You are on page 1of 6

Booting `IOSv: flash0:vios_l2-adventerprisek9-m (hd0,msdos1)'

Booted IOSv. Boot args: [/vios_l2-adventerprisek9-m]

Smart Init is enabled

Restricted Rights Legend

Use, duplication, or disclosure by the Government is


subject to restrictions as set forth in subparagraph
(c) of the Commercial Computer Software - Restricted
Rights clause at FAR sec. 52.227-19 and subparagraph
(c) (1) (ii) of the Rights in Technical Data and Computer
Software clause at DFARS sec. 252.227-7013.

cisco Systems, Inc.


170 West Tasman Drive
San Jose, California 95134-1706

Cisco IOS Software, vios_l2 Software (vios_l2-ADVENTERPRISEK9-M), Experimental


Version 15.2(20200924:215240) [sweickge-sep24-2020-l2iol-release 135]
Copyright (c) 1986-2020 by Cisco Systems, Inc.
Compiled Tue 29-Sep-20 11:53 by sweickge

This product contains cryptographic features and is subject to United


States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.

A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html

If you require further assistance please contact us by sending email to


export@cisco.com.

Cisco IOSv () processor (revision 1.0) with 574709K/209920K bytes of memory.


Processor board ID 953SUUWZ34F
16 Gigabit Ethernet interfaces
DRAM configuration is 72 bits wide with parity disabled.
256K bytes of non-volatile configuration memory.
0K bytes of ATA System CompactFlash 0 (Read/Write)
0K bytes of ATA CompactFlash 1 (Read/Write)
0K bytes of ATA CompactFlash 2 (Read/Write)
0K bytes of ATA CompactFlash 3 (Read/Write)

Press RETURN to get started!

*Mar 1 00:00:01.967: %ATA-6-DEV_FOUND: device 0x1F0


*Mar 1 00:00:02.053: %NVRAM-5-CONFIG_NVRAM_READ_OK: NVRAM configuration
'flash:/nvram' was read from disk.
*Sep 22 11:20:18.706: %SPANTREE-5-EXTENDED_SYSID: Extended SysId enabled for type
vlan
*Sep 22 11:20:22.424: %LINK-5-CHANGED: Interface GigabitEthernet0/0, changed state
to reset
*Sep 22 11:20:22.424: %LINK-5-CHANGED: Interface GigabitEthernet0/1, changed state
to reset
*Sep 22 11:20:22.425: %LINK-5-CHANGED: Interface GigabitEthernet0/2, changed state
to reset
*Sep 22 11:20:22.425: %LINK-5-CHANGED: Interface GigabitEthernet0/3, changed state
to reset
*Sep 22 11:20:22.425: %LINK-5-CHANGED: Interface GigabitEthernet1/0, changed state
to reset
*Sep 22 11:20:22.426: %LINK-5-CHANGED: Interface GigabitEthernet1/1, changed state
to reset
*Sep 22 11:20:22.426: %LINK-5-CHANGED: Interface GigabitEthernet1/2, changed state
to reset
*Sep 22 11:20:22.581: %PARSER-4-BADCFG: Unexpected end of configuration file.

