Professional Documents
Culture Documents
A15Owner's Manual05.2
A15Owner's Manual05.2
-1-
Contents
Central control door lock system........................9
Chapter 1 Brief Introduction 1 Safety lock for children use ............................. 10
Safety protection ...............................................2 Front seat sliding adjustment ........................... 11
Environmental protection ..................................2 Adjustment of front seat angle ......................... 11
Regulations of break-in period for new vehicle...3 Head restraints ................................................ 11
Matters needing attention during new car break-in Folding the rear seat backrest........................... 12
period: ..............................................................3 Safety belt precautions .................................... 13
Explanation on Regular Reminder Indicators of Protection of safety belt................................... 15
Motor Vehicle ...................................................5 Pregnant woman..............................................15
Chapter 2 The Need-to-Know before Driving 7 Child restraint system......................................16
Keys .................................................................8 Three-point type seat belt ................................16
Using the seat belts..........................................17
Power window switch......................................18
Glass forbidden switch .................................... 19
Outside rearview mirror................................... 20
Inside rearview mirror .....................................21
.................8 Safty airbag..................................................... 21
Door lock..........................................................8 Airbag for the driver........................................ 23
-1-
Brief Indroduction
Front passenger airbag..................................... 23 Stand-by power supply interface ......................36
Engine compartment hood ...............................24 Rear armrest box / cup holder .......................... 36
Open trunk lid.................................................25 Chapter 4 Starting up and Operating 38
Chapter 3 Operation and Adjustment of Fuel ................................................................ 39
Equipment inside Vehicle 28 Ignition switch ................................................ 39
Adjustment of steering wheel...........................29 Before starting the engine ................................40
Horn button Sun visor .....................................29 Turn engine on/off........................................... 41
Sun visor......................................................... 29 Warming the engine up.................................... 42
Vanity mirror...................................................30 Operation of automatic transmisssion............... 42
Auxilary handle............................................... 30 Operation of hand brake ..................................43
Interior light....................................................31 Braking system ............................................... 44
Rear ceiling lamp ............................................ 32 Operation guide...............................................44
Front cup holder..............................................32 Brake servo unit ..............................................46
Front ashtray...................................................33 Brake fluid...................................................... 46
Cigarette lighter ..............................................33 Check brake fluid level.................................... 46
Front armrest box ............................................ 34 Replacement of brake fluid.............................. 47
Glove box ....................................................... 35 Parking ........................................................... 47
Rear ashtray....................................................35 Anti-lock brake system (ABS) .........................48
-2-
Contents
Braking with anti-lock brake system ................ 49 Generator warning light...................................60
ABS self check................................................ 49 Safety belt warning light..................................61
Steering system ............................................... 50 Safety airbag warning light.............................. 61
Driving through water .....................................50 Turn signal warning light/danger warning light 61
Ternary catalytic converter...............................51 High beam indicator light ................................62
How to save fuel and make your vehicle last Front fog light/rear fog light switch.................. 62
longer, too? ..................................................... 51 Turn signal lamp switch................................... 63
Chapter 5 Instruments and Controls 53 Headlight switch ............................................. 63
Warning lights system .....................................55 High beam switch............................................64
Speedometer ...................................................55 Meeting lamp switch ....................................... 64
Odometer........................................................ 55 Windshield wiper switch..................................64
Engine coolant temperature gauge.................... 56 Windshield washer switch ...............................65
Fuel gauge ...................................................... 56 Headlight beam adjustment switch...................66
Fuel warning light ........................................... 57 Danger warning light switch............................66
Engine malfunction indicator light ...................57 Rear Window Defroster Switch........................ 66
Low Oil Pressure Warning Light...................... 58 Digital clock ...................................................67
Brake system warning lamp.............................59 Chapter 6 Ventilation System and Air
ABS warning light........................................... 60 Conditioning System 68
-3-
Brief Indroduction
Control panel ..................................................71 Cassette player ................................................ 85
Ventilation and warm air.................................. 71 CD (Compact Disc).........................................86
Central vent .................................................... 71 Clock setting...................................................87
Bypass vent..................................................... 71 Audio System for Songs (Optional) ...............89
Front wiper defroster /defogger vent ................ 72 Audio panel function (optional) .......................90
Front window defrostter/defogger vent............. 72 Performance....................................................92
Temperature control switch.............................. 72 Overall............................................................ 92
Airblower switch............................................. 73 Case................................................................ 92
Airflow distribution switch.............................. 73 Caring for your cassette player and tape...........92
Internal circulation switch ...............................74 Operation method............................................ 93
A/C switch...................................................... 74 Cassette player operation ................................. 96
A/C system ..................................................... 75 Radio reception ...............................................96
Operating tips.................................................. 78 CD changer mode operation method ................ 98
Chapter 7 Audio System 79 RPT (Repeat) ..................................................99
VDO Audio System ....................................... 80 Random ..........................................................99
VDO Audio Panel Function ............................. 81 Specifications..................................................99
Audio system ..................................................83 Baisc operation of record changer for 6 CD.... 100
Radio.............................................................. 84 Operating guide............................................. 101
-4-
Contents
Specifications................................................ 102 Air filter........................................................ 117
Use of CD..................................................... 102 Spark plug .................................................... 118
Caring for your compact disc player and discs 103 Drive belt...................................................... 119
Error display ................................................. 104 Windshield washer fluid ................................ 120
Trouble-shooting........................................... 105 Wind shield wiper ......................................... 120
Chapter 8 Maintenance and Upkeep 107 Maintenane of battery.................................... 121
Engine compartment...................................... 108 Brake pedal................................................... 122
Maintaining & protective measures................ 109 Clutch pedal.................................................. 122
Safety attention ............................................. 110 Hand brake ................................................... 122
Checking list for the driver ............................ 110 Ternary catalytic converter............................. 122
You should check the engine oil level by the Wheels and tires............................................ 123
following steps.............................................. 111 Tire inflating................................................. 124
Replacement of engine oil and filter............... 113 Tire condition................................................ 125
Coolant level................................................. 114 Exchange of tires........................................... 126
Engine overheating........................................ 114 Ignition system.............................................. 127
Brake fluid.................................................... 115 Central electronics box .................................. 127
Gearbox oil ................................................... 116 Replacement of fuse ...................................... 128
Power steering fluid level .............................. 117 Engine compartment relay/Fuses box............. 128
-5-
Brief Indroduction
Fuse box ....................................................... 129 Chapter 10 In Case of an Emergency 136
Tools in the trunk and spare tire ..................... 137
Replacement of wheel ................................... 137
Procedures of replacement............................. 138
Jump starting the engine ................................ 140
Towing vehicle.............................................. 142
......... 129 Emergency towing ........................................ 142
Front relay box 1........................................... 130 Save yourself after being caught in spongy
Front relay box 2........................................... 130 ground .......................................................... 143
Chapter 9 Car Light 131 Chapter 11 Technical Requirements and Data
Combination headlight (containing low beam 145
light, high beam light/driving light, and front Dimension of vehicle..................................... 147
turning lamp) ................................................ 133 Parameters of engine ..................................... 148
Front/rear fog lamp ....................................... 133 Common technical characters ........................ 149
Brake lamp, the third brake lamp ................... 134 Wheel ........................................................... 149
Reversing lamp /vehicle plate lamp................ 134 Tire pressure ................................................. 150
Rear turn signal lamp .................................... 135 Notice: ...................................................... 150
Side turn signal lamp..................................... 135 You should check the tire pressures at least once a
-6-
Contents
month; tire pressure is especially important while
high-speed driving......................................... 150
Pressure values listed in the schedule are
appliable for cold tire pressure; it is not necessary
to reduce the pressure if the pressure slightly goes
up while tire being heated.............................. 150
Official VIN of vehicle.................................. 151
Engine No..................................................... 151
Vehicle data plate .......................................... 151
-7-
Brief Indroduction
-1-
Brief Indroduction
Don’t touch electrical decrease of noise and
Safety protection components; don’t touch the
high-temperature parts (such as environmental pollution, if you
exhaust system), with the ignition adopt appropriate moment to
The car runs at a high rotational speed on.
upshift.
as well as high-speed, therefore, while
Do not treat the waste fuel
driving, in order to avoid the Environmental protection
container as the domectic garbage,
occurance of danger; you should pay
please have it disposed by your
attention to the following matters. The earth is our living homeland; every local Chery authorized waste
The driver and passengers should one has an unshirkable duty to protect disposal institution.
wear safety belt while driving. the environment. Making use of Engine oil, brake fluid,
Be sure not to drive when drunk. vehicle accurately and putting varies of anti-freeze fluid and tires after
Comply with the traffic abandoned materials to rational having being used, can only be
regulations. disposal are critical moves towards disposed by professional waste
Pay attention to make way for
achiving this aim. disposal institution or you can
pedestrian or other vehicles while
the car door is open. You should avoid that the engine consult your Chery Authorized
Pay attention to avoid being works at unnecessary high
burnt and electrical shocked while Service Station for assistance, and
inspecting the car. For example rotational speed. It is do not treat it as household
(e.g.): Running engine may lead advantageous for economy of fuel,
to injury, scald and electric shock. rubbish or drain it to the public
-2-
Brief Indroduction
drainage system. *Avoid full-speed drive for every gear.
Regulations of break-in period
Battery after having being used Break-in regulations between 1000
contains sulphur and lead. You for new vehicle km and 1500 km:
should not abandon it as common
household rubbish. You should You can speed up gradually while
The friction resistance of every
deliver it to local waste material driving; it is OK for the engine
compononts of the new car is much
disposal station for assistance. working at top speed in a short time.
stronger at the initial stage than that of
Under the circumstance of using normal stage. The future service life,
regulated gasoline, you are reliability and economy of your Matters needing attention
recommended to use high-grade vehicle shall be largely determined by
unleaded gasoline. break-in result of your new car at
during new car break-in
If your car is equipped with ternary initial stage, therefore, you should use
catalytic converter, please inspect it at
period:
your new car in accordance with
regular intervals, according to local regulations of break-in period.
road and your vehicle’s condition, to You are strictly forbidened to step on
Break-in regulations within 1000 km:
avoid overexhaust of waste air. the accelerator, whenever the engine is
* Do not run the engine at full speed.
cold. It is not good for you to speed up
* Do not drive over 100 km/h
the engine suddenly. You should start
-3-
Brief Indroduction
to drive when the coolant temperature influence the normal use of engine. Drive the vehicle safely!
goes up to normal state, otherwise the It is necessary to drive at low speed, Notice: Pay attention to the break-in
engine will be worn at an earlier stage. during the first 100 km. You should period during the first 200 km, after
The acceptable top engine speed in a take special care, for the tires of new replacing brake friction disc, and drive
short time is 4000 r/min. In manual car do not have the best friction force the vehicle safely.
shifting case, you should upshif when for roadway, which will result in brake The wheel nuts should be retightened
the indicating pointer of the force not enough and brake distance after the new car driving 800 km.
tachometer gets into the red zone. And enlarged.
avoid the high-speed running of the Notice: The wheel nuts should be
engine. It is advantageous for economy Notice: Drive the vehicle safely retightened after driving 800 km, if the
of fuel, decrease of engine noise and during the first 100 km after replacing tires have been replaced or the wheel
environmental pollution if you upshift the tires. nuts have been loosened before.
without delay. Brake friction disc of new car does not
It is not necessary for engine speed have the best frictional force; therefore
being too low, while normally driving. it also needs break-in period. You
It is easy for the engine to accumlate should drive cautiously during the first
Carbon if the engine speed is too low 200 km; heavily apply the brake pedal
frequently, and furthermore it will with the parking brake depressed.
-4-
Brief Indroduction
Explanation on Regular Reminder Indicators of Motor Vehicle
-7-
The Need-to-Know before Driving
-8-
The Need-to-Know before Driving
-9-
The Need-to-Know before Driving
- 10 -
The Need-to-Know before Driving
- 11 -
The Need-to-Know before Driving
Folding procedures:
Notice ·Lift the seat cushion up; move
Head restraint protects your head and
forward slightly, it is ok to raise the
neck from being injured, in the event
of a collision, therefore, adjust it cushion from the rear.
properly before driving.Adjust the top
of the head restraint, so that it is
closest to the top of your ears.After
adjusting the head restraint, make sure Notice
it is locked in proper position, before For your safety, adjust the head
driving. restraint before driving, make sure it is
in proper position, and do not
disassemble it at will.
Disassemble the head restraint:
·Pull the damping cushion up to the
- 12 -
The Need-to-Know before Driving
- 13 -
The Need-to-Know before Driving
belts provided.Use the belt for only belt privately,do not attach any driving.Do not wear safety belt if it is
equipment which will influence the twisted, make it smooth before use, or
one person at a time.Do not use a operation of safety belt.Damaged contact your Chery Authorized Service
single belt for two or more people, safety belt could not be used once Station for assistance, excellent
more,replace it immediately,because it technical personnel of Chery will help
even children.It is not suitable for child maybe hurt you.Avoid safety belt you to solve these problems. Do not
under 6 years old to use safety system being squeezed to damage by fasten diagonal seat belt under your
door and seat. arm,you should fasten it in the middle
belt.Child’s seat or auxiliary cushion of your chest,the belt should be kept
should be installed for child to use. away from your neck.You should wear
While using the safety belt: the seat belt securely, and as low as
In order to lower the chance of injury, possible over the hips and not on the
Notice: waist.You will be sliding under the
The passengers may be hurt because of in the event of emergency braking or a safety belt if the safety belt is
inertia in the event of emergency excessive loose,the risk of personal
braking or a collision, so you should collision, please use and maintain
injury and death may increase.Button
use safety belt whenever you are safety belt and child restraint system of buckle should be placed
driving.Do not use a single belt for two outward,insert the tab into the
or more people simultaneously.Do not according to accurate method.
buckle.Do not insert anything in the
hold hardware or breakables in clothes safety belt revet plate opening, in order
keeping close to safety belt, especially Notice: to avoid safety belt being pinched,if
gas lighter if gas lighter explode Failure to wear safety belt correctly pinched,you have no choice but wrap
during process of squeezing, severe could result in personal injury even all the belt to the reel,then take out
accident maybe take place.Failure to death.Place backrest of seat upright as requested length accordingly (This
use safety belt correctly could lead to possible as you can.Avoid reclining the work should be performed by Chery
severe injury.Do not reequip safety seatback any more than needed while Authorized Service Station).Please do
- 14 -
The Need-to-Know before Driving
not disassemble or modify the safety replace the damaged components as stained or used improperly.
belt system privately. .The entire assembly used in a severe
soon as possible.Over tensioned safety impact should be replaced, even if
belt in accident must be replaced, damage is not obvious.If the safety belt
Protection of safety belt is not suitable,it may be lead to more
Chery recommends to replace the belt severe injury.Do not disassemble or
assembly, if it has been used in a modify the safety belt at will.
