Professional Documents
Culture Documents
T-20
Service Manual
Version : Rev. D
2-2 Base......................................................................................................................................................................... 4
6 Troubleshooting........................................................................................................................................................... 30
7. Contact us.................................................................................................................................................................... 33
1. General View
1.1 Outer-Front View (T10)
HANDLE
POWER JACK
OPERATION PANEL
BOTTOM PLATE
-Outside
-Inside
POWER SWITCH
-ON
-OFF
1
1.2 Outer-Rear View (T10)
SPRING SLICE
CONTROL MECHANISM
(Dancer Arm)
GUIDE TRACK
LED INDICATOR
2
2. Part List Table
2-1 1 Main
※ The red word are the parts for VR version rewinder usage.
3 227-116013-040 HOUSING,PHD2.0-2*8P,90mm,1061#28AWG 1
9 750-036800-000 U-TYPE,SPRING,T-10 1
15 765-316101-100 Nut,M16*1*19*3t,NI 1
16 775-621020-102 E-RING,NI,Φ10*Φ20*1.0t/mm 1
20 760-017700-001 VR Knob,T-10 1
3
2-2 Base
1 735-001600-002 Base,Al-Extrusion,T-10 1
4
2-3 Control Mechanism (Dancer Arm)
6 730-001300-000 PM,20-1-4C,T-10 2
12 775-620409-062 E-RING,Φ4.0*Φ9.0*0.6t/mm,Nickle 1
5
2-4 Encoder
6
2-5 Fixed bracket for motor and shaft
5 220-345705-104 STEPPING,MOTOR,H5750V15,1.8°,57mm,24V,Unipolar 1
7
2-6 Main bracket
3 730-001200-000 Bush,6053CT,T-10 1
8
2-7 Shaft
※The orange words are the different parts between T10 and T20.
9
3. Method of Disassembly and Assembly
3-1 Side Cover
3-1-1 Disassemble the side cover
Step 1. Remove the 8 screws (red circles) as the figure 1 indicates.
Step 2. Remove the side cover in the direction of the arrow, as figure 2 indicates.
Figure 1
Figure 2
10
3-1-2 Assemble the side cover
Step 1. Assemble the side cover in the direction of the arrow, as figure 1 indicates.
Figure 1
Figure 2
11
3-2 Motor and Bracket Module (021-T10003-000)
3-2-1 Disassemble motor and bracket module
Step 1. Remove motor and bracket module in the direction of arrows
1. Remove the 8 screws on both sides and top side of the side cover.
4. Remove the pulley of driven, e-ring and graphite washer in the direction of the arrow.
7. Detach the motor and bracket module in the direction of the arrow.
1. Remove the 4 screws (red circles) from the motor and bracket module.
2. Detach the motor from the bracket in the direction of the arrow.
4. Detach the belt pulley from the motor in the direction of the arrow.
12
3-2-2 Assemble motor and bracket module
Step 1. Attach motor to the bracket in the direction of the arrow.
1. Attach the belt pulley to the motor in the direction of the arrow.
3. Attach the motor to the motor bracket in the direction of the arrow.
1. Attach the motor and bracket module in the direction of the arrow.
4. Assemble the graphite washer, e-ring and pulley of driven in the direction of the arrow.
7. Tighten the 8 screws on both side and top side of the side cover.
13
3-3 Main Board Module (021-T10001-000)
3-3-1 Disassemble the main board module
Step1. Disassemble the main board
1. Remove the screws on both side and top side of the side cover.
14
3-3-2 Assemble the main board module
Step1. Assemble the main board
4. Tighten the 8 screws on both sides and top side of the side cover.
15
3-4 Shaft and Plate Module
3-4-1 Disassemble Shaft and plate module
Step 1.Remove Shaft and plate module
16
3-4-2 Assemble Shaft and plate module
Step 1. Assemble Shaft and plate module
1. Attach the label holder for sheet metal in the direction of the arrow and tighten the screws.
17
3-5 Dancer Arm Module
3-5-1 Disassemble dancer arm module
Step 1. Disassemble dancer arm module
2. Remove the motor bracket and main board as the arrow indicates.
18
3-5-2 Assemble dancer arm module
Step 1. Assemble dancer arm module
2. Attach motor bracket and main board in the direction of the arrow.
19
3-6 V-Belt(760-011900-001)
3-6-1 Disassemble v-belt
Step 1. Remove the v-belt from belt pulley in the direction of the arrow, as the figure below indicates.
20
3-6-2 Assemble the v-belt
Step 1. Attach the v-belt to belt-pulley as the arrow indicates.
(Note: Please adjust the torque value to appropriate value when attaching the v-belt.)
21
3-7 SWITCHING POWER PARTS,60W,GoDEX,T-10 (021-T10002-000)
※ Power Cord
Part No. Name
226-000001-200 Power cord For US
226-000010-100 Power cord For EU
226-000015-611 Power cord For China
226-000011-400 Power cord For Uk
226-000003-500 Power cord For AU
226-000036-D00 Power cord For INDIA
22
3-8 Spare Parts List
編號 料號 品名 頁碼 備註
1 021-T10001-000 MAIN PCB ASS'Y,GoDEX,T-10 P14
2 021-T10002-000 SWITCHING POWER PARTS,60W,GoDEX,T-10 P22
3 021-T10003-000 MOTOR PARTS,GoDEX,T-10 P12
23
4. Main Board Connecter Position
2 3
1
24
5. Download Tool
Step 1. After installing Programming Tool, the program is displayed at the screen, as the figure below
indicates.
Step 2. After executing the program, please select “ COM PORT ”, as the figure below indicates.
25
Step 3. Press “Connect” and switch on the rewinder simultaneously.
(Note: Depend on the computer setting of customers, the selection of “COM PORT” may differ.)
26
Step 5. Select the desired firmware file
27
Step 7. Wait for the downloading process until the “PASS” symbol is displayed. The firmware is completely
updated.
28
29
6 Troubleshooting
Rewinder Full
Lights up in pink
Step 3.
of the arrow.
Step 2.
Step 1.
Pull the label stock out in
Power off
the direction of the arrow
30
When the label roll falls
Lights up in pink
Step 1.
Power off
Step 2.
tightened
31
When the label roll departs from the dancer arm
Lights up in pink
Step 1.
Power off
Step 2.
dancer arm
32
7. Contact us
GoDEX International
(台灣) (America)
A, Camarillo, CA 93012
(Europe) (中国)
Address:
Arnzhäuschen 36
D-42929 Wermelskirchen
Germany
33