Professional Documents
Culture Documents
1
Content
1.SIGNAL LINES....................................................................................................................................................... 4
4. CONVERTER PICTURE.....................................................................................................................................14
6. ALARM INFORMATION...................................................................................................................................20
7. TROUBLESHOOTING.............................................................................................................................................21
7.1 NO DISPLAY...................................................................................................................................................... 21
7.2 EXCITING ALARM.............................................................................................................................................. 21
7.3 EMPTY PIPE ALARM........................................................................................................................................... 21
7.4 FLOW MEASUREMENT INACCURACIES...............................................................................................................22
APPENDIX 1.............................................................................................................................................................22
2
APPENDIX 2 MENU CHART............................................................................................................................. 23
3
L-mag D Electromagnetic flow meter Converter Operation
1.Signal Lines
1.1Labels and connection of signal lines
Signal Line:
1.2Terminal Wiring
4
1.2 Terminal Wiring
K:
OFF:Not connect
Noted:Terminal Resistance is used for long distance communication only. If for short distance,do not connect.
Contact area of copper Connector PE on Converter Cabinet for grounding should be larger than
Secondly,weld the red copper wire to the tent peg, and finally connect the grounding wire to the sensor
flange,ground ring,pipe flange. Please check Chart 1.3.
Noted:Please use stainless steel material to fix the screw,spring washer,flat gasket.
5
Chart 1.3 Converter Grounding Diagram
2. Parameter Setting
2.1Flow setup
2.1.1 Flow Unit Flow Unit is selectable in flow parameter:L/s、L/m、L/h、m3/s、m3/m、m3/h;
2.1.2 Flow Total Unit
Converter display is counter with 9 bits, and the max is 999999999.
electromagnetic flow meters converters to make sure all the instruments can interchange by 0.1%.
When FS is not “0”, make FS = 0. Note: if change the value on next line and FS increases, please change the
6
“+, -” to correct FS to zero.
Flow zero is the compound value of the sensor, and should be recorded in sensor list and band. The unit will
Signals of flow volume, velocity and percentage out of displaying and outputting them. Sometimes user can
delete output of current output signal and frequency (pulse) output signal only to have flow, velocity and
If users think the direct and design are differ, just change the direct parameter is OK, but not change exciting
or signal.
2.1.8 Flow Filter Time
It means time of filter measure value. The long one can enhance the stability of flow display and output
digital, and fits for gross add up of pulse flow; the short one means fast respond rate, and fits for production
and makes the relation of percent display, frequency output and current output with flow:
current output = ( flow measure / measure range) * current full + base point;
“disable”, the sensor will export pulse as “0” and current as “0”(4mA or 0mA) for the flow flows reversals.
numerical value.When the value of flow percentage is larger than the value of setting value, the converter
7
outputs the alarm signal.
2.2.3 Snsr MT Range
When actual MT value is too small, user can adjust the empty pipe range. While doing this,please make sure
Upper Line:MR stand for the measure value of the empty pipe range.
If increase modified value on the below line, MR will increase; If decrease modified value on the below
line,MR will decrease. User can adjust MR to a suitable value( suggest to adjust to around MR=500),then
easily. The parameter displayed upper line is real MTP, and the parameter displayed bellow is the “Snsr MT
alarm” that should be set. When setting “Snsr MT alarm”, you could be according to the real MTP, the value
Upper Line: MZ standard for the measure value of empty pipe zero point
Below Line: Modified value of empty pipe zero point
Firstly,according to the actual MT value,adjust the modified value to make MZ=5~10 around (Noted:If add
below line modified value,MZ value will be smaller).
2.2.5 Snsr MT alarm
When the pipe is full of liquid (whether flowing or not), the parameter displayed upper line is real MTP, and
the parameter displayed below is the “Snsr MT alarm” that should be set. When setting “Snsr MT alarm”, you
could be according to the real MTP, the value that should be set is usually three to five times of real MTP
2.2.6 .Snsr measure Ena.
The state of empty pipe can be detected with the function of converter and do not need additional electrode. If
user select System alarm enable,then when the fluid is lower than electrode, the flow meter can detect as
8
empty pipe state.If the pipe is empty, the signals of analog output and digital output would be zero and
20mA output.
2.3.4 Analog Zero CRC
Adjust analog output zero point,to accurate at 4mA.
2.3.5 Analog Output
Analog Output type: 4~20mA.
2.3.6 Pulse Output
Two kinds of Pulse Outputs are can be chosen: Frequency Output and Pulse Output. Frequency Output is
continuous square waveform and Pulse output is a serial wave of square wave. Frequency output is mainly
used for instant flow and total integrated flow in short time measurement. Frequency output can be chosen in
equivalent frequency unit and volume of integrated flow can be displayed. Frequency Output can be used in
long time measurement for total integrated flow with volume units.