Keep the belts always clean and severe impact.You should check the
dry.Aviod safety belt being stained by belt assembly to see if they need Pregnant woman
polishing compound,oil and replacing, even if they has not been
chemicals,especially acid fluid of used in accident,but there is something Chery suggests that the pregnant
battery.If the belts need cleaning, use a wrong with them. woman should ask her doctor for
mild soap solution or lukewarm
specific recommendations before using
water.Never use bleach, dye, or Notice:
Damaged safety belt will lose a seat belt.
abrasive cleaners- they may severely protective function without
weaken the belts, result in hidden replacement. You had better inspect the Notice:
belt assembly at regular intervals. The pregnant woman and unborn baby
trouble of safety.You should avoid Please contact your Chery Authorized may be hurt during trip.Therefore: If
safety belt touching sharp Service Station for seat belt inspection possible, please use three-point type
and replacement, according to the diagonal lapping safety belt (please
objects.Check to see if the safety belt request, after a collision. Replace belt consult your doctor).
is damaged ,at regular intervals, assembly if it has been damaged,
- 15 -
The Need-to-Know before Driving
secured in a rear seat, using a child properly secured in a rear seat, using
Child restraint system
restraint system.Do not use a rear the seat belt.You had better not let the
–facing child restraint system in the child use diagnal type seat belt if
You should use suitable child restraint
front seat, because the force of the possible.If the child use diagonal type
system if you carry baby or child.
rapid inflation of the passenger airbag seat belt, the seat belt is close to the
We recommend that you should choose
may cause severe injury to the child. child’s face or neck, please let the
suitable child type seat installed in
child in centre position, that is to say
vehicle, in accordance with concrete
Notice the inside position of seat belt.
weight and height of the child.
Always read the manufacturer’s
Accident statistic material indicates
instructions, before installing child Three-point type seat belt
that it is safer to install children
restraint system.
restraint system in the rear seat, than
·Fasten it with seat belt or take it away
the front seat, so we recommed you Chery vehicles are all equiped with
from the vehicle if you do not use it.
had better install the child restraint three-point type seat belt with brake
· Do not hold a child in your arms
system in the rear seat. limiter.Though adjustable seat belt is
while driving.
always next to your body, your body
Notice If a child is too big to use a child
can move freely while steady driving.
Baby or little child should be properly restraint system, the child should be
- 16 -
The Need-to-Know before Driving
- 17 -
The Need-to-Know before Driving
Adjustment of seat belt altitude: move the tab to the suitable position,
Notice
You can slide the adjustable anchor up fasten your belt. Failure to use seat belt correctly could
and down, to adjust the seat belt If the belt is not short enough for you, increase the chance of severe
injury.The belt should be kept away
altitude. move the tab to the suitable position, from your belly, keep the lap belt as
fasten your belt. low on your hip bone as possible.It
Notice maybe result in severe injury if the
For your safety,do not place the seat Press the lap buckle-release button and seat belt is damaged or too tight.Do
belt too high or too low,it will tie your allow the belt to retract, if you want to not work hard to insert unsuitable tab
neck if the seat belt is too high,it will into the buckle.Insert the tab into the
move under your shoulder if it is too release the seat belt.The tab and buckle buckle properly, in order to provide
low,for your safety,please adjust the of rear seat belt is marked with maximum protection of the seat belt
seat belt to suitable position. system, please put seat belt to the
CENTRE.Please check the mark original positon after disassembling
before you wear the seat belt. the rear seat.
Lapping the seat belt
If the belt is not long enough for you, can operate the power windows
- 18 -
The Need-to-Know before Driving
through the switch.Push the button If the switch is locked, only the driver
down if you want to open the can control window glass elevation,
window .Pull the switch up if you want window glass of the passenger side
to close the window.Release the switch and rear row are all no longer have any
when the window moves in the effect.
requested position.
Notice
·Make sure to turn off the ignition key
in order to avoid unnecessary injury to
the child, while you leave the vehicle.
Glass forbidden switch
Release the button when the window
fully closed,in order to avoid electric
motor damage. This switch is mounted in the driver’s
·Keep your hand, head or other objects side armrest, push it down (yellow) if
inside the window.
·Do not let the child play with power you want to lock it, push it once more
window switch, for power window if you want to return to Free State
unexpectedly close will result in
severe injury. (green).
- 19 -
The Need-to-Know before Driving
- 20 -
The Need-to-Know before Driving
ensure driving safely,please see the There are two positions of day and Notice
back field of vision with outside
night.Place the lever at “day” position In order to keep rear version range of
rearview mirror and inside rearview
the driver.You can select daylight
mirror simultaneously. while daylight driving,place the lever position and carry out adjustment in
at “night” position while night order to get the best version.It is
possible to weaken the clarity of
driving,so as to reduce glare from the rearview mirror and limit the version
headlights of the vehicle behind you range, if you select night position.
- 21 -
The Need-to-Know before Driving
In a severe frontal collision or collision not necessary for the airbag to activate, personal injury, do not modify
from the side, the airbags inflate, they because the vehicle has already borne components of airbag system.It is very
produce fairly loud noise and release the large amount of impact force.In dangerous to modify, remove or open
some smoke, and the smoke is not other accidents, when severe collision the safety airbag without permission,
harmful.When severe collision occurs, occurs, such as chasis collision, it is doing so may cause personal
injury even death maybe occur even if not in a large scale that the chasis injury.You should have the airbag
you wear seat belts, even if the maybe damaged, but it maybe result in disposed and replaced by Chery
deployment of airbag is normal, so it is airbag explosion. Authorized Service Station.Do not put
very important for you to be careful to objects on or in front of the dashboard
Notice:
drive and pay attention to the safety! or steering wheel pad that houses the
For the safety of all occupants, be sure
In case of a severe collision, there is no airbag system, they might restrict
to always wear seat belts.The SRS
system can provide overall protect inflation or cause personal injury.
airbag system is designed only as a
-ion.After collision, it is impossible for The airbag will not work under the
supplement to the primary protection
you to see whether or not the airbag following conditions:
of seat belt systems of the driver and
has inflated with your eyes.In accident Two vehicles collide with other each,
front passenger. Do not remove
which airbag doesn’t inflat, the vehicle impact from the side, vehicle roll-over
components of airbag without
body is overdamaged, that means it is and not enough impact force.
permission, doing this may cause
- 22 -
The Need-to-Know before Driving
- 23 -
The Need-to-Know before Driving
- 24 -
The Need-to-Know before Driving
4. Take the supporting lever out, before operate the open handle of engine while checking the bottom of engine
closing the engine hood, press the the hood while driving, because not only compartment hood: Put the
spacer, in order to avoid vibriation of the driver’s field of version will be transmission to neutral gear, pull up
supporting lever and producing noise. influenced, but also windshield the parking brake. When the engine is
5. Let the engine hood be falling freely window glass maybe crashed to be running,running components of engine
from 30 cm (1feet) high,close the broken, if the engine hood is will be uncovered if you open the
engine hood,finally pull up edge of unexpected opened while high-speed engine compartment hood, do not wear
engine compartment hood,to make driving, resulting in personal injury.Do loose clothing,keep hands and hair
sure that the engine hood is locked not drive the vehicle while the engine away from the running parts and
properly. hood is open,because the vehicle exhaust manifold, for the
maybe move from the static state with high-temperature parts maybe cause
Notice the engine hood open.Be sure that the unnecessary personal injury.
While driving, do not open the engine ignition key is taken off,put the
compartment hood .Before driving, transmission to gear 1 or reverse gear Open trunk lid
pull the hood edge, check it to see and make the parking brake ready for
whether or not the engine compartment use.When the engine is running,pay
hood is completely locked.Do not attention to the following matters
- 25 -
The Need-to-Know before Driving
Insert the key to trunk key hole,the vehicle with the trunk lid open.
Open
Lock trunk lid will be opened if you turn the Fuel filler port is located in right side
key counter-clockwise,the trunk lid wing of the vehicle.
Notice
While driving, it maybe blocks the
driver’s field of version if the trunk lid
is opens, increasing the possibility of
incident.Therefore: Do not drive the
- 26 -
The Need-to-Know before Driving
Unlock the interior cap of fuel tank clockwise if you want to open the fuel paint surface, please wash the paint
with vehicle key. trunk cap, turn it clockwise if you want surface with cold water as soon as
to close the fuel trunk cap. possible, if the paint surface is
4. After refueling, turn the fuel tank spattered with gasoline.Fuel in fuel
cap clockwise, tighten it (until you
hear a click), then close the fuel filler tank maybe in compression condition,
cap. you should turn the fuel tank cap
slowly, then completely unscrew the
Notice
fuel tank until there is no “hissing”
Fuel fumes are inflammable, turn off
sound. It is impossible for you to open
the engine while refueling, do not
the fuel refueling cap in cold weather,
smoke, keep away from fire and
Pay attention to the following matters pushing or knocking the refueling cap
spark,do not use microwave
while refueling: slightly will be helpful for you to open
communication tools (such as mobile
1. Turn off the engine. it, because there maybe remaining fuel
phone) , in order to avoid fire disaster.
2. Push down the front side of fuel in the fuel tank,total amount of fuel
Do not apply leaded gasoline to
tank cap, shown as the illustrations; it every time you refill should be lower
unleaded gasoline vehicle, in order to
is ok for you to open the tank cap. than the standard capacity.
avoid engine and exhaust system
3. Insert the key; turn it counter
damage.The gasoline will damage the
- 27 -
Operation and Adjustment of Equipment inside Vehicle
- 28 -
Operation and Adjustment of Equipment inside Vehicle
Sun visor
Adjustment of steering wheel Notice: Adjusting steering wheel is
strictly forbidden while driving. You
Sun visor can be rotated up and down,
can drive only after the adjustment is
This equipment is designed according performed and the steering wheel is or can be rotated laterally, protect
to requests from drivers of different locked properly, otherwise it may
dirver and occupants against strong
cause severe traffic accident.
height, bodily form and hobbies. irradiation.
Adjustment: Pull down the sun visor if you want to
Horn button Sun visor
Pull down the adjustment switch, keep the front sunshine away, sun visor
move the steering wheel up and down on the left can be took out of the fixed
to suitable position, then pulll up the Horn button on both sides of the steering
clamp buckle on the right of the sun
switch to “lock” position, shake the wheel, wherever the ignition switch is,
visor.Rotate to left side glass regarding
steering wheel to see if it is locked the horn can bark.
the left axle as the center, in order to
properly. keep left side sunshine away.
It is ok for you to buckle the sun visor
and straighten it up while taking the
sun visor back.
- 29 -
Operation and Adjustment of Equipment inside Vehicle
Vanity mirror
Auxilary handle
The vanity mirror is mounted on the
back of right side sun visor. Auxilary handle is mounted on the
The right side sun visor has same upper position of right front door and
function and operation methods as the back row door, it make things
left one but not like the left one, the convenient for the passengers.
right sun visor is mounted with vanity
mirror.The vanity light comes on when
you open the cover, providing you
with illumination.
- 30 -
Operation and Adjustment of Equipment inside Vehicle
Interior light
Passenger’s reading light is on the
Door control
Open right:
lamp
In order to make things convenient for
the passenger, passenger’s reading
light is installed, press to the left if you
want to turn it on, press to the right if
Open
you want to turn it off.
- 31 -
Operation and Adjustment of Equipment inside Vehicle
Shown as the illustration, push the
Rear ceiling lamp Front cup holder
outer cover of cup holder, you can
open it.
In order to make things convenient for The cup holder is mounted on the front
rear row passengers, rear personal light controls panel; it is designed for
are designed, it is the door light holding cups fit snugly in its holes.
simultaneously.If you press the “door” Notice:
button, the light will be on if the door If the lid is forcibly pulled up, the
is open; the light will be off if the door drink may spill over the seat occupants,
is closed.If you press the “open” so do not leave the cup lid open, while
button, the light will be always on, driving.
therefore, we recommend you press
the “door” button.
Push it in completely, you can close it.
Operation:
- 32 -
Operation and Adjustment of Equipment inside Vehicle
it open completely, shown as the Notice:
Front ashtray
illustrations.To remove the ashtray, Do not touch the heating wire of the
pull the ashtray upward.Install the cigarette lighter for it may be catching
ashtray in reverse orders. fire while the lighter is heated.Do not
let children play with the lighter.Do
not depress the lighter by hand.Do not
regard the lighter slot as power supply
socket ,otherwise it will increase the
Front ashtray is mounted under the
chance of damage or electrical
front control panel. To use the
appliance circuit malfunction.
ashtray, push the outer cover.
Cigarette lighter
- 33 -
Operation and Adjustment of Equipment inside Vehicle
Notice
The handrail box doesn’t have reliable
locking system, therefore, please do
- 34 -
Operation and Adjustment of Equipment inside Vehicle
not leave the valuables in it.Make sure To close: Close the glovebox shown as ashtray, pull the switch backward,
to lock the door and take the valuables the illustration.
all with you while you leave the Notice: shown as the illustration.
vehicle. Glovebox has no reliable locking
mechanism, therefore never leave
Switch anything valuable inside the
Glove box glovebox.You should always carry the
valuables with you when leaving the
vehicle; meanwhile, you should lock
the door.
- 35 -
Operation and Adjustment of Equipment inside Vehicle
Notice
Stand-by power supply
This power interface only supports
interface D.C. electrical appliance of 12V
(Power 120 W), please check the rated
voltage and power of the electrical
appliance which you want to join up,
in order to avoid dangerous accident. Shown as the illustration, push on the
lid if you want to open the armrest box,
Rear armrest box / cup holder there is a rear cup holder, and you can
accommodate small and light objects
in it.
Stand-by power supply interface is There is a hidden rear armrest box
used for inserting electrical equipment between the rear seats, shown as the
of other vehicles.It is ok to insert the illustration, pull down it if you want to
Switch
plug of electrical appliance after use the armrest.
uncovering the interface,please cover it
after use.
- 36 -
Operation and Adjustment of Equipment inside Vehicle
vehicle,take the valuables all with you
and lock the door.If the lid is forcibly
pulled up,the drink may spill over the
seat occupants,so do not leave the cup
lid open while driving.
