Professional Documents
Culture Documents
Page 1 of 2
MasterFlow 870
Age 10ºC 20ºC 30ºC
2
ASTM C230/C230M, 100-120% flow by flow table after
5 drops in 3 s or AS1478.2 Appendix D, 20-30cm lateral
1 day Positive Positive Positive flow in the flow trough.
3 days Positive Positive Positive The performance data is typical and based upon
7 days Positive Positive Positive controlled laboratory conditions. Actual performance on
the job site may vary from these values based on actual
28 days Positive Positive Positive
site conditions. Field and laboratory tests should be
Test Method: ASTM C1090 (CRD-C621) conducted on the basis of the desired placing
consistency rather than strictly on indicated water
Flow Retention – effect of temperature on flow demand. If the project requires strength tests be made
retention at a flowable consistency on site do not use cylinder moulds.
Age 10ºC 20ºC 30ºC VOC content: 6g/L Test method: SCAQMD 304-91
Initial 100% 100% 100%
ESTIMATING DATA
After 30 minutes 75% 90% 65%
One 25 kg bag of MasterFlow 870 mixed according to
After 1 hour 60% 75% 60% directions will yield the following flowable grouts at 20°C:
Bleeding, Plastic Density and Setting Time – effect Quantity of Nil 13 kg 25 kg
of temperature on plastic properties at a flowable aggregate
consistency
Temp. Bleeding Plastic Setting Time Add 4.2 L water 13.0L 18.5L 23.1 L
% Density
kg.m3 Initial Final The material requirement at flowable consistency
(hours) (hours) without any aggregate is 18.5 kg/m2 for 10 mm
thickness.
10ºC 0 2120 4.6 6.0
20 ºC 0 2155 4.5 5.2 APPLICATION
30 ºC 0 2245 3.0 4.0 For information about application, please obtain a copy
of the Master Builders Solutions “Application Guide for
Test Method: Bleeding AS1012.6; Plastic density MasterFlow Cementitious Precision Grouts” from your
AS1012.5; Setting time AS1012.18 local representative. For ‘dry pack’ (damp pack)
Water Demand – Actual water demand will depend on application, refer to MasterFlow 700.
consistency required and temperature (both ambient
and grout). As a guide, the following table indicates the PACKAGING
approximate quantity of water required to mix a 25kg MasterFlow 870 is packaged in 25kg bag.
bag of MasterFlow 870 to various consistencies.
SELF LIFE
Temperature Consistency MasterFlow 870 has a shelf life of approximately 12
Flowable 1 Plastic 2 months when stored in a cool dry environment.
20 ºC 4.2 litres 3.25 litres PRECAUTIONS
1AS1478.2 Appendix D, 45-55cm lateral flow in the flow For detailed Health, Safety and Environmental
trough. Recommendations, please consult and follow all
instructions on the product Material Safety Data Sheet
(MSDS) from our office or our website.
® = registered trademark of a MBCC Group member in many countries of the world MAP#MasterFlow 870 v2-12.2020
The technical information and application advice given in this Master Builders Solutions publication are based on the
STATEMENT OF present state of our best scientific and practical knowledge. As the information herein is of a general nature, no
RESPONSIBILITY assumption can be made as to a product's suitability for a particular use or application and no warranty as to its accuracy,
reliability or completeness either expressed or implied is given other than those required by law. The user is responsible
for checking the suitability of products for their intended use.
Field service where provided does not constitute supervisory responsibility. Suggestions made by Master Builders
NOTE Solutions either orally or in writing may be followed, modified or rejected by the owner, engineer or contractor since they,
and not Master Builders Solutions, are responsible for carrying out procedures appropriate to a specific application.
www.master-builders-solutions.com/en-id