*Sep 22 11:20:22.948: %SYS-5-CONFIG_I: Configured from memory by console


*Sep 22 11:20:23.554: %LINEPROTO-5-UPDOWN: Line protocol on Interface
GigabitEthernet0/0, changed state to up
*Sep 22 11:20:23.555: %LINEPROTO-5-UPDOWN: Line protocol on Interface
GigabitEthernet0/1, changed state to down
*Sep 22 11:20:23.555: %LINEPROTO-5-UPDOWN: Line protocol on Interface
GigabitEthernet0/2, changed state to up
*Sep 22 11:20:23.555: %LINEPROTO-5-UPDOWN: Line protocol on Interface
GigabitEthernet0/3, changed state to up
*Sep 22 11:20:23.556: %LINEPROTO-5-UPDOWN: Line protocol on Interface
GigabitEthernet1/0, changed state to up
*Sep 22 11:20:23.556: %LINEPROTO-5-UPDOWN: Line protocol on Interface
GigabitEthernet1/1, changed state to up
*Sep 22 11:20:23.557: %LINEPROTO-5-UPDOWN: Line protocol on Interface
GigabitEthernet1/2, changed state to up
*Sep 22 11:20:23.557: %LINEPROTO-5-UPDOWN: Line protocol on Interface
GigabitEthernet1/3, changed state to up
*Sep 22 11:20:24.685: %LINK-3-UPDOWN: Interface GigabitEthernet3/3, changed state
to down
*Sep 22 11:20:24.686: %LINK-3-UPDOWN: Interface GigabitEthernet3/2, changed state
to down
*Sep 22 11:20:24.686: %LINK-5-CHANGED: Interface GigabitEthernet3/1, changed state
to administratively down
*Sep 22 11:20:24.687: %LINK-5-CHANGED: Interface GigabitEthernet3/0, changed state
to administratively down
*Sep 22 11:20:24.687: %LINK-5-CHANGED: Interface GigabitEthernet2/3, changed state
to administratively down
*Sep 22 11:20:24.688: %LINK-5-CHANGED: Interface GigabitEthernet2/2, changed state
to administratively down
*Sep 22 11:20:24.688: %LINK-5-CHANGED: Interface GigabitEthernet2/1, changed state
to administratively down
*Sep 22 11:20:24.689: %LINK-5-CHANGED: Interface GigabitEthernet2/0, changed state
to administratively down
*Sep 22 11:20:24.689: %LINK-3-UPDOWN: Interface GigabitEthernet1/3, changed state
to down
*Sep 22 11:20:24.690: %LINK-3-UPDOWN: Interface GigabitEthernet1/2, changed state
to down
*Sep 22 11:20:24.690: %LINK-3-UPDOWN: Interface GigabitEthernet1/1, changed state
to down
*Sep 22 11:20:24.691: %LINK-3-UPDOWN: Interface GigabitEthernet1/0, changed state
to down
*Sep 22 11:20:24.691: %LINK-3-UPDOWN: Interface GigabitEthernet0/3, changed state
to up
*Sep 22 11:20:24.693: %LINK-3-UPDOWN: Interface GigabitEthernet0/2, changed state
to down
*Sep 22 11:20:24.693: %LINK-5-CHANGED: Interface GigabitEthernet0/1, changed state
to administratively down
*Sep 22 11:20:24.694: %LINK-3-UPDOWN: Interface GigabitEthernet0/0, changed state
to up
*Sep 22 11:20:25.705: %LINEPROTO-5-UPDOWN: Line protocol on Interface
GigabitEthernet3/3, changed state to down
*Sep 22 11:20:25.705: %LINEPROTO-5-UPDOWN: Line protocol on Interface
GigabitEthernet3/2, changed state to down
*Sep 22 11:20:25.706: %LINEPROTO-5-UPDOWN: Line protocol on Interface
GigabitEthernet1/3, changed state to down
*Sep 22 11:20:25.706: %LINEPROTO-5-UPDOWN: Line protocol on Interface
GigabitEthernet1/2, changed state to down
*Sep 22 11:20:25.707: %LINEPROTO-5-UPDOWN: Line protocol on Interface
GigabitEthernet1/1, changed state to down
*Sep 22 11:20:25.707: %LINEPROTO-5-UPDOWN: Line protocol on Interface
GigabitEthernet1/0, changed state to down
*Sep 22 11:20:25.708: %LINEPROTO-5-UPDOWN: Line protocol on Interface
GigabitEthernet0/2, changed state to down
*Sep 22 11:20:28.352: %SYS-5-RESTART: System restarted --
Cisco IOS Software, vios_l2 Software (vios_l2-ADVENTERPRISEK9-M), Experimental
Version 15.2(20200924:215240) [sweickge-sep24-2020-l2iol-release 135]
Copyright (c) 1986-2020 by Cisco Systems, Inc.
Compiled Tue 29-Sep-20 11:53 by sweickge
*Sep 22 11:20:28.380: %PNP-6-PNP_DISCOVERY_STOPPED: PnP Discovery stopped (Startup
Config Present)% Generating 1024 bit RSA keys, keys will be non-exportable...
[OK] (elapsed time was 1 seconds)
Failed to generate persistent self-signed certificate.
Secure server will use temporary self-signed certificate.