Notice
The armrest box has no reliable
locking device,please let it return to its
original position, if you leave the
- 37 -
Starting up and Operating
- 38 -
Starting up and Operating
accidentally, leaded gasoline filler tube container, eapecially if you use
should not be inserted into unleaded
Fuel gasoline filler port. It is impossible for non-professinal refueling equipment.
Chery to use fuel containing methyl Under certain pressure, while fuel is
alcohol (ethyl alcohol). The vehicle
performance will be not good and fuel flowing, if the hose (especially plastic
Select premium gasoline with a
system elements will be damaged, if hose), which is mounted on fuel
Research Octane Number of 93 or you use this kind of fuel. Fuel system
damage and performance problems are distribution pump does not connect the
higher for optimum engine
not covered by Chery’s new vehicle very ground; it is possible to generate
performance. Engine damage caused warranty.
large amount of static electricity.
by use of improper fuels is not covered If you drive your Chery in other
Grounding pump and pipe are
under Chery’s new vehicle warranty. countries, be sure to pay attention to
recommended. In the case of
Make sure to select premium gasoline the following matters:
non-professional fuel filler operation,
with a Research Octane Number of 93. ·Comply with relevant laws and safety
fuel container should be connected to
regulations.
Notice: ground appropriately, too.
·Confirm the availability of the correct
Do not select leaded gasoline for
unleaded gasoline vehicle in order to fuel.
avoid engine and exhaust system Ignition switch
In order to ensure safety, fuel pump
damage. Damage caused by use of
improper fuels is not covered by and pipe must be connected to ground,
Chery’s new vehicle warranty. In order
while refueling with fuel drum or fuel Steering wheel lock hole position:
to avoid filling leaded gasoline
- 39 -
Starting up and Operating
Position 1-Turn off the ignition switch turn the steering wheel slightly, in key to position 2.
and the steering wheel is locked. order to relax the locking mechanism
In order to lock the steering wheel, of steering wheel.
please turn the steering wheel pull out
the key, until you hear a click.The Position 3- Start the engine
radio and horn no longer work in this When the lock hole is in this position,
position. front headlight and electric appliance
with heavy power consumption are all
Notice cut off.
Do not pull out the key before parking Anti-repeat starting device is installed
the vehicle properly, in order to avoid in the ignition switch.This device will
locking the steering wheel prevent the starter from Before starting the engine
accidentally. misstarting,once the starter is
running,so as to avoid fly wheels of
1. Make sure that all occupants fasten
Position 2-Complete the ignition starter and engine being damaged.If
seat belts properly.
electric circuit. you fail to start the engine,please let
2. Turn off unnecessary lights and
If it is hard or impossible for you to the ignition key return to position 1
accessories.
turn the key to this position, you can before restarting,then turn the ignition
- 40 -
Starting up and Operating
3. Make sure pulling hand brake up. checked every time, such as: position,restart it after 10 seconds.
4. Check warning lights of instrument ·Check engine oil level.
2. If the engine can not start within 15
panel to see if they flicker shortly. If ·Check coolant level.
seconds at first time and the
not, please contact your nearest Chery ·Check brake fluid level.
temperature is lower than -12°C, you
Authorized Service Station for service. ·Check power steering fluid level.
should turn the key to “1” position,
5. Lock all doors and trunk lid ·Check windshield washer fluid level. restart it after 10 seconds. Release the
properly. key when the engine starts.
6. Make sure lights and turn signal are
3. For automatic transmission type
in good condition. Turn engine on/off vehicles, after the engine starts, idling
7. Make sure performance of brake is
for several seconds, depress the brake
reliable.
1. Turn the ignition to “3” position pedal, release parking brake; hold it to
8. Make sure fuel is enough.
with your foot off the accelerator pedal. the floor until driving off.
9. Make sure that cleaning degree of
Release it when the engine start,turn
window glass and lampshade glass are 4. For manual transmission type
the key to “2” postion. If the engine
up to the standard. vehicle, make it idling for severval
can not start within 5 seconds at first
10. Make sure tire and tire pressure are
time, the temperature is more than
up to the standard.
-12°C, you should turn the key to “1”
It is not necessary to have some items
- 41 -
Starting up and Operating
engine warm up for a few minutes complicated urban conditions.The
seconds after the engine starts, depress
before driving), and then speed up speed can only be in automatic
the clutch, hold it to the floor until
gradually. elevation gear of 1, 2, 3 and 4.
driving off, and release parking brake.
[2] It is used when engine brake is
5. Release acceleration pedal first needed while driving.When the
Operation of automatic
while stop the car.Turn of ignition
selector lever is in this position,
switch while the engine is idling. transmisssion hydraulic control system can only put
6.You should not turn off the engine through oil way of gear 1 and 2.
immediately, after long-distance Gearchanging handle position [1] It is used only if strong engine
driving at high speed, let the engine function braking is in badly need, this gear is
idling for 1 to 2 minutes, make things [P]Parking, engine starting and key used while driving down or up a hill, it
convenient for the engine temperature removal position can stabilize the vehicle speed
fall gradually. [R] Reverse position effectively. Doing this can avoid
[N] Neutral position frequent gearchanging of automatic
Warming the engine up [D] Normal driving position (gearshift transmission and make the
from gear 1 to gear 4) transmission life last longer.
In cold weather, let the engine idling [3] Driving position while climbing Movement of gearchanging lever
for some time after it starts, (let the up the hill or driving under the position
- 42 -
Starting up and Operating
The gearchanging lever can move from you can drive.While gearchanging,
[P] [R],from [D] [3] [2] [1]and step on the clutch pedal completely,
from[N] [R] [P],only if you press the whole process of gearshift will
the gearchanging limiter button. finish. If it is downshift, after you step
It is not necessary for you to press the on the clutch pedal, shift the lever to
gearchanging limiter button if it move neutral gear, then shift to
from [R] [N] [D] [N]. corresponding low-speed gear, release
Neutral
Notice: While driving, if the the clutch pedal, downshift can be
When you step on the clutch pedal, the lever tightly upward, after parking.
vehicle disconnect the drive between ·With the ignition on, the brake
two shafts, release the clutch, connect warning light will be on if you pull
suitable gear, step on the accelerator,
- 43 -
Starting up and Operating
hand brake up. ·Under any circumstances, clutch pedal
and accelerator should be stepped on
·Pull hand brake lever upward if you
to the full.
want to use hand brake.
·For the above-mentioned reasons,you
· Slightly pull hand brake lever upward,
had better not put pad or other things
push releasing button of lever top
on the pedal surrounding floor,if
down if you want to release hand
indeed necessary,you should be sure
brake.
that the pad will not obstruct
·Hand brake is used for rear wheel movement of the pedals and the pad
Braking system
parking. should not be sliding easily.
·It is easy for you to pull the hand The movement of every pedal should
brake up if you step on brake pedal not have any resistance, so you should Operation guide
while pulling the hand brake up. be sure not to put anything easy to roll
Notice: Be sure to pull hand brake up, over or slide on in that very space. ·New brake gasket can not be in the
before you leave the vehicle. ·Brake pedal travel may be enlarged if best braking condition, until it passes
there is something wrong with the the break-in period.In the first 200km,
- 44 -
Starting up and Operating
good condition, under this brake gasket is rather harsh,for weakened,at this time,you should step
circumstance, you can recover braking frequent starting and parking.So, you on the brake pedal slightly,let brake
effect, only by means of depressing the should be sure to have the disc gasket and brake disc touching
pedal greatly, it is applicable for the checked or replaced by Chery together to generate heat,in order to let
new gasket after replacement. Authorized Service Station, according the moisture evaporate and recover the
to the regulated mileage in the braking performance.
·There may be something wrong with
maintenance manual.
dual return circuit braking system, if ·After driving on road containing salt,
the pedal travel is enlarged ·While driving down the hill, you the salt will be adhensive on surface of
immediately.At this time, the vehicle should make full use of engine braking brake disc or brake gasket, resulting in
can still have braking performance, if performance, downshift when braking performance is not good, so
you depress the pedal, and the braking necessary, give the braking system less you should clean the salt off in time.
distance will enlarge. prssure. At this time,you should not
Notice
continue to step on the brake
·Check brake fluid level at regular
pedal,even if braking is needed. If your vehicle is equipped with the
intervals, according to the request.
front spoiler, you should ensure the air
· After driving through water,rainstorm
·Brake gasket wear mainly due to to front brake unblocked, otherwise the
or vehicle being washed, the brake
driving style,as to vehicle mainly used braking system may be overheated
gasket is wet or frozen, braking
in urban driving,working condition of because of friction.
performance will be obviously
- 45 -
Starting up and Operating
· It indicates ABS is in self-check · ABS warning light will be on if there tube damage or leakage, or one-way
mode and ABS system works normally, is something wrong with ABS system, valve damage, the brake servo unit can
if the warning light is on first, after at this time, conventional braking not work; you should depress the pedal
several seconds, it is off, while the performance is still exist, but you greatly to recover the supplement
vehicle with ABS system is started. should have the vehicle checked by performance of the brake servo unit.
Chery Authorized Service Station, as
· It is normal that the motor makes
soon as possible. Brake fluid
some sound and the pedal vibriates
after ABS is assisting the braking
performance. Brake servo unit Brake fluid tank is mounted on the left
while ABS is assisting braking The brake servo unit usually use
performance, for ABS system will vacuum to work, this apparatus work Check brake fluid level
adjust braking pressure more quickly only when the engine is working, so
- 46 -
Starting up and Operating
between “MAX” and “MIN” lines. Brake fluid is corrosive to the body
Replacement of brake fluid
paint!
Braking system of Chery vehicle is
Brake fluid disposal is a very
equipped with friction gasket braking Brake fluid has hygroscopicity, it will
professional work, SST is necessary,
adjustment mechanism, this obsorb moisture during process of use
so you had better have it replaced by
mechanism can adjust the clearance successively, if brake fluid contains
Chery Authorized Service Station.
automatically after the gasket being too much moisture, braking system
worn, therefore, the brake fluid level will be damaged, at the same time,
may be lowered during process of use, boiling point of brake fluid will be Parking
it is normal, do not worry, but the level lowered, it will severely influence
is obvious lowered or fluid leaks in a braking effect and safety.For the ·With the brake pedal pressed down,
short time, you should have braking above-mentioned causes, you should fully depress the parking brake pedal
system checked and repaired by replace the brake fluid every 2 years or to apply the parking brake securely.
Cherrry Authorized Service Station, as having driven 5000 km. · Shift the selector lever to neutral gear
soon as possible. Notice: Brake fluid is poisonous! Be if you park the vehicle on the level
sure to store it in the original sealing surface; shift the slector lever to
container, keep it away from children. reverse gear if you park the vehicle
down the hill; shift the selector lever to
- 47 -
Starting up and Operating
position “1” if you park the vehicle on cold weather,if the vehicle fords wheels during sudden braking or
water while driving (brake components
when climbing a gentle slope. get wet) or vehicle being washed,it is braking on slippery road surfaces.This
· Keep all windows and skylight easy for this circumstance to occur.If assists in providing directional stability
the rear brake is frozen, you should:
closed. 1. Pull up the parking brake pedal; and steering performance of the
· Turn the ignition key to posittion “1”, shift the selector lever to gear 1 or vehicle under these circumstances.
reverse gear.
pull the key out. 2. Lock up the rear wheel, in order to The anti-lock brake system becomes
· Lock all the doors and trunk lids. avoid vehicle moving.
3. Release the parking brake. operative after the vehicle has
· Bring the vehicle to a complete stop. 4. Drive the vehicle slowly for a while. accelerated to a speed, it stops
operating when the vehicle decelerates
Notice: It may cause fire because the
exhausting parts are very hot, before Anti-lock brake system (ABS) to a speed, and ABS makes use of
parking,make sure that there is no sensor to react the speed
flammable objects around the vehicle
such as grassland or straws.The difference.The system inspects the
The anti-lock brake system is a kind of
vehicle may unexpectedly move while locked wheel speed being at hand, and
being parked,therefore:1. Fully depress advanced electric braking system, it
the parking brake pedal to apply the has corresponding brake force under
can prevent vehicle from sliding while
parking brake securely.2. Park the control through electric signal.
vehicle on solid road. 3. Do not make braking.
the vehicle aligned while parking on “ABS” warning light will come on
the slope.4. Using parking brake will The anti-lock brake system is designed
when the ignition key is turned to the
cause rear brake damage while to automatically prevent lock-up of the
driving.5. Parking brake maybe frozen “ON” position.After several seconds,
- 48 -
Starting up and Operating
the light will go off.If the light comes anti-lock brake system work for on brake pedal and clutch pedal, doing
on while you are driving or the light you,just hold the brake pedal down this will have the steering system fully
remains on when the ignition key is more firmly,whatever the road surface under control.
turned to the “ON” position, it warns conditions are.
We recommend you should go up with
that there is a problem somewhere in
ABS system is designed to maintain the ABS brake technique as soon as
your anti-lock brake system.Even if
maximum braking effect, by means of possible, in order to provide better
the anti-lock brake system should fail,
adjusting braking pressure of every braking capacity for your vehicle.
the brake system will still operate
wheel, at the same time, this assists in
conventionally.Contact your Chery
providing directional stability and ABS self check
Authorized Service Station as soon as
steering performance of the vehicle.
possible.
You may hear a sound along with The anti-lock brake system is in the
slight vibraiton.This means that the self check mode, when the engine is
Braking with anti-lock brake
anti-lock brake system is working started.
system normally. You may hear a slight mechanical
You may feel the brake pedal pulsating anti-lock brake system function is in system is in the self check mode, and
and hear a noise,in this situation,let the action, put forth your strengh to step does not indicate a malfunction.
- 49 -
Starting up and Operating
Notice: While driving through water, the
Parking distance changes much Steering system
considerablely, according to road and parking brake will not hold the vehicle
driving conditions, therefore: 1. securely, the vehicle is hard to be
Always maintain a safe distance from Power steering oil tank is located on
the vehicle in front of you. 2. Avoid towed, and furthermore, the vehicle
the left and front side of engine
high speeds on wet or slipery road. has a possibility of going out.
The anti-lock brake system can not compartment, near the battery.
