Professional Documents
Culture Documents
CONTROL PANEL
1. ON/OFF button
2. START/PAUSE button with indicator light 1 2 3 4 5
3. WASH CYCLE PROGRESS indicator lights
4. DOOR LOCKED indicator light
5. STAIN REMOVAL button with indicator lights
6. FUNCTION buttons with indicator lights
7. DRYING ONLY button with indicator
light
8. DRYING LEVELS button
9. TIME DRYING button
10. TEMPERATURE button
11. WASH CYCLE knob 11 10 9 8 7 6
WASH CYCLE TABLE
Maximum load 7 kg Detergents and Recommended
Power input in off mode 0.5 W / in left-on mode 8 W Additives detergent
Maximum Fabric
Max. load for Max. load for Duration
Drying
Temperature Wash softener
Wash cycle spin wash cycle (kg) drying cycle Powder Liquid
(kg) (Minutes)
Default Range (r.p.m.) 2 3
1 Daily Mix Wash & Dry 40 °C - 40 °C 800 3,5 3,5 265 –
2 Shirts & T-Shirts 40 °C - 40 °C 1000 2,0 2,0 180 –
3 Pre Iron – – – 1,5 – 20 – – – – –
4 Steam Refresh – – – 1,5 – 20 – – – – –
5 Cotton (2) 40 °C - 60 °C 1200 7,0 5,0 230
6 Synthetics 40 °C - 60 °C 1200 4,0 3,5 195
7 Anti Stain Quick 40 °C - 40 °C 1200 3,5 3,0 45 –
8 Anti Stain 100 40 °C - 40 °C 1200 7,0 5,0 205 –
9 White (3) 60 °C - 90 °C 1200 7,0 5,0 140 –
60° C 1200 7,0 5,0 210
10 Eco Cotton 60°/40° (1) 60 °C
40°C 1200 7,0 5,0 230
11 Coloureds 40 °C - 40 °C 1200 7,0 5,0 100 –
12 Ultradelicates 30 °C - 30 °C - 1,0 1,0 80 –
13 Wool 40 °C - 40 °C 800 1,5 1,5 75 –
14 Fast 30' 30 °C - 30 °C 800 3,0 - 30 – –
Rinse+Spin – – 1200 7,0 5,0 50 – – –
Spin & Drain – – 1200 7,0 5,0 10 – – – –
Required dosage Optional dosage
The cycle duration indicated on the display or instruction manual is an estimate based on For all testing institutes:
standard conditions. The actual duration may vary in relation to several factors, such as 2) Long cotton cycle: set cycle 5 at a temperature of 40°C.
the temperature and pressure of the incoming water, ambient temperature, amount of 3) To run the regulatory cycle according to UAE.S5010-2: 2019, select the Cotton cycle in
detergent, load quantity and type, load balancing and any additional options selected. position 9 using the temperature at 60 ° C
1) Test programme in compliance with standard EN 50229 (Wash):
This cycle is designed for normally soiled cotton loads and is the most efficient in terms of
both electricity and water consumption; it should be used for garments washable at 60°C or
at 40°C. The actual washing temperature may differ from the indicated value.
Test programme in compliance with standard EN 50229 (Drying): select the 10 wash
programme and set the drying level to “ ”, for both loads. The first drying cycle must be
carried out with the nominal load.
The washer-dryer does not The appliance is not plugged into the socket, or not sufficiently to make contact.
start. There is no power in the house.
The washer-dryer door is not closed properly.
The ON/OFF button has not been pressed.
The wash cycle does not start. The START/PAUSE button has not been pressed.
The water tap has not been opened.
A delay has been set for the start time.
The water inlet hose is not connected to the tap.
The hose is bent.
The machine does not fill with
water or the indicator light The water tap has not been opened.
for the first wash cycle stage There is no water supply in the house.
flashes rapidly.
The pressure is too low.
The START/PAUSE button has not been pressed.
The drain hose is not fitted between 65 and 100 cm from the floor.
The free end of the hose is immersed in water.
The washer-dryer The wall drainage system does not have a breather pipe.
continuously loads and
unloads water. If the problem persists even after these checks, turn off the water tap, switch the appliance off and contact the
Technical Assistance Service. If the home is on one of the upper floors of a building, there may be problems relating
to back-siphonage, causing the washer-dryer to fill with water and drain continuously. Special anti-siphon valves
are available in shops and help to prevent this inconvenience.
The cycle does not include drainage: with certain cycles it must be started manually.
The washer-dryer does not
The drain hose is bent.
drain or spin.
The drainage duct is clogged.
The drum was not unlocked correctly during installation.
The washer-dryer vibrates a
The washer-dryer is not level.
lot during the spin cycle.
The washer-dryer is tucked between furniture cabinets and the wall.
The water inlet hose is not screwed on properly.
The washer-dryer leaks. The detergent dispenser drawer is obstructed.
The drain hose is not properly attached.
The “Options” lights and the
START/PAUSE indicator light
flash while one of the wash Switch off the machine and unplug it, wait for approximately 1 minute and then switch it back on again.
cycle progress and DOOR If the problem persists, contact the Technical Assistance Service .
LOCKED lights are lit in a fixed
manner.
The detergent is not suitable for machine washing (it should be marked with “for washer-dryer use” or “hand wash
There is too much foam. and machine wash” or similar).
Too much detergent was used.
The appliance is not plugged into the socket, or not enough to make contact.
The washer-dryer does not There has been a power failure.
dry. The appliance door is not shut properly.
DRYING is in the OFF position.
You can download the Safety Instructions, User Manual, Product Fiche and Energy data by: xxxxxxxxxxxx xxxx
• Visiting our website - http://aristonchannel.com
• Using QR Code
• Alternatively, contact our technical Assistance Service (See phone number in the warranty booklet). When
contacting our After‑sales Service, please state the codes provided on your product’s identification plate.