*Sep 22 11:21:34.730: %PLATFORM-5-SIGNATURE_VERIFIED: Image 'flash0:/vios_l2-


adventerprisek9-m' passed code signing verification
*Sep 22 11:21:35.174: %SSH-5-ENABLED: SSH 1.99 has been enabled
IOSv - Cisco Systems Confidential -

Supplemental End User License Restrictions

This IOSv software is provided AS-IS without warranty of any kind. Under no
circumstances may this software be used separate from the Cisco Modeling Labs
Software that this software was provided with, or deployed or used as part of a
production environment.

By using the software, you agree to abide by the terms and conditions of the Cisco
End User License Agreement at http://www.cisco.com/go/eula. Unauthorized use or
distribution of this software is expressly prohibited.

Sw-1>en
Sw-1#sh run
Building configuration...

Current configuration : 3520 bytes


!
! Last configuration change at 11:20:33 UTC Fri Sep 22 2023
!
version 15.2
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
service compress-config
!
hostname Sw-1
!
boot-start-marker
boot-end-marker
!
!
!
no aaa new-model
!
!
!
!
!
!
!
!
no ip domain-lookup
ip cef
no ipv6 cef
!
!
!
spanning-tree mode pvst
spanning-tree extend system-id
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
interface GigabitEthernet0/0
switchport access vlan 13
switchport mode access
negotiation auto
spanning-tree portfast edge
!
interface GigabitEthernet0/1
shutdown
negotiation auto
!
interface GigabitEthernet0/2
negotiation auto
!
interface GigabitEthernet0/3
switchport access vlan 13
switchport mode access
negotiation auto
spanning-tree portfast edge
!
interface GigabitEthernet1/0
negotiation auto
!
interface GigabitEthernet1/1
negotiation auto
!
interface GigabitEthernet1/2
negotiation auto
!
interface GigabitEthernet1/3
negotiation auto
!
interface GigabitEthernet2/0
shutdown
negotiation auto
!
interface GigabitEthernet2/1
shutdown
negotiation auto
!
interface GigabitEthernet2/2
shutdown
negotiation auto
!
interface GigabitEthernet2/3
shutdown
negotiation auto
!
interface GigabitEthernet3/0
shutdown
negotiation auto
!
interface GigabitEthernet3/1
shutdown
negotiation auto
!
interface GigabitEthernet3/2
negotiation auto
!
interface GigabitEthernet3/3
negotiation auto
!
ip forward-protocol nd
!
ip http server
ip http secure-server
!
ip ssh server algorithm encryption aes128-ctr aes192-ctr aes256-ctr
ip ssh client algorithm encryption aes128-ctr aes192-ctr aes256-ctr
!
!
!
!
!
!
control-plane
!
banner exec ^C
IOSv - Cisco Systems Confidential -

Supplemental End User License Restrictions

This IOSv software is provided AS-IS without warranty of any kind. Under no
circumstances may this software be used separate from the Cisco Modeling Labs
Software that this software was provided with, or deployed or used as part of a
production environment.

By using the software, you agree to abide by the terms and conditions of the Cisco
End User License Agreement at http://www.cisco.com/go/eula. Unauthorized use or
distribution of this software is expressly prohibited.
^C
banner incoming ^C
IOSv - Cisco Systems Confidential -

Supplemental End User License Restrictions

This IOSv software is provided AS-IS without warranty of any kind. Under no
circumstances may this software be used separate from the Cisco Modeling Labs
Software that this software was provided with, or deployed or used as part of a
production environment.

By using the software, you agree to abide by the terms and conditions of the Cisco
End User License Agreement at http://www.cisco.com/go/eula. Unauthorized use or
distribution of this software is expressly prohibited.
^C
banner login ^C
IOSv - Cisco Systems Confidential -

Supplemental End User License Restrictions

This IOSv software is provided AS-IS without warranty of any kind. Under no
circumstances may this software be used separate from the Cisco Modeling Labs
Software that this software was provided with, or deployed or used as part of a
production environment.

By using the software, you agree to abide by the terms and conditions of the Cisco
End User License Agreement at http://www.cisco.com/go/eula. Unauthorized use or
distribution of this software is expressly prohibited.
^C
!
line con 0
logging synchronous
line aux 0
line vty 0 4
password ine
login
transport input telnet
!
!
end

Sw-1#

You might also like