Water entering the intake pipe of
overcome accident resulting from Maximum steering angle of the left
engine may cause severe damage to
careless or incorrect operation, front wheel is: 30º
the engine.If you drive through deep
therefore: 1. You should be careful to Maximum steering angle does not
water; water will enter the
drive. 2. Decelerate while making a exceed 40.0°
transmission through the vent, causing
turn. 3. Press the brake pedal firmly
damage to the transmission.
and remain on. Driving through water
If the “ABS” warning light comes on While driving through water, be sure
while you are driving, it warns that to drive the vehicle slowly while
there is a problem somewhere in your Drive the vehicle cautiously and
anti-lock brake system.Therefore: slowly, if you have to drive through lightly pressing the brake pedal for
1. Parking the car and contact your water, especially you do not know several times, to dry the brakes, for the
Chery Authorized Service Station as condition of the water.
soon as possible. brakeage will be weakened if the
2. Before driving, have the system Notice: Do not drive forward, if the brakes are wet.
checked by perfessional personnel. water floods the rims.
- 50 -
Starting up and Operating
may be damaged if you do not observe engine overheated)
Ternary catalytic converter
the following tips: · Start the engine by means of towing
· If the engine can not start, the engine (unburn gasoline will enter the
Leaded gasoline is harmful to the
works abnormally after cold starting, catalytic converter)
catalytic converter and electrical
engine power is not in good Have all maintenance work done by
control system, do not use leaded
condition or any other abnormal Chery Authorized Service Station.All
gasoline.
phenomenon indicating ignition components of electrical control
In the case of vehicle with catalytic
system malfunction occurs, you system, injecting system and ignition
converter, fuel filler port of fuel tank is
should drive at low engine speed in system work normally, will reduce
too small for the leaded gasoline filler
a short time. emission pollution and extend catalytic
gun to insert.
converter life.
You should avoid:
· Frequently cold start the engine.
· Working hour of engine is too long, How to save fuel and make
Notice while restarting (fuel injecting hour, in
Do not use leaded gasoline, in order to starting stage, is postphoned) your vehicle last longer, too?
avoid damaging the catalytic converter. · The fuel tank becomes empty
The catalytic converter and vehicle (abnormal fuel supply will result in How to save fuel mainly depends on
- 51 -
Starting up and Operating
your operation mode. to refuel for acceleration)
Here are some specific tips on how to · Do not carry unneeded weight in your
save fuel as possible as you can: vehicle.
· Start driving steadily, accelerate · Do not rest your foot on the brake
slowly and smoothly. pedal, this causes unnecessary wear,
· Avoid engine idling. even damage the brakes and causes
· Do not use air conditioning, unless it greater fuel consumption.
is necessary.
· Drive at low speed on uneven road
surface.
· Keep your tires inflated at the correct
pressure, in order to avoid wasting fuel,
in order to make the tire last longer.
· Keep a proper distance from other
vehicles, to avoid sudden braking,
doing so can reduce wear on your
braking friction discs. (You can save
fuel because it is not necessary for you
- 52 -
Instruments and Controls
- 53 -
Instruments and Controls
- 55 -
Instruments and Controls
as soon as possible. ignition is not on. After filling the fuel
Engine coolant temperature
Notice: When the needle gets into the tank, the fuel gauge reading will get
gauge red zone, it shows that the engine into the new level slowly, when the
maybe successive hot. You should pull
your vehicle up in order to cool the ignition switch is on. The needle
engine, and then have coolant level would not remain at the same point
The gauge indicates the engine coolant checked immediately.
when braking, accelerating or steering,
temperature when the ignition switch
which is caused by fuel vibration in
is on “2” position.
fuel tank.
The needle should within the normal H Hot
·
range while driving normally. The C Cold
needle maybe drift off the normal Capacity of fuel tank: 55 liters
range if the outside temperature is very
high and engine is loaded heavily. In
spite of this, you can still drive F Full
Fuel gauge
normally if the coolant warning light is E:Empty
not on. But you must turn off the
engine if the coolant warning light is The gauge indicates the level of the
on, and have cooling system checked remaining fuel in the tank. The gauge
will not show fuel level when the
- 56 -
Instruments and Controls
Door Open Warning Light
Fuel warning light Engine malfunction indicator light
This light remains on until all the
doors are completely closed. Please
This light comes on when the fuel in
check if all the doors are closed
the tank becomes nearly empty. It will
properly once the light comes on.
come on if the remaining fuel is no
more than 10 liters in the tank. When
this happesns, the fuel tank needs to be
refilled as soon as possible.
Notice: If the fuel approaches empty,
catalytic converter and fuel system will
The light will come on when the
not work properly; therefore, fill the
fuel tank as soon as possible when the ignition switch is turned on, and the
fuel warning light comes on. light will go off after seconds.
If the light comes on, it indicates a
malfunction somewhere in the engine.
When this happens, you can still drive
for a short time, because the electric
injection system switchs to the
- 57 -
Instruments and Controls
emergency working procedure. if the oil level is normal.
Nevertheless, you should contact with Notice
Chery Authorized Service Staion for If oil pressue warning light remains on, it
troubleshooting immediately. indicates malfunction. You should check
Engine Malfunction Indicator Light it to see whether or not it is lack of oil.
may comes on briefly and then goes Please refueling if necessary; if the oil is
out, which is normal. normal, have the vehicle checked by the
Notice nearest Chery Authorized Service Station.
The light will come on with ignition on, it
If Engine Malfunction Indicator Light
will go off after the engine being started.
stays on for a long time, it indicates a
If the light flickers or stays on while you
malfunction somewhere; you should
are driving, you should check the oil level
contact your Chery Authorized Service
immediately. Fill the recommended
Station for troubleshooting.
engine oil to normal oil level position
promptly, if the level is lower than
Low Oil Pressure Warning Light
regulated minimum value. Please have
the lubricating system checked by your
nearest Chery Authorized Service Station,
- 58 -
Instruments and Controls
Release hand brake to the full before brake can not work normally, please
Brake system warning lamp driving. If the warning light is still on contact Chery Authorized Service
after you fully release hand brake, it Station for assistance in time.
indicates that brake fluid is in badly
Notice
need to be added. At that time, you Turn ignition on and pull hand brake.
should: If the brake system warning light is not
on, it indicates something is wrong
· Stop the car immediately. with the system. You should check the
· Check brake fluid level. If necessary, electric bulb to see if it is of
malfunction. If the bulb is normal, you
add Chery recommended brake fluid, should check the brake system. It
and let the level between “MAX” and indicates brake fluid level is low if the
brake fluid warning light is always on,
“MIN” lines. which will influence braking
·If you are sure that the brake works performance. You should decelerate
gradually and stop the car to check the
normally and braking system is safe vehicle as follows:
enough, have your vehicle checked by
Brake system warning light will be on
the nearest Chery Authorized Service 1. Check the brake fluid tank. If the
if you pull hand brake with the ignition
Station. level is too low, add the appointed
on; the light will be off if you release
·If you find that brake fluid leaks and brake fluid.
hand brake.
warning light is always on, or the 2. Check the brake to see whether or
- 59 -
Instruments and Controls
not it is in good condition. then go off after seconds when the you should have the brake system
3. You should drive cautiously and ignition is on. checked by the nearest Chery
slowly to Chery Authorized Service Authorized Service Station as soon as
Station for inspection, if the brake is possible.
normal.
4. Contact Chery Authorized Service Generator warning light
Station as soon as possible, if the
warning light is always on and the
brake is abnormal, or brake fluid It indicates that the battery is
discharging, if the generator warning
leaks. light is on.
5. Braking distance, braking force and If the light is not on with the ignition The warning light will be on with
ignition on; the light should be off
pedal travel will be enlarged, if the on, or it is always on, please contact after the engine is started.
brake fluid level is too low. Chery Authorized Service Station for If the light is on while driving, you
should:
assistance. · Park the car on the raodside.
If the light is on while driving, it warns · Check the generator belt to see
ABS warning light whether or not it is loose or cracked.
that there is a problem somewhere in · If the belt is normal, there may be
ABS system. But the brake system can something wrong somewhere in the
ABS warning light will come on and charging system. you should have the
still operates normally. In spite of this system checked by the nearest Chery
- 60 -
Instruments and Controls
Authorized Service Station as soon as
possible. Safety belt warning light Safety airbag warning light
Notice
The generator may be overheated if the It shows airbag system is normal if the
generator belt is too loose, causing
light comes on and then goes off after
generator damge. So you should have
the generator belt checked frequently. seconds when the ignition is on. If the
light is not on or the light keeps
flickering or stays on long, there must
be wrong with the airbag system. You
should have your vehicle checked by
Chery Authorized Service Station as
When the ignition is in position “2”, soon as possible.
safety belt warning light will be on, if
the driver does not wear the seat belt Turn signal warning light/danger
securely.
warning light
- 61 -
Instruments and Controls
but the green arrow is not on. Position 2: turn on both front fog light
and rear fog light, or only turn on the
High beam indicator light rear fog light.
When the switch is in position 2, the
For high beams, turn the headlamp on, indicator light will be on.
the high beam indicator will come on After the ignition is turned on, front
then. fog light can work only if the parking
light is on. It can work simultaneously
with the high-low beam headlights.The
After the turn signal warning light or
danger warning light switch has been rear fog lamp can work simultaneously
turned on, if the indicator flickers, it only with the front fog lamp.
indicates turn signal light or danger
warning light works. If the flicker You are allowed to use the rear fog
frequency is quite short, it indicates lamp, only if they are needed when the
that there is a problem somewhere in
the electric bulb of turn signal light. visibility is very poor, for the rear fog
Notice light is very dazzling. (Visibility is
If the bulb is damaged, replace it as Front fog light/rear fog light switch
soon as possible in order to avoid within 50m)
accident. Please check the fuse and
bulb to see whether or not they are Position 1: turn on front fog light.
burned out, if you send out turn signal,
- 62 -
Instruments and Controls
- 63 -
Instruments and Controls
At that time, the light switch should be Be sure to comply with relevant traffic
always in “ ”position. regulations, while you use the
above-mentioned turn signal light and
illumination equipments.
- 64 -
Instruments and Controls
The wiper has 4 gears, from top to windshield is dry. It may scratch the
glass and will result in wiper blade
bottom; there are automatic updrift, wear too early.
automatic downshift, offdrift and
intervalshift. Windshield washer switch
From left to right, interval control of
wiper has 4 gears; the wiping time
Turn ignition on and move the lever
interval of every gear will be
towards steering wheel direction, and
prolonged gradually.
fluid of the washer will squirt on the
Notice
windshield.If you pull the lever for a
If there is no water, rear windshield
very short time, fluid of washer will will scratch surface of the glass,
resulting in wiper blade wear too early,
squirt on the winshield first, then the
hindering front field of version. Please
wiper will stop after running for do not use windshield wiper, if the
windshield is dry.
several turns. If you hold the lever
firmly, windshield wiper will continue
Notice to work until you release the lever. The
Damaged wiper blade can not work wiper stops working automatically.
normally. It will block your vision. So
you should replace it immediately. Do
not operate the wipers if the
- 65 -
Instruments and Controls
switch
Press the danger warning light switch
on the dashboard, then you can turn
Turn on the low beam headlight, adjust the danger warning light on, all the
the light beam range to see clear the turn signal lights will come on
front way. simultaneously. Press it again, these
Rear Window Defroster Switch
Night adjustment switch is used to lights will be off. No matter whether or
adjust the light intensity of the not the ignition is on, the danger
instrument panel. warning light can be operated. You
should warn the other drivers while
emergent braking or the traffic being
blocked by means of using danger
warning light. Of course, you should
avoid parking on the traffic lane as
possible as you can.
To defog or defrost the rear window,
you should push the switch with
iginition in the “2” position.
- 66 -
Instruments and Controls
An indicator light will illuminate to window is clear.When it snows,wipe clock: Push the button 4 seconds, then
indicate the defroster is operating.
Push the switch once again to turn the snow off the window first,then turn on the hour digital will flicker frequently.
defroster off. the rear window defroster, for the The digital will increase one hour
defroster is not designed for melting every time you depress the button.
Notice
snow. After reset the hour, wait 5 seconds;
The thin heater wires is on the inside
the Minute digital will flicker
of the rear window, if it is damaged, it
Digital clock automatically. The digital will increase
will lose defroster function, therefore,
one minute every time you depress the
be careful not to scratch or damage the
button.
heater wires while cleaning the inside
After adjustment, wait several seconds;
surface of rear window,do not use
the digital display will not flicker any
sharp tools or corrosive
longer, it shows that time is set
detergent.Defroster will consume
properly.
much more power,causing the battery
Notice
to discharge,so do not use defroster The digital clock indicates the time
After battery is disconnected or fuse is
while the vehicle is started or the with iginition on.While you want to
replaced, time should be reset once
engine does not work yet.Make sure reset the time, you can push
again.
you turn the defroster off when the corresponding button on the digital
- 67 -
Ventilation System and Air Conditioning System
- 68 -
Ventilation System and Air Conditioning System
Side vent
Central vent
Foot vent
Control panel
- 69 -
Ventilation System and Air Conditioning System
- 70 -
Ventilation System and Air Conditioning System
on the air-blower.
1
Control panel
Central vent
1. Airblower switch
2. Temperature control switch Air after adjustment can flow in the
3. Airflow distribution switch vehicle through two central vents; you
4. A/C switch can change direction of airflow 2
5. Internal circulation switches through changing the angle of in-take
grille.
Knurle wheel 1 turn upward- vent is Bypass vent
Ventilation and warm air
open
Knurle wheel 1 turn downward- vent is Air after adjustment can flow in the
A/C system adjusts temperature by
closed vehicle through two bypass vents.
means of mixing cold and warm air;
Knurle wheel 2 Turn to left- airflow is
furthermore, temperature remains the
towards left
former state at any speed.
Knurle wheel 2 Turn to right- airflow
Airflow speed is decided by the
is towards right
air-blower. If necessary, you can turn
- 71 -
Ventilation System and Air Conditioning System
side window through this vent; it can
get rid of moisture on the glass.
- 72 -
Ventilation System and Air Conditioning System
while driving, if you want to feel more
comfortable.
Airblower switch
Airflow distribution switch is used to
select direction of airflow.
Airblower switch has airblower speed
Airflow distribution switch There are 4 positions on this switch:
under control (There are 4 gears in all),
Panel
turn the switch in “0” position if you
Bi-level
want to turn off the airblower. You can
Floor
make use of air blower to adjust the
Windshield
windspeed. Turn on the airblower
- 73 -
Ventilation System and Air Conditioning System
- 74 -
Ventilation System and Air Conditioning System
A/C system
- 75 -
Ventilation System and Air Conditioning System
A/C switch: Press button of A/C Temperature control switch: Turn the
Internal circulation switch: Press switch to requested position
button of Airblower switch: at will
Airflow distribution switch:
Temperature control switch: Turn to
Notice: Do not use “the strongest
the end counter clock-wise (blue) heating” for a long time, in order to
Airblower switch: Put on gear 4 avoid inside air becoming foul and
window having fog. Turn off the
The strongest heating internal circulation if the windows
A/C switch: Closed have fog or moisture. “Complusive
heating” is only used for rapid heating,
Internal circulation switch: Press the then turn to “normal heating” as soon
button on as possible.
