132702-10 5-5
Chapter 5 Installation CVS-126
Caution: Fishing boats may have structure with FRP contained air bubbles and foamed
materials that would prevent ultrasound from penetration. Therefore, the location
convenient for installation may not be locations where attenuation of ultrasound is low
enough.
In case of Through-hull
Install the transducer directly to the ship’s bottom
Installation Procedure
(1) Select the installing location.
(2) Remove the fixing nut and one piece of rubber packing.
(3) If the slope of ship’s bottom is greater than 5°, make a wooden base to fit to the slope of ship’s
bottom. To reduce the water resistance, cut the bow direction tip of wooden base at the outer side
of ship’s bottom in the triangle shape.
(4) Make holes at the installing location. If the wooden base is used, make holes in the wooden base.
(5) Thread the rubber packing in the transducer and then the cable.
(6) To prevent water from seeping through the gap between the transducer and the hole, fill out the
gap with FRP or silicon glue. (Glue the wooden base likewise.)
(7) Thread the rubber packing and fix it with the fixing nut firmly.
(8) Connect the transducer cable to the connector of CVS-126 Display unit.
Fixing nut
Rubber packing Fixing nut Rubber packing
Wooden base
,
Ship s bottom
Rubber packing Wooden base
Transducer Rubber packing ,
Ship s bottom
5-6 0093132702-10
CVS-126 Chapter 5 Installation
5.4 Wiring
Power input
10.8~31.2VDC
NMEA data input output
GPS, plotter etc
Sona-ToneTM output
POWER TD Line output for speaker with amplifier
Power output
For power of GPS etc
Transducer
For 50/200kHz in common
Speed sensor data input
Water temperature sensor data input
GND
0093132702-10 5-7
Chapter 5 Installation CVS-126
3A
DC+ (Red)
3A
DC- (Black)
Caution: Wind the insulation tape around the un-used lead wire for core-wires not to contact
each other.
Connection of transducer
To [TD] connector
Grounding
Use heavy gauge cable for grounding wire.
Connect the grounding wire to the grounding material in a short distance.
When connecting the external equipment of which positive polarity is connected to the ground line,
do not connect the ground of signal line to the cabinet ground.
5-8 0093132702-10
CVS-126 Chapter 5 Installation
0093132702-10 5-9
Chapter 5 Installation CVS-126
Shield To transducer
TD2 (White)
SPD.PULSE (Blue)
SPD.GND (Black)
lead wire
TEMP.VCC (Green)
To the water temperature sensor
TEMP.SIG (Red)
Caution: Wind the insulation tape around the un-used lead wire for core-wires not to contact
each other.
5-10 0093132702-10
CVS-126 Chapter 5 Installation
3A
3A
Input Data
The sentences of GGA, GLL, HDT, MTV, MWV, RMC, THS, VHW, VTG and ZDA can be received.
The type of NMEA0183 Ver.1.5, Ver.2.0 and Ver.3.0 can be inputted.
Information Priority Order of Sentence Information Priority Order of Sentence
Latitude, GGA > RMC > GLL Wind Direction MWV
Longitude
Course VTG > RMC Wind Speed MWV
Heading THS > HDT Date ZDA > RMC
Ground Speed VTG > RMC Time ZDA > GGA
Water Speed VHW Water MTW
Temperature
Output Data
The sentences of DBT, DPT, GGA, GLL, HDT, MTW, MWV, RMC, TLL, VHW, VTG and ZDA can be
transmitted.
The output is performed in the type of NMEA0183 Ver.2.0/3.0. However, the DBT is performed in
Ver.1.5.
Sentence Information Sentence Information
DBT Depth from the transducer MWV Wind Direction, Wind Speed
DPT Depth from the transducer, RMC Latitude/Longitude, Course,
Draft Ground Speed, Date
GGA Latitude/Longitude, Time TLL Target Position
GLL Latitude/Longitude VHW Water Speed
HDT Heading VTG Course, Ground Speed
MTW Water Temperature ZDA Date,Time
0093132702-10 5-11
- This page intentionally left blank.-
CVS-126 Chapter 6 Table Attached
[Disp] key
Disp NAV1, Normal (H), Zoom (H), Dual freq, Zoom (L), Normal (L), NAV2
[▲RANGE▼] key
RANGE Auto range, 5.0, 10.0, 20.0, 50.0, 100, 160, 300, 500, Auto shift
[GAIN]
[BRILL] key
LCD brill 1 to 10: 10
Panel brill 1 to 10: 10
[EVENT] key
Store pos, Store image, Fishing hot spot
[FUNC] key
Image speed, IR, Color rejection, Noise rejection, Shift, Zoom range,
Zoom start, A scope, White line, Background color, Disp width,
NAV start, NAV1, NAV2, Image swap, Image recall, Sona-tone
0093132702-10 6-1
Chapter 6 Table Attached CVS-126
[MENU] key
Adjust Image speed (Speed1, Speed2, Speed3, Speed4, Stop, Speed5 (1/1), Speed6,
Speed7, Speed8, Speed9)
IR (OFF, Weak, Strong)
Color rejection (0 to 50 %: 0%)
Noise rejection (0 to 10: 0)
TVG (Weak, Medium, Strong)
TX power (20, 30, 40, 50, 60, 70, 80, 90, 100, Auto)
Gain (TD) (-50 to 50) Inner-hull : No Inner-hull : Yes
H: 0, L: 0 H: 15, L: 40
6-2 0093132702-10
CVS-126 Chapter 6 Table Attached
System EVENT key set (Store pos, Store image, Fishing hot spot)
FUNC key set (Image speed, IR, Color rejection, Noise rejection, Shift, Zoom range,
Zoom start, A scope, White line, Background color, Disp width,
NAV start, NAV 1, NAV 2, Image swap, Image recall, Sona-ton)
0093132702-10 6-3
Chapter 6 Table Attached CVS-126
6-4 0093132702-10
CVS-126 Chapter 6 Table Attached
6.2 Specification
0093132702-10 6-5
Chapter 6 Table Attached CVS-126
6.3 Appearance
Plane view
Unit: mm (inch)
6-6 0093132702-10
CVS-126 Chapter 6 Table Attached
Unit: mm (inch)
Unit: mm (inch)
0093132702-10 6-7