Professional Documents
Culture Documents
ToymakingPlans.com © 2013
Design by
Nemanja Stojanovic
2 ToymakingPlans.com © 2013
Warning: Read before copying. SCROLL SAW MAGIC
The unauthorized reproduction or
distribution of this copyrighted work is P-51 Mustang Airplane
illegal. Criminal copyright infringement
Build the entire airplane with just a
including infringement without scroll saw and power drill!
monetary gain, is investigated by the
FBI and is punishable by up to 5 years
in federal prison and a fine of $250,000.
Email: support@toymakingplans.com
FULL-SIZE WOOD TOY PLAN SET
©2013 ToymakingPlans.com - All rights reserved - 030814 P-51 Mustang Photo Pictorials........................................... 4-9
Note to the Readers: Due to different conditions, tools, and individual P-51 Mustang Parts Index & How-To’s........................... 10-13
skills, ToymakingPlans.com assumes no responsibility for any
damages, injuries suffered, or losses incurred as a result of following
P-51 Mustang Plan Views.............................................. 14-21
the information published in this plan set. Before beginning any project
review instructions carefully. If any doubts or questions remain consult
local experts or authorities. P-51 Mustang Precision Patterns....................... 17 and 22-25
Copyright Information: Plans and patterns in this Plan Set can be Gift and Shows Cartoning Information................................ 26
photo-copied for personal use when building the toys. ToymakingPlans.
com plans and patterns are copyrighted and cannot be distributed or Printable Box Label with Signature Line......................... 27-28
shared for free or for any other reason.
Printable Color Photo Gallery......................................... 29-39
ToymakingPlans.com © 2013 3
SCROLL SAW MAGIC
P-51 MUSTANG AIRPLANE
Design by
Nemanja Stojanovic
Painted P-51 Mustang is built with fine-grained poplar for the smoothest finish. Finish is spray can Krylon or Rust-Oleum
white primer and color glosses. Krylon brush-on Color Creations also works well. With both types of paint, apply 2 coats
of primer sanding each coat with 220 sandpaper when dry. Apply 3 coats of color sanding with 400 sandpaper when dry.
To view page 4-5 as a two-page spread in Adobe Reader:
Apply final coat of Krylon Triple Thick Clear. All Krylon and Rust-Oleum paints and finishes are non-toxic when dry.
1. Select View/Page Display/Two Page Scrolling
2. Select View/Page Display/Show Cover Page in Two Page View
ToymakingPlans.com © 2013 5
SCROLL SAW MAGIC
P-51 MUSTANG AIRPLANE
Design by
Nemanja Stojanovic
6 ToymakingPlans.com © 2013
SCROLL SAW MAGIC
P-51 MUSTANG AIRPLANE
Design by
Nemanja Stojanovic
ToymakingPlans.com © 2013 7
SCROLL SAW MAGIC
P-51 MUSTANG AIRPLANE
Design by
Nemanja Stojanovic
8 ToymakingPlans.com © 2013
SCROLL SAW MAGIC
P-51 MUSTANG AIRPLANE
Design by
Nemanja Stojanovic
ToymakingPlans.com © 2013 9
SCROLL SAW MAGIC
P-51 MUSTANG AIRPLANE
pages 22-23 pages 24-25
8
5 6
1
3
9
4
4
10
7
1 3
2 6
12
14 13
Top
11
Plan View
Side Bottom
Plan View Plan View
PARTS INDEX
1. 1/4” x 2-5/16” x 10-1/2” make 2
2. 1/4” x 2-9/16” x 5-15/16” make 1
3. 1/4” x 2-1/8” x 8-9/16” make 2
4. 1/4” x 1-1/2” x 4-3/4” make 1 4-7/16” HIGH X 13-3/8” WIDE
5. 1/4” x 2-3/8” x 3-1/8” make 1 X 11-7/8” LONG
6. 1/4” x 3-3/8” x 6-3/16” make 2
7. 7/8” x 1” x 2-7/8” make 1 Part 10:
8. 1/4” x 7/8” x 1-1/2” make 2 craftparts.com
9. 1” dia. x 1/4” make 2 # AP1010
10. craftparts.com axle pin buy 2 1-3/8” Axle Pegs w/
11. 1/4” x 3-3/4” x 3-3/4” (pg 17) make 1 15/64” tenon
12. 5/16” dia. x 1” make 1 Head diameter - 3/8”
13. 7/8” dia. x 9/16” make 1 Cut tenon to 1/2”
14. 3/16” x 1/4” x 1-1/2” make 2 length
10 ToymakingPlans.com © 2013
SCROLL SAW MAGIC
P-51 MUSTANG AIRPLANE
4
6
7
14
3
11
12
14
13
10
2
8
9
9
8
ToymakingPlans.com © 2013 11
SCROLL SAW MAGIC
P-51 MUSTANG AIRPLANE Step 1 Assembly
1 3
2
Wing
Slot Step 2 Assembly
1 Wing
Slot 3
Wing Slot
1. Refer to Plan Views on pages 14-21 as a guide to 2. Refer to Plan Views on pages 14-21 as a guide to 3. Refer to Plan Views on pages 14-21 as a guide to
clamp and glue two Part 1’s together. Assemble with clamp and glue the one Part 2 to the Step 1 Assembly. clamp and glue two Part 3’s to the Step 2 Assembly.