Normal refrigeration Airflow distribution switch: Normal heating
Nomal refrigeration while Temperature control switch: Turn to
A/C switch: Closed
long-distance driving or driving at high the end clock-wise (red)
Airflow distribution switch:
speed. Airblower switch: Put on gear 4
or
A/C switch: On
Adjust button between and
Airflow distribution switch:
if there is steam on the
or
- 76 -
Ventilation System and Air Conditioning System
windshield glass. the temperature control switch
Temperature control switch: Turn to between cold (blue) and warm (red).
desired heating position A/C switch: ON/OFF
Airblower switch: Put on gear 1 or Air distribution switch:
gear 2 Temperature control switch: Turn the
Notice:
It will improve the defog effect if you switch to the requested position
turn A/C on.The windshield could fog Fan switch: at will
up because of the difference in air
temperature inside and outside of the
windshield, it will affect your vision; Ventilation
therefore, do not use , if the
Outside air flows in through central
weather is very damp.
Defroster vent and both sides vents.
A/C switch: On Panel and floor A/C switch: OFF
Airflow distribution switch: They are used just transitionally, when Air distribution switch: or
Temperature control switch: If nessary, the outside temperature of vehicle is tune-up to other position accordingly.
turn to heating positon low and there is no sunshine. Warm air Temperature control switch: Turn the
Airblower switch: Put on gear 2 or flows into the bottom zone of vehicle switch to the end
gear 3 and cold and normal air flows into the Airblower switch: at will
upper space of vehicle, if you adjust
- 77 -
Ventilation System and Air Conditioning System
life of the whole system. air conditioning consumes power of
Operating tips
The compressor of air conditioning the engine, causing greater fuel
does not work when the airblower is consumption. In order to minimize the
In order to cool off your Chery after it
turned off. running time of air conditioning
has been exposed in the sun, you
Make sure the air intake grilles in front system, you should pay attention to the
should open the window before turning
of the windshield are not blocked by following matters:
on the air conditiioning system.
ice, snow and leaves, which ensures 1. To cool off your Chery after it has
Refrigeration of cooling system may
heating and ventilation system work been exposed in the sun, you should
be not enough because of frequent
normally. open the windows or doors for a short
parking and braking, while you drive
It is normal that there could be time, which vents the hot air and allow
in heavy traffic area. If you have not
condensed water from the drainpipe of the air conditioning to cool the interior
used the air conditioning system for
evaporator when the ambient more quickly.
one month or more than one month,
temperature and humidity are high. We 2. Do not turn on the air conditioning
you should turn on the air conditioning
recommend that you should keep away system while driving with the window
at least once a month run it for minutes
from the cold air. open.
with the engine idling to maintain the
Economic Operation of air
lubrication and sealability of the
conditioning system
compressor and prolong the service
While refrigerating, the compressor of
- 78 -
Audio System
- 79 -
Audio System
- 80 -
Audio System
- 81 -
Audio System
1. Preset key 1 8. Power switch 13. Preset key 5
RANDOM CD random
play/stop 9. Display 14. Preset key 4
DISC+ Select disc
2. Preset key 2 10.BAND Wave band backward
SCAN Radio frequency
3. Preset key 3 scan/CD programme scan 15. FF
REPEAT CD repeat/stop High and Low
Terminal Searching 16. REW
4.SOURCE Sound source Play
Previous/Next Programme 17. Eject the cassette tape
5.SOUND short-time CD box
press Sound effect mode Music searching system Short-time press
SELECT Long-time Reverse cassette
press Audio setting mode 11.AST Automatic store Long-time press Eject the
cassette tape
6.MUTE 12. Preset key 6
7. Volume DISC- Select disc forward 18. Cassette
- 82 -
Audio System
music you are listening to, such as jazz, select sound effect mode you like.
- 83 -
Audio System
plays the next station up or down the known the frequency of desired radio
Radio
station band. station)
Automatic seeking · If you want to enter manual tune-up
Wave band
To seek a station, push the “ ”or “ ” mode: see item “TUN” of “SETTING”
Press BAND key, if you want to select
side of “TUNE/SEEK” until you hear for reference,set it as “MAN”.Let the
the wave band you like.
a beep. radio in manual tuning mode,until you
FM1 FM2 FM3 FMAST FMA-
The flexibility of seeking (FM only) come to “AUTO” mode.
MW AM MW AM MW
·Flexibility of seeking can be adjusted,
AM AST LW.
see the item “SRCH” of “SETTING” To preset a station
Notice
for reference. Store the radio station using munual
You can cancel wave band of MW
preset key
AM or LW out, if you do not like.
Frequency scan Preset keys (from 1 to 6) are used to
You can cancel them out accordingly,
The local radio station will play preset and tune in radio station.
if you do not want too much preset
present wave band for 10 seconds. ·Tune in the desired station
radio station of FM or MW AW
· Press SCAN key at least 2 seconds, if · Push and hold down the button at
you want to turn on/off the frequency least 2 seconds, for the station you
Automatic seeking
scan features. want, this will set the station to the
In the seek mode, the radio finds and
Manual tuning (if you have already preset key.
- 84 -
Audio System
While setting FM radio station, again. REW/FF (Rewind/Fast forward)
corresponding RDS information and —You can begin to listen to the radio ·Press to fast forward a cassette
AF mode (on/off) are set together. station set in preset key 1. tape:
Listen to the preset station —Sometimes, perhaps, you cannot ·Press to rewind a tape.
·Push the button (from 1 to 6); you can find exactly 6 stations. —If the radio was previously on, it
listen to the preset station you want. will come on again. If the tape rewind
Automatic station storing Cassette player to the end, it will play again.
You can store 6 strongest FM radio Music searching
stations on wave band of FM AST or system-previous/next
·You can turn on the cassette player by
wave band of MW AM AST.The Select how many songs you want to
inserting a cassette tape.
stations which are stored in wave band ignore, from the current programme.
·If the cassette tape is already in the
of FM AST or MW (AM) AST ·Press key for prvious
player, press SOURCE key to select
previously, will be covered, if you use ·Press key for next
the cassette as sound source. Let it go.
automatic station storing performance. —It is mute until you get desired
Changing side
·Push AST key to enter automatic programme. It can only recognize
·Push key to change side.
storing, then programme at least having 3 seconds
—One side of the tape finishes,it will
—You hear a beep, and then mute. intervals.
change to other side automatically.
—After storing, you hear a beep once Eject the cassette
- 85 -
Audio System
·Press key to eject a cassette. regularly (once or twice every ·Press key or key,if you want to
month). select desired programmes.
Caring for your cassette tapes —It begins to play from the selected
- 86 -
Audio System
Repeat feature hours mode) or “AM 12:00” (12 hours You may change the original setting of
·Press and hold RANDOM key at least mode) the player if you like.
2 seconds,in order to activate or turn —Hour digital begins to flicker. ·Press SETUP key, if you want to enter
off random playing. ·Press SETUP key, if you want to SETUP
Eject the disc adjust the hour. ·Press key key, if you want to
·Press key ,if you want to eject a ·Press key to select minute digital select item you want to change
compact disc. —Minute digital begins to flicker. ·Press SETUP key, if you want to
· Press SETUP key, if you want to change the setting
Clock setting adjust the minute. ·Press SETUP key at least 2 seconds,if
·The clock begins to work from the you want to log off SETUP menu.
adjusted time. The player will log off SETUP mode
·Press SETUP key at least 2 seconds, if
·Press SETUP key at least 2 seconds, if automatically, approximate 1 minute
you want to enter SETUP menu.
you want to log off SETUP menu. after your last operation.
·Press key to “TIME” item.
—If clock mode is activated, the
·Press SETUP key, if you want to
display will show the time, after any
select “12H” or “24H”
key operates 10 seconds setting.
·Press key to select hour digital
Setting
—Display shows that:“0000” (24
- 87 -
Audio System
or [Setting]
RADIO [EUROPE LATAM Select the tuning according to European, Latin American,
AMERICA ASIA] American and Asian standards.
TAPE [-2 -1 0 +1 +2] Cassette player volume has something with the tuning.
CDC [-2 -1 0 +1 +2] CD player volume has something with the tuning.
BEEP [-2 -1 0 +1 +2] Select and confirm volume of “beep”.
TIME [OFF 12H 24H] Select desired clock mode.
- 88 -
Audio System for Songs (Optional)
- 89 -
Audio System for Songs (Optional)
Display
- 90 -
Audio System for Songs (Optional)
1.Up and down and station key DISC key 16.RPT(Repeat key
key
9. Exit key 17.SCN Beginning or
2. Function key programme scan key
10.REW Rewind
3. Knob 18. Preset key
11. PROG
4.A-M Frequency mode 19. Function key 2
key 12.FF Fast Forward
- 91 -
Audio System for Songs (Optional)
Lock FF/REW Holographic liquid crystal display
Performance
Permalloy double crack cassette head Monitor mode
DIN case
Tuning
Audio frequency
Electric quartz locks PLL tuning
Electric frequency control Case
AM/FM wave band-: one AM wave
band, four FM wave bands.
(VOL/BASS/TREB/BAL/FADE)
20 FM radio station/5 AM radio station DIN case with ISO supporting capacity
4-track balance control
touching key memory Dimensions:
Z-enhancer with 3-mode selector
Searching for tuning towards high 178mm height*50mm width*152mm
160W 40W*4 maximum power
frequency/low frequency thickness
output
Preset radio station scan (PS)
Automatic radio station store (AS) Caring for your cassette player
Overall
FM reception system
and tape
Cassette player Night illumination
Auto-reverse Digital quarz colock 1. Tighten the tape before you insert it,
Active antennal starting trigger for loose one may hinder the operation.
- 92 -
Audio System for Songs (Optional)
You should pay special attention while Radio cassette player CD
Operation method
using C-90 or prerecording cassettes. changer radio
2. Please use cassettes with a total
Basic operation Notice:
playing time of C-30 to C-90. Avoid The operation mode will not be
using cassettes with a toatal playing Notice: selected if you fail to connect the parts.
Be careful to tune-up the volume, for “CASS” will appear if you fail to
time longer than C-120.The tape used insert the cassette, “DISC” will appear
engine noise will damage your ears, if
in these cassettes is thin and could get the volume becames maximum, while if you fail to insert CD in CD changer.
stuck or tangled in the cassettes player. power supply gets through.
3. Please clean the tape head by using 3. Turn knob 3 to increase the volume
1. Press FNC of key 5. of sounds clockwise; turn it counter
a cleaning tape, at regular intervals,
keep anything magnetic or hard away clockwise to decrease the volume of
Notice:
from the tape head. Push POWER key for 1 second or sounds.
more, if you want to turn the power * Volume from 0 (MIN) to 33 (MAX).
4. Do not put oil in the mechanism. supply off.
5. Do not leave a cassette in the player Frequency mode adjustment
if you are not listening to it, especially Press A-M of key 4, if you want to
2. Press FNC of key 5, if you want to
if it is very hot or cold outside, for the select the adjustment mode, every time
select operation mode. Every time you
cassette is very easy to be damaged. you press, mode is switched as
push, the mode is switched as follows:
follows:
- 93 -
Audio System for Songs (Optional)
BASS TREB BAL FAD-previous 1. Press A-M of key 4, if you want strengthen sound of the left
mode to select “TREB”. loudspeaker.
2. Turn knob 3 to increase the TREB
Notice:
BASS adjustment clockwise; Turn it counter clockwise to Factory default setting is “0”.(Range
1. Press A-M of key 4, if you want to decrease TREB. of adjustment is from L9 to R9)
select “BASS”. 2. After adjustment, press A-M of key
Notice: 4 until it is in operational mode.
2. Turn knob 3 clockwise, if you want Factory default setting is “0”. (Range
to increase the bass; turn it counter of adjustment is from -6 to +6)
clockwise, if you want to decrease the 3. After adjustment, press A-M of key FADE adjustment
- 94 -
Audio System for Songs (Optional)
“Z-ENHANCER OFF” display mode.
3. After adjustment, press A-M of key “Z-ENHANCER 1”…… 1. Press BAND of key 6, at the same
4 until it is in operational mode. Z-ENHANCER 1 Bass enhanced time, press DISP of key 14 for at
Z-ENHANCER 2 High pitch least 2 seconds, clock editing
Z-enhancer setting enhanced mode is started. It will flicker for
This device is equipped with 3 kinds Z-ENHANCER 3 Both enhanced you to edit.
tone effects stored in the memory, Z-ENHANCER OFF No sound effect 2. Use up (hour) and down (minute)
select whichever you like. of key 1, if you want to move
Change display between hour and minute.
Notice:
Factory default setting is “Z-EHCR Press BAND of key 6, at the same time, 3. Press BAND of key 6, if you
OFF”. press DISP of key 14,if you want to want to store clock setting.
enter clock display mode.
Every time you press Z-EHCR of key Notice
Main display Clock display Main The clock setting will be cancelled out
7, tone effect changes according to the display if you select other operation mode,
following orders: before you complete the
above-mentioned operation; the clock
“Z-ENHANCER Clock setting will turn to 1:00, if you take the battery
1” “Z-ENHANCER 2” out for check and repair, at this time,
Press BAND of key 6, at the sametime, please set the clock once again.
“Z-ENHANCER 3” press DISP of key 14 to enter clock
- 95 -
Audio System for Songs (Optional)
Press stop key 9, and the cassette will
Cassette player operation Radio reception
be ejected.
*The audio system will in radio mode
Insert cassette FM reception
4 seconds after cassette being ejected.
In order to impove the reception effect,
You can turn on the cassette player by
inserting a cassette tape. It plays the tuning contains signal stimulous
REW/FF
automatically. stereophonic sound and multichannel
*Auto-reverse mechanism starts, if one Use FF of key 12 and REW key of 10
side of cassette is over, it play the other noise reducer return circuit.
Fast forward a cassette tape.
side automatically. Listen to radio
Notice: Rewind a cassette tape
Insert the cassette to the slot 1.Press POWER of key 5 to select
You can listen to the radio, during the
completely. radio mode. The radio is turned on.
process of REW/FF or searching
2.First BAND of key 6,then select
operation.