Frequency output and pulse output are usually from OC gates so that DC power supplies and load resistors
have to be required.
2.3.7 Pulse Width
Pulse output is active low. Pulse width:1---9999ms
Pulse Width—Max Output Pulse Number(Chart 2)
No. Pulse Width(ms) Max Output Pulse Number/hour(p/h)
9
1 1 1800000
2 5 360000
3 10 180000
4 50 36000
5 100 18000
6 500 3600
7 999 1801
8 9999 180
setting:“Pulse Fact Unit” And “Pulse Fact”. Range is between 00.001 L~ 59.999 m3
Under the same flow, the smaller pulse, the higher frequency output, and the smaller error will be.
L-mag electromagnetic flow meter converter supporting sensor diameter range: 3 to 3000 mm.
3、4、5、6、8、10、15、20、25、32、40、50、65、80、100、125、150、200、250、300、320、
350、400、450、500、600、700、800、900、1000、1100、1200、1300、1400、1500、1600、1700、
1800、1900、2000、2100、2200、2300、2400、2500、2600、2700、2800、2900、3000;
2.4.2 Sensor Code
It is referred to the produced date of sensor and the serial number of product that can keep the sensors
has to be set into Sensor Coefficient Parameter when it runs with converter.
2.4.4 Exat. Frequency
L_Mag D affords six exciting frequency types(default setting is 6.25Hz,25Hz and 30Hz are High-frequency
excitation frequency ):3.125Hz,4.167Hz,6.25Hz,12.5Hz,25Hz,30Hz. The small size sensor should use 6.25
Hz, and large size sensor should use 3.12Hz or 4.16Hz. When using, please select low exciting frequency first,
if the zero of velocity is too high, select other lower exciting lower frequency in turn.
10
Note: Demarcate on which exciting type, working on it only. If use high frequency excitation,should choose
12.5Hz,25Hz,30Hz
2.4.5 Lineary correct
Please refer to Appendix 1.
2.5 Communication
2.5.1 Communication Mode
L-mag D converter can accomplish three communication mode: MODBUS,HART,PROFIBUS; This is
User use 5 byte code to enter, and can modify the positive accumulating volume (∑+). Usually, it is
11
Chart 3 Keys And Display
When power on,the flow meter will automatically come into measurement state. Under automatically
measurement state, the flow meter will complete measurement function automatically and display
measurement data. Under the parameter setting way,if user want to set the parameter must change the flow
meter from measurement state to parameter setting state first. In parameter setting state,user can use keys to
“Right”key:Press the “right”key,the flow meter will enter into function selection screen
12
3.2Functions select menu
Chart 3
Parameters Set
Touch “Right”key,Flow meter will enter into the state“00000” of input password,Input the password(different
grade of password please refer to APPENDIX 3) and then make cursor move to “Enter” key, touch “Enter”
key. It displays “ parameter setting”,then touch “Left”or “Right” key make cursor move the below of
Touch “ Right” key, flow meter will enter into the state “00000” of input password, Input the
password(different grade of password please refer to APPENDIX 3) and then make cursor move to to
“Enter” key, touch “Enter” key. It displays“parameter setting”,then press“Up” or “ Down” key to find the
function of “Cl r Total Rec”. Input the password of Cl r Total Rec ,touch “Left” or “ Right” key to make the
cursor move to “Enter”key, Press“Enter” key. When the Cl r Total Rec password back to “00000”,the clear
13
4.Converter Picture
5.
■ Function(Option):MODBUS、HART、 GPRS、PROFIBUS;
Relative Humidity:5%~90%;
14
5.5 Dimension
15
5.8 Digital Frequency Output
Frequency output range:1~10000Hz;
Alarm output drive:output by Darlington pipe,the highest subjected voltage is 36VDC,maximum of output
current is 250mA.
HART interface:designed by standard of HART , if you choose our hand held unit , you can display the
Insulated voltage between simulated input and alarm power supply should be higher than 500V;
Insulated voltage between simulated input and AC power supply should be higher than 500V;
Insulated voltage between simulated output and AC power supply should be higher than 500V;
Insulated voltage between simulated output and earth should be higher than 500V;
16
Insulated voltage between pulse output and AC power supply should be higher than 500V;
Insulated voltage between pulse output and earth should be higher than 500V;
Insulated voltage between alarm output and AC power supply should be higher than 500V;
Insulated voltage between alarm output and earth should be higher than 500V;
Frequency output mode general can be used in control application, because it responses the percent flux.
