Professional Documents
Culture Documents
Side Scan Manual
Side Scan Manual
Symptom (public)
Problem (public)
This FAQ describes the steps to manually tune a C-Nav GPS/GNSS receiver to an
alternate C-Nav Corrections Satellite frequency using C-Nav controller
software and display units.
Functionality has been added to update the list of available C-Nav Corrections
Satellites via a small configuration file (SATDEFS). This allows the operator
to simply select an appropriate C-Nav Corrections Satellite from a list rather
than manually defining one. This is especially useful for discontinued
products such as C-Nav2000, C-Nav1010, and C-Nav2050 receivers. Please refer
to the FAQ, [1]How to load a SATDEFS configuration file? for instructions.
[1] https://faq.cnav.com/otrs/public.pl?Action=PublicFAQZoom;ItemID=45
Solution (public)
No longer in service
The above table lists the current and new frequencies for the C-Nav
Corrections Satellite.
C-Nav3050
C-Monitor or C-Setup
- Go to the Corrections Receiver page under the Device menu.
- Press the Settings button.
- Press the Custom Satellite Operations button.
- Enter the desired Satellite ID and Satellite Frequency.
- Press the Define Satellite button then Close.
- Highlight the newly defined satellite in the Available Satellites list and
press the Apply button to save the settings.
- Press the Status button to return to the Downlink Status section.
- After a few moments, verify Signal Status reads "Locked".
C-NaviGator
- Go to the Corrections Receiver page under the Device menu.
- Press the Settings button.
- Press the Custom Satellite Operations button.
- Enter the desired Satellite ID and Satellite Frequency.
https://cnavotrs.cnav.com/otrs/public.pl?Action=PublicFAQPrint;ItemID=29 Page 1
FAQ#110029
C-Nav2050
C-Monitor or C-Setup
- Go to the Corrections Receiver page under the Device menu.
- Press the Select Satellite button.
- Using the drop-down list, select "Custom".
- Enter the desired Satellite ID and Satellite Frequency.
- Press Apply to save the settings.
- Press the Status button to return to the downlink information page.
- After a few moments, verify lock in the Downlink Status section.
C-NaviGator I & II
- Go to the Corrections Receiver page under the Device menu.
- Press the Select Satellite button.
- Using the drop-down list, select "Custom".
- Enter the desired Satellite ID and Satellite Frequency.
- Press Apply to save the settings.
- After a few moments, verify lock in the Downlink Status section.
C-NaviGator III
- Go to the Corrections Receiver page under the Device menu.
- Press the Select Satellite button.
- Using the drop-down list, select "Custom".
- Enter the desired Satellite ID and Satellite Frequency.
- Press Apply to save the settings.
- Press the Status button to return to the downlink information page.
- After a few moments, verify lock in the Downlink Status section.
C-Nav1010
C-Monitor or C-Setup
- Go to the Corrections Receiver page under the Device menu.
- Press the Select Satellite button.
- Using the drop-down list, select "Custom".
- Enter the desired Satellite ID and Satellite Frequency.
- Press Apply to save the settings.
- Press the Status button to return to the downlink information page.
- After a few moments, verify lock in the Downlink Status section.
C-NaviGator I & II
- Go to the Corrections Receiver page under the Device menu.
- Press the Select Satellite button.
- Using the drop-down list, select "Custom".
- Enter the desired Satellite ID and Satellite Frequency.
- Press Apply to save the settings.
- After a few moments, verify lock in the Downlink Status section.
C-NaviGator III
- Go to the Corrections Receiver page under the Device menu.
- Press the Select Satellite button.
- Using the drop-down list, select "Custom".
- Enter the desired Satellite ID and Satellite Frequency.
- Press Apply to save the settings.
- Press the Status button to return to the downlink information page.
- After a few moments, verify lock in the Downlink Status section.
C-Nav2000
C-Monitor or C-Setup
- Go to the Corrections Receiver page under the Device menu.
- In the Corrections Satellite section, use the drop-down list to select
"Custom".
- Enter the desired satellite frequency.
- Press Apply to save the settings.
- Verify lock in the Downlink Status section.
C-NaviGator
- Go to the Corrections Receiver page under the Device menu.
- In the Corrections Satellite section, use the drop-down list to select
"Custom".
- Enter the desired satellite frequency.
- Press Apply to save the settings.
- Verify lock in the Downlink Status section.
https://cnavotrs.cnav.com/otrs/public.pl?Action=PublicFAQPrint;ItemID=29 Page 2