Listen to inserted cassette FM1, FM2, FM3, FM4 or AM, if you
Press FUNC key 5 to select cassette want to tune desired preset radio
player mode, it begins to play Change the other side
station, Eevery time you press BAND
automatically. Press PROG of key 11, FF of key 12
key, wave band changes as follows:
and REW of key 10 simultaneously;
FM1 FM2 FM3 FM4 AM
the cassette player will reverse to the
Ejecting cassette FM1
other side of cassette automatically.
- 96 -
Audio System for Songs (Optional)
3. Use corresponding preset key 18, if selected. 3. Press corresponding preset key 18
you want to select desired radio 3. Use up or down key 1 to select for at least 2 seconds; store the
station. desired high or low frequency. station in the memory.
1. Press BAND key 6, select wave
Searching for tuning Preset radio station band of station you want to store.
1. Press BAND key 6 to select desired You can preset 25 radio stations in all, Press and hold AS key 8 for 2
wave band. wave band of FM1, FM2, FM3, FM4 seconds or more. Station with
2. Press up or down key 1 for or AM, each has 5. good reception will be stored in 5
searching towards high frequency or preset key 18 automatically (from
Notice:
low frequency. Tuning will stop The previous stored station memory 1 to 5).
automatically if you find a station. will be canceled out if you preset Notice:
station once again.
If there are no 5 stations whose
Manual tuning reception is good, previously stored
Manual preset station
1. Press BAND key to select desired stations on the remaining keys will not
1. Press VAND key 6, select wave
wave band. be canceled out.
band of your desired station.
2. Press VAND key 2 seconds or
2. Use up or down key 1 to tune-up Preset scan (Preset station scan)
more “MENU” will appear on the
the station you desire to preset.
display, manual tuning mode is
- 97 -
Audio System for Songs (Optional)
Press PS key 8,preset memory number Programme number Programme from the previous song.
will flicker; stations will be tuned in at time Programme number REW/FF
7 seconds interval, accordingly. Press
PS key again to cancel the preset scan Stop (pause) • Fast forward
mode out. Press play/pause of key 13 Rewind
Notice: Press play/pause of key 13 for * Press up/down of key 1 one second
Auto-stored mode is set if you press recovery. or more to forwards or rewind the disc,
PS key for 2 seconds or more. it is 5 times faster than the common
Selection of CD one, if you press it 1 seconds or more,
Press disc key 8 of disc selection to it will be 30 times faster than the
CD changer mode operation method select CD you want to play. common one, if you press it 3 seconds
or more.
Audio mode Programme selection (songs)
1. Press POWER of key 5 to select CD Up/down key 1 Scan (Beginning of programme
changer mode, CD player is turned on. • Play from next song. scan)
Play from beginning of
*Press DISP of key 14, programme current programme. Press it Push “SCN” of key 17, “SCN” will
time will appear on the display. again; CD will begin to play appear on the display, the compact disc
- 98 -
Audio System for Songs (Optional)
player will play the next track for 10 programme. process will be continued until you
seconds. This process will be push the button again to turn off the
continued until you push the key again RPT (Repeat) repeat feature.
to turn off the scan feature.
*It will begin to play after the current Random
Push “RPT” of key 16, “RPT” will
progrmme.
appear on the display. This process
will be continued until you push the Press RDM key 15, “RDM”will
CD player scan
button again to turn off the repeat appear on the display; all the
feature. programmes will be random played.
Push “SCN” of key 17 for at least 2
It will exit from random mode, if you
seconds, “DISC” and “SCN” will
CD repeat press RDM of key 15 once again.
appear on the display. The compact
disc player will play 10 seconds the
Push “RPT” of key 16 for at least 2 Specifications
previous of all the programmes. This
seconds,“DISC” and “RPT” will
process will be continued until you
appear on the display, the repeat
push the key again to turn off the scan FM tuning
feature will automatically replay the
feature. Frequency range: 87.9MHz to
current compact disc track. This
* It will begin to play after the current 107.9MHz
- 99 -
Audio System for Songs (Optional)
Actual flexibility: 11dBf 8kHz 0+2/-7 dB *50mm*152mm
50dB non-noise flexibility: 17dBf Power amplifier
Notice
Alternation selection: 70dB Maximum power output: 160W This regulation is up to the EIA
Stereophonic sound separation (40W*4 way) standard, we will not inform you
separately, if the design and regulation
(400Hz): 25dB are changed because of updating the
Preset amplifier products.
AM tuning Bass control (100Hz: 6 dB
Frequency range: 531 kHz to 1,602 Treble control (10 kHz): 6 dB Baisc operation of record
kHz
Actual flexibility: 25uV Overall
changer for 6 CD
Power voltage: 14.4Vdirect current
Cassette player (from 10.8Vto 15.6V is permitted)
Trembling degree (WRMS):0. 4% Power comsuption: less than 10 A 1. Take the box out
Signal way separation degree (1 kHz): 1.1 Open the door upward.
Loudspeaker resistance:4 from
35dB
Signal-to-noise ratio: 120us (common): 10.8V to 15.6V is permitted
40 dB weight 1.3Kg
Frequency response 125Hz 0 3dB Dimensions 178mm width
- 100 -
Audio System for Songs (Optional)
Do not touch the signal side with your
finger, while taking CD out.
1.2 Eject theCD from the box. 2.2 Put CD in the slot with label side
up. 1. For safety, insert a cassette tape or
Eject compact disc into the slot, after
2.3 Push the seat in until it is ok.
disk the vehicle parks securely. In
Notice: order to avoid accident, vehicle
If you make too strenuous efforts, CD
CD seat may get out of the box. At this inside volume should not exceed
Door time, please press the delivery staff to vehicle outside sound.
make it ok. You should put even
strength, and two edges of seat should 2. Clean the vehicle bodies with a
match the box. soft, lint-free cloth. Do not use
2. Insert CD
2.1Buckle the releasing handle with sand paper, benzene, diluent or
3. Take CD out alcohol. You can dampen the
finger, and pull the disc seat out.
Pull the seat out, and take CD out
cloth with water, if the body is
- 101 -
Audio System for Songs (Optional)
3. The slot is very important for the wires while audio system is working, Weight: 1.65Kg
player. The parts will be damaged for it will damage the parts.
if there is so much dirt in. So, you 5. Keep direct sunlight, heater or other Use of CD
should be sure not to keep the heating source away from the player.
player door open for a long time.
. If inside vehicle is very cold,
n When inside vehicle is cold, if Specifications do not use CD player soon after you
you turn on the palyer soon after
turn the heater on, for the moisture will
you turn on the heater, the
Sample frequency: 44.1 kHz get into your compact disc or optical
moisture will get into your CD
Frequency response: 5Hz 20kHz parts of CD player, causing CD player
player. Your compact disc player
1dB cannot work normally. Please wipe the
cannot work normally.
Signal-to-noise ratio: 105dB 1kHz moisture off with soft and clean cloth,
(moisture)
IHE.A if there is moisture on CD surface.
n Wipe the CD with a clean and
Trembling rate: less than minimum Stop it for one hour, and wait until it
soft cloth if moisture gets in. It
volume travel dries, then CD player can work
will dry naturally after one hour,
Power supply: DC14.4V 10.8-15.6V normally.
then the player can work
negative - connecting ground . Bumpy roads may make your
normally again.
Power consumption: less than 1A compact disc player skip.
4. Be sure not to pull the cable and
- 102 -
Audio System for Songs (Optional)
Notice or CD with stabilization apparatus.
Caring for your compact disc
Do not play any other discs, for this They may be pressed inside the
player is designed only for CD with player and discs mechanism and damage the CD player.
disc mark.
1. Handle compact discs carefully, 1. Do not put label on the CD surface;
especially when you are inserting them. do not make marks with pencil or pen
on the CD surface.
Hold them on the edge and do not 2. Do not clean a CD with any solvent,
bend them. Avoid getting fingerprints such as detergent, anti-static electricity
on them, particularly on the shiny side. sprayer or diluent.
2. Wipe dirt and fingerprint off CD 3. Do not use CD with rough edges,
with a soft, lint-free cloth, wipe along deformation and being curled. It will
middle of CD to the edge straightly. cause malfunction or damaging to the
3. A new disc may have rough edges. player.
Remove the rough edges by presssing 4. Keep CD away from direct
the side of a ball-point pen, for this sun-shine or heating source.
kind disc cannot be used or it will skip Notice
over while playing. Do not use the protective paper of CD
- 103 -
Audio System for Songs (Optional)
Error display
In order to protect the system, this player has self-check function. If there is malfunction, it will warn you by means of various
error display. Please correct it accordingly to fix the breakdown.
It indicates that there is a malfunction of mechanism of mainframe or CD changer (such as, you cannot
Er2 change discs or discs cannot pop out.)
Check the mainframe and CD changer.
It indicates that the adapter head cannot pick up signals, for the disc is scratched or there is something
Er3 wrong with the mainframe or CD player.
Check the disc.
Er6 It indicates TOC of CD cannot be read, such as: The selected disc is inserted reversely.
- 104 -
Audio System for Songs (Optional)
Trouble-shooting
Power supply
The fuse is blown out. Replace the burnt fuse; use a new one of same amperage.
malfunction
or there is no There is something wrong
Check the connections of the wires.
sound with the wiring.
Tone quality is poor. Megnetic head is dirty. Clean the magnetic head with cleaning tape.
- 105 -
Audio System for Songs (Optional)
- 107 -
Maintenance and Upkeep
Engine compartment
- 108 -
Maintenance and Upkeep
Always use solid supports for
Maintaining & protective
1.Power steering liquid safety, if it is necessary for you to
bank measures be under the vehicle. In addition,
2. Front bin relay box 1 somebody should be with you for
3. Front bin relay box 2 When you perform maintenance by
assistance, in order to avoid any
4. Expansion tank yourself, utmost care should be
contingency.
5.Washer fluid reservoir taken to prevent unnecessary
Do not allow smoke flame or
6. Oil dip-stick personal injury or vehicle damage.
anything may be cause sparks
7. Oiling port cover Here are a few precautions that you
around the battery and fuel, in
8. Fuse box should be especially careful to
order to avoid any accident.
9. Air filter observe:
While connecting battery cable,pay
10. Battery If the engine is successive hot, turn
special attention to the poles.Do
not connect positive cable to
off the engine immediately, so as
negative cable column or negative
to make it cool, otherwise it is
cable to positive cable column.
possible to damage the engine.
Generally speaking, positive and
Do not get under your vehicle with
negative poles are marked with
just the body jack supporting it.
“+” (positive) or “-” (negative)
- 109 -
Maintenance and Upkeep
distinctively. accident taking place, unless it is it may be running suddenly.
Be careful not to touch the running
Be sure to maintain ignition cables, necessary for the ignition to be parts with the ignition on.
high-pressure cables and high load on.When the engine is running,
Notice:
vehicle cables, otherwise it is easy keep hands, clothing and anything Running engine will cause injury,
to have possibility of fire. ribbon-like from the moving fan scald or electrical shock. Be careful
not to touch the hot parts, such as
If you want to check underneath of and engine driving belts while you exhaust manifold.
engine hood while the engine is are working under the engine
running, park the vehicle on level hood.For these things may be
Checking list for the driver
road surface; put transmission wrapped in moving parts to hurt
lever in neutral gear position, and you or damage the vehicle.Remove
Before driving, you should carry out
parking brake the vehicle. Failure watch, bracelet and ring.
safety maintenance and careful
to do so will lead to unexpected
checks on reliability of vehicle
accident for vehicle unexpectedly Safety attention operation, recommended checkings
moves.
are introduced as follows:
Be sure that the ignition is off,
Cooling fan may be running at all Exterior
furthermore, pull out the key
times. Be careful in order to avoid Tire pressure and state (cold tire
before you work under the engine
personal injury while checking it. only).
hood, in order to avoid unexpected Cooling fan is controlled by ECU, so
- 110 -
Maintenance and Upkeep
Wheel nuts’ degree of tightness Check the instrument or warning Engine compartment
Sensitivity of vehicle operation light of the indicator. Check the engine oil level.
Check to see whether or not there is Check the fuel gauge, for Check the engine coolant level.
oil, coolant or fuel leaks. confirmation of the amount of fuel in Check the battery.
the fuel tank. Check the windshield wiper fluid
Interior Check the position of the rearview level.
Check to see if the steering system mirror. Check brake fluid level.
works normally or not; check to see Check the door lock system. Check steering pump oil level.
if there is some difficulty in operating Check self stroke of clutch pedal, Check oil level of the clutch servo
the steering wheel. (Steering wheel check the clutch pedal to see if it is in unit
feels much more heavier while the good condition.
engine is turned off than the engine is Check self stroke of brake pedal, You should check the engine
started.) check the brake pedal to see if it is in
Check the stroke of parking brake good condition. (You should step on oil level by the following steps
lever and reliability of parking brake. the pedal much heavier while braking
Check horn, windshield wiper and than starting the engine.) It is a good idea to keep the engine
turn signal to see if they are in good Check the safety belt for the driver oil level in proper range in order to
conditionh. to see, if it is in good condition. ensure there are enough lubricating
- 111 -
Maintenance and Upkeep
oil for your vehicle engine. A certain
amount of oil is consumed while the
engine is running; therefore you You should also check the cleaness of
should check the engine oil level at oil on the dipstick; replace oil if the
regular intervals. The vehicle should cleaness degree is not up to the
be on a level ground. After turning standard.
off the engine, and wait a few If the oil level is blow “MIN” level
minutes for the oil to drain back into line, add engine oil in order to make
the oil pan. Pull out the dipstick and the oil level between “MIN” and Please use oil of same specifications,
wipe it clean with a cloth, then “MAX”. while adding the oil.
reinsert the dipstick and push it in as The oil level should not above
Special attention: If the oil warning
far as it will go. “MAX” level line; otherwise it may light is on, but you still let the engine
Pull the dipstick out once more and be cause malfunctions such as oil running, as a result, the engine is
damaged. This is not covered by our
check it to see if the oil level is being consumed too much; spark quality guarantee.
between “MIN” (minimum) and plug accumulates carbon; and cooling
“MAX” (maximum) level lines of the effect is not good (engine oil is
dipstick. foaming) and engine power is not
good.
- 112 -
Maintenance and Upkeep
maintenance). Maintenance
Replacement of engine oil and Capacity
intervals
filter Filter elements should be replaced, Replace it 1.6DOHC-EE479
too, at the same time. every 5,000 3.75L
- 113 -
Maintenance and Upkeep
“MAX” and“MIN” lines.