Users can choose pulse output when the equipment is applied to count.
Pulse output mainly applies in count mode. A pulse output delegates a unit flux, such as 1L or 1M3 etc.
Pulse output unit can be set from range 0.001L~59.999m3 .When users choose the pulse unit, they should
notice the match of the flux range of flow meter and pulse unit. For volume flux, count formula as follows:
QL = 0.0007854 × D2 × V (L/S)
QM = 0.0007854 × D2 × V × 10-3(M3/S)
D-nozzle(mm) V-velocity(m/s)
The oversize flux and too small pulse unit will be made the pulse output over the up limit. Generally, pulse
output should be controlled below 500Hz. However, the too small flux and too large pulse unit will be made
the instrument exports a pulse long time. Detailed setting can refer to the chart of “Pulse width-Maximum
Otherwise, pulse output is different from frequency output. When pulse output cumulates a pulse unit, it
exports a pulse. Therefore, pulse output is not equality. Generally, measure pulse output should choose to
17
5.13.3 The connection of digital output
Digital output has two connected points: digital output connected point, digital ground point, and symbol as
follows:
POUT is open collector output, user may refer to next circuit to connect.
Commonly user’s photo electricity coupling current is about 10mA, so about E/R=10mA, E=5~24V
18
Commonly relay needs E as 12V or 24V. D is extend diode, now most middle relays has this diode inside. If
POUT
Parameter Test condition Min Typical Max Unit
Vo l t a g e IC=100 mA 5 24 36 V
IC=100mA
Frequency 0 5000 7500 HZ
Vcc=24V
It can be advanced simulation signal output distinguish. User can select the range of measure.
Parameters before ex-factory, manufacturer have already set the suitable parameters. In normal case,there’s
hen the converter is running 15 minutes, the inner of converter becomes stabilization. Preparative 0.1%
19
1.000
IOUT
DC20V
Converter
ICOM
When the converter getting into parameter setting, selecting to “Analog Zero” and enter to it. The standard
To select “Analog Range” to enter.Adjust the converter parameter make ampere meter is
20mA(±0.004mA)
Adjust the current zero and the full range, the current function of the converter reached exactness.The
line degree of current output of conversion should be controlled within the scope of 0.1%
You can place the standard signal source in 75%、50%、25%,and check the line degree of current output
※ Note : After L-mag D Electromagnetic flow meter converter 、 sensor be connected to fluid
Use copper line to connect the pipeline before the sensor and pipeline after the sensor tightly.
When set the zero point,make sure the liquid in the pipeline is static
Make sure the electrode oxidation film inside sensor is stable(Usually make the electrode and liquid
6. Alarm Information
PCB of electromagnetic flow meters converters uses SMT, so for user, it is unable to service, and cannot open
L-mag D Intelligent converters have self-diagnose function. Without trouble of power and hardware
circuit, the normal trouble can be alarmed correctly. This information displays on the left of LCD. The trouble
is like this:
SYS ---- System exciting alarm.; MTP ---- Flow empty pipe alarm;
CUT ---- Small signal Cut Alarm; REV ---- Reverse Flow Cut Alarm
20
HIG ---- Flow high limit alarm; LOW---- Flow low limit alarm
7. Troubleshooting
7.1 No display
a) Check the power supply connection;
b) Check if the total resistance of sensor’s exciting coil resistances less than 150Ω;
* When shorting circuit three connectors SIG +, SIG -, SGND of converter, and no “Empty Alarm”
displayed then the converter works OK. In this case, it is possible that conductivity of measured fluid
may be small or empty threshold of empty pipe and range of empty pipe are set wrongly.
Let the flow is zero, then the displayed conductivity should be less than 100%.
Resistances of SIG+ to SGND and SIG- to SGND are all less than 50kΩ (conductivity of water)
during measurement operation. (It is better to test the resistances by means of multimeter with pointer
* The DC voltage should be less than 1V between DRS+ and DRS- testing the voltage by means of
multimeter. If DC voltage is larger than 1V, the electrode poles of sensor were polluted that have to be
cleaned.
21
7.4 Flow measurement inaccuracies
*Check the sensor coefficient, whether the sensor zero calibration sensor plate or single factory settings
Appendix 1
Nonlinear Amendment function Additional Instruction
Nonlinear amendment function,in principle is used for line regulation of low flow which under 0.5m/s. The
function is designed to four amendments, and divided into four flow velocity points and four correction
factors.
