Professional Documents
Culture Documents
Reference Guide
1
RIK Landscape Package for Archicad Manual
【Hardscape】
Road Creator............................................................ 3
Slope Adjuster -Percentage ..................................... 6
Slope Adjuster -Height............................................. 7
Slant Tool ................................................................. 8
Land Formation ..................................................... 10
Fence Arrangement ............................................... 11
Fence Arrangement Setting................................... 12
Curb Creator .......................................................... 13
Rock Wall Creator .................................................. 15
Stone Arrangement………………..……………………..……16
Wood Deck Creator ............................................... 17
Calculation Palette ................................................ 19
【Softscape】
Billboard Tool………………………………………………………..23
Hedge Creator……………………………………………………….24
Shrubbery Creator………………………………………………...25
Plants Random Setting…………………………………………..27
Green Wall Arrangement……………………………………….28
Plants Consecutive Arrangement……………………………29
2
Road Creator
There are two ways to create road.
① Create a road along the outline of the site
② Create a road by drawing a reference line.
・Level Settings:
Input a value for the road level. Define levels at each
The Road Creation Setting
point to create a slanted road.
・Width Settings:
Select one or input value for the road width.
・Reference Line:
Select one side you want the road to be. If you want to
install an object such as grating or curbstones between
the road and the reference line, choose one from
choices.
3
To create a road by drawing a reference line.
2. Draw a reference line for the road. Double click at the end point to finish.
・After choosing the concrete curbstone as site boundary in setting, these curbstones are placed as grouped objects.
4
・Object Selection Settings appears.
・Example
input
1 in 2nd column
2 in 3rd through 6 columns
3 in 7th column
Tip: If you check “Change to Round Type” at the bottom of transform settings, the edge of curbstone changes to round
type.
5
Slope Adjuster -Percentage
1. Draw the shape of the floor plan with [Slab], [Mesh], or [Fill] tool.
Note: No height setting is required when entering with the [Slab] or [Mesh] tool.
4. Click on point ① ② to set the reference line, and ③ to set the gradient direction.
Slab
③
① ②
Road
(7.) If you checked the “Adjust vertex level” box, the setting on
the right appears. Enter a value for each level and
when you are done, click OK to finish.
6
Slope Adjuster -Height
1. Draw the shape of the floor plan with [Slab], [Mesh], or [Fill] tool.
7
Slant Tool
Use this tool to adjust elements on a slanted surface on a 2D screen.
3. Place an object.
4. Select the object you want to adjust and click “Slant adjustment”
5. Draw a reference from the start (1st ) and end (2nd ) point of the slope.
8
6. Enter each height.
Note: The unit is in mm.
It is easier to use level dimension tool to obtain the height first.
7. Click OK
9
Land Formation
Use this function to create undulating elements from contour lines.
5. Click OK to finish.
10
Fence Arrangement
3. Select the wall you want to place the fence on with arrow tool.
2. Click where you want to place a fence/handrail object. Double click at the end point to finish.
Note: this function automatically acquires the level of the points. However, the selected object needs to be available
for this feature.
3. Click OK to finish.
11
Fence Arrangement Settings
Change the fence settings such as height and color at your preference and register it in advance to use in “Fence
Arrangement”.
12
Curb Creator
1. Draw a reference line using [Line], [Arc/Circle], or [Polyline] tool.
③ Tilt Adjustment
Check this box to adjust angle automatically.
⑥
④ Maximum Height
⑥ Position of curb
Height
Width ※When creating joints,
3. Specify each setting and click OK to finish.
From GL Spacing=Joint Width
14
Rock Wall Creator
1. Click “Rock Wall Creator”
2. Click OK to finish.
Note: You can also ungroup the object then modify the stone material one by one.
15
Stone Arrangement
Stone Arrangement
4. By clicking the starting point to end input, stones will be placed on the area.
You can also arrange stones by using the magic wand tool.
16
Wood Deck Creator
Creates various shapes of wood decks. You can also create handrails and steps at the same time.
1. Draw the outline of wood deck using [Slab] tool, or [Line] and [Fill] tool.
Foundation Pitch
Depending on the shape of the wood deck, it may not be arranged at the specified pitch.
In that case, adjust the position of the post
X Direction
17
Option Settings
Select one of the fence types to arrange fence on the deck, and check “Available” for the deck step to create steps.
When you select these options and click OK, the cursor changes to a pencil mark on the deck.
1. Draw a reference line for the fence and double click at the end point to finish.
2. Input the steps using the square box which appears on the screen when you finish fence input.
Note:
The created deck is grouped at first. By ungrouping each object, you can change the settings
individually.
18
Calculation Palette
1. Click “Calculation Palette”
3.Select the area and click “Notation” to place the result on the plan as an object.
Note: The result is copied to the clipboard when you click the item such as height, perimeter and areas. You can paste
the result on the drawing or other software such as Excel.
19
Wall calculation
Surface Area 2
Center
Short Side
Long Side
Surface Area 1
Top-end Area
Surface Area 1
(Back side=surface area 2)
Header Area
Slab/Mesh calculation
20
By selecting both mesh and slab elements and click “Obtain”, areas combined will be calculated.
Measuring length
2. Click at the side you want to measure and double click to finish.
21
Measuring Area
2. Enclose the area you want to measure and double click to finish.
22
Billboard Tool
You can turn a tree/plant on the drawing in the direction of the camera and change the way it is displayed.
○
1 Line Drawing… Display the plants as line drawing.
○
2 Colored Drawing… Display the plants with picture file.
○
3 Plan View…Display the plants as plan view
○
4 Rotation… Rotate the plants on the plan to face the camera.
23
Hedge Creator
1. Click “Hedge Creator”
1. Select a plant
Note: The white line around the hedge disappears after rendering.
② Height
①
③ Shadow: (Default: None )
The rendering speed is increased by not
displaying the shadow of the hedge when
②
rendering.
④ 2D Type:
Change the hedge display in the plan view. ③
④
Type 01
Type 02 24
Shrubbery Creator
1. Click “Shrubbery Creator”
① Arrangement:
③
② Offset and Pitch:
Offset
③ Type:
Select [random] to choose a combination from the “Plants Random setting”
2D 3D
25
Changing the shrubbery settings
①
2. Right-click to click “Object Selection Setting”
① Bottom Elevation to GL ②
② Height
③ Simple Expression
When displaying the elevation plan,
simple expression will speed up the display
3. Click OK to finish.
Note: When you choose “Simple Expression”, the outline of the shrubbery won’t be displayed in elevation plan. To
avoid confusion, add a line using [Line] tool.
26
Plants Random Setting
2. Settings appears.
Note: Maximum number you can register is 5 plants per a pattern. If 5 plants have been already registered, you need to
delete one to register a new plant.
27
Green Wall Arrangement
1. Click “Green Wall Arrangement”
・Settings appear.
Note:
3D
28
Plants Consecutive Arrangement
Arranges bedding plants along a line.
① Position:
Random: Arranges the plants in random.
Unified: Arranges one of the selected plants
② Edge Arrangement:
Center at Edge Point: Place the object using the edge
points as the center.
①
③ Arrangement Pitch:
Specify the arrangement pitch
29
___________________________________________________________________________________________________
RIK Landscape Package for Archicad -Reference Guide
Web: https://products.rikcorp.jp/rlsp-for-archicad/
*Unauthorized copying of this product and the manual, in whole or in part, is prohibited.
30