Coolant level Engine overheating
Notice
Boiling coolant and vapour will spout
If your engine coolant temperature
out under pressure, causing severe
injury. To prevent burning yourself, gauge indicates overheating or you
do not remove the coolant reservoir
suspect that the engine has probably
cap when the engine and water tank
are hot. The engine coolant maybe overheated, please stop the car and
burns your skin and eyes, please take
have a check.
precautions to keep the coolant away
from your skin and eyes. Always use Turn off the air conditioning to let the
the same type of coolant as already in
engine idling for several minutes.
the cooling system. To mix with soft
water, do not mix too much. Please Check the cooling fan to see whether
contact your nearest Chery
When the engine is cold, the coolant Authorized Service Station for or not it is operating. If it is not, turn
level is satisfactory if it is between assistance, if you want frequent ignition off, and contact your Chery
refilling. Please check the cooling
the “MAX” and “MIN” lines on the system. Please use the recommended Authorized Service Station for
reservoir. The coolant level in the anti-freezeing agent and coolant by assistance as soon as possible. If the
Chery.
reservoir will vary with engine cooling fan is operating, and steam is
temperature. If the level is below the not boiling out of the engine
“MIN” line, add coolant between the compartemnt, please open the engine
- 114 -
Maintenance and Upkeep
hood to let the engine idling until it is no steam, keep all people escape “MAX” and “MIN” lines of the
from the vehicle, turn the engine
cooled.If the electric cooling fan is off.When there is no steam, you can reservior.
operating,but the temperature keeps open the engine hood. If the level is low, it probably
high,you should stop the engine to Special attention: Do not attempt to indicates brake system leak or
make it cool. remove the radiator cap when the consumption; you had better have it
engine and radiator are hot. Serious
Then check the coolant level. If the injury could result from scalding hot checked by the nearest repair shop.
level is low, look for obvious coolant fluid and steam blown out under
pressure.
leaks from the radiator hoses, water
tank hoses, water tank, and water
Brake fluid
pumps and under the vehicles.
If the engine is leaking, stop the
Brake fluid is hygroscopic, the
engine immediately; contact the
presence of moisture in the brake
nearest Chery Authorized Service
fluid will do harm to hydraulic brake
Station for consultation as soon as
system. Therefore, the brake fluid
possible.
should be changed according to this
Notice manulal’s instruction.
To help avoid personal injury, keep
the engine hood closed until there is Fluid level should be between
- 115 -
Maintenance and Upkeep
Maintenance intervals Capacity clean water. If you still feel pain,
Gearbox oil
Replace brake fluid every please go to a doctor for help. Have
50000 km or 24 months. brake fluid changed by Chery
You can check the gearbox oil level,
But in harsh condition, 0.45L Authorized Service Station or repair
only if the engine is off, the car is
replace it every 30000 shop. Thoroughly clean the cap
parking on the horizontal road
km or 12 months. surroundings before you open it, for
surface and the gearbox is cold
brake system maybe polluted, and as
enough for you to touch its outer
Make it clean before filling brake a result, the performance is not good.
shell.
fluid. Remove the cap, fill brake fluid You should use Chery recommended
Remove the oil filler plug; check the
until it reaches “MAX” line of the brake fluid, for brake fluid of any
oil level; add oil in small quantities at
reservoir, and then screw the other brands will damage the brake
a time. If the level is too low, add the
reservoir cap backward tightly. system.
oil when the level reaches within the
Notice Special attention: Brake fluid can correct range, and install the filler
Brake fluid can harm your hands and damage paint surface. If fluid plug hand-tight.
splashes on the paint surface, please
eyes, so keep your hands and eyes flush the paint surface with clean
away from the brake fluid. If fluid water.
gets in your eye,flush your eyes with
- 116 -
Maintenance and Upkeep
Notice
After driving, oil temperature of
gearbox may be very high. Please let
the gearbox oil and oil filler plug
cool before you check the oil level. In
order to protect the environment,
please deposite the waste oil and
container properly to the appointed
place.
You have no choice but use regulated
oil of the schedule. Check the
Power steering fluid level
gearbox shell to see whether or not it
leaks or being damaged, after you
When the engine is cold, power
install the oil filler plug.
steering fluid level should be
Maintenance intervals Capacity Air filter
between “MAX” and “MIN” lines of
the reservior. If the level is below
Replace it after the “MIN” line, please add the fluid in Air filter should be cleaned or
first 5,000km, then 1.8L
replace it every time. replaced in time, if the vehicle is
3,000km. always in the environment with too
much dust or dirt.
- 117 -
Maintenance and Upkeep
Notice had better check the sparking plug, at the spark plug with spark plug
If the air filter is not replaced for a
long time, engine performance will regular intervals and remove the spanner.
not be in a good condition, some carbon. You can use sparking plug · Install the new plug or cleaned one
components may be damaged, and
even the engine will be severely brush to remove carbon from in the engine and run it in by hand,
damaged. sparking plug electrodes, and then turn it clockwise several turns. If it is
use a little file to remove carbon on not ok, take it out, have another try,
Maintenance intervals the insulator layer carefully. Blow it so as to ensure spark plug thread is
clean with compressed air; upper up to the standard of cylinder head
Replace it every 15000 km or half a
insulator layer should be cleaned, thread.
year.
too. · Tighten the spark plug with spanner;
Clean it every 5000 km or 3 months
Maintenance interval do not let it too tight.
15000km or 18 months Make sure spark plug cable is
installed in correct order. Clip the
Spark plug spark plug box aligned with the seat
Replacement of sparking plug
· Wipe any dirt and grease from the tightly.
Carbon, which forms on the sparking
cylinder head plug seats.
plug, will weaken the combustion
· Loosen the spark plug through
capacity of the sparking plug, so you Notice
pulling the spark plug box. Remove
- 118 -
Maintenance and Upkeep
The engine will work unsteadily and using high-tension line. 5. Do not use tension of drive belt can ensure
the components wll even be damaged spark plugs of any other else brands. normal working of engine, air
if the spark plugs are installed not 6. Do not pollute the spark plug hole. conditioning and other performance.
properly or spark plugs of any other 7. Pay attention to the safety, while Please replace the drive belt as soon
else brands are installed. In order to the engine is hot, the spark plugs are as possible, if it is worn, cracked or
avoid engine and other components hot, but you want to remove the inflated.
being damaged, the following tips plugs. In order to check tension of drive belt,
should be observed: 1. Tighten the press the middle of pulley properly
spark plugs according to standard Drive belt with your thumb to see whether or
torque, do not let it too tight, it will not the displacement of belt is about
damage the cylinder head thread if 10mm. If the belt is too loose, please
you let it too tight. 2. While have it adjusted and repaired by the
removing or tightening the spark nearest Chery Authorized Service
plugs, make the sockets aligned with Station.
the spark plugs rightly. 3. Install the
Notice
plugs in the engine and run them by Be sure not to start the engine while
hand at first. 4. Loosen the plugs checking the belt, otherwise it will
Correct installation and suitable cause moving parts squeezed,
through pulling them, instead of separated or twisted together. It may
- 119 -
Maintenance and Upkeep
cause personal injury, too. wiper blade in time, for outer dirt of
Wind shield wiper
them will obstruct the view. If the
Windshield washer fluid wiper blade cannot work normally,
It will broaden your field of version
please wash the window and wiper
and improve the driving safety
Please use appointed windshield blade with light cleanser first, then
greatly, if you use windshield wiper
washer fluid. wash them with clean water
correctly. Please check the wiper
Notice thoroughly. You had better use good
Washing system will do harm to the blade at regular intervals. Replace the
washer. If necessary, replace the
paint, therefore: 1.Do not use hardening, crisp or dirty blade if
anti-freezing fluid within the wiper blade. While replacing the
windshield washer. Do not mix water necessary.
with the detergent, water may be blade, press the blade holder, pull the
Because there is no ways to wipe the
cause the solution being frozen, wiper blade from the wiper arm, and
damaging the other components of silicone trace off the glass
the washing system.3. The washing then push the new one in directly.
successfully, do not use polishing
system may be damaged, if you do
not use appointed detergent. So compound on your vehicle
please use Chery recommended Notice
windscreen; polishing compound will
detergent. Solvent, fuel and paint diluent will all
produce strip trace, which influences damage the wiper blade, so you
should keep these matters away from
your field of version.
the wiper blade.
You should clean the window or
- 120 -
Maintenance and Upkeep
following matters: is poisonous, corrosive and
· Install battery firmly and surely. flammable, therefore: 1. Keep the fire,
· Keep the top of the battery clean spark and smoke away from the
and dry. battery. 2. Avoid spilling acid on any
· Keep connecting column and parts part of vehicle body, paint surface
clean and tight. and your clothing. 3. In order to
· If electrolyte leaks, please wash protect the environment, have the
Maintenane of battery with water and soda solution waste battery disposed by Chery
immediately. Authorized Service Station or place
· If you do not use the vehicle the waste battery on an appointed and
Different vehicle needs different
successively, disconnect the safe place. 4. Make the cable
battery. Your vehicle may be use
connecting column of battery, in connections in the right order, such as
low-maintenance battery, as well as
order to avoid battery discharging, corresponding connections of
non-lowmaintenance battery. So it is
you should charge the battery every 6 positive and negative ones; do not
necessary for you to check and
weeks. make mistakes. Failure to so so will
maintain the battery.
cause severe accident.
In order to maintain the battery
Notice
properly, pay attention to the
Batteries contain sulfuric acid which
- 121 -
Maintenance and Upkeep
firmly while driving on steep slope.If
Brake pedal Clutch pedal
the frequency of “click” you can
hear ,is less than the regulated
Check the free movement of the Clutch pedal does not have free
one,please have the hand brake
brake pedal. movement; if you feel it has, please
adjusted by Chery Authorized
Turn the engine off, step on the brake have it checked by Chery Authorized
Service Station or repair shop.
pedal for several times, so as to make Service Station or repair shop.
Travel There are 3-5 times of
the vacuum escape from the braking Maximum Pedal force
“click” under 20 kg force.
system. Press the brake pedal slightly travel
by hand, until you can feel slight 165mm 300N
resistance force. Measure the Ternary catalytic converter
movement distance of the brake
Hand brake
pedal. Please have it checked and Leaded gasoline is harmful to the
adjusted by the nearest Chery catalytic converter and electrical
You can check the hand brake
Authorized Service Station in time, if control sytem, so do not use leaded
travel,by means of recording the
the free movement of the brake pedal gasoline.
frequency of “click”,from releasing
does not accord with your driving In the case of vehicle with catalytic
position to applying totally
habit. converter, fuel filler port of fuel tank
position.You should apply hand brake
- 122 -
Maintenance and Upkeep
is too small for the leaded gasoline in good condition or any other Have all maintenance work done by
filler gun to insert. abnormal phenomenon indicating Chery Authorized Service Station.All
ignition system malfunction occurs, components of electrical control
you should drive at low engine system, injecting system and ignition
speed in a short time. system work normally, will reduce
emission pollution and extend
catalytic converter life.
Notice
You should avoid:
Do not use leaded gasoline, in order
· Frequently cold start the engine. Wheels and tires
to avoid damaging the catalytic
· Working hour of engine is too long,
converter.
while restarting (fuel injecting hour,
The catalytic converter and vehicle The manufacturer’s equipped tires fit
in starting stage, is postphoned)
may be damaged if you do not in with needs of the chasis, so as to
· The fuel tank becomes empty
observe the following tips: ensure the maximum
(abnormal fuel supply will result in
comfortableness and safety of driving.
engine overheated)
· If the engine can not start, the Using any other size or type of tires
· Start the engine by means of towing
engine works abnormally after or wheels may cause serious accident.
(unburn gasoline will enter the
cold starting, engine power is not Contact your Chery Authorized
catalytic converter)
- 123 -
Maintenance and Upkeep
Service Station for consultation and every two weeks at least. And do not hot. After checking, you should be
technical support, before you replace forget the spare! Check the tire sure to reinstall the tire inflation
with tires and wheels or any other pressures before a long journey, too! valve caps tightly.
type. The tire pressure should be checked Incorrect tire pressure may quicken
using an accurate tire pressure gauge, tire wear, reduce fuel economy and
Notice
Using any other size or type of tires when the tires are cold. make your vehicle less safe, easy and
may seriously affect handling comfortable to drive.
between the body and tires. So you
should be sure not to use tires of Tire pressure kpa (PSI) Low tire pressure results in tire
different size in one vehicle. Spare interior loss and possibility of
Condition Front Rear
tire blowouts or leak from over heated
Empty tires, while driving at high speed.
Tire inflating
load/Half 200 220 350 Hidden wound of tire cannot be
load eliminated through adjusting the
In order to make you comfortable and refilling pressures.
Full load 210 260 350
safe while driving, also in order to
extend tire life, it is necessary to keep
The pressure maybe fall blow the
the tire pressures at the proper level.
regulated minimum value; the
You should check the tire pressure
pressure will not fall when the tire is
- 124 -
Maintenance and Upkeep
whether or not they are damaged. If position will be shown through
Tire condition
any damage or abnormal wear is longitudinal marks of the tires.
found, contact your Chery For safety, we recommend you
It will cause tire hidden wound if you
Authorized Service Station for replace the tires if the tread
drive on the cliff border, you will find
consultation. longitudinal wear down below
it later, and the tire has the possibility
Abnormal wear is usually caused by approximate 1mm of indicator mark.
of leakage.
incorrect tire pressure, failure to Chery recommends at least both of
rotate tires, improper wheel the front or rear tires be replaced at a
You should be driving cautiously and
alignment, out-of-balance tires, time as a set. When replacing the tire,
slowly on uneven road surface (at a
severe braking and harmful driving use only the same size and
suitable angle if possible). Do not let
habit. construcion, same type and tread, as
the tires press concave and convex
The tires on your Chery have built-in originally installed.
edge, while you stop the car.
tread wear indicators to help you
Check the tires regularly for damage
know when the tires need
such as impurities, leakage, cuts
replacement. When the tread depth
splits and lateral convex, tire damage
wears to a certain degree, the
can result in the possibility of
indicator will appear in two or more
blowouts. Check the rims to see
adjacent grooves, the indicator’s
- 125 -
Maintenance and Upkeep
Exchange of tires
- 126 -
Maintenance and Upkeep
you use snow tires. You should use Don not use chains on the rear tires.
standard tires of same size and same Ignition system
model. As long as the road surface Retighten chains after driving
condition permits, do not use snow 0.5~1.0KM.
tires. Electronic ignition system has
Notice stronger energy than the conventional
Snow chain It may be disadvantageous for
ones; therefore, do not touch the
vehicle handling if you use snow
Regulations regarding the use of tire chain, so do not exceed 50km/h dangerous ignition components.
chains vary according to location or (30mph) or the chain manufacturer’s
recommended speed limit, whichever
type of road, so always check them is lower. If you hear the chain Central electronics box
before installing chains. touches the vehicle body or chasis,
you should stop the car and retighten
When installing chains on your tires, the chain as soon as possible. Drive
carefully you should follow the carefully avoiding sharp turns, bumps
and holes. You should avoid
instrucions of the chain manufacturer. locked-wheel braking; or observe
If wheel covers are used, they will be instrucions of the manufacturer.