Nonlinear amendment coefficient works on the basis of the original transducer calibration coefficient, so
please close nonlinear amendment function before calibrating the transducer coefficient, and open the
function to realize nonlinear amendment after calibrating. Set correction points and correction factors
according to the nonlinear segment of transducer, if be the appropriate settings, do not have to re-calibration.
As a rule, the flow velocity which calculated form transducer coefficient is called original flow velocity, and
the other which gained from non-linear amendment is called correction flow velocity. The relationship
The intermediate value of correction coefficient is 1.0000,when bigger than it is considered as positive
22
coefficient (increase), and smaller is considered as negative coefficient (decrease).
Setting Grad
Code Parameter words
Way
Range
es
Flow set up Select
1 Flow unit Select L/h、L/m、L/s、m3/h、m3/m、m3/s 2
2 Flow total unit Select 0.001m3~1m3 、0.001L~1L、 2
3 Clear total key Set count 0~99999 3
4 Meter Factor Set count 0.0000~5.9999 2
5 Zero correction Set count 0~±9999 2
6 Fluid density Set count 0~19.999T/m3 2
7 Low flow cutoff Set count 0~599.99% 2
8 Cutoff alarm en. Select Enable/Disable 2
9 Flow direction Select Plus/ Reverse 2
10 Noise limit tim. Set count 0s~20s 3
11 Noise limit val. Set count 0%~30% 3
12 Flow filter time Select 1~60S 2
13 Flow range Set count 0~99999 2
14 Reverse flow en. Select Enable/Disable 2
Alarm setup
1 High alarm ena. Select Enable/Disable 2
2 High alarm val. Set count 000.0~599.99% 2
3 Snsr MT range Set count 0~5.9999 5
4 Snsr MT zero Set count 0~59999 5
5 Snsr MT alarm Set count 0~59999 2
6 Snsr measure ena. Select Enable/Disable 2
7 System alarm ena. Select Enable/Disable 2
8 Low alarm value Set count 000.0~599.99% 2
9 Low alarm ena. Select Enable/Disable 2
Output setup
1 Digital output Set count 1~ 10000 Hz 2
2 Analog out.test Set count 0.0000~0.9999 2
3 Analog range CRC Set count 0.0000~3.9999 5
4 Analog zero CRC Set count 0.0000~1.9999 5
5 Analog output Select 4-20mA 2
6 Pulse output Select Frequency/pulse 2
7 Pulse width Select 1~9999ms 2
8 Pulse factor Set count 00.001~ 59.999 2
9 Pulse unit Select m3 、L 2
Sensor setup
1 Sensor size Select 3~3000 2
2 Sensor code 2 User set Product number(0-99999) 4
3 Sensor code 1 User set Finished Y M(0-99999) 4
4 Velocity point 5 User set Set Velocity 4
5 Velocity value 4 User set 0.0000~1.9999 4
6 Velocity point 4 User set Set Velocity 4
7 Velocity value 3 User set 0.0000~1.9999 4
8 Velocity point 3 User set Set Velocity 4
23
9 Velocity value 2 User set 0.0000~1.9999 4
10 Velocity point 2 User set Set Velocity 4
11 Velocity value 1 User set 0.0000~1.9999 4
12 Velocity point 1 User set Set Velocity 4
13 Lineary correct Selec Enable/Disable 4
14 Sensor factor Set count 0.0000~5.9999 4
15 Exat.frequency Select 3.125Hz~12.5Hz 4
Communication
1 Communication code Select MODBUS、HART、PROFIBUS 2
2 Check mode Set count 0~250 2
3 Baud rate Select 300~38400 2
Communication No Parity Check;
4 address
Select
Odd Parity Check;Even Parity Check
2
Meter parameters
1 Pass Word 1 User set 0~59999 5
2 Rev.total high User set 0~9999 5
3 Rev.total low User set 0~99999 5
4 Fwd. total high User set 0~9999 5
5 Fwd. total low User set 0~99999 5
6 Meter Code 2 Factory set Finished Y /M(0-99999)
7 Meter Code 1 Factory set Finished Y /M(0-99999)
8 Password 4 User set 0~59999 5
9 Password 3 User set 0~59999 5
10 Password 2 User set 0~59999 5
11 Password 1 User set 0~59999 5
Parameters of converters can decide the running status, process and output ways as well as state of output. Correct option and
setting of parameters can keep the converters running optimally and get higher accuracy of output bother in display and in
measurement.
There are 5 grades of passwords for setting parameters function. Grades 1 to grade 4of passwords are for users and grade 5
of password is for manufacturer. Users can reset their passwords of grades 1~4 in grade
Users can check converters parameters in any grade of password. However, if users want to change parameters pf converters,
Grade 1 of password (set by manufacturer as 00522): users can only read parameter;
24