Elmer’s or TiteBond woodworker’s glue. The two Part Assemble with Elmer’s or TiteBond woodworker’s Assemble with Elmer’s or TiteBond woodworker’s glue.
1’s are aligned with edges and with the wing slot cutout glue. Part 2 is at right angles to Step 1 Assembly and The two Part 3’s are aligned with the wing slot of the
area of Part 1. Let the glue dry thoroughly before centered left to right on Step 1 Assembly. Let the glue Step 2 Assembly. Let the glue dry thoroughly before
proceeding. dry thoroughly before proceeding. proceeding.
6
2
4. Refer to Plan Views on pages 14-21 as a guide to 5. Refer to Plan Views on pages 14-21 as a guide to 6. Refer to Plan Views on pages 14-21 as a guide to
clamp and glue Part 4 to the Step 3 Assembly. Part 2 is clamp and glue Part 5 to the Step 4 Assembly. Part clamp and glue two Part 6’s to the Step 5 Assembly and
at right angles to Step 3 Assembly and centered left to 5 is at right angles to Step 4 Assembly and centered to the top sides of the two Part 2’s. The two Part 6’s
right on Step 3 Assembly. Let the glue dry thoroughly left to right on Step 4 Assembly. Let the glue dry are at right angles to Step 5 Assembly. Let the glue dry
before proceeding. thoroughly before proceeding. thoroughly.
12 ToymakingPlans.com © 2013
SCROLL SAW MAGIC
Step 7 Assembly P-51 MUSTANG AIRPLANE
7
10
8 9
8 9
Step 6 Assembly 10
Step 8 Assembly
7. Refer to Plan Views on pages 14-21 as a guide 8. Refer to Plan Views on pages 14-21 as a guide to 9. The two wheels Part 9 are held in place with the two
to clamp and glue Part 7 to the Step 6 Assembly. clamp and glue two Part 8’s to the Step 1 Assembly. axle pins Part 10. The axle pins glue into the two Part
Assemble with Elmer’s or TiteBond woodworker’s glue. Assemble with Elmer’s or TiteBond woodworker’s 8’s of the Step 8 Assembly allowing the wheels Part 9
Part 7 is centered left to right on the Step 6 Assembly. glue. The two Part 8’s fit tightly into slots in Part 2. Let to rotate freely on axle pins Part 10. Let glue dry before
Let the glue dry thoroughly before proceeding. the glue dry thoroughly before proceeding. proceeding.
Step 10 Assembly
Step 11 Assembly
12
14
12 14
Step 9 Assembly 13 11
10. Refer to Plan Views on pages 14-21 as a guide 11. Refer to Plan Views on pages 14-15 to clamp The P-51 Mustang shown above is finished with 3
to clamp and glue Part 12 to the Step 9 Assembly. and glue two Part 14’s to the Step 10 Assembly. Slide coats of gloss polyurethane clear water-based finish.
Assemble with Elmer’s or TiteBond woodworker’s glue. Part 11 onto Part 12 then glue Part 13 to Part 12 in The first two coats of clear have been sanded with 220
Let the glue dry thoroughly before proceeding. a position that allows the propeller Part 11 to rotate grit sandpaper. The third coat of clear is not sanded.
freely on Part 12. Polyurethanes manufactured in the USA are non-toxic
when dry and are safe for children of all ages. 13
ToymakingPlans.com © 2013
SCROLL SAW MAGIC
P-51 MUSTANG AIRPLANE
14 ToymakingPlans.com © 2013
SCROLL SAW MAGIC
P-51 MUSTANG AIRPLANE
ToymakingPlans.com © 2013 15
SCROLL SAW MAGIC ACTUAL SIZE
P-51 MUSTANG AIRPLANE 0 printer scale 1 2 3
A
ATTENTION: THE FULL SIZE PRECISION
PLAN VIEW IS FOR ASSEMBLY REFERENCE.
INDIVIDUAL PATTERNS ON PAGES 17, 22-25.