Incorrect use of snow chain may
scratched by the chain band, so adversely affect vehicle handling
remove the covers before putting on between chain and body.
the chains.
Install the chains on the front tires.
- 127 -
Maintenance and Upkeep
Central electronics box is located in replace with a good one of same 10A 20A 30A
miscellany box rear part of the amperage.
15A 10A 10A
driver’s instrument panel. 5.Electrify the corresponding
The circuit all has fuse for protetion, equipment and check it. 15A 15A 20A
we recommend you carry some spare 6.Install the miscellany box properly. 10A 30A 30A
fuses to make things convenient for
Notice 15A 10A 10A
replacement. If the new fuse immediately blows
out, contact your nearest Chery 10A 20A 10A
Authorized Service Station for
Replacement of fuse assistance. Fuse is non-reusable, if
blown, it cannot be used again, do
not use the blown one for it will Engine compartment
1.Turn the engine and corresponding damage the electrical system.
- 128 -
Maintenance and Upkeep
engine rear part.
Fuse box
- 129 -
Maintenance and Upkeep
- 130 -
Car Light
- 131 -
Car Light
- 132 -
Car Light
1 High beam light/driving road lamp is in good condition), so as
(containing low beam light, Turn on the high beam headlights if 3 Front turn signal lamp
they are needed when driving at night,
It is convenient for other drivers to
for you to keep abreast of road
high beam light/driving light, know well your vehicle’s information,
condition at long distance, or for you
while you make a detour or make a
to meet another vehicle at short range,
turn.
while the visibility is not good, (the
and front turning lamp)
light flashes shortly while you meet
another one). Notice: Please let the front turn signal
lamp flash, while entering a crooked
road and cross roads, 50-100 meters
Notice: You should observe
ahead, it is convenient for drivers
corresponding traffic regulations.
behind you and pedestrian of either
side, know driving direction of your
Driving light is used at dusk,
Chery clearly, in order to avoid traffic
daybreak or in environment whose
accident.
visibility is not good.
- 133 -
Car Light
of penetrability, while the visibility is
not good (such as in bad fogs), it will Reversing The third brake
provide guarantee for you and other lamp lamp
people’s personal safety.
Rear brake
lamp
Rear fog
lamp
Notice: Check brake light to see if
Notice: Please use fog lamp there is any malfunction, before
correctly, according to the traffic driving in order to ensure you and
regulations. other people’s personal safety. Repair
or replace the damaged parts, in order
to avoid unnecessary traffic accident.
Brake lamp, the third brake lamp
In order to avoid unnecessary traffic
confusion, you can make use of rear Reversing lamp /vehicle plate
fog lamp to remind the other drivers Brake lamp is used to remind other
and pedestrian behind you of your drivers and pedestrian behind you to lamp
Chery’s information. make clear the road ahead.
The third brake lamp is used for Reversing lamp reminds other drivers
supplement. and pedestrian behind you, to know
- 134 -
Car Light
your Chery’s driving direction, in rear side know your driving direction. direction.
order to avoid unnecessary traffic
confusion.
- 135 -
In Case of an Emergency
- 136 -
In Case of an Emergency
a rubber ribbon. very jack; 3 Be sure not to start the
Tools in the trunk and spare tire engine after lifting the vehicle, in case
Tools in the trunk include jack, accident takes place; 4 Be sure to use
wheel spanner, screwdriver, open suitable bracket to support the vehicle
if you must work under the car.
wrench (10×13mm) and metallic hook
(used for disassemble wheel hood).
Telescopic Replacement of wheel
Type of jack
type
Maximum
1200kg Replacement of tires
working load
Please comply with the following tips
Type of grease Lithium in order to avoid unexpected
Tools in the trunk and spare tires are
placed in spare tire carrier under the accident while replacing tires:
luggage trunk bottom panel without ! Notice: - Move cautiously off the road to a safe
1 Be sure to make spare tire and tools
exception. place well away from the traffic.
in the trunk fixed properly, in order to
Spare tire is fastened under the avoid injury of occupants during - Park on a level place with firm
emergency braking or accident taking
bottom panel through a bolt. Tools in ground.
place; 2 Jack provided for this vehicle
the trunk are put in a fixed bracket to use is only applicable for this - Put the transmission in“P” position.
vehicle, be sure not to lift other
which is fixed on the spare tire through vehicles or heavy things else with this - Turn off ignition switch; pull out
- 137 -
In Case of an Emergency
ignition key. direction of the flat tire. Rotate
Procedures of replacement
- Turn on your emergency flashers, jack screw clockwise by hand,
firmly set the parking brake, if until jack top touches the vehicle
necessary, put into gear 1 or reverse bottom.
gear. Loosen Tighten
- Put a cuneiform spacer or something
can be used as obstacle to hold the
wheel, on the rear or front direction
of the wheel diagonally opposite the
- Pry off rim cap.
flat tire.
- Loosen every wheel bolt for one
- Set a warning triangular signpost, 10
circle with wheel spanner, but do
M away from the vehicle. Insert the jack handleinto the jack and
not remove the bolts yet, just
- Have everyone get out of the vehicle turn it clockwise, so as to raise vehicle,
unscrew them about one-half turn,
on the side away from traffic, to a until top of jack embeded in concave
before raising the wheels.
safe place. groove firmly and the wheels depart
- Position the jack at the correct
from the ground (about 3 CM).
jack point as shown. Put jack
verticallly close to front or back
- 138 -
In Case of an Emergency
Notice: Do not raise the vehicle too hand. Reinstall the wheel ornament
high - Rotate jack handle counter clockwise, If you fail to use the wheel bolts or
so as to make the vehicle come back to bolts not being tightened properly, will
the ground. lead to wheel too loose or being lost,
Descend
result in vehicle lose out of control.
Tighten the wheel bolts according to
“diagonal line” mode 1-2-3-4 , - Use suitable wheel bolts.
Ascend
shown as the following illustration. - Make sure the right position of
wheel bolts, and tighten the bolts
reliably.
4 1
As the jack touches the vehicle and - Do not smear oil or lubricating
begins to lift, double check that it is grease on the wheel bolts.
properly positioned in case of slipery.
Notice:
-Turn the wheel set bolts counter
2 The vehicle may be unstable, even has
clockwise, so as to remove the bolts, 3
possibility of accident while using jack,
and then remove the wheel.
therefore: 1. you should put the jack on
- Install the spare tires properly;
right jacking point .2. Make the jack
tighten the wheel bolts clockwise by
- 139 -
In Case of an Emergency
vertical to the ground while installing place to replace the tires. you should pay attention to the
the jack. 3. Never get beneath the Warm hints: If you are not sure to following matters:
vehicle when supported by a jack, do replace the tire safely, please contact
not start or run the engine while your the nearest Chery Authorized Service - Do not make battery close to fire
vehicle is supported by a jack. 4. Have Station for assistance. or spark.
the occupants get out of the vehicle on - Avoid spilling battery acid on
the side away from traffic, in a safe Jump starting the engine your eyes, skin, clothing or
place. 5. Jack is only used for vehicle for electrolyte of battery
replacement of wheel. 6. Do not contain sulfuric acid, which will
If the battery is flat, you can make use
support the vehicle using jack on bevel result in injury if you touch it
of power of other vehicle’s battery to
or slipery surface. 7. You should directly.
start the engine.
position the jack on side which is the - Make sure that voltage of battery
closest to the flat fire, at the same time; which helps you to start the
Any incorrect operation will result in
hold the diagonal wheel opposite to the engine is the same as voltage of
battery explosion, causing personal
flat tire. 8. Make sure parking brake is your vehicle battery (12V).
injury or property loss, furthermore,
on, before supporting, put transmission - Do not disconnect battery while it
electrical system of vehicle will be
on gear 1 or reverse gear if necessary. is low but not flat.
damaged to some extent, and therefore
9. Keep away from the heavy traffic - Shut all unnecessary load of
- 140 -
In Case of an Emergency
electrical appliance. but not flat. Vehicle engine which provide jump
- Don’t touch the battery while · Connect one end of the second starting can be normally working
jump starting. jumper cable to the negative (-) on during period of jump starting.
- Do not make two conducting booster battery. Start the vehicle whose battery is flat
wires which help to start, short · Connect the other end of second within on e minute as possible as you
connect. jumper cable to engine block of other can,lasting time shall be within 12
- Pull parking brake, place gear bar vehicle or bot connecting wire which seconds.You shall disconnect the
to neutral gear. is supported by the engine. connection without delay after starting.
Notice;
Jump starting procedure: Do not connect the jumper cable to Turn off all lights and accessories
Connect one end of the first jumper negative connecting wire column of while jump starting the engine, in
order to avoid other systems or
cable to the positive (Marked with “+” flat battery. components being damaged, do not
on outershell of battery of connecting The recommended connecting point start your vehicle by means of pushing
and pulling,to do so,maybe damage
wire column which helps to start the shall be far away from the flat battery ternary catalytic converter and other
engine) as possible as you can. electrical components.
·Connect the other end of the first Make the jumper cable aligned in
jumper cable to positive “+” marking order to avoid touching the adjustable
on outer shell of battery which is low components in engine room.
- 141 -
In Case of an Emergency
Notice: Open the hook cover.
Towing vehicle Never tow from the rear with the front
wheels on the ground, for this may
cause serious damage to the
If towing is necessary. We recommend transmission. Therefore you should
you contact your nearest Chery adopt lifting front wheels to tow the
Authorized Service Station or vehicle. The vehicle can be towed by
Professional Rescue Centre for means of sling transportation
assistance. Towing hook cover
equipment, use flat board or wheel as
It is necessary for you to follow lifting auxiliary equipment.
appropriate lifting and towing
procedures, in order to avoid damage - Buckle the cable tightly on the
to your vehicle. When towing with Emergency towing towing hook.
wheel lift type truck, you should:
-Turn on the warning light of the two
vehicles.
- Put the ignition switch on “I” While emergent towing, it is possible
position. to use towing auxiliary equipment.
- Put the gear bar on neutral gear
position. There is a towing hook in your vehicle
·Release the parking brake. which is mounted on the bumper of
·The vehicle should be towed under the front and rear part of vehicle. Front towing hook
circumstances of driving wheel
(front wheel) depart from the While towing the vehicle with towing -Turn the warning lights of the two
ground. hook and cable: vehicles on.
- 142 -
In Case of an Emergency
-Put gear lever to neutral gear position, fixed on the towing hook tightly. Pull
the towing cable to check if it is tight
release parking brake. enough.
-Place ignition switch on “II” position, 3. Use rear towing hook to tow other
vehicles.
so as to loosen lock of steering bearing,
make brake lamp horn and windshield
Save yourself after being
window wiper normally working.
-Only driver can be in the vehicle to
caught in spongy ground
steer it and operate the brakes.
- Shut window of vehicle being towed, When your vehicle is troublesome for
turn on button of interior circulation it being caught in spongy pit, at this
time, it is necessary for you to rock the
mode, in order to avoid exhausted gas vehicle in order to escape from the
Notice:
gets in. The vehicle may lose control while hazard, please shift gear 1 to reverse
gear, and then shift reverse gear to gear
- Avoid sudden starting or bumping being towed. Therefore, if transmission,
1repeatedly. At the same time, step on
axles, steering or brakes are damaged,
and vibration. the accelerator gently.
please do not tow the vehicle. At the
Do not make the engine idling, so as to
same time, pay attention to the
avoid damaging other components,
following matters:
because of engine being overheated.
1. Do not pull out ignition key for it
will lock the steering system and make You should ask for rescue if you fail to
vehicle unable to move. save yourself.
2. Make sure two ends of towing cable
- 143 -
In Case of an Emergency
Notice:
The vehicle may be caught while
driving on snow, sand or mud field.
Under this circumstance, idling engine
will damage the driving elements;
therefore, do not drive your vehicle at
high speed.
- 144 -
Technical Requirements and Data
- 145 -
Technical Requirements and Data
Oils for vehicle use:
Engine oil
Oil viscosity for this vehicle use is 10W-30 (not lower than grade SG); selected oil viscosity for vehicle use in winter is 5W-30
(not lower than grade SG).
We recommend shell brand engine oil according to the actual condition in China at present.
Don’t confuse engine oil of different brands from different manufacturers together.
Please select suitable engine oil according to recommended one and actual conditions as possible as you can.
Failure to do so will result in engine being over worn or other more severe malfunction.
Fuel
You should select premium unleaded gasoline with a Research Octane Number of 93 or higher for optimum engine performance
for this vehicle to use.
It is sure to hasten life of engine if you select gasoline with low octane number or gasoline of poor quality.
Transmission gear oil
Transmission gear oil for this vehicle to use: for manual transmission is GL-4, SAE 75W-90 or Fuchs 75V, do not confuse gear
oil of different brands together.
Coolant
Recommended by the User’s Manul for this vehicle, we select coolant of ESSEX or Shell brand. Soft and hard water are
forbidden to use as coolant.
- 146 -
Technical Requirements and Data
Dimension of vehicle
- 147 -
Technical Requirements and Data
Parameters of engine
Paramenters of performance
Rated power kw 65 65 85
- 148 -
Technical Requirements and Data
Wheel
- 149 -
Technical Requirements and Data
Tire pressure
kPa
Item Front Rear Spare Small spare
Empty load/Half 200 220 350 420
load
Full load 210 260 350 420
Notice:
You should check the tire pressures at least once a month; tire pressure is especially important while
high-speed driving.
Pressure values listed in the schedule are appliable for cold tire pressure; it is not necessary to reduce the
pressure if the pressure slightly goes up while tire being heated.
- 150 -
Technical Requirements and Data
Official VIN of vehicle
Engine No. Vehicle data plate
VIN CODE
- 151 -