12
13
8
14 3
1 7
10
1
1
6
2
8 3
B
5
Front View
6
1 1 2
3 3
8
10
5
11
Top View
6
1
3 1
18 ToymakingPlans.com © 2013
SCROLL SAW MAGIC
ACTUAL SIZE 0 printer scale 1 2 3 P-51 MUSTANG AIRPLANE
B
11
13
14
Bottom View
14
1
IMPORTANT NOTE: To print 1
3 10
out enough paper patterns for
9
the plan set from your computer 8
printer print only the precision line 3
patterns you need for each project.
The pages are all line drawings 6
in black to conserve printer ink.
Check your printer printed size
accuracy by measuring printer
scale on each pattern with a ruler.
If printed size of pattern is not
100% adjust printer settings.
8
9
ATTENTION: THE FULL SIZE PRECISION
10
PLAN VIEW IS FOR ASSEMBLY REFERENCE.
INDIVIDUAL PATTERNS ON PAGES 17, 22-25.
2 1
1
3
ToymakingPlans.com © 2013 19
SCROLL SAW MAGIC ACTUAL SIZE
P-51 MUSTANG AIRPLANE 0 printer scale 1 2 3
Top View
IMPORTANT NOTE: 14
1
To print out enough paper
1
patterns for the plan set from 3
your computer printer print
only the precision line patterns
you need for each project. The
3
pages are all line drawings in
black to conserve printer ink. 14
Check your printer printed
size accuracy by measuring
printer scale on each pattern
with a ruler. If printed size of 13
pattern is not 100% adjust
printer settings.
6 11
20 ToymakingPlans.com © 2013
SCROLL SAW MAGIC
ACTUAL SIZE 0 printer scale 1 2 3 P-51 MUSTANG AIRPLANE
Bottom View 3
5
4
D
ToymakingPlans.com © 2013 21
SCROLL SAW MAGIC ACTUAL SIZE
P-51 MUSTANG AIRPLANE 0 printer scale 1 2 3
IMPORTANT NOTE: To print out enough paper patterns for the plan
set from your computer printer print only the precision line patterns
you need for each project. The pages are all line drawings in black to
conserve printer ink. Check your printer printed size accuracy by
measuring printer scale on each pattern with a ruler. If printed size of
pattern is not 100% adjust printer settings.
4
1. 1/4” x 2-5/16” x 10-9/16” make 2
22 ToymakingPlans.com © 2013
SCROLL SAW MAGIC
ACTUAL SIZE 0 printer scale 1 2 3 P-51 MUSTANG AIRPLANE
5/16” hole
1
1/2” deep
2
NOTE: Drill after two Part 1’s
are glued together.
ToymakingPlans.com © 2013 23
SCROLL SAW MAGIC ACTUAL SIZE
P-51 MUSTANG AIRPLANE 0 printer scale 1 2 3
IMPORTANT NOTE: To print out enough paper patterns for the plan set from your computer printer print only the
precision line patterns you need for each project. The pages are all line drawings in black to conserve printer ink.
Check your printer printed size accuracy by measuring printer scale on each pattern with a ruler. If printed size
of pattern is not 100% adjust printer settings.
24 ToymakingPlans.com © 2013
SCROLL SAW MAGIC
ACTUAL SIZE 0 printer scale 1 2 3 P-51 MUSTANG AIRPLANE
1/4” 1/4”
hole hole
thru thru
6
5/16” hole
6 x 1/4” deep
6. 1/4” x 3-3/8” x 6-3/16” make 2
12
13
12. 5/16” dia. x 1”
make 1
13. 7/8” dia. x 9/16” make 1
Cut Part 13 from 7/8” dowel: Drill hole before
14 14
shaping part. Place Part 13 in power drill chuck
and spin-sand Part 13 to shape with hand-held
block sander.
14. 3/16” x 1/4” x 1-1/2” make 2 ToymakingPlans.com © 2013 25
Offer your P-51 Mustang Fighter Airplane
in quality Gift Boxes.
Add a pro-touch to your P-51 Mustang Wood toy
masterpieces with a labeled and signatured gift box.
The airplane fits comfortably in this off-the-shelf
corrugate carton available at www.uline.com. It’s
easy to order online and in quantities as small as 25
cartons. The cartons are delivered to your door in 3
to 5 days.
26
P-51 Mustang
Fighter Airplane
4-7/16” HIGH X 13-3/16”
WIDE X 11-7/8” LONG
27
P-51 Mustang
Fighter Airplane
4-7/16” HIGH X 13-3/16”
WIDE X 11-7/8” LONG
28
34 ToymakingPlans.com © 2013
ToymakingPlans.com © 2013 35